Toyotomi TKN/TKG-671R32 Air Conditioners Owner Manual
PDF
Download
Document
Advertisement
Advertisement
User’s Manual Οδηγίες Χρήσης ΚΛΙΜΑΤΙΣΤΙΚΟ ΤΟΙΧΟΥ ΤΥΠΟΥ INVERTER WALL MOUNTED AIR CONDITIONER INVERTER TYPE MODELS/ΜΟΝΤΕΛΑ TKN/TKG-628R32 TKN/TKG-635R32 TKN/TKG-656R32 TKN/TKG-671R32 Thank you for purchasing our product. t Before using this product, be sure to read this Instruction Manual to ensure proper usage. Please keep this manual for later reference. t Improper use of this product may result in a malfunction, failure, unexpected accident, or create a potential hazard. Ευχαριστούμε για την επιλογής σας στο κλιματιστικό TOYOTOMI. Για τη σωστή του χρήση παρακαλούμε διαβάστε το εγχειρίδιο χρήσης προσεκτικά, πριν θέσετε τη μονάδα σε λειτουργία και κρατήστε το σε καλή κατάσταση για μελλοντική αναφορά. 2 GB Appliance filled with flammable gas R32. Before use the appliance, read the owner’s manual first. Before install the appliance, read the installation manual first. Before repair the appliance, read the service manual first. The Refrigerant To realize the function of the air conditioner unit, a special refrigerant circulates in the system. The used refrigerant is the fluoride R32, which is specially cleaned. The refrigerant is flammable and inodorous. Furthermore, it can leads to explosion under certain conditions. But the flammability of the refrigerant is very low. It can be ignited only by fire. Compared to common refrigerants, R32 is a nonpolluting refrigerant with no harm to the ozonosphere. The influence upon the greenhouse effect is also lower. R32 has got very good thermodynamic features which lead to a really high energy efficiency. The units therefore need a less filling. WARNING: Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacture. Should repair be necessary, contact your nearest authorized Service Centre. Any repairs carried out by unqualified personnel may be dangerous. The appliance shall be stored in a room without continuously operating ignition sources. (for example: open flames, an operating gas appliance or an operating electric heater.) Do not pierce or burn. Appliance shall be installed, operated and stored in a room with a floor area larger than 4m 2 . Appliance filled with flammable gas R32. For repairs, strictly follow manufacturer’s instructions only. Be aware that refrigrants not contain odour. Read specialist’s manual. 3 GB Precautions WARNING Operation and Maintenance This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory ormental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Do not connect air conditioner to multi-purpose socket. Otherwise, it may cause fire hazard. Do disconnect power supply when cleaning air conditioner. Otherwise, it may cause electric shock. . If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Do not wash the air conditioner with water to avoid electric shock. Do not spray water on indoor unit. It may cause electric shock or malfunction. After removing the filter, do not touch fins to avoid injury. Do not use fire or hair dryer to dry the filter to avoid deformation or fire hazard. 