E6/E60 Instructions for Use
Table of contents
Your E6/E60
Control elements
4
Important information
6
Proper use ...................................................................................................................................................... 6
For your safety ............................................................................................................................................... 6
1 Preparing and using for the first time
10
JURA on the Internet ....................................................................................................................................10
Setting up the machine ..............................................................................................................................10
Filling the bean container ...........................................................................................................................10
Determining the water hardness ..............................................................................................................10
First-time use .................................................................................................................................................11
Connecting milk ...........................................................................................................................................14
2 Preparation
15
Espresso and coffee .....................................................................................................................................15
Two espressi and two coffees.....................................................................................................................16
Cappuccino....................................................................................................................................................16
Milk foam.......................................................................................................................................................17
Permanently setting the amount of water for the cup size .................................................................17
Adjusting the grinder ..................................................................................................................................18
Hot water .......................................................................................................................................................18
3 Daily operation
19
Filling the water tank ...................................................................................................................................19
Switching on the machine ..........................................................................................................................19
Daily maintenance .......................................................................................................................................19
Regular maintenance .................................................................................................................................20
Switching off the machine.........................................................................................................................20
4 Permanent settings in programming mode
22
Adjusting the product settings ................................................................................................................. 22
Automatic switch-off .................................................................................................................................. 23
Setting the water hardness .......................................................................................................................24
Unit for amount of water ...........................................................................................................................24
Language ......................................................................................................................................................25
5 Maintenance
26
Rinsing the machine ...................................................................................................................................26
Rinsing the fine foam frother....................................................................................................................26
Cleaning the fine foam frother ................................................................................................................. 27
Dismantling and rinsing the fine foam frother......................................................................................28
Inserting the filter .......................................................................................................................................28
Changing the filter ......................................................................................................................................29
Cleaning the machine ................................................................................................................................30
Descaling the machine ...............................................................................................................................31
Cleaning the bean container ..................................................................................................................... 33
Descaling the water tank ...........................................................................................................................34
2
Table of contents
6 Display messages
35
7 Troubleshooting
36
8 Transport and environmentally friendly disposal
38
Transport / Emptying the system.............................................................................................................38
Disposal.........................................................................................................................................................38
9 Technical data
39
10 Index
40
11 JURA contact details / Legal information
44
Symbol description
Warnings
J WARNING Always take note of any information marked with the words CAUTION or
J CAUTION WARNING and a warning sign. The signal word WARNING draws your attention
to potential serious injury, and the signal word CAUTION to potential minor
injury.
CAUTION
CAUTION draws your attention to potential damage to the machine.
Symbols used
Prompt to take action. This symbol means that you are being prompted to perform
T
some action.
Information and tips to make it even easier to use your JURA.
E
‘Coffee’
Display
3
Control elements
Control elements
9
1
10
2
11
3
4
5
12
6
13
7
8
1
2
3
4
5
6
7
8
4
14
Cover of filler funnel for cleaning tablet
Filler funnel for cleaning tablet
Bean container with aroma preservation
cover
Water tank cover
Water tank
Mains cable (back of the machine)
Coffee grounds container
Drip tray
9
10
11
12
13
14
Cover cap for grinder adjustment switch
Grinder adjustment switch
On/Off button Q
Fine foam frother
Height-adjustable coffee spout
Cup grille
Control elements
1
2
3
1
2
Display
Multi-function buttons (button function
depends on what is shown in the display)
3
Switch for hot water and steam
preparation
5
Important information
Important information
Proper use
The machine is designed and intended for private
domestic use. It should only be used for coffee
preparation and to heat milk and water. Use for
any other purpose will be deemed improper. JURA
Elektroapparate AG cannot accept any responsibility for the consequences of improper use.
Before using the machine read these instructions
for use thoroughly and completely and comply
with the instructions they contain. A warranty service is not applicable for damage or defects caused
by non-compliance with the instructions for use.
Keep these instructions for use close to the machine
and pass them on to the next user.
For your safety
J
6
Please carefully read and observe the important
safety information set out below.
To avoid danger of potentially fatal electric shock:
U Never use a machine which is damaged or has
a defective mains cable.
U In the event of signs of damage, for example if
there is a smell of burning, unplug the machine
immediately from the mains supply and contact JURA service.
U For models with a permanently connected
mains cable: If the mains cable of this machine
is damaged, it must be repaired either directly
by JURA or by an authorised JURA service
centre.
U For models with a disconnectable mains cable:
If the mains cable of this machine is damaged
it must be replaced with a special mains cable,
Important information
U
U
U
U
which is available directly from JURA or from
authorised JURA service centres.
Make sure that the JURA and the mains cable
are not located close to hot surfaces.
Be careful to ensure that the mains cable is not
trapped and does not rub against sharp edges.
Never open and repair the machine yourself.
Do not modify the machine in any way that is
not described in these instructions for use. The
machine contains live parts. If opened, there is
a danger of potentially fatal injury. Repairs
may only be carried out by authorised JURA
service centres, using original spare parts and
accessories.
To completely and safely disconnect the
machine from the power supply, first switch
off the JURA using the On/Off button. Only
then should you remove the mains plug from
the power socket.
There is a risk of scalds or burns on the spouts and
fine foam frother:
U Place the machine out of the reach of children.
U Do not touch any hot parts. Use the handles
provided.
U Be careful to ensure that the fine foam frother
is correctly installed and clean. If incorrectly
fitted or if it becomes blocked, the fine foam
frother or its parts might come off.
A defective machine is not safe and could cause
injury or fire. To avoid damage and any associated
risk of injury or fire:
U Never allow the mains cable to loosely hang
down. The mains cable could pose a tripping
hazard or become damaged.
