Dishwasher DBI664 XXLSSOF OPERATING INSTRUCTIONS

Dishwasher DBI664 XXLSSOF OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Dishwasher DBI664 XXLSSOF
Contents
Display panel
Important safety instructions
Before washing for the first time
Loading the dishwasher
Using the dishwasher
Settings
2
3
4
6
9
13
Care and maintenance instructions
Troubleshooting
Technical information
Service
Notes
Quick start guide
15
17
20
21
22
24
Dear Customer,
Thank you for choosing this quality product from ASKO.
We hope it will meet your expectations and fulfill your needs for many years to come. Scandinavian design combines clean
lines, everyday functionality, and high quality. These are key characteristics of all our products and the reason they are
greatly appreciated throughout the world.
To get the most out of your new dishwasher, we recommend that you read the operating instructions before using it. The last
page also includes a Quick start guide.
Display panel
To switch on the dishwasher, press and hold the main power switch until the display lights up.
"Welcome to your new ASKO. This is a first time set up." is shown on the display the first time the dishwasher is switched on. It
is important that you choose the right settings to ensure good dishwashing results. See page 4.
Main power switch
Display
Start/Stop
START
Eco
STOP
2:00
Speed mode
Program mode selector
Navigation buttons for selecting a program
2
Option Delayed Start
Option Extra Dry
Important safety
instructions
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING!
When using your dishwasher, follow basic precautions, including the
following:
• Read all instructions before using the dishwasher.
• Use the dishwasher only for its intended function.
• Use only detergents or wetting agents recommended for use in
a dishwasher and keep them out of the reach of children.
• When loading items to be washed:
– locate sharp items so that they are not likely to damage the door
seal, and
•
•
•
•
•
•
•
•
– load sharp knives with the handles up to reduce the risk of
cut-type injuries.
Do not wash plastic items unless they are marked “dishwasher
safe” or the equivalent. For plastic items not so marked, check
the manufacturer’s recommendations.
Do not operate the dishwasher unless all enclosure panels are
properly in place.
Do not tamper with controls.
Do not abuse, sit on, or stand on the door or dish rack of the
dishwasher.
To reduce the risk of injury, do not allow children to play in or on
a dishwasher.
Under certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for two weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not
been used for two weeks, before using the dishwasher turn on all
hot water faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen gas. As the
gas is flammable, do not smoke or use an open flame during this
time.
Remove the door to the washing compartment when removing
an old dishwasher from service or discarding it.
Read the grounding instructions in the installation instructions.
General
• Do not run the dishwasher while you are out of the home.
• Do not store or use combustible materials, gasoline, or other
flammable vapors and liquids in the vicinity of this or any other
appliance.
• Disconnect electrical power to dishwasher before servicing.
• Repairs should be done by a qualified technician.
• Should a child swallow dishwasher detergent or rinse aid, give
plenty to drink immediately, i.e., one or two glasses of milk or water.
Do not try to induce vomiting. Seek medical advice immediately:
Call the National Capital Poison Center at 1-800-222-1222.
• Always close the door and start the dishwasher as soon as you put
in the detergent.
• Always keep small children away from the machine when it is open.
There may be some detergent residue left inside the machine.
• If dishwasher detergent gets in someone’s eyes, rinse them with
plenty of water for at least 15 minutes.
Activate child lock (Kid Safe™)
You can activate the child lock (button lock) to prevent children from
starting the dishwasher. See the chapter Settings.
Winter storage/Transport
• Store the dishwasher where the temperature remains above freezing.
• Avoid long transport distances in very cold weather.
• Transport the dishwasher upright or laying on its back.
Overflow guard function
The overflow protection starts pumping out the machine and turns off
the water supply if the water level in the dishwasher exceeds the normal
level. If the overflow protection is triggered, turn off the water supply
and call the Customer Care Center.
Packing material
The packaging protects the product during transport. The packaging
material is recyclable. Separate the different packaging materials to
help reduce raw material use and waste. Your dealer can take the
packaging for recycling or direct you to the nearest recycling center.
The packaging is comprised of:
•
•
•
•
Corrugated cardboard made from up to 100% recycled material.
Expanded polystyrene (EPS) with no added chlorine or fluorine.
Supports made from untreated wood.
Protective plastic made from polyethylene (PE).
Disposal
• When the machine has reached the end of its service life and is to
be disposed of, it should immediately be made unusable. Pull out
the power cable and cut it as short as possible.
• The dishwasher is manufactured and labeled for recycling.
• Contact your municipality for information about where and how your
dishwasher can be recycled correctly.
WARNING!
This product may contain chemicals known to the state of California
to cause cancer or reproductive harm.
Installation
See the separate installation instructions.
Child safety
TIP!
Dishwasher detergents and rinse aids are corrosive, so always keep
them out of reach of children.
3
Before washing for the
first time
1. Checking water hardness
2. Basic settings
In order to achieve good dishwashing results, the dishwasher needs
soft water (water with low mineral content). Hard water leaves a white
coating on dishes and the dishwasher.
To switch on the dishwasher, press and hold the main power switch
until the display lights up.
Water hardness is specified using the following scales: The German
water hardness scale (°dH) and the French water hardness scale (°fH).
A water supply with a water hardness in excess of 6°dH (9°fH) must
be softened. This is done automatically with the aid of the built-in water
softener. In order for the softener to function optimally, it must be
adjusted to the hardness of the water supply.
"Welcome to your new ASKO. This is a first time set up." is shown
on the display. It is important that you choose the right settings to
ensure good dishwashing results.
