FTD100Micro
Microtype 8-bit Digital 1-ch Video
Features
Video

NTSC or PAL video standards supported
Non-compressed 8-bit digitally encoded video
No video degradation over the maximum operating distance
Optical




One fiber design
High performance laser-based optics
Multimode or Singlemode
ST or FC connectors available
Robust Design



Plug-and-Play design, no in-field adjustments required
Wide operating temperature range of -40ºC to +75ºC
Designed for use in harsh environments
Local and remote diagnostics

Description
The FTD100Micro Series offers 8-bit PCM digital video
transmission with no video degradation over the entire
operating distance (up to 20km) and a small, but mighty
design that fits into most CCTV camera housings.
Service-friendly LED status indicators on front of the module
Warranty

Comprehensive Lifetime Warranty
The cost-effective unit features high-performance laserbased optics for the clearest, most reliable data
transmission over one fiber in both single and multi-mode.
This plug-and-play product provides instant product
compatibility for most major security manufacturers'
equipment and reliability in harsh environments.
These units are compatible with the FTD100
transmitters/receivers and FTD100-XXR3 receivers.
Typical Application
FTD100Micro-SSR
FTD100Micro-SST
1 Fiber
Video
Video
www.ot-systems.com
1
Video Transmission


FTD100Micro
Specifications
LED
Video
Number of Channels
1
Video Signal Indication (Presence)
Green LED lit
Format
NTSC/PAL
Optical Carrier Detected
Yellow / Active
Input/Output
1 Volt pk-pk (75 ohms)
Power
Red / On
Bandwidth
>=6MHz
Differential Gain
<1% Typical
Differential Phase
<1 Degree Typical
SNR-CCIR weighted
>60dB
Connectors
Video Input / Output
BNC
Optical Input / Output
ST (standard), FC (optional)
Power
2-pin screw terminal
Electrical and Mechanical
Power
12VDC(24VAC*)@1.8W / From MR-C10
Dimensions(WxHxD)
36.2 x 24.5 x 101(118*)mm(Max)
Shipping Weight
0.1kg
Operating Temp
-40°C to +75°C
Storage Temp
-40°C to +85°C
Relative Humidity
0 to 95% non-condensing
MTBF
> 100,000 hours
Video Transmission
Environmental
* Specifications of FTD100Micro24 Models
Ordering Information
Fiber Type
Multi-mode
(62.5/125μm)
Single-mode
(9/125μm)
Options
Description
Part Number
FTD100Micro-SMT
Microtype 1-ch Video Transmitter
FTD100Micro24-SMT
Microtype 1-ch Video Transmitter(24VAC)
FTD100Micro-SMR
Microtype 1-ch Video Receiver
FTD100Micro-SST
Microtype 1-ch Video Transmitter
FTD100Micro24-SST
Microtype 1-ch Video Transmitter(24VAC)
FTD100Micro-SSR
Microtype 1-ch Video Receiver
Max.
Distance
(Km)
No.
of
slots
23
4
NA
17
20
NA
Wavelengths
(nm)
Optical Power
Budget
(dB)
1310
1310
 ST type connector is standard. For FC type, specify “F” in the suffix. E.g. FMT.
 Please feel free to consult factory if longer transmission distance is required.
Power Adaptor
 Power adaptor is included.
Rack Mount Chassis
 MR-C10 is to be purchased separately. Please refer to accessories section for details.
Notes:
 Transmission distance will suffer if additional losses are introduced by the optical connectors, fusions, splices and the fibers within the
network.
 Operating distance of multimode is limited by the characteristics of the fiber bandwidth.
 Power adaptor is manufactured by third party and is supplied with fitted screw - terminal output cables.
 Please feel free to consult factory for any special requirement and customization.
ISO 9001:2000
FM 88638
OT Systems Ltd., November 2013
Due to continuous improvement, all product specifications are subject to change without further notice.
www.ot-systems.com
2