PERSONAL SIZE FIREPLACE
OWNER’S MANUAL
Model No. FEJ-16A-1
SKU No. 1247304
PLEASE SAVE THESE INSTRUCTIONS
WARNING:
READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.
Thank you for choosing our Electric Fireplace. This owner’s manual will provide you with
valuable information necessary for the proper care and maintenance of your new
product. Please take a few moments to thoroughly read the instructions and familiarize
yourself with all the operational aspects of your new heater.
PLEASE SAVE THESE INSTRUCTIONS
2
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS,
SAFETY WARNINGS, BEFORE USING THE HEATER
WARNING!
! POTENTIAL FOR ELECTRICAL HAZARD IF NOT
ADHERED TO!
When using electrical appliances, basic precautions should always be followed to
reduce the risk of fire, electric shock, and injury to persons, including the following:
1. Read all instructions before using this heater.CAUTION: Risk of Electric Shock.
DO NOT open or try to repair the heater yourself.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. If provided, use handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding, papers, clothes, and curtains at
least 3 feet (0.9 m) from the front of the heater and keep them away from the
sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or the
disabled, or when the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. DO NOT operate any heater with a damaged cord or after the heater
malfunctions, has been dropped or damaged in any manner. Return heater to
authorized service facility for examination, electrical or mechanical adjustment,
or repair.
6. This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. NEVER locate heater where it may fall into a bathtub or other
water container. To protect against electrical hazards, DO NOT immerse in
water or other liquids.
7. DO NOT touch the control panel or plug with a wet hand. DO NOT run cord
under carpeting. DO NOT cover cord with throw rugs, runners, or similar
coverings. Do not route cord under furniture or appliances. Arrange cord away
from traffic area and where it will not be tripped over.
8. DO NOT insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.
9. To prevent a possible fire, DO NOT block the air intakes or exhaust in any
3
manner. DO NOT use on soft surfaces, like a bed, where openings may become
blocked.
10. A heater has hot and arcing or sparking parts inside. DO NOT use in areas
where gasoline, paint, explosive and/or flammable liquids are used or stored.
Keep unit away from heated surfaces and open flames.
11. Always plug heaters directly into a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap (outlet/power strip).
12. To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical
outlet.
13. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull
firmly on the plug, DO NOT unplug by pulling on the cord.
14. Always unplug the unit before moving or cleaning, or whenever the heater is not
in use.
15. Use only for intended household use as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric shock, or injury
to persons. The use of attachments not recommended or sold by unauthorized
dealers may cause hazards.
16. Always use on a dry, level surface. Use on floor only.
17. DO NOT use outdoors.
18. WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit
with any solid-state speed control device.
19. DO NOT attempt to repair or adjust any electrical or mechanical functions on this
unit. Doing so will void your warranty. The inside of the unit contains no user
serviceable parts. Qualified personnel should perform all servicing only.
SAVE THESE INSTRUCTIONS
4
SPECIFICATIONS
Voltage Rating
120 V (60Hz)
Power
Consumption
1500W
Unit Size
14.3 in. (W) x 7.9in. (D) x 9.8in. (H)
Unit Weight
10.8 lbs
SAFETY FEATURES
Overheat Safety Feature
This heater is equipped with an overheat safety feature. When the heaters internal
components reach a certain temperature that could cause overheat and possible fire,
the heater will automatically shut off.
WARNING: It is normal for the power cord to feel warm to the touch; however, a loose
fit between the outlet and the plug may cause overheating of the plug. If this occurs, try
inserting the plug into a different outlet. Contact a qualified electrician to inspect the
original outlet for damage.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is
wider than the other). To reduce the risk of electric shock, t
his plug is intended to fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If i
t still does not fit, contact a qualified electrician to install the
proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT
THIS SAFETY FEATURE IN ANY WAY.
5
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts
with package contents list and hardware contents above. If any part is missing or
damaged, do not attempt to assemble the product. Contact customer service for
replacement parts.
PRODUCT DIAGRAM
Heater / Blower
Assembly
Ember Bed
(#1)
(#2)
(#3)
1. The main power switch is located on the Rear cover and switch with flame effect
2. Heat switch – One switch for low heat setting (750 Watts)
3. Heat Switch - Two switches for high heat setting (1500 Watts)
AUTOMATIC CUT-OFF
A cut-off switch is fitted to the heating element to prevent damage due to overheating. If
it cuts-off due to an obstruction in the airflow, the heater must be allowed to cool for 10
minutes and the obstruction must be removed before restarting.
OPERATING YOUR HEATER
Once the stove has been properly assembled and connected to an electrical
outlet, it is ready to operate:
1. Main Power:
The main power switch (#1) is located on the Rear cover.
Press the switch with flame
effect.
2. 750W:
For low heat function - Press 750W switch (#2) while the main power switch (#1) is
opened.
3. 1500W: (Both 750W Switches)
6
For high heat function - Press both two 750W switches (#2) (#3) while the main power
switch (#1) is opened.
MAINTENANCE
1. Glass Information
* Under no circumstances should this product be operated with missing or broken glass.
* Do not strike or slam the glass.
* Do not use abrasive cleaners to clean the glass.
* Replacement glass is available from the manufacturer and replacement should be
carried out
By a qualified service person.
2. Cleaning
*To clean the unit, first turn off controls on unit and unplug unit from power source.
*To clean the glass door: remove dust with clean dry cloth or to remove finger prints and
Other marks clean glass with clean damp cloth. Do not use abrasive cleaners or spray
Liquids on glass door surfaces.
*Metal and metal painted parts should be cleaned with clean damp cloth only. Do not
Use abrasive cleaners or spray liquids on this surface.
TROUBLE SHOOTING
If the heater will not operate, please check the following before seeking repair of service:
1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the outlet is working.
3. Insure the main power switch is switched to “on”
4. If the power button is turned on but the heater is not operating, then the safety
Overheat function may have been triggered. Try pressing the power button. If the
Heater does not turn on, clear any obstructions from front and rear of heater that may
Have caused internal overheating. Allow the heater to cool approximately 15 minutes.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt buildup, use the original packaging to repack the unit.
7