n. 1 composite washing unit model lpin60v automatic bedpan and

N. 1 COMPOSITE WASHING UNIT MODEL LPIN60V
AUTOMATIC BEDPAN AND URINAL WASHERS MODEL LP/IN90-S/D.T.A SELF-PRODUCED STEAM
DISINFECTION
Device operating with a water network pressure ranging between 2 and 9 bar. Equipment
specifically built to empty, wash, rinse, thermally disinfect and partially dry bedpans and urinals.
Structure in AISI 304 stainless steel. Main element with a front folding door, controlled by shock
absorbers. Bedpan hooking and locking bedpan device suitable for all types of bedpans and clinical
containers, mounted on the door and meant for emptying during the closure. An electro-lock is
intended to prevent the operator from opening the door during the operation or in case of failure.
Stainless steel AISI316 washing chamber moulded without weld equipped with n. 2 rotating nozzles
and n. 4 fixed nozzles stainless steel meant for washing and rinsing bedpans. Independent jet for
washing urinals internally and externally. Steam delivered by a proper nozzle. Water storage tank
having a capacity of 15lt, electronic probe level.
Side element including the solenoid valves for the inlet of hot and cold water from the water
network, electronic central unit for function control, remote control switch of resistances for steam
production. Front panel wit a back lighted alphanumeric liquid crystal display complete with a cycle
start key, a key for the selection of cycle options and two keys for programming functions, a serial
plug intended to download stored data(temperatures, failures, number of washings, cycle
date/time). Mushroom-shaped emergency button with a manual lock and reset device. Power
supply of control devices at a 5V dc very low safety voltage. Steam producer and safety thermostat
that can be manually reset, Geberit drain trap Dia. 90mm. anti-limestone liquid drum with aspiration
and minimum level control, anti-limestone liquid dosing pump. Washing motor-driven pump 0.8
kW 230V.
The automatic washing system, rinsing and disinfecting cycle, with the possibility of time regulation
is electronically programmed. It consists of the following phases that are automatically executed
after the start button has been pressed:
Loading cold water in the storage tank
Washing with cold water
Loading hot water in the storage tank
Rinsing with hot water
Steam Disinfection with automatic calculation of A0 and following drying
Cooling the containers by cold water
The equipment enables the operator to choose at the start-up the washing and disinfecting cycle
most suitable for the needs of the type of container you wish to wash. Three basic cycles are
available with some possibilities of customization. The features are listed in details here below:
SHORT CYCLE: It is intended to rinse with hot water with the possibility of adding a
detergent/chemical disinfectant, followed by steam disinfection. Suitable for urinals or other
containers that are not too dirty.
NORMAL CYCLE: It is intended to pre-wash with hot water and to rinse with hot water with
the possibility of adding a detergent/chemical disinfectant, followed by a steam disinfection.
Suitable for bedpans, close-stools, chamber pots or other containers.
INTENSIVE CYCLE: It is intended to pre-wash with cold water, to wash with hot water and to
rinse with hot water with the possibility of adding a detergent/chemical disinfectant,
followed by a steam disinfection
Total installed power: 4 kW
Maximum power absorbed by the steam producer: 3kW
Out bedpan washers have the EC Mark and comply with the following directives: 93/42 EEC class II
(Non-invasive medical device), 89/392 EEC, 89/336, 73/23 EEC, as well as the following
harmonised standards CEI EN 61010-1, CEI EN 61010-2-045, EN 61000/3-2, EN 61000/3-3, EN
55014, EN55104, EN 15883 PART 1-3.
Please note: The bedpan washer is supplied with the first METALCAL filling (anti-limestone product).
Feeding voltage: 220V 1F + N + T
Feeding on request: 380V 3F + N + T
Equipment sizes in mm. 900 x 460 x 900.
EMPTY UNIT/SLOP HOPPER MODEL 020
Completely made in stainless steel AISI 304. Moulded sink mm. 400x400x200 h. complete with n. 4
spraying nozzles. Hand operated tap and quickly tap for operation of nozzles. Complete with siphon,
removable grill. Closed on the perimeter, on the front removable panel. Dimensions mm.
500x600x900h.
SINK MODEL 021-600
Built with AISI 304 18/10 stainless steel; 1.2mm and 1.5mm thickness. Hygienic and bactericide
worktop. Sink equipped with basin mm. 500x400x250 complete with drain, trap and
distributor/mixing unit with elbow control. Back riser 100mm height. The area below is closed on
both sides, has a front wing door and is open on the rear to receive water connections. Dimensions
mm 600x500x900 h.
Total dimensions 2000x600x900
OPTIONAL DEVICES
Disinfecting/detergent pump provided with min. level signalling Instr. (SEE NOTE 2)
Additive pump rinse aid (SEE NOTE 3)
Double support frame for n. 3 bottles and/or 2 lt. container
Obstructed drain trap
NOTE 1
The system, as required by the ISO 15883, it is endowed with a double sensor of temperature
(process sensor and control sensor), which provides to signal the anomaly in case the read
temperatures differs of + or – 2°C, besides the operator can choose to perform the cycle with
priority to temperature or priority to A0 value, moreover can set the A0 value and the temperature
of disinfection.
With the priority method A0 value established by the norm for human waste containers shall be at
least 60). The cycle with temperature rising, and it arrests the disinfection to the attainment of the
preset A0 value (the A0 value established by the norm for human waste containers shall be at least
60). The cycle with temperature priority foresees that the disinfection if performed up to the
attainment of the temperature and the time settled, at the end of which the A0 value reached is
showed on display card which has to be equal or superior to the value planned.
NOTE 2 DETERGENT PUMP
The pump, after the programming of the output time and determinate the water quantity in the
tank, add directly in the tank the detergent/disinfecting.
The function can be enabled and/or disabled directly from display on the following phases: prewash, wash and rinse and rinse only.
NOTE 3 PUMP AND RINSE AID
The pump, after the programming of the output time and determinate the water quantity and
hardness in the tank, add directly the polishing for the phase of the final rinse, improving the phase
of the drier and the elimination of the residual limestone.
The function can enable and/or disenable directly from display.
KENT BEDPAN UNITS TYPICAL COMPOSITE OF VARIOUS MODELS
Various Floor and Wall mounted versions
Automatic and manual opening/closure
Touch less sensor
Fixed and rotating nozzles
**Supplied/Commissioned/Serviced and on site Training by Kent Certified Technicians **Working
DEMO Model in Kent Showroom**