OWNER&#39

OWNER&#39
OWNER’S
MANUAL
FASTER &
EASIER
FOR 1996
AND
NEWER
OBD II
VEHICLES
T40
DIGITAL
OBD2/CAN
CODE READER
,
OWNER S MANUAL
CHECK
Table Of Contents
1. INTRODUCTION
1.1 About OBD2 Code Reader----------------------------------------------------------3
1.2 Safety Precautions and Warnings--------------------------------------------------3
2. GENERAL INFORMATION
2.1 On-Board-Diagnostics (OBD) 2------------------------------------------------------4
2.2 Diagnostic Trouble Codes (DTCS) ------------------------------------------------5
2.3 Location Of the Data Link Conector (DLC) ------------------------------------6
2.4 OBD2 Readiness Monitors -----------------------------------------------------------6
2.5 OBD2 Monitor Readiness Status---------------------------------------------------8
2.6 OBD2 Terminology-----------------------------------------------------------------------8
3. PRODUCT INFORMATION
3.1 Tool Descri ption --------------------------------------------------------------------------10
3.2 Product Specifications -----------------------------------------------------------------10
3.3 Product Features-------------------------------------------------------------------------10
3.4 Vehicle Coverage ------------------------------------------------------------------------11
4. OPERATING INSTRUCTIONS
4.1 Reading Codes ---------------------------------------------------------------------------12
4.2 Erasing Codes----------------------------------------------------------------------------14
4.3 Retrieving I/M Readiness Status --------------------------------------------------15
4.4 Viewing VIN Number--------------------------------------------------------------------17
4.5 Rescanning Data-------------------------------------------------------------------------17
5. DIAGNOSTIC TROUBLE CODE (DTC) DEFINITIONS
5.1 OBD2 Generic DTC Definitions-----------------------------------------------------18
5.2 Part Of OBD2 Manufacturer Specific DTC Definitions -------------------47
6. WARRANTY AND SERVICE
6.1 Limited One Year Warranty ----------------------------------------------------------55
6.2 Service Procedures --------------------------------------------------------------------55
2
OBD2 CODE READER
CHECK
,
OWNER S MANUAL
1. INTRODUCTION
1.1 About OBD2 Code Reader
This powerful tool will help you take charge of your vehicle's
maintenance and servicing needs. Today vehicles use Computer Control
Systems to ensure peak per-formance and fuel-efficiency while reducing
pollutants in the vehicle's emissions. These systems also have the
ability to perform self-testing and diagnose various vehicle systems and
components, and provide valuable information to aid in servicing and
repair. However, these sophisticated systems often required expensive
tools and test equi pment in order to retrieve this information. Until now,
consumers had to rely on professional service technicians to maintain their
vehicles in top condition.
OBD2 Code Reader brings the power of the technician into your hands
in a cost-effective, easy-to-use package. Whether you are a“"put the
key in and go"”consumer, hobby mechanic or skilled DIYer, Code Reader
offers the features and functions you need to take control of your vehicle's
testing,servicing and maintenance needs.
1.2 Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the Scan
Tool, read this instruction manual first and observe the following safety
precautions at a minimum whenever working on a vehicle:
1. Always perform automotive testing in a safe environment.
2. Wear safety eye protection that meets ANSI standards.
3. Keep clothing,hair,hands,tools,test equi pment,etc,away from all moving
or hot engine parts.
4. Operate the vehicle in a well-ventilated work area; Exhaust gases are
poisonous.
5. Put blocks on drive wheels and never leave vehicle unattended while
running tests.
OBD2 CODE READER
3
,
OWNER S MANUAL
CHECK
6. Use extreme caution when working around the ignition coil, distributor
cap, ignition wires and spark plugs. These components create hazardous
voltages when the engine is running.
7. Put transmission in PARK (for automatic transmission) or NEUTRAL (for
manual transmission) and make sure the parking break is engaged.
8. Keep a fire extinguisher suitable for gasoline/chemical/electrical fires
nearby.
9. Don't connect or disconnect any test equi pment with ignition on or
engine running.
10. Keep the Scan Tool dry, clean and free from oil, water and grease.
Use a mild detergent on a clean cloth to clean the outside of the Scan
Tool, when necessary.
2. GENERAL INFORMATION
2.1 On-Board-Diagnostics (OBD) 2
The first generation of On-Board Diagnostic (called OBD I) was
developed by the California Air Resources Board (ARB) and implemented
in 1988 to monitor some of the emission control components on vehicles.
As technology and the desire to improve On-Board Diagnostic capability
increased, a new generation of On-Board Diagnostics system was
developed. This second generation of On-Board Diagnostic regulations is
called "OBD II".
The OBD II system is designed to monitor emission control systems
and key engine components by performing either continuous or periodic
tests of specific components and vehicle conditions. When a problem is
detected, the OBD II system turns on a warning lamp (MIL) on the vehicle
instrument panel to alert the driver typically by the phrase of "Check
Engine" or "Service Engine Soon". The system will also store important
information about the detected malfunction so that a technician can
4
OBD2 CODE READER
CHECK
,
OWNER S MANUAL
accurately find and fix the problem. Here below follow three pieces of
such crucial information:
Whether the Malfunction Indicator Lig ht (MIL) is commanded 'on' or
'off';
Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
Readiness Monitor status.
2.2 Diagnostic Trouble Codes (DTCs)
OBDII Diagnostic Trouble Codes are stored by the on-board computer
diagnostic system in response to a problem found in the vehicle. These
codes identify a particular problem area and are intended to provide you
with a guide as to where a fault mig ht be occurring within a vehicle. OBDII
Diagnostic Trouble Codes consist of a five-digit alphanumeric code. The
first character, a letter, identifies which control system sets the code. The
other four characters, all numbers, provide additional information on where
the DTC originated and the operating conditions that caused it to set. Here
below is an example to illustrate the structure of the digits:
OBD2 CODE READER
5
,
OWNER S MANUAL
CHECK
DTC Example
P 0 2 0 1
Systems
B=Body
C=Chassis
P=Powertrain
U=Network
Identifies what section
of the systems is
malfunctioning
Sub-systems
Code Type
Generic (SAE):
P0,P2,P34-P39
B0,B3
C0,C3
U0,U3.
Manufacturer Specific:
P1,P30-p33
B1,B2
C1,C2
U1,U2
1= Fuel and Air Metering
2= Fuel and Air Metering
3= Ignition System or Engine Misfire
4= Auxiliary Emission Controls
5= Vehicle Speed Control and Idle
Controls
6= Computer Output Circuits
7= Transmission Controls
8= Transmission Controls
2.3 Location of the Data Link Connector (DLC)
The DLC (Data Link Connector or Diagnostic Link Connector) is the
standardized 16-cavity connector where diagnostic scan tools interface
with the vehicle's on-board computer. The DLC is usually located 12
inches from the center of the instrument panel (dash), under or around
the driver's side for most vehicles. For some Asian and European vehicles,
the DLC is located behind the ashtray and the ashtray must be removed
to access the connector. Refer to the vehicle's service manual for the
location if the DLC can not be found.
2.4 OBD II Readiness Monitors
An important part of a vehicle's OBDII system is the Readiness
monitors, which are indicators used to find out if all of the emissions
6
OBD2 CODE READER
CHECK
,
OWNER S MANUAL
components have been evaluated by the OBD II system. They are running
periodic tests on specific systems and components to ensure that they
are performing within allowable limits.
Currently, there are eleven OBD II Readiness Monitors (or I/M Monitors)
defined by the U.S. Environmental Protection Agency (EPA). Not all
monitors are supported by all vehicles and the exact number of monitors
in any vehicle depends on the motor vehicle manufacturer's emissions
control strategy.
Continuous Monitors -- Some of the vehicle components or systems
are continuously tested by the vehicle's OBDII system, while others are
tested only under specific vehicle operating conditions. The continuously
monitored components listed below are always ready:
1. Misfire
2. Fuel System
3. Comprehensive Components (CCM)
Once the vehicle is running, the OBDII system is continuously checking the
above components, monitoring key engine sensors, watching for engine
misfire, and monitoring fuel demands.
Non--Continuous Monitors -- Unlike the continuous monitors,many
emissions and engine system components require the vehicle to be
operated under specific conditions before the monitor is ready. These
monitors are termed non-continuous monitors and are listed below:
1. EGR System
2. O2 Sensors
3. Catalyst
4. Evaporative System
5. O2 Sensor Heater
6. Secondary air
7. Heated Catalyst
8. A/C system
OBD2 CODE READER
7
,
OWNER S MANUAL
CHECK
2.5 OBD II Monitor Readiness Status
OBD II systems must indicate whether or not the vehicle's PCM monitor
system has completed testing on each component. Components that have
been tested will be reported as Ready, or Complete, meaning they have
been tested by the OBD II system. The purpose of recording readiness
status is to allow inspectors to determine if the vehicle's OBD II system
has tested all the components and/or systems.
The powertrain control module (PCM) sets a monitor to"Ready"
or“"Complete" after an appropriate drive cycle has been performed. The
drive cycle that enables a monitor and sets readiness codes to ready”
varies for each individual monitor. Once a monitor is set as“"Ready"
or "Complete", it will remain in this state. A number of factors, including
erasing of diagnostic trouble codes (DTCs) with a scan tool or a
disconnected battery, can result in Readiness Monitors being set to "not
ready". Since the three continuous monitors are constantly evaluating,
they will be reported as "Ready"”all of the time. If testing of a particular
supported non-continuous monitor has not been completed, the monitor
status will be reported as "Not Complete" or "Not Ready".”
In order for the OBD monitor system to become ready, the vehicle should
be driven under a variety of normal operating conditions. These operating
conditions may include a mix of hig hway driving and stop and go, city
type driving, and at least one overnig ht-off period. For specific information
on getting your vehicle's OBD monitor system ready, please consult your
vehicle owner's manual.
2.6 OBD II Definitions
Powertrain Control Module (PCM)--OBDII terminology for the onboard computer that controls engine and drive train.
8
OBD2 CODE READER
CHECK
,
OWNER S MANUAL
Malfunction Indicator Light (MIL)--Malfunction Indicator Lig ht (Service
Engine Soon, Check Engine) is a term used for the lig ht on the instrument
panel. It is to alert the driver and/or the repair technician that there is a
problem with one or more of vehicle's systems and may cause emissions
to exceed federal standards. If the MIL illuminates with a steady lig ht, it
indicates that a problem has been detected and the vehicle should be
serviced as soon as possible. Under certain conditions, the dashboard
lig ht will blink or flash. This indicates a severe problem and flashing is
intended to discourage vehicle operation. The vehicle on-board diagnostic
system can not turn the MIL off until the necessary repairs are completed
or the condition no longer exists.
DTC--Diagnostic Trouble Codes (DTC) that identify which section of the
emission control system has malfunctioned.
Enabling criteria--Also termed Enabling Conditions. They are the vehiclespecific events or conditions that must occur within the engine before the
various monitors will set,or run. Some monitors require the vehicle to follow
a prescribed "drive cycle" routine as part of the enabling criteria. Drive
cycles vary among vehicles and for each monitor in any particular vehicle.
OBDII Drive Cycle--A specific mode of vehicle operation that provides
condition required to set all the readiness monitors applicable to the vehicle
to the "ready" condition. The purpose of completing an OBD II drive cycle
is to force the vehicle to run its on-board diagnostics. Some form of a
drive cycle needs to be performed after DTCs have been erased from
the PCM's memory or after the battery has been disconnected. Running
throug h a vehicle's complete drive cycle will "set" the readiness monitors
so that future faults can be detected. Drive cycles vary depending on the
vehicle and the monitor that needs to be reset. For vehicle specific drive
cycle,consult the vehicle's Owner's Manual.
OBD2 CODE READER
9
,
OWNER S MANUAL
CHECK
3. PRODUCT INFORMATION
3.1 Tool Description
1
4
2
3
1.LCD DISPLAY--Indicates test results. It is a backlit 2-line display with 8
characters on each line.
2. ENTER BUTTON--Confirms a selection (or action) from a menu list,or
returns to the main menu.
3.SCROLL BUTTON--Scrolls throug h menu items or cancel an operation
4.OBD II CONNECTOR--Connects the Code Scanner to the vehicle's
Data Link Connector (DLC).
3.2 Product Specifications
1. Display: LCD,2 lines,8 characters,backlit
2. Operating Temperature: 0 to 50°C (-32 to 122 F°)
3. Storage Temperature: -20 to 70°C (-4 to 158 F°)
4. Power—provided via detachable heavy duty OBD II cable
5. Dimensions:
Length
Width
Heig ht
126 mm ( 5.0”)
78 mm ( 3.2”) 28mm (0.85”)
6. Weig ht: 200g (7.12 oz)
10
OBD2 CODE READER
CHECK
,
OWNER S MANUAL
3.3 Product Features
1. Works with all 1996 and newer cars & trucks that are OBD II compliant
(including the CAN,VPW,PWM,ISO and KWP 2000).
2. Reads and clears generic and manufacturer specific Diagnostic Trouble
Codes (DTCs) and turns off check engine lig ht.
3. Supports multi ple trouble code requests, generic codes, pending codes
and manufacturers' specific codes.
4. Reviews the emission readiness status of OBD monitors.
5. Retrieves VIN (Vehicle Identification No.) on 2002 and newer vehicles
that support Mode 9.
6. Determines the malfunction indicator lamp (MIL) status.
7. Easy-to-use with one plug-in; Hig hly reliable and accurate.
8. Easy-to-read crystal-clear backlit 2-line LCD display.
9. Stand-alone unit with no need for an additional laptop computer to
operate.
10. Small in size and conveniently fits in your palm.
11. Safely communicates with the on-board computer.
12. No batteries needed--powered via detachable OBD II cable.
3.4 Vehicle Coverage
The T40e OBD II Scan Tool is specially designed to work with all OBDII
compliant vehicles, including those equi pped with the next-generation
protocol-Control Area Network (CAN). It is required by EPA that All 1996
and newer vehicles (cars and lig ht trucks) sold in the United States must
be OBD II compliant and this includes all Domestic, Asian and European
vehicles.
A small number of 1994 and 1995 model year gasoline vehicles are
OBD II compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant,
check the Vehicle Emissions Control Information (VECI) Label which is
located under the hood or by the radiator of most vehicles. If the vehicle
OBD2 CODE READER
11
,
OWNER S MANUAL
CHECK
is OBD II compliant, the label will designate“"OBD II Certified". Additionally,
Government regulations mandate that all OBD II compliant vehicles must
have a "common" sixteen- pin Data Link Connector (DLC).
For your vehicle to be OBD II compliant, it must have a 16-pin DLC
(Data Link Connector) under the dash and the Vehicle Emission Control
Information Label must state that the vehicle is OBD II compliant.
4. Operating Instructions
4.1 Reading Codes:
CAUTION: Don,t connect or disconnect any test equi pment with ignition on
or engine running.
1) Turn the ignition off.
2) Locate the 16-pin Data Link Connector (DLC) and plug into the
Scan Tool cable connector to the DLC.
3) Wait for the LCD display to read C. A. N. OBD2.
C .A. N.
OBD2
4) Turn the ignition on. But do not start the engine.
5) Press the ENTER button. A sequence of messages showing the OBD
protocols may be observed on the display until the vehicle protocol is
detected.
SCAN...…
VPW
SCAN...…
PWM
SCAN...…
CAN
SCAN...…
ISO9141
SCAN...…
KWP 2000
Not all the above messages will be observed unless the protocol used
by the vehicle being tested is the last one—the ISO9141 protocol. They will
stop appearing after the vehicle protocol is detected and a confirmation
message of XXX Protocol is displayed.
12
OBD2 CODE READER
,
OWNER S MANUAL
CHECK
If a "LINK ERROR!" message shows up, turn the ignition off for
about 10 seconds, check if the Scan Tool's OBDII connector is securely
connected to the vehicle s DLC, and then turn the ignition back to on.
Repeat the procedure from step 5. If the "LINK ERROR" message
does not go away, then there may be problems for the Scan Tool to
communicate with the vehicle.
6) Wait for the main menu to come up after a brief overview displaying
the scanning results with the total number of DTCs and the overall I/M
Monitor Status.
DTC
06
I/M
YES
7) Select "DTC" from the main menu by pressing the ENTER button.
Menu:
1. DTC
If there are no Diagnostic Trouble Codes retrieved, the display will
indicate "NO CODES".
NO
CODES
If there are any Diagnostic Trouble Codes, then the total number of the
Fault Codes followed by that of the Pending Codes will be reported on the
display.
FAULT: 03
PEND: 03
8) Read the Diagnostic Trouble Codes by pressing the SCROLL button.
The first code number will display on the first line of the LCD display,
the numerical sequence of the code and the total number of the codes
OBD2 CODE READER
13
,
OWNER S MANUAL
CHECK
stored will appear on the second line. To view additional codes, press
the SCROLL button to scroll, as necessary, until all the codes have been
shown up.
P0101
01/04
If the code retrieved is a pending code, a "PD"”will show on the LCD
display in the end.
P0005 PD
01/05
To view previous codes,press the SCROLL button to scroll throug h to
the end,and then start from the first of the list.
9) Look up part 5 for Diagnostic Trouble Code Definitions. Match the
retrieved DTC(S) with those listed and read the definitions.
4.2 Erasing Codes:
CAUTION: Erasing the Diagnostic Trouble Codes allows the Scan Tool to
delete not only the codes from the vehicle's on-board computer, but also
"Freeze Frame" data and manufacturer specific enhanced data. Further,
the I/M Readiness Monitor Status for all vehicle Monitors is reset to "Not
Ready" or "Not Complete" status. Do not erase the codes before the
system has been checked completely by a technician.
1) If you decide to erase the DTCs, Select "2. ERASE" from the main
menu by pressing the ENTER button.
Menu:
2. ERASE
If the Scan Tool is not connected or no communication is established with
the vehicle yet, then refer to "Reading Codes"”from 1 to 6. at Paragraph 4.1.
14
OBD2 CODE READER
,
OWNER S MANUAL
CHECK
2) A message of "ERASE? YES NO"”comes up asking for your
confirmation.
ERASE?
YES
NO
3) If you do not want to proceed with erasing the codes, press the
SCROLL button to exit.
4) If you do wish to proceed to erase the codes, then press the ENTER
button.
5) If the codes are cleared successfully, an "ERASE DONE!"”message
will show on the display. Press the ENTER button to Return to the main
Menu list.
ERASE
DONE!
6) If the codes are not cleared, then an "ERASE FAIL!" message will
appear. Press the ENTER button to Return to the main Menu list.
ERASE
FAIL!
HOT KEY: Pressing and Holding the SCROLL button for about 3
seconds will allow you to more quickly erase the DTCs than throug h the
main menu.
4.3 RETRIEVING I/M READINESS STATUS:
Important: I/M Readiness function is used to check the operations of the
Emission System on OBD2 compliant vehicles. It is an excellent function to
use prior to having a vehicle inspected for compliance to a state emissions
program. An I/M Readiness Status result of "NO" does not necessarily
indicate that the vehicle being tested will fail the state I/M inspection. For
OBD2 CODE READER
15
,
OWNER S MANUAL
CHECK
some states, one or more such monitors may be allowed to be“"Not
Ready" to pass the emissions inspection.
"YES"”--All monitors supported on the vehicle have completed their
diagnostic testing and the MIL lig ht is not on.
"NO"--At least one monitor supported on the vehicle has not completed
its diagnostic testing, and (or) the Check Engine ( MIL) lig ht is on.
"READY"--indicates that a particular monitor being checked has
completed its diagnostic testing;
"Not RDY(NOT READY)"--indicates a particular monitor being checked
has not completed its diagnostic testing;
"N/A"--The monitor is not supported on that vehicle.
"
" --A flashing Rig ht Arrow Indicating additional information is
available on the next screen.
"
" --A flashing Left Arrow Indicating additional information is available
on the previous screen.
1) Select "3. I/M"”from the main menu by pressing the ENTER button.
Menu:
3. I/M
If the Scan Tool is not connected yet, then refer to " Reading Codes"
from 1 to 6. at Paragraph 4.1.
2) Use the SCROLL button to view the status of the MIL lig ht ("ON" or
"OFF") and the following monitors:
MISFIRE"--Misfire monitor
FUEL--Fuel System Monitor
CCM--Comprehensive Components Monitor
EGR--EGR System Monitor
O2S--O2 Sensors Monitor
AT--Catalyst Monitor
16
OBD2 CODE READER
,
OWNER S MANUAL
CHECK
EVAP--Evaporative System Monitor
HO2S--O2 Sensor Heater Monitor
2AIR-- Secondary Air Monitor
HCM--Heated Catalyst Monitor
A/C--A/C system Monitor
3) Press the ENTER button to return to the main Menu.
4.4 Viewing VIN Number
The View VIN function allows you to view the Vehicle Identification No. on
2002 and newer vehicles that support Mode 9.
1) Select 4. VIN”from the main menu by pressing the ENTER button.
Menu:
4. VIN
If the Scan Tool is not connected yet, then refer to "Reading
Codes"”from 1 to 6. at Paragraph 4.1.
2). Use the SCROLL button to view additional digits of the 17-digit string.
"
"-- A flashing Rig ht Arrow Indicating additional digits of VIN string
are available on the next screen.
"
"-- A flashing Left Arrow Indicating additional digits of VIN string
are available on the previous screen.
3) Press the ENTER button to return to the main Menu.
4.5 Rescanning Data
The RESCAN function allows you to retrieve the most current data stored
in the ECM or to re-link to the vehicle.
if communication is disconnected.
1) Select "5. RESCAN" from the main menu by pressing the ENTER
button.
OBD2 CODE READER
17
,
OWNER S MANUAL
CHECK
Menu:
5.RESCAN
If the Scan Tool is not connected yet, then refer to "Reading
Codes"”from 1 to 6. at Paragraph 4.1.
2) Use either the SCROLL or ENTER button to return to the main menu.
5. Diagnostic Trouble Code (DTC)
Definitions
The following Diagnostic Trouble Code Definitions lists provide Generic
Diagnostic Trouble Codes, and Manufacturer Specific Diagnostic Trouble
Code Definitions for CHRYSLER and TOYOTA only. others consult the
vehicle’s service manual or the enclosed CD software.
CAUTION: Parts or components should not be replaced based on only a
DTC without first consulting the vehicle service manual for more information
on possible causes of the fault as well as required testing procedures.
5.1 OBDII Generic DTC Definitions
P0001
P0002
P0003
P0004
P0005
P0006
P0007
P0008
P0009
P0010
P0011
18
OBDII Generic DTC Definitions
Fuel Volume Regulator Control Circuit Open
Fuel Volume Regulator Control Circuit Range/Performance
Fuel Volume Regulator Control Circuit Low
Fuel Volume Regulator Control Circuit Hig h
Fuel Shutoff Valve. A Control Circuit Open
Fuel Shutoff Valve. A Control Circuit Low
Fuel Shutoff Valve. A Control Circuit Hig h
Engine Position System Performance (Bank 1)
Engine Position System Performance (Bank 2)
Camshaft Position Actuator A -Bank 1 Circuit Malfunction
Camshaft Position Actuator A -Bank 1 Timing Over-Advanced
OBD2 CODE READER
CHECK
,
OWNER S MANUAL
OBDII Generic DTC Definitions
P0012
P0013
P0014
P0015
P0016
P0017
P0018
P0019
P0020
P0021
P0022
P0023
P0024
P0025
P0026
P0027
P0028
P0029
P0030
P0031
P0032
P0033
P0034
P0035
P0036
P0037
P0038
P0039
P0040
P0041
P0042
P0043
P0044
P0045
P0046
P0047
Camshaft Position Actuator A - Bank 1 Timing Over-Retarded
Camshaft Position Actuator B - Bank 1 Circuit Malfunction
Camshaft Position Actuator B - Bank 1 Timing Over-Advanced
Camshaft Position Actuator B - Bank 1 Timing Over-Retarded
Cam/Crankshaft Pos. Correlation Sensor A - Bank 1
Cam/Crankshaft Pos. Correlation Sensor B - Bank 1
Cam/Crankshaft Pos. Correlation Sensor A - Bank 2
Cam/Crankshaft Pos. Correlation Sensor B - Bank 2
Camshaft Position Actuator A - Bank 2 Circuit Malfunction
Camshaft Position Actuator A - Bank 2 Timing Over-Advanced
Camshaft Position Actuator A - Bank 2 Timing Over-Retarded
Camshaft Position Actuator B - Bank 2 Circuit Malfunction
Camshaft Position Actuator B - Bank 2 Timing Over-Advanced
Camshaft Position Actuator B - Bank 2 Timing Over-Retarded
Intake Valve-Bank 1 Control Solenoid CKT Range/Performance
Exhaust Valve-Bank1 Control Solenoid CKT Range/Performance
Intake Valve-Bank 2 Control Solenoid CKT Range/Performance
Exhaust Valve-Bank2 Control Solenoid CKT Range/Performance
HO2S Bank 1 Sensor 1 Heater Circuit
HO2S Bank 1 Sensor 1 Heater Circuit Low
HO2S Bank 1 Sensor 1 Heater Circuit Hig h
Turbo/Sup Wastegate Control Circuit
Turbo/Sup Wastegate Control Circuit Low
Turbo/Sup Wastegate Control Circuit Hig h
HO2S Bank 1 Sensor 2 Heater Circuit
HO2S Bank 1 Sensor 2 Heater Circuit Low
HO2S Bank 1 Sensor 2 Heater Circuit Hig h
Turbo/Super Charger Bypass Control CKT Performance
O2 Bank 1 Sensor 1 Signals Swapped w/ O2 Bank 2 Sensor 1
O2 Bank 1 Sensor 2 Signals Swapped w/ O2 Bank 2 Sensor 2
HO2S Bank 1 Sensor 3 Heater Circuit
HO2S Bank 1 Sensor 3 Heater Circuit Low
HO2S Bank 1 Sensor 3 Heater Circuit Hig h
Turbo/Super Charger Boost Control Solenoid A Circuit Open
Turbo/Super Charger Boost Control Solenoid A Circuit Range/ Perform
Turbo/Super Charger Boost Control Solenoid A Circuit Low
OBD2 CODE READER
19
,
OWNER S MANUAL
P0048
P0049
P0050
P0051
P0052
P0053
P0054
P0055
P0056
P0057
P0058
P0059
P0060
P0061
P0062
P0063
P0064
P0065
P0066
P0067
P0068
P0069
P0070
P0071
P0072
P0073
P0074
P0075
P0076
P0077
P0078
P0079
P0080
P0081
P0082
P0083
20
CHECK
OBDII Generic DTC Definitions
Turbo/Super Charger Boost Control Solenoid A Circuit Hig h
Turbo/Super Charger Boost Input/Turbine Speed Overspeed
HO2S Bank 2 Sensor 1 Heater Circuit
HO2S Bank 2 Sensor 1 Heater Circuit Low
HO2S Bank 2 Sensor 1 Heater Circuit Hig h
HO2S Bank 1 Sensor 1 Heater Resistance
HO2S Bank 1 Sensor 2 Heater Resistance
HO2S Bank 1 Sensor 3 Heater Resistance
HO2S Bank 2 Sensor 2 Heater Circuit
HO2S Bank 2 Sensor 2 Heater Circuit Low
HO2S Bank 2 Sensor 2 Heater Circuit Hig h
HO2S Bank 2 Sensor 1 Heater Resistance
HO2S Bank 2 Sensor 2 Heater Resistance
HO2S Bank 2 Sensor 3 Heater Resistance
HO2S Bank 2 Sensor 3 Heater Circuit
HO2S Bank 2 Sensor 3 Heater Circuit Low
HO2S Bank 2 Sensor 3 Heater Circuit Hig h
Air Assisted Injector. Control Range/Performance
Air Assisted Injector. Control Circuit Low
Air Assisted Injector. Control Circuit Hig h
MAF/MAP Sensor Throttle Position Correlation
MAP/BARO Correlation
Ambient Air Temp. Sensor Circuit
Ambient Air Temp. Sensor Range/Performance
Ambient Air Temp. Sensor Circuit Low
Ambient Air Temp. Sensor Circuit Hig h
Ambient Air Temp. Sensor CKT Intermittent
Intake Valve-Bank 1 Control Circuit
Intake Valve-Bank 1 Control Circuit Low
Intake Valve-Bank 1 Control Circuit Hig h
Exhaust Valve-Bank1 Control Circuit
Exhaust Valve-Bank1 Control Circuit Low
Exhaust Valve-Bank1 Control Circuit Hig h
Intake Valve-Bank 2 Control Circuit
Intake Valve-Bank 2 Control Circuit Low
Intake Valve-Bank 2 Control Circuit Hig h
OBD2 CODE READER
CHECK
P0084
P0085
P0086
P0087
P0088
P0089
P0090
P0091
P0092
P0093
P0094
P0095
P0096
P0097
P0098
P0099
P0100
P0101
P0102
P0103
P0104
P0105
P0106
P0107
P0108
P0109
P0110
P0111
P0112
P0113
P0114
P0115
P0116
P0117
P0118
P0119
,
OWNER S MANUAL
OBDII Generic DTC Definitions
Exhaust Valve-Bank2 Control Circuit
Exhaust Valve-Bank2 Control Circuit Low
Exhaust Valve-Bank2 Control Circuit Hig h
Fuel Rail Pressure Too Low
Fuel Rail Pressure Too Hig h
Fuel Pressure Regulator 1 Performance
Fuel Pressure Regulator 1 Control Circuit
Fuel Pressure Regulator 1 Control Circuit Low
Fuel Pressure Regulator 1 Control Circuit Hig h
Fuel System Leak (Large)
Fuel System Leak (Small)
IAT Sensor 2 Circuit
IAT Sensor 2 CKT Range/Performance
IAT Sensor 2 Circuit Low
IAT Sensor 2 Circuit Hig h
IAT Sensor 2 CKT Intermittent
MAF or VAF A Circuit Malfunction
MAF or VAF A Circuit Range/Performance
MAF or VAF A Circuit Low Input
MAF or VAF A Circuit Hig h Input
MAF or VAF A Circuit Intermittent
MAP/BARO Circuit Malfunction
MAP/BARO CKT Range/Performance
MAP/BARO Circuit Low Input
MAP/BARO Circuit Hig h Input
MAP/BARO CKT Intermittent
IAT Sensor Circuit Malfunction
IAT Sensor 1 CKT Range/Performance
IAT Sensor 1 Circuit Low Input
IAT Sensor 1 Circuit Hig h Input
IAT Sensor 1 CKT Intermittent
Engine Coolant Temp Circuit Malfunction
Engine Coolant Temp CKT Range/Performance
Engine Coolant Temp Circuit Low Input
Engine Coolant Temp Circuit Hig h Input
Engine Coolant Temp CKT Intermittent
OBD2 CODE READER
21
,
OWNER S MANUAL
P0120
P0121
P0122
P0123
P0124
P0125
P0126
P0127
P0128
P0129
P0130
P0131
P0132
P0133
P0134
P0135
P0136
P0137
P0138
P0139
P0140
P0141
P0142
P0143
P0144
P0145
P0146
P0147
P0148
P0149
P0150
P0151
P0152
P0153
P0154
P0155
22
CHECK
OBDII Generic DTC Definitions
TPS/Pedal Position Sensor A Circuit Malfunction
TPS/Pedal Position Sensor A CKT Range/Performance
TPS/Pedal Position Sensor A Circuit Low Input
TPS/Pedal Position Sensor A Circuit Hig h Input
TPS/Pedal Position Sensor A CKT Intermittent
Closed Loop Fuel Ctrl Insufficient Coolant Temp
Coolant Temp Insufficient Stable Operation
IAT Sensor Too Hig h
Coolant Temp Below Thermostat Regulating Temp
Barometric Pressure Too Low
O2 Sensor Circuit Malfunction (Bank 1 Sensor 1)
O2 Sensor Circuit Low Volts (Bank 1 Sensor 1)
O2 Sensor Circuit Hig h Volts (Bank 1 Sensor 1)
O2 Sensor CKT Slow Response (Bank 1 Sensor 1)
O2 Sensor CKT No Activity (Bank 1 Sensor 1)
O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
O2 Sensor Circuit Malfunction (Bank 1 Sensor 2)
O2 Sensor Circuit Low Volts (Bank 1 Sensor 2)
O2 Sensor Circuit Hig h Volts (Bank 1 Sensor 2)
O2 Sensor CKT Slow Response (Bank 1 Sensor 2)
O2 Sensor CKT No Activity (Bank 1 Sensor 2)
O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)
O2 Sensor Circuit Low Volts (Bank 1 Sensor 3)
O2 Sensor Circuit Hig h Volts (Bank 1 Sensor 3)
O2 Sensor CKT Slow Response (Bank 1 Sensor 3)
O2 Sensor CKT No Activity (Bank 1 Sensor 3)
O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 3)
Fuel Delivery Malfunction
Fuel Timing Malfunction
O2 Sensor Circuit Malfunction (Bank 2 Sensor 1)
O2 Sensor Circuit Low Volts (Bank 2 Sensor 1)
O2 Sensor Circuit Hig h Volts (Bank 2 Sensor 1)
O2 Sensor CKT Slow Response (Bank 2 Sensor 1)
O2 Sensor CKT No Activity (Bank 2 Sensor 1)
O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
OBD2 CODE READER
CHECK
P0156
P0157
P0158
P0159
P0160
P0161
P0162
P0163
P0164
P0165
P0166
P0167
P0168
P0169
P0170
P0171
P0172
P0173
P0174
P0175
P0176
P0177
P0178
P0179
P0180
P0181
P0182
P0183
P0184
P0185
P0186
P0187
P0188
P0189
P0190
P0191
,
OWNER S MANUAL
OBDII Generic DTC Definitions
O2 Sensor Circuit Malfunction (Bank 2 Sensor 2)
O2 Sensor Circuit Low Volts (Bank 2 Sensor 2)
O2 Sensor Circuit Hig h Volts (Bank 2 Sensor 2)
O2 Sensor CKT Slow Response (Bank 2 Sensor 2)
O2 Sensor CKT No Activity (Bank 2 Sensor 2)
O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)
O2 Sensor Circuit Low Volts (Bank 2 Sensor 3)
O2 Sensor Circuit Hig h Volts (Bank 2 Sensor 3)
O2 Sensor CKT Slow Response (Bank 2 Sensor 3)
O2 Sensor CKT No Activity (Bank 2 Sensor 3)
O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)
Engine Fuel Temperature Too Hig h
Fuel Composition Incorrect
Fuel Trim Malfunction (Bank 1)
System Too Lean (Bank 1)
System Too Rich (Bank 1)
Fuel Trim Malfunction (Bank 2)
System Too Lean (Bank 2)
System Too Rich (Bank 2)
Fuel Compensation Sensor Circuit Malfunction
Fuel Compensation Sensor CKT Range/Performance
Fuel Compensation Sensor Circuit Low Input
Fuel Compensation Sensor Circuit Hig h Input
Fuel Temperature Sensor A Circuit Malfunction
Fuel Temperature Sensor A CKT Range/Performance
Fuel Temperature Sensor A Circuit Low Input
Fuel Temperature Sensor A Circuit Hig h Input
Fuel Temperature Sensor A CKT Intermittent
Fuel Temperature Sensor B Circuit Malfunction
Fuel Temperature Sensor B CKT Range/Performance
Fuel Temperature Sensor B Circuit Low Input
Fuel Temperature Sensor B Circuit Hig h Input
Fuel Temperature Sensor B CKT Intermittent
Fuel Rail Pressure Sensor Circuit Malfunction
Fuel Rail Pressure Sensor CKT Range/Performance
OBD2 CODE READER
23
,
OWNER S MANUAL
P0192
P0193
P0194
P0195
P0196
P0197
P0198
P0199
P0200
P0201
P0202
P0203
P0204
P0205
P0206
P0207
P0208
P0209
P0210
P0211
P0212
P0213
P0214
P0215
P0216
P0217
P0218
P0219
P0220
P0221
P0222
P0223
P0224
P0225
P0226
P0227
24
CHECK
OBDII Generic DTC Definitions
Fuel Rail Pressure Sensor Circuit Low Input
Fuel Rail Pressure Sensor Circuit Hig h Input
Fuel Rail Pressure Sensor CKT Intermittent
Engine Oil Temp Sensor Circuit Malfunction
Engine Oil Temp Sensor CKT Range/Performance
Engine Oil Temp Sensor Circuit Low Input
Engine Oil Temp Sensor Circuit Hig h Input
Engine Oil Temp Sensor CKT Intermittent
Injector Circuit Open
Injector Circuit Open Cylinder 1
Injector Circuit Open Cylinder 2
Injector Circuit Open Cylinder 3
Injector Circuit Open Cylinder 4
Injector Circuit Open Cylinder 5
Injector Circuit Open Cylinder 6
Injector Circuit Open Cylinder 7
Injector Circuit Open Cylinder 8
Injector Circuit Open Cylinder 9
Injector Circuit Open Cylinder 10
Injector Circuit Open Cylinder 11
Injector Circuit Open Cylinder 12
Cold Start Injector 1 Malfunction
Cold Start Injector 2 Malfunction
Engine Shutoff Solenoid Malfunction
Injection Timing Control Circuit Malfunction
Engine Overtemp Condition
Transmission Overtemp Condition
Engine Overspeed Condition
TPS/Pedal Position Sensor/Switch B Circuit Malfunction
TPS/Pedal Position Sensor/Switch B CKT Range/Performance
TPS/Pedal Position Sensor/Switch B Circuit Low Input
TPS/Pedal Position Sensor/Switch B Circuit Hig h Input
TPS/Pedal Position Sensor/Switch B CKT Intermittent
TPS/Pedal Position Sensor/Switch C Circuit Malfunction
TPS/Pedal Position Sensor/Switch C CKT Range/Performance
TPS/Pedal Position Sensor/Switch C Circuit Low Input
OBD2 CODE READER
CHECK
P0228
P0229
P0230
P0231
P0232
P0233
P0234
P0235
P0236
P0237
P0238
P0239
P0240
P0241
P0242
P0243
P0244
P0245
P0246
P0247
P0248
P0249
P0250
P0251
P0252
P0253
P0254
P0255
P0256
P0257
P0258
P0259
P0260
P0261
P0262
P0263
,
OWNER S MANUAL
OBDII Generic DTC Definitions
TPS/Pedal Position Sensor/Switch C Circuit Hig h Input
TPS/Pedal Position Sensor/Switch C CKT Intermittent
Fuel Pump Primary Circuit Malfunction
Fuel Pump Secondary Circuit Low
Fuel Pump Secondary Circuit Hig h
Fuel Pump Secondary Circuit Intermittent Ckt
Engine Overboost Condition
Turbo/Super Boost Sensor A Circuit Malfunction
Turbo/Super Boost Sensor A CKT Range/Performance
Turbo/Super Boost Sensor A Circuit Low Input
Turbo/Super Boost Sensor A Circuit Hig h Input
Turbo/Super Boost Sensor B Circuit Malfunction
Turbo/Super Boost Sensor B CKT Range/Performance
Turbo/Super Boost Sensor B Circuit Low Input
Turbo/Super Boost Sensor B Circuit Hig h Input
Turbo/Sup Wastegate Solenoid A Malfunction
Turbo/Sup Wastegate Solenoid A Range/Performance
Turbo/Sup Wastegate Solenoid A Low
Turbo/Sup Wastegate Solenoid A Hig h
Turbo/Sup Wastegate Solenoid B Malfunction
Turbo /Sup Wastegate Solenoid B Range/Performance
Turbo/Sup Wastegate Solenoid B Low
Turbo/Sup Wastegate Solenoid B Hig h
Injection Pump Metering Control A
Injection Pump Metering Control A Range/Performance
Injection Pump Metering Control A Low
Injection Pump Metering Control A Hig h
Injection Pump Metering Control A Intermittent (Cam/Rotor/Injector)
Injection Pump Metering Control B Malfunction (Cam/Rotor/Injector)
Injection Pump Metering Control B Range/Performance
Injection Pump Metering Control B Low (Cam/Rotor/Injector)
Injection Pump Metering Control B Hig h (Cam/Rotor/Injector)
Injection Pump Metering Control B Intermittent (Cam/Rotor/Injector)
Cylinder 1 Injector Control Circuit Low
Cylinder 1 Injector Control Circuit Hig h
Cylinder 1 Contribution Balance Fault
OBD2 CODE READER
25
,
OWNER S MANUAL
P0264
P0265
P0266
P0267
P0268
P0269
P0270
P0271
P0272
P0273
P0274
P0275
P0276
P0277
P0278
P0279
P0280
P0281
P0282
P0283
P0284
P0285
P0286
P0287
P0288
P0289
P0290
P0291
P0292
P0293
P0294
P0295
P0296
P0297
P0298
P0299
26
CHECK
OBDII Generic DTC Definitions
Cylinder 2 Injector Control Circuit Low
Cylinder 2 Injector Control Circuit Hig h
Cylinder 2 Contribution Balance Fault
Cylinder 3 Injector Control Circuit Low
Cylinder 3 Injector Control Circuit Hig h
Cylinder 3 Contribution Balance Fault
Cylinder 4 Injector Control Circuit Low
Cylinder 4 Injector Control Circuit Hig h
Cylinder 4 Contribution Balance Fault
Cylinder 5 Injector Control Circuit Low
Cylinder 5 Injector Control Circuit Hig h
Cylinder 5 Contribution Balance Fault
Cylinder 6 Injector Control Circuit Low
Cylinder 6 Injector Control Circuit Hig h
Cylinder 6 Contribution Balance Fault
Cylinder 7 Injector Control Circuit Low
Cylinder 7 Injector Control Circuit Hig h
Cylinder 7 Contribution Balance Fault
Cylinder 8 Injector Control Circuit Low
Cylinder 8 Injector Control Circuit Hig h
Cylinder 8 Contribution Balance Fault
Cylinder 9 Injector Control Circuit Low
Cylinder 9 Injector Control Circuit Hig h
Cylinder 9 Contribution Balance Fault
Cylinder 10 Injector Control Circuit Low
Cylinder 10 Injector Control Circuit Hig h
Cylinder 10 Contribution Balance Fault
Cylinder 11 Injector Control Circuit Low
Cylinder 11 Injector Control Circuit Hig h
Cylinder 11 Contribution Balance Fault
Cylinder 12 Injector Control Circuit Low
Cylinder 12 Injector Control Circuit Hig h
Cylinder 12 Contribution Balance Fault
Vehicle Overspeed Error
Engine Oil Temperature Too Hig h
Turbo/Super Charger UnderBoost
OBD2 CODE READER
CHECK
P0300
P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
P0309
P0310
P0311
P0312
P0313
P0314
P0315
P0316
P0317
P0318
P0319
P0320
P0321
P0322
P0323
P0324
P0325
P0326
P0327
P0328
P0329
P0330
P0331
P0332
P0333
P0334
P0335
,
OWNER S MANUAL
OBDII Generic DTC Definitions
Random/Multi ple Cylinder Misfire Detected
Cylinder 1 Misfire Detected
Cylinder 2 Misfire Detected
Cylinder 3 Misfire Detected
Cylinder 4 Misfire Detected
Cylinder 5 Misfire Detected
Cylinder 6 Misfire Detected
Cylinder 7 Misfire Detected
Cylinder 8 Misfire Detected
Cylinder 9 Misfire Detected
Cylinder 10 Misfire Detected
Cylinder 11 Misfire Detected
Cylinder 12 Misfire Detected
Misfire Detected Low Fuel Level
Misfire Detected Cyl. not Specific
Crankshaft Position System Variation Not Learned
Misfire Detected 1st 1000 Revs.
Roug h Road Hardware Not Present
Roug h Road Sensor A Signal Circuit
Roug h Road Sensor B
Ignition/Dist Engine Speed Input Circuit Malfunction
Ignition/Dist Engine Speed Input CKT Range/Performance
Ignition/Dist Engine Speed Input Circuit No Signal
Ignition/Dist Engine Speed Input CKT Intermittent
Knock Control System Malfunction
Knock Sensor 1 Circuit Malfunction Bank 1 or 1 Sensor
Knock Sensor 1 CKT Range/Performance Bank 1 or 1 Sensor
Knock Sensor 1 Circuit Low Input Bank 1 or 1 Sensor
Knock Sensor 1 Circuit Hig h Input Bank 1 or 1 Sensor
Knock Sensor 1 CKT Intermittent Bank 1 or 1 Sensor
Knock Sensor 2 Circuit Malfunction (Bank 2)
Knock Sensor 2 CKT Range/Performance (Bank 2)
Knock Sensor 2 Circuit Low Input (Bank 2)
Knock Sensor 2 Circuit Hig h Input (Bank 2)
Knock Sensor 2 CKT Intermittent (Bank 2)
Crankshaft Position Sensor A Circuit Malfunction
OBD2 CODE READER
27
,
OWNER S MANUAL
P0336
P0337
P0338
P0339
P0340
P0341
P0342
P0343
P0344
P0345
P0346
P0347
P0348
P0349
P0350
P0351
P0352
P0353
P0354
P0355
P0356
P0357
P0358
P0359
P0360
P0361
P0362
P0363
P0365
P0366
P0367
P0368
P0369
P0370
P0371
P0372
28
CHECK
OBDII Generic DTC Definitions
Crankshaft Position Sensor A CKT Range/Performance
Crankshaft Position Sensor A Circuit Low Input
Crankshaft Position Sensor A Circuit Hig h Input
Crankshaft Position Sensor A CKT Intermittent
Camshaft Position Sensor A - Bank 1 Circuit Malfunction
Camshaft Position Sensor A - Bank 1 CKT Range/Performance
Camshaft Position Sensor A - Bank 1 Circuit Low Input
Camshaft Position Sensor A - Bank 1 Circuit Hig h Input
Camshaft Position Sensor A - Bank 1 CKT Intermittent
Camshaft Position Sensor A - Bank 2 Circuit Malfunction
Camshaft Position Sensor A - Bank 2 CKT Range/Performance
Camshaft Position Sensor A - Bank 2 Circuit Low Input
Camshaft Position Sensor A - Bank 2 Circuit Hig h Input
Camshaft Position Sensor A - Bank 2 CKT Intermittent
Ignition Coil Primary/Secondary Circuit Malfunction
Ignition Coil A Primary/Secondary Circuit Malfunction
Ignition Coil B Primary/Secondary Circuit Malfunction
Ignition Coil C Primary/Secondary Circuit Malfunction
Ignition Coil D Primary/Secondary Circuit Malfunction
Ignition Coil E Primary/Secondary Circuit Malfunction
Ignition Coil F Primary/Secondary Circuit Malfunction
Ignition Coil G Primary/Secondary Circuit Malfunction
Ignition Coil H Primary/Secondary Circuit Malfunction
Ignition Coil I Primary/Secondary Circuit Malfunction
Ignition Coil J Primary/Secondary Circuit Malfunction
Ignition Coil K Primary/Secondary Circuit Malfunction
Ignition Coil L Primary/Secondary Circuit Malfunction
Misfire Detected Fueling Disabled
Camshaft Position Sensor B - Bank 1 Circuit Malfunction
Camshaft Position Sensor B - Bank 1 CKT Range/Performance
Camshaft Position Sensor B - Bank 1 Circuit Low Input
Camshaft Position Sensor B - Bank 1 Circuit Hig h Input
Camshaft Position Sensor B - Bank 1 CKT Intermittent
Timing Reference Hig h Resolution Signal A Malfunction
Timing Reference Hig h Resolution Signal A Too Many Pulses
Timing Reference Hig h Resolution Signal A Too Few Pulses
OBD2 CODE READER
CHECK
P0373
P0374
P0375
P0376
P0377
P0378
P0379
P0380
P0381
P0382
P0383
P0384
P0385
P0386
P0387
P0388
P0389
P0390
P0391
P0392
P0393
P0394
P0400
P0401
P0402
P0403
P0404
P0405
P0406
P0407
P0408
P0409
P0410
P0411
P0412
P0413
,
OWNER S MANUAL
OBDII Generic DTC Definitions
Timing Reference Hig h Resolution Signal A Erratic Pulses
Timing Reference Hig h Resolution Signal A No Pulses
Timing Reference Hig h Resolution Signal B Malfunction
Timing Reference Hig h Resolution Signal B Too Many Pulses
Timing Reference Hig h Resolution Signal B Too Few Pulses
Timing Reference Hig h Resolution Signal B Erratic Pulses
Timing Reference Hig h Resolution Signal B No Pulses
Glow Plug/Heater CKT A Malfunction
Glow Plug/Heater Indicator Circuit Malfunction
Glow Plug/Heater CKT B Malfunction
Glow Plug Module Control Circuit Low
Glow Plug Module Control Circuit Hig h
Crankshaft Position Sensor B Circuit Malfunction
Crankshaft Position Sensor B CKT Range/Performance
Crankshaft Position Sensor B Circuit Low Input
Crankshaft Position Sensor B Circuit Hig h Input
Crankshaft Position Sensor B CKT Intermittent
Camshaft Position Sensor B - Bank 2 Circuit Malfunction
Camshaft Position Sensor B - Bank 2 CKT Range/Performance
Camshaft Position Sensor B - Bank 2 Circuit Low Input
Camshaft Position Sensor B - Bank 2 Circuit Hig h Input
Camshaft Position Sensor B - Bank 2 CKT Intermittent
EGR Flow Malfunction
EGR Flow Insufficient
EGR Flow Excessive
EGR Flow Circuit Malfunction
EGR Flow CKT Range/Performance
EGR Flow Sensor A Circuit Low Input
EGR Flow Sensor A Circuit Hig h Input
EGR Flow Sensor B Circuit Low Input
EGR Flow Sensor B Circuit Hig h Input
EGR Flow Sensor A Circuit
Secondary Air Injection System Malfunction
Secondary Air Injection System Incorrect Flow
Secondary Air Injection System Valve A Malfunction
Secondary Air Injection System Valve A CKT Open
OBD2 CODE READER
29
,
OWNER S MANUAL
P0414
P0415
P0416
P0417
P0418
P0419
P0420
P0421
P0422
P0423
P0424
P0425
P0426
P0427
P0428
P0429
P0430
P0431
P0432
P0433
P0434
P0435
P0436
P0437
P0438
P0439
P0440
P0441
P0442
P0443
P0444
P0445
P0446
P0447
P0448
P0449
30
CHECK
OBDII Generic DTC Definitions
Secondary Air Injection System Valve A CKT Short
Secondary Air Injection System Valve B Malfunction
Secondary Air Injection System Valve B CKT Open
Secondary Air Injection System Valve B CKT Short
Secondary Air Injection System Relay A Malfunction
Secondary Air Injection System Relay B Malfunction
Catalyst Efficiency Below Threshold (Bank 1)
Warm Up Catalyst Below Threshold (Bank 1)
Main Catalyst Below Threshold (Bank 1)
Heated Catalyst Below Threshold (Bank 1)
Heated Catalyst Temp Below Threshold (Bank 1)
Catalyst Temp. Sensor (Bank 1 Sensor 1)
Catalyst Temp. Sensor Performance (Bank 1 Sensor 1)
Catalyst Temp. Sensor Circuit Low (Bank 1 Sensor 1)
Catalyst Temp. Sensor Circuit Hig h (Bank 1 Sensor 1)
Catalyst Heater Control (Bank 1)
Catalyst Efficiency Below Threshold (Bank 2)
Warm Up Catalyst Below Threshold (Bank 2)
Main Catalyst Below Threshold (Bank 2)
Heated Catalyst Below Threshold (Bank 2)
Heated Catalyst Temp Below Threshold (Bank 2)
Catalyst Temp. Sensor (Bank 2 Sensor 1)
Catalyst Temp. Sensor Performance (Bank 2 Sensor 1)
Catalyst Temp. Sensor Circuit Low (Bank 2 Sensor 1)
Catalyst Temp. Sensor Circuit Hig h (Bank 2 Sensor 1)
Catalyst Heater Control (Bank 2)
EVAP Emission Control System Malfunction
EVAP Emission Control System Purge Flow Fault
EVAP Emission Control System Leak (Small)
EVAP Emission Control System Purge Valve C Fault
EVAP Emission Control System Purge Valve C Open
EVAP Emission Control System Purge Valve C Short
EVAP Emission Control System Vent Circuit Malf
EVAP Emission Control System Vent Circuit Open
EVAP Emission Control System Vent Circuit Short
EVAP Emission Control System Vent Vlv/Sol Malf
OBD2 CODE READER
CHECK
P0450
P0451
P0452
P0453
P0454
P0455
P0456
P0457
P0458
P0459
P0460
P0461
P0462
P0463
P0464
P0465
P0466
P0467
P0468
P0469
P0470
P0471
P0472
P0473
P0474
P0475
P0476
P0477
P0478
P0479
P0480
P0481
P0482
P0483
P0484
P0485
,
OWNER S MANUAL
OBDII Generic DTC Definitions
EVAP Emission Control System Pres Sensor Fault
EVAP Emission Control System Pres Sensor Range
EVAP Emission Control System Pres Sensor Low
EVAP Emission Control System Pres Sensor Hig h
EVAP Emission Control System Pres Sensor Erratic
EVAP Emission Control System Leak (Large)
EVAP Emission Control System Leak Very Small
EVAP Emission Control System Leak Cap Loose/Off
EVAP System Canister Purge Sol Circuit Low
EVAP System Canister Purge Sol Circuit Hig h
Fuel Level Sensor A Circuit Malfunction
Fuel Level Sensor A CKT Range/Performance
Fuel Level Sensor A Circuit Low Input
Fuel Level Sensor A Circuit Hig h Input
Fuel Level Sensor A CKT Intermittent
EVAP Emission Purge Flow Sensor Circuit Malfunction
EVAP Emission Purge Flow Sensor CKT Range/Performance
EVAP Emission Purge Flow Sensor Circuit Low Input
EVAP Emission Purge Flow Sensor Circuit Hig h Input
EVAP Emission Purge Flow Sensor CKT Intermittent
Exhaust Pressure Sensor Circuit Malfunction
Exhaust Pressure Sensor CKT Range/Performance
Exhaust Pressure Sensor Circuit Low Input
Exhaust Pressure Sensor Circuit Hig h Input
Exhaust Pressure Sensor CKT Intermittent
Exhaust Pressure Control Valve Circuit Malfunction
Exhaust Pressure Control Valve CKT Range/Performance
Exhaust Pressure Control Valve Circuit Low Input
Exhaust Pressure Control Valve Circuit Hig h Input
Exhaust Pressure Control Valve CKT Intermittent
Cooling Fan 1 Control Circuit
Cooling Fan 2 Control Circuit
Cooling Fan 3 Control Circuit
Control Fan Rationality Check Malfunction
Control Fan CKT Over Current
Control Fan Power/Ground Circuit Malfunction
OBD2 CODE READER
31
,
OWNER S MANUAL
P0486
P0487
P0488
P0489
P0490
P0491
P0492
P0493
P0494
P0495
P0496
P0497
P0498
P0499
P0500
P0501
P0502
P0503
P0504
P0505
P0506
P0507
P0508
P0509
P0510
P0511
P0512
P0513
P0514
P0515
P0516
P0517
P0518
P0519
P0520
P0521
32
CHECK
OBDII Generic DTC Definitions
EGR System Sensor B Circuit
EGR TPS Control Circuit
EGR TPS Control CKT Range/Performance
EGR Control Circuit Low
EGR Control Circuit Hig h
Secondary Air System (Bank 1)
Secondary Air System (Bank 2)
Fan Speed Overspeed
Fan Speed Low
Fan Speed Hig h
EVAP Emission Hig h Purge Flow Fault
EVAP Emission Low Purge Flow Fault
EVAP Emission Vent Vlv/Sol Malf Circuit Low
EVAP Emission Vent Vlv/Sol Malf Circuit Hig h
Vehicle Speed Sensor A Malfunction
Vehicle Speed Sensor A Range/Performance
Vehicle Speed Sensor A Circuit Low Input
Vehicle Speed Sensor A Erratic/Hig h
Brake Switch A Brake Switch B Correlation
Idle Control System Malfunction
Idle Control System RPM Low
Idle Control System RPM Hig h
Idle Control System Circuit Low
Idle Control System Circuit Hig h
Closed Throttle Position Switch
Idle Air Control Circuit
Starter Signal Circuit
Immobilizer Incorrect
Battery Temperature Sensor CKT Range/Performance
Battery Temperature Sensor Circuit
Battery Temperature Circuit Low
Battery Temperature Circuit Hig h
Idle Air Control CKT Intermittent
Idle Air Control System Performance
Engine Oil Pressure Sensor/Switch Circuit Malfunction
Engine Oil Pressure Sensor/Switch Range/Performance
OBD2 CODE READER
CHECK
P0522
P0523
P0524
P0525
P0526
P0527
P0528
P0529
P0530
P0531
P0532
P0533
P0534
P0535
P0536
P0537
P0538
P0539
P0540
P0541
P0542
P0543
P0544
P0545
P0546
P0547
P0548
P0549
P0550
P0551
P0552
P0553
P0554
P0555
P0556
P0557
,
OWNER S MANUAL
OBDII Generic DTC Definitions
Engine Oil Pressure Sensor/Switch Low Voltage
Engine Oil Pressure Sensor/Switch Hig h Voltage
Engine Oil Pressure Too Low
Cruise Servo CKT Range/Performance
Fan Speed Sensor Circuit
Fan Speed Sensor CKT Range/Performance
Fan Speed Sensor Circuit No Signal
Fan Speed Sensor CKT Intermittent
A/C Refrigerant Pressure Sensor A Circuit Malfunction
A/C Refrigerant Pressure Sensor A CKT Range/Performance
A/C Refrigerant Pressure Sensor A Circuit Low Input
A/C Refrigerant Pressure Sensor A Circuit Hig h Input
A/C Refrigerant Charge Loss
A/C Evaporator Temperature Sensor Circuit
A/C Evaporator Temperature Sensor CKT Range/Performance
A/C Evaporator Temperature Sensor Circuit Low
A/C Evaporator Temperature Sensor Circuit Hig h
A/C Evaporator Temperature Sensor CKT Intermittent
Intake Air Heater A Circuit
Intake Air Heater A Circuit Low
Intake Air Heater A Circuit Hig h
Intake Air Heater A Circuit Open
Exhaust Gas Temp. Sensor Circuit (Bank 1 Sensor 1)
Exhaust Gas Temp. Sensor Circuit Low (Bank 1 Sensor 1)
Exhaust Gas Temp. Sensor Circuit Hig h (Bank 1 Sensor 1)
Exhaust Gas Temp. Sensor Circuit (Bank 2 Sensor 1)
Exhaust Gas Temp. Sensor Circuit Low (Bank 2 Sensor 1)
Exhaust Gas Temp. Sensor Circuit Hig h (Bank 2 Sensor 1)
Power Steering Pres Sensor Circuit Malfunction
Power Steering Pres Sensor CKT Range/Performance
Power Steering Pres Sensor Circuit Low Input
Power Steering Pres Sensor Circuit Hig h Input
Power Steering Pres Sensor CKT Intermittent
Brake Booster Pressure Sensor Circuit
Brake Booster Pressure Sensor CKT Range/Performance
Brake Booster Pressure Sensor Circuit Low Input
OBD2 CODE READER
33
,
OWNER S MANUAL
P0558
P0559
P0560
P0561
P0562
P0563
P0564
P0565
P0566
P0567
P0568
P0569
P0570
P0571
P0572
P0573
P0574
P0575
P0576
P0577
P0578
P0579
P0580
P0581
P0582
P0583
P0584
P0585
P0586
P0587
P0588
P0589
P0590
P0591
P0592
P0593
34
CHECK
OBDII Generic DTC Definitions
Brake Booster Pressure Sensor Circuit Hig h Input
Brake Booster Pressure Sensor CKT Intermittent
System Voltage Malfunction
System Voltage Unstable
System Voltage Low
System Voltage Hig h
Cruise Control Multi-Function. Input A Signal Error
Cruise Control On Signal Malfunction
Cruise Control Off Signal Malfunction
Cruise Control Resume Signal Malfunction
Cruise Control Set Signal Malfunction
Cruise Control Coast Signal Malfunction
Cruise Control Acceleration Signal Error
Brake Switch A Circuit Malfunction
Brake Switch A Circuit Low Input
Brake Switch A Circuit Hig h Input
Cruise Control Vehicle Speed Too Hig h
Cruise Control Circuit Malfunction
Cruise Control Circuit Low Input
Cruise Control Circuit Hig h Input
Cruise Control Multi-Function Input A Circuit Stuck
Cruise Control Multi-Function Input A CKT Range/Performance
Cruise Control Multi-Function Input A Circuit Low
Cruise Control Multi-Function Input A Circuit Hig h
Cruise Control Vacuum Control Circuit Open
Cruise Control Vacuum Control Circuit Low
Cruise Control Vacuum Control Circuit Hig h
Cruise Control Multi-Function Input Correlation
Cruise Control Vent Control Circuit Open
Cruise Control Vent Control Circuit Low
Cruise Control Vent Control Circuit Hig h
Cruise Control Multi-Function Input B Circuit
Cruise Control Multi-Function Input B Circuit Stuck
Cruise Control Multi-Function Input B CKT Range/Performance
Cruise Control Multi-Function Input B Circuit Low
Cruise Control Multi-Function Input B Circuit Hig h
OBD2 CODE READER
CHECK
P0594
P0595
P0596
P0597
P0598
P0599
P0600
P0601
P0602
P0603
P0604
P0605
P0606
P0607
P0608
P0609
P0610
P0611
P0612
P0613
P0614
P0615
P0616
P0617
P0618
P0619
P0620
P0621
P0622
P0623
P0624
P0625
P0626
P0627
P0628
P0629
,
OWNER S MANUAL
OBDII Generic DTC Definitions
Cruise Control Servo Control Circuit Open
Cruise Control Servo Control Circuit Low
Cruise Control Servo Control Circuit Hig h
Cruise Control Circuit Open
Cruise Control Circuit Low
Cruise Control Circuit Hig h
Serial Communication Link Malfunction
Internal Control Module Memory Check Sum Error
Control Module Programming Error
PCM Keep Alive Memory (KAM) Error
PCM Random Access Memory (RAM) Error
PCM Read Only Memory (ROM) Error
PCM Processor Fault
Control Module Performance
Control Module VSS Output A Malfunction
Control Module VSS Output B Malfunction
Control Module Vehicle Options Malfunction
Injector Control Module Performance
Injector Control Module Relay Control
TCM Processor Fault
ECM/TCM Incompatible
Starter Relay Circuit
Starter Relay Circuit Low
Starter Relay Circuit Hig h
Alternative Fuel Module (KAM) Error
Alternative Fuel Module Memory
Generator Control Malfunction
Generator L-Term. Lamp Control
Generator F-Term. Field F Control
Generator Lamp Control Circuit
Fuel Cap Lamp Circuit
Generator F-Term. Circuit Low
Generator F-Term. Circuit Hig h
Fuel Pump A Control Circuit Open
Fuel Pump A Control Circuit Low
Fuel Pump A Control Circuit Hig h
OBD2 CODE READER
35
,
OWNER S MANUAL
P0630
P0631
P0632
P0633
P0634
P0635
P0636
P0637
P0638
P0639
P0640
P0641
P0642
P0643
P0644
P0645
P0646
P0647
P0648
P0649
P0650
P0651
P0652
P0653
P0654
P0655
P0656
P0657
P0658
P0659
P0660
P0661
P0662
P0663
P0664
P0665
36
CHECK
OBDII Generic DTC Definitions
PCM VIN Not Program. Or Mismatch
TCM VIN Not Program. Or Mismatch
Odometer Code Not Programmed ECM/PCM
Immobilizer Code Not Programmed ECM/PCM
PCM/ECM/TCM Internal Temp. Too Hig h
Power Steering Control Circuit
Power Steering Control Circuit Low
Power Steering Control Circuit Hig h
Throttle Actuator Range/Performance (Bank 1)
Throttle Actuator Range/Performance (Bank 2)
Intake Air Heater Control Circuit
Sensor A Reference Voltage Circuit Open
Sensor A Reference Voltage Circuit Low
Sensor A Reference Voltage Circuit Hig h
Driver Display Serial Communication Link
A/C Clutch Relay Control Circuit
A/C Clutch Relay Control Circuit Low
A/C Clutch Relay Control Circuit Hig h
Immobilizer Lamp Circuit
Cruise Control Lamp Circuit
MIL Control Circuit Malfunction
Sensor B Reference Voltage Circuit Open
Sensor B Reference Voltage Circuit Low
Sensor B Reference Voltage Circuit Hig h
Engine RPM Circuit Malfunction
Engine Hot Lamp Output Circuit Malfunction
Fuel Level Output Circuit Malfunction
Actuator Supply Voltage A Circuit Open
Actuator Supply Voltage A Circuit Low
Actuator Supply Voltage A Circuit Hig h
Intake Man Tuning Control CKT Open (Bank 1)
Intake Man Tuning Control CKT Low (Bank 1)
Intake Man Tuning Control CKT Hig h (Bank 1)
Intake Man Tuning Control CKT Open (Bank 2)
Intake Man Tuning Control CKT Low (Bank 2)
Intake Man Tuning Control CKT Hig h (Bank 2)
OBD2 CODE READER
CHECK
P0666
P0667
P0668
P0669
P0670
P0671
P0672
P0673
P0674
P0675
P0676
P0677
P0678
P0679
P0680
P0681
P0682
P0683
P0684
P0685
P0686
P0687
P0688
P0689
P0690
P0691
P0692
P0693
P0694
P0695
P0696
P0697
P0698
P0699
P0700
P0701
,
OWNER S MANUAL
OBDII Generic DTC Definitions
PCM/ECM/TCM Internal Temp. Sensor Circuit
PCM/ECM/TCM Internal Temp. Sensor Range/Performance
PCM/ECM/TCM Internal Temp. Sensor Circuit Low
PCM/ECM/TCM Internal Temp. Sensor Circuit Hig h
Glow Plug/Heater Module Control
Glow Plug/Heater Cylinder 1
Glow Plug/Heater Cylinder 2
Glow Plug/Heater Cylinder 3
Glow Plug/Heater Cylinder 4
Glow Plug/Heater Cylinder 5
Glow Plug/Heater Cylinder 6
Glow Plug/Heater Cylinder 7
Glow Plug/Heater Cylinder 8
Glow Plug/Heater Cylinder 9
Glow Plug/Heater Cylinder 10
Glow Plug/Heater Cylinder 11
Glow Plug/Heater Cylinder 12
Glow Plug/Heater Module Communication Problem
Glow Plug/Heater Communication Problem CKT Range/Performance
ECM/PCM Power Relay Control Circuit Open
ECM/PCM Power Relay Control Circuit Low
ECM/PCM Power Relay Control Circuit Hig h
ECM/PCM Power Relay Sense Circuit Open
ECM/PCM Power Relay Sense Circuit Low
ECM/PCM Power Relay Sense Circuit Hig h
Fan 1 Control Circuit Low
Fan 1 Control Circuit Hig h
Fan 2 Control Circuit Low
Fan 2 Control Circuit Hig h
Fan 3 Control Circuit Low
Fan 3 Control Circuit Hig h
Sensor C Reference Voltage Circuit Open
Sensor C Reference Voltage Circuit Low
Sensor C Reference Voltage Circuit Hig h
Trans Control Sys Malfunction
Trans Control Sys Range/Performance
OBD2 CODE READER
37
,
OWNER S MANUAL
P0702
P0703
P0704
P0705
P0706
P0707
P0708
P0709
P0710
P0711
P0712
P0713
P0714
P0715
P0716
P0717
P0718
P0719
P0720
P0721
P0722
P0723
P0724
P0725
P0726
P0727
P0728
P0729
P0730
P0731
P0732
P0733
P0734
P0735
P0736
P0737
38
CHECK
OBDII Generic DTC Definitions
Trans Control Sys Electrical
Brake Switch B Circuit Malfunction
Clutch Switch Input Circuit Malfunction
Trans Range Sensor Circuit Malfunction (PRNDL Input)
Trans Range Sensor CKT Range/Performance
Trans Range Sensor Circuit Low Input
Trans Range Sensor Circuit Hig h Input
Trans Range Sensor CKT Intermittent
Transmission Fluid Temperature Sensor Circuit Malfunction
Trans Fluid Temp Sensor A CKT Range/Performance
Trans Fluid Temp Sensor A Circuit Low Input
Trans Fluid Temp Sensor A Circuit Hig h Input
Trans Fluid Temp Sensor A CKT Intermittent
Input/Turbine Speed Sensor A Circuit Malfunction
Input/Turbine Speed Sensor A CKT Range/Performance
Input/Turbine Speed Sensor A Circuit No Signal
Input/Turbine Speed Sensor A CKT Intermittent
Brake Switch B Circuit Low Input
Output Speed Sensor Circuit Malfunction
Output Speed Sensor Circuit Range/Performance
Output Speed Sensor Circuit No Signal
Output Speed Sensor CKT Intermittent
Brake Switch B Circuit Hig h Input
Engine Speed Sensor Circuit Malfunction
Engine Speed Sensor CKT Range/Performance
Engine Speed Sensor Circuit No Signal
Engine Speed Sensor CKT Intermittent
Gear 6 Ratio Incorrect
Gear Ratio Incorrect
Gear 1 Ratio Incorrect
Gear 2 Ratio Incorrect
Gear 3 Ratio Incorrect
Gear 4 Ratio Incorrect
Gear 5 Ratio Incorrect
Reverse Ratio Incorrect
TCM Engine Speed Output Circuit
OBD2 CODE READER
CHECK
P0738
P0739
P0740
P0741
P0742
P0743
P0744
P0745
P0746
P0747
P0748
P0749
P0750
P0751
P0752
P0753
P0754
P0755
P0756
P0757
P0758
P0759
P0760
P0761
P0762
P0763
P0764
P0765
P0766
P0767
P0768
P0769
P0770
P0771
P0772
P0773
,
OWNER S MANUAL
OBDII Generic DTC Definitions
TCM Engine Speed Output Circuit Low
TCM Engine Speed Output Circuit Hig h
TCC Circuit Malfunction
Torque Converter CKT Performance Or Stuck Off
Torque Converter Circuit Stuck On
Torque Converter Circuit Electrical
Torque Converter CKT Intermittent
Pres Control Sol. A Circuit Malfunction
Pres Control Sol. A CKT Performance Or Stuck Off
Pres Control Sol. A Circuit Stuck On
Pres Control Sol. A Circuit Electrical
Pres Control Sol. A CKT Intermittent
Shift Solenoid A Malfunction
Shift Solenoid A CKT Performance Or Stuck Off
Shift Solenoid A Circuit Stuck On
Shift Solenoid A Circuit Electrical
Shift Solenoid A CKT Intermittent
Shift Solenoid B Malfunction
Shift Solenoid B CKT Performance Or Stuck Off
Shift Solenoid B Circuit Stuck On
Shift Solenoid B Circuit Electrical
Shift Solenoid B CKT Intermittent
Shift Solenoid C Malfunction
Shift Solenoid C CKT Performance Or Stuck Off
Shift Solenoid C Circuit Stuck On
Shift Solenoid C Circuit Electrical
Shift Solenoid C CKT Intermittent
Shift Solenoid D Malfunction
Shift Solenoid D CKT Performance Or Stuck Off
Shift Solenoid D Circuit Stuck On
Shift Solenoid D Circuit Electrical
Shift Solenoid D CKT Intermittent
Shift Solenoid E Malfunction
Shift Solenoid E CKT Performance Or Stuck Off
Shift Solenoid E Circuit Stuck On
Shift Solenoid E Circuit Electrical
OBD2 CODE READER
39
,
OWNER S MANUAL
P0774
P0775
P0776
P0777
P0778
P0779
P0780
P0781
P0782
P0783
P0784
P0785
P0786
P0787
P0788
P0789
P0790
P0791
P0792
P0793
P0794
P0795
P0796
P0797
P0798
P0799
P0800
P0801
P0802
P0803
P0804
P0805
P0806
P0807
P0808
P0809
40
CHECK
OBDII Generic DTC Definitions
Shift Solenoid E CKT Intermittent
Pres Ctrl Sol. B Circuit Malfunction
Pres Ctrl Sol. B CKT Performance Or Stuck Off
Pres Ctrl Sol. B Circuit Stuck On
Pres Ctrl Sol. B Circuit Electrical
Pres Ctrl Sol. B CKT Intermittent
Shift Malfunction
1-2 Shift Malfunction
2-3 Shift Malfunction
3-4 Shift Malfunction
4-5 Shift Malfunction
Shift/Timing Solenoid Malfunction
Shift/Timing Solenoid Range/Performance
Shift/Timing Solenoid Low
Shift/Timing Solenoid Hig h
Shift/Timing Solenoid Intermittent Ckt
Normal/Performance Switch Circuit Malfunction
Intermediate Shaft Speed Sensor A Circuit
Intermediate Shaft Speed Sensor A Circuit Range/Performance
Intermediate Shaft Speed Sensor A Circuit No Signal
Intermediate Shaft Speed Sensor A CKT Intermittent
Pres Ctrl Sol. C Malfunction
Pres Ctrl Sol. C CKT Performance Or Stuck Off
Pres Ctrl Sol. C Circuit Stuck On
Pres Ctrl Sol. C Circuit Electrical
Pres Ctrl Sol. C CKT Intermittent
Transfer Case Control System MIL Request
Reverse Inhibit Control Circuit Malfunction
Trans Control Sys MIL Request Circuit Open
1-4 Upshift (Ski p Shift) Solenoid Circuit Malfunction
1-4 Upshift (Ski p Shift) Lamp Circuit Malfunction
Clutch Position Sensor Circuit Malfunction
Clutch Position Sensor Circuit Range/Performance
Clutch Position Sensor Circuit Low
Clutch Position Sensor Circuit Hig h
Clutch Position Sensor Circuit Intermittent Ckt
OBD2 CODE READER
CHECK
P0810
P0811
P0812
P0813
P0814
P0815
P0816
P0817
P0818
P0819
P0820
P0821
P0822
P0823
P0824
P0825
P0826
P0827
P0828
P0829
P0830
P0831
P0832
P0833
P0834
P0835
P0836
P0837
P0838
P0839
P0840
P0841
P0842
P0843
P0844
P0845
,
OWNER S MANUAL
OBDII Generic DTC Definitions
Clutch Position Control Malfunction
Clutch Sli ppage Excessive
Reverse Input Circuit Malfunction
Reverse Output Circuit Malfunction
Trans Range Display Circuit Malfunction
Upshift Switch Circuit Malfunction
Downshift Switch Circuit Malfunction
Starter Disable Circuit
Driveline Disconnect. Switch Input
Up/Down Shift SW Transmission Range Correlation
Gear Lever X-Y Sensor Circuit
Gear Lever X Sensor Circuit
Gear Lever Y Sensor Circuit
Gear Lever X Sensor Circuit Intermittent Ckt
Gear Lever Y Sensor Circuit Intermittent Ckt
Gear Lever Push/Pull Switch (Shift Antici pate)
Upshift Switch Downshift Switch Circuit
Upshift Switch Downshift Switch Circuit Low
Upshift Switch Downshift Switch Circuit Hig h
5-6 Shift
Clutch Position Switch A Circuit Malfunction
Clutch Position Switch A Circuit Low
Clutch Position Switch A Circuit Hig h
Clutch Position Switch B Circuit Malfunction
Clutch Position Switch B Circuit Low
Clutch Position Switch B Circuit Hig h
4 Wheel Drive Switch Circuit Malfunction
4 Wheel Drive Switch CKT Range/Performance
4 Wheel Drive Switch Circuit Low
4 Wheel Drive Switch Circuit Hig h
Trans Fluid Press Sensor/Switch A Circuit Malfunction
Trans Fluid Press Sensor/Switch A CKT Range/Performance
Trans Fluid Press Sensor/Switch A Circuit Low
Trans Fluid Press Sensor/Switch A Circuit Hig h
Trans Fluid Press Sensor/Switch A CKT Intermittent
Trans Fluid Press Sensor/Switch B Circuit Malfunction
OBD2 CODE READER
41
,
OWNER S MANUAL
P0846
P0847
P0848
P0849
P0850
P0851
P0852
P0853
P0854
P0855
P0856
P0857
P0858
P0859
P0860
P0861
P0862
P0863
P0864
P0865
P0866
P0867
P0868
P0869
P0870
P0871
P0872
P0873
P0874
P0875
P0876
P0877
P0878
P0879
P0880
P0881
42
CHECK
OBDII Generic DTC Definitions
Trans Fluid Press Sensor/Switch B CKT Range/Performance
Trans Fluid Press Sensor/Switch B Circuit Low
Trans Fluid Press Sensor/Switch B Circuit Hig h
Trans Fluid Press Sensor/Switch B CKT Intermittent
Park/Neutral Switch Input Circuit
Park/Neutral Switch Circuit Low Input
Park/Neutral Switch Circuit Hig h Input
Drive Switch Input Circuit
Drive Switch Circuit Low Input
Drive Switch Circuit Hig h Input
Traction Control Input Signal
Traction Control Input Signal Range/Performance
Traction Control Input Signal Low
Traction Control Input Signal Hig h
Gear Shift Module Communications Circuit
Gear Shift Module Communications Circuit Low
Gear Shift Module Communications Circuit Hig h
TCM Communications Circuit
TCM Communications CKT Range/Performance
TCM Communications Circuit Low
TCM Communications Circuit Hig h
Trans Fluid Press
Trans Fluid Press Low
Trans Fluid Press Hig h
Trans Fluid Press Sensor/Switch C Circuit
Trans Fluid Press Sensor/Switch C CKT Range/Performance
Trans Fluid Press Sensor/Switch C Circuit Low
Trans Fluid Press Sensor/Switch C Circuit Hig h
Trans Fluid Press Sensor/Switch C CKT Intermittent
Trans Fluid Press Sensor/Switch D Circuit
Trans Fluid Press Sensor/Switch D CKT Range/Performance
Trans Fluid Press Sensor/Switch D Circuit Low
Trans Fluid Press Sensor/Switch D Circuit Hig h
Trans Fluid Press Sensor/Switch D CKT Intermittent
TCM Power Input Signal
TCM Power Input Signal Range/Performance
OBD2 CODE READER
CHECK
P0882
P0883
P0884
P0885
P0886
P0887
P0888
P0889
P0890
P0891
P0892
P0893
P0894
P0895
P0896
P0897
P0898
P0899
P0900
P0901
P0902
P0903
P0904
P0905
P0906
P0907
P0908
P0909
P0910
P0911
P0912
P0913
P0914
P0915
P0916
P0917
,
OWNER S MANUAL
OBDII Generic DTC Definitions
TCM Power Input Signal Low
TCM Power Input Signal Hig h
TCM Power Input Signal CKT Intermittent
TCM Power Relay Control Circuit Open
TCM Power Relay Control Circuit Low
TCM Power Relay Control Circuit Hig h
TCM Power Relay Sense Circuit
TCM Power Relay Sense CKT Range/Performance
TCM Power Relay Sense Circuit Low
TCM Power Relay Sense Circuit Hig h
TCM Power Relay Sense CKT Intermittent
Multi ple Gears Engaged
Transmission Comp. Sli pping
Shift Time Too Short
Shift Time Too Long
Transmission Fluid Deteriorated
Transmission Ctrl. MIL Request Circuit Low
Transmission Ctrl. MIL Request Circuit Hig h
Clutch Actuator Circuit Open
Clutch Actuator CKT Range/Performance
Clutch Actuator Circuit Low
Clutch Actuator Circuit Hig h
Gate Select Position Circuit
Gate Select Position CKT Range/Performance
Gate Select Position Circuit Low
Gate Select Position Circuit Hig h
Gate Select Position CKT Intermittent
Gate Select Control Error
Gate Select Actuator Circuit Open
Gate Select Actuator CKT Range/Performance
Gate Select Actuator Circuit Low
Gate Select Actuator Circuit Hig h
Gear Shift Position Circuit
Gear Shift Position CKT Range/Performance
Gear Shift Position Circuit Low
Gear Shift Position Circuit Hig h
OBD2 CODE READER
43
,
OWNER S MANUAL
P0918
P0919
P0920
P0921
P0922
P0923
P0924
P0925
P0926
P0927
P0928
P0929
P0930
P0931
P0932
P0933
P0934
P0935
P0936
P0937
P0938
P0939
P0940
P0941
P0942
P0943
P0944
P0945
P0946
P0947
P0948
P0949
P0950
P0951
P0952
P0953
44
CHECK
OBDII Generic DTC Definitions
Gear Shift Position CKT Intermittent
Gear Shift Position Control Error
Gear Shift Forward Actuator Circuit Open
Gear Shift Forward Actuator CKT Range/Performance
Gear Shift Forward Actuator Circuit Low
Gear Shift Forward Actuator Circuit Hig h
Gear Shift Reverse Actuator Circuit Open
Gear Shift Reverse Actuator CKT Range/Performance
Gear Shift Reverse Actuator Circuit Low
Gear Shift Reverse Actuator Circuit Hig h
Gear Shift Lock Solenoid Ctrl Circuit Open
Gear Shift Lock Solenoid Ctrl CKT Range/Performance
Gear Shift Lock Solenoid Ctrl Circuit Low
Gear Shift Lock Solenoid Ctrl Circuit Hig h
Hydraulic Pressure Sensor Circuit
Hydraulic Pressure Sensor CKT Range/Performance
Hydraulic Pressure Sensor Circuit Low
Hydraulic Pressure Sensor Circuit Hig h
Hydraulic Pressure Sensor CKT Intermittent
Hydraulic Oil Temp Sensor Circuit
Hydraulic Oil Temp Sensor CKT Range/Performance
Hydraulic Oil Temp Sensor Circuit Low
Hydraulic Oil Temp Sensor Circuit Hig h
Hydraulic Oil Temp Sensor CKT Intermittent
Hyd. Pressure Unit
Hyd. Pressure Unit Cycling Too Short
Hyd. Pressure Unit Loss of Pressure
Hyd. Pump Relay Circuit Open
Hyd. Pump Relay CKT Range/Performance
Hyd. Pump Relay Circuit Low
Hyd. Pump Relay Circuit Hig h
Auto Shift Adaptive Learning Not Complete
Auto Shift Manual Control Circuit
Auto Shift Manual Control CKT Range/Performance
Auto Shift Manual Control Circuit Low
Auto Shift Manual Control Circuit Hig h
OBD2 CODE READER
CHECK
P0955
P0956
P0957
P0958
P0959
P0960
P0961
P0962
P0963
P0964
P0965
P0966
P0967
P0968
P0969
P0970
P0971
P0972
P0973
P0974
P0975
P0976
P0977
P0978
P0979
P0980
P0981
P0982
P0983
P0984
P0985
P0986
P0987
P0988
P0989
P0990
,
OWNER S MANUAL
OBDII Generic DTC Definitions
Auto Shift Manual Mode Circuit
Auto Shift Manual Mode CKT Range/Performance
Auto Shift Manual Mode Circuit Low
Auto Shift Manual Mode Circuit Hig h
Auto Shift Manual Mode CKT Intermittent
Pressure Control Solenoid A Control Circuit Open
Pressure Control Solenoid A Control CKT Range/Performance
Pressure Control Solenoid A Control Circuit Low
Pressure Control Solenoid A Control Circuit Hig h
Pressure Control Solenoid B Control Circuit Open
Pressure Control Solenoid B Control CKT Range/Performance
Pressure Control Solenoid B Control Circuit Low
Pressure Control Solenoid B Control Circuit Hig h
Pressure Control Solenoid C Control Circuit Open
Pressure Control Solenoid C Control CKT Range/Performance
Pressure Control Solenoid C Control Circuit Low
Pressure Control Solenoid C Control Circuit Hig h
Shift Solenoid A Control CKT Range/Performance
Shift Solenoid A Control Circuit Low
Shift Solenoid A Control Circuit Hig h
Shift Solenoid B Control CKT Range/Performance
Shift Solenoid B Control Circuit Low
Shift Solenoid B Control Circuit Hig h
Shift Solenoid C Control CKT Range/Performance
Shift Solenoid C Control Circuit Low
Shift Solenoid C Control Circuit Hig h
Shift Solenoid D Control CKT Range/Performance
Shift Solenoid D Control Circuit Low
Shift Solenoid D Control Circuit Hig h
Shift Solenoid E Control CKT Range/Performance
Shift Solenoid E Control Circuit Low
Shift Solenoid E Control Circuit Hig h
Trans Fluid Press Sensor/Switch E Circuit
Trans Fluid Press Sensor/Switch E CKT Range/Performance
Trans Fluid Press Sensor/Switch E Circuit Low
Trans Fluid Press Sensor/Switch E Circuit Hig h
OBD2 CODE READER
45
,
OWNER S MANUAL
P0991
P0992
P0993
P0994
P0995
P0996
P0997
P0998
P0999
46
CHECK
OBDII Generic DTC Definitions
Trans Fluid Press Sensor/Switch E CKT Intermittent
Trans Fluid Press Sensor/Switch F Circuit
Trans Fluid Press Sensor/Switch F CKT Range/Performance
Trans Fluid Press Sensor/Switch F Circuit Low
Trans Fluid Press Sensor/Switch F Circuit Hig h
Trans Fluid Press Sensor/Switch F CKT Intermittent
Shift Solenoid F Control CKT Range/Performance
Shift Solenoid F Control Circuit Low
Shift Solenoid F Control Circuit Hig h
OBD2 CODE READER
CHECK
,
OWNER S MANUAL
5.2 Part Of OBD2 Manufacturer Specific DTC Definitions
VEHICLE MANUFACTURER: CHRYSLER
CHRYSLER (P1016-P1043)
CODE
P1000
P1000
P1004
P1005
P1006
P1007
P1008
P1009
P1012
P1013
P1014
P1015
P1016
P1017
P1018
P1019
P1021
P1022
P1024
P1025
P1026
P1027
P1028
P1029
P1030
P1031
P1032
P1033
P1037
P1038
P1039
DEFINITION
Ignition Circ Low
Ignition Circ Low
ECU Battery Feed & Power Grounds
Sys Ground Circ
EGR/EVAP Solenoid Circ Low
EGR/EVAP Solenoid Circ Hi
Power Steering Circ Low
Power Steering Circ Hi
MPA Circ Low
MPA Circ Hi
Fuel Pump Circ Low
Fuel Pump Circ Hi
Charge Air Temp Circ
Charge Air Temp Circ Hi
Serial Data Circ
Power Latch Not Set
Engine Failed To Start Due To Mechanical,Fuel or Ignition Conditions
Starter Relay Circ Low
ECU Start Circ Low
WOT Circ Low
WOT Circ Hi
ECU Sees Wide Open Throttle
ECU Does Not See Wide Open Throttle
ISA Closed Throttle Circ Low
ISA Closed Throttle Circ Hi
ECU Sees Closed Throttle
ECU Does Not See Closed Throttle
ISA Circs
TP Sens Circ Reads Low
Park/Neutral Line Hi
Park/Neutral Line Low
OBD2 CODE READER
47
,
OWNER S MANUAL
CHECK
CODE DEFINITION
P1040
Latched B+ Line Low
P1041
Latched B+ Line Hi
P1042
No Latched B+ 1/2 Volt Drop
P1043
Shift Lamp Circ Grounded
P1044
D2–1 Circ Low (A/T) or Upshift Lamp Circ (M/T) or Shift Lamp Circ Hi
P1045
Shift Lamp Circ
P1047
Wrong ECU
P1048
M/T Vehicle Configuration
P1049
A/T Vehicle Configuration
P1050
Idle RPM Low
P1051
Idle RPM Hi
P1052
MAP Sens Out Of Limits
P1053
Change In MAP Reading Out Of Limits
P1054
Coolant Sens & 5V Supply for TP Sens/MAP Circs Low
P1055
Coolant Sens Circ Hi
P1056
Inactive Coolant Temp Sens
P1059
A/C Request Circ Low
P1060
A/C Request Circ Hi
P1061
A/C Select Circ Low
P1062
A/C Select Circ Hi
P1063
A/C Clutch Circ Low
P1064
A/C Clutch Circ Hi & Power Steering Input
P1068
Latch Relay Circ Hi
P1069
No Tach
P1074
ECU Does Not See Speed Sens
P1105
Open or shorted condition detected in the baro read solenoid control
circuit
P1106
MAP Sens Circ Interm Hi Voltage
P1107
MAP Sens Circ Interm Low Voltage
P1110
Decreased Engine Perf Due To Hi Intake Air Temp
P1111
IAT Sens Circ Interm Hi Voltage
P1112
IAT Sens Circ Interm Low Voltage
P1114
ECT Sens Circ Interm Low Voltage
P1115
ECT Sens Circ Interm Hi Voltage
P1121
TPS Circ Interm Hi Voltage
P1122
TPS Circ Interm Low Voltage
48
OBD2 CODE READER
CHECK
CODE
P1125
P1133
P1134
P1153
P1154
P1180
P1191
P1192
P1193
P1194
P1195
P1196
P1197
P1198
P1199
P1214
P1216
P1217
P1218
P1243
P1271
P1272
P1273
P1275
P1277
P1278
P1280
P1281
P1282
P1283
P1284
P1285
P1286
P1287
,
OWNER S MANUAL
DEFINITION
Accelerator Pedal Pos Sys
HO2S Insufficient Switching Bank1 Sens1
HO2S Insufficient Transition Time Ratio Bank1 Sens1
HO2S Insufficient Switching Bank2 Sens1
HO2S Insufficient Transition Time Ratio Bank2 Sens 1
Decreased Engine Perf Due To Hi Inj Pump Fuel Temp
Intake Air Duct Leak
Inlet Air Temp Sens Voltage Low
Inlet Air Temp Voltage Hi
02 Heater Perf
1/1 02 Sens Slow During Catalyst Monitor
2/1 02 Sens Slow During Catalyst Monitor
1/2 02 Sens Slow During Catalyst Monitor
Radiator Temp Sens Volts Too Hi
Radiator Temp Sens Volts Too Low
Inj Pump Timing Offset
Fuel Solenoid Response Time Too Short
Fuel Solenoid Response Time Too Long
Inj Pump Calibration Circ
Open or shorted condition detected in the turbocharger surge
valvesolenoid control
Accelerator Pedal Pos Sens1-2 Correlation
Accelerator Pedal Pos Sens2-3 Correlation
Accelerator Pedal Pos Sens1-3 Correlation
Accelerator Pedal Pos Sens1 Circ
Accelerator Pedal Pos Sens1 Low Voltage
Accelerator Pedal Pos Sens1 Hi Voltage
Accelerator Pedal Pos Sens2 Circ
Engine is Cold Too Long
Accelerator Pedal Pos Sens2 Low Voltage or Fuel Pump Relay Ctrl Circ
Accelerator Pedal Pos Sens2 Hi Voltage or Idle Select Signal Invalid
Fuel Inj Pump Battery Voltage Out Of Range
Accelerator Pedal Pos Sens3 Circ or Fuel Inj Pump Ctrller Always On
Accelerator Pos Sens Supply Voltage Too Hi
Accelerator Pedal Pos Sens3 Low Voltage or Fuel Inj Pump
CtrlSupply Voltage Low
OBD2 CODE READER
49
,
OWNER S MANUAL
CODE
P1288
P1289
P1290
P1291
P1292
P1293
P1294
P1295
P1296
P1297
P1298
P1299
P1336
P1345
P1351
P1361
P1380
P1381
P1388
P1389
P1390
P1391
P1398
P1399
P1403
P1404
P1406
P1409
P1415
P1416
P1441
P1475
P1476
P1477
P1478
50
CHECK
DEFINITION
Accelerator Pedal Pos Sens3 Hi Voltage or Intake Manif Short
Runner Solenoid Circ
Manif Tune Valve Solenoid Circ
CNG Fuel Sys Press Too Hi
No Temp Rise Seen From Intake Heaters
CNG Press Sens Voltage Too Hi
CNG Press Sens Voltage Too Low
Target Idle Not Reached
No 5Vs to Throttle Pos Sens
No 5Vs to MAP Sens
No Change in MAP from Start To Run
Lean Operation at Wide Open Throttle
Vacuum Leak Found (IAC Fully Seated)
Crank Pos Sys Variation Not Learned
Crank Pos/Camshaft Pos Correlation
Ignition Ctrl Circ Hi Voltage
Ignition Ctrl Circ Low Voltage
Electronic Brake Ctrl Roug h Road Data Unusable
Misfire Detected-No Electronic Brake Ctrl Data
Auto Shutdown Relay Ctrl Circ
No ASD Relay Output Voltage at PCM
Timing Belt Ski pped 1 Tooth or More
Interm Loss of CMP or CKP
Misfire Adaptive Numerator at Limit
Wait to Start Lamp Circ
No 5Vs to EGR Sens
EGR Valve Closed Pintle Pos
EGR Valve Pos
EGR Valve Sys leak
AIR Sys Bank1
AIR Sys Bank1
Evap Emissions Flow During Non-Purge
Auxiliary 5V Supply Voltage Hi
Too Little Sec Air
Too Much Sec Air
Battery Temp Sens Volts Out of Limit
OBD2 CODE READER
CHECK
,
OWNER S MANUAL
CODE DEFINITION
P1479
Trans Fan Relay Circ
P1480
PCV Solenoid Circ
P1481
EATX Misfire RPM Signal out of Range
P1482
Catalyst Temp Sens Circ Shorted Low
P1483
Catalyst Temp Sens Circ Shorted Hi
P1484
Catalytic Conv Overheat Detected
P1485
Air Inj Solenoid Circ
P1486
Eva Leak Monitor Pinched Hose Found
P1487
Hi Speed Radiator Fan CTRL Relay Circ
P1488
Auxiliary 5V Supply Output Too Low
P1489
Hi Speed Fan CTRL Relay Circ
P1490
Low Speed Fan CTRL Relay Circ
P1491
Radiator Fan Ctrl Relay Circ
P1492
Ambient/Battery Temp Sens Volts Too Hi
P1493
Ambient/Battery Temp Sens Volts Too Low
P1494
Leak Detection Pump Switch or Mechanical Fault
P1495
Leak Detection Pump Solenoid Circ
P1496
5V Supply,Output Too Low
P1498
Hi Speed Radiator Fan Ground CTRL Relay Circ
P1499
Open or shorted condition detected in the hydraulic cooling fan
solenoid control
P1508
IAC Sys Low RPM
P1509
IAC Sys Hi RPM
P1594
Charging Sys Voltage Too Hi
P1595
Speed Ctrl Solenoid Circs
P1596
Speed Ctrl Switch Always Hi
P1597
Speed Ctrl Switch Always Low
P1598
A/C Press Sens Volts Too Hi
P1599
A/C Press Sens Volts Too Low
P1602
PCM Not Programmed
P1621
PCM Memory Perf or Write
P1626
Vehicle Theft Sys Ctrl Loss of Data
P1627
A/D Perf
P1630
Vehicle Theft Sys PCM in Learn Mode
P1631
Vehicle Theft Sys Improper Password
P1635
5V Ref Circ
OBD2 CODE READER
51
,
OWNER S MANUAL
CHECK
CODE DEFINITION
P1639
5V Ref Circ
P1641
MIL Ctrl Circ
P1643
Wait To Start Lamp Ctrl Circ
P1646
5V Ref (C) Circ
P1652
J1850 Comms Bus
P1653
EGR Vent Solenoid Ctrl Circ
P1654
Service Throttle Soon Lamp Ctrl Circ
P1655
EGR Solenoid Ctrl Circ
P1656
Wastegate Solenoid Ctrl Circ
P1680
Clutch Released Switch Circ
P1681
No I/P Cluster CCD/J1850 Messages Received
P1682
Charging Sys Voltage Too Low
P1683
Speed Ctrl Power Relay; or S/C 12v Driver CKT
P1684
Battery Disconnected in the last 50 Starts
P1685
Skim Invalid Key
P1686
No SKIM BUS Messages Received
P1687
No Cluster BUS Message
P1688
Internal Fuel Inj Pump Ctrller Failure
P1689
No Comm between ECM & Inj Pump Mod
P1690
CKP Sens Does Not Agree with ECM CKP Sens
P1691
Fuel Sys ESS RPM Error
P1692
DTC Set In ECM
P1693
DTC Detected in Companion JTEC Mod
P1694
No BUS Message Received from ECM Mod
P1695
No CCD/J1850 Messages from the Body Ctrl Mod.
P1696
PCM Failure EEPROM Write Denied
P1697
PCM Failure SRI Mile Not Stored
P1698
No CCD/J1850 Message From TCM/PCM
P1699
No CCD/J1850 Messages received from the Climate Control
Module(CCM)
P1719
Ski p Shift Solenoid Circ
P1740
TCC or O/D Solenoid Perf
P1756
Gov Press Not Equal to Target @ not15-20 PSI
P1757
Gov Press above 3 PSI in gear with 0 MPH
P1762
Gov Press Sens Offset Volts Too Low or Hi
P1763
Governor Press Sens Volts Too Hi
52
OBD2 CODE READER
CHECK
CODE
P1764
P1765
P1830
P1899
P1100
P1120
P1121
P1125
P1126
P1127
P1128
P1129
P1130
P1133
P1135
P1150
P1153
P1155
P1200
P1300
P1305
P1310
P1315
P1320
P1320
P1330
P1335
P1340
,
OWNER S MANUAL
DEFINITION
Governor Press Sens Volts Too Low
Trans 12 Volt Supply Relay CTRL Circ
Open or shorted condition detected in the clutch pedal switch
over-ride relay control
P/N Switch Stuck in Park or in Gear
BARO Sensor Circuit malfunction
Accelerator Pedal Position Sensor Circuit Malfunction
Accelerator Pedal Position Sensor Range/Performance Problem
Throttle Control Motor Circuit Malfunction
Magnetic Clutch Circuit Malfunction
ETCS Actuator Power Source Circuit Malfunction
Throttle Control Motor Lock Malfunction
Electric Throttle Control System Malfunction
Air–Fuel Sensor Circuit Range/Performance
Air–Fuel Sensor Circuit Response Malfunction
Air–Fuel Sensor Heater Circuit Response Malfunction
A./F Sensor Circuit Range/Performance Malfunction
A./F Sensor Circuit Response Malfunction
A./F Sensor Heater Circuit Malfunction
Fuel Pump Relay Circuit Malfunction
Igniter Circuit Malfunction No. 1
Igniter Circuit Malfunction No. 2 (1998-2000 Land Cruiser,2000
Celica &Tundra)
Igniter Circuit Malfunction No. 2 (Except 1998-2000 Land Cruiser,
2000Celica & Tundra),or Igniter Circuit Malfunction No. 3 (19982000 Land Cruiser,2000 Celica & Tundra)
Igniter Circuit Malfunction No. 4 (1998-2000 Land Cruiser,2000
Celica &Tundra)
Igniter Circuit Malfunction No. 5 (1998-2000 Land Cruiser & 2000
Tundra)
Igniter Circuit Malfunction No. 5 (1998-2000 Land Cruiser & 2000
Tundra)
Igniter Circuit Malfunction No. 7 (1998-2000 Land Cruiser & 2000
Tundra)
No CKP Sensor Signal Engine Running
Igniter Circuit Malfunction No. 8 (1998-2000 Land Cruiser & 2000
Tundra)
OBD2 CODE READER
53
,
OWNER S MANUAL
CODE
P1345
P1346
P1349
P1350
P1351
P1354
P1400
P1401
P1405
P1406
P1410
P1411
P1500
P1510
P1511
P1512
P1520
P1565
P1600
P1605
P1630
P1633
P1645
P1652
P1656
P1658
P1661
P1662
P1663
P1690
P1692
P1693
P1780
54
CHECK
DEFINITION
VVT Sensor/Camshaft Position Sensor Circuit Malfunction Bank 1
VVT Sensor/Camshaft Position Sensor Circuit Range/Performance
Problem(Bank 1)
VVT System Malfunction Bank 1
VVT Sensor/Camshaft Position Sensor Circuit Malfunction Bank 2
VVT Sensor/Camshaft Position Sensor Circuit Range/Performance
Problem Bank 2
VVT System Malfunction Bank 2
Sub-Throttle Position Sensor Malfunction
Sub-Throttle Position Sensor Range/Performance Problem
Turbo Pressure Sensor Circuit Malfunction
Turbo Pressure Sensor Range/Performance Problem
EGR Valve Position Sensor Circuit Malfunction
EGR Valve Position Sensor Circuit Range/Performance
Starter Signal Circuit Malfunction
Boost Pressure Control Circuit Malfunction
Boost Pressure Low Malfunction
Boost Pressure Hig h Malfunction
Stop Lamp Switch Signal Malfunction
Cruise Control Main Switch Circuit Malfunction
ECM BATT Malfunction
Knock Control CPU Malfunction
Traction Control System Malfunction
ECM Malfunction ECTS Circuit
Body ECU Malfunction
IACV Control Circuit Malfunction
OCV Circuit Malfunction Bank 1
Waste Gate Valve Control Circuit Malfunction
EGR Circuit Malfunction
EGR By-Pass Valve Control Circuit Malfunction
OCV Circuit Malfunction Bank 2
OCV Circuit Malfunction
OCV Open Malfunction
OCV Closed Malfunction
PNP Switch Malfunction
OBD2 CODE READER
CHECK
,
OWNER S MANUAL
6. WARRANTY AND SERVICE
6.1 Limited One Year Warranty
We warrants to its customers that this product will be free from all defects
in materials and workmanshi p for a period of one (1) year from the date
of the original purchase, subject to the following terms and conditions:
1. The sole responsibility of us under the Warranty is limited to either the
repair or, at the option of us, replacement of the Scan Tool at no charge
with Proof of Purchase. The sales recei pt may be used for this purpose.
2. This warranty does not apply to damages caused by improper use,
accident, flood, lig htning, or if the product was altered or repaired by
anyone other than the Manufacturer's Service Center.
3. We shall not be liable for any incidental or consequential damages
arising from the use, misuse, or mounting of the Scan Tool. Some states
do not allow limitations on how long an implied warranty lasts, so the
above limitations may not apply to you.
6.2 Service Procedures
For technical support, please contact your local store or distributor. If it
becomes necessary to return the code reader for repair, contact your
local distributor for more information.
OBD2 CODE READER
55
OWNER’S
MANUAL
FASTER &
EASIER
FOR 1996
AND
NEWER
OBD II
VEHICLES
T40
DIGITAL
OBD2/CAN
CODE READER
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement