Rev. 1812171208 Part No. 161500-18-004 Copyright

Rev. 1812171208
Part No. 161500-18-004
Copyright 2017 Winnebago Industries, Inc. All rights reserved.
TABLE OF CONTENTS
1 – INTRODUCTION
About this Manual ............................................................................................................................ 1-1
Safety Messages Used in this Manual .............................................................................................. 1-1
Pre-Delivery Inspection .................................................................................................................... 1-2
Before Driving .................................................................................................................................. 1-2
Front Axle Tire Alignment ............................................................................................................... 1-2
Service and Assistance ...................................................................................................................... 1-2
Reporting Safety Defects .................................................................................................................. 1-2
Occupant and Cargo Carrying Capacity Label ................................................................................. 1-3
Vehicle Certification Label ............................................................................................................... 1-4
Specifications and Capacities ........................................................................................................... 1-5
Owner and Vehicle Information ....................................................................................................... 1-6
General Warnings ............................................................................................................................. 2-1
Driving Safety ................................................................................................................................... 2-1
Fuel and Propane Gas ....................................................................................................................... 2-2
Propane Gas Leaks ............................................................................................................................ 2-3
Propane Gas Leak Detector .............................................................................................................. 2-3
Carbon Monoxide Alarm .................................................................................................................. 2-4
Carbon Monoxide Warning .............................................................................................................. 2-5
Smoke Alarm .................................................................................................................................... 2-5
Fire Extinguisher ............................................................................................................................... 2-6
Electrical ........................................................................................................................................... 2-6
Loading ............................................................................................................................................. 2-6
Maintenance ...................................................................................................................................... 2-7
Emergency Exits ............................................................................................................................... 2-7
Slideout Rooms ................................................................................................................................. 2-8
Formaldehyde Information ............................................................................................................... 2-8
Mold, Moisture, and Your Motorhome ............................................................................................ 2-9
Roof and Ladders ............................................................................................................................ 2-10
Roadside Emergency ...................................................................................................................... 2-10
Jump Starting .................................................................................................................................. 2-11
Engine Overheat ............................................................................................................................. 2-12
3 – DRIVING YOUR MOTORHOME
Seats – Driver/Co-Pilot ..................................................................................................................... 3-1
Fold-Down Dinette Seat ................................................................................................................... 3-1
Seat Belts .......................................................................................................................................... 3-1
Child Restraints ................................................................................................................................. 3-2
Keys .................................................................................................................................................. 3-3
Hazard Warning Flashers .................................................................................................................. 3-3
5 - DASH / AUTO
2 – SAFETY AND PRECAUTIONS
Table Of Contents
Mirrors – Manual Sideview Exterior ................................................................................................ 3-4
Mirrors – Power Sideview Exterior .................................................................................................. 3-4
Battery Boost Switch ........................................................................................................................ 3-5
Air Conditioner/Heater – Automotive (Dash) .................................................................................. 3-5
Radio In-Dash/Rearview Monitor System ........................................................................................ 3-6
Engine Access – Interior ................................................................................................................... 3-7
Engine Cooling System .................................................................................................................... 3-7
Tires .................................................................................................................................................. 3-7
Suspension Alignment and Tire Balance .......................................................................................... 3-8
Air Springs – Rear Helper ................................................................................................................ 3-8
Lights ................................................................................................................................................ 3-9
4 – APPLIANCES AND SYSTEMS
Refrigerator ....................................................................................................................................... 4-1
Refrigerator ....................................................................................................................................... 4-2
Refrigerator ....................................................................................................................................... 4-3
Refrigerator ....................................................................................................................................... 4-5
Refrigerator Service Access Compartment ....................................................................................... 4-6
Refrigerator (Exterior) ...................................................................................................................... 4-7
Range and Oven with Glass Range Cover ........................................................................................ 4-7
Microwave Oven ............................................................................................................................... 4-9
Microwave/Convection Oven ........................................................................................................... 4-9
Range Hood ...................................................................................................................................... 4-9
Systems Monitor Panel ..................................................................................................................... 4-9
Water Heater – Gas ......................................................................................................................... 4-10
Water Heater – Gas/ Electric .......................................................................................................... 4-11
Pressure-Temperature Relief Valve ................................................................................................ 4-12
Furnace – Propane Gas ................................................................................................................... 4-13
Ducted Roof Air Conditioning System ........................................................................................... 4-14
Air Conditioner Filter ..................................................................................................................... 4-14
5 – PROPANE GAS
Propane Gas Supply .......................................................................................................................... 5-1
Propane Accessory Connection ........................................................................................................ 5-2
Safe Use of the Propane Gas System ................................................................................................ 5-3
Propane Gas Warnings and Precautions ........................................................................................... 5-4
Propane Gas Pressure Regulator ....................................................................................................... 5-5
Propane Vaporization in Cold Weather ............................................................................................ 5-6
6 – ELECTRICAL
Electrical Cautions ............................................................................................................................ 6-1
Electrical System – House 120-Volt AC .......................................................................................... 6-1
Power Cord – External ...................................................................................................................... 6-1
Inverter Unit – 1000W ...................................................................................................................... 6-3
Power Center ..................................................................................................................................... 6-4
Circuit Breakers – House 120-Volt AC ............................................................................................ 6-5
Table Of Contents
Electrical Outlets – House 120-Volt AC .......................................................................................... 6-6
Ground Fault Circuit Interrupter ....................................................................................................... 6-6
Electrical Generator – 120-Volt ........................................................................................................ 6-6
Electrical System – House 12-Volt DC ............................................................................................ 6-8
House/Coach Battery Disconnect Switch ......................................................................................... 6-8
Battery Access .................................................................................................................................. 6-9
Battery Care ...................................................................................................................................... 6-9
Circuit Breakers and Fuses – House 12-Volt DC ........................................................................... 6-11
7 – PLUMBING
Fresh Water System .......................................................................................................................... 7-1
Water Pump ...................................................................................................................................... 7-2
Ice Maker Water Filter ...................................................................................................................... 7-4
Disinfecting Your Fresh Water System ............................................................................................ 7-4
Shower Hose Vacuum Breaker ......................................................................................................... 7-5
Exterior Shower/Wash Station .......................................................................................................... 7-5
Toilet ................................................................................................................................................. 7-6
Drainage System (P-Traps) ............................................................................................................... 7-6
Waste Water System ......................................................................................................................... 7-6
Holding Tank Heater ........................................................................................................................ 7-8
Waterline & Tank Drain Valves ....................................................................................................... 7-9
Water Heater Bypass and Antifreeze Siphon Valves ..................................................................... 7-10
Winterizing Procedure .................................................................................................................... 7-10
Winterizing Optional Appliances ................................................................................................... 7-12
Water System Drain Valve Locations ............................................................................................ 7-14
8 – ENTERTAINMENT
TV – (Swivel) ................................................................................................................................... 8-1
Audio/Video System Basic Operation .............................................................................................. 8-1
DVD Player ....................................................................................................................................... 8-1
DVD Player ....................................................................................................................................... 8-2
DVD Player ....................................................................................................................................... 8-3
TV Antenna – Digital ....................................................................................................................... 8-4
TV Antenna ....................................................................................................................................... 8-5
TV Signal Amplifier ......................................................................................................................... 8-5
Exterior Cable TV Connection ......................................................................................................... 8-5
Exterior Entertainment Center (Adjustable) ..................................................................................... 8-5
9 – FURNITURE AND SOFTGOODS
Cab Seat Lounge Cushion ................................................................................................................. 9-1
Sleeping Facilities ............................................................................................................................. 9-1
Front Overhead Bunk ........................................................................................................................ 9-1
Sofa/Bed Conversion ........................................................................................................................ 9-3
Sofa/Sleeper ...................................................................................................................................... 9-3
Dinette/Bed Conversion – Dream Dinette™ .................................................................................... 9-4
Dinette/Bed Conversion .................................................................................................................... 9-5
Table Of Contents
U-Shaped Dinette/Bed Conversion ................................................................................................... 9-6
U-Shaped Dinette/Bed Conversion ................................................................................................... 9-7
Dinette Flip-Up Footrests ................................................................................................................. 9-8
U-Shaped Dinette/Bed Conversion ................................................................................................... 9-8
Bunk Beds/Wardrobe Conversion .................................................................................................... 9-9
Pleated Blinds ................................................................................................................................... 9-9
Roller Shades (Manual) – Solar/Blackout ...................................................................................... 9-10
Wood Furniture and Cabinetry ....................................................................................................... 9-11
10 – SLIDEOUT ROOMS AND LEVELING
Slideout Room Lock System .......................................................................................................... 10-1
Slideout Room Operation – Electric ............................................................................................... 10-1
Slideout Room – Extreme Weather Precaution .............................................................................. 10-3
Slideout Room Troubleshooting (Power Gear®) In Wall Slideout ................................................ 10-3
Slideout Emergency Retraction (Power Gear®) In Wall Slideout ................................................. 10-3
General Slideout Care ..................................................................................................................... 10-4
Leveling System ............................................................................................................................. 10-4
Checking Hydraulic Oil Level ........................................................................................................ 10-6
11 – MAINTENANCE AND STORAGE
Sealants – Inspection and General Information .............................................................................. 11-1
Roof ................................................................................................................................................ 11-1
Undercarriage .................................................................................................................................. 11-1
Exterior Automotive Paint Finish ................................................................................................... 11-2
Exterior Graphic Care ..................................................................................................................... 11-4
Plastic Parts – Cleaning .................................................................................................................. 11-5
Exterior Lights ................................................................................................................................ 11-5
Interior Soft Goods ......................................................................................................................... 11-5
Cabinetry – Cleaning ...................................................................................................................... 11-6
Decorative Vinyl Wall Paneling – Cleaning ................................................................................... 11-6
Tables and Countertops .................................................................................................................. 11-7
Solid Surface Countertop – Corian® .............................................................................................. 11-7
Sink – Stainless Steel ...................................................................................................................... 11-7
Range and Refrigerator ................................................................................................................... 11-8
Vinyl Flooring ................................................................................................................................. 11-8
Bathroom ........................................................................................................................................ 11-9
Doors and Windows ........................................................................................................................ 11-9
Vehicle Storage – Preparation ........................................................................................................ 11-9
Vehicle Storage – Removal .......................................................................................................... 11-10
Chassis Service and Maintenance ................................................................................................. 11-11
Coach Maintenance Chart ............................................................................................................. 11-12
12 – MISCELLANEOUS
Loading the Vehicle ........................................................................................................................ 12-1
Weighing Your Loaded Vehicle ..................................................................................................... 12-1
Car or Trailer Towing ..................................................................................................................... 12-3
Table Of Contents
Trailer Wiring Connector ................................................................................................................ 12-4
Towing Guidelines .......................................................................................................................... 12-4
Stabilizing Jacks ............................................................................................................................. 12-6
Awning – Manual ........................................................................................................................... 12-7
Awning – Power ............................................................................................................................. 12-7
Storage Compartment Doors .......................................................................................................... 12-7
Tool and Ladder Storage ................................................................................................................. 12-7
Roof Ladder .................................................................................................................................... 12-7
Power Roof Ventilator .................................................................................................................... 12-8
Windows ......................................................................................................................................... 12-9
Effects of Prolonged Occupancy .................................................................................................... 12-9
SECTION 1 – INTRODUCTION
ABOUT THIS MANUAL
This operator’s manual was prepared to aid
you in the proper care and operation of the
vehicle and equipment.
Please read this manual completely to
understand how everything in your coach works
before taking it on its “maiden voyage”. In
addition, please become familiar with the New
Vehicle Limited Warranty.
NOTE: This manual describes many features of
your motorhome and includes
instructions for its safe use.
This manual, including photographs and
illustrations, is of a general nature only.
Some equipment and features described
or shown in this manual may be
optional or unavailable on your model.
Because of Winnebago Industries®’
continuous program of product
improvement, it is possible that recent
product changes and information may
not be included.
The instructions included in this manual
are intended as a guide, and in no way
extend the responsibilities of Winnebago
Industries beyond the standard written
warranty as presented in this manual.
The descriptions, illustrations, and
specifications in this manual were
correct at the time of printing. We reserve
the right to change specifications or
design without notice, and without
incurring obligation to install the same
on products previously manufactured.
The materials in your InfoCase contain
warranty information and operating and
maintenance instructions for the various
appliances and components in your motorhome.
NOTE: Many of the instruction sheets and
manuals for the various appliances and
components have been incorporated into
the Operator’s Manual Supplement for
your convenience.
Please read the FAQ in Section 1 of the
Operator’s Manual Supplement for more
details.
Throughout this manual, frequent reference is
made to the vehicle chassis manual that is
provided by the manufacturer of the chassis on
which this motorhome is built.
Consult the chassis manual for operating,
safety, and maintenance instructions pertaining
to the chassis section of the motorhome.
SAFETY MESSAGES USED IN
THIS MANUAL
Throughout this manual, certain items are
labeled Danger, Warning, Caution, Notice, or
Note. These terms alert you to precautions that
may involve damage to your vehicle or a risk to
your personal safety. Read and follow them
carefully.
DANGER
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious personal injury.
1-1
5 - DASH / AUTO
Congratulations! We welcome you to the
exciting world of motorhome travel and
camping. You will find it convenient and
enjoyable to have all the comforts of home and
still enjoy the great outdoors wherever you
choose to go.
Before sliding into the driver’s seat, please
become familiar with operations and features. In
addition, spend some time with the dealer when
you take delivery to learn all you can about your
new motorhome.
SECTION 1 –
INTRODUCTION
WARNING
WARNING indicates a hazardous
situation which, if not avoided, could
result in death or serious personal injury.
BEFORE DRIVING
Familiarize yourself with State/Province and
local regulations before traveling. There are
many local rules that may impact your RV
travels.
FRONT AXLE TIRE
ALIGNMENT
C AU T I ON
CAUTION indicates a hazardous
situation which, if not avoided, could
result in minor or moderate personal
injury.
NOTICE
NOTICE is used to address practices not
related to personal injury.
NOTE: A “Note” is not necessarily safetyrelated, but indicates a recommendation
or special point of information that could
assist in understanding the use or care of
a feature item.
PRE-DELIVERY INSPECTION
This motorhome has been thoroughly
inspected before shipment. Your dealer is
responsible for performing a complete predelivery inspection of the chassis and all
motorhome components.
As a part of the pre-delivery inspection
procedure, the dealer is responsible for road
testing the motorhome, noting, and correcting
any problems before delivery.
1-2
We recommend that you have the front
suspension and steering alignment checked and
adjusted after you have fully loaded the vehicle
according to your needs. Thereafter, have
alignment inspected periodically to maintain
vehicle steering performance and prevent uneven
tire wear.
SERVICE AND ASSISTANCE
Your dealer will be glad to provide any
additional information you need, as well as
answer any questions you might have about
operating the equipment in your coach. When it
comes to service, remember that your dealer
knows your vehicle best and is interested in your
satisfaction. Your dealer will provide quality
maintenance and any other assistance that you
may require during your ownership of this
vehicle.
If you need warranty repairs while traveling,
you may take your vehicle to any authorized
Winnebago Industries® dealership and request
their assistance.
See the Service Dealer Directory in your
InfoCase.
REPORTING SAFETY DEFECTS
If you believe that your vehicle has a defect
which could cause a crash or could cause injury
or death, you should immediately inform the
National Highway Traffic Safety Administration
(NHTSA) in addition to notifying Winnebago
Industries, Inc.
If NHTSA receives similar complaints, it may
open an investigation, and if it finds that a safety
defect exists in a group of vehicles, it may order
SECTION 1 –
INTRODUCTION
a recall and remedy campaign. However,
NHTSA cannot become involved in individual
problems between you, your dealer, or
Winnebago Industries, Inc.
To contact NHTSA, you may either call the
Vehicle Safety Hotline toll-free at:
1-888-327-4236; (TTY: 1-800-424-9153)
or go to http://www.safercar.gov
or write to:
Administrator, NHTSA
1200 New Jersey Avenue S.E.
Washington, D.C. 20590
You can also obtain other information about
motor vehicle safety at http://www.safercar.gov.
OCCUPANT AND CARGO
CARRYING CAPACITY LABEL
This label is affixed in the driver’s area next to
or near the Vehicle Certification Label. It
contains vehicle occupant and cargo carrying
capacity along with the number of seat belt
positions in the vehicle. The label also provides
the weight of a full load of water and advises that
this weight, along with the tongue weight counts
as cargo.
If any weight exceeding 45.4 kg (100 lbs.) is
added to your coach between final vehicle
certification and first retail sale, the occupant and
cargo carrying capacity must be corrected and a
label similar to the one shown below will be
affixed inside your coach.
1-3
SECTION 1 –
INTRODUCTION
VEHICLE CERTIFICATION LABEL
This label is affixed to the lower driver side armrest panel, driver door, or the driver side door jamb,
depending on model. It contains vehicle identification numbers and other important reference information.
EXPLANATION OF DATA
1. Chassis manufacturer.
2. Chassis manufacture date.
3. Month and year of manufacture at Winnebago
Industries®.
4. Gross Vehicle Weight Rating: Total
permissible weight of the vehicle, including
driver, passengers, total cargo carried
(including all liquids), and equipped with all
options.
5. Gross Axle Weight Rating: Total permissible
weight allowed for the front and rear axles
(listed in pounds and kilograms).
6. Suitable Tire Choice: Tires recommended to
meet handling and safety requirements. When
replacing any of the tires on your vehicle,
always replace with a tire that meets these
specifications.
7. Suitable Rim Choice: Wheel rims
recommended to meet handling and safety
requirements. When replacing any of the rims
on your vehicle, always replace with a rim that
meets these specifications.
8. Cold Inflation Pressure: Inflation pressures at
Gross Axle Weight Ratings recommended
(while cold) for the tires originally equipped
1-4
on your vehicle. These pressure levels must be
maintained to assure proper handling, safety,
and fuel economy.
9. Rear Axle Wheel Configuration: Single or
Dual as it relates to the inflation.
10. Serial Number: This is the serial number
assigned to the completed vehicle by
Winnebago Industries.
11. Vehicle Identification Number (VIN): This
number identifies the chassis on which the
motorhome is built. The 10th digit of the VIN
designates the chassis model year (G=2016,
H=2017, J=2018, etc.). This information is
useful when ordering chassis repair parts.
12. Type: States the NHTSA designated usage
classification for your motorhome. MPV
signifies a Multi-purpose Passenger Vehicle.
13. Color: Signifies the color code number of the
decor used throughout the vehicle. This
number is necessary for ordering replacement
cushions, curtains, carpet, etc.
14. Winnebago® model year and series/family
name.
15. Model: Lists the Winnebago product model
number of your vehicle.
SECTION 1 –
INTRODUCTION
SPECIFICATIONS AND CAPACITIES
22M
Standard
®
Ford E350
Chassis
Feature Number
Length
Exterior Height 1
Exterior Width
2
3
22R
Optional
®
Ford E450
Chassis
Standard
®
Ford E350
Chassis
Optional
®
Ford E450
Chassis
25B
26A
31D
31G
31K
Standard
Optional
®
®
Ford E350 Ford E450
Chassis
Chassis
Ford® E450
Chassis
Ford® E450
Chassis
Ford® E450
Chassis
Ford® E450
Chassis
16C
16Y
16C
16Y
16C
16Y
16Y
16Y
16Y
16Y
24' 2"
24' 2"
23' 10"
23' 10"
26' 2.4"
26' 2.4"
27' 1"
32' 9"
32' 9"
32' 9"
11'
11'
11'
11'
11'
11'
11' 1"
11' 1"
11' 1"
11' 1"
8' 5.5"
8' 5.5"
8' 5.5"
8' 5.5"
8' 5.5"
8' 5.5"
8' 5.5"
8' 5.5"
8' 5.5"
8' 5.5"
108.3 cu. ft.
44.5 cu. ft.
44.5 cu. ft.
60.4 cu. ft.
60.4 cu. ft.
73.1 cu. ft.
73.1 cu. ft.
45.0 cu. ft.
95.0 cu. ft.
80.7 cu. ft.
Awning Length
14'
14'
14'
14'
17'
17'
18'
17'
19'
20'
Interior Height
6' 10" Front
6' 5.5" Rear
6' 10" Front
6' 5.5" Rear
6' 10" Front
6' 5.5" Rear
6' 10" Front
6' 5.5" Rear
6' 10" Front
6' 5.5" Rear
6' 10" Front
6' 5.5" Rear
Exterior Storage
Interior Width
Freshwater Tank Capacity 4
6' 10" Front
6' 10" Front
6' 10" Front 6' 10" Front
8'
8'
8'
8'
8'
8'
8'
8'
8'
8'
40 gal.
40 gal.
40 gal.
40 gal.
40 gal.
40 gal.
40 gal.
44 gal.
44 gal.
44 gal.
Water Heater Capacity
6 gal.
6 gal.
6 gal.
6 gal.
6 gal.
6 gal.
6 gal.
6 gal.
6 gal.
6 gal.
Holding Tank Capacity - Black 4
40 gal.
40 gal.
21 gal.
21 gal.
21 gal.
21 gal.
35 gal.
37 gal.
37 gal.
30 gal.
Holding Tank Capacity - Gray 4
45 gal.
45 gal.
24 gal.
24 gal.
26 gal.
26 gal.
39 gal.
30 gal.
57 gal.
30 gal.
18 gal.
18 gal.
18 gal.
18 gal.
18 gal.
18 gal.
18 gal.
18 gal.
18 gal.
18 gal.
158"
158"
158"
158"
182"
182"
190"
220"
220"
220"
GVWR
11,500 lbs.
14,500 lbs.
11,500 lbs.
14,500 lbs.
11,500 lbs.
14,500 lbs.
14,500 lbs.
14,500 lbs.
14,500 lbs.
14,500 lbs.
5,000 lbs.
Propane Capacity
Wheelbase
5
GAWR - Front
4,600 lbs.
5,000 lbs.
4,600 lbs.
5,000 lbs.
4,600 lbs.
5,000 lbs.
5,000 lbs.
5,000 lbs.
5,000 lbs.
GAWR - Rear
7,800 lbs.
9,600 lbs.
7,800 lbs.
9,600 lbs.
7,800 lbs.
9,600 lbs.
9,600 lbs.
9,600 lbs.
9,600 lbs.
9,600 lbs.
GCWR 6
18,500 lbs.
22,000 lbs.
18,500 lbs.
22,000 lbs.
18,500 lbs.
22,000 lbs.
22,000 lbs.
22,000 lbs.
22,000 lbs.
22,000 lbs.
55 gal.
55 gal.
55 gal.
55 gal.
55 gal.
55 gal.
55 gal.
55 gal.
55 gal.
55 gal.
Fuel Capacity
Notes:
All information is based upon the most recent data available. Visit the Winnebago Industries, Inc. web page – www.winnebagoind.com – for the most
current product information.
1
The height of each model is measured to the top of the tallest standard feature and is based on the curb weight of a typically equipped unit. The actual
height of your vehicle may vary by several inches depending on chassis or equipment variations. Contact your dealer for further information.
2
Floorplans feature a wide-body design - over 96". You should be aware that some states restrict access on some or all state roads to 96" in body width.
You should confirm the road usage laws in the states of interest to you.
3
The load capacity of your motor home is designated by weight, not by volume, so you cannot necessarily use all available space when loading your
motor home.
4
Capacities are based on measurements prior to tank installation. Slight capacity variations can result upon installation.
5
Capacities shown are the tank manufacturer's listed water capacity (W.C.). Actual filled propane capacity is 80% of listing due to overfilling prevention
device on tank.
6
Actual towing capacity is dependent on your particular loading and towing circumstances which includes the GVWR, GAWR, and GCWR as well as
adequate trailer brakes. Refer to the chassis operator's manual of your motor home for further towing information.
Some chassis are equipped with Flex Fuel capable engines, however the gasoline generator installed in your motorhome is not
capable of running on E85 fuel. Refer to the generator operator's manual for more information on proper fuel.
1-5
SECTION 1 –
INTRODUCTION
OWNER AND VEHICLE INFORMATION
OWNER INFO
Owner’s Name(s) __________________________________________________________________
Address __________________________________________________________________________
__________________________________________________________________________
VEHICLE INFORMATION
Motorhome Model Number __________________________________________________________
Motorhome Serial Number ___________________________________________________________
Chassis Vehicle Identification No. (VIN) ________________________________________________
Vehicle Mileage at Delivery __________________________________________________________
Selling Dealer Name ________________________________________________________________
Address __________________________________________________________________________
__________________________________________________________________________
YOUR WINNEBAGO INDUSTRIES® DEALER /SERVICE CENTER
Name ____________________________________________________________________________
Address __________________________________________________________________________
__________________________________________________________________________
Contact ____________________________________________Phone ________________________
CHASSIS SERVICE CENTER
Name ____________________________________________________________________________
Address __________________________________________________________________________
__________________________________________________________________________
Contact ____________________________________________Phone ________________________
RV INSURANCE POLICY
Company _________________________________________________________________________
Policy Number ____________________________________________________________________
Agent______________________________________________Phone ________________________
1-6
SECTION 2 – SAFETY AND PRECAUTIONS
•
•
•
•
•
•
•
•
•
DRIVING SAFETY
Only seats equipped with seat belts are to be
occupied while the vehicle is moving.
Make sure all passengers have seat belts
fastened. Lap belts should fit low on the hips
and upper thighs. The shoulder belt should be
positioned snug over the shoulder.
For pregnant women: Never place the
shoulder belt behind your back or under your
arm. Adjust the lap belt across your hips/
pelvis, and below your belly. Place the
shoulder belt across your chest (between your
breasts) and away from your neck.
Child restraints should be installed properly
according to manufacturer’s instructions. See
“Child Restraints”.
All moveable or swiveling seats should be
placed and locked in travel position while the
vehicle is moving.
Never let passengers stand or kneel on seats
while the vehicle is moving.
Sleeping facilities are not to be utilized while
vehicle is moving.
Examine the escape window and be familiar
with its operation.
Inspect the fire extinguisher monthly for
proper charge and operating condition. This
should also be done before beginning a
vacation or any extended trip.
WARNING
This motorhome has been designed,
manufactured and tested with concern for
the protection of it’s occupants. We
recommend you perform the following
inspections for your safety and the safety
of your passengers before starting your
vehicle.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
LP GAS SYSTEM - Turn off at tank for
traveling. Test for leaks upon arrival at
destination before lighting pilots.
WHEELS - Inspect for damage and check
lug nuts for tightness.
TIRES - Inspect for wear and damage
and check for recommended air
pressure.
LIGHTING - Test for proper operation of
all interior and exterior lights including
dash lights, headlights, tail lights, brake
lights, clearance lights, and turn signals.
EXITS - Inspect release mechanism on
emergency exit window, test both locks
on main entrance door for ease of
operation and instruct passengers how to
use both means of exit.
SEAT BELTS - Direct passengers to
designated seats, be certain swivel seats
are locked into position, and require use
of a seat belt. See operator’s manual for
occupancy and weight restrictions.
APPLIANCES - Turn off and latch or lock
doors where provided.
LOOSE PARCELS - Store securely.
UTILITY SUPPLY LINES - Disconnect all
electrical, sewer and water lines and
secure properly.
ENTRANCE DOOR STEP - Assure step
is in retracted position for traveling.
5 - DASH / AUTO
GENERAL WARNINGS
Read your motorhome and chassis
owner’s manual for further precautions.
•
Do not attempt to adjust the driver’s seat while
the vehicle is moving.
2-1
SECTION 2 –
SAFETY AND PRECAUTIONS
•
•
•
•
•
•
Do not adjust tilt steering in a moving vehicle.
Do not operate the cruise control on icy or
extremely wet roads, winding roads, in heavy
traffic, or in any other traffic situation where
a constant speed cannot be maintained.
Use care when accelerating or decelerating on
a slippery surface. Abrupt speed changes can
cause skidding and loss of control.
Never drive the vehicle with a slideout room
extended.
Driving through water deep enough to wet the
brakes may affect stopping distance or cause
the vehicle to pull to one side. Check brake
operation in a safe area to be sure they have
not been affected. Never operate any vehicle if
a difference in braking efficiency is
noticeable.
Adverse weather conditions and extremes in
terrain may affect handling and/or
performance of your vehicle. Refer to your
chassis manual for complete and related
information on driving your vehicle.
WARNING
Do not fill propane container(s) to more
than 80 percent of capacity.
A properly filled container contains
approximately 80 percent of its volume as
liquid propane.
Overfilling propane container(s) can
result in uncontrolled propane flow, which
could lead to a fire or explosion and result
in death or serious injury.
WARNING
Do not place propane cylinders inside the
vehicle.
Propane cylinders are equipped with
safety devices that relieve excessive
pressure by discharging propane to the
atmosphere.
Propane gas is highly flammable.
Can lead to a fire or explosion and result
in death or serious injury.
FUEL AND PROPANE GAS
DANGER
All pilot lights, appliances, and their
ignitors (see operating instructions)
shall be turned off before refueling of
motor fuel tanks and/or propane
containers. Can cause ignition of
flammable vapors, which can lead to a
fire or explosion and result in death or
serious injury.
•
•
•
•
•
•
2-2
Do not place or store gasoline or other
flammable liquid containers inside the
vehicle.
All pilot lights must be extinguished and
appliances turned off while refilling the fuel
tank or propane gas tank.
Never smoke while refilling vehicle fuel tank
or propane gas tank.
Never use an open flame to test for propane
gas leaks. Replace all protective covers and
caps on propane system after filling. Make
sure valve is closed and the door is latched
securely.
Never connect natural gas to the propane gas
system.
When lighting range burners, do not turn
burner controls to “On” and allow gas to
escape before lighting match.
SECTION 2 –
SAFETY AND PRECAUTIONS
•
•
•
Portable fuel-burning equipment, including
wood and charcoal grills and stoves shall not
be used inside the recreational vehicle. The
use of this equipment inside the recreational
vehicle may cause fires or asphyxiation.
Propane gas regulators must always be
installed with the diaphragm vent facing
downward. Regulators are equipped with a
protective cover. Make sure that the regulator
vent faces downward and that the cover is kept
in place to minimize vent blockage, which
could result in excessive gas pressure causing
fire or explosion.
The following warning label is located in the
cooking area to remind you to provide an
adequate supply of fresh air for combustion.
asphyxiation is greater when the appliance is
used for long periods of time. Failure to comply
could result in death or serious injury.
PROPANE GAS LEAKS
Check propane gas system for leaks yearly, or
as necessary.
The following label is located in the vehicle
near the range area. If you smell gas within the
vehicle, quickly and carefully perform the
procedures listed.
DANGER
IF YOU SMELL PROPANE
DANGER
Do not use gas cooking appliances for
comfort heating. Can lead to carbon
monoxide poisoning, which can lead to
death or serious injury.
WARNING
Gas cooking appliances need fresh air for
safe operation.
Before operating:
Open vents or windows slightly or turn on
exhaust fan prior to using cooking
appliance. Gas flames consume oxygen,
which should be replaced to ensure
proper combustion. Improper use can
result in death or serious injury.
Unlike homes, the amount of oxygen supply is
limited due to the size of the recreational vehicle,
and proper ventilation when using the cooking
appliance(s) avoids dangers of asphyxiation. It is
especially important that cooking appliances not
be used for comfort heating, as the danger of
1. Extinguish any open flames and all
smoking materials.
2. Shut off the propane supply at the
container valve(s) or propane supply
connection.
3. Do not touch electrical switches.
4. Open doors and other ventilating
openings.
5. Leave the area until odor clears.
6. Have the propane system checked
and leakage source corrected before
using again.
Ignition of flammable vapors could lead to
a fire or explosion and result in death or
serious injury.
PROPANE GAS LEAK
DETECTOR
Your coach is equipped with a Propane Gas
Leak Detector, similar to the one shown below.
The leak detector sounds an alarm if an unsafe
amount of propane gas is present inside the
coach.
2-3
SECTION 2 –
SAFETY AND PRECAUTIONS
Further Information
See the manufacturer’s user guide provided in
your InfoCase for further instructions.
CARBON MONOXIDE ALARM
Propane Gas Leak Detector
WARNING
EXPLOSION HAZARD: DO NOT use an
open flame to test for gas leaks. When
testing for gas line leaks with a soapy
water solution, DO NOT use a detergent
containing ammonia or chlorine. These
substances may generate a chemical
reaction causing corrosion to gas lines,
resulting in dangerous leak conditions.
Death or serious injury can result.
Your coach is equipped with a Carbon
Monoxide (CO) Alarm, which has a sensor that is
designed to detect toxic carbon monoxide gas
fumes resulting from incomplete combustion of
fuel. It will detect CO gas from any combustion
source such as the furnace, gas range/oven, water
heater, refrigerator, chassis engine, and electric
generator engine.
To reduce the risk of carbon monoxide
poisoning, test this alarms operation after the
coach has been in storage, before each trip, and at
least once per week during use by pressing the
Test/Reset button on the alarm.
Push button
to test
Power Connection
The Propane Gas Leak Detector is powered by
the house batteries. If the House/Coach Battery
Disconnect switch is shut off or the battery cable
is disconnected from the batteries, the alarm will
not work. The Propane Gas Leak Detector fuse or
circuit breaker is located in the 12-volt house
electrical load center.
Because the Propane Gas Leak Detector is
connected to the house battery, it is always
drawing a small amount of current. Even though
this current draw is slight, it could drain the house
battery during storage periods when the house
battery will not be charged regularly by the
engine or shoreline.
Replacement
When replacing this alarm, we recommend
replacing only with the same model, or with one
that is also listed for RV application. We
recommend obtaining a replacement from your
Winnebago Industries® dealer.
2-4
Carbon Monoxide Alarm
WARNING
Failure to replace this product by the
“REPLACE BY DATE” printed on the
alarm cover may result in death by
Carbon Monoxide poisoning.
SECTION 2 –
SAFETY AND PRECAUTIONS
Replacement
When replacing this alarm, we recommend
replacing only with the same model, or with one
that is also listed for RV application. We
recommend obtaining a replacement from your
Winnebago Industries® dealer.
SMOKE ALARM
Your coach is equipped with a Smoke Alarm
(located on the ceiling in the lounge area.) The
Smoke Alarm is powered by a 9-volt battery and
has a sensor that is designed to detect smoke.
Further Information
Push button
to test
Please read the information provided by the
manufacturer, which is included in your InfoCase
for further information.
CARBON MONOXIDE
WARNING
WARNING
Avoid inhaling exhaust gases, as they
contain carbon monoxide, which is a
colorless, odorless, and poisonous gas.
Death or serious injury can result.
The best protection against carbon monoxide
entry into the vehicle body is a properly
maintained engine exhaust and ventilation
system. It is recommended that the exhaust
system and body be inspected by a qualified
motorhome service center:
• Each time the vehicle is serviced for an oil
change.
• Whenever a change in the sound of the
exhaust system is noticed.
• Whenever the exhaust system, underbody, or
rear of the vehicle is damaged.
To allow proper operation of the vehicle’s
ventilation system, keep front ventilation inlet
grill clear of snow, leaves, or other obstructions
at all times. DO NOT OCCUPY A PARKED
VEHICLE WITH ENGINE RUNNING FOR
AN EXTENDED PERIOD.
Do not run engine in confined areas, such as a
garage, except to move vehicle into or out of the
area.
Smoke Alarm
The following label is affixed to the Smoke
Alarm.
WARNING
Test smoke alarm operation after vehicle
has been in storage, before each trip, and
at least once per week during use. Failure
to do so can result in death or serious
injury.
Replacement
When replacing this alarm, we recommend
replacing only with the same model, or with one
that is also listed for RV application. We
recommend obtaining a replacement from your
Winnebago Industries® dealer.
Expiration and Further Information
See the manufacturer’s information in your
InfoCase for smoke alarm expiration and further
instructions.
2-5
SECTION 2 –
SAFETY AND PRECAUTIONS
FIRE EXTINGUISHER
ELECTRICAL
A dry chemical Fire Extinguisher is located
near the main entrance door.
•
Fire Extinguisher
(Typical installation your coach may vary
according to model and
floorplan)
•
•
We recommend that you become thoroughly
familiar with the operating instructions displayed
on the side of the Fire Extinguisher and in the
information supplied in your InfoCase.
We also recommend that you inspect the Fire
Extinguisher for proper charge at least once a
month in accordance with National Fire
Protection Association (NFPA)
recommendations as stated on the label.
If the extinguisher is past its expiration date or
charge is insufficient, the Fire Extinguisher must
be replaced.
•
•
•
LOADING
•
NOTICE
Do not test the fire extinguisher by
discharging it. Partial discharge can
cause leakage of pressure or contents,
which would render the unit inoperative
when needed. When using the fire
extinguisher, aim the spray at the base of
the fire.
Replacement
If for any reason you must replace the Fire
Extinguisher, the replacement must be the same
type and size as the one originally supplied in
your coach. We recommend obtaining a
replacement only from your Winnebago
Industries® dealer or a reliable RV parts supplier.
2-6
Careless handling of electrical components
can be fatal. Never touch or use electrical
components or appliances while feet are bare,
while hands are wet, or while standing in
water or on wet ground.
Improper grounding of the vehicle can cause
personal injury. Do not plug the utility power
cord into an outlet which is not grounded and
do not adapt the plug to connect to a receptacle
for which it is not designed.
Do not attach an extension cord to the utility
power cord.
Do not use any electrical device that has had
the ground pin removed.
Avoid overloading electrical circuits. Replace
fuses or circuit breakers with those of the
same size and amperage rating only. Never
use a higher rated fuse or breaker.
Use caution when handling or working near
electrical storage batteries. Always remove
jewelry and wear protective clothing and eye
covering. Avoid creating sparks.
•
•
Store or secure all loose items inside the
motorhome before traveling. Possible
overlooked items such as canned goods or
small appliances on the countertop, cooking
pans on the range, or free-standing furniture
items can become dangerous projectiles
during a sudden stop.
Be aware of GVWR, GAWR, and individual
load limit on each tire or set of duals (See
“Loading the Vehicle” in Section 12 Miscellaneous).
Never load the motorhome in excess of the
gross vehicle weight rating or the gross axle
weight rating for either axle.
SECTION 2 –
SAFETY AND PRECAUTIONS
MAINTENANCE
•
•
•
•
Do not remove the radiator cap while engine
and radiator are still hot. Always check
coolant level visually at the see-through
coolant reservoir.
Never get beneath a vehicle that is held up by
a jack only.
Do not mix different construction types of
tires on the vehicle, such as radial, bias, or
belted tires, as vehicle handling may be
affected. Replace tires with exact size, type,
and load range.
Refer to the chassis manual for complete
maintenance precautions and
recommendations.
Escape Window
(Lift both red safety latch handles UP and
push window OUT)
-Typical View
EMERGENCY EXITS
Escape Window
The escape window is secured by two red
safety latches at the bottom or side of the
window.
To open, lift both latches up and toward the
center of the window, then push outward near the
bottom of the window.
Escape Window
(Lift both red safety latch handles UP and
push window OUT)
-Typical View
Escape Window
(Lift both red safety latch handles UP and
push window OUT)
-Typical View
Escape Window
(Lift both red safety latch handles UP and
push window OUT)
-Typical View
Using Slider Windows As
Emergency Exits
Some coaches are required to have a slider
window as an alternate exit. This window will be
marked EXIT and have a red-handled latch.
2-7
SECTION 2 –
SAFETY AND PRECAUTIONS
WARNING
Keep all persons clear of the slideout
room and moving parts while extending or
retracting. Do not occupy the slideout
room while it is being extended or
retracted. Failure to observe can result in
death or serious injury.
Slider Window Latch
(Lift latch UP and slide window open)
-Typical View
Most slider windows along the side of any
motorhome can also be used as alternate
emergency exits, should the need arise.
To use slider windows as an exit:
• Lift window latch UP.
• Slide the window open.
• Either slide the screen open or push the screen
material out, depending on window
construction.
SLIDEOUT ROOMS
WARNING
Your motorhome may have more than
one slideout room. Understand which
switch operates which slideout room prior
to operation. Make sure all slideout rooms
are clear of people who could be harmed
or obstacles that could cause damage
prior to operating any slideout rooms.
Failure to observe can result in death or
serious injury.
Check inside and outside the vehicle to make
sure that there are no people who could be
harmed or obstacles that could cause damage due
to room activation.
2-8
FORMALDEHYDE
INFORMATION
Some of the materials used in this recreational
vehicle emit formaldehyde. Eye, nose, and throat
irritation, headache, nausea, and a variety of
asthma-like symptoms, including shortness of
breath have been reported as a result of
formaldehyde exposure. Reaction to
formaldehyde exposure may vary among
individuals. Elderly persons and young children,
as well as anyone with a history of asthma,
allergies, or lung problems may be at greater risk.
Research is continuing on the possible long-term
effects of exposure to formaldehyde. Inadequate
ventilation may allow formaldehyde and other
contaminants to accumulate in indoor air.
Ventilation to dilute the indoor air may be
obtained from a passive or mechanical
ventilation system. Always be sure to thoroughly
ventilate your recreational vehicle before and
during each use. High indoor temperatures and
humidity may raise formaldehyde levels. When a
recreational vehicle is in areas subject to high
temperatures, an air conditioning system can be
used to control indoor temperature levels. If you
have any questions regarding the health effects of
formaldehyde, consult your doctor or local health
department.
SECTION 2 –
SAFETY AND PRECAUTIONS
WARNING
This vehicle, like other vehicles, may
contain small amounts of one or more
substances which are listed by the state
of California for causing cancer or
reproductive toxicity.
MOLD, MOISTURE, AND YOUR
MOTORHOME
What is Mold?
Molds are part of the natural environment.
They are as old as the Earth itself and mold
spores are almost everywhere at some level
waiting to grow. Mold plays a part of nature by
breaking down dead organic matter, such as
fallen leaves and dead trees. Indoors however,
mold growth should be avoided. Molds
reproduce by means of tiny spores. Those spores
are invisible to the naked eye and float
throughout the outdoor and indoor air. Because
of the nature of the use of a motorhome, it is
natural for a motorhome to be introduced into an
environment with mold spores.
Mold is a plant and requires its own special
environment to grow. That environment includes
organic materials, nutrients, moisture, and proper
temperature.
How Can I Avoid Mold?
To reduce the ability for mold to grow, you
must reduce what constitutes its growth
environment. Mold can grow with the smallest of
a nutrient base. Just small amounts of dirt or dust
on the carpet can be enough to allow the mold
process to begin. Keep the environment as clean
as possible. Vacuum the carpet. Clean food spills
thoroughly and quickly. Avoid grease buildup
near the stove or sink. Clean the exhaust fan
above the stove often.
Minimize moisture in your motorhome and
keep humidity low. Clean spills quickly. Do not
allow condensation to build up. You can open
windows and vents to minimize condensation.
Use of the air conditioner can assist in removing
moisture from the air. Avoid leaks, but if leaks do
occur, make repairs promptly.
Avoid bringing mold into your motorhome.
Plants, cloths, books, and other household items
may already have mold present. It is easy to
transfer mold into your motorhome environment.
Monitor your motorhome. Periodically check
those hidden areas in corners, closets, and
cabinets to assure mold is not present.
What if I Find Mold?
If mold develops, clean the area with a
concentrate of soap and bleach. Items that
contain mold that cannot be cleaned should be
removed from the vehicle.
Can Mold Harm Me?
The effects of mold and airborne mold spores
may cause irritation to some people. Experts
disagree on the level of exposure that may cause
health concerns.
If Mold Is Present, What Will
Winnebago Industries® Do?
If Winnebago Industries determines that mold
is present in the motorhome as a result of a
manufacturing defect reported to Winnebago
Industries within the limited warranty period,
Winnebago will clean the affected area(s) and/or
replace affected items as it deems necessary. This
is the extent of coverage provided by Winnebago
Industries. Winnebago Industries, however, will
not assume responsibility for mold deemed to be
a result of a motorhome users lack of timely and
appropriate action to mitigate circumstances
should a problem occur.
If Winnebago Industries determines that mold
is present due to conditions it determines is not a
result of a manufacturing defect found within the
warranty period, Winnebago Industries will not
provide any financial assistance to the repair of
the condition.
2-9
SECTION 2 –
SAFETY AND PRECAUTIONS
ROOF AND LADDERS
•
–If Equipped
•
WARNING
•
STAY OFF ROOF. Surface may be
slippery. Falling could result in death or
serious injury.
The ladder on your motorhome is provided for
limited access to the roof.
Walking or working on the roof should be left
to qualified service personnel using proper safety
equipment in a safe environment. You should
only walk or work on the roof if you are qualified
and have created a safe environment.
For your safety, it is not recommended that
you store or carry items on the roof.
Before Using the Ladder
•
•
•
Inspect the ladder to make sure it is not
damaged. Never use a damaged ladder.
Keep the rungs of the ladder clean and dry
while in use. Never use the ladder when it is
raining, snowing, or icy. The rungs can
become slippery. Do not step onto the rungs if
the rungs are wet, or if your shoes are wet or
carry mud or debris that could result in a loss
of footing.
Never ignore warning labels or weight limits
defined on your ladder. The following
warning label is located on or near the ladder:
•
•
ROADSIDE EMERGENCY
Because of the size and weight of this vehicle
and its tires, and the possible complications
involved in tire changing, we strongly advise
obtaining professional road service to change a
flat tire whenever possible. However, if an
emergency requires you to change the tire
yourself, please exercise extreme caution and
read all tire changing information in the chassis
manual.
Never get beneath a vehicle that is held up by
a jack only.
If You Get A Flat Tire
•
•
•
WARNING
Do not exceed 225-lb. maximum weight
capacity. Misuse of ladder could result in
death or serious injury. See Operator’s
Manual before using ladder.
•
•
•
•
Maximum Capacity: 225 lbs.
Do not overload. Ladder is intended for one
person.
2-10
Make sure you are physically capable to
safely use the ladder. Strength, flexibility, and
stability are required.
Be aware that the vehicle may sway as you
climb the ladder. Do not use the ladder in high
winds.
As you climb the ladder, grasp the side rails
firmly and always use both hands. Keep your
body centered between the side rails. Do not
over-reach.
Never allow children on the ladder.
Do not transport items anchored to the
ladder. You could damage the ladder.
DO NOT panic.
Grip the steering wheel firmly and steer the
vehicle as straight as possible. Avoid quick
maneuvers. You may need to counter-steer to
compensate for “pull” created by the failed
tire.
DO NOT stomp on the brake. This abruptly
shifts the vehicle’s weight forward, making it
nose-dive and pull toward the blown-out side.
DO NOT jerk your foot off the accelerator.
Just ease back on the accelerator slowly and
gently to continue momentum. The deflated
tire will slow the vehicle.
If you must change lanes to get to a safe
stopping place, use your signals to warn other
motorists and change lanes smoothly and
carefully after you are certain the lane is clear.
SECTION 2 –
SAFETY AND PRECAUTIONS
•
Let the vehicle coast to a stop, gently steering
to a safe stopping place off the traffic lanes of
the road. Do not worry about damaging the
tire or wheel rim by driving on it. A tire or
wheel replacement is cheaper than damaging
the vehicle or injuring yourself.
• When you have come to a stop, activate your
hazard flashers to warn other motorists, then
exit the vehicle carefully.
• Set out flares or other warning devices.
Check your tires for proper inflation before
each trip and at least once a month with an
accurate tire gauge. See “Valve Stem Access” in
Section 3 - Driving Your Motorhome.
Spare Tire Storage
If your coach is supplied with a spare tire, it is
located in the rear storage compartment. Remove
wing nut from inside tire rim and lift or slide tire
out.
Some models, however, may have a swingdown spare tire carrier beneath the rear of the
coach. Please follow all safety warnings and
instructions for removing spare tire from the
carrier.
Swing-Down Carrier
–If Equipped
C AU T I ON
Do not lie beneath tire carrier while
removing tire. The tire can fall and injury
can occur.
•
•
•
•
•
Support tire carrier with a jack or block while
removing wire pin and wing nut from bolt at
back of carrier.
Carefully lower tire carrier to ground.
Remove 2 bolts and retainer plate that hold
wheel to carrier bracket.
Lift or slide tire from carrier.
Do not over-tighten wing nut when returning
carrier to storage position.
Recovery Towing
When calling a professional towing service,
we recommend that you advise them of your
coach length and approximate front axle weight
listed on your Vehicle Certification Label. This
will allow the towing operator to determine the
proper towing equipment to use.
Winnebago Industries® does not assume
responsibility for damage incurred while towing
this vehicle.
NOTE: Consult your chassis manual for towing
instructions or precautions provided by
the chassis manufacturer.
NOTICE
Do not lift on bumper. Damage will result
to front end body parts.
WARNING
Stay out from beneath the motorhome
while it is suspended by the towing
assembly. Do not allow passengers to
occupy a towed vehicle. Death or serious
injury can result.
JUMP STARTING
If your coach will not start from the chassis
battery, try using the Battery Boost switch to
divert power from the house batteries to the
starter. (See “Battery Boost Switch” in Section 3
- Driving Your Motorhome).
If you wish to try jump starting the engine
using another vehicle or booster system, see the
chassis manual for connecting jumper cables to
the automotive electrical system.
2-11
SECTION 2 –
SAFETY AND PRECAUTIONS
NOTICE
Do not attempt to push start this vehicle.
Damage to the transmission or other
parts of the vehicle will occur.
ENGINE OVERHEAT
If you see or hear steam escaping from the
engine compartment or have any other reason to
suspect an extreme engine overheating condition,
pull the vehicle over to the roadside as soon as it
is safe to do so, stop the engine, and get all
passengers out of the vehicle.
NOTICE
Operating a vehicle under a severe
overheating condition can result in
damage to the vehicle.
For information on what to do in case of
overheating, consult the chassis manual.
2-12
SECTION 3 – DRIVING YOUR MOTORHOME
The information in this section refers only to
features installed or adapted to the dash and
driver compartment area by Winnebago
Industries®. It also includes passenger seating in
the living area of the coach.
Folding Dinette Seat Back
Further Information
See the chassis manual in your InfoCase for
all original chassis related controls,
instrumentation, switches, and other features.
This includes items such as cruise control,
climate controls, gauges, wipers, lights, front
seats, and three-point safety belts, etc.
SEATS – DRIVER/CO-PILOT
The driver and co-pilot seats may be
independently adjusted to suit individual
preference.
•Unfasten the two snaps located behind the
dinette seat backrest cushion
•Fold-down the dinette seat backrest cushion
Further Information
See the chassis manual in your InfoCase for
instructions on seat adjustments.
5 - DASH / AUTO
FOLD-DOWN DINETTE SEAT
–If Equipped
(Models without front slideout and with dinette
seat directly behind driver or passenger front
seat)
On certain models, the dinette seat backrest
cushion (located directly behind the driver or
passenger front seat) must be folded down to
allow front seat reclining.
•Front seat can now be reclined
Typical view - your coach may vary according to
model and floorplan.
SEAT BELTS
Seats intended for occupancy while the
vehicle is in motion are equipped with seat belts
for the protection of the driver and passengers.
Lap Belts
The lap belts must be worn as low as possible
and fit snugly across the hip area. Always sit
erect and well back into the seat. To gain full
3-1
SECTION 3 –
DRIVING YOUR MOTORHOME
protection of the safety belt, never let more than
one person use the same safety belt at any one
time, and do not let the safety belts become
damaged by pinching them in the doors or in the
seat mechanism. After any serious accident, any
seat belts which were in use at the time must be
inspected and replaced if necessary.
WARNING
Snug and low belt positions are essential.
This will ensure that the force exerted by
the lap belt in a collision is spread over the
strong hip area and not across the
abdomen, which could result in serious
injury.
Only seats equipped with seat belts are to
be occupied while vehicle is in motion.
Swivel seats must be in the locked,
forward facing position while vehicle is in
motion.
1- Insert tab into buckle
slot until it “clicks” and is
locked
2- Pull strap to tighten
3- Press to
release
Adjustment:
To lengthen belt, swivel the tab end at a right
angle to belt and pull strap to desired length. To
shorten, pull loose end of belt.
To Fasten:
Be sure belt is not twisted. Grasp each part of
the belt assembly and push tongue into buckle.
Adjust to a snug fit by pulling the loose end away
from the tongue.
Lap/Shoulder Belts
Refer to the chassis manual provided in your
InfoCase for instructions on proper fastening,
adjustment, and releasing of lap/shoulder belts.
Seat Belt Care and Cleaning
•
•
•
To Release:
Press button in center of buckle and slide
tongue out of buckle.
•
Be careful not to damage the belt webbing and
hardware. Take care not to pinch them in the
seat or doors.
Inspect the belts and hardware periodically.
Check for cuts, frays, and loose parts.
Damaged parts should be replaced. Do not
remove or modify the belt system.
Keep belts clean and dry. If the belts need
cleaning, use only a mild soap and water
solution. Do not use hot water. Do not use
abrasive cleaners, bleach, or dyes. These
products may weaken the belts.
Replace any belt assembly that was used
during a severe impact. Replace the complete
assembly even if damage is not apparent.
CHILD RESTRAINTS
–If Equipped
A properly installed and secured child
restraint system can help reduce the chance or
severity of personal injury to a child in an
accident or during a sudden maneuver. Children
may have a greater chance of being injured in an
accident if they are seated in a child restraint
3-2
SECTION 3 –
DRIVING YOUR MOTORHOME
system which is not properly secured. Children
are always safer in the rear seats (behind the cab
area).
A child restraint system is designed to be
secured in a vehicle seat by a lap belt or the lap
belt portion of a lap-shoulder belt.
When purchasing a child restraint system,
follow these guidelines:
1. Look for the label certifying that it meets all
applicable safety standards.
2. Make sure that it will attach to your vehicle
and restrain your child securely and
conveniently so that you are able to install it
correctly each time it is used.
3. Be certain that it is appropriate for the child's
height, weight, and development. The
instructions and/or the regulation label
attached to the restraint typically provides this
information.
4. Review the instructions for installation and
use of the restraint. Be sure that you
understand them fully and can install the
restraint properly and safely in your vehicle.
1
2
3
1. Lower the dinette table.
2. Route the tether over the top of the dinette
seat back and hook it to the anchor loop on
the floor.
3. Fasten the lap belt.
-Typical View,
(Your coach may differ in appearance)
Further Information
See the child seat manufacturer’s specific
instructions for proper attachment and
adjustment of the tether and seat belts.
Tether Anchor Loop
–If Equipped
If your coach has a dinette, it may be equipped
with a child seat tether anchor loop located on the
floor or wall directly behind the forward facing
dinette seat.
KEYS
Your motorhome is supplied with several
keys. In addition to the chassis manufacturer’s
ignition key, you receive keys for the entrance
door and exterior compartment doors.
Keys have an identification number, either a
small metal tag or stamped into the key head.
These numbers are recorded on the vehicle’s
component model/serial sheet, which is included
in your InfoCase. In case keys are lost or stolen,
your dealer or a locksmith can provide you with
duplicate keys or modify the locks.
HAZARD WARNING FLASHERS
Tether Anchor Loop
NOTE: The dinette table must be in the lowered
position when a child seat is in use.
The hazard warning flashers provide
additional safety when the vehicle must be
stopped on the side of the roadway and presents a
possible hazard to other motorists. When the
flashers are on, it serves as a warning to other
drivers.
3-3
SECTION 3 –
DRIVING YOUR MOTORHOME
Further Information
Further Information
Refer to the chassis manual provided in your
InfoCase for instructions on activating,
operating, and canceling hazard warning
flashers.
Refer to the manufacturer’s user manual
provided in your InfoCase for further
information.
MIRRORS – MANUAL
SIDEVIEW EXTERIOR
–If Equipped
Always adjust mirrors for maximum rear
visibility before traveling. Make sure the seat is
adjusted for proper vehicle control and that you
are sitting back squarely into the seat.
MIRRORS – POWER SIDEVIEW
EXTERIOR
–If Equipped
Always adjust mirrors for maximum rear
visibility before traveling. Make sure the seat is
adjusted for proper vehicle control and that you
are sitting back squarely into the seat.
The mirrors may also contain heating
elements to de-fog or de-ice the mirror glass
during cold weather operation. An ON-OFF
switch for the mirror heaters is located near the
remote mirror controls.
The ignition switch must be on to operate
mirror controls and heaters.
Mirror Heat
Switch
•The mirrors can be folded back against the cab
doors, if needed.
Mirror Head Adjustment
Mirror Adjustment Control
•Mirror surface tilts in direction of arrow button
pressed.
•Middle switch selects L or R mirror to adjust.
•Center position is “neutral” to disable arrow
buttons and prevent misadjustment of mirrors.
Adjustment Screw
•Loosen screw to pivot mirror head, then
retighten screw
3-4
SECTION 3 –
DRIVING YOUR MOTORHOME
BATTERY BOOST SWITCH
The Battery Boost switch can be used to draw
emergency starting power from the house
batteries to start the engine if the chassis battery
is discharged.
Press and Hold the Battery Boost switch in the
ON position while turning ignition key for
emergency starting power.
•The mirrors can be folded back
against the cab doors, if needed.
Sideview Camera
NOTE: The House/Coach Battery Disconnect
switch near the entrance door must be
ON and house batteries must be
sufficiently charged for this feature to
work.
–If Equipped
The sideview cameras (built into the driver
and passenger side mirrors) activate with the
corresponding turn signals and replace the rear
camera view on the monitor until the turn is
completed or the signal lever is canceled
manually.
Battery Boost Switch
(Typical View - depending on model)
•If chassis battery is discharged, press and hold
while turning ignition key for emergency starting
power.
AIR CONDITIONER/HEATER –
AUTOMOTIVE (DASH)
•Sideview Camera
Mirror Head Adjustment
If you cannot adjust a mirror properly using
the control switch, the mirror may need a coarse
adjustment by rotating the mirror head.
See the chassis manual for operating
information on driver and passenger comfort
controls – air conditioner, heater, defroster, and
ventilation.
NOTE: The dash air conditioner is not designed
to cool the entire interior of the coach,
but is intended only to provide cooling
for the cab area.
Further Information
Refer to the manufacturer’s user manual
provided in your InfoCase for further
information.
3-5
SECTION 3 –
DRIVING YOUR MOTORHOME
RADIO IN-DASH/REARVIEW
MONITOR SYSTEM
screen. Press and hold to switch to the camera
view mode. For MUTE: Press to switch the
mute setting to on or off.
(6) TRACK - Performs manual seek tuning,
fast forward, reverse and track search
controls.
(7) EJECT - Press to eject the CD/DVD.
(8) RESET.
(9) DISC LOADING SLOT
–If Equipped
The radio in your coach can receive AM/FM
stereo stations. It also has a CD/DVD player for
your listening enjoyment through quality highoutput speakers located in several areas of the
coach.
This system is also featured with a rearview
camera monitor system, which lets you see what
is directly behind your coach for safety and
maneuvering assistance. The viewing screen is
integrated into the dash.
The radio screen switches automatically when
the transmission is shifted into reverse.
•
NOTE: The camera polarity setting needs to be
set to “Battery” for automatic camera
viewing when the vehicle is put into
reverse. The “Camera Polarity” setting
is found under “Camera Settings” in the
system menu.
–If Equipped
The sideview cameras (built into the driver
and passenger side mirrors) activate with the
corresponding turn signals and replace the rear
camera view on the monitor until the turn is
completed or the signal lever is canceled
manually.
•
•
•
NOTE: When parked the Radio Power switch
should be set to “HOUSE”, make sure
the park brake is set prior to turning the
vehicle off or the radio may not play
DVDs.
Sideview Cameras
Satellite Radio
–If Equipped
Your coach may be equipped with a
SiriusXM® satellite radio receiver that plays
through your radio.
See the receiver manufacturer’s information
in your InfoCase for programming and operating
instructions.
USB Cable
Basic Operating Instructions
•
•
•
•
•
3-6
(1) LCD Screen.
(2) +/- VOLUME - Press to set the volume.
(3) DISPLAY - Press to turn the display on or
off.
(4) TOP MENU - Press to switch the display
between the top menu screen and the current
source screen.
(5) MODE or MUTE (depending on model)
- For MODE: Press to switch between the
Application screen and the AV operation
–If Equipped
Your coach may be equipped with a cable to
connect your USB (located in the beverage tray)
to play through your radio.
SECTION 3 –
DRIVING YOUR MOTORHOME
•
To remove engine cover, unlatch the two
upper and the two lower latches (located on
each side of the engine cover).
USB Cable
(Located in the beverage tray)
-Typical Installation
See the manufacturer’s information in your
InfoCase for operating instructions.
Bluetooth
–If Equipped
Your coach may be equipped with a Bluetooth
microphone cable for hands-free cell phone
usage. The microphone cable is located in the
beverage tray.
See the manufacturer’s information in your
InfoCase for operating instructions.
Radio Remote Control
A hand-held remote control for the radio lets
you control the radio from a distance for your
convenience. The remote control is included in
your InfoCase.
Further Information
See the manufacturer’s user guide provided in
your InfoCase for complete operating
instructions.
ENGINE ACCESS – INTERIOR
Front Engine Cover
NOTE: Take precautions to protect carpet and
interior furnishings when removing
engine cover. The underside of the engine
cover could contain deposits of oil and
fuel or other engine fluids and
substances that could damage fabrics
and interior furnishings.
Front Engine Latches
-Typical View
ENGINE COOLING SYSTEM
Do not remove the radiator cap while engine
and radiator are still hot. Always check coolant
level visually at the see-through coolant
reservoir.
NOTE: Your chassis engine cooling system is
filled with special extended-life coolant
that is not the same as common antifreeze available at retail outlets.
The coolant system MUST be refilled or
topped up with the same type of coolant
as equipped to maintain the special longlife properties.
Further Information
Refer to the chassis manual in your InfoCase
for information and precautions on filling,
servicing, and checking the fluid level.
TIRES
Improper tire pressure can result in tire
overloading and abnormal wear and also affects
handling, ride characteristics, and fuel economy.
3-7
SECTION 3 –
DRIVING YOUR MOTORHOME
WARNING
Make sure all replacement tires are of the
same size and rating as those shown on
your Vehicle Certification Label.
SUSPENSION ALIGNMENT
AND TIRE BALANCE
The front suspension and steering system of
this vehicle was factory aligned using highly
accurate equipment prior to delivery to the
dealership. However, alignment should be
checked and adjusted after you have fully loaded
the motorhome according to your personal needs.
Thereafter, the alignment should be periodically
inspected to help prevent uneven tire wear.
Any excessive or abnormal tire wear may
indicate worn or misaligned suspension or
steering, unbalanced tire, or other tire/suspension
problem.
Alignment can be affected by worn steering/
suspension parts or by incidents which happen
during driving, such as hitting a curb, pothole, or
railroad track, etc. Improper alignment can cause
tires to roll at an angle and wear unevenly. It may
also cause the vehicle to “pull” to the right or left.
Have your dealer inspect your vehicle’s
suspension and steering components periodically
for misalignment or wear.
Out-of-balance tires will not roll smoothly and
can lead to vibrations and uneven tread wear,
such as cupping and flat spots. Tires may need to
be balanced if uneven wear is detected or if ride
comfort decreases noticeably.
AIR SPRINGS – REAR HELPER
(AIR BAGS)
–If Equipped
The rear air helper springs (air bags) are an
enhancement to the standard suspension system
to provide adjustable load and ride conditions.
This feature is not intended to increase the load
capacity of the rear axle or vehicle.
Adjustment
Check and adjust the air bag pressure
periodically to maintain optimal ride and
handling characteristics according to cargo
weight.
Too much air pressure in the air helper springs
will result in a firmer ride, while too little air
pressure will allow the air helper spring to bottom
out over rough road conditions. Too little air
pressure will also not provide the improvement in
handling that is possible.
The air bags can be adjusted independently if
necessary to equalize a load, however, we
recommend maintaining the same pressure in
both air bags whenever possible to ensure that the
vehicle remains level.
Recommended Pressure
Minimum Air Pressure . . . . . . . . . . .20 psi
Maximum Air Pressure . . . . . . . . . . .80 psi
Air Spring
Further Information
Refer to the chassis manual provided in your
InfoCase for further information.
Rear Air Spring Valves
•Models 26A, 31D, 31K: Located inside left rear
wheel well
•Model 31G: Located inside right rear wheel well
-Typical View
3-8
SECTION 3 –
DRIVING YOUR MOTORHOME
LIGHTS
All exterior lights should be checked for
proper operation each time the vehicle is
prepared for a trip. Any bulbs which fail to light
should be checked and replaced, when necessary,
with a new bulb of the same size. A failure of
more than one light, such as both taillights not
operating, may indicate a burned out fuse. Check
fuse and replace with one of the same rating
when necessary. If a fuse is not the cause of the
problem, the wiring system should be checked
immediately by an authorized service center.
Further Information
Refer to the chassis manual in your InfoCase
for further information.
3-9
SECTION 4 – APPLIANCES AND SYSTEMS
The appliances installed in your motorhome
are manufactured by reputable RV appliance
makers and have been tested by independent
laboratories to meet all applicable standards and
codes set for RV appliances.
See Section 2 - Safety and Precautions of this
manual for any safety and precautions you need
to take regarding the operation of your
appliances.
Leveling
Before operating the refrigerator when the
motorhome is stationary, place a small level on
the bottom of the refrigerator and make certain
the unit is level. If over 1/2 of the bubble is inside
the circle in any direction, the coach is level
enough for continuous operation of the
refrigerator while parked.
REFRIGERATOR
WARNING
Do not let children play inside the
motorhome unattended. Unlike your
home refrigerator/freezer that one could
push open the door from the inside, your
motorhome refrigerator has a travel latch
and when engaged would trap a child
inside resulting in suffocation leading to
death or serious injury.
Place bubble level in bottom of refrigerator
Bubble must be at least 1/2 inside circle
Normal vehicle leveling to provide comfort
for the occupants is satisfactory for refrigerator
operation.
NOTICE
The refrigerator is made to operate within
3 off level side-to-side and 6 off level
front-to-back (as looking at the front of the
refrigerator). Operating it at more than
these limits can cause damage to the
cooling system. Make sure the vehicle is
level before you operate the refrigerator.
4-1
5 - DASH / AUTO
–If Equipped
The refrigerator in your coach can operate
from either of two energy sources available to the
motorhome:
• 120-Volt AC Electric
• Propane Gas
To be able to use both types of energy, the
refrigerator does not have a compressor like
household refrigerators. Instead, it uses an
ammonia-water solution for cooling. Basically,
ammonia vapor is distilled from the solution by
heat produced from either propane gas flame or
electrical heat element. The ammonia vapor is
then carried to the finned condenser where it
liquefies. The liquid then flows to an evaporator
where it creates cooling by evaporation. The
ammonia circulates back into the water solution
and the cooling cycle continues.
SECTION 4 –
APPLIANCES AND SYSTEMS
Basic Operation
Slide the control switches to the operating
positions described and observe the indicator
lights.
•
•
•
•
•
Gas- Refrigerator will operate on gas from the
propane tank if the main valve is open and the
tank contains gas.
Auto- Refrigerator will operate on 120-VAC
household current if the shoreline is
connected or the auxiliary generator is
running. If electricity is lost, it will
automatically switch over to Gas operation if
gas is available.
Temperature Setting- Start at the coldest
setting to ensure coldest temperature in the
freezer compartment, then adjust warmer as
necessary after cold* food has been added.
“On” Indicator Light- Glows steady when
refrigerator is operating properly.
“Gas” Indicator Light- Will flash if gas is
not available. To operate the refrigerator you
must provide 120VAC then switch to Auto
operation.
NOTE: The refrigerator will retain temperature
more efficiently if food is cold before
placing inside.
Further Information
Refer to the manufacturer’s user guide
provided in your InfoCase for complete operating
instructions, safety precautions, and maintenance
information.
4-2
REFRIGERATOR
–If Equipped
The refrigerator in your coach can operate
from either of two energy sources available to the
motorhome:
• 120-Volt AC Electric
• Propane Gas
To be able to use both types of energy, the
refrigerator does not have a compressor like
household refrigerators. Instead, it uses an
ammonia-water solution for cooling. Basically,
ammonia vapor is distilled from the solution by
heat produced from either propane gas flame or
electrical heat element. The ammonia vapor is
then carried to the finned condenser where it
liquefies. The liquid then flows to an evaporator
where it creates cooling by evaporation. The
ammonia circulates back into the water solution
and the cooling cycle continues.
WARNING
Do not let children play inside the
motorhome unattended. Unlike your
home refrigerator/freezer that one could
push open the door from the inside, your
motorhome refrigerator has a travel latch
and when engaged would trap a child
inside resulting in suffocation leading to
death or serious injury.
Leveling
Before operating the refrigerator when the
motorhome is stationary, place a small level on
the bottom of the refrigerator and make certain
the unit is level. If over 1/2 of the bubble is inside
the circle in any direction, the coach is level
enough for continuous operation of the
refrigerator while parked.
SECTION 4 –
APPLIANCES AND SYSTEMS
•
Place bubble level in bottom of refrigerator
•
Bubble must be at least 1/2 inside circle
Normal vehicle leveling to provide comfort
for the occupants is satisfactory for refrigerator
operation.
•
NOTICE
The refrigerator is made to operate within
3 off level side-to-side and 6 off level
front-to-back (as looking at the front of the
refrigerator). Operating it at more than
these limits can cause damage to the
cooling system. Make sure the vehicle is
level before you operate the refrigerator.
Basic Operation
•
Press the MODE button to select energy
source. There are three settings:
LP Gas Mode - Refrigerator will operate on
gas from the propane tank if the main valve is
open and the tank contains gas.
Electric Mode - Refrigerator will operate on
120-VAC household current if the shoreline is
connected or the auxiliary generator is
running.
Automatic Mode - Refrigerator will
automatically start operating on 120-VAC
household current if the shoreline is
connected or the auxiliary generator is
running. If electricity is lost, it will
automatically switch over to LP gas operation
if gas is available.
Press the TEMP SET button to change
temperature setting from 1 (warmest setting)
to 5 (coldest setting).
Start at the ‘coldest’ setting to ensure coldest
temperature in the freezer compartment, then
adjust warmer as necessary after cold food has
been added.
“On” Indicator Light- Glows steady when
refrigerator is operating properly.
“Gas” Indicator Light- Will flash if gas is
not available. To operate the refrigerator you
must provide 120VAC then switch to Auto
operation.
NOTE: The refrigerator will retain temperature
more efficiently if food is cold before
placing inside.
Further Information
Refer to the manufacturer’s user guide
provided in your InfoCase for complete operating
instructions, safety precautions, and maintenance
information.
REFRIGERATOR
•
Press the ON/OFF button to start the
refrigerator.
–If Equipped
The refrigerator in your coach can operate
from either of two energy sources available to the
motorhome:
• 120-Volt AC Electric
• Propane Gas
4-3
SECTION 4 –
APPLIANCES AND SYSTEMS
To be able to use both types of energy, the
refrigerator does not have a compressor like
household refrigerators. Instead, it uses an
ammonia-water solution for cooling. Basically,
ammonia vapor is distilled from the solution by
heat produced from either propane gas flame or
electrical heat element. The ammonia vapor is
then carried to the finned condenser where it
liquefies. The liquid then flows to an evaporator
where it creates cooling by evaporation. The
ammonia circulates back into the water solution
and the cooling cycle continues.
Bubble must be at least 1/2 inside circle
Normal vehicle leveling to provide comfort
for the occupants is satisfactory for refrigerator
operation.
WARNING
NOTICE
Do not let children play inside the
motorhome unattended. Unlike your
home refrigerator/freezer that one could
push open the door from the inside, your
motorhome refrigerator has a travel latch
and when engaged would trap a child
inside resulting in suffocation leading to
death or serious injury.
Leveling
Before operating the refrigerator when the
motorhome is stationary, place a small level on
the bottom of the refrigerator and make certain
the unit is level. If over 1/2 of the bubble is inside
the circle in any direction, the coach is level
enough for continuous operation of the
refrigerator while parked.
The refrigerator is made to operate within
3 off level side-to-side and 6 off level
front-to-back (as looking at the front of the
refrigerator). Operating it at more than
these limits can cause damage to the
cooling system. Make sure the vehicle is
level before you operate the refrigerator.
Basic Operation
•
•
Place bubble level in bottom of refrigerator
-Typical View
•
4-4
Press the ON/OFF button to start the
refrigerator.
If the display code reads “no” there is no
electricity or gas available to operate the
refrigerator. Open the propane tank valve or
connect the shoreline.
Press the MODE button to select energy
source. There are three settings:
LP (Gas Mode) - Refrigerator will operate on
SECTION 4 –
APPLIANCES AND SYSTEMS
•
gas from the propane tank if the main valve is
open and the tank contains gas.
AC (Electric Mode) - Refrigerator will
operate on 120-VAC household current if the
shoreline is connected or the auxiliary
generator is running.
AU (Automatic Mode) - Refrigerator will
automatically start operating on 120-VAC
household current if the shoreline is
connected or the auxiliary generator is
running. If electricity is lost, it will
automatically switch over to LP gas operation
if gas is available.
Press the TEMP SET button to change
temperature setting from 1 to 9 on display.
Start at the ‘coldest’ setting to ensure coldest
temperature in the freezer compartment, then
adjust warmer as necessary after cold food has
been added.
NOTE: The refrigerator will retain temperature
more efficiently if food is already cold
before placing inside.
Further Information
Refer to the manufacturer’s user guide
provided in your InfoCase for complete operating
instructions, safety precautions, and maintenance
information.
where it creates cooling by evaporation. The
ammonia circulates back into the water solution
and the cooling cycle continues.
WARNING
Do not let children play inside the
motorhome unattended. Unlike your
home refrigerator/freezer that one could
push open the door from the inside, your
motorhome refrigerator has a travel latch
and when engaged would trap a child
inside resulting in suffocation leading to
death or serious injury.
Leveling
Before operating the refrigerator when the
motorhome is stationary, place a small level on
the bottom of the refrigerator and make certain
the unit is level. If over 1/2 of the bubble is inside
the circle in any direction, the coach is level
enough for continuous operation of the
refrigerator while parked.
REFRIGERATOR
–If Equipped
The refrigerator in your coach can operate
from either of two energy sources available to the
motorhome:
• 120-Volt AC Electric
• Propane Gas
To be able to use both types of energy, the
refrigerator does not have a compressor like
household refrigerators. Instead, it uses an
ammonia-water solution for cooling. Basically,
ammonia vapor is distilled from the solution by
heat produced from either propane gas flame or
electrical heat element. The ammonia vapor is
then carried to the finned condenser where it
liquefies. The liquid then flows to an evaporator
Place bubble level in bottom of refrigerator
Bubble must be at least 1/2 inside circle
4-5
SECTION 4 –
APPLIANCES AND SYSTEMS
Normal vehicle leveling to provide comfort
for the occupants is satisfactory for refrigerator
operation.
•
NOTICE
The refrigerator is made to operate within
3 off level side-to-side and 6 off level
front-to-back (as looking at the front of the
refrigerator). Operating it at more than
these limits can cause damage to the
cooling system. Make sure the vehicle is
level before you operate the refrigerator.
Basic Operation
•
•
Press the ON/OFF button to start the
refrigerator.
If the display code reads “no” there is no
electricity or gas available to operate the
refrigerator. Open the propane tank valve or
connect the shoreline.
running. If electricity is lost, it will
automatically switch over to LP gas operation
if gas is available.
Press the TEMP SET button to change
temperature setting from 1 to 9 on display.
Start at the ‘coldest’ setting to ensure coldest
temperature in the freezer compartment, then
adjust warmer as necessary after cold food has
been added.
NOTE: The refrigerator will retain temperature
more efficiently if food is already cold
before placing inside.
Further Information
Refer to the manufacturer’s user guide
provided in your InfoCase for complete operating
instructions, safety precautions, and maintenance
information.
REFRIGERATOR SERVICE
ACCESS COMPARTMENT
(Exterior)
–If Equipped
The exterior refrigerator service compartment
allows access to the rear of the refrigerator for
inspection, maintenance, and service.
To Open
-Typical View
•
4-6
Press the MODE button to select energy
source. There are three settings:
LP (Gas Mode) - Refrigerator will operate on
gas from the propane tank if the main valve is
open and the tank contains gas.
AC (Electric Mode) - Refrigerator will
operate on 120-VAC household current if the
shoreline is connected or the auxiliary
generator is running.
AU (Automatic Mode) - Refrigerator will
automatically start operating on 120-VAC
household current if the shoreline is
connected or the auxiliary generator is
1. Use a screwdriver or coin to turn the latch
knobs to the vertical position as shown.
2. Remove the door from the opening.
To Close
1. Replace the door into the opening.
2. Push the latch knobs in while turning to the
horizontal position as shown.
SECTION 4 –
APPLIANCES AND SYSTEMS
Glass Range Cover - lift
cover before igniting range.
•CLOSED
•OPEN
Refrigerator Access Door Latches
-Typical View
REFRIGERATOR (EXTERIOR)
–If Equipped
Your coach may be equipped with an exterior
refrigerator which is included in the optional
tailgate package. If equipped, the refrigerator is
located in the passenger side rear storage
compartment.
Further Information
See the appliance manufacturer’s user guide
provided in your InfoCase for complete operating
instructions, safety precautions, and maintenance
care.
RANGE AND OVEN WITH
GLASS RANGE COVER
–If Equipped
NOTE: See the appliance manufacturer’s user
guide provided in your InfoCase for
complete operating instructions and
safety precautions.
The Range and optional Oven in your motor
home operate on propane gas and will provide
most of the functions of the range in your home.
To Light Range Top Burners
• Lift glass range cover.
• Depress the desired burner knob and turn
counter-clockwise to the ON or LITE position
(do NOT attempt to light more than one
burner at a time).
• Turn the SPARK knob, you will hear the
igniter “click”.
NOTE: If the burner does not light within about
ten seconds or if the flame should go out
during cooking, turn the burner off. If
gas has accumulated and a strong gas
odor is detected, open a window and wait
5 minutes for the gas odor to disappear
before relighting the burner.
•
If the appliance has not been operated
for a period of time, the surface burner
may be difficult to light due to air in the
gas line.
To extinguish the burner flame, turn desired
burner knob to OFF.
4-7
SECTION 4 –
APPLIANCES AND SYSTEMS
NOTICE
Do not store items in oven.
If oven would turn on stored items can
ignite resulting in fire and or property
damage.
Oven Burner Knob
(If Equipped)
-Typical View
•
•
PILOT ON position keeps pilot flame lit for
repeated use of Oven while vehicle is parked.
Turn Oven knob to PILOT OFF position
while traveling or refilling propane gas tank.
To Light Oven Pilot
See “Oven Operation” in the manufacturer’s
user guide provided in your InfoCase.
Avoiding Asphyxiation
The following warning label has been located
in the cooking area to remind you to provide an
adequate supply of fresh air for combustion.
DANGER
Do not use gas cooking appliances for
comfort heating. Can lead to carbon
monoxide poisoning, which can lead to
death or serious injury.
4-8
WARNING
Gas cooking appliances need fresh air for
safe operation.
Before operating:
Open vents or windows slightly or turn on
exhaust fan prior to using cooking
appliance. Gas flames consume oxygen,
which should be replaced to ensure
proper combustion. Improper use can
result in death or serious injury.
Unlike homes, the amount of oxygen supply is
limited due to the size of the recreational vehicle,
and proper ventilation when using the cooking
appliances avoids dangers of asphyxiation.
It is especially important that cooking
appliances not be used for comfort heating, as the
danger of asphyxiation is greater when the
appliance is used for long periods of time.
FAILURE TO COMPLY COULD RESULT
IN DEATH OR SERIOUS INJURY.
WARNING
Portable fuel-burning equipment
including wood and charcoal grills and
stoves, shall not be used inside the
recreational vehicle. The use of this
equipment inside the recreational vehicle
can cause fires or asphyxiation. Failure to
comply could result in death or serious
injury.
NOTICE
Turn off the range and allow it to cool
before closing the range cover. The range
cover is made of glass and may shatter
when heated.
SECTION 4 –
APPLIANCES AND SYSTEMS
MICROWAVE OVEN
SYSTEMS MONITOR PANEL
–If Equipped
Refer to the manufacturer’s user guide located
inside the appliance for complete operating
instructions.
The Systems Monitor Panel provides a
convenient central location for checking the
condition of all utility systems in your coach.
NOTICE
Do not store items in oven.
If oven would turn on stored items can
ignite resulting in fire and or property
damage.
MICROWAVE/CONVECTION
OVEN
–If Equipped
Refer to the manufacturer’s user guide located
inside the appliance for complete operating
instructions.
NOTICE
Do not store items in oven.
If oven would turn on stored items can
ignite resulting in fire and or property
damage.
At the touch of a button this panel will display
the fresh water and holding tank levels, propane
gas tank level, plus the house battery condition.
You can start the generator or turn on the water
pump and water heater. Indicator lights tell you if
the water pump is on or if the water heater pilot
light is out.
Water And Holding Tank Levels
RANGE HOOD
–If Equipped
The range hood vent draws cooking odors and
airborne grease particles into the filtration grid
and either recirculates the air or vents it to the
outside of the coach, depending on model.
A light on the underside of the hood provides
illumination for cooking and food preparation.
Press and Hold the Levels Test switch to show
approximate level on the monitor lights.
Further Information
See the manufacturer’s user guide provided in
your InfoCase for instructions on replacement of
light bulbs and replacement or cleaning of grease
filter elements.
4-9
SECTION 4 –
APPLIANCES AND SYSTEMS
The approximate fluid levels are measured by
electronic sensors on the sides of the tanks. There
is generally more fluid in a tank than indicated on
the monitor panel.
Sensors
•
•
Yellow - marginal charge.
Red - battery needs charging before use.
To get an accurate reading:
1. Both the chassis engine and the generator
engine must be shut off and 120-volt AC
shoreline unplugged.
2. An interior light should be turned on to
provide a small load which draws off the
battery surface charge.
Water Pump Switch
For example, if the fluid level is 1-2” below
the FULL sensor, the monitor will show the level
to be only 2/3 even though the tank is nearly full.
If a tank is about 1/4 full, the monitor will
register an empty tank because the fluid level is
below the 1/3 sensor even though there is still
fluid in the tank.
However, when the indicator reads FULL, the
tank is actually full.
When use of the self-contained water system
is desired, turn the Water Pump switch on. The
“Pump On” light will illuminate when the pump
switch is on and the system is operable. Water
will be available as soon as a faucet is opened.
Refer to the Water Pump information
elsewhere in this section for additional
information on the water pump and initial startup.
Tank Capacities
See “Tank Capacities” in Section 1 Introduction.
Propane Gas Level
Press and Hold the Levels Test switch to show
approximate propane tank level.
The propane level is registered by a sending
unit on the tank. The gauge mounted on the side
of the tank will give a more accurate indication of
actual tank level if needed.
Battery Charge Meter
Press and Hold the Levels Test switch to
check the level of charge (voltage) in the 12-volt
house battery.
The colored segments (red, yellow, and green)
will light from the bottom up to the amount of
charge the battery contains.
• Green - good or adequate charge.
4-10
NOTE: Some models may be equipped with a
Water Pump switch in the water service
center on the outside of the coach or
within the bathroom area for your
convenience.
WATER HEATER – GAS
–If Equipped
NOTE: Read the Water Heater operating guide
provided in your InfoCase for complete
operating instructions, safety warnings,
and maintenance information before
operating the Water Heater.
SECTION 4 –
APPLIANCES AND SYSTEMS
Ensure the Water Heater is filled with
water before operating.
To fill the Water Heater, turn the Water Pump
switch ON and open a hot water faucet anywhere
in the coach. When water begins to flow steadily
from the faucet, the Water Heater is full.
Propane Gas Operation
•
Press the Water Heater switch (located on the
Systems Monitor Panel) to the ON position.
NOTE: Read the Water Heater Operation
Manual for complete Safety Warnings,
Operating Instructions, and
Maintenance Information before
operating the water heater.
Be sure the water heater is filled with water
before starting either electric or propane gas
operation. To fill the water heater, turn the
Water Pump switch on and open a hot water
faucet anywhere in the coach. When water begins
to flow steadily from the faucet, the water heater
is full.
For Propane Gas Operation
•
•
The “Pilot Out” light will glow for about 1015 seconds, then it will go out. The “Heater
On” indicator will remain lit.
If the “Pilot Out” light comes on during
operation, it means that the burner has gone
into “lockout” mode and must be restarted. If
this happens, turn the Water Heater switch
OFF for approximately 5 minutes, then turn
back on.
Press the Water Heater switch on the Systems
Monitor Panel. The “Pilot Out” light will glow
for about 10-15 seconds, then it will go out. The
“Heater On” indicator will remain lit. If the “Pilot
Out” light comes on during gas operation, it
means that the burner has gone into “lockout”
mode and must be restarted. If this happens, turn
the Water Heater switch off for about 5 minutes,
then turn it back on.
Further Information
See the Water Heater manufacturer’s
operation manual provided in your InfoCase for
complete operating instructions, safety warnings,
and maintenance information.
WATER HEATER – GAS/
ELECTRIC
–If Equipped
The gas/electric water heater has a dual power
feature. It can operate from propane gas or 120volt house current; or it can use both at the same
time for quicker recovery at times when you are
using a lot of hot water.
Gas Water Heater Switch
(Located on Systems Monitor Panel)
For Electric Operation
Turn on the Water Heater electric element
switch. The shoreline must be connected or
generator running for electric operation.
4-11
SECTION 4 –
APPLIANCES AND SYSTEMS
Electric Water Heater Switch
(Typically located near Systems
Monitor Panel)
For Quick Recovery Operation
(Dual Heating)
Turn On both Water Heater switches - the gas
one on the monitor panel and the electric one.
This will help reheat the water heater tank more
quickly than a single source would alone. Use
this mode when you are using a larger than
normal volume of hot water.
Further Information
See the Water Heater manufacturer’s
operation manual provided in your InfoCase for
complete operating instructions, safety warnings,
and maintenance information.
PRESSURE-TEMPERATURE
RELIEF VALVE
On occasion, water may be seen seeping from
the water heater pressure temperature relief
valve. This is no cause for repair or replacement
of the valve.
4-12
Water Heater Exterior Service Access
Normally there is an air gap at the top of the
water heater tank, which acts as a pressure buffer.
In time, however, heated water may expand and
fill this air gap, causing a slight increase in water
pressure. This may cause the P-T valve to “weep”
until the air gap is manually replaced.
C AU T I ON
Hot water can escape from tank causing
injury. Operate this valve only when the
tank water is cold.
To Replace the Air Gap:
1. Turn off the Water Heater switch and
incoming water supply (city water and/or
demand pump).
2. Open a faucet in the motorhome to relieve
water pressure.
3. Pull the handle of the P-T valve straight out
and allow water to flow until it stops.
SECTION 4 –
APPLIANCES AND SYSTEMS
•Lift handle straight out to open P-T valve
when water heater is cold.
4. Let the handle of the P-T valve snap shut.
5. Close the faucet and turn on the water supply
before switching the water heater on.
Manually operate the pressure temperature
relief valve at least once a year.
NOTE: If your water heater is equipped with the
motoraid system, it uses an extension
from the engine cooling system to heat
water in the water heater while driving.
The engine cooling system must also be
cold before opening the pressuretemperature relief valve. See “Motoraid
Water Heater” for more information.
FURNACE – PROPANE GAS
–If Equipped
To Start Up
1. Open the LP gas tank valve by turning fully
counter-clockwise.
Temp Selector
•Slide to select temperature
2. Move SYSTEM switch from Off to Heat and
set the desired temperature using the Temp
Selector slider.
3. Furnace fan should start to blow immediately
after setting the thermostat.
4. After about 30 seconds, the furnace burner
should light.
5. The furnace should now cycle off and on
automatically as the thermostat demands just
like a household furnace.
NOTE: If heat does not come out of the heat
ducts after a minute or so the burner is
not lit.
Turn thermostat off for 3-5 minutes,
check to be sure propane gas tank valve
is open and tank is not empty, then try
steps 2-4 again.
If the furnace will not light after three
attempts, go to Shut Down steps and
contact your dealer or a local RV service
center for repair.
To Shut Down
1. Slide thermostat switch to Off position.
2. Close propane tank valve if coach will be
stored for a period of time.
Further Information
Please see the furnace operating instructions
provided in your InfoCase for further
information, including operating precautions,
4-13
SECTION 4 –
APPLIANCES AND SYSTEMS
and periodic maintenance. See the Coach
Maintenance Schedule for recommended
intervals.
NOTE: If the furnace burner has any residuals
of metal protectant or lubricants used
during manufacture of the furnace, it
may smoke slightly when the furnace is
used for the first time and may set off
your smoke alarm.
We recommend that you provide
adequate ventilation when using the
furnace for the first time to avoid a
nuisance smoke alarm.
We do not recommend removing the
smoke alarm battery.
DUCTED ROOF AIR
CONDITIONING SYSTEM
The furnace thermostat also controls ducted
roof air conditioner operation when the
Thermostat switch is placed in “Cool” position.
All cooling functions controlling to setpoint
have a short cycle protection time delay of three
minutes. There will be no delay if the cycle OFF
time exceeds three minutes.
NOTE: The ducted roof air conditioning system
has ceiling registers that can be closed if
necessary to force more cool air toward
a specific area of the coach or to route
cool air away from a specific area. If too
many vents are closed, however, it can
cause the air conditioner unit to shut
down, particularly in high humidity
conditions.
Further Information
Refer to the manufacturer’s user guide
provided in your InfoCase for complete operating
instructions.
AIR CONDITIONER FILTER
The washable foam air conditioner filter is
located in the ceiling-mounted return A/C grille
in the lounge area of the coach.
4-14
It is recommended to check the filter monthly
for dirt build-up and cleaned or replaced, as
necessary.
SECTION 5 – PROPANE GAS
PROPANE GAS SUPPLY
The propane gas system supplies fuel for the
gas range/oven, water heater, furnace, and
refrigerator (while in gas mode). When used and
handled properly, this system is safe and
economical and provides modern living
conveniences wherever you travel.
See Section 2 - Safety and Precautions in this
manual for other safety and precautions you need
to be aware of related to propane.
Tank Fill
Valve
Overflow
Valve
Tank Gauge &
Sender
How Propane Gas Works
Propane Tank System
The storage reservoir for the propane gas
system is a horizontally mounted tank which is
permanently attached to the vehicle frame. The
tank is accessible only from the outside of the
vehicle.
Relief
Valve
Tank Supply
(Main) Valve
Pressure
Regulator
Propane Tank Features
-Typical View
WARNING
5 - DASH / AUTO
Propane is a type of LP (Liquefied Petroleum)
gas compressed into liquid form for easy
transportation and storage. Propane gas may also
be called tank gas, bottle gas, or simply LP.
Propane is used by appliances in vapor form
only, but is stored in the tank as a liquid under
very high pressure. As the liquid gas is released,
it reverts back to a vapor and expands to many
times its compressed volume.
Do not alter or remove propane tank
valves or gauge. Propane can escape,
which can cause an explosion resulting in
death or serious injury. Have the propane
system serviced by a qualified service
center.
Refilling Propane Tank
Since the propane tank is permanently
mounted to the frame, the motorhome must be
taken to a propane dealership for filling. Do not
attempt to remove the propane tank from the
vehicle. The tank is equipped with a fill adapter
with both internal and external threads, which
allows easy filling with any propane filling
equipment. The tank is full when liquid propane
gas appears at the overflow valve.
NOTE: The propane tank is equipped with an
automatic 80% stop-fill device.
5-1
SECTION 5 –
PROPANE GAS
Selecting Propane Fuel Types
WARNING
Do not fill propane container(s) to more
than 80 percent of capacity.
A properly filled container contains
approximately 80 percent of its volume as
liquid propane.
Overfilling propane container(s) can
result in uncontrolled propane flow, which
could lead to a fire or explosion and result
in death or serious injury.
DANGER
All pilot lights, appliances, and their
igniters (see operating instructions) shall
be turned off before refueling of motor fuel
tanks and/or propane containers. Can
cause ignition of flammable vapors, which
can lead to a fire or explosion and result in
death or serious injury.
We recommend using straight propane in your
propane tank. Propane gas is commonly available
at all propane gas outlets in the U.S. (According
to the National Propane Gas Association,
propane gas outlets in the United States do not
offer any other type of liquefied petroleum gas
than propane to the general public.) Check local
phone directory yellow pages for locations of
local propane gas refilling stations or bulk
dealerships.
NOTE: If you travel outside the U.S. with your
motorhome, you may find butane or
propane/butane mixtures available in
addition to propane. Because gasburning RV appliances are designed to
run on propane only, we recommend that
you request straight propane only.
Butane burns about 30 percent hotter
than propane and can overheat some
appliances, particularly refrigerators,
and cause permanent damage. Other
appliances designed to operate on
propane can become sooted and lose
efficiency by using butane fuel.
Air in the Propane Gas Tank
WARNING
This propane piping system is designed
for use with propane only.
Do not connect natural gas to this system.
Securely cap inlet when not connected for
use. After turning on propane, except
after normal cylinder replacement, test
propane piping and connections to
appliances for leakage with soapy water
or bubble solution.
Do not use products that contain
ammonia or chlorine to test for leaks. Can
lead to a fire or explosion, which could
result in death or serious injury.
5-2
If your gas appliances do not stay lit or require
frequent adjustment, even though you know the
propane tank contains sufficient fuel, the
problem may be air in the propane gas tank. Air
in the tank mixes with the propane gas vapors
causing them to burn poorly. This condition
could linger for weeks if the air is not purged
from the tank. Most propane gas dealers have
equipment for purging air from propane gas tanks
and will purge before refilling the tank.
PROPANE ACCESSORY
CONNECTION
–If Equipped
Your coach is featured with a Propane
Accessory Connection for your convenience, to
connect items such as a portable BBQ grill.
SECTION 5 –
PROPANE GAS
This connection is on the low pressure side of
the propane gas pressure regulator. Portable
appliances which have an additional or built-in
regulator may not operate correctly.
The Propane Accessory Connection is
provided with a shut-off valve that has on/off
indicator arrows. Rotate the shut-off valve
“clockwise” to turn gas supply OFF. Rotate the
shut-off valve “counter-clockwise” to turn gas
supply ON.
See Section 2 - Safety and Precautions in this
manual for other safety and precautions you need
to be aware of related to propane.
ON
OFF
LP Shut-off Valve
*Valve shown in the OFF (closed) position
Shut-off Valve
LP Accessory Connection
(Located behind access door on
passenger side of coach or at the rear of
the vehicle, depending on model)
-Typical View
C AU T I ON
Turn valve off when not in use.
Secure cap to outlet when not in use.
After turning on gas, test gas piping
connections to appliance for leakage with
soapy water or bubble solution.
Do not use products that contain
ammonia or chlorine.
SAFE USE OF THE PROPANE
GAS SYSTEM
The propane system is designed and built with
strict adherence to national, state, and
recreational vehicle industry requirements for
mobile propane gas equipment.
For your safety, there are many safety devices
and backup systems installed, such as fill
overflow valves, an interior propane gas detector/
alarm, and an interior carbon monoxide (CO)
detector/alarm.
Propane gas also contains an odor additive
that you can smell if propane is present in the air.
Here are a few precautions to observe that will
help you to use the propane gas system safely:
• Exercise caution at all times. Be familiar with
the distinctive odor of propane gas. If a leak is
suspected, turn off the supply valve
immediately. Have the propane gas system
checked by your dealer or other qualified
propane gas service center.
• Do not tamper with the propane gas piping
system, pressure regulator, or gas appliances.
Service and maintenance of propane gas
system components should be performed only
by your dealer or a qualified propane gas
service center.
• Never attempt to connect natural gas to the
propane gas system.
5-3
SECTION 5 –
PROPANE GAS
•
•
•
•
•
•
Have the entire propane gas system inspected
for possible leaks and missing or damaged
parts at each filling. Also inspect before and
after each trip, and any time trouble is
suspected.
Turn the propane supply valve off when not
using the propane gas system.
Never use a wrench to tighten the supply
valve. It is designed to close leak-tight by
hand. If a wrench is required to completely
close the valve, it is defective and must be
replaced.
Be sure appliance and outside vents are open
and free from obstruction when using the
propane gas system.
Never attach a lock or any device requiring a
key to the propane compartment door.
According to standards set for recreation
vehicles, the propane supply valve must be
readily accessible in an emergency.
Exercise caution when drilling holes or
attaching objects to the walls. Gas lines and
electrical wiring could be seriously damaged
and present an extreme safety hazard.
PROPANE GAS WARNINGS
AND PRECAUTIONS
It is illegal for vehicles equipped with propane
container to travel on certain roadways or
through certain tunnels in the U.S. To avoid
inconvenience, check state regulations
concerning flammable gas transportation.
DANGER
IF YOU SMELL PROPANE
1. Extinguish any open flames and all
smoking materials.
2. Shut off the propane supply at the
container valve(s) or propane supply
connection.
3. Do not touch electrical switches.
4. Open doors and other ventilating
openings.
5. Leave the area until odor clears.
6. Have the propane system checked
and leakage source corrected before
using again.
Ignition of flammable vapors could lead to
a fire or explosion and result in death or
serious injury.
•
•
•
All pilot lights must be extinguished and
appliances and their ignitors turned off while
refilling the fuel tank or propane container.
Never smoke while refilling vehicle fuel tank
or propane gas container.
Avoid inhaling exhaust gases produced by
burned gasoline, diesel fuel, or propane gas in
items such as the range, chassis engine,
generator engine, refrigerator, furnace, and
water heater. They contain carbon monoxide,
which is an odorless, colorless, and poisonous
gas.
Propane Gas Leaks
The following label is located in the vehicle
near the range area. If you smell gas within the
vehicle, quickly and carefully perform the
procedures listed.
5-4
WARNING
Do not place propane cylinders inside the
vehicle.
Propane cylinders are equipped with
safety devices that relieve excessive
pressure by discharging propane to the
atmosphere.
Propane gas is highly flammable.
Can lead to a fire or explosion and result
in death or serious injury.
SECTION 5 –
PROPANE GAS
•
•
•
Never use an open flame to test for propane
gas leaks. Replace all protective covers and
caps on propane system after filling. Make
sure valve is closed and door latched securely.
Portable fuel-burning equipment, including
wood and charcoal grills and stoves, shall not
be used inside the recreational vehicle. The
use of this equipment inside the recreational
vehicle may cause fires or asphyxiation.
Regulators are equipped with a protective
cover. Make sure that the regulator vent faces
downward and that the cover is kept in place
to minimize vent blockage, which could result
in excessive gas pressure causing fire or
explosion.
Gas
Pressure
Regulator
PROPANE GAS PRESSURE
REGULATOR
The pressure regulator is protected from the
elements by a plastic cover, which should be left
in place at all times.
Propane regulators must always be installed
with the regulator vents facing downward.
Regulators that are not in compartments have
been equipped with a protective cover. Make sure
that the regulator vent faces downward and that
the cover is kept in place to minimize vent
blockage that could result in excessive propane
pressure causing fire or explosion.
Only your dealer or a qualified propane gas
service should remove the regulator cover for
adjustments.
WARNING
Visually inspect the pressure regulator
vent periodically for blockage by
accumulated debris or insect nests, etc.
Vent obstruction could result in excessive
pressure causing fire or explosion, which
could result in death or serious injury. If an
obstruction exists, have the regulator
serviced by a qualified service center.
Look up inside hole on underside of regulator
housing to see vent screen.
Be sure vent
hole is not
blocked.
Regulator Freeze-up
Regulator freeze-ups are caused by the
presence of moisture in fuel. This moisture will
pass through the cylinder valve and into the
regulator where it can freeze. Fuel producers,
tank and bottle manufacturers, and propane gas
dealers take every precaution to reduce moisture,
5-5
SECTION 5 –
PROPANE GAS
but sometimes only a fraction of an ounce
entering the tank can cause problems. To help
avoid the possibility of freeze-up, always keep
tank control valve closed when not in use, even
when tank is empty, to prevent moisture from
collecting on the inside.
If regulator freeze-up should occur, you may
attempt to thaw the regulator using a light bulb.
DO NOT USE AN OPEN FLAME OR HEAT
LAMP.
If moisture begins to cause problems, have
your propane gas dealer inject a small amount of
dry methyl alcohol in your tank (approximately
one ounce to 20 pounds or one pint to 100
gallons) to help guard against regulator freezeups.
PROPANE VAPORIZATION IN
COLD WEATHER
Propane gas vaporization increases and
decreases in direct relation to ambient
temperature. In other words, the lower the
temperature, the slower the liquid propane will
vaporize into a usable gas for appliances.
This means that in extremely cold weather
when a large volume of gas is being used by the
furnace for heating, it is possible to experience a
loss of gas pressure.
At first, this problem may appear to be caused
by an empty tank or a regulator freeze-up, but is
actually caused by failure of the liquid gas to
vaporize as fast as it is needed by the furnace.
The demand for propane to produce heat
increases to the point where the gas cannot
vaporize fast enough to keep the furnace going.
The only solution to this problem is to reduce gas
usage where possible.
Adjusting the temperature on the gas/electric
refrigerator may be a first step. Using less hot
water will also help, as well as refraining from
using the gas cooktop. A final step is to lower the
thermostat setting to reduce gas usage by the
furnace.
5-6
SECTION 6 – ELECTRICAL
ELECTRICAL CAUTIONS
•
•
•
•
•
•
Careless handling of electrical components
can be fatal. Never touch or use electrical
components or appliances while feet are bare,
while hands are wet, or while standing in
water or on wet ground.
Improper grounding of the vehicle can cause
personal injury. Do not plug the utility power
cord into an outlet which is not grounded and
do not adapt the plug to connect to a receptacle
for which it is not designed.
Do not attach an extension cord to the utility
power cord.
Be sure that all electrical appliances to be used
contain 3-prong plugs for proper grounding.
Avoid overloading electrical circuits. Replace
fuses or circuit breakers with those of the
same size and amperage rating only. Never
use a higher rated fuse or breaker.
Use caution when handling or working near
electrical storage batteries. Always remove
jewelry and wear protective clothing and eye
covering. Avoid creating sparks.
ELECTRICAL SYSTEM –
HOUSE 120-VOLT AC
The 120-volt system operates from the
shoreline cord connected to an outside 120-volt
utility service, such as those at campgrounds or
from the 120-volt generator. When the shoreline
cord is connected to an outside power source, or
when the auxiliary electric generator is running,
the power converter automatically changes a
portion of the 120-volt current to 12-volt DC
current. All equipment in the motorhome that is
normally powered by the house batteries is then
powered through the converter.
In addition, the following equipment is
entirely dependent on 120-volt current: air
conditioner, refrigerator, microwave oven, and
any 120-volt electrical equipment used at
convenience outlets.
POWER CORD – EXTERNAL
(Shoreline)
WARNING
Do not use an extension cord. Improper
sized cords, damaged cords, and poor
connections can lead to fire, which can
result in death or serious injury.
5 - DASH / AUTO
Your coach is equipped with an electrical
system consisting of two separate voltages:
• 12-volt DC system (battery current); and
• 120-volt AC system (household current)
The 12-volt system consists of two internal
power sources, while the 120-volt system is
operated from an outside power source or the
optional 120-volt generator.
WARNING
Do not connect the external power cord to
any receptacle until you have verified
proper polarity and grounding. Be sure all
prongs of the supply cord are properly
plugged into the receptacle. Failure to
observe can result in death or serious
injury.
The external power cord (commonly referred
to as a “shoreline”) is located in a driver side
compartment.
To connect to an external power source,
remove the power cord from the utility
compartment and plug it into a suitable power
outlet box.
6-1
SECTION 6 –
ELECTRICAL
30 Amp Receptacle
WARNING
This connection is for 110/125 Volt AC,
60 Hz 30 Ampere supply.
Do not exceed circuit rating. Exceeding
the circuit rating may cause a fire and
result in death or serious injury.
• Swivel the small cover section upward
to access the cord passage.
The power cord is designed to ground the
electrical system through the receptacle. It is also
designed to carry the amperage output of most
campground outlets. If the electrical receptacle to
be used is designed to mate with the prongs of the
power cord plug, the electrical connection can be
expected to carry rated load.
Power Cord Door
(Models with power cord compartment on
sidewall)
–If Equipped
A flip-up passage in the power cord door lets
you route the power cord out of the compartment
and close the door while the power cord is
connected.
• Route power cord through passage
and close door while shoreline is
connected to outlet.
Power Cord Hatch
–If Equipped
A threaded port utility hatch lets you route the
power cord out the bottom of the compartment so
you can close the compartment door while the
power cord is connected.
1. Rotate the threaded port utility hatch
counterclockwise to remove.
6-2
SECTION 6 –
ELECTRICAL
WARNING
Service inlet access must be closed when
utility connections are not in use.
Park Fuses or Breakers
2. Route the cord through the hole.
Most campgrounds are equipped with a fuse
or circuit breaker at the receptacle (which we
recommend shutting off before engaging or
disengaging the power cord.) This protects the
park’s wiring, as well as the power cord on your
vehicle from electrical damage. If electrical
power fails, contact the park attendants and have
them check the fuse or breaker for your supply
receptacle.
INVERTER UNIT – 1000W
–If Equipped
The inverter changes 12-volt DC battery
power into 120-volt AC power for use by 120volt AC equipment inside the coach. The inverter
unit is located inside an interior cabinet.
3. Rotate the threaded port utility hatch
clockwise to close.
After disconnecting the power cord, neatly
replace it in the cord compartment.
NOTE: Batteries will deplete with use of the
inverter.
Monitor battery levels regularly when
not connected to shoreline or generator
power.
The inverter can also be used while
driving the motorhome because the
engine alternator will charge the
batteries while driving.
The inverter has built in GFCI protection. The
GFCI will protect against electrical shock by
interrupting the flow of electricity. If there is no
power from the inverter the GFCI may have
tripped. Reset the GFCI by pressing the RESET
button. If the GFCI continues to trip, have the
electrical system checked and repaired, if
necessary, before using the inverter again.
6-3
SECTION 6 –
ELECTRICAL
NOTE: Do not leave the shoreline plugged in
during storage. Follow regular battery
inspection and maintenance.
Inverter Control Panel
–If Equipped
The inverter has a wall-mounted monitor/
control panel. It will also indicate warnings for
overload conditions or other operating failure
conditions.
Inverter Unit
-Typical View
Inverter Locations
• Model 22M - Located on floor beneath range/
oven. Open cabinet door below galley sink to
access.
• Model 22R - Located under rear dinette seat.
Remove dinette cushion to reveal access hole.
• Model 25B - Located beneath sofa near range/
oven. Remove front panel beneath sofa to
access.
• Model 26A - Located beneath refrigerator.
Remove drawer beneath refrigerator to
access.
• Model 31D - Located beneath refrigerator.
Remove drawer beneath refrigerator to
access.
• Model 31G - Located beneath sofa. Remove
front panel beneath sofa to access.
• Model 31K - Located on floor behind load
center. Remove lower galley cabinet drawer
to access.
NOTICE
Do not store items around the inverter
unit. The inverter generates heat while
operating and needs unrestricted airflow
for proper cooling. Damage to the inverter
can result.
6-4
Inverter Control Panel
(Located near monitor panel)
-Typical View
When the inverter is not being used, it should
be shut off at the control panel. The inverter
could drain the house batteries if the shoreline is
not connected to external power and the House/
Coach Battery Disconnect switch is on.
Further Information
See the inverter control panel instructions in
your InfoCase for complete instructions and
charging setup directions.
POWER CENTER
(Converter)
The power converter is generally located in a
lower cabinet face in the galley or living area,
depending on the floorplan of your model.
The converter power panel contains the house
electrical system 120-volt circuit breakers and
12-volt fuses.
The power converter changes 120-volt AC
current from the auxiliary generator or the
shoreline into 12-volt DC current for use by 12volt equipment in the motorhome.
SECTION 6 –
ELECTRICAL
120-Volt
Circuit Breakers
12-Volt
House Fuses
condition of the battery. If it is below “full
charge”, the charging section will start charging
the batteries.
If the house batteries have been extremely
discharged, they will accept charge at a relatively
high amperage rate. If they are only slightly
discharged, they will charge at a lower amperage
rate. The rate of charge will decrease as the
batteries reach “full charge”, then will continue
“trickle” charging at a very low amperage rate. If
your battery does not charge as described above,
it is possible the battery is defective.
Thermal Overload
Power Center (Converter)
-Typical View
Certain circuits, however, remain unchanged
for use by items which require 120-volt current,
such as the air conditioner(s), the refrigerator in
AC mode, the microwave oven, etc.
NOTE: The converter will not change 12-volt
DC current to 120-volt AC.
Current drawn from the house batteries passes
through the power converter unchanged,
although it is routed through a series of protective
fuses located on the power panel.
NOTICE
Do not block the converter cover vents in
any way. The converter generates heat
while operating and needs unrestricted
airflow for proper cooling. Damage to the
converter can result.
Further Information
See the manufacturer’s operation, care, and
maintenance information provided in your
InfoCase.
Charging Section
The converter charges house batteries while
120-volt external power is connected. The
converter will automatically “sense” the
A thermal overload will “break” the 120-volt
AC power to the converter section of the power
center if the power converter becomes
overheated. This can result from operating above
its maximum limit for an extended period of time
or by obstruction of ventilation to unit.
NOTE: The power converter section will
automatically route 12-volt lights and
motors to house battery power in this
event.
The thermal overload will reset itself after a
period of time, and the lights and motors will
again resume operation from the power converter
section. If the breaker trips again shortly after
reset, take immediate steps to correct the cause of
overheating. A portion of the house 12-volt load
(lights or motors or both) should be turned off to
reduce total load. Also, inspect the power
converter to ensure ventilation is not obstructed.
CIRCUIT BREAKERS – HOUSE
120-VOLT AC
The breaker panel protects all 120-volt
components in the motorhome from either an
overload on the circuit or a short in the wiring or
component itself. When an overload or short
develops, the breaker will open preventing
damage to the system.
Shut off the equipment (example: roof air
conditioner) and allow a brief cooling period.
Then reset the breaker by moving the switch to
“Off” and back to “On”. If the breaker is
6-5
SECTION 6 –
ELECTRICAL
continually tripped and no overload is evident,
have the system checked for a short in the wiring
or the appliances.
If the GFCI keeps tripping, have the electrical
system checked and repaired, if necessary, before
using again.
•Push to Reset
circuit after
monthly testing
or ground fault
tripping.
•Push to Test at
least monthly.
Should break
circuit. Press
Reset button to
reconnect.
120-Volt Circuit Breakers
-Typical View
NOTE: Typical view of breaker panel. Breaker
arrangement may vary according to
appliance and equipment options. Fuses
and breakers are labeled on panel.
GFCI Outlet
(Ground Fault Protector)
ELECTRICAL OUTLETS –
HOUSE 120-VOLT AC
A number of standard household electrical
outlets are provided throughout the coach for
connecting small appliances such as televisions,
radios, toasters, etc.
An exterior outlet is also located on the
outside of the coach near the entrance door or in
a storage compartment on the passenger side of
the coach.
WARNING
The GFCI will not completely eliminate
the risk of electrical shock. Infants and
small children may still be affected.
ELECTRICAL GENERATOR –
120-VOLT
–If Equipped
GROUND FAULT CIRCUIT
INTERRUPTER
Bath, galley, and exterior outlets are
connected to a GFCI (Ground Fault Circuit
Interrupter), which is an extremely sensitive
circuit breaker that will help to protect against
severe electrical shock if a ground fault develops.
If such a condition occurs, the GFCI will break
the circuit by turning off the power to the
protected outlets. Should this occur, unplug all
the appliances on that circuit and press the reset
button on the GFCI equipped outlet.
6-6
WARNING
Careless handling of the generator and
electrical components can be fatal.
Never touch electrical leads or appliances
when your hands are wet, or when
standing in water or on wet ground.
Do not attempt to repair the generator
yourself. Service should be performed by
a qualified service center.
SECTION 6 –
ELECTRICAL
To use the 120-volt generator, plug the power
cord into the generator receptacle within the
utility compartment before starting the generator.
Automatic Power Transfer Box
(Located inside utility compartment)
-Typical installation shown
Generator
Receptacle
Power Cord
WARNING
The following label is located near the 120volt house circuit breaker panel and at the
Generator to warn you to disconnect specific
electrical connections before servicing the
Generator and storing the coach.
Do not plug the power cord into the
generator receptacle while the generator
is running. Electrical shock can cause
personal injury.
Automatic Power Transfer Switch
–If Equipped
Whenever the Generator is started, an
automatic power transfer system automatically
switches the household electrical system to the
Generator approximately 30 seconds after the
Generator is started. The 30 second delay allows
the Generator to start easily without the burden of
electrical loads.
Generator Operation
See the manufacturer’s operation, care and
maintenance in your InfoCase.
Generator Hourmeter
This meter is located on the monitor panel. It
registers the total number of hours that the
generator has been operated.
6-7
SECTION 6 –
ELECTRICAL
Refer to the hourmeter to determine when
periodic maintenance is due and to record
services which have been performed.
Operation Warnings and Cautions
WARNING
The exhaust of all internal combustion
engines contains carbon monoxide (CO).
This poisonous gas is colorless, odorless,
tasteless, and lighter than air. The
exhaust systems of both your motorhome
engine and your generator engine have
been installed with your safety in mind.
However, certain precautions must be
taken when using them to protect yourself
from conditions beyond the control of the
manufacturer.
1. Do not simultaneously operate the generator
and a power vent, which could draw exhaust
gases into the vehicle.
2. Do not open windows or vents on the end or
side of the vehicle where exhaust pipe of the
generator is located.
3. Park the vehicle so that the wind will carry the
exhaust away from the vehicle. Also, note the
position of other vehicles to be sure their
exhaust will not enter your vehicle.
4. Do not operate the generator engine while
parked if vegetation, snow, buildings,
vehicles, or any other object can deflect the
exhaust under or into the vehicle.
NOTE: Check auxiliary generator oil level
frequently during periods of use.
Refer to the generator manufacturer’s
maintenance information in your InfoCase for
specific recommendations.
ELECTRICAL SYSTEM –
HOUSE 12-VOLT DC
The DC voltage system consists of the chassis
battery, the 12-volt house batteries, and the 12volt power converter.
6-8
Converter
See “Converter” previously in this section.
Chassis Battery
The chassis battery is used to operate the
engine starter and automotive accessories and
controls found on the instrument panel. The
electric step is also connected to the chassis
battery.
Refer to your chassis manual provided in your
InfoCase for further information on chassis
batteries and chassis electrical system.
House Batteries
House batteries are “deep-cycle” type
batteries specially designed for recreational
vehicle use. They will provide longer lasting
power than standard automotive starting batteries
and will withstand the frequent drain-andrecharge cycles that occur under the demanding
conditions of a camping outing.
The house batteries supply power to 12-volt
equipment located in the living area of the
motorhome. This includes the following 12-volt
powered components (if equipped): interior 12volt lighting, range exhaust fan, propane furnace
fan, fresh water pump, systems monitor panel,
refrigerator, roof vent fans, and 120-volt
electrical generator starter.
The house batteries can also provide
emergency power to start the engine if the chassis
battery is discharged. (See “Battery Boost
Switch” in Section 3 - Driving Your Motorhome).
House batteries are automatically charged by
the chassis alternator while the engine is running.
HOUSE/COACH BATTERY
DISCONNECT SWITCH
(COACH BATT)
The House/Coach Battery Disconnect switch
lets you disconnect the house batteries from the
12-volt system of your coach during storage
periods to avoid battery drain by electrical items
that are hooked directly to the house batteries,
such as clock displays and radio memories, etc.
SECTION 6 –
ELECTRICAL
Always leave this switch ON while using the
coach.