7
Important information
U
U
U
U
U
U
U
U
U
U
U
U
U
8
Protect the JURA from environmental influences such as rain, frost and direct sunlight.
Do not immerse the JURA, mains cable or connections in water.
Do not put the JURA or any individual parts in
the dishwasher.
Before cleaning, switch your JURA off with the
On/Off button. Always wipe the JURA with a
damp cloth rather than a wet one, and protect
it from prolonged exposure to water splash.
Only connect the machine to the mains voltage in accordance with the information on the
rating plate. The rating plate is located on the
underside of your JURA. Further technical data
is provided in these instructions for use (see
Chapter 9 ‘Technical data’).
Connect the JURA directly to a domestic power
socket. Using multi-socket adapters or extension cords may cause overheating.
Please only use original JURA maintenance
products. Use of products that are not explicitly recommended by JURA could damage the
JURA.
Do not use any coffee beans treated with additives or caramelised coffee beans.
Only fill the water tank with fresh, cold water.
Switch the machine off with the On/Off button
if you are going to be absent for a longer
period of time and remove the mains plug
from the power socket.
Children may not clean or service the machine
unless supervised by a responsible person.
Do not allow children to play with the machine.
Keep children under the age of 8 away from
the machine, or supervise them constantly.
Important information
U
Children aged 8 and over may only operate
the machine without supervision if they have
been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use.
People, including children, who
U do not have the physical, sensory or mental
capabilities to use the machine safely or
U are inexperienced or lack knowledge in how to
use the machine safely
must be supervised by a responsible person when
using it, or must be instructed in how to use it correctly.
Safety when handling the CLARIS Smart filter cartridge:
U Filter cartridges should be kept out of the
reach of children.
U Store filter cartridges in a dry place in the
sealed packaging.
U Protect cartridges from heat and direct
sunlight.
U Do not use damaged filter cartridges.
U Do not open filter cartridges.
9
1 Preparing and using for the first time
1 Preparing and using for the first time
JURA on the Internet
Visit us on the Internet. You can download short operating instructions for your machine from the JURA website (www.jura.com). You
will also find interesting and up-to-date information on your JURA
and on every aspect of coffee.
Setting up the machine
When setting up your JURA, please note the following:
Place the JURA on a horizontal surface that is not sensitive to
water.
Choose a spot for your JURA which protects the machine
against overheating. Ensure that the ventilation slots are not
covered.
U
U
Filling the bean container
CAUTION
Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinder.
T Only use roasted, untreated coffee beans to fill the bean container.
T Remove the aroma preservation cover.
T Remove any dirt or foreign objects from inside the bean
container.
T Fill the bean container with coffee beans and close the
aroma preservation cover.
Determining the water
hardness
10
When you use the machine for the first time, you must set the water
hardness. If you do not know the hardness of your water, you can
find this out first. Use the Aquadur® test strips supplied with the
machine.
T Hold the test strip briefly (for 1 second) under flowing water.
Shake off the water.
T Wait for about 1 minute.
1 Preparing and using for the first time
T You will then be able to read the degree of water hardness
from the discolouration of the Aquadur® test strip and the
description on the packaging.
First-time use
When using the machine for the first time, you can choose whether
you want to operate JURA with or without the CLARIS Smart filter
cartridge. If the water hardness is 10 °dH or more, we recommend
using the filter cartridge.
J WARNING
If the machine is operated with a defective mains cable, there is a
danger of potentially fatal electric shock.
T Never use a machine which is damaged or has a defective
mains cable.
Precondition: The bean container has been filled.
T Insert the mains plug into a power socket.
T Press the On/Off button Q to switch the JURA on.
‘Sprachauswahl’
E To display more languages, press the ‘ > ’ button (bottom
right).
T Press the button that corresponds to the language you want,
e.g. ‘English’.
‘Saved’ appears briefly on the display to confirm the setting.
‘Water hardness’
E If you do not know the hardness of your water, you must find
this out first (see Chapter 1 ‘Preparing and using for the first
time – Determining the water hardness’).
T Press the ‘ < ’ or ‘ > ’ button to change the water hardness
setting, for example to ‘25 °dH’.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Use filter’
11
1 Preparing and using for the first time
E Now decide whether you want to operate your JURA with or
without a CLARIS Smart filter cartridge.
Operation with filter cartridge: go straight to the next section (see
Chapter 1 ‘Preparing and using for the first time – First-time use with
filter cartridge activation’).
Operation without filter cartridge (see Chapter 1 ‘Preparing and
using for the first time – First-time use without filter cartridge activation’).
First-time use with filter
cartridge activation
CAUTION
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
T Remove the water tank and rinse it with cold water.
T Fit the filter cartridge extension supplied on top of a CLARIS
Smart filter cartridge.
T Insert the filter cartridge with its extension into the water
tank.
T Turn the filter cartridge clockwise until it audibly clicks into
place.
T Fill the water tank with fresh, cold water and reinsert the
tank.
E The machine automatically detects that you have just inserted
the filter cartridge.
‘Use filter’ / ‘Saved’
‘Switch open’
T Place a receptacle (at least 300 ml) under the fine foam
frother.
T Turn the switch to the x position.
‘Filter is being rinsed’, water flows out of the fine foam
frother.
Rinsing of the filter stops automatically after approximately
300 ml. ‘Switch close’ appears on the display.
12
1 Preparing and using for the first time
T Turn the switch to the ° position.
‘Filter rinsing complete’
‘System is filling’, the system fills up with water.
‘Empty drip tray’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Machine is rinsing’, the system is rinsed. The rinse stops
automatically. Your JURA is ready for use.
E The start screen shows the products you can prepare.