4 GB Precautions WARNING Maintenance must be performed by qualified professionals. Otherwise, it may cause personal injury or damage. Do not repair air conditioner by yourself. It may cause electric shock or damage. Please contact dealer when you need to repair air conditioner. Do not extend fingers or objects into air inlet or air outlet. It may cause personal injury or damage. Do not block air outlet or air inlet. It may cause malfunction. Do not spill water on the remote controller, otherwise the remote controller may be broken. When below phenomenon occurs, please turn off air conditioner and disconnect power immediately,and then contact the dealer or qualified professionals for service. Ɣ Power cord is overheating or damaged. Ɣ There’s abnormal sound during operation. Ɣ Circuit break trips off frequently. Ɣ Air conditioner gives off burning smell. Ɣ Indoor unit is leaking. If the air conditioner operates under abnormal conditions, it may cause malfunction,electric shock or fire hazard. When turning on or turning off the unit by emergency operation switch, please press this switch with an insulating object other than metal. Do not step on top panel of outdoor unit, or put heavy objects. It may cause damage or personal injury. 5 GB Precautions WARNING Attachment Installation must be performed by qualified professionals. Otherwise, it may cause personal injury or damage. Must follow the electric safety regulations when installing the unit. According to the local safety regulations, use qualified power supply circuit and circuit break. Do install the circuit break. If not, it may cause malfunction. An all-pole disconnection switch having a contact separation of at least 3mm in all poles should be connected in fixed wiring. Including an circuit break with suitable capacity, please note the following table.Air switch should be included magnet buckle and heating buckle function, it can protect the circuit-short and overload. Air Conditioner should be properly grounded. Incorrect grounding may cause electric shock. Don't use unqualified power cord. Make sure the power supply matches with the requirement of air conditioner.Unstable power supply or incorrect wiring or malfunction. Please install proper power supply cables before using the air conditioner. Properly connect the live wire, neutral wire and grounding wire of power socket. Be sure to cut off the power supply before proceeding any work related to electricity and safety. 6 GB Precautions WARNING Do not put through the power before finishing installation. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The temperature of refrigerant circuit will be high, please keep the interconnection cable away from the copper tube. The appliance shall be installed in accordance with national wiring regulations. Installation must be performed in accordance with the requirement of NEC and CEC by authorized personnel only The air conditioner is the first class electric appliance. It must be properly grounding with specialized grounding device by a professional. Please make sure it is always grounded effectively, otherwise it may cause electric shock. The yellow-green wire in air conditioner is grounding wire, which can't be used for other purposes. The grounding resistance should comply with national electric safety regulations. The appliance must be positioned so that the plug is accessible. All wires of indoor unit and outdoor unit should be connected by a professional. If the length of power connection wire is insufficient,please contact the supplier for a new one. Avoid extending the wire by yourself. 7 GB Precautions WARNING For the air conditioner with plug,the plug should be reachable after finishing installation For the air conditioner without plug, an circuit break must be installed in the line. If you need to relocate the air conditioner to another place, only the qualified person can perform the work. Otherwise, it may cause personal injury or damage. Select a location which is out of reach for children and far away from animals or plants.If it is unavoidable, please add the fence for safety purpose. The indoor unit should be installed close to the wall Instructions for installation and use of this product are provided by the manufacturer. 8 GB Precautions WARNING The air conditioner is not allowed to use in a room that has running fire (such as fire source, working coal gas ware, operating heater). It is not allowed to drill hole or burn the connection pipe. The air conditioner must be installed in a room that is larger than the minimum room area. The minimum room area is shown on the nameplate or following table a. Leak test is a must after installation. Instructions for installation and use of this product are provided by the manufacturer. Working temperature range Maximum cooling Maximum heating Indoor side DB/WB( 32/23 27/- ) Outdoor side DB/WB( 43/26 24/18 ) NOTICE: -15 ~ 43 ; for heat pump unit is - 15 9 ~ 43 . GB air inlet Connection wire air outlet 10 GB Buttons on remote controller ON/OFF button 2 MODE button 3 FAN button 4 TURBO button 5 ŸEXWWRQ 6 button 7 button Ÿ 1 1 3 8 SLEE P button 4 9 I FEEL button 5 10 TIMER ON / TIMER OFF button 9 11 CLOCK button 10 12 QUIE T button 11 12 13 X-FAN button 13 14 14 LIGHT button 15 16 15 2 6 7 8 button 16 TEMP button Introduction for icons on display screen I feel Quiet Set fan speed Turbo mode Send signal Healthy mode Scavenging functions 8ć heating function Operation mode Auto mode Cool mode Set temperature X-FAN function Dry mode Fan mode Heat mode Set time TIMER ON /TIMER OFF Clock Sleep mode Child lock Up & down swing Left & right swing Light Temp. display type :Indoor ambient temp. :Outdoor ambient temp. :Set temp. 11 GB Introduction for buttons on remote controller Note: Ɣ$IWHUSXWWLQJWKURXJKWKHSRZHUWKHDLUFRQGLWLRQHUZLOOJLYHRXWDVRXQG 2SHUDWLRQLQGLFWRULV21UHGLQGLFDWRU$IWHUWKDW\RXFDQRSHUDWHWKHDLU FRQGLWLRQHUE\XVLQJUHPRWHFRQWUROOHU Ɣ8QGHURQVWDWXVSUHVVLQJWKHEXWWRQRQWKHUHPRWHFRQWUROOHUWKHVLJQDOLFRQ RQWKHGLVSOD\RIUHPRWHFRQWUROOHUZLOOEOLQNRQFHDQGWKHDLUFRQGLWLRQHUZLOOJLYH RXWD³GH´VRXQGZKLFKPHDQVWKHVLJQDOKDVEHHQVHQWWRWKHDLUFRQGLWLRQHU 1 212))EXWWRQ 3UHVVWKLVEXWWRQFDQWXUQRQRUWXUQR WKHDLUFRQGLWLRQHU $IWHUWXUQLQJRQWKHDLU FRQGLWLRQHURSHUDWLRQLQGLFDWRURQLQGRRUXQLW¶VGLVSOD\LV21JUHHQLQGLFDWRU 7KHFRORXULVGL HUHQWIRUGL HUHQWPRGHOVDQGLQGRRUXQLWZLOOJLYHRXWDVRXQG 2 02'(EXWWRQ 3UHVVWKLVEXWWRQWRVHOHFW\RXUUHTXLUHGRSHUDWLRQPRGH $8T2 &22/ 'RY +(AT FAN Ɣ:KHQVHOHFWLQJDXWRPRGHDLUFRQGLWLRQHUZLOORSHUDWHDXWRPDWLFDOO\DFFRUGLQJ WRH[IDFWRU\VHWWLQJ6HWWHPSHUDWXUHFDQ¶WEHDGMXVWHGDQGZLOOQRWEHGLVSOD\HG DVZHOO3UHVVF$1EXWWRQFDQDGMXVWIDQVSHHG3UHVVEXWWRQFDQ DGMXVWIDQEORZLQJDQJOH Ɣ$IWHUVHOHFWLQJFRROPRGHDLUFRQGLWLRQHUZLOORSHUDWHXQGHUFRROPRGH&RRO LQGLFDWRURQLQGRRUXQLWLV213UHVVŸRUEXWWRQWRDGMXVWVHWWHPSH UDWXUH3UHVVF$1EXWWRQWRDGMXVWIDQVSHHG3UHVVEXWWRQWRDGMXVW IDQEORZLQJDQJOH Ɣ:KHQVHOHFWLQJGU\PRGHWKHDLUFRQGLWLRQHURSHUDWHVDWORZVSHHGXQGHUGU\ PRGH'U\LQGLFDWRURQLQGRRUXQLWLV218QGHUGU\PRGHIDQVSHHGFDQ¶W EHDGMXVWHG3UHVVEXWWRQWRDGMXVWIDQEORZLQJDQJOH Ɣ:KHQVHOHFWLQJIDQPRGHWKHDLUFRQGLWLRQHUZLOORQO\EORZIDQQRFRROLQJDQG QRKHDWLQJ$OOLQGLFDWRUVDUH2)F3UHVVF$1EXWWRQWRDGMXVWIDQVSHHG3UHVV EXWWRQWRDGMXVWIDQEORZLQJDQJOH Ɣ:KHQVHOHFWLQJKHDWLQJPRGHWKHDLUFRQGLWLRQHURSHUDWHVXQGHUKHDWPRGH +HDWLQGLFDWRURQLQGRRUXQLWLV213UHVVŸRUEXWWRQWRDGMXVWVHW WHPSHUDWXUH3UHVVF$1EXWWRQWRDGMXVWIDQVSHHG3UHVVEXWWRQWR DGMXVWIDQEORZLQJDQJOH&RROLQJRQO\XQLWZRQ¶WUHFHLYHKHDWLQJPRGHVLJQDO,I VHWWLQJKHDWPRGHZLWKUHPRWHFRQWUROOHUSUHVV212))EXWWRQFDQ¶WVWDUWXSWKH XQLW Ÿ Ÿ 12 GB Introduction for buttons on remote controller Note: Ɣ)RUSUHYHQWLQJFROGDLUDIWHUVWDUWLQJXSKHDWLQJPRGHLQGRRUXQLWZLOOGHOD\a PLQXWHVWREORZDLUDFWXDOGHOD\WLPHLV GHSHQGRQLQGRRUDPELHQWWHPSHUDWXUH Ɣ6HWWHPSHUDWXUHUDQJHIURPUHPRWHFRQWUROOHUać ) )DQVSHHGDXWRORZVSHHGPHGLXPVSHHGKLJKVSHHG 3 FAN button 3UHVsLnJ tKLV butt on FDQ sHWIDQ VSHHGFLUFuODUO\DVDXto A8TOOoZ PHGLuP KLJK Auto Note: Ɣ8QGHU $8T2VSHHGDLUFRQGLWLRQHUZLOO VHOHFWSURSHUIDQVSHHGDXWRPDWLFDOO\ DFFRUGLQJWRH[IDFWRU\VHWWLQJ Ɣ)DQVSHHGXQGHUGU\PRGHLVORZVSHHG 4 T8RBO butto n 8nGHU COOL oU HEAT PoGH pUHss tKLs button to tuUn to quLFk COOL oU quLFk HEATPRGHLFRQLVGLVSOD\HGRQUHPRWHFRQWUROOHU3UHVVWKLVEXWWRQDJDLQ WRH[LWWXUERIXQFWLRQDQGLFRQZLOOGLVDSSHDU ,I VWDUW WKLV IXQFWLRQ WKH XQLW ZLOO UXQ DW VXSHUKLJK IDQ VSHHGto FRRO RU KHDW TXLFNO\ VRWKDWWKHDPELHQWWHPSDSSURDFKVWKHSUHVHWWHPSDVVRRQDVSRVVLEOH Ÿ 5 ŸEXWWRQ Ÿ Ÿ Ɣ3UHVVŸRUEXWWRQRQFHLQFUHDVHRUGHFUHDVHVHWWHPSHUDWXUHć ) +ROGLQJŸRUEXWWRQVODWHUVHWWHPSHUDWXUHRQUHPRWHFRQWUROOHUZLOO WRURQLQGRRUXQLWZLOOFKDQJHDFFRUGLQJO\THPSHUDWXUHFDQ¶WEHDGMXVWHGXQGHU DXWRPRGH Ɣ:KHQVHWWLQJ 7,0(521 7,0(52))RU&/2&.SUHVVŸRUEXWWRQWR DGMXVWWLPH5HIHUWR&/2&. 7,0(521 7,0(52))EXWWRQV:KHQVHWWLQJ TIMER ON TIMER OFF oU CLOC. pUHss Ÿ oU button to DGMust tLPH RHIHU WR&/2&. 7,0(521 7,0(52))EXWWRQV Ÿ Ÿ 13 GB Introduction for buttons on remote controller EXWWRQQRWDYDLODEOH 6 3UHVVWKLVEXWWRQFDQVHOHFWOHIWULJKWVZLQJDQJOH)DQEORZDQJOHFDQEHVHOHFWHG FLUFXODUO\DVEHORZ QRGLVSOD\ (VWRSVDWFXUUHQWSRVLWLRQ Note: Ɣ3UHVVWKLVEXWWRQFRQWLQXRXVO\PRUHWKDQVWKHPDLQXQLWZLOOVZLQJEDFNDQG IRUWKIURPOHIWWRULJKWDQGWKHQORRVHQWKHEXWWRQWKHXQLWZLOOVWRSVZLQJLQJDQG SUHVHQWSRVLWLRQRIJXLGHORXYHUZLOOEHNHSWLPPHGLDWHO . \ Ɣ8QGHUVZLQJOHIWDQGULJKWPRGHZKHQWKHVWDWXVLVVZLWFKHGIURPRIIWRLI SUHVVWKLVEXWWRQDJDLQVODWHUVWDWXVZLOOVZLWFKWRR VWDWXVGLUHFWO\LISUHVV WKLVEXWWRQDJDLQZLWKLQVWKHFKDQJHRIVZLQJVWDWXVZLOODOVRGHSHQGRQWKH FLUFXODWLRQVHTXHQFHVWDWHGDERYH 7 EXWWRQ 3UHVVWKLVEXWW RQFDQVHOHFWXSGRZQVZLQJDQJOH)DQEORZDQJOHFDQEHVHOHFWHG FLUFXODUO\DVEHORZ QRGLVSOD\ KRUL]RQWDOORXYHUVVWRSV DWFXUUHQWSRVLWLRQ Ɣ:KHQVHOHFWLQJDLUFRQGLWLRQHULVEORZLQJIDQDXWRPDWLFDOO\+RUL]RQWDO ORXYHUZLOODXWRPDWLFDOO\VZLQJXSGRZQDWPD[LPXPDQJOH Ɣ:KHQVHOHFWLQJǃǃǃǃ Ɣ:KHQVHOHFWLQJǃǃ Ɣ+ROGEXWWRQDERYHVWRVHW\RXUUHTXLUHGVZLQJDQJOH:KHQUHDFKLQJ\RXU UHTXLUHGDQJOHUHOHDVHWKHEXWWRQ Note: ƔǃǃPD\QRWEHDYDLODEOH:KHQDLUFRQGLWLRQHUUHFHLYHVWKLVVLJQDOWKH