NOTE: Some electronic displays and memory
functions may need to be reset after
power has been reconnected.
See also “Battery Care” elsewhere in this
section.
House
Batteries
-Typical View
C AU T I ON
Step cover must be closed and latched.
Failure can cause injury.
House/Coach Battery Disconnect Switch
(Located near entrance door)
-Typical View
BATTERY ACCESS
The house/coach batteries are located beneath
the interior entrance steps. The chassis batteries
are located under the front hood.
• Unfasten the step retainer, then lift the step
upward and remove to service batteries.
•Squeeze tab
upward to release
latch
BATTERY CARE
Lead-acid type batteries are electro-chemical
devices for storing and releasing electrical
charge. As such, they are simply an electrical
reservoir, not an electrical source. As soon as
energy is removed from the battery, it should be
replaced by the engine alternator or the coach
converter system.
If a battery sits unused for 30 days or more,
especially during warm weather, it can develop a
deposit of sulfate crystals on the metal plates
inside the battery. This condition is called
“sulfating” and prevents the battery from either
releasing or accepting a charge. If this condition
occurs, the battery must be replaced.
If a battery does not contain at least 80%
charge during freezing temperatures, the
electrolyte can freeze and crack the battery case.
-Typical View
6-9
SECTION 6 –
ELECTRICAL
The two best defenses against sulfating
and insufficient charge are to:
1. Turn off the House/Coach Battery Disconnect
switch to avoid parasitic discharge (the trickle
discharge caused by directly connected
components like propane gas detectors or
digital clock displays, etc.)
2. Check the battery and recharge as necessary at
least once a month during long storage
periods. Turn the House/Coach Battery
Disconnect switch off to avoid electrical
arcing when attaching or detaching charger
clamps.
NOTICE
Disconnect batteries before connecting
external charging equipment to avoid
damage to sensitive electronic
components.
NOTE: Do not leave the shoreline plugged in
during storage. Follow regular battery
inspection and maintenance.
Further precautions are:
• Check the state of charge periodically to avoid
discharge or sulfating.
To ensure that the battery will always accept
and hold a charge, follow these simple
maintenance practices:
• Make sure the batteries always remain
securely clamped in the battery tray.
• Make sure battery cable clamps are tight on
the terminal posts and are free of corrosion.
• Neutralize corrosion buildup or acid film on
top of battery by washing with a baking soda/
water solution. Rinse with clear water.
NOTE: Make sure vent caps are on securely to
prevent baking soda solution from
entering the battery and contaminating
the electrolyte fluid.
WARNING
WARNING
Before removing any battery cables or
battery, make sure all 12-volt equipment
in the motorhome is off and the power
cord has been disconnected. Be sure to
replace the battery terminal boot, if
supplied, back onto the positive terminal
after servicing. Care must be taken to
avoid pinching the cable between any
metal parts. Should the cable be
damaged, a short circuit could result in
personal injury or damage to equipment.
Replace any damaged cables at once.
Always remove jewelry and wear
protective clothing and eye covering
when checking or handling batteries.
This vehicle, like other vehicles, may
contain small amounts of one or more
substances which are listed by the state
of California for causing cancer or
reproductive toxicity.
WARNING
California Proposition 65 Warning:
Battery posts, terminals, and related
accessories contain lead and lead
compounds, chemicals known to the
state of California to cause cancer and
reproductive harm. Wash hands after
handling.
6-10
•
Clean and tighten battery terminals and have
the specific gravity checked at least once a
year.
SECTION 6 –
ELECTRICAL
•
•
Check the battery fluid level every month, or
more often in hot weather. Fill to
approximately 3/8 inch above the plates. DO
NOT OVERFILL. If fluid is added during
freezing weather, the motorhome should be
driven several miles to mix water and
electrolyte to prevent freezing.
Fluid level check may be omitted if equipped
with maintenance-free batteries.
affected lights or appliances and reset the breaker
or replace the fuse with a new one of equal
amperage rating.
House 12-Volt Fuses
A label on the House 12-Volt Fuse panel
states the amperage rating and circuit protected
for each fuse.
WARNING
To prevent wiring damage, it is essential
when replacing the cables on the battery,
or when using a “booster” battery, that the
positive post and the positive cable be
attached and the negative post and
negative cable be attached. The posts are
marked (+) plus and (-) minus.
If a “boost charger” is used while battery
is in the motorhome, disconnect both
battery cables before connecting the
charger to avoid damage to engine
electronic components.
Never attempt to charge or boost a frozen
battery. An explosion can occur resulting
in personal injury.
House 12-Volt Fuses
(Located on the right-hand side
of the power converter)
-Typical View
The fuse panel accepts only blade type plug-in
fuses. Always replace fuses with those of the
same amperage rating.
30
30
Functional
Non-Functional
Chassis Battery
If your coach is going to be unoccupied for
two weeks or more, Winnebago Industries®
recommends disconnecting the chassis battery in
your coach to avoid battery discharge.
Disconnect the ground cable on the chassis
battery (located under front hood) to disconnect
battery.
Battery Charge Meter
CIRCUIT BREAKERS AND
FUSES – HOUSE 12-VOLT DC
Battery Boost Switch
All 12-volt circuits and equipment in the
coach area of the motorhome are protected by
either a fuse panel or breaker panel. When a
circuit is overloaded or a short develops in any
part of the system, a fuse or breaker will shut
down that circuit. If this happens, turn off all
See related item under “Systems Monitor
Panel” in Section 4 - Appliances.
See Section 3 - Driving Your Motorhome for
information on the Battery Boost switch.
6-11
SECTION 7 – PLUMBING
The tank is filled through the Tank Fill
Connection located on the side of the vehicle.
The Fresh Water System provides water to the
galley sink, shower, bathroom lavatory, toilet,
and water heater. Water may be supplied by
either of two sources:
• A fresh water tank and water pump located
within the motorhome, or
• Any external fresh water source to which the
motorhome may be connected, known as “city
water”.
Water Pressure Regulators
Because city water pressure varies from
location to location, we recommend obtaining an
in-line water pressure regulator to prevent
damage to any components, connections, and
seals in your fresh water system.
These devices simply connect in-line between
the supply hose and the city water input on the
coach. We recommend regulators that control
water pressure to 50 psi. max.
Water pressure regulators are commonly
available at most RV dealerships and many large
retail discount or home supply centers.
Filling the Fresh Water Tank
WARNING
Potable water only.
Sanitize, flush, and drain water tank
before using.
See owner’s manual for instructions,
care, and maintenance information.
Failure to maintain tank can result in
death or serious injury.
Always fill the fresh water tank at an approved
potable water filling facility or a known purified
drinking water source.
City Water Connection
Tank Fill Connection
-Typical View
1. Attach hose to the Tank Fill Connection.
2. Turn water supply ON.
3. Use the level display on the monitor panel to
oversee filling of the tank, or when the tank is
full, water will flow from tank vent tube
beneath coach.
NOTICE
Do not leave fresh water connection
unattended when filling tank. Failure to
comply may result in tank expansion and
property damage.
4. Turn OFF water supply and disconnect from
the Fresh Water Inlet.
Using City Water
When connected to an outside source of water,
the water bypasses the water pump and storage
tank and supplies pressure directly to individual
faucets and toilet. A check valve built into the
pump prevents water from entering the pump and
filling the storage tank.
1. Connect hose to City Water Connection.
7-1
5 - DASH / AUTO
FRESH WATER SYSTEM
SECTION 7 –
PLUMBING
2. Turn the Water Pump switch(es) OFF.
Disconnecting from City Water
1. Turn the city water supply OFF.
2. Disconnect hose from the coach and replace
the cap on the City Water Connection.
3. Turn the Water Pump Switch(es) ON.
WATER PUMP
When your coach is not connected to a city
water supply, water is supplied from the fresh
water tank by a water system demand pump. A
demand pump is designed to run only when you
are using water. When you open a faucet, the
waterline pressure drops and the pump begins to
run, and it will continue to run as long as the
faucet is open. When you close the faucet, the
line pressure backs up to the pump, and it shuts
itself off.
The pump is self-priming and will run briefly
to build up line pressure when the Water Pump
switch is first turned on. See “Initial Waterline
Priming” for instructions on using the water
system for the first time.
Water Pump Strainer
The pump is equipped with a cleanable
strainer to capture any possible tank-borne
particles that could damage pump components.
NOTE: We recommend that you check and clean
the strainer after each tankful of water
during the first few uses of the Water
Pump system. Thereafter, remember to
check it at least yearly, and be sure to
empty water from it if using the blowout
winterization procedure.
Unscrew bowl
and remove to
clean strainer
Water Pump Strainer
-Typical View
To Clean Pump Strainer
• Ensure all Water Pump switches are OFF.
• Twist the inlet cap (bowl) “counterclockwise” to unscrew from the strainer
assembly.
• Remove the bowl and pull the strainer screen
out of the bowl to tap out any particles and
rinse clean.
• Insert the strainer screen back into the bowl,
then screw the bowl back onto the strainer
assembly.
Water Pump Switch
The Water Pump switch is located near the
monitor panel (some models may have an
additional switch in the water service center, near
the exterior shower, or within the bathroom area
for your convenience).
While the switch is “ON”, the pump will
automatically supply water as it is needed.
We recommend that you turn the Water Pump
switch off whenever you will be away from the
vehicle or not using the water system. In time, a
slow leak in a faucet could drain the water tank,
fill the holding tank, and discharge the house
batteries.
Initial Waterline Priming
1. Ensure that all water drain valves are closed,
including water heater valve.
2. Turn Water Pump switch to “OFF” position.
7-2
SECTION 7 –
PLUMBING
3.
4.
5.
6.
Fill water tank.
Open all faucets, hot and cold.
Turn ON the Water Pump switch.
Close each faucet as it begins to deliver a
steady stream of water (close cold water first).
Leave hot water faucets on until they also
deliver a steady stream of water. This will
ensure that the water heater is filled with
water.
7. Check to ensure the Water Pump stops soon
after all faucets have been closed.
8. The Water Pump is now ready for automatic
operation. The pump will start when a faucet
is opened and stop when the faucet is closed.
Water Pump
(Located beneath bed - lift mattress to
expose access hole)
*Models 22R, 25B, 31G, and 31K
Further Information
Refer to the Water Pump manufacturer’s
operation, care, and maintenance information
provided in your InfoCase.
Water Pump
(Located behind access door
in bottom of pantry)
*Models 22M
Water Pump
(Located beneath bed - extend rear bed
slideout, remove mattress from bed, and lift
hinged bed board to access)
*Model 26A
Water Pump
(Located beneath bed - remove panel at foot
of bed to access)
*Model 31D
7-3
SECTION 7 –
PLUMBING
ICE MAKER WATER FILTER
–If Equipped
If the refrigerator in your coach is equipped
with an ice maker, an ice maker filter is provided,
which removes chlorine and odors for clean,
taste-free ice cubes.
NOTE: When removing the coach from storage,
always disinfect and flush the water
system thoroughly before installing a
new filter.
DISINFECTING YOUR FRESH
WATER SYSTEM
(As required by NFPA®1192 Standard on
Recreational Vehicles)
To ensure complete disinfection of the potable
water system, it is recommended that the
following procedure be followed on a new
system, one that has not been used for a period of
time, or one that could have become
contaminated.
This procedure is also recommended before
long periods of storage, such as over winter.
Disinfecting with City Water Fill
Ice Maker Filter Assembly
(Located below galley sink)
-Typical Installation
Replacing the Ice Maker Filter
Cartridge
The filter cartridge must be replaced at least
every 12 months.
• Place a container beneath the filter to catch
any water remaining in the waterlines during
filter removal.
• Twist the filter cartridge counter-clockwise
(to the left) about one-quarter turn, then pull it
down and out of the filter socket. (A springloaded valve inside the filter socket will block
water from flowing out of the socket when the
filter cartridge is removed).
• Insert a new filter cartridge up into the filter
socket as far as possible and twist it clockwise
(to the right) one-quarter turn until it stops.
• Discard the first two batches of ice cubes to
avoid consuming carbon dust or particles that
may have been present in the new filter
cartridge.
• See “Winterization Procedure” at the end of
this section for further information.
7-4
When disinfecting through the city water fill,
an external cartridge-type water filter assembly
must be connected in-line between the city water
hose and the city water fill to add disinfecting
solution to the tank. These filters are commonly
available at most RV supply stores.
NOTE: If you do not have an in-line cartridge
filter, see City Water Hose/Tank
Disinfection following this procedure for
an alternate method of adding bleach
solution to your tank.
1. Remove the filter cartridge and pour 1/4 cup
of household chlorine bleach (sodium
hypochlorite solution) for each 15 gallons of
tank capacity into the empty filter canister,
then screw the canister back onto the filter
base.
WARNING
Chlorine is poisonous. Do not misuse.
Recap bottle and clean all utensils after
use.
SECTION 7 –
PLUMBING
This solution will result in a residual chlorine
concentration of approximately 50 ppm in the
water system. (If a 100 ppm concentration is
desired, use 1/2 cup of household bleach for each
15 gallons of tank capacity). The bleach will be
drawn into the tank when the city water is turned
on.
2. Fill the tank completely, then open each faucet
in the coach and run the water until a distinct
odor of chlorine can be detected in the water
discharged. Do not forget the hot water
faucets.
3. Let the system stand at least 4 hours when
disinfecting with 50 ppm residual chlorine. (If
a shorter time period is desired, then a 100
ppm chlorine concentration should be
allowed to stand in the system for at least 1
hour).
4. Drain the fresh water tank.
5. Install the filter cartridge into the filter
canister, then refill the tank with fresh water.
6. Open each faucet again and run fresh water to
flush chlorinated water from the lines. Run the
water until there is no odor of chlorine
detected in the water discharged. Do not
forget the hot water faucets.
(You may need to leave a hot water faucet
open for some time to flush the water heater
with clean water. You may also want to turn
the water heater off until this is done to avoid
wasting energy trying to heat “unused”
water).
7. Water system is now disinfected.
City Water Hose/Tank Disinfection
As an alternative way to disinfect your tank,
connect a city water hose to your coach and pour
the bleach into the other end of the hose using a
funnel. Hold the hose upright to avoid draining
the bleach.
Connect the hose to a city water hydrant to force
the bleach into the tank and fill the tank with
water.
This method has the additional benefit of
disinfecting the city water hose at the same time.
Continuous Tank Disinfection
(Superchlorination)
Some RVers like to ensure continuous
sanitation of their fresh water tank by
“superchlorination”– maintaining an effective
low level of chlorine in the tank at all times.
• Add 1 teaspoon of household chlorine bleach
(sodium hypochlorite) to your tank for each
10 gallons of tank capacity. When you fill the
tank, this will result in a 6.7 ppm level of
chlorine, which should kill harmful bacteria
and slime-forming organisms.
• Chlorine may be removed from drinking
water by the cold water filter at the galley
faucet (if equipped) or by installing an
activated carbon water purifier at the galley
sink cold water line or a separate drinking
water faucet with filter.
• Superchlorination does not affect city water
usage, only the fresh water tank.
SHOWER HOSE VACUUM
BREAKER
After using the shower, you may notice water
dripping from the shower faucet assembly. The
dripping results when vacuum in the shower hose
(after closing the shower faucet) slowly releases
and allows water remaining in the hose to drain
down. This is a normal function of the shower
valve assembly and is not a leak or defect.
If items are placed into the shower tub before
shower valve vacuum release is complete, they
may become wet.
EXTERIOR SHOWER/WASH
STATION
–If Equipped
The exterior wash station feature allows you
to do things such as rinse off sand or salt after a
swim, rinse off muddy boots, or bathe your pet
outside the coach. Some models may have a
water pump switch located in the service center
for convenience.
7-5
SECTION 7 –
PLUMBING
NOTE: The exterior wash station detachable
hose is stored in the rear of the vehicle or
inside an exterior compartment,
depending on model.
•
Don’t put automotive antifreeze or caustic
chemicals, such as laundry bleach or heavy
detergents into the toilet or holding tank.
These products may damage plastic or rubber
parts in the system.
See winterizing instructions at the end of this
section to prepare the toilet for storage in freezing
conditions.
Further Information
See the toilet manufacturer’s operation
information in your InfoCase for complete
operating, care, and maintenance information.
DRAINAGE SYSTEM (P-TRAPS)
Exterior Shower/Wash Station
(Typical)
TOILET
–If Equipped
The toilet in your motorhome is very similar
to the household type, except that it is designed to
use only a small amount of water per flush. It
uses a high velocity jet of water, producing a
swirl effect, to efficiently cleanse the bowl.
Important “Don’ts”
•
•
7-6
Don't use facial tissue or regular toilet tissue in
the RV toilet. These will not disintegrate
sufficiently and will often cling to the sides of
the holding tank. Toilet tissue made
specifically for use in RV toilets and holding
tanks is available at most RV supply centers.
Don’t dispose of sanitary napkins or other
non-dissolving items in the toilet.
Ensure there is an adequate amount of water in
the drainage system p-traps to avoid sewer odor
from entering your coach.
If you should experience a sewer odor, pour
approximately 1 cup of water down each sink and
shower drain in the coach.
WASTE WATER SYSTEM
(Holding Tanks)
The drainage system is self-contained and
uses two separate holding tanks to contain the
waste water until it can be dumped at an
appropriate waste water disposal site. This means
you can use the toilet, sinks, and shower even in
areas where utility hookups are not available.
The black water holding tank contains the
sewage from the toilet and may include bathroom
lavatory on some models. The gray water holding
tank contains the waste water from the galley
sink and shower, and may include bathroom
lavatory.
See “Specifications” in Section 1 Introduction for tank capacities for your model.
Dumping Holding Tanks
1. Remove sewage drain hose from rear bumper
storage.
2. Remove dust cap from sewage drain outlet
and connect sewer hose. Be sure it is firmly
attached.
SECTION 7 –
PLUMBING
NOTE: The sewage drain outlet on your coach
may swivel downward (depending on
model) when necessary to avoid bends in
the sewage drain hose, which could trap
solids while dumping or to provide more
direct drainage while using on-site
sewer hook-ups.
3. Place the outlet end of sewage drain hose into
disposal opening.
1st - Pull Black Waste Tank Drain
valve to drain black water (sewage)
tank - then close.
5. Open the Gray Waste Tank Drain valve. Be
sure there are no sags in the hose to ensure
complete drainage. Close Gray Waste Tank
Drain valve as soon as tank is empty.
6. Add an odor control chemical to the sewage
holding tank through the toilet. These
chemicals are available at most RV stores.
7. Rinse sewage drain hose thoroughly with
water and stow.
NOTE: We recommend that you dump all
holding tanks before traveling to avoid
carrying unnecessary weight.
Flushing Your Black Waste Holding
Tank
–If Equipped
The black waste holding tank is equipped with
an internal spray head that allows you to rinse the
inside of the tank with a shower of clean water
after dumping.
2nd - Pull Gray Waste
Tank Drain valve to
drain gray water (sink/
shower) tank - then
close.
Sewage
Drain Outlet/
Dust Cap
NOTE: Black and Gray tank valve positions may
be reversed depending on floorplan and
tank location.
4. Open the Black Waste Tank Drain valve with
a quick pull and make sure there are no sags in
the hose. Move the hose gently about to
dislodge any waste and ensure complete
drainage. Close Black Waste Tank Drain
valve as soon as tank is empty.
NOTE: DO NOT OPEN BOTH VALVES AT
ONCE. Do not open the Gray Waste Tank
Drain valve until the black tank is
drained and Black Waste Tank Drain
valve is closed to avoid sewage back-up
into gray tank. Gray water also rinses
any black water solids from the sewage
drain hose.
C AU T I ON
Do not use the tank flush valve unless the
fullway termination valve is in the open
position. May result in an unsanitary
condition leading to illness or personal
injury.
1. Dump your black waste holding tank in the
usual manner at an approved sewage disposal
station.
2. Leave Black Waste Tank Drain valve open
while flushing tank.
3. Attach a garden hose from a city water
hydrant to the Black Waste Tank Flush Inlet
fitting on the left sidewall. (This inlet is
clearly marked separate from the City Water
inlet).
7-7
SECTION 7 –
PLUMBING
NOTE: Always keep sewage drain outlet capped
while sewage connection is not in use.
Holding Tank Level Indicators
See “Systems Monitor Panel” in Section 4 Appliances for further information on the
monitor panel and checking tank levels.
See “Specifications” in Section 1 Introduction for tank capacities for your model.
HOLDING TANK HEATER
Black Waste Tank Flush Inlet
(Located on left sidewall)
-Typical View
4. Turn the water on to begin flushing. Allow
water to run for about three minutes.
5. Disconnect garden hose from flushing system
and close Black Waste Tank Drain valve.
–If Equipped
Your coach may be equipped with black water
and gray water holding tank heaters to allow use
of waste utilities in freezing temperatures. The
holding tank heater power switch is located near
the monitor panel. The illuminated switch will
glow when the power is on.
Using On-Site Sewer Hook-Ups
The sewage drain hose may remain attached to
the dump outlet and be routed out the bottom of
the compartment while the motorhome is parked
and connected to an on-site sewage hook-up.
WARNING
Service inlet access must be closed when
utility connections are not in use.
When using a sewer hook-up, keep the dump
valves closed until a tank becomes full or when
preparing to leave the site. This keeps the solids
in suspension, allowing them to be carried out
with the liquids when the dump valve is opened.
If the valve is left open, the liquids will drain off,
leaving solids in the tank. Should this
accidentally happen, disconnect the hose, fill the
tank about half full with water, and drive a few
miles to dislodge the solids. A few starts and
stops will aid in the process. Then reconnect the
hose and drain in the normal manner.
7-8
Holding Tank Heater Switch
(Located near monitor panel)
-Typical View
DO NOT operate the holding tank heater
unless you are providing a supplemental 12-volt
power source to recharge the house batteries.
This means either the shoreline cord must be
plugged into a 120-volt source, the auxiliary
generator must be operating, or the chassis
engine must be running (such as when driving
down the road). This will prevent excessive
discharge of the house battery.
NOTE: The holding tank heater pads are
electrical resistant-type heating
elements. This type of heating element
SECTION 7 –
PLUMBING
typically uses a large amount of current
while operating. If the tank heaters are
used without a recharging source, they
will drain the house batteries in a
relatively short period. Typically, the
batteries would not support overnight
heating without a supplemental charging
source.
WATERLINE & TANK DRAIN
VALVES
The water drain valves are used to drain water
from the water tank and the water supply lines
when preparing the motorhome for storage or
when sanitizing the water system.
To open or close the drain valves, turn the
handles in the directions indicated by the
following illustration.
See the drain valve location chart at the end of
this section for locations on your model.
Waterline Drain Valve
-Typical View
OFF
ON
Water Tank Drain Valve
(Typical)
Normal Operation
Drain Open
•The Water Tank Drain Valve has on/off
indicator arrows.
•Rotate the shut-off valve “clockwise” to
turn valve OFF.
•Rotate the shut-off valve “counterclockwise” to turn valve ON.
All Open
Waterline Drain Valves
(Typical)
Water Tank Drain Valve
-Typical View
7-9
SECTION 7 –
PLUMBING
WATER HEATER BYPASS AND
ANTIFREEZE SIPHON VALVES
–If Equipped
Your coach may be equipped with a Water
Heater Bypass valve and an Antifreeze Siphon
(Winterization) valve for winterizing waterlines
using RV antifreeze.
Turn the handle as shown to either bypass or
flow mode.
Refer to the “Water System Drain Valve
Locations” chart at the end of this section for
locations on your model.
Normal
Flow
2. Drain Fresh Water Tank and Waterlines.
Open all waterline drain valves and drain
fresh water tank. (See “Water System Drain
Valve Locations” chart at the end of this
section for locations of drain valves on your
model).
3. Drain Exterior Shower/Wash Station.
Open exterior shower knobs, then point
shower hose toward ground and squeeze
handle to drain any water left in the shower
line. Also, place the tip of your finger into the
city water inlet and gently press the backflow
valve “button” in the center of the inlet to
drain any water trapped in the inlet line.
4. Remove the Ice Maker Water Filter
Cartridge (if equipped). Remove the ice
maker filter cartridge from the filter assembly
below the galley sink.
(If your coach is not equipped with an ice
maker, proceed to the next numbered step).
By-Pass
Mode
C AU T I ON
Leave bypass valve handle in NORMAL
FLOW position if draining water and
blowing out waterlines. Place in BYPASS
position ONLY when using antifreeze
solution in waterlines.
WINTERIZING PROCEDURE
You can winterize the water and plumbing
system of your coach using the following
method.
Blow Out Procedure
(Drain and purge waterlines using
compressed air)
1. Level the Motorhome. If the coach is not
level, there may be “low points” in waterlines
that can trap water in the lines and prevent it
from draining properly.
7-10
Ice Maker Water Filter Assembly
(Located below galley sink)
• Twist the filter cartridge “counterclockwise” about a quarter-turn and pull it
down and out of the filter socket.
NOTE: The water filter head has a built-in
bypass. No separate diverter plug is
needed.
5. Open Faucets. Turn on the water pump and
open all sink faucets and shower head knobs.
Leave open after water stops flowing.
SECTION 7 –
PLUMBING
6. Drain Toilet. Press the toilet flush pedal and
hold until water stops flowing in the toilet.
Then turn water pump switch off.
7. Drain Water Heater. Turn off the water
heater power switch before draining the water
heater tank to avoid damage to the heating
element. Drain the water heater by removing
the plug from the base of the water heater tank,
accessible from the outside of the coach.
(Requires socket and ratchet).
Water Heater Drain Plug
(Remove with socket)
C AU T I ON
Hot water can escape from tank causing
injury. Operate relief valve or remove
drain plug only when the tank water is
cold.
• Also, open the Pressure-Temperature Relief
valve at the top right portion of the tank to
prevent air locking in the tank while
draining.
Pressure-Temperature
Relief Valve
(Lift handle only when water heater is cold)
8. Connect Air Pressure. After water has
stopped draining at all faucets and drain
valves, leave faucets open and connect a
“blow-out” plug to the city water connection
on the coach. Then use a compressed air hose
regulated to 30 psi or less to force air through
the system. A “blow-out” plug can be
purchased at any Winnebago Industries®
dealer.
City Water
Connection
Fresh Water
Inlet
Blow-out
Plug
Air Hose
NOTICE
Limit air pressure to 30 psi to avoid
damage to equipment.
NOTE: DO NOT burst air into the system. This
can damage the water pump. It is better
to let air in slowly.
9. Let air flow for five minutes until water is
completely drained out of faucets and drain
valves. Then close faucets one at a time.
7-11
SECTION 7 –
PLUMBING
10. Drain Toilet. Operate and hold toilet flush
lever until water is completely drained from
toilet.
11. Turn air pressure off. Disconnect water
purge adapters. Recap the city water inlet to
avoid contamination by dirt or insects.
After Disconnecting Air Pressure
12. Close all waterline drains, tank drain valves,
and all faucets to avoid contamination by dirt,
insects, or rodents.
13. Reinstall the Water Heater drain plug and
close the P-T Relief Valve.
14. Pour about one cup of non-toxic RV antifreeze
down the galley sink drain(s), bathroom
lavatory sink drain, and shower drain. This
fills the drain traps to prevent holding tank
odors from entering the coach during storage.
NOTE: It is not necessary to add antifreeze to
the toilet since the flush valve will be
closed.
Do not add automotive antifreeze or
caustic chemicals such as bleach or
laundry detergents into the toilet bowl or
holding tanks. Although these products
may have a deodorizing effect, they may
damage plastic and rubber parts in the
system.
15. Empty the water pump strainer filter bowl to
avoid water freezing and cracking the filter
bowl. See “Water Pump” previously in this
section.
Dump and Clean Holding Tanks
16. Completely drain the sewage and waste water
holding tanks at an approved waste disposal
site. Drain the sewage tank first so the
following waste water can rinse any waste
solids from the sewage drain outlet and sewer
hose.
17. Close dump valves and refit the dust cap onto
the sewage drain outlet.
This will inhibit rust formation on valve shafts
and prevent entry and contamination by
airborne debris, insects, and rodents.
7-12
Your drainage and fresh water systems are
now winterized.
See instructions for removal from storage in
Section 11 - Maintenance and Storage.
WINTERIZING OPTIONAL
APPLIANCES
–If Equipped
Winterizing Ice Maker
1. Drain coach waterlines.
2. Unscrew the water supply line from the
bottom of the water inlet valve and drain any
water left in the line. This connection is
located in the refrigerator service
compartment on the outside of the coach. See
“Refrigerator Service Access Compartment”
in Section 4 - Appliances and Systems.
Ice Maker Water Supply Connection
-Typical View
3. Let the ice maker run through a cycle, then
raise the shut-off arm.
4. Be sure water has drained from ice maker
supply line, then reconnect to inlet valve.
5. Ice maker is now winterized.
To use Ice Maker again:
Flush antifreeze from the waterlines, then
1. Close all drain valves.
2. Turn the water supply on.
3. Be sure the ice bin is in place and the
automatic shut-off arm is down.
SECTION 7 –
PLUMBING
4. Let the refrigerator cool down to ice making
temperature. Remember, this can take up to 24
hours.
5. Let the ice maker cycle and dump the first
batch of ice.
7-13
SECTION 7 –
PLUMBING
WATER SYSTEM DRAIN VALVE LOCATIONS
MODEL
22M
22R
25B
SYSTEM
Waterlines
•
Water Tank
•
Water Heater
•
Water Heater
Bypass Valve
Waterlines
•
Behind access door at bottom of pantry.
•
Water Tank
•
Water Heater
•
Water Heater
Bypass Valve
Waterlines
•
Two (2) valves beneath the rear dinette seat.
Remove panel to access.
Also, place the tip of your finger inside the city water
connection and gently press the backflow valve
(small “button” in center of connector) to drain any
water left in the city waterline.
One (1) valve beneath the bed. Lift mattress to
expose access hole.
Drain plug on outside of coach behind service door.
Use socket to remove drain plug.
Under rear dinette seat. Remove panel to access.
•
•
7-14
Water Tank
•
Water Heater
•
Water Heater
Bypass Valve
•
DRAIN VALVE LOCATIONS
Three (3) valves beneath the rear dinette seat.
Remove panel to access.
Also, place the tip of your finger inside the city water
connection and gently press the backflow valve
(small “button” in center of connector) to drain any
water left in the city waterline.
One (1) valve behind access door at bottom of
pantry.
Drain plug on outside of coach behind service door.
Use socket to remove drain plug.
One (1) valve by water heater. Access through return
air grille under stove.
Two (2) valves under wardrobe. Access by removing
bottom drawer of wardrobe.
Also, place the tip of your finger inside the city water
connection and gently press the backflow valve
(small “button” in center of connector) to drain any
water left in the city waterline.
One (1) valve beneath the bed. Lift mattress to
expose access hole.
Drain plug on outside of coach behind service door.
Use socket to remove drain plug.
Beneath galley sink. Access by removing bottom
drawer of galley cabinet.
SECTION 7 –
PLUMBING
26A
31D
31G
Waterlines
•
Water Tank
•
Water Heater
•
Water Heater
Bypass Valve
Waterlines
•
Water Tank
•
Water Heater
•
Water Heater
Bypass Valve
Waterlines
•
Water Tank
•
Water Heater
•
Water Heater
Bypass Valve
•
•
•
Two (2) valves beneath galley sink. Remove panel to
access.
Also, place the tip of your finger inside the city water
connection and gently press the backflow valve
(small “button” in center of connector) to drain any
water left in the city waterline.
One (1) valve beneath the bed. Extend the rear bed
slideout, remove mattress from bed, and lift hinged
bed board to access.
Drain plug on outside of coach behind service door.
Use socket to remove drain plug.
Under range/oven. Remove furnace grate to access.
Two (2) valves beneath lavatory cabinet. Remove
panel to access.
Also, place the tip of your finger inside the city water
connection and gently press the backflow valve
(small “button” in center of connector) to drain any
water left in the city waterline.
One (1) valve beneath the bed. Remove panel at foot
of bed to access.
Drain plug on outside of coach behind service door.
Use socket to remove drain plug.
Beneath galley sink. Remove galley drawers to
access.
Two (2) valves beneath the bed. Lift mattress to
expose access hole.
