Parts Breakdown

Parts Breakdown
Classic Washfountain
Parts & Service Guide
215-1370 Rev. N; ECN 12-00-014
© 2012 Bradley
Page 1 of 67 9/5/2012
P.O. Box 309, Menomonee Falls, WI 53052-0309
TEL. 1-800-Bradley FAX 262-251-5817
http://www.bradleycorp.com
Bradley Washfountains
Parts and Service Guide
Table of Contents
Washfountain Identification
Page #
Identification Charts and Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
How to Determine Drain Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Classic Washfountains
Washfountain Fittings — Type A Drain - Foot Control (Semi-Circular shown) . . . . . . . . . . . . . . . .7-8
Washfountain Fittings — Type H Drain - Foot Control (Semi-Circular shown) . . . . . . . . . . . . . .9-10
Washfountain Fittings — Type O Drain - Foot Control (Semi-Circular shown) . . . . . . . . . . . . .11-12
Washfountain Fittings — Type B Drain - Foot Control (Semi-Circular shown) . . . . . . . . . . . . .13-14
Bowls — Replacement Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Pedestals — Circular Washfountains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Pedestals — Semi-Circular Washfountains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-18
Pedestals — Corner Washfountains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Panels — Circular Pedestal Panels for Stainless Steel, Terrazzo, and Terreon® Bowls . . . . . . . . . . .20
Panels — Semi-Circular Pedestal Panels for Terrazzo and Terreon Bowls . . . . . . . . . . . . . . . . . . . .21
Panels — Semi-Circular Pedestal Panels for Stainless Steel Bowls . . . . . . . . . . . . . . . . . . . . . . . . . .22
Panels — Pedestal Panels for Bradstone Bowls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Panels — Corner Washfountain Stainless Steel Pedestal Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Linkage — Circular Washfountain Foot Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Linkage — Semi-Circular Washfountain Foot Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Linkage — Corner Washfountain Foot Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Paper Towel Dispensers — Circular Washfountains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Paper Towel Dispensers — Circular Washfountains with Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Paper Towel Dispensers — Semi-Circular Washfountains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Paper Towel Dispensers — Semi-Circular Washfountains with Shroud . . . . . . . . . . . . . . . . . . . . . .31
Restraining Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Foot Valve and Linkage (January 2003 to present) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Foot Valve and Linkage (November 1973 to January 2003) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Foot Valve Adjustment (November 1973 to January 2003) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Stop, Strainer, and Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Adjusting the Vernatherm™ Mixing Valve (August, 2004 to Present) . . . . . . . . . . . . . . . . . . . . .37-39
Mixing Valve — Vernatherm™ — Thermostatic (Prior to Aug, 2004) . . . . . . . . . . . . . . . . . . . . . . .40
Mixing Valve — Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Volume Control Valve Repair Parts — S02-0245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Sprayheads — Standard w/Neoprene Spray Ring Grommet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Sprayhead Service Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Sprayhead Tubing Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Soap Valve — Liquid — S09-007S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Soap Valve — Lotion — S09-057S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Soap Valve — Powdered — S09-010A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Soap Maintenance Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Continued on Page 3
2
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Parts and Service Guide
Bradley Washfountains
Table of Contents ....Continued
Electronic Activation
®
Infrared Module — AccuZone Circular & Semi (Terrazzo and Stainless Steel Bowls,
Bradstone Bowls Prior to September 2003) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Infrared AccuZone Valve Assembly — Circular & Semi
(Terrazzo and Stainless Steel Bowls, Bradstone Bowls Prior to September 2003) . . . . . . . . . . . . . . . . .49
Infrared AccuZone Wiring — Circular & Semi (Terrazzo and Stainless Steel Bowls,
Bradstone Bowls Prior to September 2003) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Troubleshooting AccuZone Infrared . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Infrared Module — Adaptive — Circular & Semi
(Terreon, Bradstone Bowls from September 2003 to Present) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Infrared Adaptive Valve Assembly — Circular
(Terreon, Bradstone Bowls from September 2003 to Present) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Infrared Adaptive Valve Assembly — Semi-Circular
Infrared ®Adaptive Wiring — Circular (Terreon, Bradstone Bowls from September 2003 to Present) . .52
(Terreon , Bradstone Bowls from September 2003 to Present) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Infrared ®Adaptive Wiring — Semi-Circular
(Terreon , Bradstone Bowls from September 2003 to Present) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Toubleshooting Adaptive Infrared . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Touch Time ™ Module — Circular & Semi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Touch Time ™ Valve Assembly — Circular & Semi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Touch Time ™ Wiring — Circular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Touch Time ™ Wiring — Semi-Circular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Troubleshooting Touch Time ™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Elctrical Activation — Common Parts List
Solenoid Parts Breakdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Solenoid Parts Breakdown (Prior to March 20, 2002) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Solenoid Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Mechanical Activation
Air Valve Module — Circular & Semi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Air Valve Valve Assembly — Circular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Air Valve Valve Assembly — Semi-Circular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Air Valve Tubing Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Air Valve, Adjusting the Metering Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Air Valve Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Conversion Kits (Non Sectional)
S50-311 Converts Circular Foot Control to AccuZone Infrared . . . . . . (See Instruction Sheet 215-840)
S50-310 Converts Semi-Circular Foot Control to AccuZone Infrared . . .(See Instruction Sheet 215-840)
Conversion Kits Sectional)
S50-322 Converts 36" Semi-Circular Foot Control to AccuZone Infrared . . . . (See Instruction Sheet 215-889)
S50-321 Converts 54" Semi-Circular Foot Control to AccuZone Infrared . . . . (See Instruction Sheet 215-889)
S50-320 Converts 36" Circular Foot Control to AccuZone Infrared . . . . . . . . . (See Instruction Sheet 215-889)
S50-319 Converts 54" Circular Foot Control to AccuZone Infrared . . . . . . . . . (See Instruction Sheet 215-889)
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
3
Bradley Washfountains
Parts and Service Guide
Classic Washfountain Products
Terrazzo
– Infrared, Touch Time,
Air Valve or Foot Operated
•
•
•
WF2603
WF2604
9" deep bowl (cement with limstone chips)
Available in Granito, White Marmorite,
Dusty Rose, and Whisper Gray
Stainless pedestal panels
Models Available:
WF2603
WF2604
WF2605
WF2608
WF2613
36"
54"
36"
54"
54"
semi-circular
semi-circular
circular
circular
corner (Not shown)
Stainless Steel
– Infrared, Touch Time,
Air Valve or Foot Operated
•
•
WF2605
WF2703
WF2608
WF2704
9" deep bowl
Stainless steel bowl and pedestal panels
Models Available:
WF2703
WF2704
WF2705
WF2708
36"
54"
36"
54"
semi-circular
semi-circular
circular
circular
Bradstone
– Infrared, Touch Time,
Air Valve or Foot Operated
•
•
•
WF2705
WF2803
WF2708
WF2804
9" deep bowl (reinforced polyester resin)
Available in Driftwood Beige
and White Marble
ABS tapered pedestal panels
Models Available:
WF2803
WF2804
WF2805
WF2808
4
36"
54"
36"
54"
semi-circular
semi-circular
circular
circular
WF2805
WF2808
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Parts and Service Guide
Bradley Washfountains
Terreon® Washfountain Products
Terreon® Classic
•
•
•
•
•
9" deep bowl (Solid Surface)
Shares pedestal and most components
with Classic Terrazzo
Available in soapstone gray and
canyon tan colors
Stainless pedestal panels
Standard Rim Height 29-1/2"
Models Available:
WF2503
WF2504
WF2505
WF2508
36"
54"
36"
54"
semi-circular
semi-circular
circular
circular
Extra-Height Terreon® Classic
(Parts not shown in this book)
• 9" deep bowl (same as Terreon® Classic), 34" rim
•
•
•
height (36" semi-circular model has 35" rim height)
Shares all components except the bowl with the
Terreon® Deep Bowl
Available in soapstone gray and canyon tan colors
Gel-coated fiber-glass pedestal
Models Available:
WF3203
WF3204
WF3208
36" semi-circular
54" semi-circular
54" circular
Terreon® Deep Bowl
(Parts not shown in this book)
• ADA compliant models available
• Shares all components except the bowl with the
•
•
Terreon® Extra Height Classic Series
Available in all colors except soapstone gray and
canyon tan
Standard Rim Height 34"
Models Available:
TDB3103 36" semi-circular
TDB3104 54" semi-circular
TDB3108 54" circular
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
5
Bradley Washfountains
Parts and Service Guide
How to Determine Drain Type
(Parts may vary depending upon drain type.
Identify your drain type before continuing.)
TRAP FOR WALL OUTLET ONLY
DRAIN THROUGH WALL
TRAP FOR WALL OUTLET ONLY
DRAIN
THROUGH WALL
CLEARANCE HOLE
WALL
CLEARANCE HOLE
Type O
Off-line vent with supplies from above.
WALL
Type A
Off-line vent with supplies from below.
SIDE VIEW
SIDE VIEW
FLOOR
FLOOR
SUPPLIES
THROUGH WALL
DRAIN & SUPPLIES
THROUGH FLOOR TRAP
LOCATED BELOW FLOOR
(OPTIONAL)
DRAIN & SUPPLIES THROUGH
LOCATED BELOW FLOOR
(OPTIONAL)
Type B
Centrally rising vent with supplies from above.
Type H
Centrally rising vent with supplies from below.
VENT
SIDE VIEW
WALL
VENT
SIDE VIEW
FLOOR
DRAIN THROUGH FLOOR
DRAIN THROUGH FLOOR
SUPPLIES THROUGH FLOOR (OPTIONAL)
6
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Washfountain Fittings
Type A Drain – Foot Control – (Semi-Circular shown)
Complete Soap Assemblies
Items 2 through 10 comprise a complete soap dispenser
assembly. For a complete assembly, order as follows:
S11-144 Nylon LSD
—
Semi-circular
S11-153 Nylon PSD
—
Semi-circular
S11-180 Metal LSD
—
Semi-circular
S11-189 Metal PSD
—
Semi-circular
S11-126 Nylon LSD
—
Circular
S11-135 Nylon PSD
—
Circular
S11-162 Metal LSD
—
Circular
S11-171 Metal PSD
—
TYPE "A" DRAIN
2
Circular
For washfountains without soap dispensers,
delete items 4 through 10.
4
PARTS SHOWN IN
BOX ARE FOR
UNITS WITH SOAP
DISPENSER.
7
5
8
10
9
26
21
1
3
12
28
20
24
11
15
26
13
22
25
17
16
21
18
14
23
19
26
27
25
24
Optional Vernatherm
Thermostatic Mixing Valve
See Pages 24-26
Parts List on next page
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
7
Bradley Washfountains
Parts and Service Guide
Washfountain Fittings ....Continued
Type A Drain – Foot Control
Parts List
•
**
8
See previous page for panel item listing
Semi &
Corner
54"
36"
Qty
Qty
Item
Part No.
Description
1
2
3
4
5
7
**
8
9
10
11
11
11
12
12
13
13
14
14
14
14
14
15
**
**
**
**
**
16
16
17
18
19
19
20
•21
**
22
•23
24
25
26
•27
28
See Page 32
S66-002
107-099
S10-004
176-010
S09-010A
S09-007S
113-155A
S66-001
159-009A
S05-054B
S05-054C
S05-054
S57-005
S57-006
176-008A
176-008
113-125A
113-124A
113-123A
113-122A
113-245
173-002
160-044
112-015
112-016
142-068
161-021
125-008
125-011
159-009
S66-003
S14-007
S14-007A
S07-066
S60-003
159-019
S02-045
S01-038
110-005
129-007
124-001AF
S01-525
129-009
Restraining Bracket
Locking Cap Nut
Dispenser Cover – Type A
Nylon Filler Cap
Upper Tie Rod
Powdered Soap Valve
Liquid Soap Valve – Brass
Nylon Support Tube Spacer
Locking Coupling Nut
Upper Tie Bar
Sprayhead, Semi-Circle Units
Sprayhead, Corner Units
Sprayhead, Circular Units
Sprayhead Support Tube
Sprayhead Support Tube
Lower Tie Rod
Lower Tie Rod
Supply Pipe, Terrazzo or Terreon® Bowl
Supply Pipe, Terrazzo or Terreon® Bowl
Supply Pipe, Stainless Steel Bowl
Supply Pipe, Stainless Steel or Bradstone Bowl
Supply Pipe, Bradstone Bowl
Strainer
Strainer Screw
Drain Spud, Terrazzo, Terreon® or Bradstone Bowl
Drain Spud, Stainless Steel Bowl
Washer
Drain Spud Lock Nut
Support Tube Gasket, Stainless Steel Bowl
Support Tube Gasket, All Other Bowls
Lower Tie Bar
Locking Hex Nut
Operating Rod Assy., Std. Ht.
Operating Rod Assy., Juv. Ht.
Foot Valve
Combination, Stop, Strainer, and Check Valve
Operating Cross
Volume Control Valve
Manual Mixing Valve
Tail Piece Nut
Tail Piece – Unplated
Tail Piece Washer – Fiber
Vernatherm Assy. — Thermostatic Mixing Valve
Foot Valve Tail Piece
1
1
1
2
1
2
2
1
1
1
1
1
—
1
—
1
—
1
—
1
—
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
—
1
1
3
2
3
1
1
1
1
1
2
1
2
2
1
1
1
1
—
—
—
1
—
1
—
1
—
1
—
1
2
1
1
1
1
1
1
1
1
1
1
1
2
—
1
1
3
2
3
1
1
Circle
54"
Qty
—
1
1
2
1
4
4
1
1
1
—
—
1
1
—
1
—
1
—
1
—
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
2
3
1
1
36"
Qty
—
1
1
2
1
4
4
1
1
1
—
—
1
—
1
—
1
1
—
1
—
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
2
3
1
1
If any of these valves are desired complete with t ail pieces, tail piece nuts and washers, order as follows:
S60-003S, S01-038S, S01-522S
Not Illustrated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Washfountain Fittings
Type H Drain – Foot Control – (Semi-Circular shown)
Complete Soap Assemblies
Items 1 through 8 comprise a complete soap dispenser
assembly. For a complete assembly, order as follows:
S11-152 Nylon LSD
—
Semi-circular
S11-161 Nylon PSD
—
Semi-circular
S11-188 Metal LSD
—
Semi-circular
S11-197 Metal PSD
—
Semi-circular
S11-134 Nylon LSD
—
Circular
S11-143 Nylon PSD
—
Circular
S11-170 Metal LSD
—
Circular
S11-179 Metal PSD
—
Circular
TYPE "H" DRAIN
1
2
3
For washfountains without soap dispensers,
delete items 4 through 8.
PARTS SHOWN IN
BOX ARE FOR
UNITS WITH SOAP
DISPENSER.
4
7
8
10
25
24
9
26
22
17
12
20
16
20
22
14
13
18
17
21
11
15
19
22
23
21
20
Optional Vernatherm
Thermostatic Mixing Valve
See Pages 24-26
Parts List on next page
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
9
Bradley Washfountains
Parts and Service Guide
Washfountain Fittings ....Continued
Type H Drain – Foot Control
Parts List
•
**
10
See previous page for panel item listing
Semi &
Corner
54"
36"
Qty
Qty
Item
Part No.
Description
1
2
3
4
7
**
8
9
9
9
10
10
11
11
11
11
11
12
**
**
**
**
**
13
13
14
15
15
16
•17
**
18
•19
20
21
22
•23
24
25
26
26
160-108
107-048
159-020
S10-004
S09-010A
S09-007S
113-155A
S05-054B
S05-054C
S05-054
S57-005
S57-006
113-125A
113-124A
113-123A
113-122A
113-245
173-002
160-044
112-015
112-016
142-068
161-021
125-008
125-011
111-024
S14-007
S14-007A
S07-066
S60-003
159-019
S02-045
S01-038
110-005
129-007
124-001AF
S01-525
129-009
169-174
113-852
113-006AL
Cap Screw
Dispenser Cover – Type H
Tie Bar
Nylon Filler Hole Cap
Powdered Soap Valve
Liquid Soap Valve – Brass
Nylon Support Tube Spacer
Sprayhead, Semi-Circle Units
Sprayhead, Corner Units
Sprayhead, Circular Units
Sprayhead Support Tube
Sprayhead Support Tube
Supply Pipe, Terrazzo or Terreon® Bowl
Supply Pipe, Terrazzo or Terreon® Bowl
Supply Pipe, Stainless Steel Bowl
Supply Pipe, Stainless Steel or Bradstone Bowl
Supply Pipe, Bradstone Bowl
Strainer
Strainer Screw
Drain Spud, Terrazzo, Terreon® or Bradstone Bowl
Drain Spud, Stainless Steel Bowl
Washer
Drain Spud Lock Nut
Support Tube Gasket, Stainless Steel Bowl
Support Tube Gasket, All Other Bowls
Vented Trap
Operating Rod Assy., Std. Ht.
Operating Rod Assy., Juv. Ht.
Foot Valve
Combination, Stop, Strainer, and Check Valve
Operating Cross
Volume Control Valve
Manual Mixing Valve
Tail Piece Nut
Tail Piece
Tail Piece Washer – Fiber
Vernatherm Assy. — Thermostatic Mixing Valve
Foot Valve Tail Piece
3/8" Coupling
Nipple 2" Long, Std Height
Close Nipple, Juv Height
2
1
1
2
2
2
1
1
1
—
1
—
1
—
1
—
1
1
2
1
1
1
1
1
1
1
1
1
1
2
—
1
1
3
2
3
1
1
1
1
1
2
1
1
2
2
2
1
1
—
—
—
1
—
1
—
1
—
1
2
1
1
1
1
1
1
1
1
1
1
2
—
1
1
3
2
3
1
1
1
1
1
Circle
54"
Qty
36"
Qty
2
1
1
2
4
4
1
—
—
1
1
—
1
—
1
—
—
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
2
3
1
1
1
1
1
2
1
1
2
4
4
1
—
—
1
—
1
—
1
—
1
—
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
2
3
1
1
1
1
1
If any of these valves are desired complete with t ail pieces, tail piece nuts and washers, order as follows:
S60-003S, S01-038S, S01-522S
Not Illustrated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Washfountain Fittings
Type O Drain – Foot Control – (Semi-Circular shown)
Complete Soap Assemblies
Items 2 through 8 comprise a complete soap dispenser
assembly. For a complete assembly, order as follows:
S11-147 Nylon LSD
—
Semi-circular
S11-156 Nylon PSD
—
Semi-circular
S11-183 Metal LSD
—
Semi-circular
S11-192 Metal PSD
—
Semi-circular
S11-129 Nylon LSD
—
Circular
S11-138 Nylon PSD
—
Circular
S11-165 Metal LSD
—
Circular
S11-174 Metal PSD
—
Circular
TYPE "O" DRAIN
2
1
3
For washfountains without soap dispensers,
delete items 4 through 10.
4
PARTS SHOWN IN
BOX ARE FOR
UNITS WITH SOAP
DISPENSER.
7
5
8
10
9
12
25
20
28
11
27
19
23
25
13
21
16
15
20
24
17
14
22
25
26
24
23
18
See Pages 24-26
Optional Vernatherm
Thermostatic Mixing Valve
Parts List on next page
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
11
Bradley Washfountains
Parts and Service Guide
Washfountain Fittings ....Continued
Type O Drain – Foot Control
Parts List
•
**
12
See previous page for panel item listing
Semi &
Corner
54"
36"
Qty
Qty
Item
Part No.
Description
1
2
3
4
5
7
**
8
9
10
11
11
11
12
12
13
13
14
14
14
14
14
15
15
16
17
18
18
19
•20
**
21
•22
23
24
25
•26
27
**
**
**
**
**
28
See Page 32
S66-002
107-179
S10-004
176-010
S09-010A
S09-007S
113-155A
S66-001
159-009A
S05-054B
S05-054C
S05-054
S57-005
S57-006
176-008A
176-008
113-125A
113-124A
113-123A
113-122A
113-245
125-008
125-011
159-009
S66-003
S14-007
S14-007A
S07-066
S60-003
159-019
S02-045
S01-038
110-005
129-007
124-001AF
S01-525
173-002
160-044
112-015
112-016
142-068
161-021
129-009
Restraining Bracket
Locking Cap Nut
Dispenser Cover – Type O
Nylon Filler Cap
Upper Tie Rod
Powdered Soap Valve
Liquid Soap Valve – Brass
Nylon Support Tube Spacer
Locking Coupling Nut
Upper Tie Bar
Sprayhead, Semi-Circle Units
Sprayhead, Corner Units
Sprayhead, Circular Units
Sprayhead Support Tube
Sprayhead Support Tube
Lower Tie Rod
Lower Tie Rod
Supply Pipe, Terrazzo or Terreon® Bowl
Supply Pipe, Terrazzo or Terreon® Bowl
Supply Pipe, Stainless Steel Bowl
Supply Pipe, Stainless Steel, Terreon® or Bradstone Bowl
Supply Pipe, Bradstone Bowl
Support Tube Gasket, Stainless Steel Bowl
Support Tube Gasket, All Other Bowls
Lower Tie Bar
Locking Hex Nut
Operating Rod Assy., Std. Ht.
Operating Rod Assy., Juv. Ht.
Foot Valve
Combination, Stop, Strainer, and Check Valve
Operating Cross
Volume Valve
Manual Mixing Valve
Tail Piece Nut
Tail Piece
Tail Piece Washer – Fiber
Vernatherm Assy. — Thermostatic Mixing Valve
Strainer
Strainer Screw
Drain Spud, Terrazzo, Terreon® or Bradstone Bowl
Drain Spud, Stainless Steel Bowl
Washer
Drain Spud Lock Nut
Foot Valve Tail Piece
1
1
1
2
1
2
2
1
1
1
1
1
—
1
—
1
—
1
—
1
—
1
1
1
1
1
1
1
1
2
—
1
1
3
2
3
1
1
2
1
1
1
1
1
1
1
1
2
1
2
2
1
1
1
1
—
—
—
1
—
1
—
1
—
1
—
1
1
1
1
1
1
1
2
—
1
1
3
2
3
1
1
2
1
1
1
1
1
Circle
54"
Qty
36"
Qty
—
1
1
2
1
4
4
1
1
1
—
—
1
1
—
1
—
1
—
1
—
1
1
1
1
1
1
1
1
2
1
1
1
3
—
3
1
1
2
1
1
1
1
1
—
1
1
2
1
4
4
1
1
1
—
—
1
—
1
—
1
—
1
—
1
—
1
1
1
1
1
1
1
2
1
1
1
3
—
3
1
1
2
1
1
1
1
1
If any of these valves are desired complete with t ail pieces, tail piece nuts and washers, order as follows:
S60-003S, S01-038S, S01-522S
Not Illustrated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Washfountain Fittings
Type B Vent – Foot Control – (Semi-Circular shown)
Complete Soap Assemblies
Items 1 through 8 comprise a complete soap dispenser
assembly. For a complete assembly, order as follows:
S11-150 Nylon LSD
—
Semi-circular
S11-159 Nylon PSD
—
Semi-circular
S11-186 Metal LSD
—
Semi-circular
S11-195 Metal PSD
—
Semi-circular
S11-132 Nylon LSD
—
Circular
S11-141 Nylon PSD
—
Circular
S11-168 Metal LSD
—
Circular
S11-177 Metal PSD
—
Circular
TYPE "B" DRAIN
1
2
3
For washfountains without soap dispensers,
delete items 4 through 8.
PARTS SHOWN IN
BOX ARE FOR
UNITS WITH SOAP
DISPENSER.
4
7
8
25
10
24
9
26
22
17
12
20
16
20
14
22
13
18
17
21
11
15
19
22
23
21
20
See Pages 24-26
Optional Vernatherm
Thermostatic Mixing Valve
Parts List on next page
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
13
Bradley Washfountains
Parts and Service Guide
Washfountain Fittings ....Continued
Type B Drain – Foot Control
Parts List
•
**
14
See previous page for panel item listing
Semi &
Corner
54"
36"
Qty
Qty
Item
Part No.
Description
1
2
3
4
7
**
8
9
9
9
10
10
11
11
11
11
11
12
**
**
**
**
**
13
13
14
15
15
16
•17
**
18
•19
20
21
22
•23
24
25
26
26
160-108
107-185
159-020
S10-004
S09-010A
S09-007S
113-155A
S05-054B
S05-054C
S05-054
S57-005
S57-006
113-125A
113-124A
113-123A
113-122A
113-245
173-002
160-044
112-015
112-016
142-068
161-021
125-008
125-011
111-024
S14-007
S14-007A
S07-066
S60-003
159-019
S02-045
S01-038
110-005
129-007
124-001AF
S01-525
129-009
169-174
113-852
113-006AL
Cap Screw
Dispenser Cover – Type B
Tie Bar
Nylon Filler Hole Cap
Powdered Soap Valve
Liquid Soap Valve – Brass
Nylon Support Tube Spacer
Sprayhead, Semi-Circle Units
Sprayhead, Corner Units
Sprayhead, Circular Units
Sprayhead Support Tube
Sprayhead Support Tube
Supply Pipe, Terrazzo or Terreon® Bowl
Supply Pipe, Terrazzo or Terreon® Bowl
Supply Pipe, Stainless Steel Bowl
Supply Pipe, Stainless Steel, Terreon® or Bradstone Bowl
Supply Pipe, Bradstone Bowl
Strainer
Strainer Screw
Drain Spud, Terrazzo, Terreon® or Bradstone Bowl
Drain Spud, Stainless Steel Bowl
Washer
Drain Spud Lock Nut
Support Tube Gasket, Stainless Steel Bowl
Support Tube Gasket, All Other Bowls
Vented Trap
Operating Rod Assy., Std. Ht.
Operating Rod Assy., Juv. Ht.
Foot Valve
Combination, Stop, Strainer, Check Valve
Operating Cross
Volume Control Valve
Manual Mixing Valve
Tail Piece Nut
Tail Piece Unplated
Tail Piece Washer – Fiber
Vernatherm Assy. — Thermostatic Mixing Valve
Foot Valve Tail Piece
3/8" Coupling
Nipple 2" Long, Std Height
Close Nipple, Juv Height
2
1
1
2
2
2
1
1
1
—
1
—
1
—
1
—
1
1
2
1
1
1
1
1
1
1
1
1
1
2
—
1
1
3
2
3
1
1
1
1
1
2
1
1
2
2
2
1
1
1
—
—
1
—
1
—
1
—
1
2
1
1
1
1
1
1
1
1
1
1
2
—
1
1
3
2
3
1
1
1
1
1
Circle
54"
Qty
36"
Qty
2
1
1
2
4
4
1
—
—
1
1
—
1
—
1
—
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
2
3
1
1
1
1
1
2
1
1
2
4
4
1
—
—
1
—
1
—
1
—
1
—
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
2
3
1
1
1
1
1
If any of these valves are desired complete with t ail pieces, tail piece nuts and washers, order as follows:
S60-003S, S01-038S, S01-522S
Not Illustrated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Bowls — Replacement Part Numbers
Terreon® Replacement Bowls
Part No.
Terrazzo Replacement Bowls
Part No.
Configuration
Color
Configuration
Color
S45-1952AA
54" Semi-Circular Bowl
Soapstone Gray
S16-070
54" Semi-Circular Bowl
Granito
S45-1952AB
54" Semi-Circular Bowl
Canyon Tan
S16-071
54" Semi-Circular Bowl
White Marmorite
S45-1977AA
36" Semi-Circular Bowl
Soapstone Gray
S16-074
36" Semi-Circular Bowl
Granito
S45-1977AB
36" Semi-Circular Bowl
Canyon Tan
S16-075
36" Semi-Circular Bowl
White Marmorite
S45-1962AA
54" Circular Bowl
Soapstone Gray
S16-066
54" Circular Bowl
Granito
S45-1962AB
54" Circular Bowl
Canyon Tan
S16-067
54" Circular Bowl
White Marmorite
S45-1965AA
36" Circular Bowl
Soapstone Gray
S16-072
36" Circular Bowl
Granito
S45-1965AB
36" Circular Bowl
Canyon Tan
S16-073
36" Circular Bowl
White Marmorite
*S16-013
54" Corner Bowl
Granito
*S16-013D
54" Corner Bowl
White Marmorite
Attaching Brackets For
Terreon Bowls
Part No.
Configuration
*S45-1932
Semi-Circular
*S45-1933
Circular
Color
* Foot rails are included with corner bowls.
* These brackets are required when replacing
terrazzo Bowls with Terreon® (no other bowls are
directly interchangeable).
Stainless Steel Replacement Bowls
Part No.
Configuration
Color
Bradstone Replacement Bowls
Part No.
Configuration
Color
S18-634
54" Semi-Circular Bowl
N/A
S38-067
54" Semi-Circular Bowl
Sandbox
S18-636
36" Semi-Circular Bowl
N/A
S38-068
54" Semi-Circular Bowl
Carbon
S18-633
54" Circular Bowl
N/A
S38-071
36" Semi-Circular Bowl
Sandbox
S18-635
36" Circular Bowl
N/A
S38-072
36" Semi-Circular Bowl
Carbon
S38-065
54" Circular Bowl
Sandbox
S38-066
54" Circular Bowl
Carbon
S38-069
36" Circular Bowl
Sandbox
S38-070
36" Circular Bowl
Carbon
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
15
Bradley Washfountains
Parts and Service Guide
Pedestals — Circular Washfountains
1
2
3
2
1
4
3
4
5
4
6
6
7
7
FOR TAPERED PANELS
Fits Bradstone bowls only
FOR STANDARD PANELS
Fits Terrazzo and Stainless Steel bowls
11
8
12
9
13
FOR TERREON
BOWL ONLY
10
14
FOR BRADSTONE BOWL ONLY
NOTE: Foot control linkage shown in illustrations is not p art of
pedestal. See specific parts sheet for identification.
Parts List
54"
*
Item
Part No.
Description
1
1
2
3
4
4
5
*
*
6
7
7
8
9
10
11
12
13
14
194-005
194-006
161-040
160-104
193-002
193-002B
140-291
160-320
142-002CA
160-060A
185-015A
185-016A
160-069
161-047
140-141
140-747
142-002BJ
142-002X
161-076
Frame Member
Frame Member
Nut
Stove Bolt
Leg, Standard Height
Leg, Juvenile Height
Panel Bracket, Bradstone Bowl only
Panel Screw
Taper Panel Screw Washer, Bradstone only
Carriage Bolt, Plated
Scuff Base
Scuff Base
Screw, Bradstone Bowl only
Nut, Bradstone Bowl only
Bracket, Bradstone Bowl only
Bracket — Terreon Bowl only
Washer, Round — Terreon Bowl only
Washer, Split — Terreon Bowl only
Nut — Terreon Bowl only
36"
Qty
4
—
28
12
4
4
4
28
16
16
4
—
8
8
4
4
8
4
4
—
4
28
12
4
4
—
16
16
16
—
4
8
8
4
4
8
4
4
Not Illustrated.
16
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Pedestals — Semi-Circular Washfountains
1
5
1
2
5
4
6
3
6
3
6
2
4
7
9
10
10
9
8
8
FOR TAPERED PANELS
Fits Bradstone bowls only
FOR STANDARD PANELS
Fits Terrazzo and Stainless Steel bowls
14
15
11 12
16
FOR TERREON
BOWL ONLY
17
13
FOR BRADSTONE BOWL ONLY
NOTE: Foot control linkage shown in illustrations is not
part of pedestal. See specific parts sheet for identification.
Parts List
54"
*
Item
Part No.
Description
1
2
1
2
1
2
1
2
3
4
4
140-040LH
140-040RH
140-041LH
140-041RH
140-188LH
140-188RH
140-189LH
140-189RH
161-040
194-005
194-006
Wall Bracket, Terrazzo & Terreon® Bowl
Wall Bracket, Terrazzo & Terreon® Bowl
Wall Bracket, Terrazzo & Terreon® Bowl
Wall Bracket, Terrazzo & Terreon® Bowl
Wall Bracket, Stainless Steel & Bradstone Bowl
Wall Bracket, Stainless Steel & Bradstone Bowl
Wall Bracket, Stainless Steel & Bradstone Bowl
Wall Bracket, Stainless Steel & Bradstone Bowl
Nut For Frame Member, Scuff Base
Frame Member
Frame Member
Not Illustrated.
36"
Qty
1
1
—
—
1
1
—
—
21
2
—
—
—
1
1
—
—
1
1
21
—
2
Table continued on next page
Bradley Corporation • 215-1370 Rev. N; EN 12-00-14
17
Bradley Washfountains
Parts and Service Guide
Pedestals — Semi-Circular Washfountains...Continued
Parts List...Continued
54"
,
*
Item
Part No.
5
6
*
7
8
9
9
10
10
10
10
11
12
13
*
*
14
15
16
17
160-104
193-002
193-002B
140-291
160-060A
185-015A
185-016A
S45-217A
S45-227A
S45-214A
S45-224A
160-069
161-047
140-141
160-320
142-002CA
140-747
142-002BJ
142-002X
161-076
Description
36"
Qty
Stove Bolt For Frame Member
Leg, Standard Height
Leg, Juvenile Height
Panel Bracket, Bradstone only
Carriage Bolt, Stainless Steel Scuff Base
Scuff Base (All)
Scuff Base (All)
Scuff Base Ends, Bradstone & St ainless Steel Bowl (Set R & L)
Scuff Base Ends, Bradstone & St ainless Steel Bowl (Set R & L)
Scuff Base Ends, Terrazzo & Terreon, Bowl (Set R & L)
Scuff Base Ends, Terrazzo & Terreon, Bowl (Set R & L)
Screw, Bradstone only
Nut, Bradstone Bowl only
Bracket Bradstone Bowl only
Panel Screw
Taper Panel Screw Washer, Bradstone only
Bracket — Terreon Bowl only
Washer, Round — Terreon Bowl only
Washer, Split — Terreon Bowl only
Nut — Terreon Bowl only
9
3
3
3
12
2
—
1
—
1
—
6
6
3
21
12
3
6
3
3
9
3
3
—
12
—
2
—
1
—
1
6
6
3
12
12
3
6
3
3
Not Illustrated.
18
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Pedestals — Corner Washfountains
6
NOTE: Foot control linkage shown in illustrations is not p art
of pedestal. See specific parts sheet for identification.
Parts List
54"
*
Item
Part No.
Description
Qty
1
2
3
3
4
5
6
6
7
8
9
10
11
12
12
13
*
140-146LH
161-040
194-043
194-043A
194-005
S45-234A
193-002
193-002B
194-041
160-104
185-015A
140-146RH
194-042
193-006
193-006A
160-060A
160-320
Wall Bracket
Nut
Diagonal Support, Standard Height
Diagonal Support, Juvenile Height
Frame Member
Scuff Base Ends, (Set R & L)
Leg, Standard Height
Leg, Juvenile Height
Lower Support
Stove Bolt
Scuff Base
Wall Bracket
Upper Support
Corner Leg, Standard Height
Corner Leg, Juvenile Height
Carriage Bolt, Stainless Steel, Scuff base
Panel Screw
1
24
2
2
1
1
2
2
2
14
1
1
2
1
1
10
8
Not Illustrated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
19
Bradley Washfountains
Parts and Service Guide
Panels — Circular Pedestal Panels for Stainless Steel, Terrazzo,
and Terreon® Bowls
1
See Page 15 for
panel screws.
Parts List
54"
Item
1
1
1
1
20
Part No.
Description
186-006A
186-018A
186-005A
186-016A
Stainless
Stainless
Stainless
Stainless
Steel
Steel
Steel
Steel
36"
Qty
Center Panel
Juvenile Height Center Panel
Center Panel
Juvenile Height Center Panel
—
—
4
4
4
4
—
—
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Panels — Semi-Circular Pedestal Panels for Terrazzo and
Terreon® Bowls
1
2
2
See Pages 17-18 for
panel screws.
Parts List
54"
Item
1
2
2
2
1
2
1
2
Part No.
