Features Product Description Functional Description

 AA1403015-E6-A
SFP+, 10GBASE-SR 10G Ethernet Module
850mn, 300m, MMF, LC RoHS6
AA1403015-E6-A
10Gbase SFP+ Transceiver
Features
•
•
•
•
•
•
•
•
•
Compliant to SFP+ Electrical MSA SFF-8431
Compliant to SFP+ Mechanical MSA SFF-8432
Multi-rate compliance for Ethernet and Fiber Channel
Transmission distance up to 300m (OM3 fiber)
Sub watt power consumption: 0.65W (typ.)
0°C to +70°C case operating temperature range
Laser Class 1 IEC / CDRH compliant
RoHS 6/6 compliant
Compliant with product safety standards
Product Description
The AA1403015-E6-A is a multipurpose multi-rate optical transceiver module for transmission
at 850nm over multimode fiber. Supporting Ethernet and Fiber Channel standards make it
ideally suited for 10G data communication and storage area network applications. Its sub
watt power consumption and its excellent EMI performance allow system design with high
port density. The small form factor integrates an 850nm vertical cavity surface emitting laser
(VCSEL) in an LC package and a PIN receiver. Approved Networks Computer
Peripheral’s module is lead free, RoHS compliant and is designed and tested in accordance
with industry safety standards.
Functional Description
The Transceivers convert information from electrical to optical format, and back again, at
different data rates depending upon the chosen standard. The transmit path consists of
an AC coupled 100 ohm differentially terminated driver coupled to a highly reliable
850nm VCSEL. The laser output may be disabled by pulling the TX_DISABLE line high.
The laser is also disabled if this line is left floating, as it is pulled high inside the
transceiver. The SFP+ MSA (Multiple Source Agreement) defines two RATE_SELECT
lines, one for the transmitter (pin 9) and one for the receiver (pin 7). Depending upon the
transceiver application, the transmitter RATE_SELECT line can switch between1 GBd
and 10 GBd.
The receiver path consists of a ROSA (receiver optical sub-assembly) for optical
electrical conversion, followed by a limiting amplifier to boost the electrical signal. A
LOSS_OF_SIGNAL (LOS) status line is provided to facilitate easy link detection.
Depending upon the transceiver application, optimum receiver bandwidth may be
configured using the receiver RATE_SELECT pin: for Ethernet applications to switch
between 1 GBd and 10 GBd data rates, and for Fiber Channel applications switch ≤/> 4
GBd data rates.
Approved Networks, Inc.
www.ApprovedOptics.com
Page 1 of 8
AA1403015-E6-A
SFP+, 10GBASE-SR 10G Ethernet Module
850mn, 300m, MMF, LC RoHS6
Electrical Characteristics Absolute
Maximum Ratings
Rating
Conditions
Symbol
Min
Max
Units
Storage Ambient Temperature Range
Jstg
-40
+85
°C
Powered Case Temperature Range
Jc
0
+75
°C
RH
0
95
%
-0.5
3.6
V
4.0
V
Operating Relative Humidity
Non condensing
Supply Voltage Range @ 3.3V
VCC3
Open Drain VCC Level
VOD
HBM human body model per JEDEC
1
JESD22-A114-B
Static Discharge Voltage excluding
HBM human body 2
High Speed Pins
model
EN61000-4-2
Criterion B: Air
Static Discharge Voltage Module on
15
Discharge Direct
SFP+
8
Contact discharge
Any stress beyond the maximum ratings may result in permanent damage to the device.
Specifications are guaranteed only under recommended operating conditions.
Static Discharge Voltage Speed Pins
on High
Approved Networks, Inc.
www.ApprovedOptics.com
Page 2 of 8
kV
kV
kV
AA1403015-E6-A
SFP+, 10GBASE-SR 10G Ethernet Module
850mn, 300m, MMF, LC RoHS6
Recommended Operating Conditions
Parameter
Conditions
Symbol
Min.
Operating Case Temperature
altitude of < 3km
JCase
0
Typical
Power Supply Voltage@3.3V
Vcc3
3.135
DC Common Mode Voltage
Vcm
0
3.30
Max.
Unit
+70
°C
3.465
V
3.6
V
Low Speed Characteristics
Parameter
Conditions
Supply Current Transmitter
Supply Current Receiver
Power Consumption
@ VCCTX
@ VCCRX
TX_Fault, RX_LOS
TX_Dis, RS0, RS1
Host Vcc Range
2V – 3.47V
Symb
ol
IVCCT X
IVCC RX
VOL
Low Voltage TTL
SCL, SDA
Host Vcc Range
3.14V – 3.47V
VIH
VIL
Typ
Max
Unit
s
120
0.65
mA
1
0.4
Host_ Vcc
+0.3
0.8
VccT +0.3
-0.3
mA
125
0
Host_ Vcc – 0.5
VIL
VOH
Min
W
V
2.0
-0.3
VccT*0.3
VIH
VccT*0.7
VccT +0.5
VOL
0.0
0.4
VOH
Host_ Vcc – 0.5
Host_ Vcc +0.3
SFI Module Transmitter Input Characteristics
Parameter
Supported Data Rate
Reference Differential Input
Impedance
Input AC Common Mode
Input Voltage
Approved Networks, Inc.
Conditions
Symbol
Min
www.ApprovedOptics.com
Typ
Max
10.3125
11.3
100
Page 3 of 8
Units
Gbd
Ω
mV
(RMS)
AA1403015-E6-A
SFP+, 10GBASE-SR 10G Ethernet Module
850mn, 300m, MMF, LC RoHS6
Differential Input Voltage
Swing
0.01 –
Differential Input Sparameter
Differential to Common
Mode Conversion 2)
Total Jitter
Data Dependant Jitter
Uncorrelated Jitter
VID
3.9GHz
3.9 –
Eye Mask
11.1GHz
SDD11
150
1)
-10
1)
TJ
DDJ
11.1Ghz
See SFP+ MSA
900
SCD11
0.01 –
mV
dB
dB
-10
dB
0.28
UI(p-p)
0.1
UI(p-p)
UJ
0.023
RMS
X1
0.14
UI
0.35
UI
X2
SFI Module Receiver Output Characteristics
Parameter
Conditions
Symbol
Reference Differential
Output Impedance
Termination Mismatch
Supported Data Rate
Output AC Common Mode
Output Voltage
Differential Output Amplitude
RLoad=100Ohm ,
Differential
Typ
Max
1
10.312
5
11.3
Zd
Δ Zd
Min
100
VOSPP
350
650
Ω
5
%
15
mV
(RMS)
800
mV
35
ps
-10
dB
1)
dB
-7
dB
6.5 – 11.1Ghz
-3
1) Return Loss given by equation Sxx22(dB) = -8+13.33 Log10(f/5.5), with f in GHz;
2) Common mode reference impedance is 25Ω. Common mode return loss helps absorb
dB
Output Rise and Fall time
Differential Input Sparameter
Common Mode Output
Return Loss2)
20% to 80%
0.01 – 3.9GHz
tRH, tFH
3.9 – 11.1GHz
0.01 – 6.5Ghz
SDD22
SCC22
24
reflection and noise improving EMI.
Gbd
Units
Approved Networks, Inc.
www.ApprovedOptics.com
Page 4 of 8
AA1403015-E6-A
SFP+, 10GBASE-SR 10G Ethernet Module
850mn, 300m, MMF, LC RoHS6
Optical Characteristics General Parameters
Parameter
Operating
Range
Bandwidth
Min Modal
(MHz*km)
Conditions
62.5 µm MMF
50 µm MMF
62.5 µm MMF
50 µm MMF
50 µm MMF
160
400
200
500
2000
Optical Transmitter
Parameter Optical
Transmitter
Nominal Wavelength
Conditions
Ethernet version
Fiber Channel version Average Launch
Power
Ethernet version
Extinction Ratio
Typical
1GBd
lOP
2
2
0.5
0.5
0.5
220
500
275
550
X
Fiber Channel version Average Launch
Power
Min
Spectral Width
Symbol
Typ
Max
λΤΡΠ
840
850
860
Pavg
POMA
ER
Ethernet 1.25GBd
Relative Intensity
Noise
Min
RIN
0.65
m
Units
nm
0.45
-7.3
-5.2
-4.3
3.5
tbd
Units
26
66
33
82
300
Symbol
Δλ
Typical
10GBd
-1
dBm
dB
-128
dB/Hz
Optical Receiver
Parameter
Maximum Input
Power
Conditions
Symbol
Center Wavelength Receiver Sensitivity
Ethernet
Receiver Sensitivity
Fiber Channel
Pavg, PRBS 2 -1, BER
< 1*10-12@ 1.25GBd *)
OMA, PRBS 231-1, BER < 1*1012@10.3125GBd
OMA, PRBS 231-1, BER < 1*10-12@2GBd
OMA, PRBS 231-1, BER < 1*10-12@4GBd
OMA, PRBS 231-1, BER
< 1*10-12@8GBd
Approved Networks, Inc.
840
PIN
850
-1
Units
860
-13.0 -12.0 tbd
-11.1
-11.2
www.ApprovedOptics.com
Page 5 of 8
dBm
nm
PIN
Max
Typ
λΧ
31
PMAX
Min
dBm
dBm
AA1403015-E6-A
SFP+, 10GBASE-SR 10G Ethernet Module
850mn, 300m, MMF, LC RoHS6
OMA, PRBS 231-1, BER
< 1*10-12@10GBd
OMA, PRBS 231-1, BER
< 1*10-12@1.25GBd
Pavg, PRBS 231-1,
BER < 1*10-12@
10.3125GBd
OMA, PRBS 231-1, BER
< 1*10-12@2GBd
OMA, PRBS 231-1, BER
< 1*10-12@4GBd
OMA, PRBS 231-1, BER
< 1*10-12@8GBd
OMA, PRBS 231-1, BER
< 1*1012@10.3125GBd
Stressed Receiver
Sensitivity Ethernet
Stressed Receiver
Sensitivity Fiber
Channel (OM3
fibers)
Loss of Signal
-10.8
-9.0
-11.1
PIN
PIN
tbd
-7.5
-8.3
-17.5
Pav_as
POMA_deas
-12
Pav_deas
-17
Ethernet:1.25GBd *)
-30
Regulatory Compliance Module Safety
Approved Optics SFP+ modules are designed to meet international requirements and
standards in terms of product safety. Tests were performed according
to IEC 60950-1:2001 (CB scheme).The module is RoHS compliant according to the
European Parliament requirements on the restriction of the use of hazardous substances
in electrical and electronic equipment (RoHS). The modules optical output power
meet Class 1 requirements for laser safety.
Requirements
Module
Safety
RoHS
Compliance
Laser Eye
Safety
Standard
Status
IEC 60950-1:2001 EN 609501:2001
RoHS Directive 2002/95/EC
Amendment 4054 (2005/747/EC)
CDRH 21 CFR 1040.10 and
1040.11 IEC 60825-1 Rev2 2007
TUV Report / Certificate available CB
Report / Certificate available
RoHS 6/6 compliant Certificate of
compliance available
Laser Class 1 according to FDA
Laser Class 1 according to IEC Rev2
ESD & Electromagnetic compatibility
Approved Optics SFP+ modules are designed to withstand high ESD voltages. Its
excellent performances in terms of EMI allow system designers to integrate
the module in high density applications.
Approved Networks, Inc.
www.ApprovedOptics.com
Page 6 of 8
dBm
dBm
dBm
AA1403015-E6-A
SFP+, 10GBASE-SR 10G Ethernet Module
850mn, 300m, MMF, LC RoHS6
Requirements
Electro Static
Discharge to the
Electrical Pins (ESD)
Standard
EIA/JESD22-A114-B MILSTD 883C Method 3015.7
Immunity to ESD
(housing, receptacle)
IEN 61000-4-2
IEC61000-4-2
Electromagnetic
Emission (EMI)
Status
FCC Part 15, Class B EN
55022 Class B CISPR 22
Approved Networks, Inc.
Exceeds requirements Class 1B
(>1000V)
Exceeds requirements
Discharges ranging from 2kV to
25kV without damages to the
transceiver
Exceeds requirements Class B
with more than 6dB margin
www.ApprovedOptics.com
Page 7 of 8
AA1403015-E6-A
SFP+, 10GBASE-SR 10G Ethernet Module
850mn, 300m, MMF, LC RoHS6
Contact Information
Approved Networks is a leading supplier of Network Transceivers and
Connectivity products to Channel Partners, Resellers, and OEMs. With more than
9 years of direct industry experience, Approved Optics, Inc., our products are
resident in the most demanding and mission critical functional networks
Worldwide. We serve as a Master Distributor to the largest CM’s in the world and
deploy the most rigorous testing and firmware management programs to bring the
highest level of functional product to the market at a cost that makes sense.
Corporate offices: Approved Networks, Inc.
Tel:
800.590.9535
Web: www.ApprovedOptics.com
Approved
Networks, Inc.
www.ApprovedOptics.com
Page 8 of 8