Also, place the tip of your finger inside the city water
connection and gently press the backflow valve
(small “button” in center of connector) to drain any
water left in the city waterline.
One (1) valve beneath the bed. Lift mattress to
expose access hole.
Drain plug on outside of coach behind service door.
Use socket to remove drain plug.
Beneath galley sink. Access through galley cabinet
doors.
7-15
SECTION 7 –
PLUMBING
31K
7-16
Waterlines
•
Water Tank
•
Water Heater
•
Water Heater
Bypass Valve
•
Two (2) valves in galley. Remove bottom drawer of
galley and/or panel under sink.
Also, place the tip of your finger inside the city water
connection and gently press the backflow valve
(small “button” in center of connector) to drain any
water left in the city waterline.
One (1) valve beneath the bed. Lift mattress to
expose access hole.
Drain plug on outside of coach behind service door.
Use socket to remove drain plug.
Under range/oven. Remove return air grille to
access.
SECTION 8 – ENTERTAINMENT
TV – (SWIVEL)
–If Equipped
(Typical View - your coach may vary in
appearance according to floorplan)
Your coach may be equipped with a TV
swivel/telescoping mechanism, which allows
you to angle the TV to best suit your viewing
needs.
To Swivel TV
1. Pull the black strap (located on back side of
TV) straight down while pulling the TV
outward to release the TV from the mounting
bracket. Pivot TV to desired location.
Grasp TV case at
midpoint edges to
rotate and lock
Further Information
See the television manufacturer’s user guide
provided in your InfoCase for complete operating
instructions.
2. Grasp TV case at midpoint edges then rotate
TV back to center position. Press straight back
towards the wall. You will hear a “click” when
the TV is secured into locked position.
NOTE: For your convenience, we have also
included a handy, tear-out version of this
“A/V System Basic Operation” guide in
Section 8 of your Operator’s Manual
Supplement.
See your InfoCase for specific operating
guides for audio and video components.
DVD PLAYER
–If Equipped
NOTICE
Do not push on TV screen. Handle by
TV case at midpoint edges to prevent TV
damage.
The player is connected directly to the TV
with a composite video cable (red, yellow, white)
or HDMI cable.
Set TV Video Input
•
•
Turn TV and DVD player ON.
Press the SOURCE button on the TV or the
remote to select “VIDEO” input.
8-1
5 - DASH / AUTO
AUDIO/VIDEO SYSTEM BASIC
OPERATION
SECTION 8 –
ENTERTAINMENT
•
The TV screen will display the
DVD player logo when the correct
input is selected.
Exterior Speaker System
Play DVD
•
•
•
•
•
•
Press “OPEN/CLOSE” on DVD player to
open tray.
Insert a DVD “face up” on to tray and press
“OPEN/CLOSE” to close tray.
The DVD will begin to load automatically.
The TV screen will typically display
“Reading” or “Loading”.
The DVD may load directly to the main
title/menu screen or it may begin to play
previews. You may be able to skip previews if
desired by pressing the chapter “advance”
button on the DVD remote until you see the
main menu screen.
When the main menu screen appears, use the
arrow buttons on the DVD player remote to
select the desired entry or press the “+” or
PLAY buttons on the DVD player remote (or
“Play” button on DVD player) to begin
playing the feature.
Volume is adjusted with the DVD remote or
TV remote.
Further Information
See the manufacturer’s quick reference guide
provided in your InfoCase for complete feature
descriptions and operating instructions.
Interior Speaker select Zone A
•
Set TV Video Input
•
•
•
8-2
Turn TV and Radio/DVD player ON.
Press the MODE button on the TV or the
SOURCE button on the remote to select
“INPUT 2”.
The TV screen will
display the DVD player
logo when the correct
input is selected.
Play DVD
•
•
•
DVD PLAYER
–If Equipped
The DVD Player is a selectable function of the
multi-featured audio system. The player unit
contains DVD/CD, MP3, AM/FM, USB, and
Bluetooth Stereo. It also accepts portable audio
player inputs and functions as an alarm clock.
This stereo receives Bluetooth streaming
audio from Bluetooth enabled audio sources such
as a cellphone.
The player is connected directly to the TV and
can output sound to either the stereo speakers in
the TV or to the Exterior speakers.
To connect or disconnect the interior speaker
system, press Zones and select Zone A, B, or
C to turn on/off.
•
•
Insert a DVD “face up” into slot on lower face
of the player.
The DVD will begin to load automatically.
The TV screen will typically display
“Reading” or “Loading”.
The DVD may load directly to the main
title/menu screen or it may begin to play
previews. You may be able to skip previews if
desired by pressing the “Next” button on the
DVD remote until you see the main menu
screen.
When the main menu screen appears, press
the “Enter” button on the remote or “Play/
Pause” button on DVD player to begin
playing the main feature. Use the arrow
buttons on the DVD remote to select another
feature to play.
Volume is adjusted with the DVD remote.
SECTION 8 –
ENTERTAINMENT
TV Sound through Exterior
Speakers
When watching TV programs alone, the TV
normally plays sound through its own built-in
stereo speakers. If you wish to connect TV stereo
sound output to the Exterior speakers for a richer
sound quality, follow these steps:
1. Turn the TV ON.
2. Press the Mode input selection button (located
in the top right corner of radio) and choose
AUX. This will route the TV stereo sound
output through the Radio/DVD Player and out
to the Deluxe Sound speakers.
3. Select TV channels and adjust volume using
the TV remote.
•
•
Play DVD
•
•
•
Further Information
See the manufacturer’s quick reference guide
provided in your InfoCase for complete feature
descriptions and operating instructions.
•
DVD PLAYER
–If Equipped
The DVD Player is a selectable function of the
multi-featured audio system. The player unit
contains DVD/CD, MP3, AM/FM, USB, and
Bluetooth Stereo. It also accepts portable audio
player inputs and functions as an alarm clock.
This stereo receives Bluetooth streaming
audio from Bluetooth enabled audio sources such
as a cellphone.
The player is connected directly to the TV and
can output sound to either the stereo speakers in
the TV or to the Exterior speakers.
Exterior Speaker System
•
To connect or disconnect the exterior speaker
system, press SPEAKER A.
Set TV Video Input
•
Turn TV and Radio/DVD player ON.
Press the MODE button on the TV or the
SOURCE button on the remote to select
“INPUT 2”.
The TV screen will display the
DVD player logo when the correct
input is selected.
•
Insert a DVD “face up” into slot on lower face
of the player.
The DVD will begin to load automatically.
The TV screen will typically display
“Reading” or “Loading”.
The DVD may load directly to the main
title/menu screen or it may begin to play
previews. You may be able to skip previews if
desired by pressing the “Next” button on the
DVD remote until you see the main menu
screen.
When the main menu screen appears, press
the “Enter” button on the remote or “Play/
Pause” button on DVD player to begin
playing the main feature. Use the arrow
buttons on the DVD remote to select another
feature to play.
Volume is adjusted with the DVD remote.
TV Sound through Exterior
Speakers
When watching TV programs alone, the TV
normally plays sound through its own built-in
stereo speakers. If you wish to connect TV stereo
sound output to the Exterior speakers for a richer
sound quality, follow these steps:
1. Turn the TV ON.
2. Press the AUX input selection button (located
just below the display on the face of the Radio/
DVD Player.) This will route the TV stereo
sound output through the Radio/DVD Player
and out to the Exterior speakers.
3. Select TV channels and adjust volume using
the TV remote.
Further Information
See the manufacturer’s quick reference guide
provided in your InfoCase for complete feature
descriptions and operating instructions.
8-3
SECTION 8 –
ENTERTAINMENT
TV ANTENNA – DIGITAL
(Jack®
Digital HDTV Over-the-Air
Antenna)
–If Equipped
Your coach is featured with a digital antenna,
which provides crystal clear digital HD reception
of over-the-air channels in addition to superior
broad reception range.
The digital antenna is equipped with a built-in
amplifier for maximum VHF and UHF
programming.
WARNING
Never allow the antenna to touch
electrical power lines or any other
electrical wires.
Operating the Digital Antenna
1. Turn the Digital Antenna Power Switch ON.
Digital Antenna Power Switch
(Located in an overhead cabinet or
mounted on a wall near the TV)
2. Turn ON the Signal Meter Power switch
(located on the side of the Signal Meter).
•Signal Meter
Power Switch
•Release
Button
•Attenuator Dial
•Rotational Knob (arrow
indicates which direction
antenna is pointing)
Digital Antenna Signal Meter
(Located on ceiling)
3. Rotate the Attenuator Dial fully
CLOCKWISE.
4. Press Release Button on the Rotational Knob
and rotate antenna (until maximum number of
LED lights illuminate on the Signal Meter).
NOTE: LED lights will illuminate from left to
right. All LED lights may not illuminate,
depending on signal strength.
5. Rotate Attenuator Dial COUNTERCLOCKWISE until the last illuminated LED
light flickers.
6. Rotate antenna to illuminate the last flickering
LED light.
7. Repeat Steps 5 and 6 to pinpoint signal
reception.
NOTE: Refer to television manufacturer’s
instructions to scan for available
channels.
Further Information
See the antenna manufacturer’s user guide
provided in your InfoCase for complete operating
and maintenance information.
8-4
SECTION 8 –
ENTERTAINMENT
TV ANTENNA
–If Equipped
The TV antenna on your motorhome is a
stationary omnidirectional design. The antenna
provides reception of VHF/UHF TV channels. A
built-in signal amplifier designed to strengthen
signals, is controlled by a power switch built into
the optional video selector panel or on a wall
plate assembly.
WARNING
Never allow the antenna to touch
electrical power lines or any other
electrical wires. Death or serious injury
can occur.
Further Information
See the antenna manufacturer’s operation,
care, and maintenance information in your
InfoCase.
• Power
Switch
TV Signal Amplifier Power Switch
(Located in an overhead cabinet or mounted
on a wall near the TV)
-Typical View
EXTERIOR CABLE TV
CONNECTION
The exterior cable TV connection receptacle
on your coach provides connection for use of a
TV for your outdoor entertainment..
TV SIGNAL AMPLIFIER
The TV Signal Amplifier is built into the
antenna and can be turned on or off with a power
switch.
An indicator light will illuminate when the
switch is on and the signal amplifier is active.
Exterior Cable TV Connection
(Located near entrance door)
-Typical View
EXTERIOR ENTERTAINMENT
CENTER (ADJUSTABLE)
–If Equipped
Your coach may be equipped with an Exterior
Entertainment Center, which contains Audio/
Video Connections for your outdoor listening or
viewing pleasure.
8-5
SECTION 8 –
ENTERTAINMENT
NOTE: These electronic devices are not
designed to be waterproof. Please take
measures to prevent rain or other
precipitation from entering the
entertainment center by closing the
compartment door or ensuring that an
awning will prevent entrance of
precipitation.
To Swivel TV
-Typical View
1. Pull the black strap (located on back side of
TV) straight down to release the TV from the
mounting bracket.
-Typical View
2. Pull the TV out and pivot to desired position.
8-6
3. Rotate TV back to center position and press
straight back. You will hear a “click” when the
TV is secured into locked position.
Further Information
Please read the manufacturer’s user guide in
your InfoCase for complete operating
instructions.
SECTION 9 – FURNITURE AND SOFTGOODS
CAB SEAT LOUNGE CUSHION
–If Equipped
(Typical View – Your coach may differ in
appearance)
The driver and co-pilot seats may feature a
Lounge Seat Cushion which provides increased
seat height and added comfort while in the lounge
seating position. The Lounge Seat Cushion must
not be used when the vehicle is in motion.
Lounge Seat Latched
-Typical View
WARNING
SLEEPING FACILITIES
1. Swivel seat to desired position.
2. Place Lounge Seat Cushion on seat.
WARNING
Sleeping facilities are not intended for use
while vehicle is in motion. For safety,
passengers must use safety belted
seating positions while vehicle is in
motion.
FRONT OVERHEAD BUNK
–If Equipped
(Typical View – Your coach may differ in
appearance)
Lounge Seat Cushion
-Typical View
The overhead front bunk is located above the
driver’s compartment. The rear mattress section
can be stacked on top of the front section for
storage while traveling or when not in use.
Before Using Bunk Ladder
•
3. Route the Lounge Seat Cushion Strap around
the back of the seat and latch. Pull strap to
tighten.
Inspect the ladder to make sure it is not
damaged. Never use a damaged ladder.
9-1
5 - DASH / AUTO
Do not use the Lounge Seat Cushion
while the vehicle is in motion. Failure to
comply may result in injuries.
SECTION 9 –
FURNITURE AND SOFTGOODS
•
Keep the rungs of the ladder clean and dry
while in use. Do not step onto the rungs if the
rungs are wet, or if your shoes are wet or carry
debris that could result in a loss of footing.
Never ignore warning labels or weight limits
defined on your ladder. The following
warning label is located on or near the ladder:
•
Attaching Bunk Ladder
1. Remove ladder from travel straps.
2. Align ends of ladder with the mattress retainer
brackets (as shown in the following photos).
3. Make sure top of ladder is properly engaged
onto retainer brackets and ladder is resting
firmly on floor before using.
C AU T I ON
To avoid injury, never use the bunk ladder
in any other manner or for any other
purpose than described in the following
instructions.
WARNING
Do not exceed 225 lbs. maximum weight capacity.
Misuse of ladder could result in death or serious injury.
See Operators Manual before using ladder.
•
•
•
•
•
•
•
Maximum Capacity: 225 lbs.
Do not overload. Ladder is intended for one
person.
Make sure you are physically capable to
safely use the ladder. Strength, flexibility and
stability are required.
Grasp the side rails firmly and always use
both hands as you climb the ladder. Keep your
body centered between the side rails. Do not
over-reach.
To protect children, do not leave the ladder
set up and unattended.
Always store the ladder in a safe and dry
location when not in use. Stow properly while
in transit.
Do not store items on the ladder. You could
damage the ladder.
To Use the Bunk Ladder
The top of the bunk ladder must be hooked
onto the brackets on the rear edge of the bunk
mattress as shown.
9-2
•
•
Reverse steps to store ladder.
Straps are provided on the mattress section to
secure and store the ladder while traveling or
when not in use.
SECTION 9 –
FURNITURE AND SOFTGOODS
SOFA/BED CONVERSION
SOFA/SLEEPER
–If Equipped
(Typical View – Your coach may differ in
appearance)
–If Equipped
(Typical View – Your coach may differ in
appearance)
Sofa to Bed
•
Pull OUT on security latch (located on front of
sofa) to release sofa seat.
WARNING
Stow sofa extensions before retracting
slide rooms. Failure to observe can cause
injury and will cause equipment damage.
Sofa to Bed
1. Remove sofa seat back, set aside.
Security Latch
(Located on front of sofa)
- Pull OUT to release
•
•
Lift the front edge of the sofa seat upward and
outward from the wall while gently pushing
downward on the backrest until the cushions
lie flat.
The bed is now ready for use.
2. Pull sofa seat UP and OUT.
Bed to Sofa
•
Push the front edge of the sofa seat toward the
wall while lifting upward on the backrest until
the sofa is fully seated against the wall and
security latch “clicks” into locked position.
9-3
SECTION 9 –
FURNITURE AND SOFTGOODS
3. Pull sofa support back in downward motion.
DINETTE/BED CONVERSION –
DREAM DINETTE™
–If Equipped
(Typical View – Your coach may differ in
appearance)
Dinette to Bed
1. Release the lock rod on the bottom of the
dinette table by pulling down.
Lock Rod
4. Bed is now ready for use.
2. Lift the dinette cushions upward and push
table straight down.
5. Reverse steps to store bed into sofa position.
6. When the bed is back in the sofa position,
close the two (2) doors located on each end of
the sofa.
3. Rotate lock rod up to secure table in the
lowered position.
Lock Rod
(locked
position)
9-4
SECTION 9 –
FURNITURE AND SOFTGOODS
4. Arrange dinette cushions to cover bed area.
Dinette to Bed
NOTE: Additional bolsters may be included with
your dinette to cover bed area.
1. Remove both dinette back cushions and set
aside.
2. Lift both dinette seat cushions upward.
Reverse steps to convert back into dinette
seating.
Once the table is up, engage the lock rod by
pushing the lock rod up.
WARNING
Failure to engage the lock rod when the
table is raised may result in injury.
3. Release the table leg from the floor support
bracket.
DINETTE/BED CONVERSION
–If Equipped
(Typical View – Your coach may differ in
appearance)
Floor
Support
Bracket
9-5
SECTION 9 –
FURNITURE AND SOFTGOODS
4. Release the catch on the table leg brace and
fold the leg up against the bottom of the table.
Table Leg
Catch
5. Remove the table from the wall support
bracket by lifting the end of the table.
Wall
Support
Bed to Dinette
Reverse steps to convert back into dinette
seating.
Once the table is reattached onto the wall
support, make sure the table leg is secured into
the floor support bracket and the leg brace is
locked.
Floor
Support
Bracket
Table
Bracket
6. Then lower the table to rest on the cleats
attached to each dinette bench.
U-SHAPED DINETTE/BED
CONVERSION
7. Arrange dinette cushions to cover bed area.
NOTE: Additional bolsters may be included with
your dinette to cover bed area.
9-6
–If Equipped
(Typical View – Your coach may differ in
appearance)
The U-Shaped Dinette can be converted into
additional sleeping space when needed by
lowering the dinette table and arranging the
dinette cushions.
1. Get a partner to help you lift the table top
upward off the support tubes and set the table
top edgewise onto the floor to remove the
table leg tubes.
SECTION 9 –
FURNITURE AND SOFTGOODS
U-SHAPED DINETTE/BED
CONVERSION
–If Equipped
(Typical View – Your coach may differ in
appearance)
The U-Shaped Dinette can be converted into
additional sleeping space when needed by
lowering the dinette table and arranging the
dinette cushions.
1. Turn knob to loosen table top from pedestal.
2. Pull the table leg tubes from the floor or table
sockets and store beneath dinette seat.
3. Place the table top onto the ledge of the dinette
seat.
Place table
top onto
ledge.
2. Get a partner to help you lift the table top
upward off the support tube and set the table
top edgewise onto the floor to remove the
table leg tube.
3. Pull the table leg tube from the floor or table
socket and store beneath dinette seat.
4. Place the table top onto the ledge of the dinette
seat.
4. Place the center back dinette cushion into
place over the table to complete the bed
conversion.
Reverse steps to reassemble to dinette
configuration.
Place table
top onto
ledge.
9-7
SECTION 9 –
FURNITURE AND SOFTGOODS
5. Arrange cushions to cover bed area.
NOTE: Use the back dinette seat cushions and
two bolster cushions to cover the dining
table.
Reverse steps to reassemble to dinette
configuration.
DINETTE FLIP-UP FOOTRESTS
U-SHAPED DINETTE/BED
CONVERSION
–If Equipped
(Typical View – Your coach may differ in
appearance)
The U-Shaped Dinette can be converted into
additional sleeping space when needed by
lowering the dinette table and arranging the
dinette cushions.
1. Release both latches on the table leg to unlock.
–If Equipped
(Typical View – Your coach may differ in
appearance)
1. To Extend: Pull footrest up until it locks into
position.
2. To Store: Pull footrest all the way up until the
locking arms release and lower into stored
position.
2. Lift edges of the dinette cushions up and push
the dinette table straight down. Make sure the
table is lowered as far as it will go so when
arranging the cushions to cover the bed area,
they are even with the other dinette cushions.
NOTE: You may find it easier to remove the
dinette cushions completely before
lowering the table, especially if just one
person is converting the dinette into bed
position.
9-8
SECTION 9 –
FURNITURE AND SOFTGOODS
3. Secure both latches on the table leg to lock in
lowered position.
BUNK BEDS/WARDROBE
CONVERSION
–If Equipped
(Typical View – Your coach may differ in
appearance)
Your coach may be equipped with bunk beds
which convert easily into a wardrobe.
4. Arrange cushions to cover bed area.
NOTE: Use the back dinette seat cushion and
two bolster cushions to cover the dining
table.
Reverse steps to reassemble to dinette
configuration. Once the table is up, secure both
latches on the table leg.
WARNING
Failure to engage both latches when the
table is raised may result in injury.
NOTE: This low bunk design may be accessed
without the use of a ladder. If needed, a
multi-purpose step stool may be used.
• Maximum Capacity: 300 lbs.
• To avoid injury to young children, do not
leave them unattended on the bunk.
Bunk Beds to Wardrobe
1. Lift top mattress and bunk board to the upright
position. Engage security lock located on the
front bunk cabinet wall.
NOTE: Ensure that security lock (located on
front bunk cabinet wall) is fully engaged.
Reverse steps to reassemble to bunk bed
configuration.
PLEATED BLINDS
–If Equipped
Your coach may feature pleated window
blinds for nighttime privacy and daytime room
darkening purposes.
They are raised or lowered by grasping the
bottom edge of the blind and moving it up or
down by hand.
A constant-tension cord system holds them at
the desired level without slipping.
9-9
SECTION 9 –
FURNITURE AND SOFTGOODS
Tension Adjustment
•
The tension of the pleated blinds can be
adjusted if they become loose and will not stay up
when raised, or they are too tight and are difficult
to raise and lower.
The tension cords are attached to spools at the
lower corners of the blinds as shown in the
following photo.
ROLLER SHADES (MANUAL) –
SOLAR/BLACKOUT
Reapply starch periodically (every few
months) as needed.
–If Equipped
Your coach may feature two-stage day/night
roller shades that provide both solar heat
protection and light-blocking capabilities.
The shade can easily be lowered by hand to
any position, then retracted with a slight
downward pull movement. When raising the
shade, there is no need to hold onto the bottom of
the shade - just simply let it go and it will rise at
a slow, controlled rate.
You can pre-set the auto-stop positioning of
your shade, which allows your shade to retract to
a cushioned stop, at the positioning of your
choice.
To Tighten Tension
Wrap the tension cords around the mounting
spools, one turn at a time, at both ends of the
shade. Check tension by raising and lowering a
few times. Repeat as necessary to obtain the
desired tension. Do not over-tighten.
To loosen tension
Unwrap the guide cords from the spools, one
turn at a time, until desired tension is achieved.
Preserving Shape
The pleated blinds are made using high
quality materials that are designed and woven to
retain their shape throughout their useful life.
They may lose their crisp shape, however, if left
in a lowered position for an extended period of
time without being raised periodically. If this
happens, the pleats can be restored using this
simple method.
• With the blind fully lowered, dampen the
entire area of the pleats with a good quality
laundry spray starch.
• Raise the blind fully while still damp and let it
remain in the raised position for about 24
hours.
9-10
-Typical View
Further Information
For further operating information and care
instructions, see the manufacturer’s user guide
provided in your InfoCase.
SECTION 9 –
FURNITURE AND SOFTGOODS
WOOD FURNITURE AND
CABINETRY
–If Equipped
People are drawn to the natural beauty of
wood. At Winnebago Industries®, our craftsmen
work with the art found in each piece of wood to
create cabinets of superior quality, backed by the
Winnebago Industries warranty.
• Oak is a strong, open-grained hardwood that
ranges in color from white to pink and reddish
tones. Streaks of green, yellow, and even
black may appear due to mineral deposits.
Oak may also contain wormholes and wild,
varying grain patterns. This distinct graining
is considered a desirable quality and has made
oak one of the most popular woods used for
cabinetry.
• Maple is a close-grained hardwood that is
predominately white to creamy-white in
color, with occasional reddish-brown tones.
While maple typically features uniform
graining as compared to other wood species,
characteristic markings may include fine
brown lines, wavy or curly graining, bird's eye
dots and mineral streaks. These traits are
natural and serve to enhance maple's natural
beauty.
• Cherry is characterized by its red undertones,
but may vary in color from white to a deep,
rich brown. Cherry is a close-grained wood
with fairly uniform texture, revealing pin
knots and curly graining. All wood will age
with time and the finish will darken. This is
especially true for cherry. This is a soughtafter quality in cherry cabinetry, and those
who select it expect this evolution.
No matter which species you chose for your
new Winnebago Industries motorhome
cabinetry, please keep in mind that no two pieces
of wood are exactly the same.
Stains are likely to exaggerate the difference
between open and closed grains and other
markings in wood. Grain variation and color
change should be expected. As hardwood ages, it
will darken when exposed to different types of
light. Color differences or changes in wood can
also be caused by exposure to harsh chemicals,
extreme heat, or other contributing external
conditions.
Any color change that occurs in both the finish
and the wood is considered part of the natural
aging process and is not to be considered defect
or damage.
Additionally, wood species exhibit other
defining characteristics, such as mineral
deposits/streaks, knots, sap runs, pin holes, and
wormholes. These markings make the wood
unique and contribute to its enduring beauty.
Therefore, since wood is a product of nature
and will have certain natural characteristics and
variances, they are not covered under the
warranty.
9-11
SECTION 10 – SLIDEOUT ROOMS AND LEVELING
SLIDEOUT ROOM LOCK
SYSTEM
SLIDEOUT ROOM OPERATION
– ELECTRIC
WARNING
Your motorhome may have more than
one slideout room. Understand which
switch operates which slideout room prior
to operation. Make sure all slideout rooms
are clear of people who could be harmed
or obstacles that could cause damage
prior to operating any slideout rooms.
Failure to observe can result in death or
serious injury.
Slideout rooms provide a spacious living area
at the push of a button.
Front slideout room switches are typically
located near the Systems Monitor Panel.
Location varies by model and floorplan.
Rear slideout switches are typically located on
a wall in the rear of the coach in or near the
slideout room. Location varies by model and
floorplan.
Slideout Switch
(Your coach may have one or more
slideout switches depending on model,
options, and available equipment)
-Typical View
C AU T I ON
Never drive the vehicle with a slideout
room extended!
The slideout room system uses 12-volt DC
motorized mechanisms with an electronic control
system to provide smooth operation and positive
weather seal.
NOTE: We recommend that you KEEP THE
ENGINE RUNNING WHILE
EXTENDING OR RETRACTING
SLIDEOUT ROOMS so the engine
alternator can provide maximum power
for proper operation of the slideout
mechanisms.
10-1
5 - DASH / AUTO
The ignition key must be placed in the on or
run position to operate the slideout room(s). The
park brake must be applied for the room(s) to run.
Winnebago recommends running the engine
whenever you run the slideout rooms in or out,
the engine alternator should insure the rooms
have adequate 12-volt DC power to operate
correctly.
SECTION 10 –
SLIDEOUT ROOMS AND LEVELING
To Retract Slideout Room
WARNING
CRUSH HAZARD. Keep people and
objects clear of the inside and outside of
the slideout room when operating. Failure
to comply could result in death or serious
injury.
To Extend Slideout Room
Before Extending!
• Level the coach and set the Parking Brake.
• Ensure exterior compartment doors are closed
so that they will not interfere with slideout
operation.
• Ensure driver and co-pilot seat backs are clear
of slideout trim before extending slideout.
• Check inside and outside the vehicle to make
sure that there are no people who could be
harmed or obstacles that could cause damage
due to room extension.
• If the slideout room has a couch or other
furniture, make sure no people or pets are
seated on them until the room has been fully
extended.
Before Retracting!
•
•
•
•
•
•
•
Extend Procedure:
See “Before Extending!” before proceeding.
•
Engage the parking brake.
•
Start the engine so the alternator can provide
maximum power for proper operation of
slideout mechanisms.
•
Press the Slideout Room “EXTEND/OUT”
switch and hold until the room is fully
extended, then release the switch.
To stop extending the room during operation,
release the button.
Remove and Secure the Ignition Key.
•
•
10-2
Be sure the coach is level and the Parking
Brake is set.
Ensure exterior compartment doors are closed
so that they will not interfere with slideout
operation.
Ensure driver and co-pilot seat backs are clear
of slideout trim before retracting slideout.
Check inside and outside the vehicle to make
sure that there are no people who could be
harmed or obstacles that could cause damage
due to room retraction.
Stow all furniture extensions before retracting
slideout rooms to avoid property damage.
If the slideout room has a couch or other
furniture, make sure no people or pets are
seated on them until the room has been fully
retracted.
Remove all items from the coach living room
floor and close cabinet doors and drawers. Be
sure there are no items at the end of the bed,
behind the driver seat, or protruding from
compartments, which could be crushed or
cause damage to floor covering or cabinets
when the room is retracted.
NOTICE
Because the slideout roof is drawn into
the interior of the coach when retracted,
be sure there is no debris, such as
excessive dirt, tree seeds, twigs, leaves,
etc. on the roof before retracting.
Retract Procedure:
See “Before Retracting!” before proceeding.
•
Engage the parking brake.
•
Start the engine so the alternator can provide
maximum power for proper operation of
slideout mechanisms.
SECTION 10 –
SLIDEOUT ROOMS AND LEVELING
•
•
•
Press the Slideout Room “RETRACT/IN”
switch and hold until the room is fully
retracted, then release the switch.
To stop retracting the room during operation,
release the button.
After the room is retracted, Remove and
Secure the Ignition Key.
•
The circuit breaker may be tripped. The
circuit breaker, labeled “Slideout Power” is
located on a panel on an interior wall of the
passenger side storage compartment just
behind or ahead of the entrance door.
Problems Retracting or Extending
the Room
SLIDEOUT ROOM – EXTREME
WEATHER PRECAUTION
Certain extreme weather conditions, such as
heavy rains, heavy snow, and high winds, or any
combination of these, could cause damage to the
slideout room cover-awning (if equipped) or
reduce effectiveness of the slideout room weather
seals.
Also, freezing rain and snow can prevent the
slideout cover-awning (if equipped) from closing
and may cause damage to the cover-awning,
slideout room, weather seals, and mechanisms.
To avoid potential damage, we recommend
retracting your slideout room during extreme
weather conditions.
SLIDEOUT ROOM
TROUBLESHOOTING (POWER
GEAR®) IN WALL SLIDEOUT
–If Equipped
Battery Voltage or Circuit Breaker
Problems
If the slideout room will not work:
• Turn the Chassis Battery Disconnect switch
OFF (leave off for 20 seconds) and then turn
ON again. This will, in many cases, reset
power to the slideout system.
• he chassis battery may be low on charge.
Press and Hold the Battery Boost switch
(located on the dash) while pressing the
interior slideout control switch. This
momentarily connects the house batteries to
assist in slideout room operation.
•Fault Code
LED
Slideout Control Box
(Located in a driver or passenger side
compartment, depending on model)
-Remove panel to access
If an error is detected on your slide system, the
LED light on the control panel will blink an error
code. If an error code appears, see the In Wall
Slideout manufacturer’s user guide in your
InfoCase to determine the problem. The error
code must be cleared prior to operating the room.
Further Information
See the In Wall slideout room operating guide
included in your InfoCase for further instructions
and troubleshooting information.
SLIDEOUT EMERGENCY
RETRACTION (POWER GEAR®)
IN WALL SLIDEOUT
–If Equipped
If the slideout mechanism is malfunctioning
and the room will not retract using the interior
control switch, see the In Wall Slideout Room
operating guide included in your InfoCase for
further instructions and troubleshooting
information.
10-3
SECTION 10 –
SLIDEOUT ROOMS AND LEVELING
GENERAL SLIDEOUT CARE
•
•
•
•
Keep slideout room seals clean.
Clean the floors inside the coach before
retracting the slideout room to avoid floor
scratches or carpet pile snags.
Wipe outer slideout room seals occasionally
with talc or 303 brand protectant for smooth,
quiet operation.
See your authorized dealer for regular
maintenance and service of the slideout
mechanism.
raising the front end rather than the rear.
Since only the rear wheels are locked
while in PARK, raising either one or both
of the rear wheels off the ground could
allow the vehicle to roll off the jacks.
Slideout Room Seal Care and
Maintenance
While most household cleaners work well for
cleaning slideout room seals, certain chemical
agents may cause the seals to degrade. Typically,
409® and Lysol® type products work well. Use a
product, such as Armor All® to keep seals soft.
In addition, certain caulks and sealers may
include chemicals that may adversely effect the
performance of the seals. See your authorized
dealer for caulks and sealers recommended for
your coach.
LEVELING SYSTEM
–If Equipped
The hydraulic leveling system makes
selecting a parking site easier and faster by
reducing the effect of uneven ground.
Hydraulic jacks raise the affected low corners
of the coach to make leveling “set up” faster and
easier for you.
The hydraulic Leveling System Control Pad is
located near the entrance door.
See the Leveling System Operator Manual
in your InfoCase for complete operating
instructions. It also contains additional
precautions, technical information, and
instructions for manual operation if a system
failure occurs.
NOTE: When parking at an uneven site, always
park the front of the motorhome to the
downhill side. This allows you to level by
10-4
WARNING
• Keep all people clear of the coach
while the leveling system is operating.
• When extending the rear stabilizers,
do not lift the wheels beyond ground
contact. This makes it possible for the
vehicle to roll unexpectedly forward (or
backward) off the jacks. This could
cause severe injury or death.
• Do not use the levelers on icy or slick
surfaces on which the foot pads may
slip.
• Do not use leveling jacks to support
the vehicle for service or tire changing.
• Do not use the leveler as an
emergency brake. They are not
designed for any type of vehicle
braking purpose.
• Never check for hydraulic fluid leaks
using your hands and/or any other
body part. The leaking fluid is under
pressure and is capable of cutting and
penetrating your skin, resulting in
severe injury.
SECTION 10 –
SLIDEOUT ROOMS AND LEVELING
Jacks Down Light
The “Jacks Down” reminder is intended to
warn you to retract your leveling jacks before
moving the vehicle. The light will come on and a
chime will sound when the ignition key is turned
to the On or Run positions if the jacks are down.
4. See the Leveling System user guide supplied
in your InfoCase for troubleshooting
instructions or operating the Leveling System
if jacks fail to retract or any other functions
fail.
Further Information
See the manufacturer’s user guide provided in
your InfoCase for complete operating
instructions, safety precautions, and
troubleshooting tips.
“Jacks Down” Light
(Located on dash)
-Typical View
NOTICE
• Do not try to drive vehicle unless
“TRAVEL” light is glowing with ignition
switch on.
• Do not rely only upon the warning
lights to indicate when jacks are up. It
is the owner’s responsibility to check
that all jacks are up before moving the
coach.
NOTE: If the Leveling Jacks should fail to
retract, see the MANUAL JACK
RETRACTION section of the Leveling
System Operator’s Manual included in
your InfoCase.
In The Event Of Accidental Jack
Extension
1. Bring the vehicle to a safe and complete stop
as soon as possible.
2. Turn the Leveling Systems power switch on
and press the “Auto Store” switch.
3. Visually inspect the vehicle undercarriage for
any problems.
10-5
SECTION 10 –
SLIDEOUT ROOMS AND LEVELING
CHECKING HYDRAULIC OIL
LEVEL
See the Leveling System Operator’s Manual
in your InfoCase for complete maintenance
instructions and information.
All maintenance should be done as part of the
normal servicing of the coach.
The hydraulic oil level should be checked
when the vehicle is first purchased, and then
twice a year - or more often if an oil leak develops
in the system.
The hydraulic pump is located inside a
passenger side mid-coach compartment.
of debris and contamination of hydraulic
oil in the reservoir, which could lead to
pump failure or other problems.
The oil level should be between the two marks
on the breather cap dipstick shown in the
following photo.
Hydraulic Oil
FULL Level
Hydraulic Oil
Level ADD
Mark
Hydraulic Oil Breather Cap/Dipstick
-Typical View
NOTE: Overfilling the hydraulic reservoir can
cause leakage of oil through the breather
cap.
Hydraulic Fluid Recommendation
Hydraulic Oil Reservoir
(Located in mid-passenger side compartment)
-Typical View
HWH® specialty hydraulic fluid or Dexron®
III automatic transmission fluid is recommended
for use in this system.
DO NOT USE brake fluid or hydraulic jack
oil, which can damage the seals and cause leaks.
Jacks and Slideout Positions
To get an accurate indication of oil level:
• Leveling Jacks must be UP
• Slideout Rooms must be IN
Checking Dipstick
The hydraulic oil level is checked with a
dipstick built into the breather/filler cap on top of
the oil reservoir, which is part of the hydraulic
pump/manifold assembly.
NOTE: Always clean away any dirt and debris
from the top of the reservoir before
removing the breather cap to avoid entry
10-6
SECTION 11 – MAINTENANCE AND STORAGE
SEALANTS – INSPECTION AND
GENERAL INFORMATION
NOTE: Proper sealant inspection includes not
just visual observation but running a
finger along sealant seams to verify
proper adhesion to the surface. Any
loosened areas must be replaced.
• Have the sealant replaced if you notice any of
the above. Your local Winnebago Industries
dealer has the correct and necessary parts and
experience to help you maintain your sealants.
See “Sealants Call-Out Sheet” provided in
your InfoCase.
• Always use the same type sealant that was
removed.
• Immediately have dealership check moldings,
windows, and exterior attachments for leak
source if you notice water inside of unit.
NOTICE
Sealants must be inspected every 6
months and replaced if necessary.
ROOF
WARNING
STAY OFF ROOF. Surface may be
slippery. Falling could result in death or
serious injury.
The roof is made of Thermo-Panel materials
like the walls and floor. It will support the weight
of an average adult for periodic maintenance or
repair of the roof or roof mounted components.
Walking or working on the roof should be left
to qualified service personnel using proper safety
equipment in a safe environment. You should
only walk or work on the roof if you are qualified
and have created a safe environment.
For your safety, it is not recommended that
you store or carry items on the roof.
Always have damage to the roof area repaired
immediately. Damaged or detached sealant
around the vents, air conditioner, body-to-roof
seams, etc., should also receive immediate
attention. Delaying these repairs may allow water
leakage and result in damage to interior ceiling
and body panels, upholstery, etc., which is not
covered by the limited warranty (see” New
Vehicle Limited Warranty” provided at the
beginning of this manual).
UNDERCARRIAGE
Buildup of mud and dirt under the body of the
vehicle can cause damaging rust or corrosion on
steel or aluminum parts and can add needless
11-1
5 - DASH / AUTO
Water is a recreational vehicle’s worst enemy
when it is allowed to enter where it is not
intended. Sealants perform a very important
function and should be inspected closely and
maintained regularly. Winnebago Industries®
utilizes many different types of sealants. Refer to
the “Sealants Call-Out Sheet” provided in your
InfoCase for further information.
Sealants, in general, do not have “set”
lifetimes. Varying environmental factors affect
the pliability and adhesiveness of sealants. You
or your dealer must:
• Inspect all sealants, a minimum of every six
months.
• Inspect the moldings, windows, clearance
lights, exterior compartment doors, and all
their attachments.
• Also, inspect weather seals around entrance
door, etc., and if necessary, have a dealer
replace them immediately.
• Check for cracks, voids, gaps, breaks,
adhesion, and any sign of physical
deterioration.
SECTION 11 –
MAINTENANCE AND STORAGE
weight to the vehicle. This, in effect, reduces the
amount of cargo you can carry and remain within
GVWR and GAWR limits.
Corrosive materials, such as those used for ice
and snow removal and dust control, can also
accumulate on the underside of a vehicle. These
materials should be removed by flushing the
undercarriage regularly with water, especially
horizontal surfaces, cavities, and other areas
where mud and other deposits may collect.
EXTERIOR AUTOMOTIVE
PAINT FINISH
•
•
The exterior finish of your motorhome is fully
or partially finished with the highest quality
automotive paint and clearcoat.
Follow these precautions to keep the finish
looking its best and preserve maximum gloss and
durability.
Parking
•
•
•
Avoid parking under trees – When this
happens you should rinse the bird droppings
and tree sap off as soon as possible. Tree sap
is a form of sugar and will dissolve after a
couple of rinses. Bird droppings can eat into a
painted surface if left unattended and need
removed as soon as possible. Lukewarm
soapy water can help speed up the cleaning
process.
Avoid parking near salt spray – When this
happens you need to rinse off the salt mineral
residue to minimize the corrosiveness of the
salt.
Avoid parking near factories with heavy
smoke or industrial fallout – Industrial
fallout can eat into your exterior finish when
dew or rain mixes with it to create nitric or
sulfuric acid that gets magnified by the
intensity of the sun. As the water evaporates,
the acid becomes more powerful and attacks
the painted surface.
Rinsing and washing the surface helps remove
the fallout and neutralize the acid. After the
11-2
initial 60-day cure stage, a coat of wax or
polish can help protect the surface from these
types of contaminates.
Do not scrape ice or snow from the painted
surface. Brush off gently with a soft-bristled
snow brush – avoid being forceful with the
brush.
If brush scratches show after the motorhome
thaws out, it may be possible to remove them
by hand waxing with a silicone-free liquid
wax.
Avoid covering painted surface. When paint
is covered (especially in outdoor conditions),
water may appear between the cover and the
motorhome due to rapid temperature
fluctuations. The water may vaporize under
certain conditions and migrate into the painted
surface, possibly resulting in blisters and/or
bubbles in the paint. These blisters/bubbles
are not covered under warranty.
Covering your motorhome is at owner’s risk.
Driving
•
•
•
•
•
Avoid driving on gravel roads.
Rinse off bugs and bird droppings with water
daily.
Antifreeze, fuel, or windshield/window
solution spilled on the painted surface should
be rinsed off immediately with water and
allowed to air dry. Wiping dry with a towel
may create fine scratches due to the solvent
nature of these types of fluids.
Fuel cannot be diluted and dissipated with
water. It must be removed with a mineral spirit
type cleaner (such as SEAFOAM Bugs-BGone, or equivalent) or a silicone-free spray
wax and microfiber cloth to remove the stain
left by fuels.
Ensure that all motorhome fluids (such as gas,
oil, grease, antifreeze, transmission fluid,
brake fluid, etc.) are completely wiped off of
painted surfaces. Failure to comply may cause
the paint to blister and/or peel.
NOTE: When driving in wintry conditions, the
road surface may be covered with heavy
salts or small rocks to improve traction.
SECTION 11 –
MAINTENANCE AND STORAGE
These types of road conditions may cause
surface damage to your motorhome. If
possible, it is best to avoid these types of
exposures. However, if you do use your
motorhome under these types of
conditions, you may want to consider,
among other things, washing both the
undercarriage and the body of your
motorhome after exposure to these types
of conditions.
Washing
•
•
•
•
Commercial vehicle wash facilities should be
strictly avoided! They will scratch your
motorhome!
Truck-style wash centers have highpressure wands that emit higher than
necessary water pressures and the
brushes are very aggressive.
Most truck wash brushes are made from
a heavy plastic for durability and are
under heavy pressure. They are designed
to clean heavy road films on semi trailers
and are often dirty. They are not
designed for custom painted
motorhome’s and they will scratch the
clearcoat finish. Many times these
scratches can penetrate the clearcoat
finish, possibly causing delamination
and/or other paint related issues that are
not covered under warranty.
Wash your motorhome with cool or lukewarm
water using a quality automotive detergent
that does not contain bleach solution. Most
auto stores offer car wash detailing soaps that
are similar and do not have bleach in the
formulation (such as Meguiars #62).
Never use a bristled brush or broom to wash
the painted surface. This will cause scratches
in the finish. Using a microfiber cloth, mitt, or
mop is strongly recommended.
Be sure your cloth or applicator is clean. A
dirty applicator can scratch your motorhome.
Washing Procedure
• Rinse area to be washed with cold water to
remove surface residue. Ensure you are not in
direct sunlight.
• With area to be washed still wet from the rinse,
use the recommended soapy mixture to clean
the area. To avoid scratching painted surfaces,
a microfiber cloth, mitt, or mop is strongly
recommended to apply soapy water.
• Rinse washed area before soap evaporates.
• Dry the rinsed area before the water
evaporates.
NOTE: Avoid aiming water flow from a hose or
spray from high-pressure washing
equipment into any appliance intake, as
damage or difficulty in operating
appliances may occur.
•
After washing the motorhome, carefully
inspect sealant around window frames, vents,
and any other joints that may have loosened or
separated. See “Sealants - Inspection and
General Information” at the beginning of this
section for details.
Bug Removal
• Rinse any loose debris off with water and
allow the remaining residues to soak and
soften. Use soap and water to wash the
residue, then rinse.
NOTE: You may wish to repeat and leave soap
on longer than normal to help with
softening hardened residue.
• For more stubborn areas, use an ammoniabased glass cleaner followed by washing with
warm soapy water, then rinse.
• Remember to use microfiber towels during
this process to help avoid scratches.
• If this does not work, as a last resort, use a bug
removal product (like SEAFOAM Bugs-BGone, or equivalent) in a shady area and
follow the directions on label.
Ensure cleaner is completely wiped off of
painted surfaces. Failure to comply may cause
the paint to blister and/or peel.
11-3
SECTION 11 –
MAINTENANCE AND STORAGE
Polishing and/or Waxing
NOTE: When your motorhome is new or has
been repainted for any reason, no polish
or wax should be applied to the finish
until after a 60-day cure cycle at
temperatures higher than 60 degrees for
60 days. Failure to observe this
precaution could void your paint
warranty.
• We recommend a silicone-free polish with an
orbital machine and terry cloth applicator.
• Liquid waxes are easier to apply and bring to
a gloss with fewer residues.
• Avoid paste waxes. They sometimes have
fillers and additives that give a very short term
result. Stay away from silicones in polishes
and soaps.
• Buffing compounds remove some of the mil
film of the clearcoat, so we recommend that
only professionals or very experienced users
apply this type of product.
Inspection
A motorhome exterior is subjected to many
physical forces and environmental conditions.
While the motorhome is parked, it is exposed to
climate and weather extremes and other
environmental conditions. While in operation, it
is subjected to various twisting and flexing forces
caused by routine cornering and turning, and by
uneven road surfaces, such as bumps, potholes,
railroad tracks, and parking lot entrances.
Inspect the exterior fiberglass shell
periodically for cracks which may represent a
threat to the integrity of the fiberglass.
Minute cracks in the surface (commonly
referred to as "spider cracks" or "hairline cracks")
caused by normal flexing of the fiberglass
exterior are normal and typically pose no threat to
the integrity of the motorhome other than
appearance.
However, if a crack has opened up and the
weave of the cloth is visible, this does represent a
threat to the integrity of the fiberglass and must
11-4
be repaired or covered as quickly as possible to
avoid penetration by moisture, especially in
freezing climates.
If the fiberglass has been damaged and
contains cracks, tears, or holes, use plastic
sheeting and duct tape, if necessary, to prevent
moisture from damaging the sidewall material or
the interior of the motorhome.
Protective Film
–If Equipped
Your motorhome may be equipped with a
protective film to defend against everyday road
hazards. This film creates a barrier against bugs,
road grime, bird droppings, and other harmful
elements.
Further Information
See the manufacturer’s information provided
in your InfoCase for complete care and
maintenance instructions.
EXTERIOR GRAPHIC CARE
The pressure-sensitive graphics on your
vehicle require very little maintenance. In order
to allow the graphics to have the longest life
possible, the following steps should be taken.
• Wash graphics with plain soap and water or
any car wash detergent. Rinse thoroughly.
• High pressure water spray may loosen or
damage graphics. Keep spray nozzle at least
1 1/2 feet from the edge of the graphics.
• Test any cleaning solution on a small section
of graphic before using.
• Never use aromatic solvents such as acetone,
M.E.K., toulene, paint thinner or lacquer
thinner on graphics. Solvents may soften the
vinyl and smear colors.
• Gasoline or other fuels spilled on graphics
should be rinsed off immediately with water.
• Do not apply paint or clearcoat over the
graphics.
• Do not apply wax over the graphics,
especially wax containing petroleum
distillates. Wax that has dried along the edge
SECTION 11 –
MAINTENANCE AND STORAGE
of a graphic can be removed with cotton
swabs after softening it with isopropyl
alcohol. Rinse area thoroughly after cleaning.
PLASTIC PARTS – CLEANING
Many parts in your vehicle, such as the dash,
exterior light lenses, and certain exterior body
panels are made of high-impact plastic materials
that can be damaged by wiping with solvents or
improper cleaning products.
Always try cleaning plastic parts with the
mildest cleaners first and work your way up to
stronger cleaning products. Use the following
cautionary lists as a guide when selecting
cleaning products to use on plastic parts.
NOTICE
Do not use citrus-based cleaners on
polycarbonate finishes. Citric compounds
will damage the high-gloss surface,
causing it to appear dull or “flat”. Always
test a cleaning product on a hidden area
to be sure it will not cause damage to the
appearance of the part.
Here is a list of mild cleaners that may be used
safely:
• Car washing soap and water
• Glass cleaners without ammonia
• Mineral oil
• Multipurpose cleaners (such as Fantastik®,
Formula 409®, etc.)
The following products, compounds, or solvents
must be wiped off immediately to avoid
damage:
• Ammonia
• Brake fluid
• Bathroom basin, tub, and tile cleaners
• Chlorine
• Ethyl alcohol
• Isopropyl (rubbing) alcohol
• Kerosene or gasoline
•
•
Naphthalene
Pine-type household cleaners
Do not use cleaners containing the following
products, compounds, or solvents. These
products will damage the finish.
• Acetic acid
• Acetone (nail polish remover)
• Aromatic solvents (lacquer thinners)
• Benzene
• Butyl alcohol
EXTERIOR LIGHTS
Most Winnebago Industries® vehicles have
polycarbonate lenses on exterior lamps, which
are very sensitive to a variety of chemical
solvents and cleaners.
Use only soap and water to clean exterior
lamp lenses, especially headlights.
• Contact with certain chemicals can cause
etching, “crazing” or cracking of the lens,
which can significantly reduce the lens clarity
and effectiveness of the lamp and may require
replacement of the complete lamp housing.
• Some popular citric acid cleaners may cause
polycarbonate lenses to become “hazy” or
“foggy”.
• Do not use a pressure washer to clean
headlights.
• Inspect and operate the lights regularly to
confirm proper operation and mounting
condition.
INTERIOR SOFT GOODS
We recommend a weekly routine of
vacuuming all fabrics and carpet throughout the
motorhome to prevent an accumulation of dirt,
which can detract from the appearance and
shorten the life of carpet and fabrics.
Fabric Upholstery
Some fabrics used in this motorhome may
contain fire retardant and lightfastness additives,
which can be damaged by use of improper
cleaning products. Some water-based household
11-5
SECTION 11 –
MAINTENANCE AND STORAGE
cleaning products are not formulated for use on
fabrics and may cause excessive shrinkage or
fading. Always test any cleaning product on a
hidden area of fabric before using on visible
areas. For best results, fabric cleaning should be
referred to a professional carpet and upholstery
cleaner.
Draperies, Curtains, and
Bedspreads
NOTE: To minimize fading of upholstery, carpets
and other interior fabrics caused by
excessive sunlight, the drapes, blinds, or
shades should be closed when the
motorhome is parked for an extended
period of time.
General Stains
These items may be woven from a variety of
fabrics. We recommend that these be
professionally dry cleaned only. A five percent
shrinkage may occur when you have these items
dry cleaned.
As with any stain or contamination, the quick
response is the best, especially when done in
conjunction with the proper cleaner for the type
of stain.
CABINETRY – CLEANING
WARNING
When cleaning upholstery and fabric, do
not use lacquer thinner, nail polish
remover, laundry soaps, or bleach. Never
use carbon tetrachloride, gasoline, or
naphthalene for any cleaning purpose.
These materials may cause damage to
the material being cleaned and most are
highly flammable, posing risk of injury due
to fire.
Leatherette
–If Equipped
Leatherette materials are easy to care for and
require no recommended maintenance other than
regular cleaning. To clean, only use:
• Mild soap and water
• For stubborn spots, use alcohol-based
solutions such as Fantastik® or Formula 409®
• To disinfect, use a 5:1 bleach/water solution
• Always rinse with clean water
• Allow to air dry
Vinyl Fabrics (including ceiling)
–If Equipped
Vinyl should be cleaned with a soft, damp
cloth, and a mild detergent only. Do not use
solvents. Solvents may damage the surface of the
vinyl.
11-6
Wooden items may be cleaned with a soft
cloth and a good quality wood finish cleaning
product.
Vinyl simulated wood panels may be cleaned
with a mild, water-based cleaner and a soft cloth.
Do not use solvents on vinyl wood panels.
NOTE: Many cabinetry and furniture items
throughout this motorhome are
constructed either partially or
completely of real hardwoods. Because
of natural variations in woodgrain
density, slight differences in stain hue
may exist between one item and another.
This is the distinctive character and
beauty of real wood.
DECORATIVE VINYL WALL
PANELING – CLEANING
Decorative Vinyl Wall Paneling may be
cleaned with mild detergent and warm water. The
soap product should contain no abrasives, and the
use of a soft cloth or sponge with the cleaning
liquid should help preserve the finish of the vinyl.
Do not use bleach, cleaning agents with
solvents or harsh chemicals, oil based spray
cleaners, or other multipurpose cleaners such as
Fantastik® or Formula 409® as they could
damage the vinyl surface.
SECTION 11 –
MAINTENANCE AND STORAGE
TABLES AND COUNTERTOPS
Work surfaces are covered with a plastic or
thermo-formed laminate that resists solvents,
stains, and abrasions. A coat of furniture wax
applied to these surfaces on the counters and
table will help preserve their beauty and make
cleaning easier. Always clean the surface before
applying wax.
SOLID SURFACE
COUNTERTOP – CORIAN®
Care and Maintenance
You can easily maintain the beauty of your
countertop with little effort, under most
circumstances, by using warm soapy water or an
ammonia-based cleaner (not window cleaner)
then rinse and wipe dry. You can also use liquid
or gel-type cleaners containing bleach. Because
the material is nonporous, stains cannot penetrate
below the surface and will nearly always
disappear using these cleaning methods.
If a stain has dried on, allow the cleaner or
soapy water time to soften the area, after which
the stain will wipe off.
If the stain is not water-base or oil-base
material, you may need to gently remove it using
a plastic scraper (disposable plastic knife for
example) followed by normal cleaning methods
described above.
You may want to scrub the entire surface
periodically. Do this lightly and evenly with a
mild abrasive powdered or liquid cleaner.
Always use a cutting board rather than
slicing foods directly on your countertop. The
underside of one of your sink covers will provide
an easily accessible cutting surface. This will
keep your countertop looking its best and
minimize care efforts. (An occasional sanding
with a medium grade (120 grit) sandpaper will
remove any cut marks accumulated on the sink
cover bottom).
To remove cuts and scratches, use a more
aggressive cleaning powder such as Comet®, a
moistened steel wool soap pad, or green scouring
pad. We recommend that you finish the entire
surface using the same cleaning material and
scrubbing method to maintain a uniform
appearance.
If you prefer a glossier look, follow up with
a good quality furniture polish or a liquid
automotive wax (non-cleaner type).
Use trivets and “hot pads” under hot
cooking pans. Do not set hot pots or pans directly
from the stove or oven onto the counter. The solid
surface material is extremely heat resistant, but
sudden contact by a very hot material with a cold
countertop surface could cause a crack that
would need to be repaired. Likewise,
concentrated high heat sources in a small area,
such as a crock pot or an electric griddle may
cause a crack. We strongly recommend using a
trivet under these. Also, do not allow candles to
burn directly on the counter surface.
Avoid paint remover or oven cleaner. The
solid surface material is also resistant to most
chemical substances but exposure to some harsh
chemicals and solvents such as these can cause
damage that would need professional repair or
replacement. If one of these materials does spill
or drip onto the counter surface, wipe it up
immediately to avoid damage.
SINK – STAINLESS STEEL
Care and Cleaning Instructions
The stainless steel sink can usually be cleaned
with water and soap or detergent using a soft
cloth or sponge.
• Rinse thoroughly with warm water and wipe
dry quickly to avoid spots and streaks.
• For stubborn stains, use a mild abrasive
cleanser like Soft Scrub®, Comet®, etc. Work
in the direction of the “grain” of the brushed
finish lines.
• Never use steel wool. Particles of steel from
the wool pad can embed into the sink surface,
then become rusty and unsightly.
11-7
SECTION 11 –
MAINTENANCE AND STORAGE
•
•
•
•
Avoid contact with full-strength bleaches,
household chemicals, and acid-based
cleaners. If this happens, rinse and wipe dry
quickly.
Salt, mustard, and mayonnaise can cause
pitting if left on the steel sink surface. If
spilled, clean and rinse immediately.
A high iron content in the water (hard water)
may result in a brown or rust-colored stained
appearance. If noticed, dry towel sink after
each use.
Do not use rubber mats in the sink bowl.
Material trapped under mats can complicate
cleaning.
NOTE: Improper use may damage this product
and void the warranty.
RANGE AND REFRIGERATOR
For care and appearance maintenance of the
range and refrigerator, refer to the appliance
manufacturer’s operation and maintenance
manuals included in your InfoCase.
VINYL FLOORING
Care and Maintenance
You can easily maintain the beauty of your
vinyl flooring with little effort, by following
these recommendations:
• Sweep or vacuum floor daily (use a vacuum
without a beater bar head.) Remove loose dirt
with a soft brush or Swiffer® type product.
• For more intense cleaning, use a non-abrasive
cleanser, such as Mr. Clean®. Rinse with clean
water.
NOTE: Floor cleaners containing waxes,
brighteners, or gloss agents are not
recommended.
• Regular cleaning with solvent-based
chemicals may adversely affect the topcoat
performance.
• Do not use undiluted bleach or leave a dilution
of bleach on the floor for longer than one hour.
11-8
•
Vinyl flooring is extremely durable and long
lasting. It is normal for the floor to show some
denting and dimpling where furniture sets due
to the soft nature of the material. The dents are
not permanent and will come out over time.
Maintenance Tips
•
Install protection (such as pads or casters) on
furniture with legs or sharp edges. This
protection should not contain bitumen, which
may cause brown stains.
NOTE: Faulty pads and casters should be
removed and replaced.
• Burning cigarettes and matches can cause
damage to the flooring.
• Use doormats (that do not contain bitumen) to
keep out most of the dirt and dust.
• Remove spills immediately with a damp
cloth, followed by rinsing with clean water.
• The use of stiletto heels is not recommended,
as they may cause permanent damage to the
flooring.
• Protect flooring from prolonged direct
sunlight exposure.
Treatment of Stains
Acids, alkali, alcoholic beverages, coffee, soft
drinks, ketchup, fruit, fruit juices, food,
vegetables, mustard, ink, and iodine:
•
Remove the stain with lukewarm water and a
cloth or sponge. If necessary, clean with a soft
nylon pad and non-abrasive mild detergent or
resilient floor cleaner.
Heel marks:
•
Clean as soon as possible with a soft nylon pad
and non-abrasive mild detergent or resilient
floor cleaner.
Asphalt, candle grease, chewing gum, fat, oil,
tar, and shoe polish:
•
Gently remove with a blunt instrument and
treat with a soft nylon pad and non-abrasive
floor cleaner.
SECTION 11 –
MAINTENANCE AND STORAGE
Lacquer and nail polish:
•
Remove as soon as possible. Do not allow to
dry. If necessary, apply nail polish thinner
(sparingly) to remove any residue.
Corrosion, paint, and grass stains:
•
Treat as soon as possible with a soft nylon pad
and non-abrasive mild detergent or resilient
floor cleaner.
Varnish, oil paint, and solvents:
•
Blot up as soon as possible. Do not rub, as this
will only spread material further across the
surface. Carefully treat with a mild cleanser.
When dry, carefully peel the stain off.
MEK may be used sparingly, if necessary.
Rinse immediately with clean water.
Pet stains:
•
Treat with lukewarm water. If stain remains
visible, clean with a soft nylon pad and nonabrasive resilient floor cleaner.
BATHROOM
Toilet
For instructions on the care of your toilet, refer
to the information in your InfoCase.
Tub and Shower Walls
The tub and shower walls in the bathroom
should be cleaned with mild soap and warm
water. Do not use an abrasive cleaner on the
shower walls and tub, as scratching and
discoloration may occur. Stubborn stains may be
removed with an automotive-type cleanser.
Lavatory Sink - Acrylic
General Cleaning
Clean often with hot water and soap. If a
cleanser is necessary, make sure the product is
recommended for use on plastics.
Avoid harsh abrasive cleaners, ammonia, or
citric-based products as discoloration may result.
Rinse all food, beverage, or cosmetic residue
from the sink as soon as possible. Some residues,
if left to sit in the sink, may require the use of
detergent or mild liquid or gel-type kitchen
surface cleaner.
If acids or medicine spill on the surface, wash
the spills immediately.
Marks or Discoloration
A color-matched automotive scratch remover
compound may be used to remove stubborn
marks or discoloration. Always follow label
directions.
NOTE: Do not use steel wool or metal scouring
pads.
DOORS AND WINDOWS
Windows may be periodically cleaned with a
good quality glass cleaner or mild soap solution
using a soft cloth.
Use care when removing ice or frost from the
windows. Always use a plastic ice scraper, never
one made of metal. Use care when removing ice
from the mirrors to protect the reflective surfaces.
Door locks and hinges should be lubricated
periodically with powdered graphite to ensure
trouble-free operation and to protect against
freeze-up.
VEHICLE STORAGE –
PREPARATION
Properly preparing your vehicle for storage
will lessen the possibility of damage to your
vehicle. Prepare the motorhome for vacancy just
as you would if you were leaving your house for
an extended period.
Clean and Prep Coach for Storage
1. Turn off the propane gas tank.
2. Turn the Electronic Thermostat switch OFF.
3. Remove all foods and items that may cause
odors from cabinets and refrigerator.
11-9
SECTION 11 –
MAINTENANCE AND STORAGE
4. Clean and defrost the refrigerator. Prop the
door open slightly to allow any odors to
dissipate. Place an open box of baking soda
inside the refrigerator to help absorb odors.
5. Fully charge the batteries. Batteries must
have at least 80% charge to survive
freezing temperatures and long period of
non-use. We recommend that you connect a
battery charger or plug in the shoreline once a
month during long-term storage periods to
maintain battery charge and to avoid
sulfating. If connecting a charger directly to
batteries, turn the House/Coach Battery
Disconnect switch off to avoid electrical
arcing when attaching and detaching charge
clamps.
NOTE: We do not recommend leaving the
shoreline plugged in continuously during
storage.
6. After charging batteries, turn the House/
Coach Battery Disconnect switch off to
disconnect the batteries and avoid parasitic*
drain.
* Parasitic battery drain is the gradual drain
by items connected directly to battery power
such as clocks, radio memory, and the
engine computer.
7. Have the vehicle chassis completely serviced
and lubricated. Be sure radiator antifreeze
protection level is sufficient for the lowest
anticipated temperatures.
8. Wash and wax the coach.
9. Inspect all seams and seals around doors,
windows, vents, and any other joints. Replace
or repair any that are damaged. Sealing
materials and compounds can be purchased
from your dealer. Badly damaged weather
seals may need to be replaced by your dealer.
10. Close all windows and roof vents. Protect all
appliance vent openings from contamination
by animals or insects (e.g. bird nest, wasp
nests, etc.)
11. Lubricate all door hinges and locks.
12. Clean the interior of the coach. Dirt and stains
are more easily removed when fresh.
11-10
If you are storing your vehicle through the
winter, or in cold climates, extra preparations
must be made to protect equipment and systems
that can be damaged by freezing temperatures.
See “Winterizing Procedures” in Section 7 Plumbing.
VEHICLE STORAGE –
REMOVAL
1. Completely air out the motorhome.
2. Have the entire LP gas system checked for
leaks.
3. Check window operation.
4. Check cabinet and door hinges. Lubricate
with penetrating oil, if necessary.
5. Close all faucets and drain valves that are
open.
6. Add a few gallons of water to the fresh water
tank and turn on the water pump to check for
leaks, especially at fittings.
7. Open all faucets in turn to release trapped air
and check to be sure faucet washers have not
hardened during storage.
8. Sanitize the water system as outlined under
Disinfecting the Fresh Water System in the
Plumbing section, then flush the waterlines
thoroughly with fresh water.
9. Check the toilet for proper operation.
10. Add water to the holding tank using the toilet
flush pedal and galley sink faucet. Check to be
sure dump valves seal tightly.
11. Check around all appliances for obstructions
and ensure that all vent openings are clear.
12. Start refrigerator and check for proper
cooling.
13. Clean wall and counter surfaces.
14. Replace batteries, if necessary, and check out
electrical system to make sure all lights and
electrical components operate.
15. Check tires for proper cold inflation pressure.
See “Vehicle Certification Label” in Section 1
- Introduction.
16. After washing accumulated winter grime
from the vehicle, it is important to carefully
inspect the seams and sealants for separation
SECTION 11 –
MAINTENANCE AND STORAGE
or cracks that may have appeared around the
window frames, vents, and any other joints.
See Sealants – Inspection and General
Information at the beginning of this section.
Resealing is quite simple and the material is
quickly and easily applied. Appropriate
compounds are available from your dealer.
See the Sealants – Recommended Application
page in the Supplement Manual provided in
your InfoCase.
Also inspect weather seals around doors, etc.,
and if necessary, have a dealer replace
immediately.
CHASSIS SERVICE AND
MAINTENANCE
Consult the appropriate sections in the chassis
manual for specific information regarding
operating safety, service recommendations, and
maintenance schedules for the chassis section of
your vehicle.
11-11
SECTION 11 –
MAINTENANCE AND STORAGE
COACH MAINTENANCE CHART
These recommendations apply for normal recreational use. Heavy duty or full-time use may require more
frequent maintenance intervals.
Every Year
As Necessary

Every 6
Months

Check propane tank condition, mounting, and fittings
Every 3
Months
Pressure Regulator - inspect and adjust if needed
Monthly

Weekly

Before Each
Use
Have propane gas system checked for leaks
Always use specified sections or manufacturer’s
guide for further information and instructions.
Propane Gas System
Electrical System
Check Battery Condition Meter


Check battery fluid level and connections

Check 12V fuses and 120V breakers

Check GFCI receptacles
Generator
Visually inspect generator and compartment


See generator manufacturer’s maintenance guide
Plumbing System
Sanitize plumbing system

Winterize plumbing system


Clean water pump strainer filter

Slideout & Leveling System

Check and adjust
Check hydraulic oil level



Check hydraulic lines (routing, leaks, etc.)

Inspect slideout room seals (bulb seals), clean as necessary
Check and inspect electric slideout lock drain line(s)

Exterior

Clean roof
Clean sidewalls



Clean windows
Flush underside of vehicle
11-12



SECTION 11 –
MAINTENANCE AND STORAGE
COACH MAINTENANCE CHART
These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent
maintenance intervals.
As Necessary
Every Year
Every 6
Months
Every 3
Months
Monthly
Weekly
Before Each
Use
Always use specified sections or manufacturer’s
guide for further information and instructions.
Safety Equipment
Check operation of the following items:
Headlights, Taillights, and Marker Lights


Turn Signals


Horn


Hazard Warning Flashers


Windshield Wipers and Washers


Fire Extinguisher - check charge indicator


Smoke Alarm - test operation *


Carbon Monoxide Alarm - test operation *


Propane Gas Leak Detector - test operation


(*replace battery if needed)
Appliances
Water Heater

See water heater manufacturer’s maintenance guide
Inspect and clean exterior vent


Refrigerator

See refrigerator manufacturer’s maintenance guide
Inspect and clean exterior vent/drip tray drain tube


Furnace

See furnace manufacturer’s maintenance guide
Inspect and clean exterior vent


Air Conditioner

See A/C manufacturer’s maintenance guide

Inspect for exterior damage
Check/replace filter


Range Top
See range manufacturer’s maintenance guide

Inspect and clean/replace range hood grease filter

11-13
SECTION 11 –
MAINTENANCE AND STORAGE
COACH MAINTENANCE CHART
These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent
maintenance intervals.
As Necessary
Every Year
Every 6
Months
Every 3
Months
Monthly
Weekly
Before Each
Use
Always use specified sections or manufacturer’s
guide for further information and instructions.
Sealants

Inspect (see “Sealants - Inspection and General
Information” at the beginning of this section for
proper inspection technique)
Replace (see “Sealant Call-out Sheet” in the supplement manual provided in your InfoCase)


Frame & Chassis
Follow chassis manufacturer’s maintenance guide
(refer to chassis manual)
Inspect hitch receiver (if towing)


Tires
Check and adjust air pressure


Check tread wear



Check front end alignment and adjust if needed
Miscellaneous
Lubricate locks, hinges, and latches
11-14


SECTION 12 – MISCELLANEOUS
NOTE: Your motorhome’s load capacity is
designated by weight, not by volume, so
you cannot necessarily use all available
space when loading your motorhome.
• Store or secure all loose items inside the
motorhome before traveling. Possible
overlooked items such as canned goods or
small appliances on the countertop, cooking
pans on the range, or free-standing furniture
items can become dangerous projectiles
during a sudden stop or evasive maneuver.
• Be aware of GVWR, GAWR, and individual
load limit on each tire or set of duals.
When loading the vehicle, distribute the cargo
load equally so that you do not exceed either the
Front or Rear Gross Axle Weight Rating
(GAWR) or the Gross Vehicle Weight Rating
(GVWR). The Gross Axle Weight Rating
(GAWR) means the weight value specified by
the chassis manufacturer as the load carrying
capacity of a single axle system as measured at
the tire-to-ground interfaces. This is the total
weight a given axle is capable of carrying. Each
axle has its own rating.
Have your vehicle weighed to determine the
proper load distribution for your vehicle. Also
distribute cargo side-to-side so the weight on
each tire or dual set does not exceed one half of
the GAWR for either axle.
For example, if the Front GAWR is 6,000 lbs.,
there should be no more than 3,000 lbs. on each
tire. (If the left side weighs 3,100 lbs. and the
right side weighs 2,700 lbs., at least 100 lbs. of
the load must be shifted from the left side to the
right side.) The GVWR is listed on the Vehicle
Certification Label. (See sample in Section 1 Introduction).
The GCWR (Gross Combination Weight
Rating) means the maximum allowable loaded
weight of this motorhome and any towed trailer
or towed vehicle.
NOTE: We recommend that you dump all
holding tanks before traveling to avoid
carrying unnecessary weight.
WARNING
The weight of the loaded vehicle
(including options, attachments,
passengers, water, fuel, luggage, and all
other cargo) must not exceed the GVWR
or GAWR of either axle.
WEIGHING YOUR LOADED
VEHICLE
To check the weight of your fully loaded
coach, locate a commercial weighing scale that is
capable of weighing large trucks.
NOTE: Sales literature may give approximate or
standard weights. Your actual coach
weight may differ based on added factory
and/or dealer options.
Loading
Load your vehicle completely as if you were
going on a long trip with everything you would
carry, including food, clothing, bedding, lawn
chairs, etc., a full fuel tank, full propane tank, and
a partial tank of fresh water, but empty holding
tanks. Remember, tongue weight must be
included in the GVWR.
Finding a Scale
In urban areas, the most common places to
find a public access scale are commercial truck
stops. In rural areas, most grain storage elevators
have scales available. Most scales charge a
nominal fee for weighing a vehicle.
Weighing
There is typically a scale operator to direct
you, but the basic routine is to take three separate
weights - front axle, whole vehicle, and rear axle.
12-1
5 - DASH / AUTO
LOADING THE VEHICLE
SECTION 12 –
MISCELLANEOUS
You will first drive only your front wheels
onto the scale pad, then drive ahead so that the
whole vehicle is on the scale, then finally pull off
until just the rear wheels are on the pad.
Front GAWR (Front Axle Only)
GVWR - Whole Vehicle (All Axles)
Corner Weighing (Side-to-Side)
The most accurate method of weighing a
motorhome is to weigh each “corner” of the
coach separately (single L/R front wheels or L/R
rear dual sets.) This method will help you
determine how to distribute your cargo to avoid
overloading, especially on tires.
To determine the weight distribution on each
tire or dual set, you will need to find a scale
capable weighing side-to-side, or all four
“corners” of the vehicle separately.
A truck scale may be used if the ground is
level with the scale surface and the scale has
clearance to drive one side of the coach onto the
scale as shown.
Drive the coach on the level area next to the
scale and straddle the scale so that only one side
of the coach will be on the scale pad.
NOTE: Wind and precipitation can also cause
weight inaccuracies.
Pull only the right front wheel onto the scale
pad as shown.
Weighing Right Front Corner
Rear GAWR (Rear Axle Only)
You will receive a weight “ticket” that states
your current Front Gross Axle Weight, Rear
Gross Axle Weight, and Gross Vehicle Weight.
You can compare these weights to the weight
ratings listed on your Vehicle Certification Label
to use as a guideline for future loading limits and
weight distribution.
The gross weight of the vehicle must not
exceed the Gross Vehicle Weight Rating
(GVWR) specified on the Vehicle Certification
Label. The front and rear axle weight also should
not exceed the corresponding Axle Weight
Rating specified on the Vehicle Certification
Label.
12-2
When the front wheel has been weighed, pull
the coach straight ahead until only the right rear
wheel/dual set is on the scale pad as shown.
Weighing Right Rear Corner
Now, turn the coach around and repeat the
process for the other side.
The load on each wheel or dual-wheel set
should not exceed one-half of the corresponding
GAWR. For example, if the GAWR for the rear
SECTION 12 –
MISCELLANEOUS
axle is 12,000 lbs., then the load on each rear dual
set (left rear duals or right rear duals) should not
exceed 6,000 lbs.
Tires must be filled to the recommended air
pressure for the highest loaded tire set on that
axle. For example, on the rear axle, if the left side
weighs more than the right, fill the left tires to the
pressure required for that weight, then fill the
right tires to the same pressure as the left ones.
If your actual weight is considerably less than
GAWR, you may be able to lower your tire
pressure. See a tire dealer for a load/pressure
chart.
NOTE: The Hitch Load from a Towed Vehicle or
carrier box must also be counted on the
Rear GAWR and subtracted from the
rear axle cargo capacity.
Be aware that hitch load can affect handling
characteristics. The more weight on the hitch, the
lighter the front end will feel at the steering
wheel.
CAR OR TRAILER TOWING
–If Equipped
Hitch Capacity*
preceding items “Loading the Vehicle” and
“Weighing Your Loaded Vehicle” for
explanation of weight ratings.
Because of individual vehicle use and loading
habits, we recommend weighing the vehicle
while fully loaded to avoid exceeding any of the
listed Gross Weight Ratings. See “Vehicle
Certification Label” in the Introduction section
for information on gross weight ratings.
Towing will affect vehicle handling,
durability, and fuel economy. Exceeding any of
the listed Gross Weight Ratings will result in
unacceptable overall vehicle performance.
Maximum safety and satisfaction when towing
depends on proper use of correct equipment.
When towing a vehicle behind your
motorhome, the tow bar should be level or
pointing slightly upward towards the tow vehicle.
When coupling the vehicle tow bar to the
Factory Receiver Hitch using a “drop receiver”
or a conventional “ball mount” (commonly
referred to as a “stinger” or a “draw bar”), do not
exceed a 4” drop, nor one that the centerline of
the hitch pin to the centerline of the ball exceeds
8”. See the following Hitch Assembly
illustration.
7,500 lbs. max.
Tongue Weight*
Models 22M, 22R, 25B, 26A, 31K:
500 lbs. max.
Models 31D, 31G:
350 lbs. max.
The factory installed towing hitch on this
coach is capable of pulling 7,500 lbs. load (max.),
however, the vertical (tongue) weight may vary
according to chassis and model combinations
(*see label on hitch). Towing capacity may be
less than hitch rating.
When towing a trailer or vehicle, do not
exceed either the GVWR, the rear axle GAWR,
or the chassis GCWR by the combined loaded
weight of the coach and the towed vehicle. See
Hitch Assembly
If a towing “brake system” is required, we
recommend that a “modulated” towed vehicle
braking device be installed. This means that
when the motorhome brakes are applied, whether
hard or soft, a mirror effect occurs in the braking
12-3
SECTION 12 –
MISCELLANEOUS
of the towed vehicle. In other words, the more
force applied to the motorhome brakes, the more
force will be applied to the rear vehicle’s braking
system.
We do not recommend the usage of a “surgestyle” braking device. The usage of a surge brake
(especially when coupled with a hitch ball
located outside our recommended limits) places
excessive stress on the hitch. This abuse of the
ball mount and the hitch may cause premature
hitch assembly failure.
Finally, do not forget to consider the actual
tongue weight. This should not exceed the stated
hitch vertical load for your vehicle. This weight
is typically defined as the tongue weight of a
towed vehicle hitch, boat trailer tongue weight,
or a receiver-mounted carrier rack.
Check state regulations on trailer weight and
trailer brake requirements to be sure you select
the right equipment before towing.
Before descending a steep or long grade when
towing a trailer, reduce speed and shift into a
lower gear to control vehicle speed. Avoid
prolonged or frequent application of brakes,
which could cause overheating and brake failure.
TRAILER WIRING
CONNECTOR
Your coach is pre-wired for trailer or car
towing lights with a 7-pin socket.
The following diagram shows proper
connection of trailer or tow vehicle wiring to the
coach light system. The “pigtail” assembly with
the (car/trailer end) connector plug should be
wired by a qualified technician.
The trailer brake controller connector is
located to the left of the steering column.
TOWING GUIDELINES
WARNING
For safe towing and vehicle handling,
maintain proper trailer weight distribution.
The total weight of the motorhome and
the vehicle towed must not exceed the
Gross Combined Vehicle Weight rating.
See the Body and Chassis Specification
chart in the Introduction section.
Gross Vehicle Weight Rating
(GVWR)
This is the maximum allowable weight of the
fully loaded vehicle. Included are fuel, water, LP,
passengers, cargo, tools, and optional equipment
installed by the motorhome manufacturer, dealer,
or owner. This value is found on the VIN label,
typically placed near the driver position.
Gross Axle Weight Rating (GAWR)
NOTICE
Exceeding any of the recommended
gross vehicle weight ratings may result in
vehicle damage. Do not install a frame
equalizing-type hitch on your vehicle.
12-4
This is the total weight a given axle is capable
of carrying, measured at the ground. Each axle
has its own rating. These values are also found on
the Vehicle Certification Label: front and rear.
Gross Combination Weight Rating
(GCWR)
This is the maximum allowable weight of the
motorhome and loaded trailer, including the
items noted in GVWR above. For purposes of
SECTION 12 –
MISCELLANEOUS
this definition, the “trailer” can be a trailer, a
vehicle towed on a dolly, or a vehicle towed by
means of a tow bar. GCWR is typically specified
based on durability and performance of the tow
vehicle drive train: engine and cooling systems,
transmission, drive line, drive axle, and others.
The tow vehicle brakes may be rated for
operation at GVWR, not GCWR.
NOTE: State or provincial laws/regulations may
require the “trailer” to be equipped with
brakes that are activated when the
motorhome brakes are applied. The user
is responsible to know and understand
the laws of the state or province being
traveled. The Department of
Transportation in a given state or
province should be able to provide
specific information.
mid-size SUV; a Class 4 hitch allows “dingy”
towing a large SUV or pickup. (Hitch ratings are
independent of towing vehicle ratings.)
NOTE: Some Winnebago Industries® models
equipped with a Class 3 hitch may have a
label limiting vertical tongue load to 350
lbs. Some Winnebago Industries models
equipped with a Class IV hitch have a
label limiting vertical tongue load to 500
lbs. On a 228" wheelbase, a 500-lb. load
on a hitch 11' from the rear axle will
apply about 800 lbs. at the axle.
The user must verify that the hitch equipment
being used is adequate for the application.
Hitch Ratings
SAE Standard J684 defines:
• Class 1 trailers as “GVWR not to exceed
2,000 lbs”.
• Class 2 trailers as “GVWR over 2,000 lbs. and
not to exceed 3,500 lbs. GVWR”.
• Class 3 trailers as “GVWR over 3,500 lbs. and
not to exceed 5,000 lbs. GVWR”.
• Class 4 trailers as “GVWR over 5,000 lbs. and
not to exceed 10,000 lbs. GVWR”.
Hitches are to be permanently marked with
“Maximum trailer GVWR to be drawn” and
“Maximum vertical tongue weight to be
imposed.” The SAE standard does not specify a
vertical load rating.
Traditionally, hitches are labeled 3,500/350 as
Class 2, 5,000/500 as Class 3, and 10,000/1,000
as Class 4. The vertical tongue load value of 10
percent of drawn rating comes from the
collective experience that 10 percent is the
minimum value that provides stable towing of a
trailer.
Ford’s towing guide suggests 10 to 15 percent
for trailers over 2,000 lbs. Within GCWR, a
Class 3 hitch allows “dingy” towing a large car or
12-5
SECTION 12 –
MISCELLANEOUS
STABILIZING JACKS
–If Equipped
Your coach may be equipped with stabilizing
jacks to help stabilize the coach from movement
while parked. Do not attempt to lift your coach
with the stabilizing jacks.
• To extend the jacks, the ignition key must be
in the off position.
• The jacks may be retracted with the ignition
key in the on or off position.
Passenger Side
Stabilizing Jack
Driver Side
Stabilizing Jack
WARNING
• Keep all people clear of the coach
while operating the stabilizing system.
• When extending the rear stabilizers,
do not attempt to lift the coach.
• Do not use the stabilizers on icy or slick
surfaces on which the foot pads may
slip.
• Do not use stabilizing jacks to support
the vehicle for service or tire changing.
Stabilizer Down Light
The “Stabilizer Down” reminder is intended
to warn you to retract your stabilizing jacks
before moving the vehicle. The light will come
on briefly and a chime will sound when the
ignition key is turned to the On or Run positions
if the stabilizing jacks are down.
Stabilizing Jack Switches
•Model 22M - Located inside rear driver side
compartment.
•Model 22R - Located inside backwall
compartment.
•Models 26A and 25B - Located inside rear
passenger side compartment.
“Stabilizer Down” Light
(Located on dash)
-Typical View
Further Information
Stabilizing Jacks
Shown in Down Position
-Typical View
12-6
See the manufacturer’s user guide provided in
your InfoCase for complete operating
instructions, safety precautions, and
troubleshooting tips.
SECTION 12 –
MISCELLANEOUS
AWNING – MANUAL
–If Equipped
Further Information
For complete operating instructions, refer to
the manufacturer’s information provided in your
InfoCase.
AWNING – POWER
–If Equipped
The Power Awning and Awning Light
switches are located near the entrance door.
Awning Light
Switch
Power
Awning
Switch
•Press to
Extend
(OUT).
•Press to
Retract
(IN).
The Ignition Lockout System will disable the
extend function while the vehicle ignition key is
in the On position. With this feature, the Awning
will only extend when the vehicle ignition key is
in the Off position. The Awning can retract
anytime regardless of the ignition key position.
Further Information
For complete operating instructions, features,
safety precautions, and maintenance care, refer to
the Power Awning manufacturer’s information
provided in your InfoCase.
STORAGE COMPARTMENT
DOORS
The high-density gaskets used on the exterior
storage compartments are designed to provide a
more positive seal against dust and weather.
To ensure that exterior storage compartment
doors have latched properly, press firmly on the
bottom edges of the doors with the palms of your
hands while twisting latches.
TOOL AND LADDER STORAGE
Power Awning and Awning Light Switch
(Located near entrance door.)
-Typical View
C AU T I ON
Pinch Hazard. Ensure there are no
people who could be harmed or objects
that can be damaged. Failure to heed this
warning could result in severe injury and/
or property damage.
Operating the Awning
•
Ignition Lockout System
Press and Hold the Power Awning switch IN
or OUT to extend or retract the awning as
desired.
–If Equipped
The roof ladder extension and various tools
supplied with your coach are stored in one or
more of the exterior storage compartments.
NOTE: Actual features and locations may vary
depending on model, available
equipment, and storage compartment
configuration.
ROOF LADDER
–If Equipped
WARNING
STAY OFF ROOF. Surface may be
slippery. Falling could result in death or
serious injury.
12-7
SECTION 12 –
MISCELLANEOUS
The ladder on your vehicle is provided for
limited access to the roof.
Walking or working on the roof should be left
to qualified service personnel using proper safety
equipment in a safe environment. You should
only walk or work on the roof if you are qualified
and have created a safe environment.
For your safety, it is not recommended that
you store or carry items on the roof.
Before Using the Ladder
•
•
•
Inspect the ladder to make sure it is not
damaged. Never use a damaged ladder.
Keep the rungs of the ladder clean and dry
while in use. Never use the ladder when it is
raining, snowing, or icy. The rungs can
become slippery. Do not step onto the rungs if
the rungs are wet, or if your shoes are wet or
carry mud or debris that could result in a loss
of footing.
Never ignore warning labels or weight limits
defined on your ladder. The following
warning label is located on or near the ladder:
POWER ROOF VENTILATOR
–If Equipped
The Power Roof Ventilator features a rain
cover, electric lift, and thermostat operation with
intake and exhaust airflow.
The vent is controlled by a switch on the wall,
remote (if equipped), or keypad controls on the
fan.
NOTE: In event of power failure, the ventilator
dome may be opened or closed manually
using the Dome Crank knob.
Dome Crank
Arrow
WARNING
Do not exceed 225-lb. maximum weight capacity.
Misuse of ladder could result in death or serious injury.
See Operators Manual before using ladder.
•
•
•
•
•
•
•
Maximum Capacity: 225 lbs.
Do not overload. Ladder is intended for one
person.
Make sure you are physically capable to
safely use the ladder. Strength, flexibility, and
stability are required.
Be aware that the vehicle may sway as you
climb the ladder. Do not use the ladder in high
winds.
As you climb the ladder, grasp the side rails
firmly and always use both hands. Keep your
body centered between the side rails. Do not
over-reach.
Never allow children on the ladder.
Do not transport items anchored to the
ladder. You could damage the ladder.
12-8
Auto
On/Off
Power Roof Ventilator
•
ON/OFF – Press to turn the fan on or off. The
vent lid will open automatically when the fan
is turned on and close when the fan is turned
off.
NOTE: In Auto Mode the fan direction is
automatically positioned to Exhaust, but
may be overridden and changed to
Intake by depressing the button.
• AUTO – Press to enter Auto Mode. You will
hear three (3) quick beeps to confirm the fan
is in Auto Mode. To exit Auto Mode, press the
On/Off button.
SECTION 12 –
MISCELLANEOUS
•
ARROW – In Auto Mode press the +/- arrow
buttons to adjust thermostat temperature up or
down. Press the +/- arrow buttons at the same
time to open or close the vent lid.
NOTE: For best results, close all other roof
vents, windows, and doors, then open
one (1) window the farthest distance
from the roof ventilator. The fan speed
selector allows you to control the amount
of circulation you need at any time.
Further Information
-Typical View
See the power ventilator manufacturer’s
operating instructions supplied in your InfoCase
for further instructions, care, and cleaning
information.
WINDOWS
Horizontal Slider Windows
Swing the latch handle straight out or up
(depending on the style of window). Grasp the
sliding window edge frame and slide the window
to the side. Ensure the latch is open before trying
to slide the window closed.
-Typical View
EFFECTS OF PROLONGED
OCCUPANCY
Your motorhome was designed primarily for
recreational use and short-term occupancy. If you
expect to occupy your coach for an extended
period, be prepared to deal with condensation and
humid conditions that may be encountered.
Humidity and Condensation
-Typical View
Vertical Slider Windows
Vertical windows have spring-loaded catches
on both sides of the window that pop out to hold
the window in its fully raised position. Press both
catches inward while opening and closing the
window.
Moisture condensing on the inside of
windows is a visible indication that there is too
much humidity inside the coach. Excessive
moisture can cause water stains or mildew, which
can damage interior items such as upholstery and
cabinets.
When you recognize the signs of excessive
moisture and condensation in your coach, you
should take immediate action to minimize their
effects.
12-9
SECTION 12 –
MISCELLANEOUS
You can help reduce excessive moisture
inside the motorhome by taking the following
steps:
Ventilate with outside air
Partially open one or more windows and a
roof vent to circulate outside air through the
coach. In cold weather, this ventilation may
increase use of the furnace, but it will greatly
reduce the condensation inside the coach.
Minimize moisture released inside the
coach
Run the range hood fan while cooking and
open a bath vent while bathing or showering to
carry water vapor out of the coach. Avoid making
steam from boiling water excessively or letting
hot water run. Avoid bringing extra moisture into
the coach by way of soaked clothing or snow on
shoes. Do not hang-dry wet overcoats or clothing
inside the coach.
12-10
About this Manual .................................................................................................................................. 1-1
Air Conditioner Filter ........................................................................................................................... 4-14
Air Conditioner/Heater – Automotive (Dash) ........................................................................................ 3-5
Air Springs – Rear Helper ...................................................................................................................... 3-8
Audio/Video System Basic Operation .................................................................................................... 8-1
Awning – Manual ................................................................................................................................. 12-7
Awning – Power ................................................................................................................................... 12-7
Bathroom .............................................................................................................................................. 11-9
Battery Access ........................................................................................................................................ 6-9
Battery Boost Switch .............................................................................................................................. 3-5
Battery Care ............................................................................................................................................ 6-9
Before Driving ........................................................................................................................................ 1-2
Bunk Beds/Wardrobe Conversion .......................................................................................................... 9-9
Cab Seat Lounge Cushion ....................................................................................................................... 9-1
Cabinetry – Cleaning ............................................................................................................................ 11-6
Car or Trailer Towing ........................................................................................................................... 12-3
Carbon Monoxide Alarm ........................................................................................................................ 2-4
Carbon Monoxide Warning .................................................................................................................... 2-5
Chassis Service and Maintenance ....................................................................................................... 11-11
Checking Hydraulic Oil Level .............................................................................................................. 10-6
Child Restraints ....................................................................................................................................... 3-2
Circuit Breakers – House 120-Volt AC .................................................................................................. 6-5
Circuit Breakers and Fuses – House 12-Volt DC ................................................................................. 6-11
Coach Maintenance Chart ................................................................................................................... 11-12
Decorative Vinyl Wall Paneling – Cleaning ......................................................................................... 11-6
Dinette Flip-Up Footrests ....................................................................................................................... 9-8
Dinette/Bed Conversion – Dream Dinette™ .......................................................................................... 9-4
Dinette/Bed Conversion .......................................................................................................................... 9-5
Disinfecting Your Fresh Water System .................................................................................................. 7-4
Doors and Windows .............................................................................................................................. 11-9
Drainage System (P-Traps) ..................................................................................................................... 7-6
Driving Safety ......................................................................................................................................... 2-1
Ducted Roof Air Conditioning System ................................................................................................. 4-14
DVD Player ............................................................................................................................................. 8-1
DVD Player ............................................................................................................................................. 8-2
DVD Player ............................................................................................................................................. 8-3
Effects of Prolonged Occupancy .......................................................................................................... 12-9
Electrical ................................................................................................................................................. 2-6
Electrical Cautions .................................................................................................................................. 6-1
Electrical Generator – 120-Volt .............................................................................................................. 6-6
Electrical Outlets – House 120-Volt AC ................................................................................................ 6-6
Electrical System – House 120-Volt AC ................................................................................................ 6-1
5 - DASH / AUTO
INDEX
Index
Electrical System – House 12-Volt DC .................................................................................................. 6-8
Emergency Exits ..................................................................................................................................... 2-7
Engine Access – Interior ......................................................................................................................... 3-7
Engine Cooling System .......................................................................................................................... 3-7
Engine Overheat .................................................................................................................................... 2-12
Exterior Automotive Paint Finish ......................................................................................................... 11-2
Exterior Cable TV Connection ............................................................................................................... 8-5
Exterior Entertainment Center (Adjustable) ........................................................................................... 8-5
Exterior Graphic Care ........................................................................................................................... 11-4
Exterior Lights ...................................................................................................................................... 11-5
Exterior Shower/Wash Station ................................................................................................................ 7-5
Fire Extinguisher ..................................................................................................................................... 2-6
Fold-Down Dinette Seat ......................................................................................................................... 3-1
Formaldehyde Information ..................................................................................................................... 2-8
Fresh Water System ................................................................................................................................ 7-1
Front Axle Tire Alignment ..................................................................................................................... 1-2
Front Overhead Bunk .............................................................................................................................. 9-1
Fuel and Propane Gas ............................................................................................................................. 2-2
Furnace – Propane Gas ......................................................................................................................... 4-13
General Slideout Care ........................................................................................................................... 10-4
General Warnings ................................................................................................................................... 2-1
Ground Fault Circuit Interrupter ............................................................................................................. 6-6
Hazard Warning Flashers ........................................................................................................................ 3-3
Holding Tank Heater ............................................................................................................................... 7-8
House/Coach Battery Disconnect Switch ............................................................................................... 6-8
Ice Maker Water Filter ............................................................................................................................ 7-4
Interior Soft Goods ............................................................................................................................... 11-5
Inverter Unit – 1000W ............................................................................................................................ 6-3
Jump Starting ........................................................................................................................................ 2-11
Keys ........................................................................................................................................................ 3-3
Leveling System ................................................................................................................................... 10-4
Lights ...................................................................................................................................................... 3-9
Loading ................................................................................................................................................... 2-6
Loading the Vehicle .............................................................................................................................. 12-1
Maintenance ............................................................................................................................................ 2-7
Microwave Oven ..................................................................................................................................... 4-9
Microwave/Convection Oven ................................................................................................................. 4-9
Mirrors – Manual Sideview Exterior ...................................................................................................... 3-4
Mirrors – Power Sideview Exterior ........................................................................................................ 3-4
Mold, Moisture, and Your Motorhome .................................................................................................. 2-9
Occupant and Cargo Carrying Capacity Label ....................................................................................... 1-3
Owner and Vehicle Information ............................................................................................................. 1-6
Plastic Parts – Cleaning ........................................................................................................................ 11-5
Pleated Blinds ......................................................................................................................................... 9-9
Power Center ........................................................................................................................................... 6-4
Index
Power Cord – External ............................................................................................................................ 6-1
Power Roof Ventilator .......................................................................................................................... 12-8
Pre-Delivery Inspection .......................................................................................................................... 1-2
Pressure-Temperature Relief Valve ...................................................................................................... 4-12
Propane Accessory Connection .............................................................................................................. 5-2
Propane Gas Leak Detector .................................................................................................................... 2-3
Propane Gas Leaks .................................................................................................................................. 2-3
Propane Gas Pressure Regulator ............................................................................................................. 5-5
Propane Gas Supply ................................................................................................................................ 5-1
Propane Gas Warnings and Precautions ................................................................................................. 5-4
Propane Vaporization in Cold Weather .................................................................................................. 5-6
Radio In-Dash/Rearview Monitor System .............................................................................................. 3-6
Range and Oven with Glass Range Cover .............................................................................................. 4-7
Range and Refrigerator ......................................................................................................................... 11-8
Range Hood ............................................................................................................................................ 4-9
Refrigerator ............................................................................................................................................. 4-1
Refrigerator ............................................................................................................................................. 4-2
Refrigerator ............................................................................................................................................. 4-3
Refrigerator ............................................................................................................................................. 4-5
Refrigerator (Exterior) ............................................................................................................................ 4-7
Refrigerator Service Access Compartment ............................................................................................. 4-6
Reporting Safety Defects ........................................................................................................................ 1-2
Roadside Emergency ............................................................................................................................ 2-10
Roller Shades (Manual) – Solar/Blackout ............................................................................................ 9-10
Roof ...................................................................................................................................................... 11-1
Roof and Ladders .................................................................................................................................. 2-10
Roof Ladder .......................................................................................................................................... 12-7
Safe Use of the Propane Gas System ...................................................................................................... 5-3
Safety Messages Used in this Manual .................................................................................................... 1-1
Sealants – Inspection and General Information .................................................................................... 11-1
Seat Belts ................................................................................................................................................ 3-1
Seats – Driver/Co-Pilot ........................................................................................................................... 3-1
Service and Assistance ............................................................................................................................ 1-2
Shower Hose Vacuum Breaker ............................................................................................................... 7-5
Sink – Stainless Steel ............................................................................................................................ 11-7
Sleeping Facilities ................................................................................................................................... 9-1
Slideout Emergency Retraction (Power Gear®) In Wall Slideout ....................................................... 10-3
Slideout Room – Extreme Weather Precaution .................................................................................... 10-3
Slideout Room Lock System ................................................................................................................ 10-1
Slideout Room Operation – Electric ..................................................................................................... 10-1
Slideout Room Troubleshooting (Power Gear®) In Wall Slideout ...................................................... 10-3
Slideout Rooms ....................................................................................................................................... 2-8
Smoke Alarm .......................................................................................................................................... 2-5
Sofa/Bed Conversion .............................................................................................................................. 9-3
Sofa/Sleeper ............................................................................................................................................ 9-3
Index
Solid Surface Countertop – Corian® .................................................................................................... 11-7
Specifications and Capacities ................................................................................................................. 1-5
Stabilizing Jacks ................................................................................................................................... 12-6
Storage Compartment Doors ................................................................................................................ 12-7
Suspension Alignment and Tire Balance ................................................................................................ 3-8
Systems Monitor Panel ........................................................................................................................... 4-9
Tables and Countertops ........................................................................................................................ 11-7
Tires ........................................................................................................................................................ 3-7
Toilet ....................................................................................................................................................... 7-6
Tool and Ladder Storage ....................................................................................................................... 12-7
Towing Guidelines ................................................................................................................................ 12-4
Trailer Wiring Connector ...................................................................................................................... 12-4
TV – (Swivel) ......................................................................................................................................... 8-1
TV Antenna – Digital ............................................................................................................................. 8-4
TV Antenna ............................................................................................................................................. 8-5
TV Signal Amplifier ............................................................................................................................... 8-5
Undercarriage ........................................................................................................................................ 11-1
U-Shaped Dinette/Bed Conversion ......................................................................................................... 9-6
U-Shaped Dinette/Bed Conversion ......................................................................................................... 9-7
U-Shaped Dinette/Bed Conversion ......................................................................................................... 9-8
Vehicle Certification Label ..................................................................................................................... 1-4
Vehicle Storage – Preparation .............................................................................................................. 11-9
Vehicle Storage – Removal ................................................................................................................ 11-10
Vinyl Flooring ....................................................................................................................................... 11-8
Waste Water System ............................................................................................................................... 7-6
Water Heater – Gas ............................................................................................................................... 4-10
Water Heater – Gas/ Electric ................................................................................................................ 4-11
Water Heater Bypass and Antifreeze Siphon Valves ........................................................................... 7-10
Water Pump ............................................................................................................................................ 7-2
Water System Drain Valve Locations ................................................................................................... 7-14
Waterline & Tank Drain Valves ............................................................................................................. 7-9
Weighing Your Loaded Vehicle ........................................................................................................... 12-1
Windows ............................................................................................................................................... 12-9
Winterizing Optional Appliances ......................................................................................................... 7-12
Winterizing Procedure .......................................................................................................................... 7-10
Wood Furniture and Cabinetry ............................................................................................................. 9-11
Download PDF
Similar pages
Blizzard H400WH User Manual
E- 1D3 Series
E- 1D3 Series
E- 1D3 Series
D - 1DG Series