Model XL-3 Security System Owner`s Manual

_ _-.
_
:
‘,
XL-3
-
i
- - -
SECURITY SYSTEM
OWNERS MANUAL
FIRE BURGLARY INSTRUMENTS, INC.
N9115 5/92 01992, FBX
INTRODUCTION
Congratulations on your decision to protect your home or business with the
XL-3 series security system. You have chosen a reliable, state of the art securii
system that is remarkably easy to operate. Your system has been professionally
installed by your local security company who can explain the specifics of your
system within your location.
j
i
The keypad is the arming station for your security system. These are available
keypads for your system:
XL4612RM Metal plate keypad containing indicator lights for each of the 12
zones (areas of protection). This keypad can be flush mounted into your wall or
surface mounted in a back box.
XL 461294 This is a surface mount keypad with 12 LEDs for monitorfng ZQ”‘\
status.
‘1 ,/
I
I
7015 Keypad with a plastic case and with indicator lights to show the status of
each of the zones. The zone indicator lights are located behind the plastic
sliding door of the keypad (left hand side). NOTE: This keypad displays zone
status indication lights for 16 zones.
I
7005 Keypad with a plastic case and a two line LCD (liquid crystal display) with ’
a two line readout.
I
Please identify the keypad(s) present on your system from the diagrams shown
in the sections that follow.
I
I
The XL-3 is the Residential version of’ the which has been Listed by
Underwriters Laboratories for household Fire and Burglary applications.
I
I
I
The model XL-3B is the Commercial Burglary configuration of the control panel
and has been Listed by Underwriters Laboratories for Commercial Burglary
applications.
‘XL-3 USER’S MANUAL Page 1
-
1
TABLE OF CONTENTS
1. KEYPAD LAYOUT XL4612RM and XL4612SM
2. KEYPAD LAYOUT 7015 and 7005
3. KEYPAD CONVENTIONS
4. ARMING THE SYSTEM
5. DISARMING
6. STAY
7. INSTANT
8. INSTANT-STAY
9. BYPASS
10. UNBYPASS
11. USER DEFINITION
USER DELETION
’ KEYPAD AUXILIARV CONDITIONS
8
DURESS
15: ARM-ONLY (MAID) CODE
16. DOOR STRIKE USER CODE
17. KEY PAD TAMPER
18. QUICK ARMING
19. QUICK FORCED ARMING
20. SET TIME OF DAY
21. ZONE DIRECTORY
22. SET AUTO-ARM TIME
23. CHIME MODE
24. READ CLOCK TIME
25. READ AUTO-SET TIME
26. DOOR STRIKE COMMAND
27. INSTALLATION LAYOUT
28. SYSTEM TESTING
FCC STATEMENT
LIMITATIONS STATEMENT
OWNERS INFORMATION
NOTES
SUMMARY
WARRANTY
XL-3 USER’S MANUAL Page 2
3
4
z
7
8
8
9
9
10
10
11
11
11
11
12
12
12
12
12
12
13
13
13
13
13
14
15
16
17
19
20
22
23
1. KEYPAD LAYOUT XL4612RM and XL4612SM
I
c
XL4612RM KEYPAD
XL461 2SM KEVPAD
,Jr)
W!+
L-1
1) ZONE STATUS INDICATORS - displays the current zone status as follows:
ALARM
BYPASS
TROUBLE
NOT READY
READY
Fast blinking.
Slow blinking low intensity.
Slow pulse
Solid ON
OFF
2) ARM/DISARM INDICATOR -indicates system armed or disarmed.
If the system is armed (ARMED indicator ON) then the RDY light will indicate
the arming mode (see item 4 below).
3) AC/LOW BATTERY - shows whether the system is running on AC (ON) or
backup battery (OFF). If the light is blinking slowly then the battery is low, if it is
blinking rapidly then there is a telephone line failure detected.
4) READY Indicates whether the system is ready for arming (ON = Ready, OFF
= Not Ready).
In addition, the RDY light shows the arming status if the ARMED LED is ON as
follows:
OFF = Armed in Away mode
Slow Blink = Armed in STAY mode (interior zones bypassed)
,/7
Fast Blink = Armed in INSTANT mode (exit/entry delay eliminated)
!
Fast & Slow Blink = Armed in STAY-INSTANT mode
5) NUMERICAL KEYPAD operates in a similar manner to a calculator or
telephone with the digits 0 - 9 and # clearly marked.
l
XL-3 USER’S MANUAL Page 3
2.
KEYPAD LAYOUT 7015 and 7005
7
a-
MODEL7OOS
MODEL7015
LCD KEYI’AD
4
2
LED KEYPAD
The 7015 contains indicator lights for the zone status, and the 7005 keypad
contains a two line English language display.
1) ZONE STATUS INDICATORS - Your protected location has been divided into
areas of protection known as zones. The zone indicators display the current
status of each zone as follows:
Fast blinking.
ALARM
Slow blinking low intensity.
BYPASS
Slow pulse
TROUBLE
NOT READY
Solid ON
OFF
READY
2) READY Indicates whether the system is ready for arming.
3) ARM/DISARM IND. Indicates system is armed (ON)/disarmed (OFF).
4) STAY- indicates system is armed with the interior zones bypassed.
5) INSTANT - Indicates system is ARMED with all delay zones instant.
6) AC - indicates system is running on AC,(ON) or backup battery (OFF).
7) BAT - Indicates low battery. Slow pulse = low battery, OFF = Normal
8) COM Indicates a communications failure with the Central station
9) NUMERICAL KEYPAD operates in a similar manner to a calculator or
telephone with the digits 0 - 9 and # clearly marked.
10) DISPLAY AREA - This section of the LCD keypad displays the current
system status in this two line display. The second line of this display can be
rogrammed by your installer to contain customized descriptors for the areas
f protection within your location. The OFF-NORMAL installer programming
mode is identified by a flashing READY (on LED models) and by the display
“PROGRAM MODE’ on LCD keypads.The panel is disabled in this mode. Call
for service if this condition persists.
l
*
XL-3 USER’S MANUAL Page 4
i
ii /3.
KEYPAD CONVENTIONS
i
Throughout this users manual the following conventions are used to display the
keystrokes required to perform the functions.
BYPASS
INSTANT
Key labeled BYPASS on keypad.
Key labeled INSTANT on keypad
Key labeled STAY on keypad.
Key labeled CODE on keypad
Four digit user code.
STAY
CODE
l?JSJW
4. ARMING THE SYSTEM
ARMING the system will activate all portions of your Security System. Arming
can only be performed if all zones are READY. For example, if a protected door
is open the system cannot be armed.
SYSTEMREADY
The system is ready to be armed if the READY indicator light ON (LED- basq?
._ /’
keypads). On LCD-based keypads the following display will appear:
1SYSTEM READY
I
If the system is ready, ARMING can be performed as follows;
ARMING PROCEDURE:
1. Enter your four digit user code into the keypad: [USER]
The ARMED indicator light wili’now be lit and if you are leaving the home you
may exit through a door designated by your installer as an exit/entry zone for a
fixed time period known as the exit delay. The entry exit times for your system
are as follows;
ENTRY:
seconds- EXIT:
seconds
LCD keypads will display the following message;
NOTE: For commercial systems (XLSB) installation, a 2 sec. Bell Test is
provided. Following receipt of the off-premise transmission from the control at
the central station, several beeps are heard from the keypad as confirmation.
If neither of these conditions
occur, CALL FOR SERVICE.
I
p’
NOTE: The system can be armed without the backup battery connected.,
XL-3 USER’S MANUAL Page 5
’
:
I
SYSTEM NOT READY
If the system is not ready to be armed the READY indicator will be OFF. On LED
based keypads the zone indicator lights will .display the zones which are
currently not re,ady.The condition of each zone indicator reflects the status of
each zone as follows;
ALARM
TROUBLE
NOT READY
BYPASS
Fast blinking
Slow pulse
Solid ON
Slow blinking/low intensity
The LCD keypad a display indicates the system is not ready followed by
displays showing the zone number and description of the faulted zone.
For example:
SYSTEM NOT READY
In this example, the front door is not ready (Zone 1). In order to make the system
ready determine which zones are not ready by observing the zone indicator
lights, or the display section of the LCD keypad. From the zone number you can
find out which area of protection is not ready, For example, assume the zone 1
is not ready. Typically, this might mean that a protected door or window is open.
l
Once the problems with each zone have been resolved the READY
light will appear and the system can be armed.
To ARM the system when the system is NOT READY one of the following
actions are necessary:
l
.
Make the zone(s) ready. Determine which zones are not ready and
perform what is necessary to ready the zone(s) (example, close the
door or window, etc.), or
Bypass the zone(s) not ready. Bypassing should only be performed
if the zone cannot be made ready or intentionally will remain not
ready. Zones that are bypassed are not protected when the system
is armed.
XL-3 USER’S MANUAL Page 6’
/” /~ DISARMING
’
f
Disarming the security system will deactivate the system’s burglary function.
This procedure can also be used to reset your system if you accidentally set off
the system (example, o#ened a window while the system was armed, or
excessive amount of smoke activated fire protection system).
DISARM PROCEDURE:
[US.ER] ’
Enter your user code.
IF NO ALARMS HAVE TAKEN PLACE
Upon disarming the ARMING indicator will go off.
The system display will reflect the current status. LCD keypads should display
the SYSTEM READY display.
IF ALARMS HAVE TAKEN PLACE
If alarms or other conditions such as system troubles have taken place sincr?
the initial system arming, they will appear on the display. The conditions thh. 1
have occurred appear in the zone display section of the keypad. LED based
keypads will reflect the current system status through the indicator lights as
follows;
Fast blinking.
ALARM
Slowblinkinglow intensity.
BYPASS
Slow pulse
TROUBLE
SolidON
NOTREADY
Burglary alarms will be indicated with a STEADY sound through the keypad
while FIRE alarms will generate a pulsing sound.
LCD keypads will show the alarm conditions with a display as follows:
This display shows the zones in alarm. After entry of your four digit user code
the following display will appear:
If an intrusion has taken place while you were away, do not enter until the
location has been securedl!!. Call for help from a neighbor’s phone.
