Vehicle Security / Remote Start / Remote Access

2016 Super Duty
Vehicle Security/Remote Start/Remote Access
Vehicle Security / Remote Start / Remote Access
System Installation
CONTENTS
VEHICLE PREPARATION
Hood Switch Installation
*+,"",*-+
VSS Module Installation
Security Indicator LED Mounting
TPM Antenna Kit Installation
RMST Kit Antenna Installation
RMU Module Installation
GENERAL PROCEDURES
Learn VSS to vehicle
Shock Sensor Sensitivity Adjustment
Standard Remote Start Activation
RMU Remote Start Activation
RMU Activation
Contents
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
Vehicle Security/Remote Start/Remote Access
1
INSTALLATION
Vehicle Security / Remote Start / Remote Access - Super Duty
VSS System Components
Security Indicator LED (19D596) "Optional"
Super Duty
1.
Verify correct kit number.
Review VSS Kit Contents
NOTE:
Kits are vehicle specific and are not interchangeable.
2.
Review the VSS kit contents.
Vehicle Security System (VSS) Kit
Page 1 of 25
QUANTITY
DESCRIPTION
1
VSS Module
1
T-harness
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
2
Vehicle Security System (VSS) Kit(Continued)
6
Tie-straps
1
Owner's Manual
Security Indicator LED Kit Contents "Optional"
3.
Review the Security Indicator LED kit contents.
Security Indicator LED Kit
QUANTITY
DESCRIPTION
1
Security Indicator LED
I. VSS System Installation
CAUTION:
Carefully route and secure module and harnesses so that they do not interfere with moving parts
or linkages.
NOTE:
If the VSS kit was installed previously and the vehicle is being upgraded, proceed to the "RMST" or
"RMU" upgrade section(s).
4.
Remove the 2 bolts and remove the OBD II port from the IP frame.
5.
Connect the VSS T-harness to the OBD II port.
• Secure the T-harness to the OBD II port using a tie-strap.
Page 2 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
3
6.
Position the VSS harness inside the IP being careful to avoid sharp edges and moving parts.
7.
Install the new VSS harness OBD II port to the IP frame and install the bolts.
• Do not over tighten.
8.
Position the VSS module on top of the Body Control Module (BCM) and secure to wire harness
with tie-straps.
• Ensure the VSS module is positioned so the shock sensor adjustment knob can be accessed for
later use.
• Ensure the tie-strap is routed through the VSS module loops at opposite corners.
Page 3 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
9.
Vehicle Security/Remote Start/Remote Access
4
Connect the VSS harness to the VSS module.
• Secure the VSS harness with tie-straps.
Optional Security Indicator LED Mounting
CAUTION:
Carefully route and secure module and harnesses so that they do not interfere with moving parts
or linkages.
10. Keep the following points in mind when routing or positioning the LED for mounting:
• Have at least 3/4" clearance behind trim panels for the wiring harness to be routed.
• The LED should be clearly visible from the driver's side window when mounted.
• Do not mount the LED on trim panels that cover air bags.
11. Mount the LED at an appropriate location on the upper steering column shroud, using the guidelines
listed above.
• Drill a 9/32" hole into the selected location, for the LED to mount in.
12. Route the LED wire harness to the VSS module.
Page 4 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
5
13. Connect the LED wire harness to the VSS module 2-pin white connector.
• Secure the LED wire harness with tie-straps.
Learn VSS to Vehicle
NOTE:
Make sure the brake pedal is not depressed during this sequence.
14. Press the vehicle's unlock button located on the driver's door. Make sure all doors are unlocked.
15. Put the key in the ignition.
16. Cycle eight times rapidly (within 10 seconds) between the 1 (OFF/LOCK) position and 3 (ON)
position.
• The eighth turn must end in the 3 (ON) position. The doors will lock, then unlock, to confirm
that the programming mode has been activated.
17. Wait for 10 seconds and the remote start module will program itself to the system.
• After 20 seconds, you will automatically exit the programming mode. The doors will lock, then
unlock, to confirm that the programming mode has been exited.
18. If equipped with additional accessories (i.e. RF keypad), verify that they maintain all functionality
post installation.
Shock Sensor Sensitivity Adjustment
NOTE:
The VSS module is equipped with an internal dual zone Shock Sensor. The VSS system will activate a
single horn honk/single light flash anytime a light to moderate impact is detected, and a "panic" type 30
second horn honk/light flash sequence when a heavy impact is detected while the VSS system is armed.
Adjustment of both zones is accomplished through a single adjustment knob on the VSS module.
Rotating the knob clockwise will increase sensitivity and rotating the knob counter-clockwise will
decrease sensitivity. Sensitivity adjustment must be completed with the module securely mounted and
the adjustment knob accessible.
Page 5 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
6
19. Starting with the adjustment knob in approximately the halfway position, lower the driver's window
and exit the vehicle.
20. Press the LOCK button on the vehicle's RKE fob to arm the VSS system. The LED will light solid
for 20 seconds and then begin to flash a steady on/off sequence to indicate the system is armed.
21. Using a closed fist, impact the steering wheel with moderate force to simulate a light impact on the
vehicle. If the impact is detected, the horn will honk and the lights will flash 1 time to indicate the
warning impact was detected.
22. Using a closed fist, impact the steering wheel with heavy force to simulate a hard impact (i.e. glass
breakage) on the vehicle. If the impact is detected, the horn will honk and the lights will flash a
steady on off sequence to indicate the heavy or full shock trigger was detected.
23. Increase (rotate clockwise) or decrease (rotate counter-clockwise) the adjustment knob as necessary
to achieve desired sensitivity, repeat the previous steps to test, and verify adjustment.
VSS Functional Test
NOTE:
If installed, observe the LED while performing these tests.
24. Lower the driver's door window, then close all doors, hood, and trunk/hatch and press lock on the
keyfob. The LED should stay lit for 20 seconds while the VSS system pre-arms, after which it will
flash every 3-4 seconds in fully armed mode.
25. Reach inside the window hit the door unlock trim switch. The LED should continue to flash,
indicating that the vehicle is still armed. Use the inside driver's door handle to open the door. The
alarm should sound, indicating perimeter breach. Turn the alarm off by turning the ignition to "On".
• If equipped with OE perimeter security, there will be a 12 second interior chime prior to alarm
sounding. For vehicles not equipped with OE perimeter security, there will be a 12 second delay
with no interior chime prior to alarm sounding.
26. Exit the vehicle and arm it again, this time leaving the driver's door open. The vehicle should arm
itself, ignoring the open door but monitoring the rest. Once the vehicle is armed, shut the driver's
Page 6 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
7
door and reopen it after a few seconds. The alarm should sound. Turn the alarm off by hitting
unlock on the keyfob.
27. Test all other vehicle doors, the hood and the trunk in the same manner, by setting off the alarm and
disarming with the keyfob.
28. Please contact 1-800-FORD-KEY with any issues regarding hardware or kit contents.
II. Remote Start (RMST) Upgrade - Antenna Kit "Sold Separately"
CAUTION:
Carefully route and secure module and harnesses so that they do not interfere with moving parts
or linkages.
NOTE:
Verify that the vehicle has a hood switch Installed. If the vehicle is not equipped with a hood switch
refer to "Hood Switch Kit - Sold Separately".
Standard Key Fob (15K601) "Sold Separately"
Page 7 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
8
Bi-directional Key Fob (15K601) "Sold Separately"
Hood Switch Kit (19G366) - "Sold Separately"
Page 8 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
9
TPM Antenna Kit Components - "Sold Separately"
Optional RMST Upgrade Components "Sold Separately"
29. Review the RMST Upgrade components.
Remote Start (RMST) Upgrade - Antenna Kit "Sold Separately"
QUANTITY
DESCRIPTION
1
Bi-directional Antenna
1
Security Jumper
Standard Key Fob (15K601) "Sold Separately"
QUANTITY
DESCRIPTION
1
Standard Key Fob (15K601)
Bi-directional Key Fob (15K601) "Sold Separately"
QUANTITY
DESCRIPTION
1
Bi-directional Key Fob (15K601)
Hood Switch Kit Contents (if required) "Sold Separately"
30. Review the Hood Switch kit contents.
Hood Switch Kit "Sold Separately"
Page 9 of 25
QUANTITY
DESCRIPTION
1
Bolt
1
Hood Switch Assembly
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
10
TPM Antenna Kit Components "Sold Separately"
31. Review the TPM antenna kit contents.
TPM Antenna Kit
QUANTITY
DESCRIPTION
1
Antenna Module
1
Antenna Jumper Wire
1
2-sided Tape (not shown)
Hood Switch Kit - (if required) "Sold Separately"
NOTE:
Hood switch installation is optional for VSS installation and required if the vehicle is being upgraded to
RMST/RMU and is not currently equipped with a hood switch.
32. Locate the hood switch harness located on the LH side of the upper radiator core support.
Page 10 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
11
33. Install the Hood switch assembly to the existing hood switch mounting on the upper radiator core
support as shown.
• Install the bolt.
• Tighten to 10 Nm (89 lb-in).
34. Connect the electrical connector to the hood switch.
35. Install the hood switch wire harness push pin retainer to the hood switch bracket.
TPM Antenna Kit Installation
NOTE:
The TPM Antenna Kit is only required if the vehicle is not equipped with factory remote start.
36. Pull the rear edge of the overhead console downward, at the locations shown, and then pull
rearward.
Page 11 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
12
37. Disconnect the electrical connectors.
38. Remove the overhead console.
39. Remove the LH sun visor screws and the sun visor.
• If equipped, disconnect the electrical connector.
40. Remove the LH sun visor retaining clip screw and retaining clip.
41. Open the LH A-pillar trim panel bolt covers.
42. Loosen the LH A-pillar trim panel bolts.
Page 12 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
13
43. NOTE:
Carefully rotate the A-pillar trim panel during this step.
Remove the LH A-pillar trim panel.
44. Position the LH side of the headliner down far enough to access the Tire Pressure Monitor (TPM)
module.
• Connect the antenna jumper wire to the TPM module.
45. Secure the antenna module to the top side of the headliner using double-sided tape.
46. Connect the antenna jumper wire connector to the antenna module.
47. Install the LH A-pillar trim panel.
48. Tighten the LH A-pillar trim panel bolts.
• Tighten bolts to 8 Nm (71 lb-in) and close the bolt covers.
49. Install the LH sun visor retaining clip and retaining clip screw.
Page 13 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
14
50. Install the LH sun visor and sun visor screws.
• If equipped, connect the electrical connector.
51. Connect the overhead console electrical connectors and install the overhead console.
RMST Kit Antenna Installation
52. Remove the LH IP side finish panel.
53. Clean the antenna mounting surface using an alcohol base solution and a clean cloth.
54. NOTE:
Do not touch the adhesive, reduced adhesion may result.
NOTE:
Make sure that the long wire on the antenna is pointing towards the top of the windshield since this
wire will be routed along the headliner.
NOTE:
The wire will be attached to the control module later in this procedure.
Remove the protective backing from the adhesive on the antenna and firmly press the body of the
antenna onto the mounting surface.
55. If necessary, position the A-pillar trim slightly outward to provide access to route the antenna wire.
For additional information, refer to Workshop Manual (WSM) Section 501-05.
Page 14 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
15
NOTE:
Do not route the antenna wire over the top of air bags.
56. Route the antenna cable along the headliner and down the A-pillar towards the floor. Continue
routing the wire into the IP towards the VSS module.
• Secure with tie-straps.
57. Connect the antenna connector to the VSS module.
58. Reposition the A-pillar trim panel back, if necessary. For additional information, refer to WSM
Section 501-05.
59. If the RMST kit will not be upgraded to RMU functions at this time, install the LH IP side finish
panel.
VSS Module - Optional Vehicle Security Features
60. Enable/Disable Vehicle Security Features:
Locate the security jumper supplied in the kit.
• Install the jumper to the VSS module if the vehicle security features are to be disabled.
• Not installing and/or removing the jumper from the VSS module will keep the vehicle security
features enabled.
Page 15 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
16
RMST Activation
61. Verify that the IDS is updated to the most current version.
62. Connect IDS.
• Follow the prompts to select new vehicle session.
• Enter VIN.
63. Activate the remote start using the IDS.
• Select the Tool Box icon.
• Select Body.
• Select Security.
• Select Remote Start.
• Verify that the information on the IDS screen is correct and all procedures have been followed.
• Select Yes. This will enable the remote start function on the vehicle.
64. For vehicles equipped with standard message center, verify that the remote start option now
appears.
• Using the Select and Arrow buttons on the steering wheel, select Settings.
• Select Convenience.
• Select Remote Start.
• Select System.
• Verify that the remote start system is checked.
65. For vehicles equipped with advanced message center, verify that the remote start option now
appears.
• Using the Select and Arrow buttons on the steering wheel, select Settings.
• Select Vehicle Settings.
• Select Vehicle.
• Select Remote Start System.
• Verify that the remote start system is enabled.
Learn Remote Start to Vehicle
NOTE:
Make sure the brake pedal is not depressed during this sequence.
66. Press the vehicle's unlock button located on the driver's door. Make sure all doors are unlocked.
67. Put the key in the ignition.
68. Cycle eight times rapidly (within 10 seconds) between the 1 (OFF/LOCK) position and 3 (ON)
position.
• The eighth turn must end in the 3 (ON) position. The doors will lock, then unlock, to confirm
that the programming mode has been activated.
Page 16 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
17
69. Wait for 10 seconds and the remote start module will program itself to the system.
• After 20 seconds, you will automatically exit the programming mode. The doors will lock, then
unlock, to confirm that the programming mode has been exited.
70. If equipped with additional accessories (i.e. RF keypad), verify that they maintain all functionality
post installation.
Programming Key Fobs
71. NOTE:
These steps must be performed with the VSS module security jumper removed if previously
installed. For additional information refer to "VSS Module - Optional Vehicle Security Features".
1 Start with doors unlocked
2 Driver's door open (remaining open throughout)
3 Verify that the gearshift lever is in the "PARK" position.
4 Depress and hold brake pedal.
5 Start with ignition key OFF.
6 Cycle ignition key to the ON then OFF position 5 times, then back to the ON position a 6th time.
▪ The horn will honk 3 times to indicate transmitter learn mode access.
7 Press the START button on each transmitter you wish to program. The horn will honk 1 time
each time the START button is pressed to indicated the transmitter has been learned.
8 Cycle ignition key to the OFF position to exit transmitter learn mode.
9 NOTE:
If the security jumper is installed the vehicle security features are disabled.
If previously removed, reinstall the VSS module security jumper. For additional information,
refer to "VSS Module - Optional Vehicle Security Features".
RMST Functional Test
NOTE:
Do not put a key in the ignition for the following steps.
72. Make sure the shift lever is in PARK and the ignition is in the OFF position. Remove all keys from
the vehicle.
Page 17 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
18
73. Close the hood.
74. Close all of the vehicle doors.
75. Start the vehicle by pressing the remote start button twice on the remote start key fob.
76. Confirm the remote start works with the vehicle in park and with the hood and doors closed.
77. Open the hood.
78. NOTE:
Vehicle doors should be closed while performing this step.
Confirm that the vehicle will not start with the hood open.
Please contact 1-800-FORD-KEY with any issues regarding hardware or kit contents.
79. See the Scalable Remote Start System Diagnosis Guide to resolve issues identified by the functional
test.
III. Remote Access (RMU) Upgrade "Sold Separately"
80. Review the RMU upgrade components.
Optional Components — Remote Access (RMU) Upgrade "Sold Separately"
QUANTITY
DESCRIPTION
1
Remote Messaging Unit (RMU)
1
SIM Card Carrier
1
Security Jumper
81. If previously installed, remove the LH IP side finish panel.
CAUTION:
Carefully route and secure module and harnesses so that they do not interfere with moving parts
or linkages.
NOTE:
For proper range of operation, the RMU must be installed as shown in the diagram below.
Page 18 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
19
82. Using a tie-strap secure the RMU to the A/C duct behind the LH IP side finish panel.
83. Connect the RMU electrical connector to the VSS module.
• Secure the harness with tie-straps.
VSS Module - Optional Vehicle Security Features
84. Enable/Disable Vehicle Security Features:
Locate the security jumper supplied in the kit.
• Install the jumper to the VSS module if the vehicle security features are to be disabled.
• Not installing and/or removing the jumper from the VSS module will keep the vehicle security
features enabled.
Page 19 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
20
85. Install the LH IP side finish panel.
Remote Start Activation - (Vehicles Without Factory Remote Start)
86. Verify that the IDS is updated to the most current version.
87. Connect IDS.
• Follow the prompts to select new vehicle session.
• Enter VIN.
88. Activate the remote start using the IDS.
• Select the Tool Box icon.
• Select Body.
• Select Security.
• Select Remote Start.
• Verify that the information on the IDS screen is correct and all procedures have been followed.
• Select Yes. This will enable the remote start function on the vehicle.
89. For vehicles equipped with standard message center, verify that the remote start option now
appears.
• Using the Select and Arrow buttons on the steering wheel, select Settings.
• Select Convenience.
• Select Remote Start.
• Select System.
• Verify that the remote start system is checked.
90. For vehicles equipped with advanced message center, verify that the remote start option now
appears.
• Using the Select and Arrow buttons on the steering wheel, select Settings.
• Select Vehicle Settings.
• Select Vehicle.
• Select Remote Start System.
• Verify that the remote start system is enabled.
Page 20 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
21
Learn Remote Start to Vehicle
NOTE:
Make sure the brake pedal is not depressed during this sequence.
91. Press the vehicle's unlock button located on the driver's door. Make sure all doors are unlocked.
92. Put the key in the ignition.
93. Cycle eight times rapidly (within 10 seconds) between the 1 (OFF/LOCK) position and 3 (ON)
position.
• The eighth turn must end in the 3 (ON) position. The doors will lock, then unlock, to confirm
that the programming mode has been activated.
94. Wait for 10 seconds and the remote start module will program itself to the system.
• After 20 seconds, you will automatically exit the programming mode. The doors will lock, then
unlock, to confirm that the programming mode has been exited.
95. If equipped with additional accessories (i.e. RF keypad), verify that they maintain all functionality
post installation.
RMU Activation
NOTE:
Please note that the Remote Access application that is used to start the vehicle for this RMST kit will
only work with iPhone and Android phones.
96. For RMU activation the following information from the customer is recommended to provide them
with electronic notification for app retrieval:
1 Email Address
2 Cell Phone Number
3 Cell Phone Carrier Company
97. Log on to your Professional Technician Society (PTS) account and enter the vehicle information.
1 Select "Vehicle Id".
2 Select "By Year & Model"
3 Choose the year & model of the vehicle and then select "GO".
4 Hover over the "Workshop" tab.
5 Select the "Accessory Installation" menu item.
6 Under the "Electrical" heading, select the "Remote Access Activation" link (first time users will
need to agree to terms & conditions).
7 Select the "Install or Diagnose" link.
Page 21 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
22
NOTE:
If you are not directed to the screen shown below (or user agreement screen for first time users), make
sure your internet browser zone settings are set to medium. This setting can be found in your browsers
"internet options" under the "privacy" tab.
98. Once on the "Install" page, enter the SIM ID code that was provided with the RMST kit. Select
"Begin or Continue Installation".
Page 22 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
23
99. Click on the "On screen steps 1-6", and follow the on screen instructions to complete the
installation.
Page 23 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
24
NOTE:
The following step will complete the activation process, when you are directed to a screen similar to the
one below ensure the correct vehicle brand is selected and that all applicable features are enabled.
NOTE:
The "perimeter" and "shock" settings below are optional features and should only be selected when
security features are enabled.
Page 24 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo
2016 Super Duty
INSTALLATION (Continued)
Vehicle Security/Remote Start/Remote Access
25
100.Perform a functional check of the system by testing each of the available features.
• Start/Stop function
• Lock/Unlock function
• Car finder
• Signal (for troubleshooting only)
NOTE:
All tests above must be completed in order to move to the next step. If any of the listed functions fail,
move the vehicle to an outside location and retest.
NOTE:
In the event start or stop fail, refer to the "Remote Start Activation" section in this manual.
NOTE:
In the event lock/unlock or car find fail, refer to the "Learn Remote Start System to Vehicle" section in
this manual.
101.Once the hardware installation and RMU activation process is complete, record the 4-digit PIN on
the SIM card carrier. Provide the SIM card carrier to the customer so they can add this system to
their Remote Access Account. Customer must have both the 4-digit PIN and SIM ID to activate/add
their vehicle to their Remote Access Account.
102.If the customer agrees, you may push the mobile application to the customer. You will need the
customer's phone number and cellular carrier. If the customer opts to install the application
themselves, they can locate it in their mobile app store.
Please contact 1-800-FORD-KEY with any issues regarding hardware or kit contents.
Page 25 of 25
SK9L2J-19G364-AA
© Copyright Ford 2015 FoMoCo