Wireless Keypad 3528135717 - Genie Garage Door Openers

FEATURES :
3528135717
• Ability to Control up to three
OF U.S. & IMPORTED PARTS
•
Genie® INTELLICODE® Openers
Simple to Program and Install
PIN Codes can be up to 8 Characters
Low Battery Power Indicator
Stays Programmed During
Battery Change
Temporary PIN for Special Purpose Access
TOOLS NEEDED:
This Wireless Keypad is compatible with all INTELLICODE® radio equipped GENIE® products.
•
•
•
•
Red LED
indicates
Battery Power
and Status
during Use
and Programming
Drill with 1/16" Drill Bit
Phillips Screwdriver
Pencil
Mounting Screws INCLUDED inside
Battery Compartment
OPERATING INSTRUCTIONS (KEEP FOR FUTURE REFERENCE)
WARNING
SECTION PROGRAMMING FOR
2 2 OR 3 DOOR OPENERS
3
Program Keypad BEFORE mounting.
Program Keypad BEFORE mounting.
STEP 1: SETTING YOUR WIRELESS KEYPAD PIN
STEP 1: SETTING YOUR WIRELESS KEYPAD PIN
A
A
(PERSONAL IDENTIFICATION NUMBER)
Activate programming mode.
• Press (in order)
.
– Red LED blinks - once per second.
• Enter your PIN (3 to 8 characters).
• Enter your PIN (3 to 8 characters).
• Press
• Press
.
STEP 2:
PROGRAMMING ONE DOOR OPENER
Find the Learn Code Button and Learn Code
Indicator LED on your door opener.
– If your Door Opener has a
black Antenna Wire,
Red Indicator
the Learn Code Button
LED
and Indicator LED
are located near the Antenna.
(The Light Lens may need
to be opened.)
– If your Door Opener does not
have an Antenna,
you have an External Receiver.
The External Receiver cover
must be removed to access
the Learn Code Button
and Indicator LED.
.
– Red LED blinks - twice per second and turns off.
– Red LED blinks - twice per second and turns off.
A
Activate programming mode.
• Press (in order)
– Red LED blinks - once per second.
STEP 2: PROGRAMMING THE KEYPAD FOR
MULTIPLE DOOR OPENERS
A
• Enter your PIN and press
4
again.
– Red LED blinks - twice per second.
A
• Press the number of Doors (total) you wish
to control (
• Press
Learn
Code
Button
on Keypad.
– Learn Code Indicator LED stays on.
or
STEP 3:
A
PROGRAMMING DOOR OPENERS
ADDITIONAL OPERATIONS
Erase old PIN.
Programming Door Opener(s).
USING A TEMPORARY PIN
A temporary PIN allows temporary access to your home by
repair persons, meter readers, etc.if you so desire.
Decide which Door will be Door #1,#2 and #3.
• Enter your PIN and press
again.
A
B
Door Opener (
• Press
• Enter your PIN.
or
B
• If the Door does not move,check the red LED on
• DO NOT reprogram the Door Opener(s).
• Temporary PIN remains active until the next time your
normal PIN is entered.
.
CHANGING BATTERY
PROG
If the red LED does
Figure 2
not blink during use,
the battery needs to Red LED
be changed.
Repeat step A above for each Door Opener.
Each Door Opener must be programmed to receive the
signal from the Wireless Keypad.
Wait until Keypad Backlight turns off (approximately 30 seconds).
STEP 4: OPERATING 2 OR 3 DOOR OPENERS
A
• Enter your PIN.
• Press
2
JKL
MNO
PQRS
TUV
WXYZ
4
7
0
5
8
3
6
9
Bottom
Mounting
Screw
Press here
FCC and IC CERTIFIED
.
• Press Door Opener number (
DEF
1
GHI
Battery
Covers available in:
• Brown - P/N 35365R
• Almond - P/N 35365S
• Sandstone - P/N 35365T
To move one of the Doors.
or
or
For answers to questions, call 1-800-35 GENIE, or visit
www.geniecompany.com
Additional Genie® products can be ordered using the Accessories
page in your Owner’s Manual or through the 800 number above.
.
NOTE
).
– Learn Code Indicator LED turns off.
.
Proceed to Section 3 - Mounting Instructions.
• Press
– Learn Code Indicator LED stays on.
To move the Garage Door.
Keypad. If the LED is blinking rapidly,the PIN was
entered incorrectly. After the LED stops blinking,
re-enter your PIN and try again.
• Any Keypad Button will control the Door for 30 seconds
after the Door starts moving.
• Rapid blinking of the red LED indicates an error. After a
few seconds the LED will turn off. Start over.
or
.
Enter the Temporary PIN (from 3 to 8 characters).
• Press the number you have picked for this
OPERATING ONE DOOR OPENER
NOTE
Enter your PIN.
• Press
on Keypad.
– Learn Code Indicator LED stays on.
©2005 The Genie Company, D.B.A. GMI Holdings, Inc.
MOUNTING INSTRUCTIONS
• Release all buttons.
– Learn Code Indicator LED (on Opener) blinks.
Wait until Keypad Backlight turns off (approximately 30 seconds).
• Press
9V
– Red LED will blink once and turn off.
.
• Press the Learn Code Button (see Section 1 Step 2).
– Door moves.
A
9
.
B
– Learn Code Indicator LED turns off.
STEP 3:
8
0
).
– Red LED blinks several times and turns off.
again.
• Press
7
3
6
• Return to“Programming” (Section 1 or Section 2).
– Learn Code Indicator LED (on Opener) will blink.
• Press
WXYZ
• Press and hold in order -
• Press the Learn Code Button.
• Enter your PIN and press
TUV
FORGOT YOUR PIN
OR
CHANGING YOUR PIN
.
– Red LED blinks - once per second.
Located
on Opener
Housing
PQRS
SECTION
All Door Openers will use the same PIN.
• Press
MNO
5
The Keypad must be mounted in sight of the Door(s), at
least 5 feet above the ground and clear of any moving
Door parts.
A Mount Keypad.(Mounting screws located inside
Battery Compartment.)
• Remove Battery Cover (See Section 4 Figure 2).
• Drill a 1/16”pilot hole for the top mounting screw.
• Install a screw into the drilled
Figure 1
hole,leaving a 1/8" gap
between the screw head
1"
and the wall. See Figure 1.
8
Wall
• Hook the Keypad over
the screw.
• Mark,drill pilot hole and
fasten bottom screw.
screw head gap
• Reinstall Battery Cover.
(PERSONAL IDENTIFICATION NUMBER)
.
2
JKL
SECTION
FOR CONVENIENCE
FOR CONVENIENCE
DEF
1
GHI
4
Program
Button
Backlit Keypad
for Ease of Use
at Night
Battery
Compartment
9 Volt Battery
(included)
If Safety Reverse does not work properly:
1 Close Door and disconnect the Opener using Emergency Release Cord.
2 Do not use Door Opener, Remote Controls, or Wireless Keypad.
3 Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.
A Moving Door can cause serious injury or death.
1 Keep people clear of opening while Door is moving.
2 Do Not allow children to play with Wireless Keypad.
3 During programming, the Door Opener could begin to run, so stay away from
the moving Door and its parts. To keep the Door from moving, close the Door
and disconnect it from the Opener by pulling the Emergency Release Cord.
SECTION
BASIC PROGRAMMING FOR
1 ONE DOOR OPENER
Instructions
•
•
•
•
Interchangeable
Flip-up Cover
available in 3
optional Classic
Colors to match
your home’s
exterior decor
SEE NOTE AT BOTTOM OF SECTION 1
Proceed to Section 3 - Mounting Instructions.
).
This device complies with FCC Part 15 and RSS 210 of Industry Canada.This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are
designed to provide reasonable protection against harmful interference in a residential installation.This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: 1. Re-orient or
relocate the receiver antenna. 2. Increase the separation between the opener and receiver. 3. Connect the
opener into an outlet on a circuit different from that to which the appliance is connected. 4. Consult the dealer.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
Printed in the U.S.A.