.
To clear the display of the alarm or trouble conditions and silence the
/audible signal enter [USER] again.
. ..
XL~USER’SWU~LPage7
6. STAY
The STAY mode deactivates any interior protection zones and you will be free
to walk throughout your location without activating the alarm system. To enter
the STAY mode, the system must be READY. (see previous descrtptlon).
STAY PROCEDURE:
STAY [USER]
Depress the STAY key followed by your user code. After a successful STAY
arming the ARMED indicator will be lit. In addition, on the XL4612RM or
XL4612SM keypad the RDY indicator will slowly blink. On the 7015 keypad the
STAY indicator will be lit. On the LCD keypad the following display will appear;
a
the STAY mode only the external or perimeter burglary protection is active.
ou are free to walk around the residence without activating any of the interior
protection zones
.
.
Remember, you must DISARM the system to when you want to leave
the premise.
Note: The STAY option will automatically be reset after the system is
disarmed.
7. INSTANT
The INSTANT mode arms the system and eliminates the entry time delay
interval. This mode could be used so that if anyone enters through an entry/exit
zone the alarm system will instantly activate. The system must be ready to
select the INSTANT option,
INSTANT PROCEDURE:
INSTANT [USER]
Depress the INSTANT key followed by your user code. Upon successful arming,
the ARMED indicator will be lit. Additionally, keypad the RDY light will blink, the
XL4612RM or XL4612SM. (NOTE: This blink is slightly faster than the indication
for the STAY mode.) On the 7015 keypads the INSTANT indicator will be ON.
The LCD keypad will contain the following message:
m
-
loN:INSTANT
.
Note: The INSTANT option will automatically be reset after the
system is disarmed.
XL-3 USER’S MANUAL Page 8
-8.
INSTANT - STAY
..
_*
x’ ‘(
.-
The INSTANT STAY ‘modearms the system with the characteristics of both the
- INSTANT and STAY.modes with the interior portions bypassed and the entry
delay suspended. The system must be READY to enter this mode.
PROCEDURE:
INSTANT STAY [USER]
STAY LTANT
[USER]
Depress the INSTANT and STAY keys in any order followed by your user code.
After a successful INSTANT STAY arming the ARMED indicator will be lit.
Additionally, the ROY light on XL4612RM and 4612SM keypads will blink slowly
then rapidly. On the 7015 keypads both the INSTANT and STAY lights will be
ON-The 7005 keypad will contain the following message;
yF5Fmiq
.
9.
r ,/\
“.
You cannot exit the premises through an exit/entry zone while the
system is armed in this mode.
BYPASS
Bypasses are performed to eliminate burglary zones that are not ready or faulty
from activating the security system.
BYPASS PROCEDURE:
BYPASS [USER] ZN
Depress the BYPASS key followed by your user code and two digit zone
number (01-12) to be bypassed. Example: BYPASS [USER] 02 bypasses zone
2. If the zone has been bypassed already, the sequence will unbypass the zone
(except if the system is armed and the unbypassed zone is still not ready).
Unbypass returns the zone to protected status.
After the bypass (or unbypass) command has been accepted the unit will emit
a continuous beep and bypassed zones appear in a slow blinking mode in the
zone status area on the XL4612RM, XL4612SM or 7015 keypads. The 7005
LCD keypad displays the zone bypasses as a secondary display after the
SYSTEM READY or SYSTEM NOT READY as shown below:
-1
If multiple zones are bypassed then more than one display will appears ,
Remember: Zones which are bypassed are not protected when the system is
armed. Temporary users (i.e. babysitters) shall be shown the bypass procedure.
XL-3 USER’S MANUAL Page Q
10. UNBYPASS
The UNBYPASS function removes an existing bypass from a currently
bypassed zone. After UNBYPASSING a zone, the bypass removed for that
zone on either the LCD or LED keypad. The procedure is similar to a bypass.
UNBYPASS PROCEDURE:
BY PASS [USER] ZN See bypass description.
11. USER DEFINITION
Users can be entered or modified directly through the keypad. The secur’ky
system can have up to thirty different users. Users number 1 & number 2 are
known as the master users and are the only users allowed to modify other user
operating parameters.
USER DEFINITION PROCEDURE:
CODE [USER] [US number ] [USERID]
ere;
CODE is the CODE key on the keypad
[USER] master user code [User number 1 or User number 2, four digits).
[US number ] User number (01-30)+
[USID] New user ID (0000 - 9999).
Note: (+)lfambush code capability has been enabled by your installing company
then user number 30 will be used as the system ambush code. If an arming only
code (maid code) has been defined by your installer then user number 29 can
only arm the system. If a single user door strike code has been created by your
installer then user number 28 is dedicated to that function.
Please check with your installer to determine whether any of these special
purpose users codes exist.
Example:
To create user number 13, with a user access code of 4667, (assume a’master
user code of 1492), enter; CODE 1492 13 4567
.
Any error detected during the USER definition process will cause the
keypad to beep rapidly four times. If an error is detected retry the
entire command.