Description
186-006A
S45-225A
186-018A
S45-226A
186-005A
S45-215A
186-016A
S45-216A
Stainless
Stainless
Stainless
Stainless
Stainless
Stainless
Stainless
Stainless
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Center Panel
Rear Panels (Set R & L)
Juvenile Height Center Panel
Juvenile Height Rear Panels (Set R & L)
Center Panel
Rear Panels (Set R & L)
Juvenile Height Center Panel
Juvenile Height Rear Panels (Set R & L)
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
36"
Qty
—
—
—
—
2
1
2
1
2
1
2
1
—
—
—
—
21
Bradley Washfountains
Parts and Service Guide
Panels — Semi-Circular Pedestal Panels for Stainless Steel Bowls
2
2
1
See Pages 17-18 for
panel screws.
Parts List
54"
Item
1
2
1
2
1
2
1
2
22
Part No.
Description
186-006A
S45-228A
186-018A
S45-229A
186-005A
S45-218A
186-016A
S45-219A
Stainless
Stainless
Stainless
Stainless
Stainless
Stainless
Stainless
Stainless
Steel
Steel
Steel
Steel
Steel
Steel
Steel
Steel
36"
Qty
Center Panel
Rear Panels (Set R & L)
Juvenile Height Center Panel
Juvenile Height Rear Panels (Set R & L)
Center Panel
Rear Panels (Set R & L)
Juvenile Height Center Panel
Juvenile Height Rear Panels (Set R & L)
—
—
—
—
2
1
2
1
2
1
2
1
—
—
—
—
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Panels — Pedestal Panels for Bradstone Bowls
1
1
3
2
Semi-Circular
See Pages 17-18 for
panel screws and washers.
Circular
See Page 16 for
panel screws and washers.
Semi- Circular Parts List
54"
Item
1
1
2
2
3
3
1
1
2
2
3
3
Part No.
Description
186-879
186-879B
186-880
186-880B
186-182A
186-182B
186-877
186-877B
186-878
186-878B
186-157A
186-157B
Left Rear Panel – Almond
Left Rear Panel – Gray
Right Rear Panel – Almond
Right Rear Panel – Gray
Center Panel – Almond
Center Panel – Gray
Left Rear Panel – Almond
Left Rear Panel – Gray
Right Rear Panel – Almond
Right Rear Panel – Gray
Center Panel – Almond
Center Panel – Gray
36"
Qty
—
—
—
—
—
—
1
1
1
1
2
2
1
1
1
1
2
2
—
—
—
—
—
—
54"
36"
Circular Parts List
Item
1
1
1
1
Part No.
Description
186-182A
186-182B
186-157A
186-157B
Center
Center
Center
Center
Panel – Almond
Panel – Gray
Panel – Almond
Panel – Gray
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Qty
—
—
4
4
4
4
—
—
23
Bradley Washfountains
Parts and Service Guide
Panels — Corner Washfountain Stainless Steel Pedestal Panels
See Page 19 for
panel screws.
Parts List
54"
Item
1
2
1
2
24
Part No.
Description
S45-235A
186-005A
S45-236A
186-016A
Stainless
Stainless
Stainless
Stainless
Steel
Steel
Steel
Steel
Qty
Rear Panels (Set R & L)
Center Panel
Juvenile Height Rear Panels (Set R & L)
Juvenile Height Center Panel
1
1
1
1
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Linkage — Circular Washfountain Foot Control
Note: * Pedestal Leg shown on Pedestal drawings.
Note:
U-bracket is part of pedestal leg.
Parts List
54"
Item
1
1
2
2
3
4
5
6
7
Part No.
Description
143-025
143-027
S25-016
S25-015
166-004
159-019
166-003
152-026
135-001W
Foot Lever
Foot Lever
Foot Rail Assembly
Foot Rail Assembly
Spring Clip Fastener
Operating Cross
Cotter Pin
Pivot Pin
Foot Lever Spring
36"
Qty
4
—
1
—
8
1
4
4
4
—
4
—
1
8
1
4
4
4
NOTE: Items 3 through 7 are available in a Prep ack. Order Part number S45-003.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
25
Bradley Washfountains
Parts and Service Guide
Linkage — Semi-Circular Washfountain Foot Control
Note: * Pedestal Leg shown on
Pedestal drawings.
Note:
U-bracket is part of pedestal leg.
Parts List
54"
Item
Part No.
Description
1
1
2
2
3
4
5
6
7
8
9
10
10
11
143-025
143-027
S25-018
S25-017
166-004
135-001W
152-026
161-007
142-002BC
142-002AM
142-020
160-065
160-043
160-082
Foot Lever
Foot Lever
Foot Rail Assembly
Foot Rail Assembly
Spring Clip Fastener
Foot Lever Spring
Pivot Pin
Jam Nut
Shakeproof Washer
Flat Washer
Ribbed Washer
Pivot Bolt
Pivot Bolt
Elevator Bolt
36"
Qty
1
—
1
—
2
1
1
4
2
2
2
2
—
2
—
1
—
1
2
1
1
4
2
2
2
—
2
2
NOTE: Items 3 through 11 are available in a Prepack. Order as follows:
Part number S45-004
36" Washfountain
Part number S45-004A
54" Washfountain
26
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Linkage — Corner Washfountain Foot Control
Note: * Pedestal Leg shown on Pedestal drawings.
Note:
U-bracket is part of pedestal leg.
Parts List
54"
Item
1
2
3
4
5
6
7
8
9
Part No.
Description
143-042
166-004
182-044
152-036
S25-021
135-001W
152-026
166-003
159-019
Foot Lever
Spring Clip Fastener
Spacer
Spring Pin
Foot Rail Assembly
Foot Lever Spring
Pivot Pin
Cotter Pin
Operating Cross
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Qty
2
4
2
2
1
2
2
2
1
27
Bradley Washfountains
Paper Towel Dispensers
Circular Washfountains
Parts and Service Guide
11
2
3
4
5
6
7
8
2
3
9
10
Parts List
54"
Item
Part No.
Description
n 2
n 3
4
*
5
6
*
n 7
8
8
9
159-020
160-208
S78-001
S78-002
S70-123
113-170
113-168
160-111
107-048
107-185
—
10
S70-082
Tie Bar
Tie Bar Screw, #10-24 x 3/8" Hex Head (Totals for 2 Tie Bars)
Towel Dispenser, C-fold or multi-fold
Towel Dispenser, Single fold
Towel Dispenser Mounting Bracket
Shroud Tube (Washfountains w/Soap Dispenser)
Shroud Tube (Washfountains Less Soap Dispenser)
Cap Screw for Tie Bar, 1/4-20 x 1/2" Hex Head
Cover - Type “H” Drain or Type “A” w/ Towel Dispensers
Cover - Type “B” Drain or Type “O” w/ Towel Dispensers
Vent Pipe or Support Pipe
(Not furnished by Bradley Corporation)
Tie Pipe Bracket
(Furnished only for washfountains without centrally rising vents)
Pipe Cap (For washfountains without centrally rising vents)
n 11
n
*
169-986A
36"
Qty
2
6
3
3
2
1
1
4
1
1
1
2
6
3
3
2
1
1
4
1
1
1
1
1
1
1
Prepack S45-205
Not Illustrated.
28
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Paper Towel Dispensers
Circular Washfountains with Shroud
2
3
5
4
6
7
9
8
10
Parts List
54"
Item
*
Part No.
Description
2
*
3
*
4
5
6
7
8
9
S78-001
S78-002
S70-095
160-169
160-138
160-111
S04-029
159-020
160-208
—
10
S70-082
Towel Dispenser, C-fold or multi-fold
Towel Dispenser, Single fold
Towel Dispenser Mounting Bracket
Screw to Mount Brackets, 1/4-20 x 13/32" Round Head
Screw to attach shroud to cover, #10-24 x 1/2" Button Head
Cap Screw for Tie Bar, 1/4-20 x 1/2" Hex Head
Cover for Soap Dispensers or Sprayhead, All Supply Types
Tie Bar
Tie Bar Screw, #10-24 x 3/8" Hex Head
Vent Pipe or Support Pipe
(Not Furnished by Bradley Coporation)
Tie Pipe Bracket Assembly
(Furnished only for washfountains without centrally rising vents)
36"
Qty
3
3
2
6
3
2
1
—
3
1
3
3
2
6
3
2
1
1
3
1
1
1
Not Illustrated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
29
Bradley Washfountains
Paper Towel Dispensers
Semi-circular Washfountains
Parts and Service Guide
11
1
2
3
4
5
6
7
8
2
3
9
10
Parts List
54"
Item
Part No.
Description
1
1
1
1
n2
n3
4
*
5
6
*
n7
8
8
9
140-212
140-212A
140-212B
140-212C
159-020
160-208
S78-001
S78-002
S70-123
113-170
113-168
160-111
107-048
107-185
—
Restraining Bracket, Terrazzo or Terreon® Bowl
Restraining Bracket, Terrazzo or Terreon® Bowl
Restraining Bracket, Stainless Steel or Bradstone Bowl
Restraining Bracket, Stainless Steel or Bradstone Bowl
Tie Bar
Tie Bar Screw, #10-24 x 3/8" Hex Head (Totals for 2 Tie Bars)
Towel Dispenser, C-fold or multi-fold
Towel Dispenser, Single fold
Towel Dispenser Mounting Bracket
Shroud Tube (Washfountains w/Soap Dispenser)
Shroud Tube (Washfountains Less Soap Dispenser)
Cap Screw for Tie Bar, 1/4-20 x 1/2" Hex Head
Cover - Type “H” Drain or Type “A” w/ Towel Dispensers
Cover - Type “B” Drain or Type “O” w/ Towel Dispensers
Vent Pipe or Support Pipe
(Not furnished by Bradley Corporation)
Tie Pipe Bracket
(Furnished only for washfountains without centrally rising vents)
Pipe Cap (For washfountains without centrally rising vents)
10
n 11
n
*
30
S70-082
169-986A
36"
Qty
—
2
—
2
2
6
2
2
2
1
1
4
1
1
1
2
—
2
—
2
6
2
2
2
1
1
4
1
1
1
1
1
1
1
Prepack S45-205
Not Illustrated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Paper Towel Dispensers
Semi-circular Washfountains with Shroud
1
2
3
5
4
6
7
8
9
10
Parts List
54"
Item
Part No.
Description
1
1
1
1
2
*
3
*
4
n 5
6
n 7
n 8
9
140-212
140-212A
140-212B
140-212C
S78-001
S78-002
S70-095
160-169
160-138
160-111
S04-029
159-020
160-208
—
Restraining Bracket, Terrazzo or Terreon® Bowl
Restraining Bracket, Terrazzo or Terreon® Bowl
Restraining Bracket, Stainless Steel or Bradstone Bowl
Restraining Bracket, Stainless Steel or Bradstone Bowl
Towel Dispenser, C-fold or multi-fold
Towel Dispenser, Single fold
Towel Dispenser Mounting Bracket
Screw to Mount Brackets, 1/4-20 x 13/32" Round Head
Screw to attach shroud to cover, #10-24 x 1/2" Button Head
Cap Screw for Tie Bar, 1/4-20 x 1/2" Hex Head
Cover for Soap Dispensers or Sprayhead, All Supply Types
Tie Bar
Tie Bar Screw, #10-24 x 3/8" Hex Head
Vent Pipe or Support Pipe
(Not Furnished by Bradley Corporation)
Tie Pipe Bracket Assembly
(Furnished Only for Washfountains Without Centrally Rising Vents)
10
n
*
S70-082
36"
Qty
—
2
—
2
3
3
2
6
3
2
1
1
3
1
2
—
2
—
3
3
2
6
3
2
1
1
3
1
1
1
Prepack S45-205
Not Illustrated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
31
Bradley Washfountains
Parts and Service Guide
Restraining Brackets
Support Tube
Semi-Circle
Corner
Parts List
Part No.
Description
Qty
140-124
54" Bradstone and Stainless
1
140-126
54" Terrazzo and Terreon
1
140-196
36" Bradstone and Stainless
1
140-128
36" Terrazzo and Terreon
1
S70-061E
54" Terrazzo Corner
1
NOTE: B or H Drains do not require restraining bracket since
1-1/2" vent pipe provides additional support.
32
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Foot Valve (Jan. 2003 to present)
Parts List
7
6
Item
8
5
9
4
10
3
11
2
S07-066 Foot Valve
Part No.
