Gold Standard Brushless Loader - DRI

Gold Standard Brushless Loader
GSL Series: 12 and 19 lb. ( 5.4 and 8.6 kg.) Capacity Based on PC Pellets @ 38 lb/ft3
The GSL Series Loader* with standard
brushless motor, pendant control and
pivot access, boasts a 5-Year Warranty…
As brushes wear, the commutator wears creating an
increasing gap where dust contamination and motor
failure occurs. These factors cause brushes to wear
down faster and faster with each change, leading to
added maintenance and downtime.
Motor manufacturers recommend discarding vacuum
loader motors after three brush sets.
Maintenance-free Brushless
Motors Last 4 Times As Long
As Motors With Brushes
Long-life motor and no brush
changes eliminate maintenance
and downtime.
Double Pivot Access
Loader operates in upright
position then pivots and locks
in place for easy access.
Full-featured, Standard
Plug-In Pendant Control
Full-featured control is
mounted on loader. A 12’
cable (standard) puts control
at your fingertips, so changing
loader parameters is easy.
GSL-12 and -19
Patent Pending MicroBurst
Keeps Filters Clean
High intensity MicroBurst
blowback air, blasts the whole
filter area to remove dust and
fines ensuring that the dump
throat is clear for proper sealing.
SureSeal Flapper Valve
Avoids Loading Failures
Reliable SS seal surfaces stay
aligned and resist wear, while
MicroBurst air blast removes
residual dust for a tight seal.
GSL-19
Open
*Patent # 8,753,432
Plus:
• 115V/1ph/50-60 Hz operation
• 15 ft. (4.6 m) length of flex
hose, lance and hose clamps
• Dual reinforced polyester disc filter media
• All material contact points are non-ferrous
• Dump Valve with integrated demand level switch on
standard models
• Conveying rate up to 1000 lb./hr.
• 5-Year warranty
PROUDLY MADE IN THE USA
Gold Standard Brushless Loader
Application
Brushless Vacuum Motor Lasts 4X Longer with No Brush Changes!
GSL
BRUSHLESS
Vacuum Motor
Conventional
BRUSH type
Vacuum Motor
5000 HR Runtime - 5 Year Warranty
$$$
1250 HR
3 Brush Sets
1250 HR
3 Brush Sets
$$$
1250 HR
3 Brush Sets
$$$
1250 HR
3 Brush Sets
No Warranty
Upright Operating Position
Brushless Vacuum Motor for
Long-Life and
Reduced Maintenance
Isolated Exhaust Air Protects
Motor From Plastic Fines
Adjustable Inlet Position for
Convenient Installation
Removable Control Pendant
for Remote Operation
Modular Construction for
Easy Installation
Discharge Shroud
Protects Dump Throat
GSL-19 Loader
15’ Flex Hose with
Clamps
Control Pendant can
be Loader or Remote
Mounted (12’ Pendant
Included)
Pick-up Wand
Magnetic Backed
Control Pendant
Mounts on Hopper
and other Metal
Surfaces Convenient
to the Operator
Full-featured control includes load
time, no-load alarm, alarm light,
silencer, proportioning and purging.”
Pivot Position for Easy Access
Hinge Design Holds
Lid Open For Cleaning
MicroBurst
Blowback
Loader pivots forward from
operating position and captive detent pin locks loader
in place during operation.
Lid pivots back and locks in
place for easy access.
Stainless Steel Body
Locking Base
Cast Aluminum
Cone/Pivot Stop
Specifications:
Model
Motor
amps/hp
Discharge
Diameter
A
B
C
D
1.5
14/1.3
3
37.11
31.01
14.76
19.58
1.5
14/1.3
3
33.24
28.88
14.76
17.57
Capacity* Inlet O.D.
GSL-19
19 lb.
GSL-12
12 lb.
*Based on PC pellets @ 38 lb./ft
3
**Pivoting and opening top requires 6” ( 15.2 cm) for clearance on GSL-19.
† Recommended throughput: GSL-19 = up to 1000 lb./hr. (450 kg/hr) GSL-12 = up to 650 lb./hr. (295 kg/hr)
† Recommended throughput/hr. based on free flowing virgin pellets through 15’ of flex hose.
Exceeding recommended throughputs may result in shortened motor and filter life however,
increased throughputs are possible depending on resin and equivalent feet calculation.
Generally, a central conveying system should be used for higher throughputs.
Maximum conveying distance in addition to 15’ hose, can include 30’ of horizontal tubing
and 1 elbow. Additional vertical travel, bends or flex hose will reduce recommended throughput.
Accessories: (Show as separate line item on order - See price list #302.)
56.60°
Replacement Plug-N-Play Control Pendant with 12 ft. cable:
(One included with each GSL)
A
Replacement 12 ft. cable
External Proportioning Valve:
(Includes coupler, wand, hose and clamps.) 1.5”and 2.0” O.D.
Level Switch, Capacitance, 30mm dia., 2m cable
Capacitance Level Switch
in lieu of Photo-eye Sensor (for GSL-MM models)
30°
Options:
D
2” Inlet: (in lieu of 1.5”)
Extended Wear Package: Recommended when loading
abrasive materials - contact factory
Alternate Glass Size: 12 lb. Glass (Adds 4” to Height) or
16 lb. Glass (Adds 7” to Height)
Retro-fit Kit to convert GSL-19 into GSL-19-MM:
Kit includes glass, twist-lock plug and photo-eye
GSL-19 mounted on
machine hopper MHA-19
(See separate data sheet)
B
5.16”
C
10.38” O.D.
*48.35”
*42.75”
9.00” Dia.
Bolt Hole Circle
14.22”
GSL-19 & -12MM
Flange Dimensions
6” x 6”
GSL-19-MM Dimensions
*Deduct 4” for GSL-12-MM
Machine Mount Models includes 8 lb. JIT Glass Hopper with height adjustable photo eye
demand switch.
© 2018 DRI-AIR Industries
All rights reserved All information in this
bulletin is subject to change without notice.
16 Thompson Road, PO Box 1020, East Windsor, CT 06088-1020
T: 860.627.5110 F: 860.623.4477
.3125” Dia.
Typ. (4 places)
Mounting Flexibility
Standard mounting hole pattern
plus adapter ring allows GSL to
replace most competitive models.
E: sales@dri-air.com
www.dri-air.com
Form # GSLDA 05 JAN 2018