Select setting
Contact the local water utility, or measure the water hardness using
the supplied test strip, to check the water hardness in your area. Once
you have adjusted the water softener, use detergent and rinse aid
doses suitable for soft water.
How to use the test strip:
1 Turn on the water faucet and let the water run for a minute or so.
Main power switch
Confirm setting
2 Fill a glass with water.
3 Remove the test strip from its packaging.
Settings
4 Dip the test strip in the water for about one second.
5 Wait one minute. Now compare the colors of the squares with the
water hardness table.
Test strip
°dH °fH
4 green
<3
<5
1 red
>4
>7
2 red
>8
>15
3 red
>14 >25
4 red
>21 >38
1
Language
Select the language to be shown on the display.
2
Rinse aid 0/1/2/3/4/5/TAB
Use rinse aid to improve wash and dry times. Also use rinse aid to
achieve clear and spotless results.
Select rinse aid dosage. The rinse aid dispenser can be adjusted
between 0 (Off) and 5 (High dosage).
When using an all-in-one detergent that contains rinse aid, select the
TAB setting. Read more about all-in-one detergent in the chapter
Using the dishwasher.
Pre-selected at factory: 5
3
Water hardness 0/1/2/3/4/5/6/7/8/9
Choose a setting depending on the hardness of the water supply.
See the water hardness table below. It is important that this setting
is correct!
°dH
°fH
°dH
°fH
0-5
0-9
20-24
35-43
6-8
10-14
25-29
44-52
9-11
15-20
30-39
53-70
12-14
21-25
40-49
71-88
15-19
26-34
50+
89+
Do not forget to put salt in the salt compartment after you have set
the water softener to 1 - 9.
For a water supply with a hardness under 6°dH (9°fH), select 0. The
water softener is deactivated and no salt is needed.
Pre-selected at factory: 4
To change the chosen setting, see the chapter Settings.
4
3. Top up with rinse aid
4. Fill up with salt
Use rinse aid to improve wash and dry times. Also use rinse aid to
achieve clear and spotless results.
Before you begin using a dishwasher with a water softener, you must
fill the salt compartment with salt for the water supply to be softened
automatically. Use large grain salt or special dishwasher salt.
Press to open
WARNING!
In order to avoid rust stains, a dishwashing program must be started
immediately after adding salt.
Never pour dishwasher detergent into the salt compartment. This
destroys the water softener!
Do as follows the first time:
1 Unscrew the lid as illustrated.
1 Open the rinse aid compartment lid.
2 Carefully top up with rinse aid. Only add rinse aid to the level marked
max.
2 Insert the funnel supplied with the dishwasher in the salt
compartment top-up hole. First, pour in about 0.3 gal (1 l) of water.
3 Wipe up any spilled rinse aid around the compartment.
3 Then add salt, a maximum of 2 lb (1.0 kg), until the compartment
is full.
4 Close the lid firmly.
4 Wipe up any excess salt so that the lid can be screwed on firmly.
5 Run a program to ensure that any salt in the dishwasher is rinsed
away.
Add rinse aid
When the rinse aid needs topping up, the above symbol lights on the
display.
After topping up, it may take a while before the symbol goes out.
NOTE!
Increase the rinse aid dosage:
• If the dishes have water marks.
Reduce the rinse aid dosage:
• If the dishes have a sticky white/blue film.
• If the dishes are streaked.
• Heavy foaming. If you have very soft water, the rinse aid can be
diluted 50:50 with water.
Salt compartment lid
Add salt
When the salt needs topping up, the above symbol lights on the display.
When the salt runs out, unscrew the cap and fill the container with salt.
Water is only needed the first time! Wipe clean and tighten. Run a
program to ensure that any salt in the dishwasher is rinsed away.
After topping up, it may take a while before the symbol goes out.
5
Loading the dishwasher
Energy-efficient dishwashing
Fragile dishes
Run programs only with a full load
Wait until the dishwasher is fully loaded before running a program, this
way you save energy. Use the Rinse and hold program to rinse the
dishes if there are any unpleasant odors while you wait for the
dishwasher to become fully loaded.
Some cookware is not dishwasher safe. This can be for several reasons.
Some materials cannot withstand high temperatures, others can be
damaged by dishwasher detergent.
Run programs at a lower temperature
If the dishes are only lightly soiled, you can select a program with a
low temperature.
Select Green mode
The dishwasher has different program modes. To save energy and
water, use Green mode.
Use caution with, for example, handmade items, fragile decoration,
crystal/glassware, silver, copper, tin, aluminum, wood, and plastic.
Look for the "Dishwasher safe" marking.
Fragile decoration
Porcelain with decoration on top of the glazing (the items feel rough)
should not be washed in a dishwasher.
Better drying results are achieved if you open the door a little once the
program has ended. (If the dishwasher is built-in, the surrounding
furnishings must be resistant to any condensation from the dishwasher.)
Crystal/Glass
Wash fragile items made of crystal/glass, such as crystal glass from
Orrefors, using the gentle dishwashing program Crystal glass.
Remember to use a small amount of detergent and to place items so
that they do not touch each other during the wash.
Do not rinse under running water
Simply scrape off large food particles before loading the dishwasher.
Use rinse aid to improve wash and dry times. Also use rinse aid to
achieve clear and spotless results.
Choose a green detergent
Read the environmental declaration on the packaging!
Hand-painted glassware, as well as antique and very fragile items,
should not be washed in a dishwasher.
Connect to cold water
Connect the dishwasher to the cold water supply if the building is
heated using oil, electricity, or gas.
Connection to hot water supply
Connect the dishwasher to the hot water supply (max. 160 °F (70 °C))
if the building is heated using an energy-efficient means such as district
heating, solar power, or geothermal power. Choosing a hot water
connection cuts dishwashing times and reduces the dishwasher's
energy consumption.