E If the filter is active, this is indicated by a blue filter symbol at
the bottom of the display.
First-time use without filter
cartridge activation
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
CAUTION
T Press the ‘No filter’ button.
‘Saved’ appears briefly on the display.
‘Fill water tank’
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert the
tank.
‘Switch open’
T Place a receptacle under the fine foam frother and under the
coffee spout.
T Turn the switch to the x position.
‘System is filling’, the system fills up with water.
‘Switch close’
T Turn the switch to the ° position.
‘System is filling’
‘Machine is rinsing’, the system is rinsed. The rinse stops
automatically. Your JURA is ready for use.
E The start screen shows the products you can prepare.
13
1 Preparing and using for the first time
Connecting milk
Your JURA creates fine, creamy, feather-light milk foam with a perfect consistency. The most important requirement for frothing milk
is a milk temperature of 4–8 °C. We would therefore recommend
using a milk cooler or a vacuum milk container.
T Remove the protective cover from the fine foam frother.
T Connect the milk pipe to the fine foam frother.
T Connect the other end of the milk pipe to a milk container
or immerse it in a milk carton.
14
2 Preparation
2 Preparation
E You can stop the machine at any time while a speciality coffee,
steam or hot water is being prepared. Just press any button
(for a speciality coffee) or return the switch to its original position (for steam and hot water).
E During the grinding operation you can select the coffee
strength of single products by pressing the ‘ < ’ and ‘ > ’ buttons.
E During preparation you can change the preset amount of
water and milk foam by pressing the ‘ < ’ and ‘ > ’ buttons.
E You can follow the current status of preparation on the display.
Coffee tastes best served hot. A cold porcelain cup cools the beverage – and impairs the taste. We therefore recommend prewarming
the cups. The full coffee aroma can develop only in prewarmed cups.
You can purchase a JURA cup warmer from your specialised dealer.
You can make permanent settings for all products in programming
mode (see Chapter 4 ‘Permanent settings in programming mode –
Adjusting the product settings’).
Espresso and coffee
Example: Proceed as follows to prepare one coffee.
Precondition: The start screen is displayed.
T Place a cup under the coffee spout.
T Press the ‘Coffee’ button.
Preparation starts. ‘Coffee’ and the coffee strength are displayed. The preset amount of water for coffee flows into the
cup.
Preparation stops automatically. Your JURA is once more
ready for use.
15
2 Preparation
Two espressi and two
coffees
To prepare two speciality coffees, press the appropriate preparation
button twice (within approximately 1 second).
Example: Proceed as follows to prepare two espressi.
Precondition: The start screen is displayed.
T Place two cups under the coffee spout.
T Press the ‘Espresso’ button twice (within 1 second) to start
preparation.
‘2 espressi’ appears and the preset amount of water flows
into the cups.
Preparation stops automatically. Your JURA is once more
ready for use.
Cappuccino
Your JURA can prepare a cappuccino without the cup having to be
moved.
Precondition: The start screen is displayed. Milk is connected to the
fine foam frother
T Place a cup under the coffee spout and the fine foam frother.
T Press the ‘Cappuccino’ button.
‘Cappuccino’ / ‘Coffee strength’
As soon as the machine has heated up, ‘Switch open’
appears.
T Turn the switch to the x position.
‘Cappuccino’, the milk foam is prepared. Preparation stops
automatically when the preset amount of milk is reached.
‘Switch close’
T Turn the switch to the ° position.
Coffee preparation starts. The preset amount of water for
espresso flows into the cup.
Preparation stops automatically. Your JURA is once more
ready for use.
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk (see Chapter 5 ‘Maintenance – Cleaning the fine foam frother’).
16
2 Preparation
Milk foam
Precondition: The start screen is displayed.
T Place a cup under the fine foam frother.
T Press the ‘Milk foam’ button.
‘Milk foam’
As soon as the machine has heated up, ‘Switch open’ appears.
T Turn the switch to the x position.
‘Milk foam’, the milk foam is prepared. Preparation stops
automatically when the preset amount of milk is reached.
‘Switch close’
T Turn the switch to the ° position.
Your JURA is once more ready for use.
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk (see Chapter 5 ‘Maintenance – Cleaning the fine foam frother’).
Permanently setting the
amount of water for the
cup size
It is easy to permanently adjust the amount of water for all single
products to the cup size. Adjust the amount once as shown in the
following example. Every time you prepare a drink in the future, this
amount will be dispensed.
Example: Proceed as follows to permanently set the amount of
water for one coffee.
Precondition: The start screen is displayed. Milk is connected to the
fine foam frother
T Place a cup under the coffee spout.
T Press and hold the ‘Coffee’ button until ‘Enough coffee?
Press button’ appears.
T Release the ‘Coffee’ button.
Preparation starts and the coffee flows into the cup.
T Press any button (except ‘Cancel’) as soon as there is sufficient coffee in the cup.
Preparation stops. ‘Saved’ appears briefly on the display. The
set amount of water for one coffee is permanently stored.
Your JURA is once more ready for use.
E You can alter this setting at any time by repeating the above
procedure.
E You can also permanently set the amounts for all single products in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’).
17
2 Preparation
Adjusting the grinder
CAUTION
You can adjust the grinder on a continuous scale to suit the degree
of roast of your coffee.
If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is running.
The consistency of grind is correct if the coffee flows regularly from
the coffee spout. In addition a fine, thick crema forms.
Example: Proceed as follows to change the consistency of grind
during the preparation of an espresso.
T Place a cup under the coffee spout.
T Open the cover of the grinder adjustment switch.
T Press the ‘Espresso’ button to start preparation.
T Turn the grinder adjustment switch to the desired position
while the grinder is running.
The preset amount of water flows into the cup. Preparation
stops automatically.
T Close the cover of the grinder adjustment switch.
Hot water
To obtain a perfect water flow, use the hot-water nozzle.
J CAUTION
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
Precondition: The start screen is displayed.
T Carefully remove the fine foam frother from the Connector
System© by twisting slightly.
T Attach the hot-water nozzle to the connector.
T Place a cup under the hot-water nozzle.
T Turn the switch to the x position.
‘Hot water’, the preset amount of water flows into the cup.
Preparation stops automatically.
‘Switch close’
T Turn the switch to the ° position.
Your JURA is once more ready for use.
18
3
3
Daily operation
Daily operation
Filling the water tank
CAUTION
Daily maintenance of the machine and hygiene when handling milk,
coffee and water are key to a perfect coffee result in the cup every
time. You should therefore change the water daily.
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
T Open the water tank cover.
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Close the water tank cover.
Switching on the
machine
Daily maintenance
T Place a receptacle under the coffee spout.
T Press the On/Off button Q to switch the JURA on.
‘Welcome to JURA’
‘Machine is heating’
‘Machine is rinsing’, the system is rinsed. The rinse stops
automatically. The start screen is displayed. Your JURA is
ready for use.
To ensure that you get many years of reliable service out of your
JURA and to guarantee the optimum coffee quality, the machine
requires daily maintenance.
T Pull out the drip tray.
T Empty the coffee grounds container and the drip tray. Rinse
them both with warm water.
E Always empty the coffee grounds container when the machine
is switched on. This is the only way of resetting the coffee
grounds counter.
19
3
Daily operation
T Refit the coffee grounds container and the drip tray.
T Rinse the water tank with clean water.
T Clean the fine foam frother (see Chapter 5 ‘Maintenance –
Cleaning the fine foam frother’).
T Remove the milk pipe and rinse it thoroughly under running
water.
T Dismantle and rinse the fine foam frother (see Chapter 5
‘Maintenance – Dismantling and rinsing the fine foam
frother’).
T Wipe the surface of the machine with a clean, soft, damp
cloth (e.g. microfibre cloth).
Regular maintenance
Carry out the following maintenance actions regularly or as
required:
In the interests of hygiene, we recommend changing the milk
pipe on a regular basis (approximately every 3 months).
Replacement pipes are available from specialised dealers
(JURA original accessory set for milk systems).
Clean the inside of the water tank, e.g. with a brush. Further
information about the water tank is provided in these instructions for use (see Chapter 5 ‘Maintenance – Descaling the
water tank’).
Traces of milk and coffee may stick to the top and bottom of
the cup grille. If this happens, clean the cup grille.
U
U
U
Switching off the
machine
When the JURA is switched off, the system is automatically rinsed if
a speciality coffee has been prepared. If milk has been prepared, you
will also be prompted to clean the milk system.
Precondition: The start screen is displayed.
T Place a receptacle under the fine foam frother and under the
coffee spout.
T Press the On/Off button Q.
E If milk has been prepared, you will be prompted to clean the
milk system (‘Clean the milk system’). After 10 seconds the
switch-off process continues automatically.
20
3
Daily operation
If milk has been prepared but you have not started milk
system cleaning, the milk system is rinsed first (‘Milk system
is being rinsed’).
‘Machine is rinsing’, the system rinses itself. The operation
stops automatically. Your JURA is switched off.
21
4
Permanent settings in programming mode
4
Permanent settings in programming mode
Press the ‘ P ’ button to enter programming mode. You can navigate
through the programme items and permanently save the required
settings using the multi-function buttons. The following settings
can be made:
Programme Sub-item
item
‘1/4’
‘Clean’,
‘Descale’,
‘Clean the milk system’,
‘Filter’ (only if filter is
activated)
‘2/4’
‘Rinse the coffee system’,
‘Rinse the milk system’,
‘Information’
Explanation
‘3/4’
‘Expert mode’
T Select your settings for speciality coffees and hot
water.
‘4/4’
‘Choose language’
T Select your language.
‘Switch off after’
T Set the time after which the JURA should switch off
automatically.
‘Units’
T Select the unit for the amount of water.
‘Water hardness’
T Adjust the water hardness.
Adjusting the product
settings
Product
Espresso
Coffee
2 espressi,
2 coffees
Cappuccino
Milk foam
Hot water
22
T Start the required maintenance programme here.
T Here you can start the desired maintenance
programme or find out what maintenance actions are
required.
In the programme item ‘Expert mode’ you can make individual settings for all speciality coffees and hot water. The following permanent settings can be made:
Coffee strength
8 levels
8 levels
–
8 levels
–
–
Amount
Water: 15 ml – 80 ml
Water: 25 ml – 240 ml
Water: the amount set for the
single product is doubled.
Water: 25 ml – 240 ml
Milk foam: 3 sec. – 120 sec.
Milk foam: 3 sec. – 120 sec.
Water: 25 ml – 450 ml
Temperature
normal, high
normal, high
as for single product
normal, high
–
low, normal, high
4
Permanent settings in programming mode
Permanent settings in programming mode always follow the same
model.
Example: Proceed as follows to change the coffee strength for one
coffee.
Precondition: The start screen is displayed.
T Press the ‘ P ’ button.
T Press the ‘ > ’ button several times until ‘3/4’ is displayed.
T Press the ‘Expert mode’ button.
‘Expert mode’
E Next select the button of the product for which you would like
to make settings. No product is prepared at this point.
E To display more products, press the ‘ > ’ button (bottom right).
T Press the ‘Coffee’ button.
‘Coffee’
T Press the ‘Coffee strength’ button.
‘Coffee’ appears and the coffee strength is displayed.
T Press the ‘ < ’ or ‘ > ’ button to change the setting for the
coffee strength.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘Coffee’
T Press the ‘’ button for around 2 seconds to exit programming mode.
The start screen is displayed.
Automatic switch-off
By instructing your JURA to automatically switch itself off, you can
cut down your energy consumption. If this function is activated,
your JURA switches off automatically after the preset time following
the last action on the machine.
You can set the automatic switch-off to 15 minutes, 30 minutes or
1–9 hours.
Precondition: The start screen is displayed.
T Press the ‘ P ’ button.
T Press the ‘ > ’ button several times until ‘4/4’ is displayed.
T Press the ‘Switch off after’ button.
‘Switch off after’
23
4
Permanent settings in programming mode
T Press the ‘ < ’ or ‘ > ’ button to change the switch-off time.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘4/4’
T Press the ‘’ button to exit programming mode.
The start screen is displayed.
Setting the water
hardness
The harder the water is, the more frequently the JURA needs to be
descaled. It is therefore important to set the water hardness accurately.
The water hardness was set when the machine was first used. You
can change this setting at any time.
The water hardness can be adjusted on a continuous scale between
1 °dH and 30 °dH.
Precondition: The start screen is displayed.
T Press the ‘ P ’ button.
T Press the ‘ > ’ button several times until ‘4/4’ is displayed.
T Press the ‘Water hardness’ button.
‘Water hardness’
T Press the ‘ < ’ or ‘ > ’ button to change the setting for the
water hardness.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘4/4’
T Press the ‘’ button to exit programming mode.
The start screen is displayed.
Unit for amount of water
In the programme item ‘Units’ you can select the unit used for the
amount of water.
Example: Proceed as follows to change the unit for the amount of
water from ‘ml’ to ‘oz’.
Precondition: The start screen is displayed.
T Press the ‘ P ’ button.
T Press the ‘ > ’ button several times until ‘4/4’ is displayed.
T Press the ‘Units’ button.
‘Units’
24
4
Permanent settings in programming mode
T Press the ‘oz’ button.
T Press the ‘Save’ button.
‘Saved’ appears briefly on the display.
‘4/4’
T Press the ‘’ button to exit programming mode.
The start screen is displayed.
Language
In this programme item you can set the language used by your
JURA.
Example: Proceed as follows to change the language from ‘English’
to ‘Deutsch’.
Precondition: The start screen is displayed.
T Press the ‘ P ’ button.
T Press the ‘ > ’ button several times until ‘4/4’ is displayed.
T Press the ‘Choose language’ button.
‘Choose language’
E To display more languages, press the ‘ > ’ button (bottom
right).
T Press the button that corresponds to the language you want,
e.g. ‘Deutsch’.
‘Gespeichert’ appears briefly on the display.
‘4/4’
T Press the ‘’ button to exit programming mode.
The start screen is displayed.
25
5
5
Maintenance
Maintenance
Your JURA has the following integrated maintenance programmes:
Rinsing the machine (‘Rinse the coffee system’)
Rinsing the fine foam frother (‘Rinse the milk system’)
Cleaning the fine foam frother (‘Clean the milk system’)
Changing the filter (‘Change the filter’)
Cleaning the machine (‘Clean’)
Descaling the machine (‘Descale’)
U
U
U
U
U
U
E Carry out each maintenance programme when you are
prompted to do so.
E Press the ‘ P ’ button to view a list of the maintenance programmes. When the bar is completely filled with red, your
JURA will prompt you to perform the appropriate maintenance programme.
E Press the ‘ c ’ button (white Maintenance symbol) to go
straight to the programme item ‘2/4’. Here you can start milk
system rinsing and coffee system rinsing or find out what
maintenance actions are required.
Rinsing the machine
You can start coffee system rinsing manually at any time.
Precondition: The start screen is displayed.
T Place a receptacle under the coffee spout.
T Press the ‘ c ’ button (white Maintenance symbol).
T Press the ‘Rinse the coffee system’ button to start the rinse
operation.
‘Machine is rinsing’, water flows out of the coffee spout. The
operation stops automatically. The start screen is displayed.
Rinsing the fine foam
frother
After each milk preparation, the JURA prompts you to perform a milk
system rinse.
Precondition: ‘Rinse the milk system’ is displayed.
26
5
Maintenance
T Place a receptacle under the fine foam frother.
T Press the ‘ c ’ button (red Maintenance symbol).
‘Switch open’
T Turn the switch to the x position.
‘Milk system is being rinsed’appears and the fine foam
frother is rinsed.
The rinse stops automatically. ‘Switch close’ appears on the
display.
T Turn the switch to the ° position.
The start screen is displayed.
Cleaning the fine foam
frother
CAUTION
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
E JURA milk system cleaner is available from specialised dealers.
Precondition: The start screen is displayed.
T Press the ‘ P ’ button.
T Press the ‘Clean the milk system’ button.
‘Clean the milk system’
T Press the ‘Start’ button.
T Press the ‘Next’ button.
‘Clean the milk system’ / ‘Milk system cleaner’
T Remove the milk pipe from the milk container or carton.
T Pour 250 ml of fresh water into a receptacle and add 1 capful
of milk system cleaner.
T Immerse the milk pipe in the receptacle.
T Place a receptacle under the fine foam frother.
T Press the ‘Next’ button.
As soon as the machine has heated up, ‘Switch open’
appears.
T Turn the switch to the x position.
‘Milk system is being cleaned’ appears and the fine foam
frother and the milk pipe are cleaned.
‘Switch close’
27
5
Maintenance
T Turn the switch to the ° position.
‘Clean the milk system’
T Rinse the receptacle thoroughly, fill it with 250 ml of fresh
water and immerse the milk pipe in the water.
T Empty the other receptacle and place it under the fine foam
frother once more.
T Press the ‘Next’ button.
‘Switch open’
T Turn the switch to the x position.
‘Milk system is being cleaned’ appears and the fine foam
frother and the milk pipe are rinsed with fresh water.
‘Switch close’
T Turn the switch to the ° position.
The start screen is displayed.
Dismantling and rinsing
the fine foam frother
To make sure the fine foam frother works properly, and in the interests of hygiene, it must be dismantled and rinsed daily if you have
been preparing milk. Your JURA will not prompt you to dismantle
and rinse the frother.
T Remove the milk pipe and rinse it thoroughly under running
water.
T Carefully remove the fine foam frother from the Connector
System© by twisting slightly.
T Dismantle the fine foam frother into its individual parts.
T Rinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 250 ml cold water and 1 capful of JURA milk
system cleaner. Then rinse the parts thoroughly.
T Re-assemble the fine foam frother.
E Ensure that all individual parts are correctly and firmly
connected to ensure optimum operation.
T Firmly attach the fine foam frother to the Connector
System©.
Inserting the filter
28
Your JURA no longer has to be descaled if you are using the CLARIS
Smart filter cartridge. If you did not insert the filter cartridge the first
time you used the machine, you can do this now as follows.
5
Maintenance
Precondition: The start screen is displayed.
T Remove and empty the water tank.
T Fit the filter cartridge extension supplied on top of a CLARIS
Smart filter cartridge.
T Insert the filter cartridge with its extension into the water
tank.
T Turn the filter cartridge clockwise until it audibly clicks into
place.
T Fill the water tank with fresh, cold water and reinsert the
tank.
E The machine automatically detects that you have just inserted
the filter cartridge.
‘Saved’ appears briefly on the display.
‘Switch open’
T Place a receptacle (at least 300 ml) under the fine foam
frother.
T Turn the switch to the x position.
‘Filter is being rinsed’, water flows out of the fine foam
frother.
Rinsing of the filter stops automatically after approximately
300 ml. ‘Switch close’ appears on the display.
T Turn the switch to the ° position.
The start screen is displayed.
E If the filter is active, this is indicated by a blue filter symbol at
the bottom of the display.
Changing the filter
E Once the filter cartridge stops working (depending on the
water hardness setting), the JURA will prompt you to change
the filter.
E CLARIS Smart filter cartridges are available from specialised
dealers.
Precondition: The start screen is displayed. The filter symbol at the
bottom of the display lights up red.
T Remove and empty the water tank.
T Turn the filter cartridge anticlockwise and remove it along
with the extension from the water tank.
29
5
Maintenance
T Fit the filter cartridge extension on top of a new CLARIS
Smart filter cartridge.
T Insert the filter cartridge with its extension into the water
tank.
T Turn the filter cartridge clockwise until it audibly clicks into
place.
T Fill the water tank with fresh, cold water and reinsert the
tank.
‘Saved’ appears briefly on the display. The machine has
automatically detected that you have just changed the filter
cartridge.
‘Switch open’
T Place a receptacle (at least 300 ml) under the fine foam
frother.
T Turn the switch to the x position.
‘Filter is being rinsed’, water flows out of the fine foam
frother.
E You can interrupt rinsing of the filter at any time. To do this,
turn the switch clockwise. Turn the switch anticlockwise to
continue rinsing the filter.
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
300 ml. ‘Switch close’ appears on the display.
T Turn the switch to the ° position.
The start screen is displayed.
Cleaning the machine
CAUTION
After 180 preparations or 80 switch-on rinses, the JURA will prompt
you to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
E The cleaning programme lasts approximately 20 minutes.
E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E JURA cleaning tablets are available from specialised dealers.
30
5
Maintenance
Precondition: ‘Clean machine’ is displayed.
T Press the ‘ c ’ button (red Maintenance symbol).
‘Clean’
T Press the ‘Start’ button.
T Press the ‘Next’ button.
‘Empty coffee grounds container’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Clean’
T Place a receptacle under the coffee spout.
T Press the ‘Next’ button.
‘Machine is being cleaned’, water flows out of the coffee
spout.
The operation is interrupted, ‘Add cleaning tablet’.
T Open the cover of the filler funnel for the cleaning tablet.
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
T Press the ‘Next’ button.
‘Machine is being cleaned’, water flows out of the coffee
spout several times.
The operation stops automatically.
‘Empty coffee grounds container’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
Cleaning is now complete. The start screen is displayed.
Descaling the machine
The JURA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water.
E If you are using a CLARIS Smart filter cartridge, you will not be
prompted to descale.
J CAUTION
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
31
5
Maintenance
CAUTION
If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
CAUTION
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling programme to run to the end.
CAUTION
If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
T Clean up any splashes immediately.
E The descaling programme lasts approximately 40 minutes.
E JURA descaling tablets are available from specialised dealers.
Precondition: ‘Decalcify machine’ is displayed.
T Press the ‘ c ’ button (red Maintenance symbol).
‘Descale’
T Press the ‘Start’ button.
T Press the ‘Next’ button.
‘Empty drip tray’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Agent in tank’
T Remove and empty the water tank.
T Completely dissolve the contents of one blister (3 JURA descaling tablets) in a receptacle holding 500 ml of lukewarm
water. This may take several minutes.
T Pour the solution into the empty water tank and insert it into
the machine.
‘Switch open’
T Place a receptacle under the fine foam frother.
T Turn the switch to the x position.
‘Machine is being descaled’ appears and water flows out of
the fine foam frother repeatedly.
The operation is interrupted, ‘Switch close’.
32
5
Maintenance
T Turn the switch to the ° position.
‘Machine is being descaled’, the descaling operation is
continued.
The operation is interrupted, ‘Empty drip tray’.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Fill water tank’
T Empty the receptacle and place it under the fine foam
frother and the coffee spout.
T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
‘Switch open’
T Turn the switch to the x position.
‘Machine is being descaled’, the descaling operation is continued.
The operation is interrupted, ‘Switch close’.
T Turn the switch to the ° position.
‘Machine is being descaled’, the descaling operation is continued. Water flows out of the coffee spout.
The operation is interrupted ‘Empty drip tray’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
Descaling is now complete. The start screen is displayed.
E If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
Cleaning the bean
container
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These traces may negatively affect
the coffee result. For this reason clean the bean container from time
to time.
Precondition: ‘Fill bean container’ is displayed.
T Switch the machine off with the On/Off button Q.
T Remove the aroma preservation cover.
T Clean the bean container with a soft, dry cloth.
T Fill the bean container with coffee beans and close the
aroma preservation cover.
33
5
Maintenance
Descaling the water tank
34
Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
T Remove the water tank.
T If you use a CLARIS Smart filter cartridge, remove this.
T Completely fill the water tank and dissolve 3 JURA descaling
tablets in it.
T Leave the water tank with the descaling solution for several
hours (e.g. overnight).
T Empty the water tank and rinse it thoroughly.
T If you use a CLARIS Smart filter cartridge, insert this again.
T Fill the water tank with fresh, cold water and reinsert the
tank.
6 Display messages
6 Display messages
Message
‘Fill water tank’
Cause/Result
The water tank is empty. You
cannot prepare any products.
‘Empty coffee
grounds
container’
The coffee grounds container is
full. You cannot prepare any
products.
T Empty the coffee grounds container
and the drip tray (see Chapter 3 ‘Daily
operation – Daily maintenance’).
‘Drip tray not
fitted’
The drip tray is not inserted
correctly or is not inserted at all.
You cannot prepare any products.
The bean container is empty. You
cannot prepare any speciality
coffees, but you can prepare hot
water and milk.
The JURA requests a milk system
rinse.
T Fit the drip tray.
The filter cartridge no longer
works.
T Replace the CLARIS Smart filter
cartridge (see Chapter 5 ‘Maintenance –
Changing the filter’).
The JURA is prompting you to
clean it.
T Perform cleaning (see Chapter 5
‘Maintenance – Cleaning the machine’).
‘Decalcify
machine’
The JURA is prompting you to
descale it.
T Perform descaling (see Chapter 5
‘Maintenance – Descaling the
machine’).
‘Too hot’
The system is too hot to start a
maintenance programme.
T Wait for several minutes until the
system has cooled or prepare a
speciality coffee or hot water.
‘Fill bean
container’
‘Rinse the milk
system’
The filter symbol
at the bottom of
the display lights
up red.
‘Clean machine’
Action
T Fill the water tank (see Chapter 3
‘Daily operation – Filling the water
tank’).
T Fill the bean container (see Chapter 1
‘Preparing and using for the first time –
Filling the bean container’).
T Perform milk system rinsing (see
Chapter 5 ‘Maintenance – Rinsing the
fine foam frother’).
35
7
Troubleshooting
7
Troubleshooting
Problem
Insufficient foam is
produced when the milk is
frothed or milk sprays out
of the fine foam frother.
Cause/Result
The fine foam frother is dirty.
Coffee only comes out in
drips when it is being
prepared.
The coffee is ground too finely
and obstructs the system. The
water hardness may not have
been correctly set.
T Set the grinder to a coarser
setting (see Chapter 2 ‘Preparation – Adjusting the grinder’).
T Perform descaling
(see Chapter 5 ‘Maintenance –
Descaling the machine ’).
‘Fill water tank’ is displayed
although the water tank is
full.
The water tank float is trapped.
T Descale the water tank (see
Chapter 5 ‘Maintenance –
Descaling the water tank’).
Little or no water or steam
comes out of the fine foam
frother. The pump is very
quiet.
The connector of the fine foam
frother may be blocked by milk
residues or limescale fragments
loosened during descaling.
T Remove the fine foam frother.
T Unscrew the black connector.
T Clean the connector thoroughly.
T Screw the connector back on
tightly by hand.
Grinder is making a very
loud noise.
There are foreign objects in the
grinder.
T Contact customer support in
your country (see Chapter 11
‘JURA contact details / Legal
information’).
‘ERROR 2’ or ‘ERROR 5’ is
displayed.
If the machine has been
exposed to the cold for a long
period of time, heating may be
disabled for safety reasons.
T Warm the machine at room
temperature.
36
Action
T Clean the fine foam frother
(see Chapter 5 ‘Maintenance –
Cleaning the fine foam frother’).
T Dismantle and rinse the fine
foam frother (see Chapter 5
‘Maintenance – Dismantling and
rinsing the fine foam frother’).
7
Problem
Other ‘ERROR’ messages
are displayed.
Cause/Result
Troubleshooting
Action
–
T Switch the JURA off with the On/
Off button Q. Contact customer
support in your country (see
Chapter 11 ‘JURA contact details /
Legal information’).
E If you were unable to solve the problem, contact customer
support in your country (see Chapter 11 ‘JURA contact details /
Legal information’).
37
8
8
Transport and environmentally friendly disposal
Transport and environmentally friendly disposal
Transport / Emptying the
system
Keep the packaging for your JURA. It should be used to protect the
machine during transport.
In order to protect the JURA from frost during transport, the system
must be emptied.
Precondition: The start screen is displayed.
T Remove the milk pipe from the fine foam frother.
T Place a receptacle under the fine foam frother.
T Press the ‘Milk foam’ button.
As soon as the machine has heated up, ‘Switch open’
appears.
T Turn the switch to the x position.
‘Milk foam’ appears and hot steam is discharged from the
fine foam frother.
T Remove and empty the water tank.
T Press the ‘ > ’ button several times until ‘Amount of milk’ /
‘60 sec.’ is displayed.
Steam will continue to be discharged from the fine foam
frother until the system is empty.
‘Switch close’
T Turn the switch to the ° position.
‘Fill water tank’
T Press the On/Off button Q.
Your JURA is switched off.
Disposal
38
Please dispose of old machines in an environmentally neutral way.
H
Old machines contain valuable, recyclable materials which should
be recycled. Please therefore dispose of old machines via suitable
collection systems.
9 Technical data
9 Technical data
Voltage
Power
Conformity mark
Pump pressure
Holding capacity of water tank (without
filter)
Holding capacity of bean container
Holding capacity of coffee grounds
container
Cable length
Weight
Dimensions (W × H × D)
220–240 V ~, 50 Hz
1450 W
A
static, max. 15 bar
1.9 l
280 g
max. 16 portions
approx. 1.1 m
approx. 9.6 kg
28.0 × 35.1 × 43.9 cm
Information for testers (repeat test in accordance with DIN VDE
0701-0702): The central grounding point (CGP) is located on the
underside of the machine, right next to the mains cable's connection point.
39
10
Index
10
A
B
C
Index
Addresses 44
Adjusting the product settings 22
Aroma preservation cover
Bean container with aroma preservation
cover 4
Automatic switch-off 23
Bean container
Bean container with aroma preservation
cover 4
Cleaning 33
Filling 10
Bus bar
Technical data 39
Button
On/Off button 4
Cappuccino 16
Cappuccino frother rinsing 26
Central grounding point 39
CLARIS Smart filter cartridge
Changing 29
Insert 28
Cleaning
Bean container 33
Fine foam frother 27
Machine 30
Coffee 15
Two coffees 16
Coffee grounds container 4
Coffee spout
Height-adjustable coffee spout 4
Consistency of grind
Adjusting the grinder 18
Grinder adjustment switch 4
Contact details 44
Cover
Filler funnel for cleaning tablet 4
Water tank 4
Cup grille 4
Customer support 44
D
E
F
G
H
I
40
Descaling
Machine 31
Water tank 34
Display 5
Display messages 35
Disposal 38
Double product 16
Drip tray 4
Emptying the system 38
Errors
Troubleshooting 36
Espresso 15
Two espressi 16
Filler funnel
Filler funnel for cleaning tablet 4
Filling
Bean container 10
Water tank 19
Filter
Changing 29
Insert 28
Fine foam frother 4
Cleaning 27
Dismantling and rinsing 28
Rinsing 26
First-time use 11
With filter cartridge activation 12
Without filter cartridge activation 13
Grinder adjustment switch 4
Grounding point 39
Height-adjustable coffee spout 4
Hotline 44
Hot water 18
Hot water and steam preparation
Switch for hot water and steam preparation 5
Internet 10
10
J
L
M
P
JURA
Contact details 44
Internet 10
R
Language 25
Machine
Cleaning 30
Descaling 31
Regular maintenance 20
Rinsing 26
Setting up 10
Switching off 20
Switching on 19
Mains cable 4
Maintenance 26
Daily maintenance 19
Regular maintenance 20
Messages, display 35
Milk
Connecting milk 14
Milk foam 17
Permanently setting the water for the cup
size 17
Permanent settings in programming mode
22
Preparation 15
Cappuccino 16
Coffee 15
Espresso 15
Hot water 18
Milk foam 17
Two coffees 16
Two espressi 16
Two speciality coffees 16
Problems
Troubleshooting 36
Product settings
Adjusting 22
Programming mode 22
Automatic switch-off 23
Language 25
Setting the water hardness 24
Unit for amount of water 24
Proper use 6
S
T
U
Index
Regular maintenance 20
Rinses
Cappuccino frother rinsing 26
Rinsing
Fine foam frother 26
Machine 26
Safety 6
Safety information 6
Settings
Permanent settings in programming
mode 22
Setting up
Setting up the machine 10
Short operating instructions 10
Switch for hot water and steam preparation
5
Switching off 20
Switching on 19
Switch-off
Automatic switch-off 23
Symbol description 3
Technical data 39
Tel 44
Transport 38
Troubleshooting 36
Two products 16
Unit for amount of water 24
Use, First-time 11
W
Water hardness
Determining the water hardness 10
Setting the water hardness 24
Water tank 4
Descaling 34
Filling 19
Website 10
41
42
43
J72123/E6-E60/en/201503
11 JURA contact details / Legal information
11 JURA contact details / Legal information
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Tel. +41 (0)62 38 98 233
@ You will find additional contact details for your country at
www.jura.com.
Directives
Technical changes
44
The machine complies with the following directives:
2006/95/EC – Low Voltage Directive
2004/108/EC – Electromagnetic Compatibility
2009/125/EC – Ecodesign Directive
2011/65/EU – RoHS Directive
U
U
U
U
We reserve the right to make technical changes. The diagrams used
in these instructions for use are for illustration purposes only and do
not represent the original colours of the machine. Some details of
your JURA may vary.
Feedback
Your opinion is important to us! Use the contact details at
www.jura.com.
Copyright
The instructions for use contain information which is protected by
copyright. It is not permitted to photocopy these instructions for use
or translate them into another language without the prior written
consent of JURA Elektroapparate AG.