Installation Manual
Model: HILU75202
''
Ultra HD Interactive Flat Panel Display
QUICK SETUP GUIDE
For further information, see the User Manual. Moving and Carrying Notice
Please contact HITACHI directly if you
have questions on the use of the touch
monitor after reading the Installation Manual
and User Manual.
Important:
Please read the PRECAUTIONS, SAFETY
INSTRUCTIONS and this INSTALLATION
MANUAL carefully before installing
the touch monitor.
1 Precautions and safety instructions
Before using the touch monitor, please read this quick setup
guide thoroughly to help protect against damage to your own
and other people‘s property and ensure your own and other
people‘s personal safety.
Be sure to observe the following instructions.
For your safety, be sure to observe the warnings contained
in this guide.
For installation or adjustment, please follow this quick setup
guide and refer all servicing to qualified service personnel.
Safety Precautions
If smoke or a peculiar smell comes from the monitor, remove the
power plug from the socket immediately.
Failure to do so may result in fire or electric shock.
Contact your dealer for inspection.
If the monitor has been turned on but there isn’t a picture,
remove the power plug from the socket immediately.
Failure to do so may result in fire or electric shock.
Contact your dealer for inspection.
If water is spilled or objects are dropped inside the monitor,
remove the power plug from the socket immediately.
Failure to do so may result in fire or electric shock.
Contact your dealer for inspection.
If the monitor is dropped or the cabinet is damaged, remove the
power plug from the socket immediately.
Failure to do so may result in fire or electric shock.
Contact your dealer for inspection.
To turn off the power of the monitor completely, remove the
power plug from the socket
If the power cord or plug is damaged or becomes hot, turn off the
main power switch of the monitor, make sure the plug has cooled
down and remove the plug from the socket.
If the monitor is still used in this condition, it may cause a fire or
an electric shock. Contact your dealer for replacement.
2
Moving Notice:
Moving the monitor requires at least four people. If not, it may drop and a serious
injury may result.
Carrying Notice:
This monitor is heavy; please follow the instructions below when you are ready to
carry the monitor. Failure to do so may cause injury.
Installation
(when installing the monitor, please follow the instructions in this
quick setup guide)
Don‘t install in a high-temperature environment.
If the monitor is used in a high-temperature environment or in
direct sunlight, it may cause the case or other parts to become
distorted or damaged resulting in overheating or electric shock.
Don‘t install in a high-humidity environment.
This may cause overheating or electric shock.
Don‘t install near any heat sources such as radiators, hot-air
outlets, stoves, or other apparatus that produce heat.
This may cause a fire or electric shock.
Don‘t overload sockets or cables beyond electrical capacity.
Don‘t use extension leads as this may cause a fire or electric shock.
Don‘t insert the power plug into an socket other than 100~240V AC.
This may cause a fire or electric shock.
Don’t use a damaged power plug or worn socket.
Don‘t insert the wrong plug as it may cause a fire or electric
shock.
Do not place monitors on unstable shelves or surfaces.
They could collapse and cause damage.
Only install the unit on vertical, stable and level surfaces.
Don‘t place objects on the touch monitor.
If the touch monitor is covered or the vents are blocked, the
monitor could overheat and cause a fire.
If metal or liquid gets into the monitor, it may cause a fire
or an electric shock.
Do not place heavy objects on the monitor as they may fall
causing injury.
Please keep a minimum distance of 10 cm between the monitor
and the other objects for sufficient ventilation.
Don‘t move the touch monitor when it is connected to the power
cord and AV cables.
When moving the monitor, make sure you remove the plug
and cables from the socket or source.
When unpacking or carrying the monitor, at least 4 people
are needed. Make sure the monitor is carried upright.
Transport the monitor upright. Avoid placing the monitor
face up or face down.
Handle the monitor gently. Do not drop.
Wall mounting safety notes
1. Please make sure the bracket is fixed to a solid wall.
2 Package contents
Unpacking
The e-Screen is packed in a cardboard box and may be banded
to 2 types of custom pallet depending on the number of units
shipped. The e-Screen is packed using cushions to protect
the monitor during shipping.
Before unpacking your monitor, prepare a stable, level, and
clean surface near a wall socket.
Set the LCD Monitor box in an upright position and open
from the top of the box before removing the top cushions.
Step 1: Cut the banding.
Step 2: Remove the top cushion and take
the accessories box out.
Packing list
Item
1 Display
2 Carton
3 Bottom cushion
Q’ty
1
1
2
4 Top cushion
2
6 Accessories box
1
5 Packing bag
1
Contents of the Accessories box
2. After assembling, please don‘t pull or shake violently.
- Power cord black
- OSD Remote control (1.5V (AAA) battery included)
- USB cable
- User Manual
- Warranty Card
- HDMI cable
- Pen
3. Please don‘t install the bracket in direct sunslight or areas
of humidity / high temperature for fear that the quality
is affected.
4. Install the bracket at a minimum distance of 10 cm from other
objects / walls on either side. Only attach to vertical walls.
3
3 Installation
Power Input
Signal Source Input
Power Cord
The power cord, included, is used to connect the LCD monitor
and the wall socket.
Connect the power cord into main power socket of the monitor.
OSD 7Key
Power
Menu
In/Output Interface
6
7
8
Volume Down
▲
9
UP
▼
USB 2.0
5
Volume Up
Vol -
3
4
ON and OFF
PC, HDMI 1, HDMI 2, HDMI 3, DP
Vol +
RS232C
2
Display the main on-Screen Menu
Source
1
10
DOWN
11
12
13
14
15
16
17
18
19
Speaker out
USB 3.0
LAN Out
LAN In
D-SUB
Audio in (D-SUB)
SPDIF
Audio line out
LAN
Touch USB in
HDMI Out
DisplayPort
HDMI In 1
HDMI In 2
HDMI In 3
AC in socket (Input: 100-240V~ 50/60Hz)
Power Switch
RS232C
1
L(8Ω)
SPEAKER OUT
R(8Ω)
2
USB 3.0
4
LAN OUT
5
USB 2.0
LAN IN
D-SUB IN
PC AUDIO IN
SPDIF
LINE OUT
3
6
7
8
9
10
POWER
MENU
SOURCE
VOL +
VOL ▲
▼
POWER
AC IN
19
18
4
HDMI IN HDMI IN HDMI IN DISPLAY
3
2
1
PORT IN
17
16
15
14
HDMI OUT USB FOR
TOUCH
13
12
LAN
11
4 Operating the monitor
The control panel of the monitor
1
2
3
Remote Control
Receiver
1
2 3 4
1: LED Indicator
Power Status
Condition
Red
Power off(stand-by)
Blue
Off
Battery insertion
Power on
2 : USB
3 : Touch USB(for Laptop PC)
4 : HDMI IN (Connected to External)
AC off
Important Notice
The USB cable (5 m) that Hitachi provides in this accessory box is
for use of connection to Touch USB at the back. Therefore, in case
of connecting USB cable to Touch USB in front, separate USB cable
is required and the length of cable is strongly recommended to be
less than 3 m to make sure signal intensity of touch sensor work
properly.
Display Mode
Turning the monitor on
1. Correctly insert the power cord into the monitor and
into the power socket
2. Press the power button on the remote or front control panel.
The Remote Control (RCU) Instructions
Turning the monitor off
With the power on, press the power button on the remote or
front control panel to place the monitor in a standby mode. To
turn off power completely, disconnect the AC power cord from
the power outlet.
1
Adjusting the Volume
No. Function
Description
2
Navigates through submenus and
settings
3
Power
Source
▲, ◀, ▶, ▼
Menu
Exit
Freeze
Volume +
Volume Mute
Turns the monitor On and Off
Select source (PC, HDMI 1,
HDMI 2, HDMI 3 Displayport)
Open the menu
Closes the menu system
Freezes the current source image
Increases the sound volume
Decreases the sound volume
Turns off the sound
1. Using the remote, press the VOLUME+ or VOLUME- to increase
or decrease the volume.
2. Press the MUTE button to temporarily turn off all sound.
To restore the sound, press the MUTE button again.
Selecting the input source
1. Using the remote, press the desired source button (PC, HDMI 1,
HDMI 2, HDMI 3, DP)
2. Or press SOURCE on the monitor keypad, and toggle the source
button until you have reached the desired source, and press
ENTER
PC
HDMI 1
HDMI 2
HDMI 3
DP
3. If the monitor cannot find a source, a “No signal” message
will appear.
5
Touch Operation
No calibration is required for first-time use. However, the touch
system might need calibration over time or when for instance a
different resolution is used. Please find calibration instructions
below for the different operating systems:
Installation:
1. Connect the signal cable to the monitor and then turn on
the monitor.
2. Connect one side of the USB cable (type-B USB connector) on
the monitor side. (see “chapter 3, Signal Source Input”
for exact location)
3. Connect the other side of the USB cable (type-A USB connector)
to the computer.
4. Turn the computer on.
Wall
Windows 7&8 and Mac OSX
Wall bracket
Window system: No need to install the driver and calibration.
But if need to detail calibration or improve performance,
please install the driver.
MAC System: Should be install the driver.
Can not touch in state of not installing driver.
Windows 7&8 and Mac OSX Calibration Procedure
1. Install and run the “TouchWin” configuration program on the
computer.
2. Press “Calibration”.
3. A black screen with one green and eight white calibration points
appears.
4. Tap the green calibration point with yourfinger or Ergonomic
Stylus shortly.
5. The cursor will move to the next calibration point. Repeat
action 4 and move on to the next indicated calibration point.
6. Repeat action 4 until you get to the last calibration point in the
lower right-hand corner.
7. When you complete the nine-point calibration, a conformation
window appears. Click Done to accept the calibration; click
Cancel or do nothing (in which case the calibration window
automatically disappears after five seconds) to cancel the
calibration.
8. The front B-type USB is for laptop.
An usb is automatically converted when you connect a laptop.
The rear B-type USB is for PC.
An usb is automatically converted to laptop when you connect
a laptop and PC at the same time.
Remove the laptop USB if you want to use a PC.
Wall Mounting
Remove the wall mounting screw from the monitor.
The wall bracket (not included) is assembled with screws as shown
below. The fixing screws must be assembled carefully in the
screwed position.
6
Screw Machine M8 x 25㎜ (4PCS)
Wall bracket x 2 (Not Included)
5 Troubleshooting
Before calling service personnel, please check the following chart
for a possible cause to the trouble you are experiencing.
Perform the adjustments according to the instructions on the
„Operating the monitor page”
If the problem you have experienced isn’t described below
or you can’t correct the problem, stop using the monitor
and call service personnel or your dealer.
Problem
No Display
The image is not centered
Check these things
Ensure the power plug is
installed correctly at both ends.
Make sure the signal cable is
installed correctly at both ends.
Check that source equipment
is operating correctly.
Check if the input signal is compatible with this display.
Check if the input signal is
compatible with this display.
The image is not locked correctly Check if the input signal is
compatible with this display.
6 Compliance and regulatory information
FCC Compliance Statement:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used
in accordance with the quick setup guide and user manual, may
cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at their own expense.
Warning
This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions :
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
The remote control doesn’t work Make sure the batteries are new
and installed correctly.
Ensure the remote is aimed
at the IR sensor on the front
of the display
The picture color looks poor
Check the picture settings.
Reset the display.
7
">