Obvious codes like 1111or 1234 should be avoided.
XL-3 USER’S MANUAL Page 10
12. USER DELETION
Removal of users from the panel can be performed as follows;
USER DELETION PROCEDURE:
CODE [USER] [User number ] #
Where:
CODE is the depression of the CODE key.
[USER] Master user code
[User number ] Represents the user number being deleted (03-30). Note:
Master users (User number 1 or number 2) cannot be deleted.
# is the # key from the keypad.
Example: Delete user number 26 (assume a master user code of 6789):
CODE 6789 26 #
13. KEYPAD AUXILIARY CONDITIONS
,-
The system can also initiate three separate AUXILIARY conditions dire&. j
through the keypad. These conditions must be activated by your installer and
can be initiated through simultaneous depression of two keys as follows:
KFYS-
Panic
Fire
Aux.
l
#
7 9
1 3
For example, to initiate a keypad panic signal press the and #keys at the same
time. Consult with your alarm installer to determine the operation of these
conditions within your system. In UL installations, the AUX alarm is silent. The
4612SM keypad has keys for specially defined auxiliary functions. Their
functions are activated by simultaneously depressing two keys. NOTE: Consult
your installer to determine the auxiliary functions of your system.
l
14. DURESS
Ambush can be programmed by your installer to send an emergency signal to
the Central Station if you are forced to enter the premises. If active, code
number 30 is ambush code.
15. ARM-ONLY (MAID) CODE
If selected by your installer, the user code number 29 can only arm the system.
This allows a temporary worker to only arm the security system as they
XL-3 USER’S MANUAL Page 11
10. UNBYPASS
The UNBYPASS function removes an existing bypass from a currently
bypassed zone. After UNBYPASSING a zone, the bypass removed for that
zone on either the LCD or LED keypad. The procedure is similar to a bypass.
UNBYPASS PROCEDURE:
BYPASS [USER] ZN See bypass description.
11. USER DEFINITION
Users can be entered or modified directly through the keypad. The security
system can have up to thirty different users. Users number 1 & number 2 are
known as the master users and are the only users allowed to modify otheruser
operating parameters.
USER DEFINITION PROCEDURE:
CODE [USER] [US number ] [USERID]
.’
”
CODE is the CODE key on the keypad
[USER] master user code [User number 1 or User number 2, four digits).
[US number ] User number (Ol-30)+
[USID] New user ID (0000 - 9999).
Note: (*)lf ambush code capability has been enabled by your installing company
then user number 30 will be used as the system ambush code. If an arming only
code (maid code) has been defined by your installer then user number 29 can
only arm the system. If a single user door strike code has been created by your.
installer then user number 28 is dedicated to,that function.
Please check with your installer to determine whether any of these special
purpose users codes exist.
Example:
To create user number 13, with a user access code of 4567, (assume a master
user code of 1492), enter; CODE 1492 13 4567
.
Any error detected during the USER definition process will cause the
keypad to beep rapidly four times. If an error is detected retry the
entire command.
Obvious codes like 1111or 1234 should be avoided.
0
XL-3 USER’S MANUAL Page 10
12. USER DELETION
Removal of users from the panel can be performed as follows;
USER DELETION PROCEDURE:
CODE [USER] [User number ] #
Where:
CODE is the depression of the CODE key.
[USER] Master user code
[User number ] Represents the user number being deleted (03-30). Note:
Master users (User number 1 or number 2) cannot be deleted.
# is the # key from the keypad.
Example: Delete user number 26 (assume a master user code of 6789):
CODE 6789 26 #
13. KEYPAD AUXILIARY’CONDITIONS
The system can also initiate three separate AUXILIARY conditions direct,,
through the keypad. These conditions must be activated by your installer and
can be initiated through simultaneous depression of two keys as follows:
ON
Panic
Fire
Aux.
KEYSTROKES
’ #
7 9
1 3
For example, to initiate a keypad panic signal press the l and #keys at the same
time. Consult with your alarm installer to determine the operation of these
conditions within your system. In UL installations, the AUX alarm is silent. The
4612SM keypad has keys for specially defined auxiliary functions. Their
functions are activated by simultaneously depressing two keys. NOTE: Consult
your installer to determine the auxiliary functions of your system.
14. DURESS
Ambush can be programmed by your installer to send an emergency signal to
the Central Station if you are forced to enter the premises. If active, code
number 30 is ambush code.
15. ARM-ONLY (MAID) CODE
.
i
If selected by your installer, the user code number 29 can only arm the system.
This allows a temporary worker to only arm the security system as they leave.
,?
>.. / ’
XL3 USER’S MANUAL Page 11
16. DOOR STRIKE USER CODE *
In certain installations there may be a door (or other device) which is
programmed to activate by entering a user code. If configured by your installer,
number 28 can be dedicated for this purpose. If programmed, then entering
user number 28 will not arm or disarm the system but will activate an external
device such as a door strike. This feature has not been investigated by UL. The
system is not Listed for Access Control applications.
17. KEYPAD TAMPER
If 21 characters have been entered without a valid user code or command, the
keypad will beep continuously. Silence by entering a valid user code.
18. QUICK ARMING (# 1)
When selected by the installer, this command will arm the system without entry
a user code. NOTE: System disarming will require a user code. To quick arm
ter: # 1
19. QUICK FORCED ARM (# 2)
When selected by the installer, this command (# 2) arms the system wtthout
entering a user code and bypasses any unready burglary zones. Quick forced
arm:# 2
20. SET TIME OF DAY ( # 3 )
The system contains a real-time clock for the auto-arming and system test
capability. The time of day can be set through any keypad using the following’
command: # 3 [USER] HR MN
Time entry is performed in 24 hour time (military time). For exampleto set the
clock for 10:25PM (assume a user code of 4567) enter: # 3 4567 20 25
l
l
@I.
.NOTE: .lf the..system clock needs to be reset, the XL4612RM,
XL4612SM or 7015 keypads will blink rapidly,,insuccession every 30
seconds. The 7005 keypad will display a message. This could occur
if the time has never been set or if total system power (AC and
battery) was removed for a prolonged period of time.
Consult your installer to determine whether your user code is
necessary for setting the time. This feature is disabled in UL
installations.
ZONE DIRECTORY (# 4 )
To view a list of the zone descriptors from the 7005 keypad, enter: # 4
XL-3 USER’S MANUAL Page 12
22. SET AUTO-ARM TIME (#5)
Another option selectable by your installer is auto arming. This feature means
that the system can be programmed to arm at a preprogrammed time every day.
This will occur at the selected time if the system is not already armed. For
example, if you have an 11:30 PM auto-arming time programmed and fall asleep
without arming the system, the panel will automatically arm at 11:30.
WARNING INDICATOR
Awarning signal can be selected by your installer to provide an audible warning
two minutes prior to the auto- arming time. This warning will repeat every 30
seconds until the auto arming time. To disable, simply enter your four digit user
code. The keypad will emit a beep and the indicator lights on LED based
keypads will blink rapidly to acknowledge that you have removed the
auto-arming time for the day.
HOW TO CHANGE THE AUTO-ARMING TIME
To modify the auto-arming time enter: #5 [USER] HR MN. For example: than f-3
the auto-arming time to 11:45 PM (user code of 5678) enter: # 5 5878 23 45’< ’
.
.
NOTE: All times are entered in 24 hour (military) time.
This feature is disabled in UL installations.
23:CHIME
MODE (#6)
The optional chime mode causes the keypad to beep for one second every time
selected zones such as the entrance door are opened while the system is
disarmed. For example, this could inform you each time the front door was
opened while you.were at home. To activate, press # 6 from the keypad. If the
chime feature has already been turned on, another #6 will turn the feature off.
24. READ CLOCK TIME (#7) LCD Only
Upon entering #7, the LCD display shows the current time.
25. READ AUTO SET TIME (#8) LCD O.nly
Upon entering #8, LCD display shows the time that system will auto-arm.
26. DOdR STRIKE COMMAND (# 9 )’
if enabled by your installer a valid user can activate any of the system door
strikes through the following command: # 9 [USER] [door strike number] For
example: activate door strike 3 (with user code of 2468) enter: # 9 2468 3
XL-3 USER’S MANUAL Page 13
16.
DOOR STRIKE USER CODE
In certain installations there may be a door (or other device) which is
programmed to activate by entering a user code. If configured by your installer,
number 28 can be dedicated for this purpose. If programmed, then entering
user number 28 will not arm or disarm the system but will activate an external
device such as a door strike. This feature hasnot been investigated by UL. The
system is not Listed for Access Control applications.
17.
KEYPAD TAMPER
If 21 characters have been entered without a valid user code or command, the
keypad will beep continuously. Silence by entering a valid user code.
18. QUICK ARMING (# 1)
When selected by the installer, this command will arm the system without entry
user code. NOTE: System disarming will require a user code. To quick arm
19. QUICK FORCED ARM (# 2)
When selected by the installer, this command (# 2) arms the system without
entering a user code and bypasses any unready burglary zones. Quick forced
arm:# 2
20. SET TIME OF DAY ( # 3 )
The system contains a real-time clock for the auto-arming and system test
capability. The time of day can be set through any keypad using the following
command: # 3 [USER] HR MN
Time entry is performed in 24 hour time (military time). For example to set the
clock for 10:25PM (assume a user code of 4567) enter: # 3 4567 20 25
.
l
@!I.
NOTE: if the system clock needs to be reset, the XL4612RM,
XL4812SM or 7015 keypads will blink rapidly in succession every 30
seconds. The 7005 keypad will display a message. This could occur
if the time has never been set or if total system power (AC and
battery) was removed for a prolonged period of time.
Consult your installer to determine whether your user code is
necessary for setting the time. This feature is disabled in UL
installations.
ZONE DIRECTORY (# 4 )
To view a list of the zone descriptors from the 7005 keypad, enter: # 4
XL-3 USER’S MANUAL Page 12
22. SET AUTO-ARM TIME (#5)
Another option selectable by your installer is auto arming. This feature means
that the system can be programmed to arm at a preprogrammed time every day.
This will occur at the selected time if the system is not already armed. For
example, if you have an II:30 PM auto-arming time programmed and fall asleep
without arming the system, the panel will automatically arm at 11:30.
WARNING INDICATOR
Awarning signal can be selected by your installer to provide an audible warning
two minutes prior to the auto- arming time. This warning will repeat every 30
seconds until the auto arming time. To disable, simply enter your four digit user
code. The keypad will emit a beep and the indicator lights on LED based
keypads will blink rapidly to acknowledge that you have removed the
auto-arming time for the day.
HOW TO CHANGE THE AUTO-ARMING TIME
To modify the auto-arming time enter: #5 [USER] HR MN. For example: chanrj
the auto-arming time to 11:45 PM (user code of 5678) enter: # 5 5678 23 45
.
l
NOTE: All times are entered in 24 hour (military) time.
This feature is disabled in UL installations.
23. CHIME MODE (#6)
The optional chime mode causes the keypad to beep for one second every time
selected zones such as the entrance door are opened while the system is
disarmed. For example, this could inform you each time the front door was
opened while you were at home. To activate, press # 6 from the keypad. If the
chime feature has already been turned on, another #6 will turn the feature off.
24. READ CLOCK TIME (#7) LCD Only
Upon entering #7, the LCD display shows the current time.
25. READ AUTO SET TIME (#8) LCD Only
Upon entering #8, LCD display shows the time that system will auto-arm.
26. DOOR STRIKE COMMAND (# 9 )
If enabled by your installer a valid user can activate any. of the system door
strikes through the following command: # 9 [USER] [door strike number] For
example: activate door strike 3 (with user code of 2468) enter: # 9 2468 3
0\ 1
XL-3 USER’S MANUAL Page 13
27.
INSTALLATION
LAYOUT.
.:P ;
i (.,,: 1,“ + .’
‘,.
Early warning fire detection is best achieved by the installation of fire detection
equipment the location as follows;
Typical Smoke Detector Layout
Preparation of an evacuation plan is of prime importance in fire prevention.
Establish a household emergency evacuation plan in the event of fire. Refer to
the Smoke Detector instructions for exact mounting, layout and spacing.
1. Evaluate possible escape routes from your home.
2- Select 2 escape routes from each room.
3. Rooms on the second floor should have a rope ladder. Be sure it will reach
the ground.
4. Draw a sketch of your escape plan so everyone is familiar with it.
5. Practice your escape plan to assure that everyone knows what to do.
6. Establish a meeting place outside where your family is to report. Once you
have evacuated the house do not return to a burning house.
7. Advise the local fire authority that you have installed a fire alarm system.
8. When the fire alarm signals, LEAVE IMMEDIATELY. Do not stop for
belongings.
9. If a fire occurs Jest the door. If hot, use your alternate route. If the door is
cool, brace your shoulder against it and open it cautiously. Shut the door to help
prevent the fire and smoke from spreading. Crawl through smoke, holding your
breath.
0. Contact the Fire Department from a neighbor’s telephone.
Everyone including neighbors should be familiar with the Fire and Burglary
a.
signals. In this installation the Fire Alarm signal is
The Burglary
Alarm signal is
The fire alarm signal takes precedence over
the burglar alarm signal.
XL-3 USER’S MANUAL Page 14
28. SYSTEM TESTING
This Wfltml Unit was
IS best performed by
manufactured under rigid qualiiy standards. Maintenance
your installing company with trained service personnel.
Installing Company:
Telephone Number:
It is recommended that you test your system once a week using the following
procedure:
.
Note: If your system is monitored by a Central Station then contact
them prior to performing this test.
I- Arm your security system.
2- Activate the system by opening a protected zone (example, window, or door).
3- Confirm that the alarm sounding device (bell or siren) activates. If your
System is connected to a Central Station then the keypad will emit a ringb~-)
\\ /
sound to confirm that the signal was received.
4- Disarm the system to silence the system and return to normal status.
BATTERY TEST
In order to test the backup battery the following procedure should be performed;
l- Remove the AC transformer from the AC outlet by removing the restraining
screw which secures the transformer to the wall. (Note: the screw is not present
in models sold in Canada).
2- Observe that the AC light goes off on the keypad.
3- Activate your alarm system using steps l-4 listed above.
4- Replace the AC transformer to the AC outlet and secure using the retaining
screw (Note: The retaining screw is not present in models sold in Canada).
The National Fire Protection Association publishes a standard for household fire
warning equipment. N.F.P.A. #74. Further information can be obtained by
contacting; NFPA Public Affairs Dept., Batterymarch Park, Quincy,MA 02269.
If you have any further questions about the operation of your system, call your
installer.
XL-3 USER’S MANUAL Page 15
,
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable
for use. The FCC requires the following statement for your information.
This equipment generates and uses radio frequency energy and if not installed and
used properly, that is in strict accordance with the manufacturer’s instructions may
cause interference to radio and television reception. lt has been tested and found to
comply with the limits of Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference In a residential installation. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does not cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:lf using an indoor antenna,
have a quality outdoor antenna installed.
.
.
.
.
Reorient the receiving antenna until interference is reduced or eliminated.
Move the radio or television receiver away from the control/ communicator.
Move. the antenna leads away from any wire runs to the
control/communicator.
Plug the control/communicator into a different outlet so that it and the radio
or television receiver are on different branch circuits.
ff necessary, the user should consult the dealer or an experienced radio/television
technician for additional suggestions.
The user may find the following booklet prepared by the Federal Communications
Commission helpful: “interference Handbook”. This booklet is available from ‘the U.S.
Government Printing Office, Washington, DC 20402. Stock No. 004-000-00450-7.
The user shall not make any changes or modifications to the equipment unless
authorized by the installation Instructions or User’s Manual. Unauthorized changes or
modifications could void the user’s authority to operate the equipment.
IN THE EVENT OF TELEPHONE OPERAllONAL PROBLEMS
In the event of telephone operational problems, disconnect the communicator by
removing the plug from the RJ31 X jack. Do not disconnect the phone connection inside
the communicator. Doing so will result in the loss of the phone works correctly after the
communicator has been disconnected from the phone lines, the communicator has a
problem and should be returned for repair.
a
port disconnecting the communicator, there is still a problem on your line, notify the
phone company that they have a problem and request prompt repair service. The
<ser may not under any circumstances (in or out of warranty) attempt any service or
repairs on the system. lt must be returned to the factory or an authorized service agency
for all repairs.
XL-3 USER’SMANUALP-e 16
.
WARNING LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer
guaranteed protection against burglary, fire or other emergency. ‘Any alarm
system, whether commercial or residential, is subject to compromise or failure
to warn for a variety of reasons. For example:
.
Intruders may gain access through unprotected openings or have the
technical sophistication to bypass an alarm sensor or disconnect an
alarm warning device.
.
Intrusion detectors (e.g., passive infrared detectors), smoke
detectors, and many other sensing devices will not work without
power. Battery operated devices will not work without batteries, with
dead batteries or if the batteries are not put in properly. Devices
powered solely by AC will not work if their AC power supply is cut off
for any reason, however briefly.
l
.
Signals sent by wireless transmitters may be blocked or reflected by ’
metal before they reach the alarm receiver. Even if the signal path
has been recently checked during a weekly test, blockage can occur
if a metal object is moved into the path.
A user may not be able to reach a panic or emergency button quickly
enough.
.
While smoke detectors have played a key role in reducing residential
fire deaths in the United States, they may not activate or provide early
warning for a variety of reasons in as many as 35% of all fires,
according to data published by the Federal Emergency Management
Agency. Some of the reasons smoke detectors used in conjunction
with this System may not work are as follows: Smoke detectors may
have been improperly installed and positioned. Smoke detectors may
not sense fires that start where smoke cannot reach the detectors,
such as in chimneys, in walls, or roofs, or on the other side of closed
doors. Smoke detectors may not sense a fire on another level of a
residence or building. A second floor detector, for example, may not
sense a first floor or basement fire. Moreover, smoke detectors have
sensing limitations. No smoke detector can sense every kind of fire
every time. In general, detectors may not always warn about fires
caused by carelessness and safety hazards like smoking in bed,
violent explosions, escaping gas, improper storage of flammable
materials, overloaded electrical circuits, children playing with
matches, or arson. Depending on the nature of the fire and/or the
location of the smoke detectors, the detector, even if it operates ?“,
anticipated, may not provide sufficient warning to allow all occupant-,.
to escape in time to prevent injury or death.
.
Passive Infrared Motion Detectors can only detect intrusion within the
designed ranges as diagramed in their installation manual. Passive
I
XL-3 USER’S MANUAL Page 17
Infrared Detectors do not provide volumetric area protection. They do
create multiple beams of protection, and intrusion can only be
detected in unobstructed areas covered by the beams. They cannot
detect motion or intrusion that takes place behind walls, ceilings,
floors, closed doors, glass partitions, glass doors, or window.
Mechanical tampering, masking, painting, or spraying of any material
on the mirrors, windows or any part of the optical system can reduce
their detection ability. Passive Infrared Detectors sense changes in
temperature; however, as the ambient temperature of the protected
area approaches the temperature range of 90 to 15OF,the detection
performance can decrease.
.
l
.
l
Alarm warning devices such as sirens, bells or horns may not alert
people or wake up sleepers who are located on the other side of
closed or partly open doors. If warning devices sound on a different
level of the residence from the bedrooms, then they are less likely to
waken or alert people inside the bedrooms. Even persons who are
awake may not hear the warning if the alarm is muffled by noise from
a stereo, radio, air conditioner or other appliances, or by passing
traffic. Finally, alarm warning devices, however loud, may not warn
hearing-impaired people or waken deep sleepers.
Telephone lines needed to transmit alarm signals from a premises to
a central monitoring station may be out of service or temporarily out
of setvice. Telephone lines are also subject to compromise by
sophisticated intruders.
Even if the system responds to the emergency,as intended, however,
occupants may have insufficient time to protect themselves from the
emergency situation. In the case of a monitored alarm system,
authorities may not respond appropriately.
This equipment, like other electrical devices, is subject to component
failure. Even though this equipment is designed to last as long as 10
years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion
or fire occurs is inadequate maintenance. This alarm system should be tested
weekly to make sure all sensors are working properly.
Installing an alarm system may make one eligible for lower insurance rates, but
an alarm system is not a substitute for insurance. Homeowners, property
owners and renters should continue to act prudently in protecting themselves
and continue to insure their lives and property.
continue to develop new and improved protection devices. Users of alarm
a
>ystems owe it to themselves and their loved ones to learn about these
developments.
XL-3 USER’S MANUAL Page 18
i
’
OWNERS INFORMATION
PERSONAL
ADDRESS:
CITY, STATE, ZIP:
TELEPHONE NUMBER:
EMERGENCY NUMBERS
CENTRAL STATION:
FIRE DEPARTMENT:
\
/’
POLICE DEPARTMENT:
NEIGHBOR:
GAS/ELECTRIC COMPANY:
DOCTOR:
HOSPITAL:
EMERGENCY:
SERVICE INFORMATION
ALARM INSTALLING COMPANY:
c/
XL-3 USER’S MANUAL Page 19
32. SUMMARY
PROCEDURE
ARM SYSTEM
DISARM SYSTEMI
SILENCE CONDITION
STAY
INSTANT-STAY
BYPASS
UNBYPASS
DISARM
USER DEFINITION
USER DELETION
SEQUENCE
[USER1
[USER]
[USER]
STAY [USER]
INSTANT-STAY [USER] OR
STAY INSTANT USER
BYPASS [USER] [Zn]
BYPASS [Zn] If zone is already bypassed
[USER]
CODE [USER] USER NUMBER] [USID]
CODE [USER] [USER NUMBER] #
KEYPAD AUXILIARY CONDITIONS
l#
79
13
PANIC
FIRE
AUX.
QUICK COMMANDS
QUICK ARM
QUICK FORCED ARM
TIME SET
ZONE DIRECTORY (‘)
SET AUTO-ARMING TIME
CHIME MODE
DISPLAY CLOCK TIME (‘)
DISPLAY AUTO-ARM TIME (‘)
DOOR STRIKE
l
#1
#2
#3 [USER] HH MM
#4
#5 [USER] HH MM
#6
#7
#8
#9 [USER] [TRIGGER NUMBER]
LCD KEYPADS ONLY
NOTE: The time needs to be set if all of the LEDS on the LED based keypads
blink rapidly every 30 seconds.
XL-3 USER’S MANUAL Page 22
FIRE BURGLARY INSTRUMENTS, INC. ONE YEAR UMlTED WARRANTY
Fire Burglary Instruments, Inc., a subsidiary of Pittway Corporation, its divisions,
subsidiaries and affiliates (“Seller”), warrants its security equipment (“the product”) to
be free from defects in materials and workmanship one year from the date of original
purchase, under normal use and service. Seller’s obligation is limited to repairing or
replacing, at its option, free of charge for parts, labor, or transportation, any product
proven to be defective in materials or workmanship under normal use and service. Seller
shall have no obligation under this warranty or otherwise if the product is altered or
improperly repaired or serviced by anyone other than Seller. In case of defect, contact
the securii professional who installed and maintains your security equipment or the
Seller for product repair.
This one year Limited Warranty is in lieu of all other express warranties, obligations or
liabilitiesTHERE ARE NO EXPRESS WARRANTIES WHICH EXTEND BEYOND THE
FACE HEREOF.ANY IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES MADE
BY SELLER IN CONNECTION WITH THIS PRODUCT, INCLUDING ANY IMPLIF
-?
WARRANTY OF MERCHANTA.BILITY,OR FITNESS FOR A PARTICULAR PURPG. ’
OR OTHERWISE, ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM
THE DATE OF ORIGINAL PURCHASE. ANY ACTION OR BREACH OF ANY
WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY, MUST BE BROUGHT WITHIN 18 MONTHS FROM DATE OF
ORIGINAL PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS
OF LIABILITY WHATSOEVER, EVEN THE LOSS OR DAMAGE IS CAUSED BY ITS
OWN NEGLIGENCE OR FAULT. Some states do not allow limitation on how long an
implied warranty lasts or the exclusion or limitation on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Seller does not represent that the products it sells may not be compromised or
circumvented; that the product will prevent any personal injury or property loss by
burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate
warning or protection. Buyer understands that a properly installed and maintained alarm
may only reduce the risk of a buiglary, robbery, or fire or other events occurring without
providing an alarm, but it is not insurance or a guarantee that such will not occur or
that there will be no personal
injury or property
loss as a result.
CONSEQUENTLYSELLER SHALL HAVE NO LlA,BlLlTY FOR ANY PERSONAL
INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE
PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE,
WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING
UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSF
(7
OR ORIGINSELLERS MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCE\,
THE PURCHASE PRICE OF’THE PRODUCT, WHICH SHALL BE THE COMPLEIt ’
AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state. No increase
or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.