Qty
Description
1
118-302
1
Foot Valve Body
2
125-154
1
O-Ring
3
118-300
1
Foot Valve Cover (blue)
4
135-088
1
Spring
5
117-016
1
Valve Seat
6
S64-093
1
Plunger Assembly
7
125-001Y
1
Diaphragm
8
179-002
1
Plunger Guide
9
119-024
1
Plunger
10
143-026
1
Operating Lever
11
110-101
1
Bottom Nut
12
124-001V
1
Washer - Black Phenolic
NOTE: This valve can be identified by the color of Item 3.
1
12
Parts List
Item
Part No.
S65-230
8
Foot Valve Repair Kit
Qty
Description
1
118-300
1
Foot Valve Cover
2
135-088
1
Spring
3
125-154
1
O-Ring
4
S64-093
1
Plunger Assembly
5
117-016
1
Valve Seat
6
125-001Y
1
Diaphragm
7
124-001V
1
Washer - Black Phenolic
8
130-033
1
Key-Valve Seat
9
S45-125
1
Lubricant (not shown)
3
6
5
2
1
4
7
Operating
Lever
Foot Valve Linkage
Foot
Valve
(
S14-007
S14-007A
Jr. Ht.
)
Operating Rod
Standard Spring
Loaded Cartridge
Operating Cross
159-019 (CIRCLE)
or
Foot Lever
143-025 (54" SEMI)
143-027 (36" SEMI)
For normal operation using the standard operating
rod assembly, the spring loaded cartridge should
be adjusted so there is no play in the operating
lever. Care must be taken to insure that a snug fit
is achieved without engaging the operating lever,
or water will leak from the sprayhead.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
33
Bradley Washfountains
Parts and Service Guide
Foot Valve (Nov. 1973 to Jan. 2003)
Parts List
5
3
2
4
6
Item
7
8
9
11
10
12
14
13
Description
110-095
1
Body-Needle Valve
S21-027
1
Needle Assembly
3
S64-006
1
Valve Plunger Assembly
*4
118-021
1
Valve Body (No longer available)
5
125-001Y
1
Diaphragm
6
179-002
1
Plunger Guide
7
110-101
1
Bottom Nut
8
143-026
1
Operating Lever
9
135-001P
1
Spring
10
125-001BW
1
Gasket
11
117-016
1
Renewable Valve Seat
12
124-001V
1
Washer Black Phenolic
13
119-024
1
Operating Plunger
14
179-002
1
Plunger Guide
15
119-024
1
Plunger
Valve body no longer available,
replace with S07-066 (Complete Valve)
1
Parts List
Qty
2
*
Item
Part No.
1
1
15
S07-015 Foot Valve
2
6
S65-001A Foot Valve Repair Kit
Part No.
Qty
Description
1
S21-027
1
Needle Assembly
2
125-001BW
1
Gasket
3
S64-006
1
Valve Plunger Assembly
4
117-016
1
Valve Seat
5
125-001Y
1
Diaphragm
6
124-001V
1
Fiber Washer
7
110-095
1
Body-Needle Valve
8
135-001P
1
Spring
9
130-033
1
Key-Valve Seat
5
3
4
8
Repairs All Foot Valves Furnished Since April 1943 to Jan. 2003.
7
9
Operating
Lever
Foot Valve Linkage
Foot
Valve
(
34
S14-007
S14-007A
Jr. Ht.
)
Operating Rod
Standard Spring
Loaded Cartridge
Operating Cross
159-019 (CIRCLE)
or
Foot Lever
143-025 (54" SEMI)
143-027 (36" SEMI)
For normal operation using the standard operating
rod assembly, the spring loaded cartridge should
be adjusted so there is no play in the operating
lever. Care must be taken to insure that a snug fit
is achieved without engaging the operating lever,
or water will leak from the sprayhead.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Foot Valve Adjustment Instructions (November 1973 to Jan. 2003)
(Valves made from Jan. 2003 to present require no adjustment s)
Adjusting Needle
Relief
Ports
Spring
Seat
Flexible Rubber
Ring (Closed)
Operating
Lever
Needle
Valve
Orifice
O Rings
Plunger
I. CLOSED POSITION:
PLUNGER SEATED.
NO WATER FLOW.
(Needle Valve is used to
prevent water hammer)
II. OPENING POSITION:
III.CLOSING POSITION:
a) Valve actuated - plunger pushed off seat
As operating lever is released, plunger
moves back towards seat, pushed by the
— water flows through seat to sprayhead.
spring, but retarded by flow of water to
b) As opening cycle starts and water within
sprayhead and vacuum created by
the hollow plunger assembly is pushed out
displacement of water behind plunger.
through restricted needle valve orifice, presBypass water moving through needle
sure is relieved through ports covered with
valve orifice fills vacuum and helps to
flexible rubber ring, allowing valve to open
return plunger to seat. Speed of closure
easily. Rubber ring acts as check valve,
controlled by volume of water allowed
preventing back flow through parts which
through needle valve.
would defeat slow closing feature of the
valve.
The adjusting needle controls the closing, or shut of f speed of valve. Turning the adjusting needle clockwise retards closing. This
adjustment corrects water hammer problems. Turning the adjusting needle counterclockwise speeds closing. Any needle valve
adjustments should be slight, not more than 1/4 turn at a time until the desired rate of shut of f is achieved.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
35
Bradley Washfountains
Parts and Service Guide
Stop, Strainer and Check Valve
S60-003
—
S60-003A —
S60-003S —
S60-003AS —
Brass Valve Only
Plated Valve Only
Brass Valve with Tailpieces, Nuts and Washers
Plated Valve with Tailpieces, Nuts and Washers
1
2
Above include S21-014 Celcon plastic stop assembly.
3
4
Parts List
Stop
Item
3
4
2
5
6
Stop Assembly S21-014
Standard Celcon Core
Part No.
Qty
1
Description
1
119-057
Valve Core
*2
125-001AW
1
“O” Ring
*3
125-001L
1
Bibb Washer
4
160-164
1
Screw
Strainer
1
1
8
2
1/2" NPT
1/2" NPT
9
11
5
10
6
Parts List
Item
Part No.
S60-003
Check
Stop, Strainer and Check Valve
Qty
Description
1
118-039
1
Valve Body - Brass
1
118-039A
1
Valve Body - Plated
2
160-131
1
Set Screw
3
S21-014
1
Stop Assembly - Celcon
3
S21-026
1
Stop Assembly - Brass
*4
156-006
1
Strainer
*5
124-001BV
2
Fiber Washer
*6
153-068
2
Plug - Brass
7
129-007
1
Tail Piece - Brass
7
129-007A
1
Tail Piece - Plated
8
110-005
1
Tail Piece Nut - Brass
8
110-005A
1
Tail Piece Nut - Plated
*9
124-001AF
1
Tail Piece Washer
*10
135-001AB
1
Spring
*11
S21-015
1
Check Assembly
*
S45-050 Repair Kit Includes these parts
36
3
7
4
Parts List
Item
Stop Assembly S21-026
Optional Brass Core
Part No.
Qty
Description
1
119-038
1
Valve Core
*2
125-001AW
1
“O” Ring
*3
125-001L
1
Bibb Washer
4
160-146
1
Screw
1
2
Parts List
Item
Part No.
Check Assembly S21-015*
Qty
Description
1
119-091
1
Plunger
2
125-001BB
1
Washer
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Adjusting the Vernatherm Thermostatic Mixing Valve
(August, 2004 to Present)
NOTE: This valve is NOT factory preset. Upon installation, the temperature of this valve must be
checked and adjusted to ensure delivery of a safe water temperature. Water in excess of 110°F
(43°C) may cause scalding.
1. Check the temperature when approximately 1.0 GPM water flow is reached and adjust if necessary
(the range of the valve is 95°F–115°F (35°C–43°C). To adjust the temperature, follow the procedure below:
• Loosen temperature locking nut with wrench.
• Using a blade screwdriver, turn the adjustment stem counterclockwise to increase the temperature or clockwise to decrease the temperature.
• Once desired temperature has been reached, tighten lock nut to prevent change in temperature.
2. Shut the hot water inlet off by closing the hot water stop-strainer-check valve. While the hot
water supply is turned off, check to make sure the cold water flow is reduced. If the cold water is
reduced properly, reopen the hot water supply.
3. Shut the cold water inlet off by closing the cold water stop-strainer-check valve. While the cold
water supply is off, check to make sure that the hot water flow has shut down.
TEMPERATURE
ADJUSTMENT
STEM
TEMPERATURE
LOCKING
NUT
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
37
Bradley Washfountains
Parts and Service Guide
Thermostatic Mixing Valve Maintenance and Troubleshooting
(August, 2004 to Present)
NOTE: Before attempting to troubleshoot the valve or disassemble the components, check for the
following conditions:
• If stop/check valves are used, make sure that they are fully open
• Make sure that the hot and cold inlet pipes are connected properly, and that there are no
cross-connections or leaking stop/check valves
• check the hot water heater output to make sure that it is at least 20° F above the set temperature.
Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the
valves after inspection and repair is complete.
Problem: Limited water flow
Cause: Dirt and debris have built up in the valve.
Solution: Check the valve's piston for free and smooth movement, follow the procedures outlined
below:
1. Remove the valve's cap and thermostat (see Figure on next page).
2. Push down on the piston with your finger (the piston should move freely). If the movement is
not as it should be, the piston needs to be cleaned. Follow the method outlined below for
cleaning the piston and valve body:
• Remove the thermostat.
• Lift the piston out with a needle-nose pliers and remove the spring.
• Any cleaner suitable for brass and stainless steel may be used (if cleaning with suitable
cleaner is not sufficient to remove debris, a 400-grit sandpaper may be used to polish and
hone the piston and valve body).
• Snap spring into piston (will detent) and reassemble into the valve body.
• Retest the piston.
3. If, after a thorough cleaning, the piston does not move freely, the piston must be replaced.
Contact your Bradley representative and ask for Repair Kit (part number S65-259).
Problem: External leaks in the system
Cause: O-rings have been damaged.
Solution: Replace O-rings where necessary. For replacement of the O-rings, contact your
Bradley representative and ask for Repair Kit (part number S65-259).
Problem: Improper water temperature or temperature fluctuation
Cause: Thermostat is slowly failing or not working at all.
Solution: "Check the thermostat for proper operation".
1. At room temperature (80° F or less) remove cap and thermostat.
2. Place thermostat into container with 115° F water. The pushrod should pop out of the
thermostat approximately 1/10".
3. If thermostat pushrod does not pop out, the thermostat must be replaced. Contact your
Bradley representative and ask for Repair Kit (part number S65-259).
Cause: Valve temperature is not properly set.
Solution: "Adjust the temperature" per steps on previous page.
38
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Vernatherm Thermostatic Mixing Valve (S01-525) Parts List — Repair Kit S65-259
(August, 2004 to Present)
Parts List
Item
Part No.
S65-259
Qty
Valve Repair Kit
Description
5
S39-413
1
Thermostat
7
125-001BX
1
O-Ring
8
125-157
1
O-Ring
10 Nut 3/8-24 Hex Jam
9
Cap
8 O-Ring
7
O-Ring
6 Stem
5 Thermostat
4 Piston
3 Spring
2 Seal Cup
1 Valve Body
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
39
Bradley Washfountains
Parts and Service Guide
Mixing Valve — Vernatherm™ — Thermostatic (Prior to Aug, 2004)
*Repair kit S45-049 is pre-packaged and includes O-Ring, Flip Ring, Power Element and Spring.
Maintenance Instructions
1. Disassemble the Vernatherm™ Valve as shown,
being careful not to damage the power element.
Replace the element, if necessary.
2. If necessary, remove the old flip ring and replace
with a new ring.
NOTE: An old or worn flip ring may cause temperature
fluctuation and/or water chatter.
Body
S73-027
Body (chrome)
S73-028
Power Element*
S27-019
Flip Ring*
125-015
3. Reassemble the power element and valve body.
Apply grease to the main valve slide and gently ease
into position, rotating so that grease is applied to the
flip ring. Do not force the slide as this may push the
flip ring from its position. To test, rotate the slide; a
slight drag should be felt when correctly installed.
4. Reassemble the valve.
Valve Slide
S01-039
Spring*
135-008
O-Ring*
125-001CH
Cover
107-261B
Screw
160-175
Service Suggestions
When servicing the Vernatherm™ valve, make sure it is installed in the correct position. The most
common error that occurs is when the valve is installed in the reversed position, that is, the hot line is
connected to the cold line and the cold is connected to the hot.
NOTE: A red ring is painted on the hot side of the valve.
The table below lists conditions that occur when the valve is installed correctly, and when it is in the
reversed position.
IF
Valve Position is
40
THEN
Hot Supply
Cold Supply
Valve Delivers
Correct
Hot
Cold
Mixed 107°
Correct
Hot
No Water
Valve shuts off or drips
Correct
No Water
Cold
Valve shuts off or drips
Correct
Hot
Hot
Hot
Correct
Cold
Cold
Cold
Reversed
Hot
Cold
Cold/below 107° Hot/above 107°
Reversed
Hot
No Water
Hot
Reversed
No Water
Cold
Cold
Reversed
Hot
Hot
Hot
Reversed
Cold
Cold
Cold
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Mixing Valve — Manual — S01-038
4
5
3
6
2
7
1
1/2
14 NPT male
Manual Mixing Valve Parts List
Valve
Assembly
S01-038
Item
1
1
2
3
4
5
6
6
7
7
*
*
*
*
*
*
Part No.
118-034
118-034A
124-001BD
125-001BC
119-059
152-038
121-016
121-016A
160-197
160-189
129-007
110-005
129-007A
110-005A
124-001AF
Valve
Assembly
S01-038S
Description
Mixing Valve Body - Brass
Mixing Valve Body - Chrome
Fiber Washer
O-Ring
Mixing Valve Core
Roll Pin
Bonnet - Brass
Bonnet - Chrome
Screw - Brass
Screw - Stainless Steel
Tailpiece - Brass
Tailpiece Nut - Brass
Tailpiece - Chrome
Tailpiece Nut - Chrome
Tailpiece Washer
Valve
Assembly
S01-038A
Valve
Assembly
S01-038AS
Repair Kit
S45-197
—
1
1
1
1
1
—
1
—
1
—
—
2
2
2
—
—
1
1
1
1
1
—
—
—
—
—
—
—
2
Qty
1
—
1
1
1
1
1
—
1
—
—
—
—
—
—
1
—
1
1
1
1
1
—
1
—
2
2
—
—
2
—
1
1
1
1
1
—
1
—
1
—
—
—
—
—
Parts not shown
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
41
Bradley Washfountains
Parts and Service Guide
Volume Control Valve Repair Parts — S02-045
2
3
4
1
5
1/2 – 14 NPT female
6
1/2
14 NPT male
Volume Control Valve Parts List
Item
1
2
3
3
4
5
6
6
42
Part No.
125-001BC
152-038
121-016
121-016A
124-001BD
119-060
118-033
118-033B
Description
O-Ring
Roll Pin
Bonnet
Bonnet
Fiber Washer
Valve Core
Valve Body
Valve Body
Brass
Valve
S02-045
1
1
1
—
1
1
1
—
Chrome
Valve
S02-045A
Qty
1
1
—
1
1
1
—
1
Repair Kit
S45-198
1
1
1
—
1
1
—
—
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Sprayheads — Standard w/Neoprene Spray Ring Grommet
NOTE: Repair kit does not include sprayhead
grommet. Order as a separate item.
1
2
4
5
3
9
7
10
6
8
Parts List
Sprayhead
Assembly
Item
1
2
3
4
5
6
7
8
9
9
9
10
Part No.
Description
125-001DE
139-031
124-001AL
160-211
115-061
116-008
124-001AT
161-025
124-020C
124-020D
124-020E
125-001DF
Neoprene Washer-Top
Sprayhead Manifold
Washer
Carriage Bolt
Sprayhead Top
Sprayhead Bottom
Washer
Nut
Sprayhead Grommet - Circle
Sprayhead Grommet - Semi-circle
Sprayhead Grommet - Corner
Neoprene Washer-Bottom
Repair Kit
S45-051
Qty
1
1
3
3
1
1
3
3
1
1
1
1
1
—
4
4
—
—
4
4
—
—
—
1
Sprayhead Service Suggestions
Problem: Water splashes over the rim of the bowl.
Cause: Foreign matter has reduced the size of the sprayhead slots, causing greater pressure at the open slots.
Solution: Clean the sprayhead:
1. Disassemble the sprayhead and dislodge any dirt, lime build-up and foreign debris with a wire brush.
2. Sprayheads with rubber grommet spray rings may be cleaned by rubbing a coin over the grommet.
3. Throttle down the volume control (water spray should strike the bowl without splashing outside of the bowl).
Problem: Water flow diminishes from the sprayhead.
Cause: Strainer portion of the stop-strainer-check valve is plugged.
Solution: Remove and clean the strainer screen from the stop-strainer-check valve.
NOTE: The sprayhead shown above includes a perforated neopreme spray ring grommet that is self-cleaning. The water pressure flexes
the spray holes which slows accumulation of foreign matter and tends to “break loose” any such deposits that may have accumulated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
43
Bradley Washfountains
Parts and Service Guide
Sprayhead Tubing Connections
NOTE: Flush supply lines before making connections.
Follow the procedures below and refer to Figures below when installing tubing to ensure that
you achieve a leakproof seal.
• Using a sharp razor, cut tubing squarely and remove any burrs. DO NOT pinch or crush end
of tubing.
• Loosen nut on fitting. Moisten end of tube and push into fitting until it is firmly seated.
Tighten nut to secure tube to fitting (make sure nut is securely tightened).
• If connector leaks, reseat tubing according to above procedure. If leaking persists,
replace male connector, or call your Bradley representative for assistance.
MALE
TUBE
CONNECTOR
269-626
NUT
SPRAYHEAD
TUBING
TUBING
44
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Soap Valve — Liquid — S09-007S
Parts List
3
Attaching
Parts
S09-007S
Item
1
2
3
4
5
*
*
*
Part No.
Description
118-025
110-007
135-001L
125-001BU
119-028
161-014
124-001D
142-002AH
Valve Body
Packing Nut
Spring
Washer
Plunger
Nut
Washer
Washer - Stainless Steel
1
Qty
4
1
1
1
1
1
1
2
1
5
2
* Not Illustrated
This valve delivers a measured amount of soap with each upward stroke. The soap dispenser has
been standard on washfountains since 1983 and is not well-suited for very thick lotion soaps.
NOTE: Lotion soap will clog liquid soap valves. Use only lotion soap valves with lotion soap.
Soap Valve — Lotion — S09-057S
Parts List
Valve
Assembly
S09-057
Item
1
2
3
4
5
6
7
8
Part No.
Description
124-001D
110-057
125-001AN
159-114
124-001AT
160-176
S09-040
S53-045
Washer
Nut
Stopper
Reinforcing Plate
Washer
Screw
Valve
Adaptor
Attaching
Parts
S09-057S
5
6
4
Qty
—
—
—
—
—
—
1
1
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
2
1
1
1
1
1
1
1
1
1
3
7
8
45
Bradley Washfountains
Parts and Service Guide
Soap Valve — Powdered — S09-010A
Parts List
Item
Part No.
1
Qty
Description
1
160-069
1
Screw, 1/4-20 RD
2
142-002X
1
Washer, 1/4 Split-Lock
3
S62-002
1
Agitator / Slide Assy.
4
192-004
1
Lever - Powdered Soap
2
3
NOTE: Reducer plugs are available for use with fine granulated
soap to reduce the flow.
NOTE: Valves can be changed from powdered to liquid by plugging
the innermost, or “bearing” hole with rubber plug, part number
125-001AK. To change from liquid to powdered, the plug must be
removed. If none is present, it will be necessary to drill out the
bearing hole with a 1/2" or 5/8" drill. The plastic container configuration forms a natural template for locating the bearing hole.
46
4
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Soap Maintenance Tips
SOAP RECOMMENDATIONS
Quality soap dispensers require good quality soap and periodic maintenance to properly operate. Bradley soap
dispensers will provide dependable, consistent operation over the long term when soap with reasonable viscosity and pH levels are used and when a minimal amount of periodic maintenance is performed on the valves.
Soap thickness is determined by a measurement called viscosity. Soap viscosity should be between 100 cps
(centerpoise) and 2500 cps for all Bradley soap dispensers. Thinner soaps are perceived by the users as being
"watered down" so users tend to take more than they need, resulting in waste. Thick soaps flow slower and
inhibit the "flushing" action of the valves, which allows the soap to congeal in the valve and cause clogs.
The pH (acid) level of the soap should be in the range of 6.5 to 8.5. More acidic soaps (pH levels lower than
6.5) will corrode metal parts (even stainless steel!!) and degrade rubber and plastic components. They will also
cause skin irritation. Most inexpensive soaps (typically the pink lotion type) fall into this acidic category and
will eventually cause valve failure and metal corrosion. Base soaps (pH levels higher than 8.5) will cause
swelling or degradation of rubber and plastic parts and skin irritation.
Generally, any quality soap meeting the viscosity and pH guidelines above will work well with Bradley soap
dispensers. PCMX or Isapropanol based antibacterial soaps (within viscosity and pH limits) will also work
with Bradley dispensers. Soaps satisfying these basic guidelines will provide consistent flow and reduce clogs.
Most soap dispenser problems are caused by soap that is too thick or corrosive, or by a lack of maintenance.
Many soaps come in concentrate form which must be diluted with water. Often, the soap is improperly diluted
or used straight out of the bottle, which causes clogging and valve failure. If proper soap is being used, valves
that have never been cleaned are usually the source of dispensing problems. Bradley has entered into an agreement with Champion Brand Products to provide additional customer service for purchasers of our dispensers
regarding soap issues. They are very helpful and can get to the bottom of almost any soap dispenser related
problem. They also sell an excellent "Bradley approved" soap. Please see Soap Instruction Sheet 215-1286
for details about soap valve cleaning or how to contact Champion. With proper maintenance and soap, Bradley
dispensers will provide long term, trouble free operation.
SOAP DISPENSER MAINTENANCE INSTRUCTIONS
Bradley soap dispensers will provide dependable, consistent operation over the long term when the proper
soap is used and when a minimal amount of periodic maintenance is performed on the valves. Valves must be
maintained (cleaned) to function properly.
To ensure proper operation of your soap dispenser, follow these instructions:
• Once per month, unscrew valve from reservoir and soak it for 30 minutes in hot water.
• Push valve at least 20 times while it is soaking.
• Flush soap reservoir with hot water while valve is soaking.
In cases of extreme clogging, the valve should be disassembled and the parts should be soaked in hot water or
cleaning solution to restore proper functioning. Soap dispensers that will not be used for extended periods of
time (schools during summer break, etc.) should be drained, cleaned and left empty until put back into service.
Soap left on the outside of dispensers can cause discoloration and corrosion of the reservoir (even on stainless
steel units). All soap should be wiped or scrubbed off daily, then the outside of the dispenser should be rinsed
with clear water and dried with a soft cloth.
Bradley Corporation • 215-1370 Rev. M; EN N12-00-014
47
Bradley Washfountains
Parts and Service Guide
Infrared Module — AccuZone® (Terrazzo and Stainless Steel Bowls;
Bradstone Bowls Prior to September 2003)
S83-043 Infrared Module — Circular
9
Item
1
2
3
4
5
6
7
8
9
*
Part No.
Description
Qty
S51-003
S83-041
160-197
247-001
142-002AV
140-718
S83-039
269-832
S04-112
124-067
Shell Assembly
PC Mounting Board
Screw 10-32 x 3/8" Lg.
Insulator
Washer
Sensor Bracket
IR Sensor Classic WFT
IR Curved Lens
Module Cover Assy.
Cover Gasket
1
1
12
3
12
6
6
6
1
1
3
4
2
5
6
7
NOTE: Item 4 - 247-001 Insulators go between
circuit board and metal mounting tabs.
*
Not shown on diagram
8
1
S83-040 Infrared Module — Semi-Circular
Item
1
2
3
4
5
6
7
8
9
*
Part No.
Description
S51-002
S83-038
160-197
247-001
142-002AV
140-718
S83-039
269-832
S04-112
124-067
Shell Assembly
PC Mounting Board
Screw 10-32 x 3/8" Lg.
Insulator
Washer
Sensor Bracket
IR Sensor Classic WFT
IR Curved Lens
Cover Assembly
Cover Gasket
NOTE: Item 4 - 247-001 Insulators go between
circuit board and metal mounting tabs.
*
Qty
1
1
8
3
8
3
3
3
1
1
9
5
4
6
7
3
2
Not shown on diagram
8
1
48
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Infrared AccuZone Valve Assembly — Circular & Semi (Terrazzo and
Stainless Steel Bowls; Bradstone Bowls Prior to September 2003)
To Sprayhead
2
13
3
1
5
7
6
9
3
From
Supply
8
4
10
12
From Supply
11
Parts List
Item
Part No.
1
2
2
3
4
5
6
7
8
9
10
11
12
13
S83-134
S83-043
S83-040
R68-600012
S08-055
269-851
S02-045
S60-003
129-007
110-005
124-001AF
S01-038
S01-525
269-626
Description
24 VAC Transformer (with Female Connectors)
Infrared Module — Circular (See previous Page)
Infrared Module — Semi-circular (See previous p age)
1/2" Tubing to Sprayhead
Solenoid Assy.
Reducer
Volume Control Valve
Stop-Strainer-Check Valve
Tailpiece
Tailpiece Nut
Tailpiece Washer
Manual Mixing Valve
TMA (Optional)
3/8" NPT x 1/2" Tube Conector
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Qty
1
1
1
1
2
1
1
2
2
2
2
1
1
1
49
Bradley Washfountains
Parts and Service Guide
Troubleshooting AccuZone Infrared
1. Check the lens — (windows) of the sensor(s) to make sure they are not pushed in, covered with debris or
scratched. Scratches can distort the view of the sensor. Clean if dirty or replace if damaged. If lens
needs to be replaced use Lord acrylic adhesive 406/19 or an epoxy glue to glue the lens in place and seal
from outside moisture. Clean off excess glue and allow to dry.
2. Verify there is power — to the transformer and verify there are 24 volts coming from the transformer.
3.Unplug the transformer — harness from the module harness, disconnect module harness from the solenoid valve. Plug the transformer directly to the solenoid valve. If there is 24 volts, and the solenoid is
working properly, water will turn on and run continuously. If the water does not turn on and you know
there are 24 volts coming from the transformer, the solenoid will have to be replaced.
4. If the water does not turn off or dribbles — after disconnecting the power, there is debris at the
diaphragm of the solenoid valve. Take apart the solenoid valve to check for debris which may be keeping
the valve open. Unscrew the 3 or 4 screws that hold the solenoid to the lower valve body. (The S27-250
solenoid valve does have a screen in the inlet end. Check and make sure that screen is clean.) Clean the
diaphragm and make sure the small hole in the diaphragm is not plugged. This small hole is very hard to
see. Hold it up to the light to find the hole. It is located about half way between the OD and the ID. Soak
the diaphragm in vinegar for 15 to 20 minutes and rinse well with water to remove mineral deposits.
Reassemble valve and test again with power from the transformer.
5. If the solenoid is working, — take the cover off the module and check to make sure all leads are connected properly and all sensors are plugged onto the circuit board.
6. Make sure the output and input wires — from the circuit board are not loose or broken off.
7. Check the MOV (metal oxide Varistor) — on the circuit board
for discoloration. This varistor can be burned out from power surges
Varistor
and lightening strikes. The discoloration will be evident if the
Output
varistor is burned out. If the varistor is burned out, the circuit
wires to
board will have to be replaced. Note: Do not use the part number
solenoid
printed on the circuit board, that is a bare board.
Input wires from transformer
8. Unplug all sensors — from the circuit board (remembering where
the wires go). Plug in one sensor at a time. If sensor works properly, continue on to the next sensor. Test all sensors individually. If some sensors work and some do not,
plug the sensors not working into the location where the sensors do work. This will confirm that the sensor
is dead or there is a problem in the circuit board. It is possible that an on site electrical surge or a lightening strike could burn out a sensor, all sensors or an individual circuit on the circuit board. If you find any
in this condition, add a good surge protection device to the circuit to avoid future problems. Note: Make
sure your sensor has the foam strip properly applied to the center of the sensor.
9. If an individual station is not working, — loosen the screws on the
Sensor with plug
sensor bracket and reposition to make sure the sensor is properly positioned in front of the lens (window). The sensor should not be seeing
S83-039
any edges of the module opening.
10.Replace sensors as necessary. — Order assembly # S83-039.
Foam Spacer
11.If a new installation, — and the above checks do not resolve the probSensor assembly includes the disconnect
lem, check the wiring of the sensor plugs.
terminal and foam spacer on face of sensor.
The bracket is not included as shown.
If you need further assistance, please call your local Bradley Representative.
Please call us at 1-800-Bradley if you need the name and telephone number of your local Bradley
Representative.
50
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Infrared Module — Adaptive Circular & Semi
(Terreon® Bowls; Bradstone Bowls from September 2003 to Present)
Parts List — Infrared Circular Module S50-344
Item
1
2
3
4
5
6
*15
**16
*17
*18
**19
**
*
**
Part No.
Description
219-035A
269-1351
P10-569
269-1878
269-1219
S04-112
S53-261
S53-271
S53-261A
S53-272
269-599
124-067
Circular Shell
Sensor Window
Velcro Strip
Adaptive Sensor
Clip
Module Cover
Wire, Red, 4", Female Leads
Wire, Black, 4", Female Leads
Wire, Red, 48", Female Leads
Wire, Black, 48"
Cable Tie
Cover Gasket
Qty
1
6
6
6
12
1
4
5
2
1
6
1
Illustrated on next page.
Not shown.
6
4
5
1
3
2
Sensor Eyes (part of sensor - Item 4)
to be inserted in window adjacent
to sensor.
Windows (Item 2) snap fit
into module shell (Item 1).
Put a small amount of RTV
sealant between window lip
and module shell to
seal out contaminants.
Parts List — Infrared Semi-Circular Module S50-367
Item
1
2
3
4
5
6
**15
**16
*17
*18
**19
**
*
**
Part No.
Description
219-033A
269-1351
P10-569
269-1878
269-1219
S04-112
S53-261
S53-271
S53-261A
S53-272
269-599
124-067
Circular Shell
Sensor Window
Velcro Strip
Adaptive Sensor
Clip
Module Cover
Wire, Red, 4", Female Leads
Wire, Black, 4", Female Leads
Wire, Red, 48", Female Leads
Wire, Black, 48"
Cable Tie
Cover Gasket
Illustrated two pages after this one.
Not shown.
Qty
1
3
3
3
6
1
2
2
1
1
3
1
6
4
5
1
3
2
Sensor Eyes (part of sensor - Item 4)
to be inserted in window adjacent
to sensor.
Windows (Item 2) snap fit
into module shell (Item 1).
Put a small amount of RTV
sealant between window lip
and module shell to
seal out contaminants.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
51
Bradley Washfountains
Parts and Service Guide
Infrared Adaptive Valve Assembly — Circular (Terreon Bowls;
Bradstone Bowls from September 2003 to Present)
* Infrared Module
2
18 * Black Wire
Leader
* Red Wire 17
To Sprayhead
Male Connector
Supply Tube 3
14
Female Connector
* Red Wire
17
5
3 Supply Tube
9
Supply Tube 3
4
1
3
6
1/2" Supply
8
7
* Wire
15
11 10
13 12
10 11
6
1/2" Supply
Parts List
*
Item
Part No.
1
*2
3
4
5
6
7
8
9
10
11
12
13
14
S83-134
S50-344
R68-600012
269-1222
269-764
S60-003
S08-055
269-620
S02-045
110-005
124-001AF
S01-038
S01-525
269-626
Description
Qty
24 VAC Transformer
Infrared Module
1/2" Tubing to Sprayhead
Tee
Tee Union
Check Valve
Solenoid Assy.
Adapter
Volume Control Valve
Tailpiece Nut
Tailpiece Washer
Manual Mixing Valve
TMA (Optional) - Manual Mixing Valve Shown
3/8" NPT x 1/2" Tube Conector
1
1
1
1
1
2
2
1
1
2
2
1
1
1
Parts list on previous page.
52
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Infrared Adaptive Valve Assembly — Semi-Circular (Terreon Bowls;
Bradstone Bowls from September 2003 to Present)
* Infrared Module
2
18 * Black
Wire Leader
To Sprayhead
17 * Red Wire
Male Connect.
11
Female Connect.
Supply Tube 3
5
Supply Tube 3
12
6
4
1
4
To 1/2" Supply
7
8
To 1/2" Supply
9
10
7
8
Parts List
*
Item
Part No.
1
*2
3
4
5
6
7
8
9
10
11
12
S83-134
S50-367
R68-600012
S60-003
S08-055
S02-045
110-005
124-001AF
S01-038
S01-525
269-626
269-851
Description
24 VAC Transformer
Infrared Module
1/2" Tubing to Sprayhead
Check Valve
Solenoid Assy.
Volume Control Valve
Tailpiece Nut
Tailpiece Washer
Manual Mixing Valve
TMA (Optional) - Manual Mixing Valve Shown
3/8" NPT x 1/2" Tube Connector
Reducing Coupling, 1/2 NPT x 3/8 NPT
Qty
1
1
1
2
1
1
2
2
1
1
1
1
Parts list — See two pages before this one.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
53
Bradley Washfountains
Parts and Service Guide
Troubleshooting Adaptive Infrared
There is a LED diagnostic light built into the small black box housing the circuitry for the sensor.
Below is a list of what the signals from the LED mean. Use this list to troubleshoot the sensor.
1. LED not illuminated — no power is getting to the sensor. Check for power at the 110 VAC wall
outlet and from the wires from the 24 VAC transformer. If there is 110 VAC power at the wall
outlet, but no power from the transformer, touching the leads from the transformer while plugged
in or a power surge may have burned out the transformer. Add surge protection at the outlet if a
power surge is suspected and replace the transformer. If 24 VAC power is being supplied from
the transformer, check for loose wires and proper connections (refer elecrtrical wiring diagrams
on previous two pages).
2. Fast Blink — Sensor is detecting something in its view and water should be on (power is being
sent to the solenoid). If the sensor is blinking fast, the water is turning on and there is nothing in
the detection area, disconnect the power for at least 30 seconds. This will allow the sensor to
loose it's memory and be reset. Reconnect the power and wait 2 full minutes to allow the sensor
to relearn the environment before attempting to activate. The sensor may take up to 8 minutes to
readjust if it activated during those 2 minutes. If the condition persists, make sure the LED's at
the ends of the sensor cables are pushed all the way in to the backs of the lenses. If the sensor is
blinking fast and the water is not turning on, go through the troubleshooting guide for the solenoid.
3. Slow Blink — Sensor is detecting something in its view and the water is off (power is not being
sent to the solenoid). The sensor has detected a stationary object in its view for more than 30
seconds and shut off power to the solenoid valve. Remove the object, if it is still in the bowl, and
repeat the part of Step 2 for resetting the sensor.
4. Blinking SOS (3 short, 3 long, 3 short) — The sensor has detected an overload condition and
shut down to protect it's circuits. Check connections against the wiring diagram. This condition
usually means the solenoid valve is not properly wired. After correcting any wiring error, it will
be necessary to restart the sensor by repeating the part of Step 2 for resetting the sensor.
If you need further assistance, please call your local Bradley Representative. Please call us at
1-800-Bradley if you need the name and telephone number of your local Bradley Representative.
54
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Touch Time™ Module — Circular & Semi
5
2
1
3
Circular
4
Parts List — Touch Time Circular Module S83-179
Item
1
2
3
4
5
**
**
Part No.
Description
219-031A
S83-139B
140-802
110-115
S04-113
124-067
Circular Shell
Touch Time Switch
Touch Time Bracket
1/2" - 14 NPSM Nut, Brass
Module Cover Assembly
Cover Gasket
Qty
1
2
2
2
1
1
Not shown.
5
3
1
2
Semi-Circular
4
Parts List — Touch Time Semi-Circular Module S83-180
Item
1
2
3
4
5
**
**
Part No.