NOTE!
Do not exceed the permitted water supply temperature. Certain
materials used in some cookware cannot withstand strong heat.
Silver
Silver and stainless steel items should not come into contact, as the
silver can become discolored.
Aluminum
Aluminum can lose its shine if washed in a dishwasher. However, good
quality aluminum pans can be washed in a dishwasher, even if some
of the shine will be lost.
Cutlery with glued handles
Some types of glue are not dishwasher safe. In such cases, the handles
may loosen.
Points to consider
• All dirty surfaces should face in and down!
• Dishes should not be placed in or on each other.
• Angle dishes with hollows, such as cups, so that the rinse water
will run off. This is also important for plastic items.
• Place the upper basket in its highest position when dishwashing
very large plates.
• Make sure small items cannot fall through the dishwasher basket;
place them in the top cutlery tray.
NOTE!
Check that the spray arms can rotate freely.
6
The baskets
The dishwasher includes a top cutlery tray, an upper basket, and a
lower basket with a cutlery basket.
The basket appearance may differ depending on the configuration.
Top cutlery tray
The top cutlery tray accommodates cutlery, ladles, whisks, and other
utensils.
Raising the upper basket
1 Pull out the upper basket.
2 Grab the sides of the upper basket with both hands and lift it up.
Lowering the upper basket
1 Pull out the upper basket.
2 While holding the basket, pull out the two locking handles on either
side to lower the upper basket.
Raising the top cutlery tray
1 Remove the top cutlery tray.
2 Pull the two locking handles forward on each side to raise the top
cutlery tray.
Lowering the top cutlery tray
1 Make sure the upper basket is in the lowest position.
2 Remove the top cutlery tray.
3 Slide the two locking handles down and back to lower the top cutlery
tray.
Lower basket
Place plates, side plates, serving dishes, pots, and cutlery (in the
cutlery basket) in the lower basket.
Place pots and pans in the right rear of the lower basket for the best
cleaning results from the two rear spray nozzles (WideSpray™), which
are intended for these types of dishes.
Upper basket
Place glasses, cups, bowls, side plates, and saucers in the upper
basket. Place all soiled surfaces down! Place wine glasses on the wine
shelf. Place knives on the knife stand, if applicable.
Foldable tines
Lower the foldable tines when washing large pots. Release the foldable
tines by pressing the catch inward before adjusting their position.
7
Typical load for 10 place settings
Upper basket with 10 place settings AHAM DW-1
Washing large plates
Move adjustable tines and their mounts to widen the distance between
the tine rows to adapt the lower basket to plates with a diameter greater
than 9 3/4" (25 cm).
Cutlery basket
Place cutlery with the handles facing down, except for knives, and
spread them out as much as possible. Ensure that spoons do not stack
inside each other.
The cutlery basket is best placed in the middle at the front of the lower
basket to best utilize dishwashing performance from the unique spray
nozzle (Power Zone Cutlery™), which is intended for the cutlery basket.
NOTE!
Ensure the upper basket is set to its lowest position.
WARNING!
Knives and other pointed items must be placed with the points down
in the cutlery basket or horizontally in other baskets.
Fold-down section for small items
The cutlery basket has a fold-down section in the middle for small
items, or small shafts, such as electric whisk attachments.
Accessory
Buy an extra cutlery basket. The extra cutlery basket is flexible and
can be dismantled and attached to the lower basket or the large cutlery
basket to make an extra large cutlery basket. This accessory is
available where you bought the dishwasher.
2
1
8
Lower basket with 10 place settings AHAM DW-1
Using the dishwasher
Add detergent
Press to open
NOTE!
Use only dishwasher detergent! Liquid hand-washing detergent must
not be used as the foam that forms prevents the dishwasher from
operating effectively.
Dishwasher tablets
Halve the tablet if it is difficult to close the dispenser lid. There is a risk
that the detergent will not be released properly if the lid is tight and
cannot open correctly.
NOTE!
1 Prewash detergent compartment
2 Main wash detergent compartment
Detergent is added according to water hardness.
Follow the instructions on the detergent packaging. This dishwasher
is fitted with a water softener, so use detergent and rinse aid doses
suitable for soft water.
Too much detergent can result in less effective dishwashing and also
entails greater environmental impact.
The detergent compartment must be dry when adding detergent. There
is one compartment for the prewash and one for the main wash. If
powder or liquid dishwasher detergent is used, add a small amount
of the detergent to the prewash compartment. Contact the detergent
manufacturer if you have questions about the detergent.
Dishwasher tablets are not recommended for short programs (less
than 75 minutes). Use powder or liquid dishwasher detergent instead.
All-in-one detergent
There are many types of all-in-one detergents on the market. Read
through the directions for these products carefully.
When using an all-in-one detergent that contains rinse aid, select the
TAB setting. Note that the salt compartment must be filled with salt.
NOTE!
Optimal washing and drying results are achieved by using normal
detergent together with separately dispensed rinse aid and salt.
9
Press and hold the main power switch until the display lights up.
Starting the dishwasher
START
Eco
STOP
2:00
Speed mode
Select the program
Select a program mode
The main power switch
Press and hold the main power switch until the display turns on. Also
check that the water supply valve is on.
Select a program
To select a program, press the Navigation button or until the desired
program is shown on the display.
Choose a program to suit the type of dishes and how dirty they are.
Normal wash
This program is recommended for daily, regular, or typical use to
completely wash a full load of normally soiled dishes, such as plates,
serving dishes, cups, and glasses. No options are recommended.
ECO wash
This program is most effective in terms of combined energy and water
consumption.
Sanitation wash
An effective program for daily use with slightly dried leftovers. (This
program is not intended for burnt food, such as on oven dishes.)
Time program
The program adapts to the specified running time or finish time. With
this program, it is important to choose a time suited to how dirty the
dishes are.
10
0:15-0:45
Lightly soiled dishes
1:00-1:30
Normally soiled dishes
2:00-2:30
Heavily soiled dishes
Select any options
been used without dried leftovers can also be washed using this
program.
Self-cleaning
Self-cleaning program for sanitizing the dishwasher tub, spray arms,
and spray pipes.
This program can be run (with no dishes in the machine) using regular
dishwasher detergent or citric acid. Special dishwasher cleaners are
also available in stores. For the removal of limescale deposits, see The
dishwasher tub in the chapter Care and maintenance instructions.
Upper half
You can use this program if you only have cups and glasses that need
washing in the upper basket. Lightly soiled dishes can also be placed
in the lower basket.
Lower half
You can use this program when you only want to wash plates and
cutlery in the lower basket. Lightly soiled dishes can also be placed
in the upper basket.
Select a program mode
To select a program mode, press the program mode selector until the
desired mode is shown on the display. The available program modes
vary between programs.
For a brief description, press and hold the program mode selector.
Green mode
The dishwasher uses less energy and water. The program time is
extended.
Speed mode
The program time is shortened, but the dishwasher uses more energy
and water.
– To set the desired program time, press and hold the option
button to set the desired program length.
Night mode
Lower noise level during the dishwashing program. The program time
is extended.
Rinse and hold
Use to rinse dishes while you wait for the dishwasher to become fully
loaded.
Intensive mode (Heat Boost)
Improves the dishwashing results, but the dishwasher uses more energy
and water. The program time is extended.
Plastic wash
A program intended for washing plastic items that are dishwasher safe.
This program has an extra long drying cycle. Porcelain and glasses
can also be washed.
Select an Option
Hygiene wash
This program is recommended for baby bottles and cutting boards
when additional sanitation is required. The temperature is high in the
main and final rinse.
Extra Dry
A higher temperature in the final rinse and a longer drying cycle
improve the drying results if you activate this option. Energy
consumption is slightly increased.
Crystal glass
A gentle dishwashing program with a low temperature for washing
fragile items made of crystal/glass, such as crystal glass from Orrefors.
Remember to use a small amount of detergent and to place items so
that they do not touch each other during the wash. See also Fragile
dishes in the chapter Loading the dishwasher. Porcelain that has just
For a brief description, press and hold the button for Extra Dry.
To select an option, press the option button until the desired option is
shown on the display. The available options vary between programs.
Delayed Start
When you select Delayed Start, the dishwasher will start 1-24 hours
after you have pressed the button Start/Stop and closed the door.
1 Press the button once to activate Delayed Start. Press the button
several times – or hold it in – to set the desired number of hours.
2 Press Start/Stop and close the door. The timer counts down and
the dishwasher starts after the selected delay.
If you want to cancel the Delayed Start option, open the door and press
and hold the main power switch until the display turns off.
TIP!
Activate the setting High temperature to improve the dishwashing
results. Energy consumption is slightly increased.
START
STOP
Starting the dishwasher
Press and hold Start/Stop until the display shows "Program started,
close door in 4 sec". This indicates that the dishwasher is ready to
start. Close the door properly within four seconds, otherwise the
dishwasher will not start.
If the dishwasher is turned off due to a
power failure
If the program was not finished, the interrupted program resumes when
power is restored.
NOTE!
During drying, the program is interrupted if the power is cut or the
door is open for more than 2 minutes.
Once the program has finished
Once the program has finished and the door is opened, "Ready"
appears on the display.
At the end of the program, one short signal will sound. Chapter Settings
describes how to change this function.
If the dishwasher is not started or the door is not closed within 2 minutes
of the last button press, the machine switches off.
Moreover, the end of the program is indicated by the status light turning
green.
Time remaining
The dishwasher switches off automatically after the program ends.
Once you have chosen a program, program mode, and options, the
time the program took when last used is displayed.
Status light™
To minimize the risk of leaks, we recommend that you turn off the water
supply valve if away from home for an extended period of time.
How to get the best drying results
• Fully load the dishwasher.
• Angle dishes with hollows, such as cups, so that the rinse water
will run off. This is also important for plastic items.
• Top up with rinse aid or increase the rinse aid dosage level.
• Activate the Extra Dry option.
• Open the door a little once the program has finished.
• Allow the dishes to cool before unloading the dishwasher.
Unloading the dishwasher
Status light
The status light at the bottom on the dishwasher provides information
by means of 3 different colors.
Hot porcelain is more fragile. Leave the dishes to cool in the dishwasher
before unloading them.
Unload the lower basket first to avoid any water drops from the upper
basket falling onto the dishes in the lower basket.
Blue - Do not load
The program has started.
Red - Do not load
The detergent compartment lid has been opened to add detergent.
Flashing red indicates a problem. See also the chapter Troubleshooting.
Green - Unload
The dishwashing program is finished. Standby light for 60 minutes.
Stopping or changing a program
If you want to change the program after starting the dishwasher, open
the door then press and hold Start/Stop for three seconds. Add more
detergent if the lid of the detergent dispenser has opened. Then choose
a new program, press Start/Stop, and close the door within four
seconds.
WARNING!
The dishwasher door must not be open while a program is in progress
according to UL Standards. If the door is opened, "Program paused"
is shown on the display. If you want the dishwashing program to
continue, press Start/Stop and close the door immediately. If you
want to cancel the dishwashing program, press and hold the main
power switch until the display turns off.
11
25
25
25
25
Normal wash 4)
ECO wash
Sanitation wash
Time program
2
2
60 °C
140 °F
60 °C
140 °F
60 °C
140 °F
60 °C
140 °F
50 °C
120 °F
2:20
2:20
1:50
1:30
1.0
1.0
0.8
1.4
1.1
1:50
1:50
1:20
1:00
2:25
0:07
0.6
0.6
0.5
0.9
0.6
0.01
0.4-1.2
0.6
3.2
3.2
2.4
2.6
3.2
0.8
2.9- 5.0
4.0
3.7
3.2
The energy label performance figures are based on this program. This program is recommended for daily, regular, or typical use to completely wash a full load of normally soiled dishes,
such as plates, serving dishes, cups and glasses. No options are recommended.
2
45 °C
115 °F
70 °C
160 °F
2:55
0.01
0:15-2:30
1:35
0.6
0.5
Energy
(approx. kWh)
Connection to hot water, approx. 120 °F (50 °C).
2
70 °C
160 °F
68 °C
155 °F
0:07
--- °C
--- °F
0.5-1.6
1.2
2:05
2:10
Dishwashing
time
(approx.
hrs:min)
Water cons.
(gallon)
4)
1
2
50 °C
120 °F
0:15-2:30
2:05
<65 °C
<150 °F
0.9
1.0
Energy
(approx. kWh)
Hot water 3)
1)
Connection to cold water, approx. 50 °F (10 °C). (A cold water supply is recommended.)
20
Lower half
1
2-3
<65 °C
<150 °F
65 °C
150 °F
2:30
2:30
Dishwashing
time
(approx.
hrs:min)
Cold water 2)
Consumption values
3)
20
Upper half
2
60 °C
140 °F
50 °C
120 °F
55 °C
131 °F
Final rinse
Consumption values vary depending on the temperature of the incoming water, room temperature, load size, selected additional functions, and more.
20
Crystal glass
2
55 °C
130 °F
1
2
Number of
rinses
53 °C
127 °F
Main wash
2)
25
Hygiene wash
1
0-2
2
2
2
Prewashes
1)
25
Plastic wash
Rinse and hold
Detergent,
compartment 2
(ml)
Program
Program chart
12
Settings
Open the dishwasher's Settings menu
To open the dishwasher's Settings menu, press the Navigation button
with the mode selector
.
or
until Settings menu is shown on the display and confirm your selection
To exit the dishwasher's Settings menu, select Exit and confirm your selection with the mode selector
.
Navigation buttons for choosing setting
Mode selector to confirm current setting
START
1� Language
Settings
English
STOP
Current setting
Settings
Options
1.
Language
English GB/English AU/English US/
You can choose the language used for the display.
Svenska/Dansk/Norsk/Suomi/Deutsch
/Italiano/Nederlands/Français/Español
2.
Select programs
Normal wash On/Off
ECO wash On/Off
Sanitation wash On/Off
Time program On/Off
Rinse and hold On/Off
Plastic wash On/Off
Hygiene wash On/Off
Crystal glass On/Off
Self-cleaning On/Off
Lower half On/Off
Upper half On/Off
Programs can be shown or hidden in the menu. Choose between
On and Off.
3.
Child lock
On/Off
You can activate the child lock (button lock) to prevent children
from starting the dishwasher.
To temporarily deactivate and activate the child lock, press
and hold the left Navigation button and the option button Delayed
Start for 3 seconds.
4.
Display settings
Contrast top display1/2/3/4
For adjusting the contrast of the display.
Logo in top display On/Off
Setting to hide the logo shown on the display.
5.
Feedback sound
0/1/2/3
This sound is used to confirm each button press.
6.
Buzzer volume
0/1/2/3
The buzzer indicates when a dishwashing program has ended.
Error messages are always indicated by a loud buzzer.
7.
Rinse aid
0/1/2/3/4/5/TAB
Setting for rinse aid dosage. The rinse aid dispenser can be
adjusted between 0 (Off) and 5 (High dosage).
Increase the rinse aid dosage:
• If the dishes have water marks.
Reduce the rinse aid dosage:
• If the dishes have a sticky white/blue film.
• If the dishes are streaked.
• Heavy foaming. If you have very soft water, the rinse aid can
be diluted 50:50 with water.
When using an all-in-one detergent that contains rinse aid, select
the TAB setting.
13
Settings
Options
8.
On/Off
Super rinse
Super rinse adds two extra rinses.
Activated in the following programs:
Normal wash
ECO wash
Sanitation wash
Plastic wash
Lower half
Upper half
9.
High temperature
On/Off
Activate the setting High temperature to improve the dishwashing
results. Energy consumption is slightly increased.
Activated in the following programs:
Normal wash
ECO wash
Sanitation wash
Plastic wash
Lower half
Upper half
10. Water hardness
0/1/2/3/4/5/6/7/8/9
Adjusting the water softener. Read off the appropriate setting from
the water hardness table below.
°dH
°fH
°dH
°fH
0-5
0-9
20-24
35-43
6-8
10-14
25-29
44-52
9-11
15-20
30-39
53-70
12-14
21-25
40-49
71-88
15-19
26-34
50+
89+
Do not forget to put salt in the salt compartment after you have set
the water softener to 1 - 9.
For a water supply with a hardness under 6°dH (9°fH), select 0.
The water softener is deactivated and no salt is needed.
14
Care and maintenance
instructions
Coarse filter
The coarse filter traps larger food particles, which cannot get past the
drain pump. Empty the coarse filter as necessary.
