User Manual Coffee machine
coffee wakes up the world
User Manual
Coffee machine
English
01.06.01
Model Series 1200 Order number 33 2603 0010 Edition 01.2013

Congratulations on the purchase of your
WMF coffee machine.
The WMF 1200 S coffee machine is a fully automatic single
cup machine for espresso, café crème, cappuccino, milk
coffee, latte macchiato, milk foam and hot water. Hot Choc
beverages are also available as options.
Please read the User Manual prior
to using the coffee machine.
Each beverage is freshly brewed at the press of a button
which guarantees a high quality beverage.
The operator can control the coffee machine via the
two-line display.
Follow chapter 1 w User Manual
Signs and Symbols,
page 8.
Ensure that the staff has access to
the User Manual.
Important!
Observe the Safety chapter,
starting on page 63.
Observe the cleaning instructions
1200 S.
Please be sure to follow the instructions in the Start-up
Water filter, page 16 and make the
chapter w appropriate settings.
In the event of failure to comply
with maintenance information
(w Maintenance), no liability
is accepted for any resultant
damage.
Similarly, all guarantee / warranty
claims cease to apply in such
cases.
2
User Manual WMF 1200 S
Table of Contents
Table of Contents
Chapter 1
1.1
Introduction
6
Parts of the coffee machine
6
8
User Manual Signs and Symbols
Ready to operate
8
Glossary9
Chapter 2
Start-up
10
10
10
11
11
11
12
12
12
12
13
13
13
14
14
15
15
15
15
16
16
16
16
17
17
Chapter 3
Operation
18
18
18
19
19
20
20
20
21
21
22
22
23
23
Chapter 4
Settings
24
26
26
27
2.1Unpacking
Water tank
2.2
2.2.1 Insert water filter (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.2 Determine the water hardness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3 Fill the water tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3
Constant water supply (optional)
Drain connection
2.4
2.5
Grounds container
2.6
Connect up the milk
Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
With WMF milk cooler (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
With WMF milk cooler and Easy Milk (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7
Fill the bean hopper
Functional pads
2.8
Switch on coffee machine / start-up program
2.9
Switch off time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water hardness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SB mode (self-service mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start-up complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
4.1
4.2
Switch on the coffee machine
Beverage dispensing
Pot function for café crème
Warm rinsing
Milk and milk foam dispensing
Dispensing hot water
Height adjustment of the combi spout
Bean hopper / product hopper
Manual insert
Grounds container
Grounds disposal through the counter (optional)
Drip tray
Switch off the coffee machine
Cup volumes (cup size)
Dispensing test
Change recipes
User Manual WMF 1200 S
3
Table of Contents
4.2.1 Dispensing test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.2.2 Water volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.2.3 Ground coffee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.2.4 Milk foam volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.2.5 Latte macchiato pause interval. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2.6 Milk volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2.7 Sequence of dispensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2.8Pre-infusion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.3
Set grinding degree
30
4.3.1 WMF Perfect Extraction System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.4
Basic settings
32
4.4.1 Access basic settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.4.2Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.4.3 Switch off time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.4.4 Switch on time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.4.5 Milk foam quality (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.4.6 Topping quality (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.4.7Eco-mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.4.8 Boiler temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.9 Office functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.9.1 Second beverage level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.9.2 Milk beverages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.10Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.4.11Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4.12 Date / time (display). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4.13 Water filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4.14 Water hardness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4.15 Audio signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.4.16 SB mode (self-service mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.4.17 Display contrast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.4.18Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.4.19 PIN entry and PIN protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.5Counters
39
4.6Information
40
4.6.1 Software version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.6.2 Device name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.6.3 Machine number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.6.4 Date of production . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.6.5 Idle current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 5
Other settings
41
Mechanical settings
41
5.1.1 Set grinding degree. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Labelling of beverage buttons
41
5.2
5.1
Chapter 6
6.1
6.2
6.3
Care
Cleaning intervals overview
Care programs overview
Daily cleaning
6.3.1 Cleaning program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.2 Milk system cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Milk system cleaning Standard
Milk system cleaning Easy Milk
Milk system cleaning Plug&Clean
4
42
42
43
44
44
44
44
45
45
User Manual WMF 1200 S
Table of Contents
6.3.3 Mixer rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.4 Combi spout cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.5 General cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4
Weekly cleaning
6.4.1 Choc / Topping mixer cleaning (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.2 Water tank cleaning (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5
Regular cleaning
6.5.1 Brewing unit cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.2 Bean hopper cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.3 Product hopper cleaning (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6
Filter change
6.7Descaling
6.7.1 Descaling coffee machine with constant water supply. . . . . . . . . . . . . . . . . . . . . . .
6.7.2 Descaling coffee machine with water tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
45
45
46
46
46
47
47
48
49
50
50
51
52
Chapter 7
HACCP cleaning schedule
54
Chapter 8
Maintenance
56
56
57
Chapter 9
Messages and instructions
58
58
58
58
58
58
58
59
59
59
59
59
60
61
8.1
Coffee machine maintenance
8.2WMF Service
9.1
Operating messages
9.1.1 Empty grounds container. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1.2 Grounds container missing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1.3 Fill the water tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1.4 Empty drip tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1.5 Bean hopper is empty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1.6 Insert ground coffee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1.7 Clean the coffee machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1.8 Change filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1.9 Descale coffee machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2
Error messages and malfunctions
9.2.1 Error messages on the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2.2 Errors without error message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.1 Hazards to the operator
10.2 Hazards to the coffee machine
10.3 Intended use
10.4Directives
10.5 Duties of the owner / operator
10.6 Warranty claims
No warranty is provided:
Chapter 10 Safety
63
63
65
65
66
67
68
68
Overview of additional instructions
69
Technical data for coffee machine
Conditions for usage and installation
Technical data
70
70
70
Accessories and spare parts
72
Index
74
User Manual WMF 1200 S
5
Introduction
Chapter 1 Introduction
1.1
Parts of the coffee machine
1
2
2
3
1
2
4
5
10
6
11
7
13
12
8
9
4
your selection pls
08:15
09.01.2013
14
6
15
16
17
18
User Manual WMF 1200 S
Introduction
1
Bean hopper (optional 1 or 2)
2
Manual insert / tablet insert
3
Choc hopper / Topping hopper (optional)
4
Display
5
Beverage buttons
6
Height-adjustable combi spout to dispense beverages
7
Cover / Easy Milk (optional)
8
Grounds container
9
Removable drip tray with drip grid
10 Hot water button
11 ON/OFF switch (on the bottom of the front panel)
12 Water tank (coffee machines without a constant water supply)
13 Brewing unit
Display and functional pads
14 C pad
15 Care pad
16 P pad
17 Minus pad
18 Plus pad
User Manual WMF 1200 S
7
Introduction
User Manual Signs and Symbols
Caution.
Hazards to the
machine.
Follow the manual.
Caution.
Hazards to the user.
Observe the Safety chapter.
Caution.
Hot liquid.
Observe the Safety chapter.
Caution.
Hot surface.
Observe the Safety chapter.
Caution.
Bruising or crushing
hazard.
Caution.
Hot steam.
Observe the Safety chapter.
Observe the Safety chapter.
Caution.
Slipping hazard.
Tip
Instructions
Observe the Safety chapter.
Cross reference
Ready to operate
The descriptions in the User Manual always assume that
the coffee machine is ready to operate.
your selection pls
08:15
09.01.2013
8
User Manual WMF 1200 S
Introduction
Glossary
Term
Explanation
•
• Listings, selection options
™™
™™ Individual steps
Text in italics
Description of coffee machine state and/or
explanations of automatic steps.
Beverage dispensing
Dispensing coffee, hot water or Choc beverages
Capacity
Carbonate hardness
For example the capacity of the water filter in litres
of water it can filter
Quoted in °dKH. The water hardness is a measure of
the calcium dissolved in the water.
Choc
Hot chocolate
Mains tap
Water stop valve, angle valve
Milk system
Combi spout, milk nozzle and milk hose
Mixer system
Complete module, mixer with portion controller for
Choc / Topping
O-rings
Seals
Pre-infusion
Pressing
Prior to brewing cycle, coffee is briefly infused
in order to ensure a more intense release of its
aromatic substances.
Automatic pressing of ground coffee prior to
brewing cycle.
Rinsing
Intermediate cleaning
SB mode (self-service mode)
Self-service customer operation
Topping
Milk powder
WMF Perfect Extraction System
Program for the perfect grinding degree setting
User Manual WMF 1200 S
9
Start-up
Chapter 2 Start-up
(For initial start-up after delivery from the factory)
Please refer to WMF 1200S User Manual, pay special
attention to the hazard notices and Safety chapter.
Caution.
Follow the manual.
Observe the Safety chapter.
Do not loosen any screws and do not remove any housing
part. The voltage inside the coffee machine is a hazard
to life.
Power connection and conditions for installation
starting on page 70
Technical data w Warning.
Risk of electrocution.
Risk to life if not observed.
Follow the manual.
Observe the Safety chapter.
• Packaging material in the box contains accessories. Do
not throw away.
• Make sure that the coffee machine is intact. In case of
doubt, do not start up the coffee machine, and inform
the WMF Service.
• Retain the original packaging in the event of any
subsequent return.
2.1
Unpacking
™™ Unpack the WMF 1200 S and place it on a stable,
horizontal surface
2.2
Parts of the machine
page 6
Technical data
w starting on page 70
Water tank
™™ Remove water tank, remove lid
™™ Take out any accessory components contained
10
User Manual WMF 1200 S
Start-up
2.2.1 Insert water filter (optional)
Instructions
™™ Remove the in-built water sieve from the water tank [1]
Be sure to keep the drain screen.
™™ Place the water filter adapter onto the water tank
coupling from above (with lock open) and lock into
place [2]
™™ Unpack the water filter and insert into the water filter
adapter [3]
1
2
If the water hardness is between
0 and 4 °dKH, no water filter is
needed.
w Start-up program
page 16
3
2.2.2 Determine the water hardness
™™ Request water hardness reading from water supplier,
or determine using WMF carbonate hardness test
(complete with instructions) in the accessories
The unit used is the “Deutsche Karbonathärte” = °dKH
2.2.3 Fill the water tank
™™ Rinse out the water tank and fill it with clean cold
drinking water
™™ Place lid on water tank and insert the water tank until
it stops
User Manual WMF 1200 S
11
Start-up
2.3
Constant water supply (optional)
™™ Carefully insert the seals attached to connecting tube
™™ Connect the rear connection of coffee machine and the
on-site water tap or water filter with the connecting
tube
Read and follow water filter instructions.
™™ Check connections for leaks and tighten if necessary
™™ Turn on water
2.4
Drain connection
™™ Push drain tube with angle piece onto water drain
connection onto rear of machine
™™ Connect drain tube to mains drain via an S-trap
Tube must not sag.
™™ Shorten hose if necessary
2.5
Grounds container
™™ Push combi spout all the way up
™™ Remove the grounds container and any accessories
™™ Insert the grounds container until it stops
2.6
Connect up the milk
Use a suitable milk nozzle on the combi spout.
• orange milk nozzle
= with a cooler, milk temperature 4–8 °C
* light blue milk nozzle
• green milk nozzle
= milk temperature 8–16 °C
* white milk nozzle
* Alternative milk nozzles, depending on the milk types used.
12
User Manual WMF 1200 S
Start-up
Standard
™™ Insert the milk nozzle into the milk connection on the
combi spout
™™ Feed the milk hose through the left side cover of the
machine
™™ Open the milk pack
™™ Insert the milk hose with the beige milk nozzle into the
milk pack
The hose must not be under tension or bent when
adjusting the height of the combi spout.
Standard version
With WMF milk cooler (optional)
™™ Insert the milk nozzle for cooled milk into the milk
connection on the combi spout
™™ Remove the milk container out of the milk cooler
™™ Push the milk container lid back
™™ Pour milk into the milk container
™™ Place the lid back on the milk container
™™ Feed the milk hose through the left side cover of the
machine into the cooler
™™ Insert the adapter on the milk hose into the connection
in the milk container lid
™™ Replace the milk container carefully
The milk hose is inserted into the adapter.