Description
219-032A
S83-139B
140-802
110-115
S04-113
124-067
Circular Shell
Touch Time Switch
Touch Time Bracket
1/2" - 14 NPSM Nut, Brass
Module Cover Assembly
Cover Gasket
Qty
1
1
1
1
1
1
Not shown.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
55
Bradley Washfountains
Parts and Service Guide
Touch Time™ Valve Assembly — Circular & Semi
To Sprayhead
12
2
3
6
5
8
2
From Supply
7
4
9
11
From Supply
10
Parts List
*
**
56
Item
Part No.
*1
2
3
4
5
6
7
8
9
10
11
12
*13
**
S83-134
R68-600012
269-851
S08-055
S02-045
S60-003
129-007
110-005
124-001AF
S01-038
S01-525
269-626
269-1364
S83-142
Description
Qty
24 VAC Transformer
1/2" Tubing to Sprayhead
Reducing Coupling, 1/2 NPT x 3/8 NPT
Solenoid Assy.
Volume Control Valve
Check Valve
Tailpiece
Tailpiece Nut
Tailpiece Washer
Manual Mixing Valve
TMA (Optional)
3/8" NPT x 1/2" Tube Connector
Terminal Block
Power Cord Assembly
1
1
1
2
1
2
2
2
2
1
1
1
1
1
Illustrated on next two pages.
Not Illustrated.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Touch Time™ Wiring — Circular
**
*1
** Circular TT
Module Assembly
13
*
**
Parts list on previous page.
Parts list — See two pages before this one.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
57
Bradley Washfountains
Parts and Service Guide
Touch Time™ Wiring — Semi-Circular
** Semi-Circular TT
Module Assembly
**
*1
13
*
**
58
Parts list — See two pages before this one.
Parts list — See three pages before this one.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Parts and Service Guide
Bradley Washfountains
Touch Time Troubleshooting
IMPORTANT:
CAUTION:
Make sure there is electrical power going to the transformer and there are 24 volt s coming from the transformer.
Be sure to turn off electrical and water supplies as instructed during
troubleshooting.
If the Touch Time™ push button unit does not function properly
1. Make sure the water supply and the 24 V AC power are both turned on.
If the water supply and the electrical power are both turned on but the push button is still not functioning,
check the wiring following the steps outlined in procedure #2 below.
2. Check the wiring following the procedure outlined below:
a. Turn the electrical power off.
b. Check the wiring for loose connections or corrosion and correct if necessary .
c. Turn the electrical power back on and retest the push button.
If, after checking the wiring, the push button is still not functioning properly , test the transformer following
the steps outlined in procedure #3.
3. Test the transformer with a volt meter following the procedure outlined below:
a. Turn the water supply off (the electrical power should remain on).
b. Set the volt meter scale to be able to read “24 V AC”.
c. Connect the volt meter leads from the transformer as shown in the diagram.
d. The voltage reading should indicate 24 VAC ± 10%.
If you are unable to obtain a proper voltage reading, the transformer is not working properly and needs to
be replaced. Contact your Bradley representative to order a replacement transformer.
If the transformer is working properly, turn the water supply back on and test the solenoid following the
steps outlined in procedure #4.
4. Test the solenoid valve following the procedure outlined below:
a. Disconnect the Green/Gray wires from the solenoid.
b. Disconnect the brown transformer leads from the terminal block.
c. Connect the brown transformer leads directly to the solenoid. The solenoid coil should activate and
you should hear a single click and a humming noise.
d. If the solenoid still does not function, turn of f the electrical power. Then remove the four screws that
secure the clamping plate to the valve body. Be careful not to lose the armature or spring
e. Remove the diaphragm and clean it gently but thoroughly . Hold the diaphragm up to a light and find the
small hole which is located about halfway between the inner diameter and the outer diameter . Make
sure the hole in the diaphragm is not plugged.
f.
Reassemble the valve in reverse order and test again with power from the transformer .
If the solenoid coil does not activate, the solenoid valve is not working properly and needs to be replaced.
Contact your Bradley representative to order a replacement solenoid valve assembly .
If, after checking the transformer, the solenoid valve and the wiring, you are unable to activate the sprayhead by pressing the Touch Time push button, the Touch Time switch assembly is not working properly
and needs to be replaced. Contact your Bradley representative to order a replacement switch assembly.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
59
Bradley Washfountains
Parts and Service Guide
Common Parts — S27-250 Solenoid
SPRING
(269-578)
4
1
ARMATURE
(269-577)
INLET
SCREEN
DIAPHRAGM
(269-1346)
2
3
S08-055 Solenoid Valve Assembly
Item
1
2
3
4
60
Part No.
S27-250
269-1246
269-626
S65-155
Description
Solenoid Valve
3/4x 3/8 Reducing Coupling
Male Connector
Solenoid Repair Kit
Qty
1
1
1
1
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Common Parts — Solenoid (Prior to March 2002; Semi-Circular Only)
3
2
1
269-719 Eaton Solenoid Valve Assembly
Repair
Kit
S65-113
Item
Part No.
Description
Qty
1
2
3
269-983
269-577
269-578
Diaphragm
Armature
Spring
1
1
1
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
61
Bradley Washfountains
Parts and Service Guide
Solenoid Valve Troubleshooting
IMPORTANT: Make sure there is electrical power going to the transformer and there
are 24 volts coming from the transformer.
CAUTION: Turn off electrical and water supplies to unit before troubleshooting.
Problem:
Cause:
Solution:
Sprayhead drips or fails to shut off.
There is debris trapped between the diaphragm and the valve seat or a clogged
inlet screen. Refer to solenoid parts breakdown two pages previous to this one.
Remove debris between diaphragm and the valve seat. Clean the inlet screen.
1. Remove the four screws that secure the clamping plate to the valve body. Be careful not to lose
the armature or spring.
2. Remove the diaphragm and clean it gently but thoroughly. Hold the diaphragm up to a light and
find the small hole which is located about halfway between the inner diameter and the outer
diameter. Make sure the hole in the diaphragm is not plugged.
3. Reassemble the valve in reverse order and test with power from the transformer.
Problem:
Cause:
Solution:
Sprayhead fails to turn on.
A failed coil for the valve or improper wiring connection.
Test the valves and check the wiring connections.
1. Disconnect the wires from the IR module to the transformer and solenoid (refer to wiring diagrams for connections).
2. Connect the wire from the transformer to the solenoid valve. Both transformer wires should now
be connected to the solenoid valve which should turn on immediately and run continuously.
• If the solenoid valve does not turn on and you have made sure that there is 24-volt power coming from the transformer, you know that the solenoid has failed and will need to be replaced.
3. After replacing the solenoid valve (if necessary), reconnect the wire from the transformer to the
IR module. Test the solenoid valve again.
• If the solenoid valve does not turn on, check the wiring for proper connections. If it still fails to
turn on, the problem may be in the sensor. Refer to the instructions on Troubleshooting
Adaptive Infrared and follow the sensor troubleshooting procedure outlined there.
62
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Air Valve Module — Circular & Semi
2
8
9
7
11
5
10
12
3
Pushbutton
Wrench
Part # 130-023
4
Circular shown,
Semi-Circular has
only one pushbutton.
6
1
S65-132 Air Valve Module — Circular
S65-134 Air Valve Module — Semi-Circular
Circular
Item
1
1
2
3
4
5
6
*7
*8
*9
*10
*11
*12
13
*
Part No.
Description
219-017
219-018
S04-113
S08-324
140-743
160-165
110-115
119-227A
125-099
135-065
118-279
169-890
198-010
269-1186
Shell Assembly, (2 holes)
Shell Assembly, (1 hole)
Module Cover Assembly
Pushbutton Assembly
Actuator Bracket
Screw
Nut
Piston
U-Cup
Spring
Actuator Body
Straight Tube Connector
Duckbill Check
Adjustable “L” Fitting
Semi-Circular
Qty
1
—
1
2
2
4
2
2
2
2
2
2
2
2
—
1
1
1
1
2
1
1
1
1
1
1
1
1
Items 7-12 are available as an actuator assembly, order part number S65-168.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
63
Bradley Washfountains
Parts and Service Guide
Air Valve Assembly — Circular
8
2
6
1/2" SUPPLY TUBING
FROM SPRAYHEAD
7
1/8" O.D. TUBING
TO ACTUATOR
16
1
4
3
5
10
10
1/2" SUPPLY
1/2" SUPPLY
12
13
15
14
11
Parts List
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
64
Part No.
S07-044
R68-600012
169-059
113-006AL
S02-045
269-1140
198-008
169-890
S53-046
S60-003
129-007
110-005
124-001AF
S01-038
S01-525
269-626
Description
Air Valve
1/2" Tubing to Sprayhead
Reducer
3/8" Nipple
Volume Control Valve
Check Valve
Adapter
1/8" Tube Connector
1/8" O.D. Tee
Stop-Strainer-Check Valve
Tailpiece
Tailpiece Nut
Tailpiece Washer
Manual Mixing Valve
TMA (Optional)
3/8" NPT x 1/2" Tube Connector
Qty
1
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Bradley Washfountains
Parts and Service Guide
Air Valve Assembly — Semi-Circular
2
1/8" O.D. TUBING TO ACTUATOR
1/2" SUPPLY TUBING
FROM SPRAYHEAD
13
1
4
3
5
7
7
1/2" SUPPLY
1/2" SUPPLY
9
10
12
11
8
Parts List
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
Part No.
S07-044
R68-600012
169-059
113-006AL
S02-045
169-890
S60-003
129-007
110-005
124-001AF
S01-038
S01-525
269-626
Description
Air Valve
1/2" Tubing to Sprayhead
Reducer
3/8" Nipple
Volume Control Valve
1/8" Tube Connector
Stop-Strainer-Check Valve
Tailpiece
Tailpiece Nut
Tailpiece Washer
Manual Mixing Valve
TMA (Optional)
3/8" NPT x 1/2" Tube Connector
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Qty
1
1
1
1
1
1
2
2
2
2
1
1
1
65
Bradley Washfountains
Parts and Service Guide
Air Valve Tubing Connection
If the air valve is leaking.
1. Depress the release button per the Figure below.
2. Remove and trim the tubing for a fresh surface.
3. Reinsert the tubing until it seats on the tube stop.
RELEASE
BUTTON
1/8”
TUBING
LOCKING
SLOPE
SEALING
RING
GRIPPING
RIDGE
TUBE
STOP
Adjusting the Air Valve Metering Time
Note: The air valve timer is located next to the tube connector on the air valve body. The timer is capped
with a filter to prevent dirt build-up on the timer. The air valve timing can be adjusted from 5-45 seconds.
Refer to Figure below when adjusting the air valve.
1. Remove the filter cap. Use a screwdriver to tighten or loosen the timer. Turning the timer clockwise increases the time, turning the timer counterclockwise decreases the time.
2. Continue to adjust the timer until it is set at the desired length.
3. Replace the filter cap.
66
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
Parts and Service Guide
Bradley Washfountains
Air Valve Troubleshooting
Problem: Valve will not shut off.
Cause: Timing mechanism is clogged.
Solution: Clean and inspect timing mechanism:
1. If compressed air is available, blow water and debris from perforated metal sleeve of timing
mechanism.
2. Turn adjusting screw in all the way but do not force screw.
3. Turn adjusting screw out to desired cycle time.
Problem: Valve will not turn on.
Cause: Water is not being supplied to unit.
Solution: Open all stops on mixing valve.
Problem: Timing can not be adjusted for more than 5 seconds.
Cause: There is an air leak
Solution: Check the valve assembly:
1. Check all tubing and fittings for proper assembly.
2. Tighten all screws which hold valve together.
Problem: Push button does not work properly.
Cause: Air volume may not be sufficient to operate valve.
Solution: Check for leaks and lubricate U-cup:
1. Check all fittings for air leaks.
2. Disassemble pushbutton and lubricate U-cup seal.
Problem: Water is dripping from the aerator.
Cause: Debris has accumulated on valve seat or orifices.
Solution: Clean and inspect valve seat.
1. Remove screws and disassemble metering valve.
2. Clean valve seat and inspect for deep gouges or scratches. Replace if necessary.
3. Remove all debris that may be clogging center hole of plastic diaphragm assembly.
4. Remove any debris clogging off-center hole in rubber diaphragm.
Bradley Corporation • 215-1370 Rev. N; EN 12-00-014
67
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement