Omega OC90TZ 90cm Ceramic Cooktop User Manual

Ceramic Cooktop
Instruction Manual / Installation Manual
OC90TZ
Congratulations
Enjoy your new ceramic cooktop
Content
1.
2.
3.
4.
5.
6.
7.
8.
Foreword ........................................................................................ 3
1.1 Safety Warnings ......................................................................... 3
1.2 Installation ................................................................................ 3
1.2.1 Electrical Shock Hazard .................................................. 3
1.2.2 Cut Hazard ................................................................... 3
1.2.3 Important safety instructions .......................................... 3
1.3 Operation and maintenance.......................................................... 4
1.3.1 Electrical Shock Hazard .................................................. 4
1.3.2 Health Hazard .............................................................. 4
1.3.3 Hot Surface Hazard ....................................................... 4
1.3.4 Cut Hazard ................................................................... 5
1.3.5 Important safety instructions .......................................... 5
Product Introduction ....................................................................... 7
2.1 Top View ................................................................................... 7
2.2 Control Panel ............................................................................. 7
2.3 Product Information .................................................................... 7
2.4 Working Principle ........................................................................ 7
2.5 Before using your New Ceramic Hob .............................................. 7
2.6 Technical Specification ................................................................. 8
Operation of Product ....................................................................... 8
3.1 Touch Controls ........................................................................... 8
3.2 Choosing the right Cookware ........................................................ 8
3.3 How to use ................................................................................ 9
3.3.1 Start cooking ................................................................ 9
3.3.2 Finish cooking.............................................................. 10
3.3.3 Locking the Controls ..................................................... 10
3.3.4 Using the Double zone function ...................................... 11
3.3.5 Timer control ............................................................... 11
3.3.6 Over-Temperature Protection ......................................... 13
3.3.7 Residual Heat Warning .................................................. 13
3.3.8 Default working times ................................................... 13
Cooking Guidelines ........................................................................ 13
4.1 Cooking Tips ............................................................................. 14
4.1.1 Simmering, cooking rice ................................................ 14
4.1.2 Searing steak .............................................................. 14
4.1.3 For stir-frying .............................................................. 14
Heat Settings ................................................................................ 14
Care and Cleaning ......................................................................... 15
Hints and Tips ............................................................................... 16
Installation ................................................................................... 16
8.1 Selection of installation equipment ............................................... 16
8.2 Before locating the fixing brackets................................................ 17
8.3 Cautions ................................................................................... 18
8.4 Connecting the hob to the mains power supply .............................. 18
1.
1.1
Foreword
Safety Warnings
Your safety is important to us. Please read this information
before using your cooktop.
1.2
Installation
1.2.1 Electrical Shock Hazard
 Disconnect the appliance from the mains electricity supply
before carrying out any cleaning or maintenance on it.
 Connection to a good earth wiring system is essential and
mandatory.
 Alterations to the domestic wiring system must only be
made by a qualified electrician.
 Failure to follow this advice may result in electrical shock or
death.
1.2.2 Cut Hazard
 Take care - panel edges are sharp.
 Failure to use caution could result in injury or cuts.
1.2.3 Important safety instructions
 Read these instructions carefully before installing or using
this appliance.
 No combustible material or products should be placed on
this appliance at any time.
 Please make this information available to the person
responsible for installing the appliance as it could reduce
your installation costs.
 In order to avoid a hazard, this appliance must be installed
according to these instructions for installation.
 This appliance is to be properly installed and earthed only by
a suitably qualified person.
 CAUTION-The cooking process has to be supervised. A short
term cooking process has to be supervised continuously.
3
 This appliance should be connected to a circuit which
incorporates an isolating switch providing full disconnection
from the power supply.
 Failure to install the appliance correctly could invalidate any
warranty or liability claims.
1.3
Operation and maintenance
1.3.1 Electrical Shock Hazard
 Do not cook on a broken or cracked cooktop. If the cooktop
surface should break or crack, switch the appliance off
immediately at the mains power supply (wall switch) and
contact a qualified technician.
 Failure to follow this advice may result in electrical shock or
death.
1.3.2 Health Hazard
 This appliance complies with electromagnetic safety
standards.
 However, persons with cardiac pacemakers or other
electrical implants (such as insulin pumps) must consult with
their doctor or implant manufacturer before using this
appliance to make sure that their implants will not be
affected by the electromagnetic field.
 Failure to follow this advice may result in death.
1.3.3 Hot Surface Hazard
 During use, accessible parts of this appliance will become
hot enough to cause burns.
 Do not let your body, clothing or any item other than
suitable cookware contact the Ceramic glass until the
surface is cool.
 Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot
 Keep children away.
 Handles of saucepans may be hot to touch. Check saucepan
handles do not overhang other cooking zones that are on.
Keep handles out of reach of children.
 Failure to follow this advice could result in burns and scalds.
 Magnetisable metal objects warn on the body can become
hot in the vicinity of the appliance (materials like gold are
not affected).
4
1.3.4 Cut Hazard
 The razor-sharp blade of a cooktop scraper is exposed when
the safety cover is retracted. Use with extreme care and
always store safely and out of reach of children.
 Failure to use caution could result in injury or cuts.
1.3.5 Important safety instructions
 Never leave the appliance unattended when in use. Boilover
causes smoking and greasy spillovers that may ignite.
 Never use your appliance as a work or storage surface.
 Never use your appliance for warming or heating the room.
 After use, always turn off the cooking zones and the cooktop
as described in this manual (i.e. by using the touch controls).
Do not allow children to play with the appliance or sit, stand,
or climb on it.
 Handles of cooking utensils may be hot to touch. Check that
handles do not hang over other cooking zones that are active.
Keep handles out of reach of children. Failure to follow this
advice can result in scalding.
 Do not store items of interest to children in cabinets above
the appliance. Children climbing on the cooktop could be
seriously injured.
 This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience or knowledge, unless they
have been given supervision or instruction concerning the
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
 Do not repair or replace any part of the appliance unless
specifically recommended in the manual. All other servicing
should be done by a qualified technician.
 Do not use a steam cleaner to clean your cooktop.
 Do not place or drop heavy objects on your cooktop.
 Do not stand on your cooktop.
 Do not use pans with jagged edges or drag pans across the
Ceramic glass surface as this can scratch the glass.
 Do not use scourers or any other harsh abrasive cleaning
agents to clean your cooktop, as these can scratch the
5









Ceramic glass.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
This appliance is intended to be used in household and
similar applications such as: -staff kitchen areas in shops,
offices and other working environments; -farm houses; -by
clients in hotels, motels and other residential type
environments; -bed and breakfast type environments.
WARNING: The appliance and its accessible parts become
hot during use.
Care should be taken to avoid touching heating elements.
Cleaning and user maintenance shall not be made by
children without supervision.
WARNING: Unattended cooking on a hob with fat or oil can
be dangerous and may result in fire. NEVER try to extinguish
a fire with water, but switch off the appliance and then cover
flame e.g. with a lid or a fire blanket.
WARNING: Danger of fire: Do not store items on the
cooking surfaces.
Warning: If the surface is cracked, switch off the appliance
to avoid the possibility of electric shock.
The appliance is not intended to be operated by means of an
external timer or separate remote-control system.
Congratulations
on the purchase of your new Ceramic Hob.
We recommend that you spend some time to read this Instruction / Installation Manual in order to fully
understand how to install correctly and operate it. For installation, please read the installation section.
Read all the safety instructions carefully before use and keep this Instruction / Installation Manual for
future reference.
6
2.
Product Introduction
2.1
Top View
1. Max. 1800 W zone
2. Max. 1200 W zone
3. Max. 1100/ 2000W dual zone
4. Max. 1000/ 2200W dual zone
5. Max. 1200 W zone
6. Glass plate
7. Control panel
2.2
Control Panel
1. Heating zone selection controls
2. Power/Timer slider touch control
3. Dual zone control
4. Keylock control
5. ON/OFF control
6. Timer display
2.3
Product Information
The ceramic cooktop uses electric elements under the tempered glass to provide the heat source needed
to cook various dishes. The temperature range can be easily varied to suit your cooking style from high to
moderate and low with ease.
2.4


Before using your New Ceramic Hob
Read this guide, taking special note of the ‘Safety Warnings’ section.
Remove any protective film that may still be on your ceramic hob.
7
2.5
Technical Specification
Cooking Hob
MC-HV848
Cooking Zones
5 Zones
Supply Voltage
220-240V~ 50/60Hz
Installed Electric Power
7600-9200W
Product Size
900x520x55
L×W×H(mm)
Building-in Dimensions A×B (mm)
875x495
Weight and Dimensions are approximate. Because we continually strive to improve our products we may
change specifications and designs without prior notice.
3.
Operation of Product
3.1




Touch Controls
The controls respond to touch, so you don’t need to apply any pressure.
Use the ball of your finger, not its tip.
You will hear a beep each time a touch is registered.
Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth)
covering them. Even a thin film of water may make the controls difficult to operate.
3.2
Choosing the right Cookware
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the
cooking zone. Always centre your pan on the cooking zone.
8
Always lift pans off the ceramic hob – do not slide, or they may scratch the glass.
3.3
How to use
3.3.1 Start cooking
After power on, the buzzer beeps once, all the indicators light up for 1 second then go out, indicating that
the ceramic hob has entered the standby mode.
Touch the ON/OFF
show “-”
control. all the indicators
Place a suitable pan on the cooking zone that you wish to use.
• Make sure the bottom of the pan and the surface of the
cooking zones are clean and dry.
Touching the heating zone selection control, and an indicator
next to the key will flash
Adjust heat setting by touching the slider control.
• If you don’t choose a heat setting within 1 minute, the
ceramic hob will automatically switch off. You will need to
start again at step 1.
• You can modify the heat setting at any time during
cooking.
• You can modify the power level from 0 to 9 by the slide
control.
9
3.3.2 Finish cooking
Touching the heating zone selection control that you wish to
switch off.
Turn the cooking zone off by touching the slider to the lowest
point.
Make sure the display shows ”0”. After cooking an H symbol
will appear to indicate the surface is still hot and will go out
when the surface is cooler.
Turn the whole cooktop off by touching the ON/OFF
control.
Beware of hot surfaces
“H” will show which cooking zone is too hot to touch. It will disappear when the surface has cooled
down to a safe temperature. It can also be used as an energy saving function if you want to heat further
pans, use the hotplate that is still hot.
3.3.3 Locking the Controls


You can lock the controls to prevent unintended use (for example children accidentally turning the
cooking zones on).
When the controls are locked, all the controls except the ON/OFF control are disabled.
To lock the controls
Touch the lock
control
The timer indicator will show “ Lo
“
To unlock the controls
Make sure the ceramic hob is turned on
Touch and hold the lock control
for a while.
When the hob is in the lock mode, all the controls are disabled except the ON/OFF
the ceramic hob off with the ON/OFF
, you can always turn
control in an emergency, but you must unlock the hob first in the
next operation.
10
3.3.4 Using the dual zone function
• This function only works on zones 3# and 4#.
• The dual cooking zone has two cooking areas that you can use a central section and an outer section. You
can use the central section (A) independently or both sections (B) at once.
Zone 3#
Zone 4#
Activate the Dual zone
Press the heating zone selection and then the dual zone control
to activate the dual area (e.g. 6,)
The power level indicator will flash, then press “◎” , after 5
seconds, the indicator stop flash, the dual zone function is
activated, and power level shows “6” and “=” alternately.
Deactivate the Dual zone
Press the heating zone selection control of the dual zone, the
power level indicator will flash.
Press “◎”, and the dual heat zone will be cancelled and power
level returned to “6”.
Note:
1、 The dual zone function is available only in 3# and 4# cooking zones
2、 You can select the function from level 1 to level 9.
3.3.5 Timer control
You can use the timer in two different ways:
a) You can use it as a minute minder. In this case, the timer will not turn any cooking zone off
when the set time is up.
b) You can set it to turn a cooking zone off after the set time is up.
The timer is a maximum of 99 minutes.
11
a) Using the Timer as a Minute Minder
If you are not selecting any cooking zone
Make sure the cooktop is turned on.
Note: you can use the minute minder even if you’re not
selecting any cooking zone.
Touch the timer control, the “10” will show in the timer
display. and the “0” flashes
Set the time by touching the slider control. (e.g. 5)
Touch timer control again, the “1” will flash. To set a
time less than 10 minutes you will need to set the
right number first and then the left number to “0”
Set the time by touching the slider control (e.g.9), now the
timer you set is 95 minutes.
When the time is set, it will begin to count down
immediately. The display will show the remaining time
Buzzer will beep for 30 seconds and the timer indicator
shows “- -” when the setting time finished.
Hint:
a) Touch the “-” or “+” control of the timer once to decrease or increase by 1 minute.
b) Touch and hold the “-” or “+” control of the timer to decrease or increase by 10 minutes.
c) If the setting time exceeds 99 minutes, the timer will automatically return to 0 minute.
b) Setting the timer to turn one cooking zone off
Set one zone
*Touching the heating zone selection control that you
want to set the timer for.
INCREASE OR DECREASE TEMPERATURE OR TIME
TIMER CONTROL/DISPLAY
Touch timer control , the “10” will show in the timer
display and the “0” flashes.
12
Set the time by touching the slider control. (e.g. 5)
Touch timer control again, the “1” will flash. To
set a time less than 10 minutes you will need to
set the right number first and then the left
number to “0”
set the time by touching the slider control (e.g.9), now
the timer you set is 95 minutes.
When the time is set, it will begin to count down
immediately. The display will show the remaining
time
When cooking timer expires, the corresponding
cooking zone will be switched off automatically.
Note:
a) The red dot next to power level indicator will illuminate indicating that zone is selected.
b) You want to change the time after the timer is set, you have to start from step 1.
3.3.6 Over-Temperature Protection
A temperature sensor equipped can monitor the temperature inside the ceramic hob. When an excessive
temperature is monitored, the ceramic hob will stop operation automatically.
3.3.7 Residual Heat Warning
When the hob has been operating for some time, there will be some residual heat. The letter “ H ”appears
to warn you to keep away from it.
3.3.8 Default working times
Another safety feature of the hob is automatic shutdown. This occurs whenever you forget to switch off a
cooking zone. The default shutdown times are shown in the table below:
Power level
Default working timer (hour)
4.
1
8
2
8
3
8
4
4
5
4
6
4
7
2
8
2
9
2
Cooking Guidelines
Take care when frying as the oil and fat heat up very quickly. At extremely high temperatures oil
and fat will ignite spontaneously and this presents a serious fire risk.
13
4.1


Cooking Tips
When food comes to the boil, reduce the power setting as needed to maintain a steady boil.
Using a lid will reduce cooking times on some dishes and save energy by retaining the heat.
4.1.1 Simmering, cooking rice

Simmering occurs below boiling point, at around 85˚C, when bubbles are just rising occasionally to
the surface of the cooking liquid. It is the key to delicious soups and tender stews because the
flavours develop without overcooking the food.
4.1.2 Searing steak
To
1.
2.
3.
4.
cook juicy flavoursome steaks:
Stand the meat at room temperature for about 20 minutes before cooking.
Heat up a heavy-based frying pan.
Brush both sides of the steak with oil.
Turn the steak as required during cooking. The exact cooking time will depend on the thickness of the
steak and how cooked you want it. Times may vary from about 2 – 8 minutes per side. Press the steak
to gauge how cooked it is – the firmer it feels the more ‘well done’ it will be.
5. Leave the steak to rest on a warm plate for a few minutes to allow it to relax and become tender
before serving.
4.1.3 For stir-frying
1. Choose a ceramic compatible flat-based wok or a large frying pan.
2. Have all the ingredients and equipment ready. Stir-frying should be quick. If cooking large quantities,
cook the food in several smaller batches.
3. Preheat the pan and add oil.
4. Cook any meat first, put it aside and keep warm.
5. Stir-fry the vegetables. When they are hot but still crisp return the meat to the pan and add your
sauce.
6. Stir the ingredients gently to make sure they are heated through.
7. Serve immediately.
5.
Heat Settings
The settings below are guidelines only. The exact setting will depend on several factors, including your
cookware and the amount you are cooking. Experiment with the Ceramic hob to find the settings that best
suit you.
Heat setting
1-2
3-4
Suitability
•
•
•
•
•
•
delicate warming for small amounts of food
melting butter, and foods that burn quickly
gentle simmering
slow warming
reheating
rapid simmering
14
5-6
7-8
9
6.
• cooking rice
• pancakes
•
•
•
•
•
•
sautéing
cooking pasta
stir-frying
searing
bringing soup to the boil
boiling water
Care and Cleaning
What?
How?
Important!
Everyday soiling on
glass (fingerprints,
marks, stains left by
food or non-sugary
spillovers on the glass)
1. Make sure the cooktop is off.
2. Apply a cooktop cleaner while
the glass is cool.
3. Rinse and wipe dry with a clean
cloth or paper towel.
4. Switch the power to the cooktop
back on.
• When the power to the cooktop is
switched off, there will be no ‘hot
surface’ indication but the cooking zone
may still be hot! Take extreme care.
• Heavy-duty scourers, some nylon
scourers and harsh/abrasive cleaning
agents may scratch the glass. Always
read the label to check if your cleaner or
scourer is suitable.
• Never leave cleaning residue on the
cooktop: the glass may become stained.
Boilovers, melts, and
hot sugary spills on
the glass
Remove these immediately with a
fish slice, palette knife or razor
blade scraper suitable for Ceramic
glass cooktops, but beware of hot
cooking zone surfaces:
1. Switch the power to the cooktop
off at the wall.
2. Hold the blade or utensil at a 30°
angle and scrape the soiling or
spill to a cool area of the
cooktop.
3. Clean the soiling or spill up with
a dish cloth or paper towel.
4. Follow steps 2 to 4 for ‘Everyday
soiling on glass’ above.
• Remove stains left by melts and
sugary food or spillovers as soon
as possible. If left to cool on the
glass, they may be difficult to
remove or even permanently
damage the glass surface.
• Cut hazard: when the safety cover
is retracted, the blade in a scraper
is razor-sharp. Use with extreme
care and always store safely and
out of reach of children.
Spillovers on the
touch controls
1. Switch the power to the cooktop
off.
2. Soak up the spill
3. Wipe the touch control area with
a clean damp sponge or cloth.
4. Wipe the area completely dry
with a paper towel.
5. Switch the power to the cooktop
back on.
• The cooktop may beep and turn
itself off, and the touch controls
may not function while there is
liquid on them. Make sure you wipe the
touch control area dry before turning the
cooktop back on.
15
7.
Hints and Tips
Problem
Possible causes
The cooktop cannot
Be turned on.
No power.
The touch controls are
unresponsive.
The controls are locked.
The touch controls are
difficult to operate.
There may be a slight film of
water over the controls or you
may be using the tip of your
finger when touching the
controls.
Rough-edged cookware.
The glass is being
scratched.
Some pans make
crackling or clicking
noises.
Unsuitable, abrasive scourer or
cleaning products being used.
This may be caused by the
construction of your cookware
(layers of different metals
vibrating differently).
What to do
Make sure the ceramic hob is
connected to the power supply
and that it is switched on.
Check whether there is a power
outage in your home or area. If
you’ve checked everything and the
problem persists, call a qualified
technician.
Unlock the controls. See section
‘Using your ceramic cooktop’ for
instructions.
Make sure the touch control area is dry
and use the ball of your finger when
touching the controls.
Use cookware with flat and smooth
bases. See ‘Choosing the right
cookware’.
See ‘Care and cleaning’.
This is normal for cookware and
does not indicate a fault.
8. Installation
8.1
Selection of installation equipment
Cut out the work surface according to the sizes shown in the drawing.
For the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole.
Be sure the thickness of the work surface is at least 30mm. Please select heat-resistant work surface
material to avoid larger deformation caused by the heat radiation from the hotplate. As shown below:
16
L(mm)
W(mm)
H(mm)
D(mm)
A(mm)
B(mm)
X(mm)
900
520
55
51
875+4
495+4
50 mini
+1
+1
Under any circumstances, make sure the ceramic cooker hob is well ventilated and the air inlet and outlet
are not blocked. Ensure the ceramic cooker hob is in good work state. As shown below
Note: The safety distance between the hotplate and the cupboard above the hotplate should be at
least 760mm.
A(mm)
B(mm)
C(mm)
D
E
650mm
50 mini
20 mini
Air intake
Air exit
8.2
Before locating the fixing brackets
5mm
The unit should be placed on a stable, smooth surface (use the packaging). Do not apply force onto the
controls protruding from the hob.
Fix the hob on the work surface by screw four brackets on the bottom of hob (see picture) after
installation.
A
B
C
D
screw
bracket
Screw hole
base
Adjust the bracket position to suit for different work surface’s thickness.
17
8.3
Cautions
1. The ceramic cooker hob must be installed by qualified personnel or technicians. We have professionals
at your service. Please never conduct the operation by yourself.
2. The ceramic cooker hob shall not be mounted to cooling equipment, dishwashers and rotary dryers.
3. The ceramic cooker hob shall be installed such that better heat radiation can be ensured to enhance its
reliability.
4. The wall and induced heating zone above the work surface shall withstand heat.
5. To avoid any damage, the sandwich layer and adhesive must be resistant to heat.
6. A steam cleaner is not to be used.
8.4
Connecting the hob to the mains power supply
The power supply should be connected in compliance with the relevant standard, or a single-pole circuit
breaker. The method of connection is shown below.
1. If the cable is damaged or needs replacing, this should be done by an after-sales technician using the
proper tools, so as to avoid any accidents.
2. If the appliance is being connected directly to the mains supply, an all-pole circuit breaker must be
installed with a minimum gap of 3mm between the contacts.
3. The installer must ensure that the correct electrical connection has been made and that it complies with
safety regulations.
4. The cable must not be bent or compressed.
5. The cable must be checked regularly and only replaced by a properly qualified person.
6. The installer must to use the H05GG-F power cord.
18
This appliance is labelled in compliance with European directive 2012/19/EU for Waste
Electrical and Electronic Equipment (WEEE). By ensuring that this appliance is disposed
of correctly, you will help prevent any possible damage to the environment and to human
health, which might otherwise be caused if it were disposed of in the
wrong way.
The symbol on the product indicates that it may not be treated as normal household
waste. It should be taken to a collection point for the recycling of electrical and electronic
goods.
DISPOSAL: Do not
dispose this product
as unsorted municipal
waste. Collection of
such waste separately
for special treatment is
necessary.
This appliance requires specialist waste disposal. For further information regarding the
treatment, recover and recycling of this product please contact your local council, your
household waste disposal service, or the shop where you purchased it.
For more detailed information about treatment, recovery and recycling of this product,
please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
19
AUSTRALIAN & NEW ZEALAND PRODUCT WARRANTY
AUSTRALIAN CUSTOMERS
STATEMENT OF STANDARD WARRANTY CONDITIONS
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
NEW ZEALAND CUSTOMERS
Nothing herein contained shall be construed in any way as excluding or limiting your rights under the Consumer Guarantee Act
1993.
OUR WARRANTY
This product is also covered by the manufacturer's warranty set out in this document (Our Warranty).
Our Warranty is for a period of twenty four (24) months from the date of purchase and for refrigeration appliances will have an
additional thirty six (36) months after the first twenty four (24) months on the Sealed System (PARTS only) Compressor &
condenser etc. The labour cost to replace these parts is the responsibility of the customer.
This is in addition to (and does not exclude, restrict or modify) any rights or remedies to which you may already be entitled to under
the Australian consumer law or the New Zealand Consumer Guarantee act 1993 relating to this product.
Our warranty (which is subject to the conditions below) covers rectification free of charge of any fault arising from defective
materials or components, or faulty workmanship. The product will be repaired or replaced at the option of Omega, and all costs of
installation, removal, cartage, freight travelling and insurance are to be paid by the customer.
Our warranty is subject to the following conditions:
1. That the purchaser contact Omega prior to any product repair.
2. That the purchaser carefully follows all instructions provided with the product and complies with all relevant electrical &
plumbing regulations in their State when installing the product.
3. That the purchaser carefully follows the instructions provided in the owner’s handbook relating to the proper use and care of
the product and does not use the product for any purpose other than the DOMESTIC use for which it has been designed. If
the appliance is used in commercial applications or for rental purposes, Our Warranty is limited to a warranty of Twelve (12)
months covering all parts with Three (3) months on any labour cost of service or repair.
SERVICE AREA
The provision of service under Our Warranty is limited by the boundary / territory area of the nearest service centre. Travelling
cost incurred for service outside this area is not covered by Our Warranty and service will incur commercial cost to be paid by the
customer regulated by the number of kilometres travelled beyond the service area. These costs will be disclosed to you for
acceptance by you prior to your claim being processed.
Microwave ovens must be returned to your nearest Authorised Service Centre for repair as they are a carry in serviceable
appliance.
WHAT IS COVERED: By Our Warranty
During the warranty period, Omega or its authorised Service Centre will, at no extra charge, if your appliance is readily accessible
without the need of special equipment and subject to the terms and conditions of this warranty, repair or replace any parts which it
considers defective.
WHAT IS NOT COVERED: By Our Warranty
1. Products installed damaged or incomplete or not in compliance with the relevant electrical & plumbing regulations in their
State.
Normal wear and tear e.g. cleaning, light globes, filters etc.
Failure resulting from power surges and electrical storms.
Insect or vermin infestation.
Unauthorised repairs or use of non- genuine Omega parts.
Any failure caused by the product not being used in accordance with the instruction and the installation manual provided with
the product.
7. Misuse or abuse, including failure to properly maintain or service.
8. The clearing of blockages in pumps and hoses.
9. Damage which occurs during delivery or installation.
10. Claims to product surface coating due to liquid or solid spill-overs, accidental damage or damage caused from cleaning
products not recommended by Omega.
2.
3.
4.
5.
6.
HOW TO CLAIM OUR WARRANTY
You will need to contact Omega in Australia or New Zealand by using the contact details below.
IN AUSTRALIA
IN NEW ZEALAND
Omega is a division of Shriro Australia Pty Ltd
Omega is a division of Monaco Corporation
ABN 28 002 386 129
(Member of Shriro Australia Pty Ltd)
Locked Bag 5002, Kingsgrove, NSW, 2208
PO Box 4399, Shortland St, Auckland, 1140
Phone: 1300 795 572 Fax: 1800 686 413
Phone: 09 415 6000 Fax: 09 415 7060
Email: customercare@shriro.com.au
Email: service@shriro.com.au
Web: www.omegaappliances.com.au
Note: Please complete the following details when you have unpacked the product:
Model No…………………………………………
Serial No………………………………………
Date of Purchase……………………………..…
Retailer……………………………………….…
20
Download PDF
Similar pages
• 80 cm width Black ceramic glass with stainless steel flush-fitted
LG LCG3091ST User's Manual
Miele 3-Burner Specification Sheet
Neff C47D42S0
Franke 0390070
CDA HG6320
Installation guide