Milk cooler version
Milk cooler milk container
With WMF milk cooler and Easy Milk (optional)
™™ Insert the milk nozzle for cooled milk into the milk
connection on the combi spout
™™ Screw the milk hose adapter onto the Easy Milk
connection
™™ Fill the milk container in the milk cooler with milk
w User Manual milk cooler
Milk cooler adapter
Easy Milk connection
User Manual WMF 1200 S
13
Start-up
2.7
Fill the bean hopper
™™ Remove the lid
™™ Fill with coffee beans
™™ Lock the lid
Ensure that no foreign objects land in the bean hopper.
Such foreign objects can damage the grinders. This
damage is not covered under the warranty.
2.8
Follow the manual.
Observe the Safety chapter.
Functional pads
C pad
• Cancel operation / entry
• Cancel beverage dispensing
• Free flow milk foam dispensing
(by pressing and holding)
Care pad
• Start warm-up rinsing
(press and hold for > 2 seconds)
• Access care and cleaning programs
P pad
• Access programs
• Confirm selection
Minus pad
• Step back
• Reduce value
• Reduce coffee strength (mild)
• Select cup size (-25 %)
Plus pad
• Step forward
• Increase value
• Increase coffee strength (strong)
• Select cup size (+25 %)
14
User Manual WMF 1200 S
Start-up
2.9
Switch on coffee machine /
start-up program
™™ Press the ON/OFF switch
Coffee machine switches on.
The start-up program starts.
language: english
OK: P
change: -/+
your selection pls
08:15
09.01.2013
The language used in
the display is set here.
The start-up program provides a step‑by‑step guide
through the remaining start-up steps on the display.
Follow the display instructions.
initial set-up
of your WMF 1200 S
This message is displayed for 5 seconds. The software
then provides a guide through the initial settings.
Switch off time
sw. off time: 0 min
OK: P
change: -/+
If the switch on time is activated, the
coffee machine switches on again at the
set switch on time.
Automatic switch off time in minutes after the last
beverage dispensing.
If set to 0 min , the coffee machine does not switch
off.
™™ Confirm the desired setting with
Time
time
OK: P
hh:mm:ss
change: -/+
The current time.
hh = hour (two places)
mm = minutes (two places)
ss = seconds (two places)
™™ Confirm the desired setting with
dd.mm.yyyy
change: -/+
The current date.
dd = day (two places)
mm = month (two places)
yyyy = year (four places)
™™ Confirm the desired setting with
Date
date
OK: P
User Manual WMF 1200 S
15
Start-up
Water filter
water filter:
no
OK: P
change: -/+
If water filter is set to yes , the filter should be rinsed
after the SB mode display.
Insert water filter
w p age 11
Water hardness
water hardn.:
20
OK: P
change: -/+
Carbonate hardness test
w Accessories included
... with water tank filter, or with no filter
The hardness of the drinking water being used.
Enter the result of the carbonate hardness test here.
™™ Confirm the desired setting with
Capacity
capacity: x
OK: P
change: -/+
... with constant water supply and water filter
The capacity of the water filter is set here.
(The capacity of the water filter can be found in the
water filter documentation.)
™™ Confirm the desired setting with
SB mode (self-service mode)
SB mode: no
OK: P
change: -/+
PIN entry and PIN protection
w p age 38
insert filter
OK: P
Insert water filter
w p age 11
place 3L container
under spout
16
When set to yes , the functional pads are not
displayed. The functional pads are displayed again
by touching and holding (at least 3 seconds) the
unilluminated P pad.
The SB mode function can be protected by a PIN.
... with water filter
™™ Place the water filter
™™ Touch
to confirm that the filter has been
inserted
™™ Place a collection container with approx. 3 litres
capacity under the combi spout
When rinsing the filter, you will hear unusual noises.
This is normal.
The noises will end during the filter rinse.
User Manual WMF 1200 S
Start-up
heating up ...
... all coffee machines
Coffee machine heats up.
A warm-up rinsing follows the heating-up process.
This warms up all the pipes.
After each brewing cycle, in the heating up phase and
during the care programs, release water runs into the
drip tray.
™™ Place a collection container with 120 ml capacity
under the combi spout
The warm-up rinsing lasts approx. 40 seconds.
Start-up complete
your selection pls
08:15
09.01.2013
A brewing test is performed following the end of the
start-up program.
The espresso button flashes.
™™ Place a suitably sized cup under the combi spout
™™ Press the flashing beverage button
Brewing test starts.
The coffee grinder will be filled with coffee beans
during the brewing test.
™™ Discard this first cup of coffee
The coffee machine is now ready for use.
Start-up is complete. All settings can be changed
now, or at a later time.
Set the automatic switch off time
w B asic settings
page 32
Setting options
•
•
•
•
Cup volumes (cup size) w page 26
Change recipes w page 27
Set grinding degree w page 30
Basic settings w page 32
User Manual WMF 1200 S
17
Operation
Chapter 3 Operation
A display-guided start-up program helps perform initial
start-up after delivery from the factory.
3.1
Switch on the coffee machine
™™ Switch on the coffee machine using the ON/OFF switch
Coffee machine switches on and heats up.
An automatic warm rinsing starts.
When the coffee machine is ready to dispense beverages,
the “Ready to operate” display appears.
3.2
Initial start-up
w Start-up
page 10
Change PIN
w Settings
w B asic settings
page 38
Set the switch on and switch off
times
w Settings
w B asic settings
page 32
Beverage dispensing
Pressing the beverage buttons triggers dispensing of the
beverage selected.
• Lit up button
= ready to dispense
• Flashing button =
beverage dispensing
• Unlit button
not ready to dispense /
button disabled
=
™™ Place a suitably sized cup under the combi spout
™™ Press the desired beverage button
Desired beverage is indicated on the display.
Caution.
Hot liquids in the
dispensing area.
Observe the Safety chapter.
Cancel beverage dispensing
™™ Touch
Second beverage level (optional)
When the second level is activated:
™™ Briefly press the beverage button twice
The beverage on the second level is initiated.
18
Office functions
w Settings
w B asic settings
page 35
User Manual WMF 1200 S
Operation
3.3
Pot function for café crème
Use the pot function to dispense several cups of café
crème at once.
™™ Touch and hold
for longer than 2 seconds
™™ Touch
twice
select beverage
pot of Café crème
and
are lit up.
Only
™™ Touch
Coffee machines with water tank
Water tank full?
OK: P
™™ Touch
place pot beneath
OK: P
™™ Place a suitably sized pot under the combi spout
™™ Confirm with
Preselect the number of cups (8, 6, 4, or 2 cups)
™™ Use
to scroll to the desired number of cups
™™ Touch
and start coffee dispensing
3.4
Warm rinsing
™™ Touch and hold
for longer than 2 seconds
warm rinse
in progress
Recommended after a longer
brewing pause, especially before
dispensing a cup of espresso.
A warm rinsing of the pipes with hot water starts.
The water warms the brewing system and guarantees an
optimum coffee temperature.
User Manual WMF 1200 S
19
Operation
3.5
Milk and milk foam dispensing
Milk (optional)
™™ Press the beverage button assigned to milk
Dispensing occurs.
Milk foam
™™ Touch and hold
Dispensing occurs. Dispensing continues for as long as the
pad is held.
3.6
Dispensing hot water
™™ Press the hot water button
Dispensing occurs.
If less water is required than the pre-set dispense amount,
dispensing can be stopped by pressing the hot water
button again.
Caution.
Hot surfaces.
Burn hazard.
3.7
Height adjustment of the combi spout
The combi spout is height adjustable.
™™ Take the combi spout from the front and push to the
desired height
Clearance height: 59–169 mm
20
User Manual WMF 1200 S
Operation
3.8
Bean hopper / product hopper
• If possible, refill product hopper in advance.
• Fill the hoppers no more than the amount needed
for one day, in order to maintain the freshness of the
products.
Coffee beans into bean hopper,
Choc powder into Choc hopper.
3.9
Manual insert
The manual insert is located in the centre of the coffee
machine cover.
Manual insert is used:
• For inserting cleaning tablets
• When using additional ground coffee types, such as
decaffeinated coffee
Add ground coffee or cleaning tablet only after the
display message.
Follow the manual.
Observe the Safety chapter.
Preparation using the manual insert
™™ Place a suitably sized cup under the combi spout
™™ Open manual insert lid
The display shows:
insert ground coffee
select beverage
™™ Insert ground coffee (max. 16 g)
™™ Close manual insert lid
™™ Press the desired beverage button
to cancel the process.
Touch
User Manual WMF 1200 S
Manual insert
21
Operation
3.10 Grounds container
The grounds container receives the used coffee grounds.
The display shows a message as soon as the grounds
container needs to be emptied.
Beverage dispensing is blocked for as long as the grounds
container is removed.
™™ Push combi spout all the way up
™™ Remove grounds container
™™ Empty and replace grounds container
™™ Confirm process on the display
Clean daily
w Care
page 44
If grounds container cannot be replaced, check chute for
coffee residue and remove.
Always empty grounds container before replacing.
Replacing without emptying results in the grounds
container being overfilled. The coffee machine will
be soiled. This may cause subsequent damage to the
machine.
Follow the manual.
Observe the Safety chapter.
3.11 Grounds disposal through the counter
(optional)
The coffee machine can be fitted with grounds disposal
through the counter. In this case, both the grounds
container and the coffee machine base have an opening
that passes through the on-site counter on which the
machine is placed. The spent coffee grounds are collected
in a large container under the counter.
22
Grounds disposal through the
counter is available as a retrofit kit.
Clean coffee grounds chute daily
w Care
page 45
User Manual WMF 1200 S
Operation
3.12 Drip tray
For coffee machines without a drain connection, the drip
tray must be emptied regularly.
™™ Remove the drip tray carefully, empty it, and then
reinsert the drip tray
On coffee machines with a drain connection the drip tray
may also be removed (e.g. for cleaning). Replace carefully
so that no water accidentally drips down.
Caution.
Hot liquids.
Move the drip tray
carefully.
Observe the Safety chapter.
Clean drip tray daily
w Care
page 45
3.13 Switch off the coffee machine
The coffee machine must be cleaned daily prior to
switching it off.
™™ Press the ON/OFF switch for longer than 2 seconds until
coffee machine switches off
™™ Disconnect mains plug
Coffee machines with a constant water supply
™™ Turn off main water supply tap
We do not accept any liability for damage resulting from
failure to observe this requirement.
Follow the manual.
Observe the Safety chapter.
User Manual WMF 1200 S
23
Settings
Chapter 4 Settings
Access settings
™™ Briefly touch
select program
browse: -/+
Chapter 4.1
Chapter 4.2
Chapter 4.3
cup volumes
OK: P
browse: -/+
change recipes
OK: P
browse: -/+
set grinding degree
OK: P
browse: -/+
cup volumes
select beverage
water volume: 37 ml
OK: P
change: -/+
brewing test
test grinding degree
coffee strength: 86%
OK: P
change: -/+
min.
foam volume: 14 sec
OK: P
change: -/+
grinding degree OK
test: P
end: C
Beverage button
cup volume: 100%
OK: P test: beverage
pressure
max.
macchiato pause: 20s
OK: P
change: -/+
milk volume: 14sec
OK: P
change: -/+
first coffee
OK: P
change: -/+
preinfusion: on
OK: P
change: -/+
24
User Manual WMF 1200 S
Settings
Chapter 4.4
Chapter 4.5
Chapter 4.6
basic settings
OK: P
browse: -/+
counters
OK: P
browse: -/+
information
OK: P
browse: -/+
language: english
OK: P
change: -/+
espresso 269
browse: -/+
V0.0x dd.mm.yyyy
browse: -/+
sw. off time: 0 min
OK: P
change: -/+
switch on time:hh:mm
OK: P
change: -/+
etc. all beverages
reset all counters?
No: C
Yes: P
WMF 1200S Basic
browse: -/+
serial no. ######
browse: -/+
foam quality 100%
OK: P
change: -/+
prod. date: mm.yyyy
browse: -/+
topping quality xxx
OK: P
change: -/+
empty current gr#:50
browse: -/+
ECO-mode: 0
OK: P
change: -/+
boiler temp.:
96°C
OK: P
change: -/+
office functions
OK: P
change: -/+
time
OK: P
hh:mm:ss
change: -/+
date
OK: P
dd.mm.yyyy
change: -/+
date / time: on
OK: P
change: -/+
water filter:
no
OK: P
change: -/+
water hardn.:
20
OK: P
change: -/+
audio signal:
on
OK: P
change: -/+
SB mode: no
OK: P
change: -/+
display contrast
OK: P
change: -/+
backup: no
OK: P
change: -/+
change PIN
OK: P
change: -/+
User Manual WMF 1200 S
25
Settings | Cup volumes (cup size)
4.1
Cup volumes (cup size)
The coffee machine adjusts the recipe quantities to the
new cup volume.
™™ Briefly touch
select program
browse: -/+
™™ Browse with
to
cup volumes
select beverage
™™ Select the cup volumes program with
™™ Select the beverage for which the cup volume should be
adjusted to the cup size
and .
Adjust the cup volume with
The cup volume is displayed in %. 100 % corresponds to
the beverage setting.
™™ If necessary, the new setting can be tested with
a dispensing test
cup volume: 100%
OK: P test: beverage
™™ As soon as the cup volume is set as desired, confirm
with
Dispensing test
™™ Press the desired beverage button
The beverage is dispensed using the newly changed values.
Each beverage setting can be tested during setup.
26
User Manual WMF 1200 S
Settings | Change recipes
4.2
Change recipes
Here you can adjust the recipes of your coffee specialties
according to your personal tastes.
The following settings are available:
• Water volume
• Ground coffee
• Milk foam volume *
• Latte macchiato pause interval
• Milk volume *
• Sequence of milk and coffee dispensing *
• Pre-infusion (aroma development)
* Option only available for beverages with milk
Adjustments can be made only to
the additions that are available for
this beverage.
Example: for cappuccino, this is
milk foam only
4.2.1 Dispensing test
™™ Press the desired beverage button
The beverage is dispensed using the newly changed values.
Each beverage setting can be tested during setup.
™™ Briefly touch
select program
browse: -/+
™™ Browse with
to
change recipes
OK: P
browse: -/+
™™ Select the change recipes program with
™™ Select the beverage for which the taste and
composition should be set
C pad
Cancel
Care pad
Warm rinsing
Cleaning
P pad
Programs
Menu control
Minus pad
Coffee strength
Setting the values
Preselect cup volume
Plus pad
Coffee strength
Setting the values
Preselect cup volume
The new values are saved when
you exit the program.
User Manual WMF 1200 S
27
Settings | Change recipes
4.2.2 Water volume
water volume: 37 ml
OK: P
change: -/+
™™ Example: touch
to 37 ml
until the water volume is increased
water volume: 37 ml
OK: P test: beverage
Each beverage setting can be tested during setup.
™™ Place a suitably sized cup under the combi spout
™™ Press the beverage button again
™™ Test the beverage
™™ As soon as the beverage is set as desired, confirm
with
water volume: 37 ml
OK: P
change: -/+
4.2.3 Ground coffee
coffee strength: 86%
OK: P
change: -/+
The grinding quantity varies depending on the grinding
degree set, the type of coffee used, the humidity and
various other factors.
Determine the desired coffee strength with a dispensing
test.
™™ As soon as the beverage is set as desired, confirm
with
For espresso, the factory setting at
100 % corresponds to a grinding
time of 5.1 seconds.
Approximately 1,8 grammes of
espresso are ground per second.
4.2.4 Milk foam volume
Setting in seconds.
Only available for beverages with milk foam.
foam volume: 14 sec
OK: P
change: -/+
The milk foam volume depends on the milk used, the milk
temperature and the milk nozzle selected. Determine the
desired volume with a dispensing test.
28
Adjustments can be made only to
the additions that are available for
this beverage.
User Manual WMF 1200 S
Settings | Change recipes
4.2.5 Latte macchiato pause interval
Pause interval between dispensing milk and coffee.
macchiato pause: 20s
OK: P
change: -/+
™™ As soon as the beverage is set as desired, confirm
with
4.2.6 Milk volume
Possible only for latte macchiato.
Setting in seconds.
Only available for beverages with milk foam.
milk volume: 14sec
OK: P
change: -/+
The milk volume depends on the milk used, the milk
temperature and the milk nozzle selected. Determine the
desired volume with a dispensing test.
™™ As soon as the beverage is set as desired, confirm
with
4.2.7 Sequence of dispensing
Coffee first or coffee last.
first coffee
OK: P
change: -/+
Adjustments can be made only to
the additions that are available for
this beverage.
The setting for the sequence
of beverage dispensing is only
offered for beverages with milk
components.
Exception: latte macchiato
4.2.8 Pre-infusion
preinfusion: on
OK: P
change: -/+
Before brewing, the ground coffee is wetted with hot
water. This causes the ground coffee to swell up, enabling
the aroma of many types of coffee to develop better.
™™ As soon as the beverage is set as desired, confirm
with
User Manual WMF 1200 S
The pre-infusion function is set to
“on” at the factory for all coffee
beverages except café crème.
29
Settings | Set grinding degree
4.3
Set grinding degree
4.3.1 WMF Perfect Extraction System
™™ Briefly touch
select program
browse: +
™™ Place a collection container under the spout for the
warm rinse
™™ Browse with
to
set grinding degree
OK: P
browse: -/+
™™ Select the set grinding degree program with
An automatic warm rinse starts.
A brewing test starts immediately thereafter.
™™ Place a suitably sized cup under the combi spout
brewing test
test grinding degree
The brewing pressure is shown in the form of a bar
diagram during the brewing test.
• Low brewing pressure g coarse grinding degree
• High brewing pressure g fine grinding degree
min.
pressure
The Perfect Extraction System is
for the preparation of beverage
specialties containing espresso.
C pad
Cancel
Care pad
Warm rinsing
Cleaning
P pad
Programs
Menu control
Minus pad
Coffee strength
Setting the values
Preselect cup volume
Plus pad
Coffee strength
Setting the values
Preselect cup volume
The new values are saved when
you exit the program.
max.
After a few seconds, the grinding degree setting is shown
in the display:
Grinding degree ok
grinding degree OK
test: P
end: C
The brewing pressure is within the optimum range. No
further adjustment is necessary.
to end grinding degree setting
™™ Touch
30
User Manual WMF 1200 S
Settings | Set grinding degree
Grinding degree too coarse
grinding too coarse
test: P
end: C
™™ Turn the multitool clockwise to set the grinding degree
finer
Test the new grinding degree setting
™™ Place a suitably sized cup under the combi spout
™™ Briefly touch
Two new brewing tests start automatically, one after the
other.
The brewing pressure is shown in the form of a bar
diagram during the second brewing test.
• Low brewing pressure g coarse grinding degree
• High brewing pressure g fine grinding degree
After a few seconds, the grinding degree setting is shown
in the display.
to end grinding degree setting
™™ Touch
Set grinding degree
w p age 41
Bar diagram display
w p age 30
Grinding degree too fine
grinding too fine
test: P
end: C
™™ Turn the multitool counter-clockwise to set the grinding
degree coarser
™™ Test the new grinding degree setting (see above)
™™ Touch
to end grinding degree setting
User Manual WMF 1200 S
Set grinding degree
w p age 41
Set coffee strength
w p age 28
31
Settings | Basic settings
4.4
•
•
•
•
•
•
•
•
•
Basic settings
Language
Switch off time
Switch on time
Milk foam quality (optional)
Topping quality (optional)
ECO-mode
Boiler temperature
Office functions
Time
•
•
•
•
•
•
•
•
•
Date
Date / time (display)
Water filter
Water hardness
Audio signal
SB mode (self-service mode)
Display contrast
Backup
Change PIN
4.4.1 Access basic settings
™™ Briefly touch
select program
browse: -/+
™™ Browse with
to
basic settings
OK: P
browse: -/+
™™ Select the basic settings program with
The first setting option appears automatically. Browse to
the others by touching
4.4.2 Language
language: english
OK: P
change: -/+
C pad
Cancel
Care pad
Warm rinsing
Cleaning
P pad
Programs
Menu control
Minus pad
Coffee strength
Setting the values
Preselect cup volume
Plus pad
Coffee strength
Setting the values
Preselect cup volume
The new values are saved when
you exit the program.
™™ Touch
to set the desired language
™™ Confirm the desired setting with
4.4.3 Switch off time
sw. off time: 0 min
OK: P
change: -/+
Automatic switch off time in minutes after the last
beverage dispensing.
If set to 0 min , the coffee machine does not switch off.
™™ Confirm the desired setting with
32
Instructions
If timer operation is activated, the
coffee machine switches on again
at the set switch on time.
User Manual WMF 1200 S
Settings | Basic settings
4.4.4 Switch on time
switch on time:hh:mm
OK: P
change: -/+
Automatic switch on time for the coffee machine.
If set to off , the coffee machine will not be switched on
automatically.
When set to on , the time can be set using
and .
™™ Confirm the desired setting with
4.4.5 Milk foam quality (optional)
foam quality 100%
OK: P
change: -/+
Milk foam quality for all beverages with milk foam. Setting
used to compensate for variations in milk characteristics.
Reduce setting value -> finer foam and lower dispensing
temperature
Increase setting value -> greater foam level and higher
dispensing temperature
™™ Confirm the desired setting with
4.4.6 Topping quality (optional)
topping quality xxx
OK: P
change: -/+
Quality of Topping additive. This setting will apply
to all beverages with Topping. Variations in Topping
characteristics are compensated for with this setting.
Reduce setting value -> less powder in relation to the
amount of water
Increase setting value -> more powder in relation to the
amount of water
™™ Confirm the desired setting with
User Manual WMF 1200 S
33
Settings | Basic settings
4.4.7 Eco-mode
ECO-mode: 0
OK: P
change: -/+
The energy consumed by the coffee machine at its lowest
load can be reduced here.
™™ Confirm the desired setting with
ECOmode
0
1
Hot water boiler
For coffee beverages and hot water
Ready to operate: always, immediately.
Ready to operate: always, immediately.
Steam boiler
For milk beverages
Ready to operate: always, immediately.
Temperature is reduced 10 minutes
after the last beverage.
After the temperature has been
reduced, it must be heated up before
the next beverage is dispensed.
Heating duration approx. 15 seconds.
2
9
Temperature is reduced 10 minutes
after the last beverage.
Temperature is reduced 10 minutes
after the last beverage.
After the temperature has been
reduced, it must be heated up before
the next beverage is dispensed.
Heating duration approx. 15 seconds.
After the temperature has been
reduced, it must be heated up before
the next beverage is dispensed.
Heating duration approx. 15 seconds.
Temperature is reduced 10 minutes
after the last beverage.
Always switched off.
For dispensing pure coffee, without
milk beverages.
After the temperature has been
reduced, it must be heated up before
the next beverage is dispensed.
Heating duration approx. 15 seconds.
For coffee machines without a steam boiler, only ECO
modes 0 and 2 can be set.
34
User Manual WMF 1200 S
Settings | Basic settings
4.4.8 Boiler temperature
boiler temp.:
96°C
OK: P
change: -/+
Boiler temperature in °C (brewing water temperature).
(Standard setting 96 °C)
™™ Confirm the desired setting with
4.4.9 Office functions
office functions
OK: P
change: -/+
™™ Touch
4.4.9.1 Second beverage level
2nd level: yes
OK: P
change: -/+
When set to no , beverages from the second beverage
level are no longer available.
™™ Touch
4.4.9.2Milk beverages
milk beverages: yes
OK: P
browse: -/+
When set to no , beverages containing milk are no longer
available.
™™ Confirm the desired setting with
4.4.10 Time
time
OK: P
hh:mm:ss
change: -/+
The current time.
hh
= hour (two places)
mm = minutes (two places)
ss
= seconds (two places)
™™ Confirm the desired setting with
User Manual WMF 1200 S
35
Settings | Basic settings
4.4.11 Date
date
OK: P
dd.mm.yyyy
change: -/+
The current date.
dd
= day (two places)
mm = month (two places)
yyyy = year (four places)
™™ Confirm the desired setting with
4.4.12 Date / time (display)
date / time: on
OK: P
change: -/+
The display of time and date on the “Ready to operate”
display.
™™ Confirm the desired setting with
4.4.13 Water filter
water filter:
no
OK: P
change: -/+
Indicates whether a water filter is in use.
(recommended for water hardness of 5 °dKH and above)
™™ Confirm the desired setting with
Insert water filter
w p age 11
4.4.14 Water hardness
water hardn.:
20
OK: P
change: -/+
The hardness of the drinking water being used.
Enter the result of the carbonate hardness test here.
™™ Confirm the desired setting with
36
Carbonate hardness test
w Accessories included
User Manual WMF 1200 S
Settings | Basic settings
4.4.15 Audio signal
audio signal:
on
OK: P
change: -/+
™™ Confirm the desired setting with
4.4.16 SB mode (self-service mode)
SB mode: no
OK: P
change: -/+
When set to yes , the functional pads are not displayed.
Recommended for self-service.
™™ Confirm the desired setting with
The functional pads are displayed again by touching and
holding (at least 3 seconds) the unilluminated P pad .
4.4.17 Display contrast
display contrast
OK: P
change: -/+
Display contrast is set here.
™™ Confirm the desired setting with
4.4.18 Backup
backup: no
OK: P
change: -/+
Instructions
All individual settings are lost if
you reset to the factory settings.
If set to yes , all basic settings and all beverage settings
are reset to the factory settings.
™™ Confirm the desired setting with
User Manual WMF 1200 S
37
Settings | Basic settings
4.4.19 PIN entry and PIN protection
0
change PIN
OK: P
change: -/+
1
2
™™ Touch
to open the change PIN menu
Enter the PIN using the beverage buttons. The uppermost
button is 0, the second is 1, the third is 2, etc.
Initial PIN entry (activate PIN)
When shipped from the factory, the PIN is 00000 .
™™ Briefly press the uppermost beverage button five times
Each time it is pressed, a “zero” is entered and appears on
the display.
™™ Enter the desired PIN
PIN protection
The activated PIN affects the following functions.
• Counters
Counters can be cleared only after entering the PIN.
• When self-service mode is active, the functional pads
are deactivated (unilluminated.)
The functional pads can be activated again only after
the PIN has been entered.
3
4
5
Use beverage buttons to enter
the PIN
Counters
w p age 39
SB mode (self-service mode)
w p age 37
Activate the care pad with PIN protection
for longer than 3 seconds
™™ Touch and hold
The care pad is displayed again.
Deactivate PIN protection
™™ Enter the current PIN and set to 00000
38
User Manual WMF 1200 S
Settings | Counters
4.5
Counters
™™ Briefly touch
select program
browse: -/+
™™ Browse with
OK: P
to
counters
browse: -/+
You can display the number of beverages prepared here.
™™ Confirm the counter display with
™™ Use
to browse through the individual beverages
Example espresso:
espresso 269
browse: -/+
As soon as all beverages have been displayed the following
appears
reset all counters?
No: C
Yes: P
Keep counter settings
™™ Touch
User Manual WMF 1200 S
Counter reset can be protected
by a PIN.
PIN entry and PIN protection
w p age 38
Delete counters
™™ Touch
39
Settings | Information
4.6
Information
™™ Briefly touch
select program
browse: -/+
™™ Browse with
to
information
OK: P
browse: -/+
4.6.1 Software version
V0.0x dd.mm.yyyy
browse: -/+
The software version and date are shown.
4.6.2 Device name
WMF 1200S Basic
browse: -/+
The name and type of the device are displayed.
4.6.3 Machine number
serial no. ######
browse: -/+
The 6-digit machine number is shown.
4.6.4 Date of production
prod. date: mm.yyyy
browse: -/+
The date of production is shown.
4.6.5 Idle current
empty current gr#:50
browse: -/+
The idle current is displayed in digits.
40
User Manual WMF 1200 S
Other settings
Chapter 5 Other settings
5.1
Mechanical settings
5.1.1 Set grinding degree
™™ Remove bean hoppers
Preset grinding degree is now visible.
™™ Release coffee dispensing and wait until grinder starts
up
™™ With grinder running, alter grinding degree as desired
on the side of the coffee machine using the multitool
Left grinder
Grinding degree 1 g fine
Right grinder
Grinding degree 1 g fine
Grinding degree 6 g coarse
Grinding degree 6 g coarse
Bruising or crushing hazard.
Never reach into the grinders with coffee machine
running and bean hoppers removed.
5.2
Caution.
Bruising or crushing
hazard.
Observe the Safety chapter.
Labelling of beverage buttons
First switch off the coffee machine in order not to trigger
beverage dispensing inadvertently.
™™ Pull out existing labelling behind front glass in
a downward direction
™™ Write on label stickers as desired using the
WMF template
™™ Stick on label mount and re-insert behind the front
glass panel
The template can be printed out on adhesive labels or
paper.
Stick paper to label mount using an adhesive sticker.
Free download of WMF label
template from
www.servicecenter.wmf.com
Matching adhesive labels:
Zweckform-Avery No. 3659
User Manual WMF 1200 S
41
Care
Chapter 6 Care
Regular cleaning is essential in order to ensure
problem-free operation of the coffee machine and to
ensure optimum coffee quality.
Prior to and after every instance that the machine is shut
off for several days, perform all cleanings.
Caution.
Health hazard.
Follow the HACCP schedule.
6.1
Cleaning intervals overview
Message
Optional
Regularly
Weekly
Daily
Care
x
x
O Warm rinsing
Cleaning program
O Milk system rinsing
O Mixer rinsing
Milk system cleaning Standard
O Milk system cleaning Easy Milk
O Milk system cleaning Plug&Clean
Grounds container cleaning
Drip tray cleaning
Cover cleaning
O Mixer cleaning
O Water tank cleaning
Brewing unit cleaning
Bean hopper cleaning
O Product hopper cleaning
O Filter change
Descaling
x
x
x
x
x
x
x
x
x
x
(x)
x
x
x
x
x
Daily
= Daily, at least once per day and as required
Weekly
= Weekly cleaning
w p age 19
w Cleaning instructions
w p age 44
w p age 45
w p age 46
w p age 47
w p age 48
w p age 49
w p age 50
Regularly = Regularly as required
Message = After the display shows a message
Optional = Optional (depending on the model)
(x)
= Daily as required
42
User Manual WMF 1200 S
Care
6.2
Care programs overview
About the cleaning programs
™™ Briefly touch
select clean.program
browse: -/+
w Cleaning instructions
cleaning
OK: P
browse: -/+
switching off
OK: P
browse: -/+
cleaning
OK: P
browse: -/+
no switching off
OK: P
browse: -/+
milk system rinsing
OK: P
browse: -/+
for coffee machines without Plug&Clean
milk system cleaning
OK: P
browse: -/+
for coffee machines with Easy Milk
OK: P
Plug&Clean
browse: -/+
for coffee machines with Plug&Clean
mixer rinsing
OK: P
browse: -/+
filter exchange
OK: P
browse: -/+
w p age 50
machine descaling
OK: P
browse: -/+
Customer check up
OK: P
browse: -/+
w Customer Check-up Instructions
brewing unit change
OK: P
browse: -/+
User Manual WMF 1200 S
43
Care
6.3
Daily cleaning
For all cleaning programs, the combi spout, the milk
nozzle, and the milk hose must be installed.
6.3.1 Cleaning program
The cleaning program leads step by step through milk
system rinsing, the optional mixer rinsing and the machine
cleaning via software.
Caution.
Hot liquids in the
dispensing area.
Observe the Safety chapter.
Cleaning program
w Cleaning instructions
6.3.2 Milk system cleaning
Milk system cleaning w Cleaning instructions.
The milk system consists of:
• Combi spout
• Milk nozzle
• Milk hose
The milk system must be thoroughly cleaned and
sanitized at least once a day, after no more 24 hours.
For coffee machines with Plug&Clean, this must be done
as part of the machine cleaning at the end of operation.
If this Plug&Clean cleaning is not done, then the combi
spout must be disassembled and cleaned manually.
Caution.
Hot liquids in the
dispensing area.
Observe the Safety chapter.
Caution.
Follow the hygiene
instructions.
See HACCP schedule.
Milk hose should be changed at regular intervals.
Milk system cleaning Standard
Milk system cleaning consists of three parts.
• Automatic foamer rinsing 3 minutes after the last
beverage with milk or milk foam
• Display-guided milk system rinsing
• Once per day, place combi spout, milk hose and milk
nozzles in a cleaning solution
44
Combi spout cleaning
w Cleaning instructions
Milk system cleaning
w Cleaning instructions
User Manual WMF 1200 S
Care
Milk system cleaning Easy Milk
Milk system cleaning consists of three parts.
• Automatic foamer rinsing 3 minutes after the last
beverage with milk or milk foam
• Display-guided milk system cleaning
• Once per week, place combi spout, milk hose and milk
nozzles in a cleaning solution
Milk system cleaning Easy Milk
w Cleaning instructions Easy Milk
Milk system cleaning Plug&Clean
Milk system cleaning consists of three parts.
• Automatic foamer rinsing 3 minutes after the last
beverage with milk or milk foam
• Display-guided Plug&Clean cleaning
• Once per week, place combi spout, milk hose and milk
nozzles in a cleaning solution
Milk system cleaning Plug&Clean
w Cleaning instructions
6.3.3 Mixer rinsing
Mixer rinsing is an intermediate cleaning of the mixer.
Mixer rinsing is an integral part of the cleaning program.
Mixer rinsing
w Cleaning instructions
6.3.4 Combi spout cleaning
Thorough cleaning of the milk system. The exact procedure
of this manual cleaning is described in the cleaning
instructions.
Combi spout cleaning
w Cleaning instructions
6.3.5 General cleaning
Grounds container cleaning (grounds chute, optional)
™™ Empty grounds container and rinse under running
drinking water
™™ Clean with a clean, damp cloth
Drip tray, cover and front panel
™™ Clean the cold coffee machine using a damp cloth
™™ Wipe dry using a fine woollen cloth or chamois leather
Do not clean with scouring powders or the like.
There is a risk of causing scratches or scores.
Do not use any sharp cleaners or implements.
User Manual WMF 1200 S
Order numbers for the WMF care
program
w Accessories and spare parts
page 72
Switch off the coffee machine
before cleaning the front panel
to avoid a beverage being
accidentally dispensed.
Hazards to the
machine.
Follow the manual.
45
Care
6.4
Weekly cleaning
6.4.1 Choc / Topping mixer cleaning (optional)
Cleaning will be more frequent depending on powder
consumption.
™™ Press the ON/OFF switch for longer than 2 seconds until
coffee machine switches off
™™ Disconnect mains plug
™™ Pull off mixer hose from mixer to combi spout
™™ Turn stud on bayonet connector underneath the mixer
bowl counter-clockwise
Mixer bowl is released from the retaining catch.
The propeller for the mixer is now visible.
™™ The propeller can be cleaned with a cloth
™™ Dismantle two-piece mixer bowl
™™ Clean both parts of mixer bowl and mixer hose under
warm running drinking water
™™ Allow all parts to dry completely
™™ Re-assemble all parts
open
On re-assembly, all openings must face in the same
direction.
™™ Replace mixer bowl
™™ Turn stud on bayonet connector back clockwise
™™ Push mixer hose onto mixer bowl fitting again, and plug
in combi spout
™™ Replace milk lid
Ensure that mixer hose is replaced securely.
This is important, as otherwise hot water or hot
Choc / Topping beverage may escape.
Ensure that the spiral guide is
seated and the hose is not pinched.
Caution.
Scalding hazard.
Observe the Safety chapter.
6.4.2 Water tank cleaning (optional)
Thoroughly rinse water tank weekly with clear drinking
water.
46
User Manual WMF 1200 S
Care
6.5
Regular cleaning
6.5.1 Brewing unit cleaning
The brewing unit should be cleaned as required and at
regular intervals. Recommendation: weekly.
™™ Press the ON/OFF switch for longer than 2 seconds until
coffee machine switches off
™™ Disconnect mains plug
™™ Push combi spout all the way up
™™ Remove grounds container
™™ Remove the drip tray
Brewing unit is now fully accessible.
Caution.
Bruising or crushing
hazard.
Risk of injury.
Hold firmly, as the brewing unit can slip downwards.
Never use force. Danger of breakage.
Hazards to the
machine.
Follow the manual.
™™ With one hand, reach into the chute under the brewing
unit and release the retaining catch (illustration 1)
™™ Slowly guide the brewing unit downwards, tilt and pull
forward
™™ Remove the brewing unit and hold firmly (illustration 2)
Use the multitool from the accessories.
Illustration 1
™™ Turn the thread on the brewing unit head counterclockwise (illustration 3) until the wiper is in the
forward position
™™ Push the springs outwards over the edge and unlock
(illustration 4)
™™ Swing the insertion unit upwards
Illustration 2
Illustration 3
User Manual WMF 1200 S
47
Care
Never clean the brewing unit in a dishwasher and never
use any cleaner additives.
™™ Clean the brewing sieve under running drinking water
or with a cloth
™™ Remove coffee grounds residue using a paint-brush or
scrubber
™™ Rinse the brewing unit under running drinking water
™™ Dry the brewing unit with a cloth
Allow to dry completely before reinstalling in the coffee
machine.
Remove coffee grounds residue from the chute.
™™ Wipe out the coffee grounds forward or suck out using
a vacuum cleaner
Refit the brewing unit after it has been dried.
™™ Replace springs in insertion unit (illustration 4)
™™ Hold the pusher compressed and replace the brewing
unit in the chute against rear cover
™™ Push the brewing unit upwards until it engages in the
lock
™™ Insert the grounds container
™™ Replace drip tray
Hazards to the
machine.
Follow the manual.
Illustration 4
Brewing sieve
If the brewing unit cannot be replaced without
resistance: turn thread on the brewing unit head slightly
to the left or right with the multitool until the brewing
unit slides into the guide.
Never use force.
Hazards to the
machine.
Follow the manual.
6.5.2 Bean hopper cleaning
The bean hoppers should be cleaned as required and at
regular intervals. Recommendation: monthly.
™™ Press the ON/OFF switch for longer than 2 seconds until
coffee machine switches off
™™ Disconnect mains plug
™™ Release bean hoppers lock using multitool by turning in
a clockwise direction
open
48
close
User Manual WMF 1200 S
Care
™™ Lift bean hoppers out
™™ Completely empty bean hoppers and wipe out
thoroughly with a damp cloth
™™ Allow bean hoppers to dry completely
™™ Refill and replace bean hoppers
™™ Lock with the multitool by turning counter-clockwise
Never reach into the coffee grinders.
Never clean the bean hoppers in a dishwasher.
Caution.
Bruising or crushing
hazard.
Observe the Safety chapter.
6.5.3 Product hopper cleaning (optional)
Choc / Topping
Cleaning will be more frequent depending on powder
consumption.
™™ Press the ON/OFF switch for longer than 2 seconds until
coffee machine switches off
™™ Disconnect mains plug
™™ Unlock product hoppers with multitool by turning in
a clockwise direction
™™ Lift product hopper out and empty completely
™™ Unscrew union nut at front and rear
™™ Remove the dosing auger
Never clean product hoppers in the dishwasher.
™™ Thoroughly wipe out product hopper with a damp cloth
™™ Thoroughly clean individual dosing auger components
™™ Allow product hopper and individual components to dry
completely
open
close
Hazards to the
machine.
Follow the manual.
Portion controller with individual
parts of the dosing auger
User Manual WMF 1200 S
49
Care
™™ Re-assemble and replace the dosing auger and screw on
union nuts
Ensure correct orientation of discharge.
™™ Refill and replace product hopper
™™ Lock with the multitool by turning counter-clockwise
6.6
Filter change
Follow the water filter User Manual for a filter change.
After a filter change, perform a rinse as guided by the
display.
6.7
Descaling
The water hardness, the water flow, and whether a water
filter is used determine the schedule for descaling.
This point in time is calculated by the WMF 1200 S and
displayed.
Descaling is made up of the three segments preparation,
descaling, and rinsing.
Do not drink the descaling solution that comes out of the
combi spout during descaling!
Use only WMF Descaling Agent. Any other descaling
agent may cause damage to the coffee machine. No
liability is accepted for damage caused by the use of any
other descaling agent and guarantee / warranty claims
are not entertained.
Start-up
w Water filter
page 16
Total duration of descaling
approx. 40 minutes.
The procedure may not be
interrupted.
Caution.
Descaling agents are
irritants. Always follow
the instructions on the
package.
Observe the Safety chapter.
The following is needed for descaling:
• 2 bottles of WMF liquid descaling agent (0.75 litre each)
• 1 bottle of warm drinking water (0.75 litre)
• 5-litre collection container
(for coffee machines without drain connection)
Displays lead step by step through the program. Follow
the instructions.
The descaling procedure sequence is different for each
model.
• 6.7.1Descaling coffee machine with constant water
supply (Water supply from the utility line)
• 6.7.2 Descaling coffee machine with water tank
50
Caution.
Hot steam and
hot water.
Burn hazard.
Scalding hazard.
Observe the Safety chapter.
User Manual WMF 1200 S
Care
6.7.1 Descaling coffee machine with constant
water supply
Preparation
™™ Touch
™™ Touch
until the desired program is displayed
™™ Select the desired program with
™™ Remove the milk hose
™™ Turn off main water supply tap
™™ Remove and empty drip tray
™™ Replace drip tray
™™ Remove water tank
™™ Turn and remove seal plug on water tank coupling
counter-clockwise (flat screwdriver, see illustration
1 and 2)
™™ Mix the two bottles of liquid descaling agent in the
water tank with 1 bottle of warm drinking water
™™ If crystals have formed when stored below the freezing
point, stir until all crystals present in the liquid
descaling agent have dissolved
™™ Replace the water tank filled with descaling solution,
and confirm on the display
™™ Place a collection container with approx. 5 litres
capacity under the combi spout
Descaling
Descaling starts. Duration approx. 13 minutes.
™™ After descaling, carefully empty the collection container
™™ Replace the collection container
™™ Empty remaining descaling solution from water tank
™™ Rinse out the water tank and fill to the maximum line
with clean, cold drinking water
(see marking on the outside of the water tank)
™™ Insert the water tank
User Manual WMF 1200 S
Illustration 1
Illustration 2
Crystals may form in the liquid
descaling agent when stored.
The crystals must not enter the
coffee machine.
The ideal water temperature is
approx. 37 °C.
51
Care
Rinsing
Rinsing starts. Duration approx. 11 minutes. After the
initial rinsing from the water tank, the display requests
that the water supply be turned on again.
™™ Turn on main water supply tap
Leave the water tank in place. The water tank coupling is
rinsed for approx. 10 seconds from the mains supply.
Follow-up and additional rinse
Duration: approx. 11 minutes.
™™ Remove water tank and dry
™™ Turn and remove seal plug on water tank coupling in
a clockwise direction (flat screwdriver, see illustration
1 and 2)
™™ Insert the water tank
Subsequent rinses are from the mains supply.
After the final rinsing the steam boiler is heated up. The
hot water expands and finally exits briefly as steam.
As soon as the descaling procedure is finished, the “Ready
to operate” display appears.
Caution.
Hot steam.
Observe the Safety chapter.
your selection pls
08:15
09.01.2013
™™ Remove the collection container
™™ Re-install the milk hose
6.7.2 Descaling coffee machine with water tank
Preparation
™™ Touch
™™ Touch
until the desired program is displayed
™™ Select the desired program with
™™ Remove the milk hose
™™ Remove and empty drip tray
™™ Replace drip tray
™™ Remove water tank
™™ Remove the water filter, if fitted
™™ Mix the two bottles of liquid descaling agent in the
water tank with 1 bottle of warm water
52
User Manual WMF 1200 S
Care
™™ If crystals have formed when stored below the freezing
point, stir until all crystals present in the liquid
descaling agent have dissolved
™™ Replace water tank filled with descaling solution
™™ Place a collection container with approx. 5 litres
capacity under the combi spout
Descaling
Descaling starts. Duration approx. 13 minutes.
™™ After descaling, carefully empty the collection container
™™ Replace the collection container
™™ Empty remaining descaling solution from water tank
™™ Rinse out the water tank and fill to the maximum line
with clean, cold drinking water
(see marking on the outside of the water tank)
™™ Insert the water tank
Rinsing
Rinsing starts. Duration approx. 22 minutes.
™™ When requested, fill with clean, cold drinking water
(after about 11 minutes)
™™ Empty the collection container and place under the
combi spout
If a water filter is used, a message appears after the
process is complete, with a request to re-install the water
filter.
™™ Place the water filter
™™ Fill the water tank with clean cold drinking water
The water filter is rinsed briefly.
After the final rinsing the steam boiler is heated up. The
hot water expands and finally exits briefly as steam.
As soon as the descaling procedure is finished, the “Ready
to operate” display appears.
Crystals may form in the liquid
descaling agent when stored.
The crystals must not enter the
coffee machine.
The ideal water temperature is
approx. 37 °C.
Order numbers of the article
w Accessories and spare parts
page 72
Caution.
Hot steam.
Observe the Safety chapter.
your selection pls
08:15
09.01.2013
™™ Remove the collection container
™™ Re-install the milk hose
User Manual WMF 1200 S
53
HACCP cleaning schedule
Chapter 7 HACCP cleaning schedule
You are required by law to ensure that your customers are
not subject to any health hazards as a consequence of the
consumption of the food items you serve.
A HACCP cleaning schedule (Hazard Analysis Critical
Control Points) for risk identification and assessment is
required. You should carry out a risk analysis on your
premises. The aim of the analysis is to recognize and
pre-empt food hygiene hazard points. For this purpose,
monitoring and, where necessary, test procedures must be
established and implemented.
With correct installation, care, maintenance, and cleaning,
WMF coffee machines meet the requirements described
above. If care and cleaning of the coffee machine is
not carried out properly, dispensing milk beverages will
constitute a food hygiene hazard point.
Please observe the following points in order to comply
with the HACCP cleaning schedule:
“Food Hygiene Ordinance from
05.08.1997”
Use our HACCP cleaning schedule
for monitoring of regular cleaning.
Sanitize the milk system daily
• Follow the cleaning instructions for the milk system
contained in the cleaning instructions. This will ensure
that your system contains a minimum of bacteria at
commencement of operation.
Always commence operation with a freshly opened
cooled milk pack
• Original packaged UHT milk is usually free from harmful
bacteria. Always open a new cooled milk pack at
commencement of operation.
• Ensure absolute cleanliness when opening the milk pack.
Germs can be introduced from dirty hands or tools
when opening.
54
Recommendation:
only use UHT milk with a 1.5 % fat
content.
User Manual WMF 1200 S
HACCP cleaning schedule
Keep milk cool.
• Always have a new cooled milk pack handy.
• If cooling is not used during operation, then the milk
must be used up very quickly. Cool the milk occasionally
if needed.
• If little milk is used, cooled milk must be placed in the
refrigerator again during operation.
At commencement of operation
milk should be at approx. 6–8 °C.
WMF AG offers a range
of refrigeration options
(e.g., WMF countertop coolers).
Recommendation for Choc and Topping (optional)
Regularly clean the product hopper. See the instructions in
the Care chapter.
See chocolate / Topping manufacturer's instructions.
Caution.
Follow the hygiene
instructions.
See Care chapter.
HACCP cleaning schedule
Month
Year
Use only cooled UHT milk, to prevent health risks due to bacteria.
For Choc and Topping, use only products that have not exceeded their expiration date.
3a. Clean the foamer and change out the combi spout after 4 hours of
operation time (absolutely required for low number of dispense cycles,
or if milk is not cooled)
3b. Weekly mixer cleaning and regular product hopper cleaning
(Care chapter)
4. General machine cleaning
Cleaning steps
Time
1
2
3
Signature
4
Date
Date
Cleaning steps:
1. Run the cleaning program
w Cleaning instructions
2a. Milk foamer cleaning (combi spout)
w Cleaning instructions
2b. Daily mixer cleaning
w Cleaning instructions
1.
17.
2.
18.
3.
19.
4.
20.
5.
21.
6.
22.
7.
23.
8.
24.
9.
25.
10.
26.
11.
27.
12.
28.
13.
29.
14.
30.
15.
31.
Cleaning steps
Time
1
2
3
Signature
4
16.
User Manual WMF 1200 S
55
Maintenance
Chapter 8 Maintenance
Please observe that this is a professional industrial coffee
machine which needs regular maintenance and descaling.
Timing of descaling is calculated by the coffee machine
and depends on the degree of hardness of the local mains
water and whether or not a water filter is fitted.
The maintenance date is based on the degree of use of the
coffee machine and is shown on the display. The coffee
machine may continue to be operated after the message,
but Customer Care or contract maintenance should be
carried out promptly to ensure correct functioning and so
as to avoid any consequent damage.
8.1
Descaling w Software
w Care
page 50
Coffee machine maintenance
The following care or maintenance stages are provided:
• Descaling, may be undertaken by the user / operator.
Descaling w Software
w Care
page 50
• Customer Check-up after the display message; may be
undertaken by the user / operator.
Customer Check-up after the
display message see Customer
Check-up Instructions in Customer
Check-up Kit.
w Accessories and spare parts
page 72
• Maintenance after the display message; may only be
undertaken by trained personnel or by WMF Service, as
in this instance components affecting safety must be
replaced.
Service maintenance message
w Messages and instructions
page 58
• Revision after the display message; may only be
undertaken by trained personnel or by WMF Service, as
in this instance components affecting safety must be
replaced.
For other maintenance work and
repairs, please contact your local
WMF Service.
The telephone number can be
found on the address sticker on
the coffee machine and on the
delivery note.
56
User Manual WMF 1200 S
Maintenance
8.2
WMF Service
You can reach the WMF Service Center if the local service
point is not known.
WMF AG
Eberhardstraße
D - 73309 Geislingen (Steige)
User Manual WMF 1200 S
57
Messages and instructions
Chapter 9 Messages and instructions
9.1
Operating messages
9.1.1
Empty grounds container
empty grounds cont.
Grounds container is full
™™ Remove grounds container empty and rinse
under drinking water
™™ Wipe dry the grounds container
™™ Replace grounds container
™™ Confirm with
9.1.2 Grounds container missing
beverage sel. locked
grounds cont.missing
The grounds container is not inserted
™™ Replace grounds container
9.1.3 Fill the water tank
refill water tank
beverage sel. locked
refill water tank
The water tank is nearly empty
™™ Remove water tank and fill it with clean cold
drinking water
™™ Replace water tank
9.1.4 Empty drip tray
empty drip tray
The drip tray must be emptied
™™ Remove and empty drip tray
™™ Replace drip tray
9.1.5 Bean hopper is empty
refill beans
right
refill beans
left
58
There are not enough coffee beans in the bean
hopper
Grinding is interrupted.
™™ Pour coffee beans into the bean hopper
™™ Press the beverage button again
The grinding process continues and the additional
coffee required for the brewing cycle is ground.
The selected beverage is then brewed.
User Manual WMF 1200 S
Messages and instructions
9.1.6 Insert ground coffee
insert ground coffee
select beverage
The manual insert lid is open
™™ Insert ground coffee
™™ Close the manual insert
™™ Select the desired beverage with the beverage
button
to cancel the process. Ground coffee
Touch
that has already been inserted is removed via the
grounds container.
9.1.7 Clean the coffee machine
machine cleaning
OK: care pad
The coffee machine must be cleaned
Only the care pad is lit up.
™™ Perform a machine cleaning
w Cleaning instructions w Machine cleaning
9.1.8 Change filter
your selection pls
replace water filter
The water filter must be changed
™™ Change filter
w Care w Filter change, page 50
9.1.9 Descale coffee machine
your selection pls
descale machine
9.2
The coffee machine must be descaled
™™ Perform a descaling
w Care w Descaling, page 50
Error messages and malfunctions
Basic procedure on display of error messages or
malfunctions
Switch coffee machine off and then on again after a few
seconds. Repeat the process which led to the error. In
many cases, this eliminates the malfunction and you can
continue working.
If this is not successful
Find the displayed error message or error number in the
following error list and follow the action instructions.
If this does not rectify the error or if the error indicated is
not listed please call WMF Service.
User Manual WMF 1200 S
WMF Service
w p age 57
59
Messages and instructions
Some messages lead to blocking of individual functions.
You will notice this by the fact that the beverage button
illumination goes out. The beverage buttons that are still
illuminated can continue to be used.
Your WMF 1200 S is provided with a diagnostics program.
Any errors that occur are shown on the display. The error
messages listed may also be caused by an interruption to
the mains electricity supply.
9.2.1 Error messages on the display
Error
number
Error
description
Action instructions
-
The brewing unit is not inserted.
™™ Replace the brewing unit
™™ Switch off the coffee machine
™™ Clean the brewing unit
26
Insert the brewing
unit
Brewing unit lockup
current / brewing unit
stiff
Right grinder blocked
36
Left grinder blocked
6
w Care w Brewing unit cleaning, page 47
™™ Switch off the coffee machine
™™ Disconnect mains plug
™™ Remove bean hopper
™™ Turn grinder disk counter-clockwise using only
Multitool (square button) (see illustration)
™™ Replace the bean hopper
™™ Switch on the coffee machine
w Care w Bean hopper cleaning, page 48
If this occurs frequently:
™™ Set grinding degree one stage coarser
w Other settings w Set grinding degree, page 41
w Settings w Set grinding degree, page 30
88
Boiler:
over-temperature
Beverage dispensing temporarily blocked.
™™ Check that mains tap is on or that the water tank is
filled and inserted correctly
If error not remedied
™™ Switch off the coffee machine
™™ Clean the brewing unit
w Care w Brewing unit cleaning, page 47
™™ Switch on and try again
(Release follows when cooled down to normal temperature).
™™ Switch off the coffee machine, allow to cool and
switch on again
If error not remedied
™™ Switch off the coffee machine
™™ Call WMF Service
60
User Manual WMF 1200 S
Messages and instructions
Error
number
Error
description
Action instructions
161
Flow error:
during the brewing cycle
Between each of the following steps switch off the coffee
machine and on again. If error not remedied carry out the next
step.
™™ Check that mains tap is on or that the water
tank is filled and inserted correctly
™™ Clean the brewing unit
w Care w Brewing unit cleaning, page 47
™™ Set grinding degree coarser / reduce quality
w Settings w Set grinding degree, page 30
w Other settings w Set grinding degree, page 41
162
164
165
166
167
188
Flow error:
... when cleaning
... when dispensing hot water
... when dispensing Choc
... steam boiler infeed
... when descaling
Heater error
™™ Switch the coffee machine off and on again
(for error number 166, also allow the coffee
machine to cool off)
If error not remedied
™™ Check that mains tap is on or that the water
tank is filled and inserted correctly
™™ Switch off the coffee machine, disconnect
mains plug
™™ Call WMF Service
9.2.2 Errors without error message
Error pattern
Action instructions
No hot water dispensing
but water in grounds
container
No Choc dispensing but
water in grounds container
Choc portion controller
blocked, Choc dispensed
only with water
™™ Clean hot water spout
™™ Call WMF Service (coffee dispensing possible)
User Manual WMF 1200 S
™™ Do not use Choc dispensing
™™ Call WMF Service (coffee dispensing possible)
™™ Clean portion controller
w Care w Product hopper cleaning, page 49
™™ Empty powder
™™ Turn dosing auger manually until all powder is removed
™™ If necessary rinse with drinking water
™™ (Allow to) dry completely
61
Messages and instructions
Error pattern
Coffee dispensing on
the left / right differs
No milk foam / milk
output, but milk in milk
container
Action instructions
™™ Clean the combi spout
w Cleaning instructions
™™ Check whether the milk hose is kinked or squashed
™™ Re-route milk hose correctly
™™ Clean the combi spout
™™ Check whether milk nozzle is blocked
w Cleaning instructions
No milk or milk foam
dispensing
™™ Check whether milk cooler is iced
Milk aperture is clogged (Easy Milk)
™™ Unscrew the aperture from the
Easy Milk connection
™™ Clean the aperture thoroughly with
the small cleaning brush [1]
™™ Perform milk system cleaning
1
w Cleaning instructions Easy Milk
Milk foam incorrect,
temperature too cold
or too hot
™™ Change milk nozzle
- orange or light blue milk nozzle for cooled milk
- green or white milk nozzle for uncooled milk
™™ Clean the combi spout
w Cleaning instructions
If error not remedied
™™ Use another milk nozzle from the accessories
Pump runs
™™ Switch off the coffee machine and on again
continuously, water in If error not remedied
grounds container
™™ Call WMF Service
Water tank: assembly / ™™ Lightly smear the O-rings with WMF gasket grease
disassembly stiff
Choc / Topping hopper ™™ Manually turn the drive for the dosing auger at the portion
cannot be replaced
controller slightly in a clockwise direction
™™ Check whether Choc hopper is accidentally locked
Bean hopper cannot be ™™ Check whether bean hopper is accidentally opened
replaced
62
User Manual WMF 1200 S
Safety
Chapter 10 Safety
10.1 Hazards to the operator
At WMF, safety is one of the most essential product
features. The effectiveness of safety devices can only be
ensured if the following points are observed:
• Read the User Manual carefully prior to use.
• Do not touch hot machine components.
• Do not use the coffee machine if it is not working
properly or if it is damaged.
• Use the coffee machine only when it is completely
assembled.
• Built-in safety devices must never be altered.
• This device is not designed for persons (including
children) with limited physical, sensory, or mental
capabilities or who lack the required experience
and/or knowledge, unless they are supervised by
a person responsible for their safety or have received
instructions from them about how the device should be
used.
• Children should be supervised to ensure that they do
not play with the device.
Despite the safety devices, every coffee machine poses
hazard potential if incorrectly used. Please observe the
following instructions when using the coffee machine so as
to prevent injury and health hazards:
Scalding hazard.
When dispensing coffee, hot water and steam there is
hazard of scalding. Ensure that there is always a suitable
cup under the spout when dispensing beverages.
Caution.
Failure to follow safety
instructions can result
in death or serious
injury.
Follow the safety instructions.
Caution.
Hot liquids in the
dispensing area.
Scalding hazard.
Caution.
Hot steam.
Burn hazard.
Burn hazard.
The brewing unit must be cleaned only when the coffee
machine is cold. The brewing unit can get hot.
User Manual WMF 1200 S
Caution.
Hot surfaces.
Burn hazard.
63
Safety
Bruising or crushing hazard.
There is a bruising or crushing hazard when handling
all moving parts. Do not reach into the bean hopper or
the brewing unit opening when the coffee machine is
switched on.
Health hazard.
The product hoppers (coffee beans / Choc / Topping) and
manual insert may only be filled with materials for the
use intended.
Health hazard.
When handling special cleaners for the milk foamer,
cleaning tablets, and the descaling solution, follow
the protective measures on the packaging. The special
cleaners for the milk foamer and cleaning tablets are
irritants. Only put in cleaning tablet or descaling solution
after the display message.
Irritation and scalding hazard.
Never reach under the spouts while cleaning / descaling.
Cleaning fluid / descaling solution runs out of the combi
spout when cleaning / descaling.
Slipping hazard
Fluids can be discharged from the coffee machine if
used improperly or if errors occur. These fluids can cause
a slipping hazard.
64
Caution.
Bruising or crushing
hazard.
Risk of injury.
Caution.
Health hazard.
Only use as intended.
Caution.
Health hazard.
Follow the instructions of the
label on the cleaning agents.
Caution.
Health hazard.
Irritation and scalding hazard
in the dispensing area.
Caution.
Slipping hazard if fluids
are discharged
Slipping hazard.
User Manual WMF 1200 S
Safety
10.2 Hazards to the coffee machine
Please observe the following instructions
so as to prevent problems with and damage
to the coffee machine:
• For drinking water with carbonate
hardness in excess of 5 °dKH,
a WMF water filter must be fitted;
otherwise, the coffee machine can be
damaged due to build-up of scale.
• For insurance reasons always ensure
that, at the end of operation, the mains
tap for the water supply is turned off
and the mains switch is switched off or
the mains plug is unplugged.
• We recommend damage prevention
measures such as:
- installation of a suitable water
monitor in the mains water supply
- installation of smoke alarms
• After shut off for several days we
recommend running the cleaning
program at least twice before reusing
the machine.
w Cleaning instructions
10.3 Intended use
The WMF 1200 S is designed to dispense
coffee beverages, milk beverages and/or
powdered beverages (Choc and Topping)
in various variations into cups or pots.
In addition, the device can generate
steam for heating milk and dispensing
hot water. This device is also intended for
industrial and commercial use and for
use by professionals and trained users in
shops in the consumer goods industry and
agricultural holdings, or for the commercial
use by non-professionals. The device can
be used as a self-service device if it is
supervised by trained personnel.
User Manual WMF 1200 S
The use of the device is also subject to the
“General Terms and Conditions” of WMF AG
and this User Manual. Any other use or use
that goes beyond the aforementioned is
considered incorrect use. The manufacturer
shall not be liable for any damage resulting
from this.
Under no circumstances may the
WMF 1200 S be used to dispense and
heat liquids other than coffee, hot water
(beverages, cleaning) or milk (cooled,
pasteurised, homogenised, UHT).
65
Safety
10.4 Directives
The device fulfils the requirements of the
German Food and Feed Code (LFGB), the
Regulation on Commodities (BedGgstV),
the EU regulation No. 10/2011 as well as
the EU regulation No. 1935/2004 in the
currently valid editions.
When used properly, the device does
not present a health hazard or other
unreasonable hazard.
The materials and raw materials used fulfil
the requirements of the Regulation on
Commodities as well as the EC regulations
No. 10/2011.
The device fulfils the requirements of all
applicable regulations in the directives MD
(MR) 2006/42/EC (EG), Directive 2004/108/
EC (EMC), Directive 2011/65/EC (ROHS),
Directive 2002/96/EC (WEEE).
The declaration of conformity is included
with the device. The device bears the CE
mark.
66
Any modifications that are not approved by
WMF will cause this declaration to become
invalid.
Currently valid national rules apply in
countries outside of the European Union.
This device is subject to the directive on
waste electrical and electronic equipment
(WEEE / EU directive) and may not be
disposed of as domestic waste.
For disposal please contact the WMF Service.
Address
w p age 57
Requirements traceability pursuant
to EC regulation No. 1935/2004 and
Good Manufacturing Practice within
the meaning of EC regulation No.
2023/2006 are ensured and guaranteed.
User Manual WMF 1200 S
Safety
10.5 Duties of the owner / operator
The operator of such equipment
must ensure regular maintenance by
WMF Service technicians, their agents or
other authorised persons, and checking of
safety devices.
Access to the service area is permitted only
for persons with knowledge and practical
experience with the device, especially
regarding safety and hygiene.
The coffee machine must be set up by the
operator such that care and maintenance
can be performed without hindrance.
In office / floor supply or similar
self-service applications, only staff
instructed in operation of the coffee
machine should supervise the coffee
machine. Trained personnel should carry
out care procedures and be available for
questions regarding use.
The operator shall ensure that electrical
equipment and operating facilities are
in a fit state (e.g. to BGV A3) [German
Accident Prevention Association or
equivalent]. In order to ensure the
operating safety of your coffee machine,
it is essential to perform regular checks
of the safety valves and the pressure
containers, among other checks.
User Manual WMF 1200 S
These measures are conducted by
WMF Service or by WMF authorised service
personnel as part of the maintenance work.
Machine cleaning must be carried out
using only the WMF special cleaning agent
intended by WMF for the coffee machine
(tablets), and for the milk system (cleaning
liquid).
WMF special cleaning agent
w Accessories and spare parts
page 72
Machine may only be descaled using the
special WMF descaling agent.
WMF special descaling agent
w Accessories and spare parts
page 72
The manufacturer's specifications regarding
maintenance cycles and frequency of
Maintenance) must be
maintenance (w observed.
67
Safety | Warranty claims
10.6 Warranty claims
During the warranty period of 12 months from transfer of
risk, the purchaser has statutory warranty entitlements.
The vendor should always be afforded the opportunity to
rectify errors within an appropriate period.
Claims above and beyond the above, in particular damage
claims as a result of consequential damage, are excluded,
to the extent that this is legally permissible.
Material defects shall be reported to the vendor
immediately and in writing.
Warranty period 12 months
No warranty is provided:
• On any parts subject to natural wear and tear. This
includes seals, mixers, and brewing unit, among other
items.
• For malfunctions due to the effect of the weather,
scale build-up, chemical, physical, electrochemical or
electrical effects, unless attributable to a fault on the
part of WMF.
• If a water filter is not fitted even though the local water
supply requires use of a water filter and malfunctions
occur as a consequence.
• With respect to faults which occur as a result of
failure to follow handling instructions and regulations,
maintenance and care of the device (e.g. User Manual
and maintenance instructions).
• With respect to faults which occur as the result of
failure to use original WMF spare parts or incorrect
assembly by the purchaser or by third parties or by
faulty or negligent treatment.
• With respect to the consequences of improper
modifications undertaken without our consent or
by repair or reconditioning work on the part of the
purchaser or by third parties.
• With respect to faults caused by inappropriate or
improper use.
68
Follow the manual.
The customer is advised in the
order confirmation whether or not
use of a water filter is required.
Maintenance
w p age 56
User Manual WMF 1200 S
User Manual WMF 1200 S
Using standard cleaning
Continue with steps
3–6, standard
Turn the adapter in
the socket by ⅛turn,
clockwise, until it stops
5 Plug&Clean
Place a collection
container with approx.
2 litres capacity under
the combi spout
Touch
Rinsing starts.
5 Standard
The display shows the
individual steps that must
be completed.
6 Standard
cancel: C
Remove the adapter
from the Plug&Clean
socket after rinsing
in progress
Plug&Clean
start: P
in socket?
insert tablet
Add a cleaning tablet
and close the cover
into manual insert
7
6 Plug&Clean
After the rinse, some
hot water remains in the
milk hose.
Hold the open end of the
milk hose over the drip
tray so that the remaining
rinse water can run out.
Observe the Safety chapter.
Caution.
Hot liquids in the
dispensing area.
P&C adapter locked
The milk system is rinsed
using hot water.
Hot water is drained
through the combi spout.
Continue with Step 7
in progress
milk system rinsing
With Plug&Clean
Continue with steps
3–6, Plug&Clean
cancel: C
Touch
Machine cleaning starts.
If choc beverages have
been dispensed, the
machine cleaning starts
with mixer rinsing.
start: P
8
Open left machine
door
3 Plug&Clean
Confirm with
OK: P
once per day
at least
cancel: C
33 2603 0010 1.0 01.2013
Duration approx.
7 minutes.
A minute countdown timer
shows the time remaining
in the cleaning cycle.
time remain: 7 min
cleaning in progress
9
Insert the milk hose
with the Plug&Clean
adapter into the
Plug&Clean socket
4 Plug&Clean
Prepare 0.3 l of clear,
cold drinking water for
the water rinsing
start: P
in water
cancel: C
Confirm with
that
the drip tray and the
grounds container has
been emptied
OK: P
in cleaning solution
browse: -/+
switching off
empty grounds cont.
4 Standard
milk hose
3 Standard
Soak combi spout
2
empty drip tray
1
Access the displayed
program by pressing
OK: P
Touch
until the desired program is displayed
Access the displayed program by pressing
browse: -/+
select clean.program
Access a care program without a message having appeared on the display.
Touch
Call up the care programs
cleaning
Machine cleaning
Cleaning programs
Care pad
your selection pls
08:15
09.01.2013
For all automatic cleaning programs, the combi spout, the milk nozzle, and the milk hose
must be installed.
Follow the overview of the cleaning interval schedule in the Care chapter in the
User Manual.
Prior to the first cleaning, read the User Manual, Care chapter.
Please refer to the User Manual.
Cleaning instructions WMF 1200 S
2
1
browse: -/+
Plug&Clean
cancel: C
2
After 5 hours, rinse all combi
spout and milk hose parts
C
Caution.
Carefully disconnect
the milk hose.
A
3
09.01.2013
If a mixer is fitted:
Rinse mixer hose very
thoroughly
Reassemble combi spout
Replace combi spout
Insert milk hose
If a mixer is fitted:
Insert mixer hose
4
Turn the adapter in
the socket by ⅛turn,
clockwise, until it stops
4
The milk system is rinsed
using hot water.
Hot water is drained
through the combi spout.
in progress
milk system rinsing
Caution.
Hot liquids in the
dispensing area.
cancel: C
Remove the adapter
from the Plug&Clean
socket after rinsing
in progress
Plug&Clean
start: P
in socket?
P&C adapter locked
5
After the rinse, some
hot water remains in the
milk hose.
Hold the open end of the
milk hose over the drip
tray so that the remaining
rinse water can run out.
Observe the Safety chapter.
Immerse the length of the
remaining milk hose in the
cleaning solution
This procedure prevents air
bubbles from remaining in the
milk hose.
Place all parts of combi spout
in the cleaning solution
(3 parts)
All parts must be completely
immersed in the cleaning
solution.
Foamer cleaning:
for intermediate milk system cleaning, see “Milk system cleaning”.
Manual combi spout cleaning without Plug&Clean:
perform at least once per day.
Manual combi spout cleaning with Plug&Clean:
perform at least once per week.
After Plug&Clean cleaning:
the cleaned milk hose can be stored with the adapter in the closed
cooler.
Instructions
Dismantle combi spout
Immerse one end of the milk
hose in the cleaning solution
B
Prior to cleaning switch off using the ON/OFF button. Disconnect mains plug.
After the mixer is rinsed,
the “Ready to operate”
display appears.
08:15
your selection pls
3
Insert the milk hose
with the Plug&Clean
adapter into the
Plug&Clean socket
3
Place a collection
container with approx.
2 litres capacity under
the combi spout
Touch
Rinsing starts.
Pull forward the lever behind
the combi spout
Remove combi spout
Remove milk hose from milk
container and release from
combi spout
If a mixer is fitted:
Release the mixer hose
ZUser Manual
Mix 5 ml of WMF Special
cleaner with 0.5 l of lukewarm
water
Manual combi spout cleaning at least 1 x daily
Touch
Mixer rinsing starts.
start: P
mixer rinsing
browse: -/+
Access the displayed
program by pressing
OK: P
1
Open left machine
door
2
mixer rinsing
Mixer rinsing
Access the displayed
program by pressing
OK: P
cancel: C
Prepare 0.3 l of clear,
cold drinking water for
the water rinsing
Milk system cleaning Plug&Clean
The display shows the
individual steps that must
be completed.
Access the displayed
program by pressing
start: P
in water
milk hose
browse: -/+
1
OK: P
milk system rinsing
Milk system rinsing
Overview of additional instructions
Overview of additional instructions
69
Technical data
Technical data
Technical data for coffee machine
Nominal power rating *
2.0–2.4 kW
Recommended daily capacity
espresso, café crème
up to 80 cups per day
Overall hot water output
approx. 16 liters per hour
Coffee bean hopper
approx. 500 g per load
Choc hopper / Topping hopper
approx. 500 g
Mains power connection *
1,N,PE 50/60 Hz 220–240 V
Illumination
LED class 1
External dimensions
Width 324 mm
Height incl. bean hopper 682 mm
Depth 554 mm
Weight empty
approx. 33–38 kg (depending on the model)
Continuous sound pressure level (Lpa) **
< 70 dB(A)
We reserve the right to make technical modifications.
* For special models see model label, values given above are for the basic model.
** A-evaluated sound pressure level Lpa (slow) and Lpa (impulses) at operating personnel workplace is under 70 dB(A)
in any working mode.
Conditions for usage and installation
Necessary on-site preparatory work for electricity, water and drainage connections at the
customer‘s premises are to be arranged by the machine owner / operator. The work must
be carried out by authorised installation technicians in compliance with general, countryspecific and local regulations. The WMF service engineers may only connect the coffee
machine to existing prepared connection points. WMF Service is neither authorised
nor responsible for carrying out any on-site installation work prior to connection. The
potential equalization terminal is installed by WMF Service if needed.
70
User Manual WMF 1200 S
Technical data
Mains voltage tolerance
range
Water supply
(Constant water supply
optional)
Water quality
Water drain tube
Ambient temperature
Maximum humidity
Degree of protection
Installation surface
Installation clearances
Installation dimensions
of the water filter
230 V +6 % and–10 %,
Mains voltage interruption < 50 ms: no interruption of function
3/8 inch hose connector with mains tap, and filter with 0.2 to 0.25 mm
mesh size, on site.
Min. 0.2 MPa flow pressure at 2 litres / minute, max. 0.6 MPa.
Water temperature maximum 35 °C.
The set of hoses provided with the new coffee machine and/or the new
water filter must be used. Do not use old hoses.
For drinking water with carbonate hardness above 5 °dKH, a WMF water
filter should be fitted upstream.
Tube a minimum of DN 19, minimum downward slope of 2 cm/m
+5 °C to max. +35 °C (empty the water system in case of frost).
80 % relative humidity without condensation.
Do not use device outdoors.
IP X0
The device must be placed on a level, flat, and sturdy surface.
The device is not intended to be located on a surface that is sprayed or
cleaned with a water hose, steam jets, steam cleaner, or similar devices.
For operating, service and safety reasons the machine should be installed
with a clearance of not less than 50 mm at the back and sides from
the building or non-WMF components. A minimum working space of
800 mm in front of the coffee machine is recommended. A clear height
of 1,100 mm from the top of the supporting surface should be ensured.
The height of the installation surface above the floor is at least 850 mm.
If the coffee machine connections are to be run downwards through the
counter, please make space for the lines, which can reduce the usable
space below the machine.
See the User Manual for the water filter.
These specifications for the electrical connection and the standards quoted apply for connecting
the coffee machine in EU countries. It may be necessary to also observe additional country-specific
regulations. Outside the EU countries, acceptance of the standards quoted is to be checked by the legal
entity or natural person who wishes to use the coffee machine.
The local power supply must be constructed according to IEC 364 (DIN VDE 0100). To improve safety, the device should
be fitted with an FI 30 mA earth leakage current circuit breaker complying with EN 61008. (Type B residual current
circuit breakers provide reliable tripping even if the fault current is smooth. This ensures a high level of safety.) Near
the device or about 30 cm below the counter top there should be a shockproof socket as a single-phase connection
installed locally on the rear or side wall of the counter substructure or a country-specific single-phase socket. If
the mains cable for this device is damaged then it must be replaced by our service personnel or a similarly qualified
person, in order to prevent hazards. The mains cable must not come into contact with hot surfaces. The mains switch
and plug top are part of the on-site installation. The coffee machine may not be fitted with a fixed permanent mains
connection if installed on a transporting trolley (a mobile station).
In order to avoid possible faults from arising on our shielded data lines due to potential equalisation currents
between the devices, an additional potential equalisation unit should be planned for devices connected to the
vending system. (See EN 60309)
User Manual WMF 1200 S
71
Number
Unit
Designation
72
Pcs
Pcs
Pcs
Pcs
1
1
1
1
Pcs
1
33 2318 0000
Mixer bowl
Meter
1,5
Pcs
Pcs
Pcs
1
Pcs
Pcs
Pcs
Sheet
1
1
1
1
Product hopper
Pcs
Pcs
1
2
Pcs
Pcs
1
1
Complete bean hopper
1
Labels for product hopper
Product hopper lid
Topping product hopper
33 2315 3000
33 2268 9000
33 2824 8000
33 2823 5000
33 2291 1000
O-ring container
Choc product hopper
00 0047 3105
33 2292 7000
33 2265 5000
33 2253 1000
33 2603 0010
Screw, access guard
Hand guard
Slide lock
Bean hopper
Set of documents:
• 1200 S User Manual
• 1200 S cleaning instructions (Standard / Easy Milk)
• Carbonate hardness test (with instruction)
33 2323 1000
00 0048 0042
Drain tube
Multitool
33 2165 8000
Connecting tube for constant water supply
Angle for drain tube
Documentation / instructions
1
Accessories / tools
Pcs
Pcs
1
1
33 2292 1000
33 2292 6000
00 0048 0064
33 9516 9000
33 2317 8000
33 7007 1714
33 9510 6100
00 0048 4948
33 2867 5200
Order No.
Mixer hose spring
Mixer hose
Milk nozzle for warm milk (white)
Milk nozzle for warm milk (green)
Milk nozzle for cold milk (light blue)
Milk nozzle for cold milk (orange)
Milk hose
Milk foamer
Constant water supply, drainage
Pcs
1
Meter
Meter
0,25
Pcs
1
0,7
Combi spout, complete, with Choc / Topping
4
1 and 4
4
4
1
1
1
1
1
1
1
Installation instructions
Installation instructions
Installation instructions
7
7
7
7
7
7
7
7
7
Position number
all
all
Topping
Choc
all
all
all
all
all
all
all
with drainage
with drainage
Constant water supply
Mixer bowl
Choc / Topping
Choc / Topping
Fresh milk
Fresh milk
Fresh milk
Fresh milk
Fresh milk
all
Model
Accessories and spare parts
Accessories and spare parts
User Manual WMF 1200 S
Number
Unit
Designation
Pcs
Pcs
User Manual WMF 1200 S
Drip grid
Drip tray
Brewing unit
Coffee grounds container
Pcs
Pcs
1
1
Pcs
1
Angle
33 7006 2608
Water tank sieve
Pack
1
33 2332 2000
Water tank cartridge (VE 4 pcs)
1
Pcs
Customer Check-up Kit 15.000
Bottle
Pack
Pack
Bottle
Pcs
Pcs
Tube
1
1
1
2
1
1
1
WMF Molykote “gasket grease”
Cleaning brush
Pipe cleaner
Liquid descaling agent (0.75 l)
Special cleaning tablets (100 pieces)
Special cleaning tablets for the WMF milk system
WMF Special cleaner for milk foamer
Order numbers for the WMF care program
33 2179 9000
33 1521 9000
33 0350 0000
33 7006 2869
33 2332 4000
33 2622 0000
33 0683 6000
33 2878 3000
33 2432 4000
Bestmax V water filter (complete kit)
Replaceable cartridge for Bestmax water filter
Customer Check-up Kit 15.000
Pcs
Pcs
1
1
03 9333 0001
33 2534 2000
33 2533 4000
00 0047 2055
00 0047 3414
00 0047 2257
33 2107 1100
33 2600 3000
33 2254 9100
33 2823 6199
33 2880 5000
Order No.
Water tank lid
Water tank
Hex nut
Flathead screw M6X16
Toothed wheel
Scale filter / water filter
Pcs
Pcs
1
1
Water tank
Pcs
Pcs
1
1
Potential equalization terminal
Pcs
Pcs
1
1
Drip tray / drip grid
1
Brewing unit
1
Coffee grounds container
17
17
17
10
10
15
9
Position number
all
all
all
all
all
all
Fresh milk
all
Water tank
Constant water supply
Constant water supply
Water tank
Water tank
Water tank
all
all
all
all
Model
Accessories and spare parts
73
Index
Index
A
Accessories and spare parts 72
Additional instructions 2, 69
Automatic switch on time 33
B
Basic settings 32
Bean hopper 7, 21, 48
Bean hopper cleaning 48
Beverage button 18
Beverage buttons 7
Beverage dispensing 9, 18
Brewing pressure 31
Brewing temperature 35
Brewing unit 7, 47
Brewing unit cleaning 47
C
Capacity 9
Carbonate hardness 9
Care 42
Change recipes 27
Check grinding degree 30
Choc 9
Choc hopper 7, 70
Cleaning intervals 42
Cleaning intervals overview 42
Cleaning program 44
Cleaning schedule 54
Clean the brewing unit 47
Clearance height 20
Coffee bean hopper 70
Coffee grounds 22
Coffee machine maintenance 56
Coffee strength 28
Combi spout 7, 20
Combi spout cleaning 44, 45
Conditions for usage and installation 70
Connect the Easy Milk 13
Connect up the milk 13
Continuous sound pressure level 70
Cool milk 13, 55
Cover 7
C pad 7
Cup&Cool 13
Cup size 26
Cup volume 26
D
Daily cleaning 44
Date 15, 32, 36
Date / time 36
Delete counters 39
Descaling 50, 51, 53
Descaling coffee machine with constant water supply 51
Dispensing hot water 7, 20
74
Dispensing test 26, 27
Dosing auger 50
Drip grid 7
Drip tray 7, 23
Drip tray, cover and front panel 45
Duties of the owner / operator 67
E
ECO-mode 34
Electrical connection 71
Error 58
Error list 59
Error message 59
External dimensions 70
F
Factory settings 37
Fill the bean hopper 14
Filter change 50
Foamer cleaning 44
Foamer rinsing 44
G
Glossary 9
Grounds container 7, 22
Grounds container cleaning 45
Grounds disposal through the counter 22
H
HACCP cleaning schedule 54
Hazards to the coffee machine 65
Hazards to the operator 63
Height adjustment of the combi spout 20
Hot water button 7, 20
Hot water output 70
I
Illumination 70
Instructions 58
Intermediate cleaning 45
Introduction 6
K
Keep counter settings 39
L
Labelling of beverage buttons 41
Label template 41
Language 32
Level indicator 23
M
Mains power connection 70
Mains tap 9
Maintenance 56
User Manual WMF 1200 S
Index
Malfunctions 59, 61
Manual insert 7, 21
Mechanical settings 41
Menu pad 7
Messages 58
Messages and instructions 58
Messages for operation 58
Milk cooler adapter 13
Milk foamer 20
Milk foam volume 28
Milk nozzle 13
Milk system 9
Milk system cleaning 44
Milk volume 29
Mixer cleaning 46
Mixer rinsing 45
Mixer system 9
N
Nominal power rating 70
No warranty is provided 68
O
Operating messages 58
Operation 18
Original WMF spare parts 68
O-rings 9
Other settings 41
P
Parts of the coffee machine 6
PIN protection 38
Plug&Clean 44, 45
Plug&Clean cleaning 45
Potential equalization terminal 70
Pre-infusion 9
Preinfusion 29
Preparation 52
Pressing 9
Product hopper 21
Product hopper cleaning 49
R
S
Safety 63
Safety devices 63
Sanitize milk system 54
Self-service 9
Sequence of milk and coffee dispensing 29
Set grinding degree 30, 41
Settings (basic settings) 15
Start-up complete 17
Start-up program 15
Switch off 23
Switch off time 32
Switch on 18
Switch on the coffee machine 15, 18
Switch on time 32
T
Tablet insert 7, 21
Technical data 70
Test new settings 26
Time 15, 32, 35
Topping 9
Topping hopper 7
Touch-screen display 7
U
Use additional types of coffee 21
User Manual Signs and Symbols 8
User Manual Symbols 8
W
Warm rinsing 14
Warranty claims 68
Water filter 68
Water hardness 36
Water tank 7
Water tank cleaning 46
Water volume 28
Weekly cleaning 46
Weight empty 70
Without water drain 23
WMF Service 57
Work on site 70
Read counters 39
Ready to operate 18
Recommendation for Choc and Topping 55
Recommended daily capacity 70
Regular cleaning 47
Rinsing 9, 52, 53
User Manual WMF 1200 S
75
Your nearest WMF Service:
© 2012–2013 WMF AG
All rights reserved, in particular duplication, distribution and translation rights.
No part of this manual may be reproduced in any form or processed, duplicated or
distributed using electronic systems without written consent.
Design and production / typesetting and print presentation:
TecDoc GmbH; Geislingen, info@tecdocgmbh.de
Original User Manual. Printed in Germany.
We reserve the right to make technical modifications.
31.01.2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising