English
User Manual
F3760 TV Mount
FIXED FLAT PANEL TV MOUNT
37” - 70”
94cm - 178cm
150 lb
(68 kg)
50x50
600x400
VESA
Supporting your digital lifestyle™
Table of Contents
Table of Contents / Introduction . . . . . . . . . . . . .
Supplied Parts & Hardware . . . . . . . . . . . . . . . . . .
Setup - Step 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup - Step 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup - Steps 3 to 4 . . . . . . . . . . . . . . . . . . . . . . . .
Other Kanto Products . . . . . . . . . . . . . . . . . . . . . .
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3
4
5
6
7
8
Introduction
Thank you for choosing a Kanto wall mount. The F3760 is designed to mount flat panel televisions weighing up to 150 lbs
(68 kg) within 1” of your wall.
Read these instructions fully before installation of this mount. If you do not understand these directions, or have any
doubts about the safety of the installation, please consult a qualified installation contractor to install this mount. Make sure
there are no defective or missing parts. Do not use defective parts. If you are uncertain whether the part is defective call
Kanto directly at 1-888-848-2643 or email support@kantoliving.com. Kanto cannot be liable for property damage or injury
caused by incorrect mounting, incorrect assembly, lifting or incorrect use of this product.
This product should not be mounted on steel stud walls or cinder block walls. Consult a qualified installation contractor if
you are unsure about the type of wall you may have. We make every effort to ensure all necessary hardware is included. If
there is hardware missing please call Kanto directly at 1-888-848-2643 or email support@kantoliving.com.
See installation video online at:
www.kantoliving.com
CAUTION
The maximum loading weight is 150 lbs (68 kg). This wall mount is intended for use only within the maximum
weight restrictions indicated. Use with products heavier than the maximum weights indicated may result in instability
causing possible injury.
CAUTION
The wall you plan to affix the Kanto mount to must be able to support more than 5 times the weight of the
television and the wall mount combined. Do not use this product for any purpose other than to mount a flat panel
TV on a vertical surface as outlined in this manual. Improper installation may cause damage to your TV or serious
injury. This product should not be mounted to steel stud walls, cinder block or old concrete walls. Consult a qualified
installation contractor if you are unsure about the type of wall you may have.
2
Supplied Parts and Hardware
Wall Plate
x4
A: M5 x 15mm
Bolt
x4
x4
B: M5 x 25mm
Bolt
C: M6 x 15mm
Bolt
x4
x4
x4
x4
D: M6 x 25mm
Bolt
E: M8 x 15mm
Bolt
F: M8 x 25mm
Bolt
G: M8 x 35mm
Bolt
x4
x4
H: Washer
I: Lag Bolt Washer
x4
x4
J: Plastic Spacer
x4
K: Lag Bolt
x2
R: Quick-Lock
TV Bracket
L: Concrete Anchor
Required Tools
Socket
set
Phillips
Screwdriver
Hammer (for
concrete
installs)
Supporting your digital lifestyle™
Pencil
Stud
Finder
Level
Drill
7/16”
Masonry
Bit
3/16”
Wood
Bit
3
Step 1: Attach TV Brackets
There are a wide variety of TVs available that require different bolt sizes. We provide a selection of mounting bolts to
fit most TVs. If you have any concerns about this mounting hardware or installation call us direct at 1-888-848-2643 or
email at support@kantoliving.com.
Step 1.1 Select the correct size of bolt.
Kanto provides 3 bolt diameters (Metric sizes M5, M6 and
M8) in various lengths.
Part items: A, B, C, D, E, F or G.
Select the correct diameter bolt and hand thread into the
back of the TV to determine the correct length. Use the
longest available bolt without reaching the bottom of the
TV threads.
Use the washer (H) for bolts A to D (sizes M5 and M6).
The washer will work for both bolt sizes. The washer is
not required for M8 size bolts (E, F & G).
If your TV has a curved back or deep recesses, you can
use the spacers (J).
Step 1.2 Attach TV bracket arms to the back of the TV
Attach the arms to the TV, as shown in Diagram A.
Quick-Lock TV bracket (R)
Spacer (J), if necessary,
depending on length of bolt
and depth of recess
Washer (H) used
with screws A thru D
Bolt (Choose A thru G)
Diagram A
WARNING
Never over-tighten a bolt into the back of your flat panel TV.
Do not lay the TV face down on its glass front. Use a wall or a TV stand.
4
Step 2: Mount Wall Plate
Wood Stud Wall
The Wall Plate must be mounted to two wood studs. Use a stud sensor to locate the two studs, clearly marking the outer
edges of the studs (see Diagram B). Use a long level to ensure the two holes are level at the desired height.
Pre-drill two upper holes in the center of your studs, and attach the Wall Plate to the wall using 2 Lag Bolts (K) and Lag
Bolt Washers (I) (see Diagram B). Do not over-tighten lag bolts (K). Make sure the Wall Plate is flat against the wall surface.
Using the Wall Plate as template, pre-drill the bottom 2 holes, and secure using 2 Lag Bolts (K) and 2 Lag Bolt Washers (I),
taking care not to over-tighten.
3” (75mm)
CAUTION
Make sure the supporting
surface will support the load limits
outlined in the Caution at bottom of
page two. Tighten Lag Bolts until the
Wall Plate is snug flat against the wall.
Do not over tighten Lag Bolts (K). Each
Lag Bolt must be located in the center
of a wood stud.
3/16
(5mm)
I
K
Diagram B
Brick or Concrete Wall
Using the Wall Plate as a template, mark four holes toward the outer edge of the Wall Plate at your desired height (see
Diagram C). Adjust the Wall Plate position to be clear of mortar joints, keeping in mind that the mount provides minor
horizontal shift along the length of the Wall Plate. Use a long level to ensure the four holes are level and at the desired
height.
Pre-drill four holes, and insert a Concrete Anchor (L) into each of the holes flush with the concrete wall surface and not
flush with the surface covering, such as drywall.
Attach the Wall Plate using 4 Lag Bolts (K) and Lag Bolt Washers (I) (see Diagram C). Make sure the Wall Plate is flat against
the wall surface. Do not over-tighten Lag Bolts (K).
L
3” (75mm)
L
7/16
(11mm)
CAUTION
Make sure the concrete or brick wall
is at least 3.5” thick. Make sure the anchor
is seated completely flush with the concrete
surface even if there is another layer of
material, such as drywall. If drywall is over
5/8” thick custom lag bolts must be used.
Concrete must be a minimum of 2000psi in
density.
Supporting your digital lifestyle™
K
I
Diagram C
5
CAUTION
Read this section carefully prior to install.
WARNING
Use two people to lift and position the TV onto the Wall Plate.
Step 3: Attach TV to Wall Plate
With the TV brackets firmly secured to the TV, use two people to lift the TV into position and hook the TV brackets onto
the wall plate, as shown in Diagram D.
The two spring loaded Quick-Lock brackets will snap into place as you lower the bottom of the TV onto the plate.
For minor level adjustment, you can adjust the two top screws using a Phillips screwdriver to ensure the TV hangs level,
as shown in Diagram E. If you need to release pressure on the screws, pull down slightly on the Quick Release cords as
shown in Diagram F.
Loosen
Hook
Level
Pull
Cord to
Release
Diagram D
Diagram E
Diagram F
Step 4: Release the TV
Because the TV sits so close to your wall, the Quick-Lock TV brackets are equipped with quick release cords. Loosen the top levelling screws slightly to release tension, then simply pull to release both Quick-Locks (as shown in Diagram F), and pull the bottom of
the TV away from the wall. Then, using two people, lift the TV up and away from the wall plate.
6
Check out more great products from Kanto!
Kanto Speakers
• Check out our full line of bookshelf and desktop speaker systems
• Available in a stunning array of colors
• Visit kantospeakers.com for more!
+
SP26
+
by
• Full line of Audio and Video Cables
• White or Black Cables available
• HDMI, Optical, Mini-jack, RCA, USB
• Switchers, Hubs, and Adapters
• Visit kantoliving.com
To learn more about all our products, visit www.kantoliving.com
Kanto Living
Supporting your digital lifestyle™
@kantoliving
kantoliving
7
Warranty
Limited Warranty to Original Purchaser
Kanto Distribution Inc. (Kanto) warrants the equipment it manufactures to be free from defects in material
and workmanship for the following limited warranty period of: 5 years parts and labour
If equipment fails because of such defects and Kanto or an authorized dealer is notified within 5 years
from the date of shipment with proof of original invoice, Kanto will, at its option, repair or replace the
equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse
or modifications. Equipment that fails under conditions other than those covered will be repaired at the
current price of parts and labor in effect at the repair. Such repairs are warranted for 90 days from the day
of reshipment to the original purchaser. This warranty is in lieu of all other warranties expressed or implied,
including without limitation, any implied warranty or merchantability or fitness for any particular purpose,
all of which are expressly disclaimed. Customers will be responsible for obtaining a Return Authorization as
well as shipping costs to return product to a Kanto location or authorized depot listed on the website. If the
equipment is covered under the warranty provisions above, Kanto will repair or replace, and be responsible
for return shipping to the customer. Please keep the original packaging so products will not be damaged
during shipping, and we recommend you insure your shipment. If equipment fails outside the warranty
provisions, customers will be quoted repair and return shipping costs prior to work being performed.
The information in the owner’s manual has been carefully checked and is believed to be accurate. However,
Kanto assumes no responsibility for any inaccuracies that may be contained in the manual. In no event will
Kanto, be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect
or omission in this manual, even if advised of the possibility of such damages.
16-E
www.kantoliving.com
support@kantoliving.com
Tel 888.848.2643