FLIR/Digimerge DNR200V Series Quick Connection Guide

Thermal Mini Bullet Camera
Quick Connection Guide
PACKAGE CONTENTS:
1
A
B
1 x IP Bullet Camera
1 x Mounting Template
4 x Drywall Anchors
4 x Mounting Screws
2 x Allen Set Screws
C
D
Installing the Camera
Use the included mounting template to mark holes
for the screws.
2
A
Adjusting the Camera
1 x RJ45 Waterproof Cap
Quick Start Guides
1
A
NOTE: Use the included drywall anchors if installing
into drywall.
Connect cables as shown in the section “Connecting
the Camera”.
Mount the camera to the surface using the included
mounting screws (4x).
Allen set screws (2x)
B
Adjustment screw
Mounting screws (4x)
Mounting template
B
Use a Phillips head screwdriver (not included) to
loosen the adjustment screw on the camera stand.
C
Move the camera to the desired position. Tighten the
adjustment screw when finished.
D
Tighten the Allen set screws with the included Allen
key.
C
Weights & Dimensions
Latest software and manuals available on
•
•
6.8” /
173mm
3.1” / 78mm
•
•
2.8” /
72mm
Fo r s u p p o r t , vi s i t
www.flir.com/security/support
Weight
0.95lbs / 0.43kg
2
3
12V DC Power Input Polarity
IP / PoE
1. Ethernet Port: Connect the camera to a FLIR NVR or a router or switch
on your network using Cat5e or better Ethernet cable (not included). PoE
Class 3 supported.
2. Power Input: Connect a 12V DC power source if you are not using PoE.
3. Video Out (BNC): Analog video ouput to a test monitor (optional).
MPX
1. Ethernet Port: Install the MPX Terminator.
When you power up the camera with the
MPX Terminator installed, the camera operates as an MPX camera.
2. Power Input: Connect a 12V DC power source (300mA or higher).
3. Video Out (BNC): Connect the camera to a FLIR MPX DVR. Video and
MPX camera control are supported over a standard coaxial cable.
Analog
1. Ethernet Port: Not used.
2. Power Input: Connect a 12V DC power source (300mA or higher).
3. Video Out (BNC): Connect the camera to an analog DVR.
Safety Precautions
•
Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2015 FLIR Systems, Inc. All rights reserved.
Connecting the Camera
Drill holes for the mounting screws.
1 x MPX Terminator
www.flir.com/security/support
3
Insert the included Allen set screws (2x).
Drywall anchors (4x)
1 x Allen Key
T4325BN / T4350BN
T4325BNP / T4350BNP
•
Use an appropriate low voltage power cable to prevent fire or electrical shock.
Make sure to install the camera in an area that can support the camera
weight.
There are no user serviceable parts inside the camera. Please do not
disassemble the camera.
Be careful not to leave fingerprints on the camera’s infared optics. Clean only
with low pressure fresh water and a lens cloth.
Camera is rated for outdoor use (IP66), but is not intended for submersion in
water.
If using DC power, make sure to follow the correct polarity as marked on the
power cable.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
T4325BN_T4350BN_SERIES_QCG_EN_R2