Cordless Multi Tool

ENGLISH: Original instructions
INSTRUCTION MANUAL
Cordless Multi Tool
TM30D
Read before use.
SPECIFICATIONS
Model:
TM30D
6,000 - 20,000 min-1
Oscillation per minute
Oscillation angle, left/right
1.6° (3.2° total)
Rated voltage
D.C. 10.8 V - 12 V max
Battery cartridge
BL1016, BL1021B
BL1041B
277 mm
296 mm
without dust extraction
attachment
1.1 kg
1.2 kg
with dust extraction
attachment
1.2 kg
1.3 kg
Overall length
Net weight
•
•
•
Duetoourcontinuingprogramofresearchanddevelopment,thespeciicationshereinaresubjecttochange
without notice.
Speciicationsandbatterycartridgemaydifferfromcountrytocountry.
Weight,withbatterycartridge,accordingtoEPTA-Procedure01/2003
Symbols
Thefollowingshowthesymbolsusedfortheequipment. Be sure that you understand their meaning before
use.
Uncertainty(K):3dB(A)
Workmode:Scraping
Soundpressurelevel(LpA):81dB(A)
Soundpowerlevel(LWA):92dB(A)
Uncertainty(K):3dB(A)
WARNING: Wear ear protection.
Read instruction manual.
Vibration
Wearsafetyglasses.
Thevibrationtotalvalue(tri-axialvectorsum)determinedaccordingtoEN60745:
Workmode:Sanding
Vibration emission (ah):2.5m/s2 or less
Uncertainty(K):1.5m/s2
Workmode:Cuttingwithplungecutsawblade
Vibration emission (ah):10.5m/s2
Uncertainty(K):1.5m/s2
Workmode:Cuttingwithsegmentalsawblade
Vibration emission (ah):5.5m/s2
Uncertainty(K):1.5m/s2
Workmode:Scraping
Vibration emission (ah):9.0m/s2
Uncertainty(K):1.5m/s2
OnlyforEUcountries
Donotdisposeofelectricequipment
together with household waste material! In
observanceoftheEuropeanDirective,on
WasteElectricandElectronicEquipment
and its implementation in accordance with
nationallaw,electricequipmentthathave
reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
Intended use
Thetoolisintendedforsawingandcuttingwood,
plastic, gypsum, non-ferrous metals, and fastening
elements (e. g. unhardened nails and staples). It is also
intended for working soft wall tiles, as well as dry sanding and scraping of small surfaces. It is especially for
workingclosetoedgeandlushcutting.
NOTE:Thedeclaredvibrationemissionvaluehas
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE:Thedeclaredvibrationemissionvalue
may also be used in a preliminary assessment of
exposure.
Noise
ThetypicalA-weightednoiseleveldeterminedaccordingtoEN60745:
Workmode:Sanding
Soundpressurelevel(LpA):75dB(A)
Uncertainty(K):3dB(A)
WARNING:Thevibrationemissionduringactual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
Thenoiselevelunderworkingmayexceed80dB(A).
Workmode:Cuttingwithplungecutsawblade
Soundpressurelevel(LpA):82dB(A)
Soundpowerlevel(LWA):93dB(A)
Uncertainty(K):3dB(A)
Workmode:Cuttingwithsegmentalsawblade
Soundpressurelevel(LpA):81dB(A)
Soundpowerlevel(LWA):92dB(A)
WARNING: Be sure to identify safety measures
to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
2
ENGLISH
5.
EC Declaration of Conformity
For European countries only
MakitadeclaresthatthefollowingMachine(s):
DesignationofMachine:CordlessMultiTool
ModelNo./Type:TM30D
ConformstothefollowingEuropeanDirectives:
2006/42/EC
Theyaremanufacturedinaccordancewiththefollowing
standardorstandardizeddocuments:EN60745
Thetechnicalileinaccordancewith2006/42/ECis
availablefrom:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
24.9.2015
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and instructionsmayresultinelectricshock,ireand/orseriousinjury.
Save all warnings and instructions for future reference.
Theterm"powertool"inthewarningsreferstoyourmains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive atmospheres, such as in the presence of lammable
liquids, gases or dust.Powertoolscreatesparks
which may ignite the dust or fumes.
3.
Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
Electrical Safety
1.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiiedplugsandmatchingoutletswill
reduce risk of electric shock.
2.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.Thereisanincreasedriskofelectric shock if your body is earthed or grounded.
3.
Do not expose power tools to rain or wet conditions.Waterenteringapowertoolwillincrease
the risk of electric shock.
4.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
3
6.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use.Useofacord
suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.UseofanRCDreduces
the risk of electric shock.
Personal Safety
1.
Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inluence of drugs, alcohol or medication.Amomentofinattentionwhileoperating
powertoolsmayresultinseriouspersonalinjury.
2.
Use personal protective equipment. Always wear eye
protection.Protectiveequipmentsuchasdustmask,nonskid safety shoes, hard hat, or hearing protection used for
appropriateconditionswillreducepersonalinjuries.
3.
Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
youringerontheswitchorenergisingpowertools
that have the switch on invites accidents.
4.
Remove any adjusting key or wrench before
turning the power tool on.Awrenchorakeyleft
attached to a rotating part of the power tool may
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times.Thisenablesbettercontrol
of the power tool in unexpected situations.
6.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts.Looseclothes,jewellery or long hair can be caught in moving parts.
7.
If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.Useof
dust collection can reduce dust-related hazards.
Power tool use and care
1.
Do not force the power tool. Use the correct
power tool for your application.Thecorrect
powertoolwilldothejobbetterandsaferatthe
rate for which it was designed.
2.
Do not use the power tool if the switch does not turn
it on and off.Anypowertoolthatcannotbecontrolled
with the switch is dangerous and must be repaired.
3.
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.Suchpreventive safety measures reduce the risk of starting
the power tool accidentally.
4.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.Powertoolsaredangerousinthe
hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
ENGLISH
6.
7.
7.
Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking into account the working conditions and
the work to be performed.Useofthepowertool
for operations different from those intended could
result in a hazardous situation.
Battery tool use and care
1.
Recharge only with the charger speciied by
the manufacturer.Achargerthatissuitablefor
onetypeofbatterypackmaycreateariskofire
when used with another battery pack.
2.
Use power tools only with speciically designated battery packs.Useofanyotherbattery
packsmaycreateariskofinjuryandire.
3.
When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.Shortingthebatteryterminalstogethermaycauseburnsoraire.
4.
Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If contact accidentally occurs, lush with water. If
liquid contacts eyes, additionally seek medical
help.Liquidejectedfromthebatterymaycause
irritation or burns.
Service
1.
Have your power tool serviced by a qualiied
repair person using only identical replacement
parts.Thiswillensurethatthesafetyofthepower
tool is maintained.
2.
Follow instruction for lubricating and changing accessories.
3.
Keep handles dry, clean and free from oil and
grease.
Cordless multi tool safety warnings
1.
2.
3.
4.
5.
6.
This power tool is intended to function for
sawing, cutting, grinding and sanding. Read all
safety warnings, instructions, illustrations and
speciications provided with this power tool.
Failure to follow all instructions listed below may
resultinelectricshock,ireand/orseriousinjury.
Hold power tool by insulated gripping surfaces, when performing an operation where
the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
Use clamps or another practical way to secure
and support the workpiece to a stable platform. Holding the work by hand or against your
body leaves it unstable and may lead to loss of
control.
Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT safety
glasses.
Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
Hold the tool irmly.
4
Make sure the application tool is not contacting the workpiece before the switch is turned
on.
8.
Keep hands away from moving parts.
9.
Do not leave the tool running. Operate the tool
only when hand-held.
10. Always switch off and wait for the blade to
come to a complete stop before removing the
blade from the workpiece.
11. Do not touch the application tool or the workpiece immediately after operation; they may be
extremely hot and could burn your skin.
12. Do not operate the tool at no-load
unnecessarily.
13. Always use the correct dust mask/respirator
for the material and application you are working with.
14. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier
safety data.
15. This tool has not been waterproofed, so do not
use water on the workpiece surface.
16. Ventilate your work area adequately when you
perform sanding operations.
17. Use of this tool to sand some products, paints
and wood could expose user to dust containing hazardous substances. Use appropriate
respiratory protection.
18. Be sure that there are no cracks or breakage
on the pad before use. Cracks or breakage
may cause a personal injury.
19. Do not use accessories which are not speciically designed and recommended by the tool
manufacturer. Just because the accessory
can be attached to your power tool, it does not
assure safe operation.
20. Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As appropriate, wear hearing protectors, gloves and
workshop apron capable of stopping small
abrasive or workpiece fragments.Theeyeprotectionmustbecapableofstoppinglyingdebris
generatedbyvariousoperations.Thedustmask
orrespiratormustbecapableofiltratingparticles
generatedbyyouroperation.Prolongedexposure
to high intensity noise may cause hearing loss.
21. Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken accessory
maylyawayandcauseinjurybeyondimmediate
area of operation.
22. Never lay the power tool down until the accessory has come to a complete stop.Thespinning
accessory may grab the surface and pull the
power tool out of your control.
23. Do not run the power tool while carrying it at
your side.Accidentalcontactwiththeaccessory
could snag your clothing, pulling the accessory
into your body.
24. Do not operate the power tool near lammable
materials.Sparkscouldignitethesematerials.
ENGLISH
25. Do not use accessories that require liquid
coolants.Usingwaterorotherliquidcoolants
may result in electrocution or shock.
26. Always be sure that the tool is switched off
and unplugged or that the battery cartridge is
removed before carrying out any work on the tool.
27. Always be sure you have a irm footing. Be
sure no one is below when using the tool in
high locations.
SAVE THESE INSTRUCTIONS.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum
battery life
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
1.
2.
Important safety instructions for
battery cartridge
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
CAUTION: Only use genuine Makita batteries.
Useofnon-genuineMakitabatteries,orbatteriesthat
have been altered, may result in the battery bursting
causingires,personalinjuryanddamage.Itwill
also void the Makita warranty for the Makita tool and
charger.
3.
Before using battery cartridge, read all instructions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
Do not disassemble battery cartridge.
If operating time has become excessively shorter,
stop operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridge in a container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current low,
overheating, possible burns and even a breakdown.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a ire.
Be careful not to drop or strike battery.
Do not use a damaged battery.
The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties,
forwardingagents,specialrequirementonpackaging and labeling must be observed.
For preparation of the item being shipped, consultinganexpertforhazardousmaterialisrequired.
Pleasealsoobservepossiblymoredetailed
national regulations.
Tapeormaskoffopencontactsandpackupthe
battery in such a manner that it cannot move
around in the packaging.
Follow your local regulations relating to disposal of battery.
5
Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
Never recharge a fully charged battery cartridge. Overcharging shortens the battery
service life.
Charge the battery cartridge with room temperature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION: Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery cartridge irmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridgeirmlymaycausethemtoslipoffyourhands
and result in damage to the tool and battery cartridge
andapersonalinjury.
2
1
3
Fig.1
1. Red indicator 2. Button 3. Battery cartridge
Toremovethebatterycartridge,slideitfromthetool
while sliding the button on the front of the cartridge.
ENGLISH
Toinstallthebatterycartridge,alignthetongueonthe
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
Indicator lamps
Lighted
Remaining
capacity
Off
75%to100%
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
itmayaccidentallyfalloutofthetool,causinginjuryto
you or someone around you.
50%to75%
25%to50%
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
0%to25%
Battery protection system
Thetoolisequippedwithabatteryprotectionsystem.
Thissystemautomaticallycutsoffpowertothemotorto
extend battery life.
Thetoolwillautomaticallystopduringoperationifthe
tool and/or battery are placed under one of the following
conditions:
Overloaded:
Thetoolisoperatedinamannerthatcausesittodraw
an abnormally high current.
In this situation, turn the tool off and stop the application
thatcausedthetooltobecomeoverloaded.Thenturn
the tool on to restart.
If the tool does not start, the battery is overheated. In
this situation, let the battery cool before turning the tool
on again.
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Switch action
CAUTION: Before installing the battery cartridge into the tool, always check to see that the
tool is switched off.
1
Low battery voltage:
Theremainingbatterycapacityistoolowandthetool
will not operate. If you turn the tool on, the motor runs
again but stops soon. In this situation, remove and
recharge the battery.
Indicating the remaining battery
capacity
Fig.3
1.Slideswitch
Tostartthetool,slidetheslideswitchtowardthe“I
(ON)” position.
Tostopthetool,slidetheslideswitchtowardthe“O
(OFF)” position.
Only for battery cartridges with "B" at the end of the
model number
1
2
Fig.2
1. Indicator lamps 2. Check button
Pressthecheckbuttononthebatterycartridgetoindicatetheremainingbatterycapacity.Theindicatorlamps
light up for few seconds.
6
ENGLISH
Adjusting the orbital stroke rate
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
1
Installing or removing application
tool
Optional accessory
WARNING: Do not install application tool
upside down. Installing application tool upside down
maydamagethetoolandcauseseriouspersonalinjury.
NOTE: Install application tool in the correct direction according to your work.Applicationtoolcanbe
installed at an angle of every 30 degree.
Fig.4
1. Dial
ToInstallanapplicationtool(optionalaccessory),puttheapplicationtoolonthetoollangesothattheprotrusionsofthetool
langeitintheholesintheapplicationtool.Thensecurethe
applicationtoolbytighteningtheboltirmlywiththehexwrench.
Theorbitalstrokerateisadjustable.Tochangethe
orbitalstrokerate,turnthedialbetween1and5.The
higher the number is, the higher the orbital stroke rate is.
Presetthedialtothenumbersuitableforyourworkpiece.
NOTE: Thedialcannotbeturneddirectlyfrom1to5orfrom5to1.
Forcingthedialmaydamagethetool.Whenchangingthedialdirection, always turn the dial moving it through each intermediate number.
2
3
Lighting up the front lamp
CAUTION: Do not look in the light or see the
source of light directly.
1
Fig.6
1.Protrusionsofthetoollange2. Holes in the
application tool 3.Applicationtoolinstallationbolt
2
1
1
Fig.5
1. Front lamp
3
Slidetheslideswitchtowardthe"I(ON)"positionto
lightupthefrontlamp.Thelampkeepsonlightingwhile
theswitchisthe"I(ON)"position.
Thelightautomaticallygoesoutafterpressingtherear
of the slide switch, and then sliding the slide switch
towardthe"O(OFF)"position.
Overload protection
Whenthetoolisoverloadedandtemperatureofthetoolorthe
battery cartridge reaches a certain level, the front lamp blinks
and the tool automatically stops. Remove a cause of overload,
and cool down the tool and the battery cartridge to restart.
7
Fig.7
1.Applicationtoolinstallationbolt2. Hex wrench
3.Tighten
Toremovetheapplicationtool,loosenandremovethe
application tool installation bolt using a hex wrench and
then take off the application tool.
Whenusingthetoolasasander,setasandingpaper
onthesandingpad(hookandloopitting).
Make sure that their shape and dust extraction holes
match each other when setting.
ENGLISH
OPERATION
3
WARNING: Before starting the tool and
during operation, keep your hand and face away
from the application tool.
CAUTION: Do not apply excessive load to the
tool which may cause a motor lock and stop the tool.
2
CAUTION: Do not operate the tool with pressing the battery cartridge against the tool.
1
Cutting, sawing and scraping
CAUTION: Do not move on the tool forcibly in
the direction (eg. towards either side) of tool application with no cutting edge. It may damage the tool.
Fig.8
1.Sandingpad2.Tighten3.Sandingpaper
Toremovethesandingpaper,raiseitsendandpeelitoff.
Whenusingapplicationtoolswithadifferenttypeof
installation section, use a correct adapter (optional
accessory).
2
1
3
Fig.11
Puttheapplicationtoolontheworkpiece.
Andthenmovethetoolforwardsothattheapplication
tool movement does not slow down.
NOTE: Forcing or excessive pressure on the tool may
reduceeficiency.
4
NOTE: Before cutting operation, it is recommended to
presettheorbitalstrokerate3-5.
Fig.9
1.Applicationtoolinstallationbolt2. Holes in the
application tool 3.Adapter(requiredforsomeapplication tools) 4.Protrusionsofthetoollange
Sanding
CAUTION: Do not reuse a sanding paper used
for sanding metal to sand wood.
Hex wrench storage
CAUTION: Do not use a worn sanding paper
or sanding paper without grit.
Applyasandingpaperontheworkpiece.
Fig.10
1. Hex wrench
1
Whennotinuse,storethehexwrenchasshowninthe
iguretokeepitfrombeinglost.
Fig.12
8
ENGLISH
NOTE:Usingatestmaterialsampletotryisrecommendable to determine a correct orbital stroke rate
suitable for your work.
NOTE:Useasandingpaperwiththesamegrituntil
sanding the whole workpiece is completed. Replacing
a sanding paper with different grit sanding paper may
notgetaineinish.
Dust extraction attachment
Optional accessory
CAUTION: Do not use the dust extraction
attachment when sanding metal.Suckingspark
and hot particle results in smoking and ignition.
5
Fig.14
MAINTENANCE
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
2
1
3
NOTICE: Never use gasoline, benzine, thinner,
4
alcohol or the like. Discoloration, deformation or
cracks may result.
6
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers, always using Makita replacement parts.
7
8
Fig.13
1. Dust nozzle 2. Joint 3. Dust attachment 4. Nozzle
band 5. Holes in the tool 6. Felt ring 7.Sandingpad
8.Applicationtoolinstallationbolt
1.
Installjoint,dustnozzleanddustattachment.
2.
Install the nozzle band on the tool so that its protrusionsitintheholesinthetooltosecureit.
3. Putthefeltringandthesandingpadonthedust
attachment and then secure them with the application
tool installation bolt.
Toperformcleaneroperation,connectavacuum
cleaner to the tool. Connect a hose of vacuum cleaner
to the dust extraction attachment (optional accessory).
9
ENGLISH
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
speciied in this manual.Theuseofanyother
accessories or attachments might present a risk of
injurytopersons.Onlyuseaccessoryorattachment
for its stated purpose.
If you need any assistance for more details regardingtheseaccessories,askyourlocalMakitaService
Center.
•
Segmentsawblade
•
Roundsawblade
•
Plungecutsawblade
•
Scraper(rigid)
•
Scraper(lexible)
•
Serratedsegblade
•
Generaljointcutter
•
HMremover
•
HMsegsawblade
•
HMsandingplate
•
Diamondsegsawblade
•
Sandingpad
•
Adapter
•
Abrasivepaperdelta(red/white/black)
•
Fleecedelta(medium/coarse/withoutgrit)
•
Polishingfeltdelta
•
Hexwrench
•
Dustextractionattachment
•
Makitagenuinebatteryandcharger
NOTE:Someitemsinthelistmaybeincludedinthe
toolpackageasstandardaccessories.Theymay
differ from country to country.
10
ENGLISH
11
Makita Jan-Baptist Vinkstraat 2, 3070, Belgium
Makita Corporation Anjo, Aichi, Japan
www.makita.com
885495B905
EN
20151217
Download PDF
Similar pages
100mm belt sander
Makita 9920 power sander
Makita 9227CB
Makita GA5034 angle grinder
Finishing Sander
Finishing Sander M9200 INSTRUCTION MANUAL
Finishing Sander
Finishing Sander
Finishing Sander
Bosch 1600A00154