Top spray arm
• The upper basket must be removed before the top spray arm can
be released. Extend the upper basket then rotate the basket catch
on each runner outward (see illustration). Remove the basket.
Coarse filter
• Remove the top cutlery tray. Push the top spray arm up and turn
the spray arm bearings counterclockwise to remove the spray arm.
1 Lift the coarse filter by the handle.
2 Empty the coarse filter. Remember to replace it!
Upper spray arm
1 Pull out the upper basket.
Fine filter
Debris that collects on the fine filter is automatically rinsed away during
each wash. Clean the fine filter when necessary.
2 Unscrew the spray arm bearings counterclockwise to remove the
spray arm from the upper basket.
Fine filter
1 Turn the handle counterclockwise.
2 Lift the filter straight up using the handle. Remove the coarse filter
to clean the fine filter.
Lower spray arm
• Pull the lower spray arm straight up to release it.
3 Replace in reverse order. Check that the edges seal properly when
replacing the fine filter.
4 Lock the filter in place by turning the handle clockwise to the stop
position. The handle should point straight out from the dishwasher.
NOTE!
The dishwasher must not be used without the filters in place!
Dishwashing results may be affected if the coarse filter is incorrectly
fitted.
The door and the door seal
Spray arms
Regularly clean the sides of the door and the door seal. Use a slightly
damp cloth (with a little cleaner if necessary).
Holes and bearings can become blocked. Remove debris using a
needle or similar item. The spray arms have holes on the bottom.
Display panel
Keep the buttons clean and free from grease. Wipe them clean with a
dry or slightly damp cloth. Never use cleaners – they can scratch the
surface. Use the main power switch to turn off the dishwasher before
cleaning the buttons to avoid activating any buttons unintentionally.
The dishwasher tub
The dishwasher tub is made of stainless steel and is kept clean through
normal use.
Spray arms can be removed for cleaning. Remember to fit them firmly
back into place afterward.
Limescale deposits
If you have hard water, limescale deposits may build up in the
dishwasher. If this happens, run the Self-cleaning program with two
tablespoons of citric acid in the detergent compartment (with no dishes
in the machine). Special dishwasher cleaners are also available in
stores.
Never use anti-freeze, Draino®, CLR®, or other chemical cleaners.
15
Unblocking the drain pump
If the dishwasher still contains water after the program has finished,
something may be blocking the drain pump. Such items are easily
removed.
• Shut off the water.
• Unplug the unit from the power outlet.
• Call the Customer Care Center.
1 Turn off the machine using the main power switch and unplug it
from the power outlet.
2 Remove the coarse filter and the fine filter.
3 Scoop out the water from the dishwasher tub.
4 In order to inspect the drain pump, remove the colored stop on the
right in the bottom drain.
Drain pump stop
5 Turn the pump wheel located behind the drain pump stop by hand.
Carefully remove any items.
6 Replace the drain pump stop along with the fine and coarse filters.
7 Plug the machine in again.
If the dishwasher still does not start and a whirring sound is heard,
the overflow protection has been triggered.
16
NOTE!
Do not forget to replace the drain pump stop.
Troubleshooting
Type of fault on the display
Action
F10
Overfilling water 1
Clear the drain pump. See the section Care and maintenance instructions. If the problem persists,
call the Customer Care Center.
F11
Water outlet fault
See “Water remains in the dishwasher above the filters” in the table “Problem” below. If the problem
persists, call the Customer Care Center.
F12
Water inlet fault
Check that the water supply valve is on. If the problem persists, call the Customer Care Center.
The water pressure should be 4.2-140 psi.
F40
Inlet valve leakage
Turn off the water supply valve and call the Customer Care Center.
F52
Water level fault
Call the Customer Care Center.
F54
Overfilling water 2
Turn off the water supply valve and call the Customer Care Center.
F56
Circ. pump fault
Call the Customer Care Center.
Press any button to clear the error message.
Problem
Possible causes
Action
The buttons do not react when pressed.
You have pressed the buttons too soon after
opening the door.
Wait a moment then try again.
Child lock (button lock) activated.
See the chapter Settings.
The door is closed.
Open the door. The buttons only react to use
when the door is open.
The buttons are dirty.
Clean with a dry or slightly damp cloth.
The baskets are not correctly positioned.
Check that the baskets are correctly positioned
horizontally.
Cannot close door.
Check that the dishes are not blocking the
baskets from sliding properly into place.
The dishwasher does not start.
The Start/Stop start button has been pressed for Press and hold Start/Stop until the display shows
too short a time.
"Program started, close door in 4 sec".
The door is not closed properly or was not closed Close the door within four seconds, otherwise
immediately after pressing the Start/Stop button. the dishwasher will not start.
A fuse/circuit breaker has been tripped.
Check.
The plug is not plugged into the power outlet.
Check.
The water supply valve is turned off.
Check.
Overflow/leaks.
Check.
A whirring sound (the drain pump) is heard from Turn off the water supply valve. Pull out the plug
the dishwasher and does not stop when the main and call the Customer Care Center.
power switch is turned off.
Check that the Delayed Start option has not been Press and hold Start/Stop for three seconds if
selected.
you want to cancel the Delayed Start option.
17
Problem
Possible causes
Action
The dishes are not clean.
The spray arms do not rotate.
Check that the dishes are not blocking the spray
arms.
Spray arm holes or bearings blocked.
Clean the spray arms. See the chapter Care and
maintenance instructions.
Unsuitable dishwashing program.
Choose a longer program.
Incorrect detergent dosage.
Dose according to water hardness. Far too much
or far too little detergent can result in poor
dishwashing results.
Detergent is too old. Detergent is a perishable
product.
