Faucet Series
 Faucet Series Installation Guide Service Hotline Total Free 4000-999-075(China)
+1-408-867-8884(America) www.sumerain.com
Table of content 1. IMPORTANT INSTRUCTIONS
-----------------------------------------------------------
2. FA U C E T E X P L O S I O N - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
2
3
3. FA U C E T S I N S TA L L AT I O N - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
4. TROUBLESHOOTING --------------------------------------------------------------------9
5. CARE AND MAINTENANCE --------------------------------------------------------------11
For easy installation you will need to:
READ ALL the instructions completely before beginning.
READ ALL warnings, care, and maintenance information.
Purchase the correct water supply hook-up.
(1)Please check the accessories first.
(2)This instructions are typical faucet installation method as the reference guide, may differ from
your actual product. The installation steps still applied.
(3) We strongly advise to ask skilled plumber to install.
IMPORTANT INSTRUCTIONS [1] Operating Conditions
Recommended operating pressure
0.1~0.6Mpa
[2] Tools you may need when installing the faucet.
[3] Before You Begin
z
Shut off the main water supply.
z
If possible, install the faucet before installing the sink/lavatory.
z
Inspect the supply tubing for damage. Replace or clean if necessary.
FAUCET EXPLOSION
­ 1 ­ / 8 A1 FAUCET WITH ONE HOLE
Ⅰ
1
handle
2
faucet body
3
O-ring washer
4
Semi-circular rubber washer
5
Semi-circular metal-friction
6
mounting nutⅠ
7
mounting screw
8
hoses
Ⅱ
­ 2 ­ / 8 1
aerator
2
spout
3
handle
4
faucet body
5
O-ring washer
6
plastic washer
7
shank
8
mounting nut Ⅱ
9
hoses
A2 FAUCET WITH THREE HOLES
A3 FAUCET WITH FIVE HOLES
­ 3 ­ / 8 1 spout 2 O-ring washer 3 nipple 4 G 3/4” black washer 5 nut 6 washer ⅰ
7 triple tube 8 handle 9 decorate seat 10 washer ⅱ 11 washer ⅲ 12 nut 13 Ceramic cartridge 14 Triple valve 15 hoses
1
spout
2
O-ring washer
3
nipple
4
G 3/4” black gasket
5
nut
6
shunt valve
7
Shower hoses
8
handle
9
Decorate seat
10
washer ⅱ
11
washer ⅲ
12
nut ⅰ
13
Ceramic cartridge
14
Water inlet valve
15
shower
16
Shower sheath
17
washer ⅱ
18
washer ⅲ
19
nut ⅱ
20
21
20 cm hose
40 cm hose
A4 KITCHEN FAUCET
­ 4 ­ / 8 1
Faucet body
2
hose line
3
Spray head
4
handle
5
shank
6
washer ⅰ
7
washer ⅱ
8
nut
9
screw
10
cold water supply hose
11
hot water supply hose
12
weight ball
FAUCET INSTALLATION
A1.
Faucet with One Hole
Step 1: Begin installing your faucet by placing the O-ring washer and faucet in position on the
sink. Check the faucet and the O-ring washer position; make sure the base of the faucet is
parallel to the back of the sink.
Step2: From under the sink tighten the mounting nuts, making certain not to over-tighten which
could damage the nuts and make them difficult to remove in the future.
Step3: Screw on washers and mounting nuts. From underneath the sink, screw the
Semi-circular rubber washer and Semi-circular metal-friction and the mounting nuts onto the
mounting screw or shank (if it’s a shank), then tighter the mounting screw with a basin wrench.
Step4: Connect the water hoses to faucet shank, tighter the coupling nuts with a basin wrench.
Step5: Attach the faucet hoses. Attach the faucet hoses to the shutoff valves. Hand-tighten the
nuts, then give them extra quarter-turn with an adjustable wrench. To prevent damage to the
tubes, it’s a good idea to hold the valve with another wrench while you tighten them.
Step5:
All that left to do is turning the water on and check all the connections to ensure everything is
working correctly.
This assembly instructions can be used for one hole bathroom faucet, one hole kitchen
faucet, and one hole bidet faucet.
To the LED faucet with 4 batteries, the above five installation steps is applied, besides,
need to connect the supply line to the battery box at last.
A2 Faucet with three holes or five
Step1 Before installation ensure there are three (or five) Φ32~Φ35mm holes on the basin (or
bathtub), the faucet body’s bottom must put the O-ring; remove the faucet body bottom’s fixation
part.
Step2 Remove the handle, decorative seat from the control water body. Put the control water
body through the basin bottom (bathtub bottom), connect with the decorate seat and handle,
­ 5 ­ / 8 adjust the way and place, screw down the control water body’s lockup nut, make it fix on the
basin. At last install back the handle according to the remove step.
: The control water body with the red sign installs on the left and connects with hot water;
with blue sign install on the right and connects with cold water.
Step3 Put the O-ring wash under the faucet body, adjust the place, from under the basin, put on
the G 3/4” black washer, then screw on the nut, connect the triple tube to the nipple. Then
connect the two inlet hoses separate with the two control water body.
Step4 Two inlet hoses separate connect with the angle valve and two control water body, left
control water connect with hot water, right control water connect with cold water.
Step5 Open water source, check all connect point is leakage.
:
To the five hose bathtub faucet, connect the faucet body and the shower to the shunt
valve.
Warning:
1)
Water pressure must ensure more than 0.05 MPA.
2)
Must according left hot, right cold to connect.
3)
When using, open cold water first then open hot water.
A4 Pull out kitchen faucet
Please connect the150cm pull out water pile with the faucet head and add weight ball on the
pipe before you connect faucet with water supply. Other installation steps please reference to
A1.
A5 Wall Mount Faucet
1.
Refer to the faucet size, dig the faucet body conceal hole and cold, hot water pipe conceal
hole on the wall.
2.
Remove the spout, handle, cover and so on from the conceal body.
3.
Fix the inner wall, connect with cold, hot water pipe and open water source, confirm no
leakage.
4 Then cover spout, handle and other component according to the remove step to install back,
screw down screw to fix all component.
­ 6 ­ / 8 TROUBLESHOOTING
Symptom
Solution
Faucet leaks from
the handle
A.
B.
Tighten the packing nut
Replace the "O" ring or packing
A. Make sure the water supply valves under the sink are
The water pressure
turned on all the way
B. Clean or replace the aerator
is too low
C.
Check plumbing system for water pressure problems
The spout sprays
A.
Clean or replace the aerator
water all over
B.
Replace the aerator washer
Water is leaking
A.
Check the water supply connections to the faucet
from the faucet
B.
Inspect the water supply lines or hoses for leaks
A.
Remove the cap and tighten the screw
B.
Locate and tighten the hex set screw
C.
Remove the handle and check for stripped teeth on the
under the sink
Handle is loose
stem.
LED
does
not
illuminate
Insert new batteries or check the polarity of the batteries
check and the plug connection.
MAINTENANCE
■Clean the faucets and showers as and when required. Regular cleaning can prevent
calcification.
■Never use cleaning materials contain hydrochloric, formic, phosphoric or acetic acid, which
may cause considerable damage.
■Never use cleaning materials or appliances with an abrasive effect, such as unsuitable
cleaning powders, sponge pads, or micro fiber cloths.
■After cleaning, rinse thoroughly the faucet with clean water to remove any cleaner residue.
■Unscrew and clean the aerator regularly.
­ 7 ­ / 8 
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising