K917D-L-BW - SAN-EI Faucet Mfg Co.,Ltd.

LIMITED WARRANTY
SAN-EI products have been manufactured under the highest standards of quality
and workmanship, and warrants to the original consumer purchaser that its products
are free of defects in material and workmanship.
1. Ceramic cartridges and PVD finishes carry a limited lifetime warranty to the
Original Consumer Purchaser for as long as that consumer purchaser owns his/
her/their home. All other parts are warranted for 2 years after the date of purchase.
2. SAN-EI warrants to the Commercial Purchaser that their products, purchased for
commercial, industrial or other business use, are free from defects of workmanship
and materials for a period of 1 year after the date of purchase.
All warranties are to the original purchaser and require presentation of original sales
receipt. Warranty is not transferable. During the warranty period, SAN-EI will, at
its option, repair or replace any part or parts which have been determined to
be defective if returned at purchaser’s expense. This shall be the sole remedy
available under this warranty. Defects or damage caused by the use of other
than genuine SAN-EI parts are not covered by this warranty. Installation or any
other labor charges associated with the repair or re-installation of SAN-EI
products is not covered by this warranty. Damage due to improper installation,
misuse, poor maintenance practices, accident, alcohol, or other organic solvents, or
use in any manner contrary to the written instructions provided, whether done by
contractor, service company, or end user, are excluded from this warranty. Some
states, provinces and nations do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state, province to province, nation to nation.
SAN-EI will advise you of the procedure to follow in making warranty claims. Simply
write to explain the defect and include product instruction manual, along with original
proof of purchase receipt showing the store name, address and date of purchase.
Be sure to include your name, address and telephone number.
BW-0BH
INSTALLATION INSTRUCTIONS
K917D-L-BW
TWO HANDLE
Roman Tub Faucet
Tools
For safety and easy faucet replacement, San-Ei recommends the use of
the following helpful tools:
SAFETY GLASSES
ADJUSTABLE WRENCH
PIPE WRENCH
PLIERS
BASIN WRENCH
CHANNEL LOCKS
PHILLIPS SCREWDRIVER
FLASHLIGHT
About This Manual
CONTACT
Toll Free: 1(800) 222-RWVC(7982)
In the United States, please kindly call our toll free number
for answers to any product, installation, or warranty questions.
RED-WHITE VALVE CORP.
20600 REGENCY LANE, LAKE FOREST, CA 92630 U.S.A.
Phone
:
(949) 859-1010
- 8-
Keep Instructions for Future Reference
Thank you for purchasing San-Ei’s quality faucet.
With simple care and maintenance, it will provide you with many years of reliable
performance.
Please read instructions before installation.
TIPS FOR REMOVAL OF OLD FAUCET
CAUTION: Always turn water OFF before removing existing faucet or
disassembling the faucet.
Open the faucet handles to relieve water pressure and ensure that
complete water shut-off has been accomplished.
(Complies with ASME A112.18.1)
-1-
PARTS LIST
FLUSHING INSTRUCTIONS
The structure shown is an illustration.
Please use this structure for better understanding.
1
1
2
2
8
K917D-L-BW
3
General Description
1. Cap
2. Screw
3. Handle (Blue)
4. Handle Escutcheon
5. Seat packing
6. Click Cartridge Top Portion
7. Rubber Packing
8. Handle (Red)
9. Body
10. Socket
11. Union Nut
12. Seat Packing
13. Spout
14. Protection Top Cover
15. Protection Under Cover
16. Aerator
17. Rubber Packing
18. Net Filter
19. Aerator Body
4
5
13
14
6
12
IMPORTANT! : Pipe chips, sand, stones and other solid found in new and
renovated plumbing can damage the cealing of the cartridge and
cause leaks to avoid damage,
DO NOT TURN ON SUPPLY VALVES until instructed below.
1. After installing and connecting your new faucet, turn on in the full cold position
(handle pointing to the right) and turn on the cold supply for 15 seconds.
2. Loosen nut and remove supply lines Re-connect each supply lines into different
supply stop valves.(Excessive bending will cause leaking and damage to the
lines.) Then, tighten each of supply lines.
3. Close the handle, then using a towel unscrew the aerator from the end of the
spout and clean the aerator.
4. Using a towel replace the aerator and check the system for leaks.
TROUBLESHOOTING
TO CORRECT REVERSED HOT AND COLD POSITIONS :
1. Shut off both stop valves. Then, open faucet handles to relieve water pressure
that complete water shut-off has been accomplished.
2. Loosen nut and remove supply lines. Re-connect each supply lines into different
supply stop valves.(Excessive bending will cause leaking and damage to the
lines.) Then, tighten each of supply lines.
3. Re-installing and connecting, turn on both cold and hot supply.
4. Turn on in the full position, make sure that the each positions keeps correct way
& make sure any water leakage.
15
16
7
17
MAINTENANCE
Care and Cleaning of Chrome and Special Finishes
18
19
9
Do not use abrasive or chemical cleaners (including chlorine bleach) to clean faucets
as they may dull the luster and attack the chrome or special decorative finishes.
Use ONLY soap and water, then wipe dry with clean cloth or towel.
10
While cleaning the bathroom tile, the faucet should be protected from any splattering
of cleaner. Acids and cleaning fluids will discolor or remove chrome plating.
11
-2-
- 7-
CARTRIDGE REPLACEMENT
OPERATION
Roman Tub Faucet
K917D-L-BW
Installation Dimension
Please kindly follow the installation dimension.
Improper installation may cause that water is
not coming out to the tub.
1
2
Spout 9-2/5"(240mm)
MIN 2"(50mm)
6
3
Rim Width
A
4
Spout 9-2/5"(240mm)
Rim Width
A
Below 2-4/5"(70mm)
Between 2"(50mm) to 5-3/10"(135mm)
3-1/2"(90mm)
3-9/10"(100mm)
Between 2"(50mm) to 4-1/2"(115mm)
Between 2"(50mm) to 3-1/10"(105mm)
4-7/10"(120mm)
Between 2"(50mm) to 3-3/10"(85mm)
5-1/2"(140mm)
Between 2"(50mm) to 2-3/5"(65mm)
6-1/10"(155mm)
Over 6-1/2"(165mm)
7
2"(50mm)
Can not be used.
1. Remove the top cap(1) from the handle(3) and loosen the screw(2) with
screw driver.
2. After removing the handle(3), loosen the handle escutcheon(4). (counter
clockwise) Also remove the seat packing(5).
3. Remove the spindle parts set(6) with pliers.
4. Remove an old rubber packing(7) with pliers and replace a new rubber packing(7).
5. To reassemble, reverse the previous steps.
4-3/10"(110mm)
2-9/10"(73mm)
2-9/10"(73mm)
Caution!:
Always turn water OFF before removing the cartridge. Open the handle to relieve
water pressure and ensure that water shut-off has been accomplished.
2-1/10"(53mm) 2-4/5"(70mm)
9-2/5"(240mm)
5
7-9/10"(200mm)
Please connect socket with union nut
onto supply pipe.
Then, the length between top surface
level and supply the level should keep
3-2/5"(88mm)
1/5"(5mm).
(Both supply line level should be the
same level each other.)
1/2-14 NPT
Tile Surface
3-2/5"(88mm)
1/5"(5mm)
Socket
Union
Nut
7-9
/10
"(2
00
mm
)
-6-
-3-
Hot water
4,5
6
Stop
1
2
13
Flow
3
Cold water
12
Important !
* All plumbing is to be installed in accordance with applicable codes and
regulations.
* Flush all water lines prior to making connection.
4
Cure Cap
Tile Surface
5
Sealing
INSTALL FAUCET
1. Installation
1,2
3
Cure Cap
Put a grain of sand to be fixed
Vinyl Cover
(1) Connect water supply line with faucet body(9). (Tighten the union nut.)
SAN-EI logo on the faucet bodys(9) should keep facing to inside bath tub.
(In case you install the opposite direction, faucet spout(13) can not be
installed.)
(2) Cure Cap should be covered until the tiles are laid. The cure cap indicates
the level where surface should be finished.
NOTE : Please pay attention the level indication whether finished surface is within
the mentioned level or not.
2. Inspection
After installing and connecting the faucet body(9), turn on supply valve to check
the water leakage.
SAN-EI Logo
3. Assemble parts
9
All thread portion, spindle portion should be covered or wrapped with such as
vinyl in advance.
4. Tile finishing
Please pay attention that the finished surface of tiling should be within the
mentioned level or not.
Upper
Level
NOTE : Please pay attention the installation, not to put sand or mortar into the
faucet body(9) or cure caps.
Bottom
Standard Level Level
5. Remove "cure caps" from the faucet body
6. Assemble handles and faucet spout
To protect water going to the cracked space of tiles, put the sealing material to
the cracked space. Then, assemble handles(3) and spout(13), referring to the
following indication. (Excess sealing should be removed perfectly.)
-4-
-5-
Hot water
4,5
6
Stop
1
2
13
Flow
3
Cold water
12
Important !
* All plumbing is to be installed in accordance with applicable codes and
regulations.
* Flush all water lines prior to making connection.
4
Cure Cap
Tile Surface
5
Sealing
INSTALL FAUCET
1. Installation
1,2
3
Cure Cap
Put a grain of sand to be fixed
Vinyl Cover
(1) Connect water supply line with faucet body(9). (Tighten the union nut.)
SAN-EI logo on the faucet bodys(9) should keep facing to inside bath tub.
(In case you install the opposite direction, faucet spout(13) can not be
installed.)
(2) Cure Cap should be covered until the tiles are laid. The cure cap indicates
the level where surface should be finished.
NOTE : Please pay attention the level indication whether finished surface is within
the mentioned level or not.
2. Inspection
After installing and connecting the faucet body(9), turn on supply valve to check
the water leakage.
SAN-EI Logo
3. Assemble parts
9
All thread portion, spindle portion should be covered or wrapped with such as
vinyl in advance.
4. Tile finishing
Please pay attention that the finished surface of tiling should be within the
mentioned level or not.
Upper
Level
NOTE : Please pay attention the installation, not to put sand or mortar into the
faucet body(9) or cure caps.
Bottom
Standard Level Level
5. Remove "cure caps" from the faucet body
6. Assemble handles and faucet spout
To protect water going to the cracked space of tiles, put the sealing material to
the cracked space. Then, assemble handles(3) and spout(13), referring to the
following indication. (Excess sealing should be removed perfectly.)
-4-
-5-
CARTRIDGE REPLACEMENT
OPERATION
Roman Tub Faucet
K917D-L-BW
Installation Dimension
Please kindly follow the installation dimension.
Improper installation may cause that water is
not coming out to the tub.
1
2
Spout 9-2/5"(240mm)
MIN 2"(50mm)
6
3
Rim Width
A
4
Spout 9-2/5"(240mm)
Rim Width
A
Below 2-4/5"(70mm)
Between 2"(50mm) to 5-3/10"(135mm)
3-1/2"(90mm)
3-9/10"(100mm)
Between 2"(50mm) to 4-1/2"(115mm)
Between 2"(50mm) to 3-1/10"(105mm)
4-7/10"(120mm)
Between 2"(50mm) to 3-3/10"(85mm)
5-1/2"(140mm)
Between 2"(50mm) to 2-3/5"(65mm)
6-1/10"(155mm)
Over 6-1/2"(165mm)
7
2"(50mm)
Can not be used.
1. Remove the top cap(1) from the handle(3) and loosen the screw(2) with
screw driver.
2. After removing the handle(3), loosen the handle escutcheon(4). (counter
clockwise) Also remove the seat packing(5).
3. Remove the spindle parts set(6) with pliers.
4. Remove an old rubber packing(7) with pliers and replace a new rubber packing(7).
5. To reassemble, reverse the previous steps.
4-3/10"(110mm)
2-9/10"(73mm)
2-9/10"(73mm)
Caution!:
Always turn water OFF before removing the cartridge. Open the handle to relieve
water pressure and ensure that water shut-off has been accomplished.
2-1/10"(53mm) 2-4/5"(70mm)
9-2/5"(240mm)
5
7-9/10"(200mm)
Please connect socket with union nut
onto supply pipe.
Then, the length between top surface
level and supply the level should keep
3-2/5"(88mm)
1/5"(5mm).
(Both supply line level should be the
same level each other.)
1/2-14 NPT
Tile Surface
3-2/5"(88mm)
1/5"(5mm)
Socket
Union
Nut
7-9
/10
"(2
00
mm
)
-6-
-3-
PARTS LIST
FLUSHING INSTRUCTIONS
The structure shown is an illustration.
Please use this structure for better understanding.
1
1
2
2
8
K917D-L-BW
3
General Description
1. Cap
2. Screw
3. Handle (Blue)
4. Handle Escutcheon
5. Seat packing
6. Click Cartridge Top Portion
7. Rubber Packing
8. Handle (Red)
9. Body
10. Socket
11. Union Nut
12. Seat Packing
13. Spout
14. Protection Top Cover
15. Protection Under Cover
16. Aerator
17. Rubber Packing
18. Net Filter
19. Aerator Body
4
5
13
14
6
12
IMPORTANT! : Pipe chips, sand, stones and other solid found in new and
renovated plumbing can damage the cealing of the cartridge and
cause leaks to avoid damage,
DO NOT TURN ON SUPPLY VALVES until instructed below.
1. After installing and connecting your new faucet, turn on in the full cold position
(handle pointing to the right) and turn on the cold supply for 15 seconds.
2. Loosen nut and remove supply lines Re-connect each supply lines into different
supply stop valves.(Excessive bending will cause leaking and damage to the
lines.) Then, tighten each of supply lines.
3. Close the handle, then using a towel unscrew the aerator from the end of the
spout and clean the aerator.
4. Using a towel replace the aerator and check the system for leaks.
TROUBLESHOOTING
TO CORRECT REVERSED HOT AND COLD POSITIONS :
1. Shut off both stop valves. Then, open faucet handles to relieve water pressure
that complete water shut-off has been accomplished.
2. Loosen nut and remove supply lines. Re-connect each supply lines into different
supply stop valves.(Excessive bending will cause leaking and damage to the
lines.) Then, tighten each of supply lines.
3. Re-installing and connecting, turn on both cold and hot supply.
4. Turn on in the full position, make sure that the each positions keeps correct way
& make sure any water leakage.
15
16
7
17
MAINTENANCE
Care and Cleaning of Chrome and Special Finishes
18
19
9
Do not use abrasive or chemical cleaners (including chlorine bleach) to clean faucets
as they may dull the luster and attack the chrome or special decorative finishes.
Use ONLY soap and water, then wipe dry with clean cloth or towel.
10
While cleaning the bathroom tile, the faucet should be protected from any splattering
of cleaner. Acids and cleaning fluids will discolor or remove chrome plating.
11
-2-
- 7-