English 433CCD无线条码阅读器(V1.0) .cdr

Catalogue
Product Characteristic and Function and Use Description
Pairing Operation
Working Mode and Language Setting ......... ..........
Continuous Scanning Mode
....
Barcode Type
Settings
Barcode Character Transfer Delaying Settings
Parameter Barcode
Parameter Barcode and Corresponding Representing Characters Table
Charging . . . . . . . . . . .
Warranty . . . . . . .
Maintenance Card and Configuration List
1
15
17
20
22
Respected clients:
Thanks for choosing us. We hope you take your valuable time to read the user
manual before using the barcode reader. Hope this will be a good base for a
smooth use. Any enquiries, please contact us.Thanks.
I.Pro duct Characteristic:
a. Exquisite and beautiful design, external protected by soft rubber and internal
scientific solidification structure, so its drop resistance better than ordinary scanner.
b.The latest technical accomplishment is applied to the engine and decoding
function, reading codes better and faster than the similar in the market.
c.Easy using, easy setting.
d.Large capacity, 1.5 times higher than ordinary scanner, it guarantees use
longer after fully charged.
II Function and Use Description
a.Automatic frequency hopping and strong anti-interference capacity
b. Under the “Normal Mode”, the transmission distance is over 400m where
there are no obstacles. If exceed the transmission distance or the data is
loaded failed, 3 short prompt sound will be sent out.
c.Each scanner has a unique mechanical ID, it guarantees not disturb each
other when many scanners work at the same time.
d.The customizable ID enables the user to distinguish the data source easily.
e.The pairing method is very simple, one pairing can be used for a long time
and repeated pairing is applicable.
f.The “Check Mode”is simple and can be used easily, and can storage 500-10000
barcode messages(customization is needed if messages are more than 500).
g.Automatic sleeping, the sleeping current is less than 10UA,which largely
prolongs the standby time of battery.
h.A special charging circuit guarantees the charging safety.
III.Pairing Operation
( I ) Pairing Mode
One to One
Pairing operation: first insert the receiver into the computer usb interface and the receiver indicator light
will be on (default is 5s).Need to read “One to One” barcode in 5s, the scanner will have two “beeps” and
the light will be off and shortly to flickering mode. This shows the scanner can communicate. If not succeed
there will be three "beeps", should pair again. The "One to One" mode can support 1 million scanners
working at the same location.
(II)ID Display and Hiding Setting
Opening ID Setting
ID Display
*ID Setting Parameters
4
Hiding
(III) Sleeping Time Setting
Opening Time Setting
2 min
8 hour
s
s
10 min
5 min
No Sleeping
5
60s
20 min
( IV) Working Mode Setting
Normal Mode
Non-Losing Mode
Upload Checking Data
Clear Checking Data
Check Mode
Restore Checking Data
Total Checking Data
Clear Non- Losing Mode
Stored Data
Explanation: Under “Non-Losing Mode”, when exceeding the wireless transmission range, the data will be
stored and after reaching the wireless transmission range the data will be uploaded to the receiver. If no need
the stored data, please read “Clear Non-Losing Mode Stored Data”barcode setting to clear data.
* Language Setting
English
Italian
German
French
Turkish
Czech
Finnish
Spanish
6
IV.Restore Setting
Enter into Settings
Restore Factory Settings
Exit Settings
V.Flicker Scanning Mode
Flicker Scanning
Flicker Scanning Time
Attention:The fl icker sca nni ng time can be set through reading the “ Par ameter Bar code” 01-09. Flicker
time interval unit as 500 ms and can set 01-15 grade. For example, if the flicker time inter val is 1000 ms,
the procedures are “Enter Into Settings”- “Flicker Scanning Time”- “Parameter Barcode “0” “2” - “Quit
Settings”.
VI.Auto Scanning Mode
Auto Scanning
Reading Barcode Time
7
Exit Settings
Enter into Settings
Attention: Press the switch button after Auto Scanning Mode setting is accomplished,the scanner will automatically read
the following barcodes. If re-press the switch button, the scanner will stop reading barcodes. Under default mode, it is
not allowed to read the same barcode. Under the auto scanning mode, the reading barcode time can be set and time
unit as 1s, the parameters range is 0-15s, 0 is infinite and can set if allowed to repeat reading the same barcode.
Not Allowed to Repeat
Scanning the Same Barcode
Allowed to Repeat
Scanning the Same Barcode
Start Timing after
Scanning the Barcode
Attention: 1. Allowed to Repeat Scanning the Same Barcode Setting
When allowed, the scanner will automatically read the following barcodes.If re-press the switch button,the
scanner will stop reading barcodes.
When not allowed, the scanner will automatically read the following barcodes. If the same barcode comes
again, a continuous waiting mode will show.If there is no same barcode, the scanner keeps reading till you
re-press the switch button, the scanner stops reading.
2: Start Timing after Scanning the Barcode Setting
After a successful reading, reading time returns to zero and start timing.
VII Continuous Scanning Mode
Continuous Scanning
Scanning Interval Time
Scanning the Same
Barcode Interval time
Attention:When Continuous Scanning Mode set, the scanner enters into continuous reading code without pressing
switch button. Under continuous scanning mode, the scanner can set the scanning interval time and the interval time
unit as 500ms, parameter range is 0-7500ms. Under continuous scanning mode allows continuously read the same
barcode via setting scanning interval time.
Read the same barcode twice in 0.1 seconds, the time interval can be set between 0 and 12.0 seconds. When set
to 12.7 seconds means not allow to read the same barcode. The numerical must have three numbers, zero shows if
less than three numbers.
For example: the scanning interval for the same barcode for 2000 ms steps as follows:
1. “Enter Into Settings” 2. 〝 Scanning the Same Barcode Interval Time〞 3. 〝Parameter Barcode 〝 0〞〝 2〞〝0”
4. 〝 Quit Settings〞
VIII Security Level Settings(Attention:
The higher the level, the lower the reading barcode error
rate and slower the speed)
Enter into Settings
1
Exit Settings
3
2
4
IX Barcode type settings
Open The Code
ID Before Barcode
Close The Code
ID Before Barcode
Restore Default the Code ID
Attention: The code ID before the barcode means the corresponding barcode type, please check the sheet1-1.
Barcode Type
UPC-A
UPC-E
EAN-8
EAN-13
ISSN
ISBN
Code 128
GS1-128
ISBT 128
Code 39
Code 93
Code 11
Interleaved 2 of 5
Enter into Settings
CODE ID
Code Type
A
ITF-6
ITF-14
Matrix 2 of 5(Europe)
Matrix 2 of 5(Japan)
Industrial 25
Standard 25
Codebar
Plessey
MSI-Plessey
B
C
D
E
F
G
H
J
Gs1 Databar
K
L
M
N
Sheet 1-1
CODE ID
O
P
S
T
U
V
W
X
Y
Z
Exit Settings
X Barcode Character Transfer Delaying Settings
Character Delaying Time
Attention: character delaying time is 0-75ms, 5ms as a grade,
15 grades in total. The default is 0ms.
10
Exit Settings
Enter into Settings
XI Barcode Enable
Attention: if some barcodes can't be read, please
read “Read All Types of Barcode”and restore the
factory default in case affecting the scanning speed.
Read All Types of Barcode Forbid to Read All
Types of Barcode
XII UPC/ EAN-Attached Code Settings
Add Two Bits Attaced Code
*Code39 to or not to transmit start character
and stop character
to Transmit
Add Five Bits
Attached Code
XIII Enter and Line Skip Settings
Cancel Enter
Enter
11
Not to Transmit
XIV Parameter Code
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Save
Attention:If error happens after reading the
parameter, please read "reset parameter"
code to reset the needed parameter.
Reset Parameter
12
Enter into Settings
Exit Settings
XV Add Prefix Setting
Add Prefix
Reveal Prefix
Not Reveal Prefix
For example: if need to add suffix "XY"before code“1234”steps as follows: 1.Enter into Settings 2.Add Prefix
3.read parameter code 5,8,5,9 and then read "Save”4.Quit Settings. After above settings and read Reveal”Prefix”
code, when read code”1234”again the “XY” will be change to: XY1234.
XVI Add Suffix Settings
Add Suffix
Reveal Suffix
Not Reveal Suffix
For example: if need to add suffix “XY”after code“1234”, steps as follows:
1.Enter into Settings 2.Add Suffix 3.read parameter code 5,8,5,9 and then read “Save”4.Quit Settings.
After above settings and read “Reveal Suffix”code, when read code“1234”again the“XY”will be
added,change to:1234XY.
13
XVII Add the Function Key Terminator
Exit Settings
Enter into Settings
Terminator
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
HOME
TAB
14
XVIII ASCII Code Setting(Attention:
This setting aims to code 39 reading incompleted characters)
Open
Close
XIX Parameter barcode and corresponding representing characters table.
Parameter code Representing characters Parameter code
Representing characters
Parameter code
Representing characters
Parameter code
Representing characters
Parameter code Representing characters
2
2
2
2
2
2
2
2
2
2
2
2
15
1
2
3
4
5
6
7
8
9
a
b
c
Simple Operation Guide
I.Pairing operation: first insert the receiver into the computer usb interface and the receiver
indicator light will be on ( default is 5s) . Need to read “One to One”barcode in 5s , the
scanner will have two “beeps” and the light will be off and shortly to flickering mode . This
shows the scanner can communicate.
Attention: Pairing operation needs to accomplish in 5 seconds and can not set after blue
indicator light is flicking. Needs to pull off usb receiver and insert receiver into the usb
nterface and re-set as the previous steps. If not succeed there will be three “beeps”, if
succeed there will be two “b e e ps”.
II .ID Setting
After pairing operation is set, scanning“Opening ID Setting”, then scanning number you
need(Read“0” and “1”represent the ID is 1) .
III.Switching off
When the scanner arrives at the previous set sleeping time, it is switched off automatically
(the default setting is 20s ). Meantime it can be switched off compulsively by pressing the
on/off button for 2 seconds.if the sleeping time is too short,can self-customize sleeping
time(e.g.2minutes).
16
IV.Charging
Please use our equipped charging cable to charge the scanner. If indication light is red,
battery is being charged. When the battery is charged fully, the indication light will turn
to blue.
Note: Under the “Non-Losing Mode”, when the signal exceeds the transmission distance and
the receiver terminal can not receive signals. Barcode data which are read will be stored
automatically, which guarantees the barcode data will not be lost.
The lost barcode data which are stored will be loaded in the computer automatically as
long as the scanner can receive signals. Under this mode, working will not affected by the
transmission distance and the work efficiency of the user can be greatly improved!
17
Sound Promotion Guide
1.Scanning setting alarm: One short beep.
2.Pairing operation failure: Three short beeps.
3.Data Unloading Success: two short beeps, Failure: three short beeps.
4.Low voltage alarm: A long beep happens when the scanner is on or scanning .
Performance Parameters
Light Source: 620nmVisible red light diode
Trigger Mode: Manual (can be switched
” off after the on/off button is pressed
for several seconds).
Imaging Sensor: CCD
Scanning Speed: 280times/second
Reading Precision: ≥ 5mil
Charging input voltage: 5VDC±0.25V
Max. Power: 650mw
18
Current:Max.Current 130ma, Working Current 86ma, Standby Current 42ma,
Sleeping Current 5ua
Scanning angle:55° 25° 75°(Tilt, Rotate, Deflection)
Decoding capacity: Code128, EAN-13, EAN-8,Code39,UPC-A, UPC-E,Codabar,
Interleaved 2 of 5,ISBN, Code 93, UCC/EAN-128, GS1 Databar, etc.
Promotion pattern: Buzzer and LED indicator
Weight: 200g
Gun Size: Length*Width*Height:158mm*68mm*96mm
Charging interface type: RJ-45 crystal head, one meter long (equipped with 5V
charger; the battery is being charged when the red light is on and fully charged
when the blue light is on)
Hull material: ABS+PC
Temperature: 0︒C to 50︒C(Work)-40︒C to60︒C (Storage)
Setting mode: Manual (scanning and setting barcodes according to the sequence)
Electrical Safety: EN60950-1
EMC: EN55022, EN55024
Packaging level: IP 52
Anti-seismic capacity: This product can still work properly after falling down and
being impacted on the concrete floor from 3 meter.
19
About the Warranty
I.Since you buy our product with this card, you can enjoy the service of one year repair and lifelong maintenance for
the rubber and plastic parts of the barcode scanner,6 months repair service for the battery and the charger, and 3
months repair service for the data cable. During the repair period, the maintenance of the product is free.
Expire the warranty, we will charge the replaced components and maintenance cost;
II.If the product belongs to one of the below situations and verified by manufacturer, the user can't
enjoy the free maintenance service:
a. Expire the warranty period;
b. The barcode scanner body is disassembled or the camera of the scanner is damaged;
c. The surface or internal component of the scanner is seriously damaged;
d. The product is damaged due to the wrong installation or operation;
e. The serial number of the scanner is altered or does not confirm to the number written on the card.
f. The scanner is damaged due to an artificial fault. For instance, it is inundate.
g. The scanner is damaged due to natural disasters, e.g. fire disaster, flood and thunder stroke.
h. The working or storage environment of the product, e.g. temperature or humidity, does not
conform to the requirements in Operation Manual.
Thank You For Choosing Our Products!
20
Name
Name
Distributor Information
User Information
Address
Zipcode
Tel
Email
21
Address
Zipcode
Operator
Signature
Distributor
Seal
Barcode Reader
Maintenance Recode
Warranty Card
Date
Part No.
Fault
Description
Maintenance Operator
Record
Serial No.
Purchase Date
Appendix
Accessories Name
Scanner
U Type Receiver
Quantity
USB Charge Cable
Manual
Please make sure to read the instructions about maintenance
carefully at the back of the card. Fill out various data above
carefully and the file vaild only if it is signed with the offical
of the authorized dealer.
22