Avoid large packages.
Dishes loaded incorrectly.
Do not cover dishes with large bowls or lids.
Avoid placing very tall glasses in the corners of
the baskets.
Glasses and cups have toppled over during the Load the dishes securely.
program.
The filters are not fitted correctly.
Spots on stainless steel or silver.
Spots or films on the dishes.
Check that the filter handle is locked in the stop
position. The handle should point straight out
from the dishwasher.
Some types of food, such as mustard,
Rinse off these types of food if not starting the
mayonnaise, lemon, vinegar, salt, and dressings, dishwasher immediately. Use the Rinse and hold
can mark stainless steel if left for too long.
program.
All stainless steel can cause spots on silver if
they come into contact during dishwashing.
Aluminum can also cause spots on dishes.
In order to avoid marks and tarnishing, separate
dishes made from different metals, such as silver,
stainless steel, and aluminum.
Incorrect rinse aid dosage setting.
See the chapter Settings.
The TAB setting is activated and all-in-one
Switch all-in-one detergents or deactivate the
detergent with insufficient drying effect is being TAB setting and top up with salt and separate
used.
rinse aid. See Rinse aid in the chapter Settings.
Salt compartment empty.
Top up with salt. See the chapter Before washing
for the first time.
Incorrect water softener setting.
See Water hardness in the chapter Settings.
The water softener is leaking salt.
Check that the salt compartment lid is properly
tightened. Otherwise call the Customer Care
Center.
Too high temperature and/or too much detergent Wash crystal at a low temperature and with a
can cause etching on crystal. Unfortunately, this conservative amount of detergent. Contact the
cannot be repaired, only prevented.
detergent manufacturer.
The dishes have a sticky white/blue film.
Rinse aid dosage setting too high.
Reduce the dosage. See the chapter Settings.
If you have very soft water, you may want to dilute
the rinse aid 50:50 with water.
Spots left after washing.
Lipstick and tea can be difficult to wash off.
Use a detergent with a bleaching agent.
Detergent residue in the detergent compartment The detergent compartment was damp when
after dishwashing.
adding detergent.
The detergent compartment must be dry when
adding detergent.
The detergent compartment has been blocked. Check that the dishes are not preventing the
detergent compartment from opening.
Rattling sound when dishwashing.
18
The dishes are not correctly placed or the spray Check that the dishes are placed securely. Spin
arms are not rotating.
the spray arms to make sure they can rotate.
Problem
Possible causes
Action
"Program paused" is shown on the display.
The dishwasher door has been opened while a The dishwasher door must not be open while a
program is in progress.
program is in progress according to UL
Standards.
If you want the dishwashing program to continue,
press Start/Stop and close the door within five
seconds.
If you want to cancel the dishwashing program,
press and hold the main power switch until the
display turns off.
Water remains in the dishwasher above the filters. The filters are blocked.
Bad odor in dishwasher.
Clean the coarse and fine filters.
The filters are not fitted correctly.
Check that the filter handle is locked in the stop
position. The handle should point straight out
from the dishwasher.
Debris in the drain pump.
Clean the drain pump. See the chapter Care and
maintenance instructions.
Kink in drain hose.
Check that the hose is free from kinks and sharp
bends.
Blocked drain hose.
Loosen the drain hose from where it terminates.
Check that no debris has clogged the hose. Is
the cone-shaped part of the drain boot cut to the
maximum size of the fitting where it attaches?
Dirt around the seals and in corners.
Clean with dish brush and low foaming cleaner.
Low temperature programs have been selected Run a program with a higher temperature once
for a prolonged period.
or twice a month. Or run a self-cleaning program.
See Self-cleaning in the chapter Using the
dishwasher.
The dishes are not dry enough.
The dishwasher is connected to a garbage
disposer.
Cleaning the garbage disposer connected to the
dishwasher can eliminate odors. Follow the
disposer manufacturer's cleaning instructions.
Depending on the load, the program's drying
cycle may be insufficient.
Activate the Extra Dry option.
The dishwasher is not fully loaded.
Fully load the dishwasher.
Rinse aid needs topping up or dosage is set too Top up with rinse aid or increase the rinse aid
low.
dosage level. See the chapter Settings.
The TAB setting is activated and all-in-one
Switch all-in-one detergents or deactivate the
detergent with insufficient drying effect is being TAB setting and top up with salt and separate
used.
rinse aid. See Rinse aid in the chapter Settings.
Open the door a little once the program has
finished.
19
Technical information
Technical data
Height:
34 1/4 - 36 3/8"
Width:
24"
Depth:
22"
Weight:
120 lb (55 kg) 1)
Water pressure:
4.2–140 psi
Electrical connection: See serial number plate
Rated power:
1)
20
See serial number plate
Weight can vary due to different specifications.
Service
Limited Warranty – Residential
Appliances
ASKO Distribution North America, LLC. (“ASKO”) warrants to the original
purchaser (the “ASKO Customer”) of the ASKO product (the “ASKO
Product”), who purchased the ASKO Product from a distributor, dealer,
manufacturer’s representative or other seller who has been authorized
by ASKO, that this ASKO Product is free of defects in materials and/or
workmanship, subject to the terms and conditions set forth herein. This
Limited Warranty covers parts and labor, except as set forth in this
Limited Warranty. Service must be provided by an authorized ASKO
service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER
THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS
PROVIDED HEREIN. This Limited Warranty is valid only when the ASKO
Product is used in the country in which it was purchased. Proof of
original purchase date is required to obtain service under this Limited
Warranty.
Residential ASKO Products Used Exclusively for
Household/Personal Purposes:
Two (2) Years limited Warranty – Any warranty service claims for
residential ASKO Products must be filed with ASKO within two (2) years
from date of purchase. Service will be provided during normal business
hours.
Residential ASKO Products Not Used Exclusively for
Household/Personal Purposes or used Commercially or used in
Marine, Mobile or Aeronautical Applications:
One (1) Year limited Warranty – Any warranty service claims for ASKO
Products not used exclusively for household and personal use, or used
commercially or used in marine, mobile, or aeronautical applications
must be filed with ASKO within one (1) year from date of purchase.
Service will be provided during normal business hours.
Items excluded from warranty
This limited warranty does not cover:
1 Replacement parts or repair labor if the ASKO Product is used in
a manner that is inconsistent with published user or operator
instructions and/or installation instructions.
2 Service calls to correct the installation of the ASKO Product, to
instruct you on how to use the ASKO Product, to replace or repair
house fuses, or to correct house wiring or plumbing.
Disclaimer
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
EXPRESSLY DISCLAIMED ARE ALL OTHER EXPRESS AND IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some jurisdictions do not allow exclusion or limitations regarding
warranty rights. This Limited Warranty gives you specific legal rights
and you may have other rights that vary from jurisdiction to jurisdiction.
Attempted repair by any person other than an authorized ASKO service
company will void this Limited Warranty.
Limitation of liability
IN NO EVENT SHALL ASKO OR THE MANUFACTURER AND THEIR
RESPECTIVE PARENTS, SUBSIDIARIES AND AFFILIATES BE LIABLE
FOR CONSEQUENTIAL, INCIDENTAL, EXEMPLARY, PUNITIVE OR
SPECIAL DAMAGES. IN NO EVENT SHALL ASKO OR THE
MANUFACTURER AND THEIR RESPECTIVE PARENTS, SUBSIDIARIES
AND AFFILIATES BE LIABLE FOR DAMAGES OTHER THAN ACTUAL
DAMAGES AND IN NO EVENT FOR DAMAGES IN EXCESS OF THE
PRICE PAID FOR THE ASKO PRODUCT AS TO WHICH A CLAIM IS
MADE. Some jurisdictions do not allow the exclusion or limitation of
incidental, consequential or other damages, so these limitations and
exclusions may not apply to you. This Limited Warranty gives you
specific legal rights. You also may have other rights that vary from
jurisdiction to jurisdiction.
Troubleshooting & ASKO Customer Care
If you think you need repair service, first see the Troubleshooting
section of the Use & Care Guide. If you are unable to resolve the
problem after checking Troubleshooting, then additional help can be
obtained by calling ASKO Customer Care at 1-800-898-1879.
Read the chapter Troubleshooting before contacting the Customer
Care Center. If you have encountered a problem that you cannot
resolve, please contact your nearest dealer, see www.asko.com.
When making contact, provide the details on the serial number plate.
Include the service number (1), the article number (2), and the serial
number (3).
3 Consumable items and parts, such as filters.
4 Damage resulting from accident, alteration, misuse, abuse,
negligence, fire, flood, acts of God, improper use, improper
installation, installation not in accordance with electrical or plumbing
codes, or use of products not approved by ASKO, as well as any
attempted repair by other than authorized ASKO service companies.
5 Cosmetic damage, including scratches, dents, chips or other
damage to the finish of the ASKO Product, unless such damage
results from defects in materials or workmanship and is reported
to ASKO within 5 days from date of purchase.
6 Pickup and delivery. The ASKO Product is intended to be repaired
in your home.
7 Repairs to parts or systems resulting from unauthorized
modifications made to the ASKO Product.
8 Expenses for travel and transportation for product service if the
ASKO Product is located in a remote area where service by an
authorized ASKO service company is not available.
9 The removal and reinstallation of the ASKO Product if it is installed
in an inaccessible location or is not installed in accordance with
ASKO’s published installation instructions.
10 Replacement parts or repair labor on ASKO Products with original
model/serial numbers that have been removed, altered or cannot
be easily determined.
1
2
3
Service no.
ART. NO.
SERIAL NO.
Service after expiration of limited
warranty
For information about obtaining parts and labor after expiration of this
Limited Warranty or arising outside the scope of this Limited Warranty,
please contact ASKO Customer Care at 1-800-898-1879. After your
purchase and prior to first use of the ASKO Product, register your ASKO
Product with ASKO by utilizing the address information below. Should
you need further assistance as well, contact us at the address
information below:
ASKO Distribution North America, LLC
Customer Care Center, PO Box 44848, MADISON WI 53744
21
Notes
22
Notes
23
Quick start guide
Load the baskets
(See page 6.)
1.
Do not rinse dishes under running water before loading them in the dishwasher. Simply scrape off
large food particles before loading the dishwasher.
Check that the spray arms can rotate freely
Check also that the water supply valve is on.
2.
Don't forget! Empty the coarse filter and clean the fine filter when necessary. (See page 15.)
Add detergent
The detergent compartment has a small compartment for prewash and a large compartment for
the main wash. (See page 9.)
3.
Press and hold the main power switch until the display lights
up
4.
Check/Add rinse aid and salt
To improve washing and drying results, fill salt and rinse aid. (See page 4.)
5.
Add rinse aid
Add salt
Select a program, program mode, and any options
(See page 10.)
START
Press and hold Start/Stop until the display shows "Program started, close door in 4 sec". This
indicates that the dishwasher is ready to start. Close the door properly within four seconds, otherwise
the dishwasher will not start.
en (09-17)
7.
STOP
Press Start/Stop, close the door
24
www.askona.com
Item No.: 684077. Rev. 02. We reserve the right to make changes.
6.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising