RELAY DRIVEN ALTERNATING ELECTRONIC FLASHER
w/ 100% SOLID STATE DAYTIME RUNNING LIGHTS
(ETxxDRL)
Congratulations! You are now the proud owner of the most
technically advanced, Relay Driven Alternating Headlight
Flasher with Daytime Running function in the market today.
Add to it our commitment to quality, this new flasher system
will provide you with years of dependable trouble-free service.
HIGH BEAM
BLUE
TO
DIMMER
SWITCH
NOTE
FUSE
FUSE
WHITE
ORANGE
A properly installed DRL Flasher will alternate the vehicle's
high beam headlights. When used at night, the low beam head
lights remain on for proper illumination while the high beams
flash to gain attention and increase the vehicle's visibility. When
the dimmer switch is activated to "high beam", the flasher
system "High Beam Override" interrupts the flasher sequence
to allow for normal high beam function. Flashing automatically resumes when dimmer switch is deactivated. Any time
the flasher or either high or low beam headlights are OFF, the
DRL function will turn the high beam headlights on at 1/2 brightness.
NOTE
Flashing Headlight and Taillight Systems are intended
for use on approved vehicles ONLY. It is the
responsibility of the user of these systems to insure
compliance to any Federal, State or Municipal
regulations which may apply.
TO SIDE
MARKER
LIGHTS
ROAD RUNNER/
POWER PULSE
WHITE/RED
ORANGE
GREY
DRL
OVERRIDE
(OPTIONAL)
IGNITION
WIRE
BLACK
RED
TO
BATTERY
PLUS
PINK
This Flasher will not work on any ground side switched
system. If you have any questions regarding what
type of system your vehicle has, contact SoundOff
Signal's Technical Support Department at 1-800-3387337.
YELLOW
CUT
GREEN
DO NOT USE THIS FLASHER ON VEHICLES THAT HAVE
4-HIGH BEAM HEADLIGHT SYSTEMS !
LOW BEAM
MULTI
PATTERN
FLASHER
ON/OFF
Wiring Diagram
BLUE & YELLOW WIRE: Locate the wire that supplies power
to the passenger side high beam headlights. Cut this wire
approximately 10" to 12" from the back of the headlight. Connect the yellow wire to the lead that returns to the passenger
side high beam. Connect the blue wire to the other piece of
cut wire. This will make the driver's side high beam flash.
NOTE
INSTALLATION
Maximum total high beam output is 110 watts. DO
NOT use with a four sealed beam headlight system.
MOUNTING: Mount the flasher so that the maximum amount
of air will flow across it, typically in the front passenger side of
the engine compartment.
GRAY WIRE: "T" or tap into the vehicle's low beam headlight
wire.
GREEN WIRE: Connect to a convenient, reliable ground.
NOTE
ALWAYS CONNECT THE GREEN WIRE FIRST
WHEN INSTALLING AND DISCONNECT LAST
WHEN REMOVING.
BLACK WIRE (OPTIONAL): If an "Automatic Night Time
Flasher Cutoff" is required, simply "T" or tap the black wire
into the flasher's grey wire. If not required, connect to ground.
RED WIRE: Connect to a powered switch. Only a 1/4 amp is
required to operate the flasher. When the red wire is activated, the flasher will go into a three pattern, continuously
cycled mode (multi-pattern). When the red wire is NOT powered, the flasher defaults to normal alternator mode
WHITE/RED WIRE: "T" or tap into the vehicle's wire that
becomes "hot" when the vehicle is started, and "cold" when
the vehicle is turned off.
PINK WIRE (OPTIONAL): Connect to the "hot" side of a user
supplied switch, the park brake or neutral safety switch. When
the pink wire is grounded through one of the switches, the
DRL function and marker lights will be deactivated.
ORANGE WIRE: Either orange wire "T" or tap into the vehicle's
side marker light circuit hot wire.
ORANGE WIRE (other): connect through a 20 amp fuse directly to the positive post of the battery.
WARRANTY
SoundOff Signal warranties the ETRRDRL, ETPPDRL and
ETQSDRL Relay Driven Electronic Flasher Systems for one (1)
full year from the date of purchase to the original purchaser against
any manufacturer defects or workmanship. This warranty applies
only to units installed according to manufacturer's installation instructions and operated within the units specifications.
SoundOff Signal's obligation under this warranty is limited to repairing or exchanging the unit.
Warranty is void if the unit was installed incorrectly or maliciously
damaged.
All warranty claims must be accompanied by a dated proof of
purchase.
SoundOff Signal retains the right to be the sole mediator of what
constitutes defects in performance or manufacturing.
Covered by U.S. Patent #'s 4114071 & 4309639
NOTE
DO NOT USE A CIRCUIT BREAKER OF FUSIBLE
LINK. ATO FUSE IS RECOMMENDED.
WHITE WIRE: Connect through an ATO type fuse (20 amp)
to the positive post of the battery. DO NOT USE A CIRCUIT
BREAKER, FUSIBLE LINK OR SLOW BLOW TYPE FUSE.
ETxxDRL 3/05