DLUFRQGLWLRQHUZLOOEORZIDQDXWRPDWLFDOO\ . Ɣ3UHVVWKLVEXWWRQFRQWLQXRXVO\PRUHWKDQVWKHPDLQXQLWZLOOVZLQJEDFNDQG IRUWKIURPXSWRGRZQDQGWKHQORRVHQWKHEXWWRQWKHXQLWZLOOVWRSVZLQJLQJDQG SUHVHQWSRVLWLRQRIJXLGHORXYHUZLOOEHNHSWLPPHGLDWHO \ Ɣ8QGHUVZLQJXSDQGGRZQPRGHZKHQWKHVWDWXVLVVZLWFKHGIURPRIIWRLI SUHVVWKLVEXWWRQDJDLQVODWHUVWDWXVZLOOVZLWFKWRR VWDWXVGLUHFWO\LISUHVV 14 GB Introduction for buttons on remote controller this button again within 2s, the change of swing status will also depend on the circulation sequence stated above. 8 SLEEP button Under COOL, HEAT or DRY mode, press this button to start up sleep function. " " icon is displayed on remote controller. Press this button again to cancel sleep function and " " icon will disappear.After powered on, Sleep Off is defaulted. After the unit is turned off, the Sleep function is canceled. In this mode, the time of time can be adjusted. Under Fan and Auto modes, this function is not available. 9 I FEEL button Press this button to start I FEEL function and " " will be displayed on the remote controller. After this function is set, the remote controller will send the detected ambient temperature to the controller and the unit will automatically adjust the indoor temperature according to the detected temperature. Press this button again to close I FEEL function and " " will disappear. Ɣ3OHDVHSXWWKHUHPRWHFRQWUROOHUQHDUXVHUZKHQWKLVIXQFWLRQLVVHW'RQRWSXW the remote controller near the object of high temperature or low temperature in order to avoid detecting inaccurate ambient temperature. 10 TIMER ON / TIMER OFF button Ɣ TIMER ON button "TIMER ON" button can set the time for timer on. After pressing this button, " " LFRQGLVDSSHDUVDQGWKHZRUG21RQUHPRWHFRQWUROOHUEOLQNV3UHVVŸRU " "button to adjust TIMER ON setting. $IWHUHDFKSUHVVLQJŸRUEXWWRQ 7,0(521VHWWLQJZLOOLQFUHDVHRUGHFUHDVHPLQ+ROGŸRUEXWWRQV later, the time will change quickly until reaching your required time. Ÿ Ÿ Ÿ resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is started up, press "TIMER ON" button to cancel it. Ɣ TIMER OFF button "TIMER OFF" button can set the time for timer off. After pressing this button, " " LFRQGLVDSSHDUVDQGWKHZRUG2))RQUHPRWHFRQWUROOHUEOLQNV3UHVVŸRU " " button to adjust TIMER OFF setting. $IWHUHDFKSUHVVLQJŸRUEXWWRQ 7,0(52))VHWWLQJZLOOLQFUHDVHRUGHFUHDVHPLQ+ROGŸRUEXWWRQV later, the time will change quickly until reaching your required time. Press "TIMER OFF" word "OFF" will stop blinking. " " icon resumes displaying. Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press "TIMER OFF" button to cancel it. Ÿ Ÿ Ÿ 15 GB Introduction for buttons on remote controller Note: Ɣ8QGHURQDQGRff status, you can set TIMER OFF or TIMER ON simultaneously. Ɣ%HIRUHVHWWLQJ TIMER ON or TIMER OFF, please adjust the clock time. Ɣ After starting up TIMER ON or TIMER OFF, set the constant circulating valid. After that, air conditioner will be turned on or turned off according to setting time. ON/OFF button has no effect on setting. If you don’t need this function, please use remote controller to cancel it. 11 CLOCK button Press this button to set clock time. " " icon on remote controller will blink. Press ŸRUEXWWRQZLWKLQVWRVHWFORFNWiPH(DFKSUHVVLQJRIŸRUEXWWRQ clock time will increase or decrease 1 minXWH,IKROGŸRUEXWWRQVODWHU, time will change quickly. Release this button when reaching your required time. Ÿ Ÿ Ÿ Note: Ɣ&ORFNWLPHDGRSWVKRXUPRGH Ɣ The interval between two operation can¶WH[FHHGVV2WKHUZLVHUHPRWHFRQWUR ller will quit setting status. Operation for TIMER ON/TIMER OFF is the same. 12 QUIET button (not available) Press this button, the Quiet status is under the Auto Quiet mode (display " " and "AUTO" signal ) and Quiet mode (display " " singal) and Quiet OFF (there is no signal of " " displayed), after powered on, the Quiet OFF is defaulted. Note: Ɣ The Quiet function cannot be set up in Fan and Dry mode; Under the Quiet mode, the fan speed is not available. Ɣ,I Auto Quiet mode has been selected, after the room temperature reached the setting temperature or 10mins later, the AC will immediately enter into the Quiet running status, at this time the fan speed is not adjustable. 13 X-FAN button Pressing this button in COOL or DRY mode, the icon " " is displayed and the indoor fan will continue operation for 2 minutes in order to dry the indoor unit even though you have turned off the unit. After energization, X-FAN OFF is defaulted. X-FAN is not available in AUTO, FAN or HEAT mode. This function indicates that moisture on evaporator of indoor unit will be blowed after the unit is stopped to avoid mould. Ɣ+DYLQJVHW;FAN function on: After turning off the unit by pressing ON/OFF button indoor fan will continue running for about 2 min. at low speed. In this period, press X-FAN button to stop indoor fan directly. Ɣ+DYLQJVHW;FAN function off: After turning off the unit by pressing ON/OFF button, the complete unit will be off directly. 16 GB Introduction for buttons on remote controller 14 LIGHT button Press this button to turn off display light on indoor unit. " " icon on remote controller disappears. Press this button again to turn on display light. " " icon is displayed. 15 button Press this button to achieve the on and off of healthy and scavenging functions in LCD displays " ". Press the button for the second time to start healthy and scavenging functions simultaneously; LCD displays " " and " " . Press this button for the third time to quit healthy and scavenging functions simultaneously. Press the button for the fourth t ime to start healthy function; LCD display " " . Press this button again to repeat the operation above. 16 TEMP button By pressing this button, you can see indoor set temperature, indoor ambient temperature or outdoor ambient temperature on indoor unit’s display. The setting on remote controlleris selected circularly as below: no display Ɣ:KHQVHOHFWLQJRUQRGLVSOD\ZLWKUHPRWHFRQWUROOHr, temperature indicator on indoor unit displays set temperature. Ɣ:KHQVHOHFWLQJZLWKUHPRWHFRQWUROOHr, temperature indicator on indoor unit displays indoor ambient temperature. Ɣ:KHQVHOHFWLQJZLWKUHPRWHFRQWUROOHr, temperature indicator on indoor unit displays outdoor ambient temperature. (not available) Note: ƔOutdoor temperature display is not available for some models. At that time, indoor unit receives " " signal, while it displays indoor set temperature. Ɣ,W’s defaulted to display set temperature when turning on the unit.There is no display in the remote controller. Ɣ2QO\IRUWKHPRGHOVZKRVHLQGRRUXQLWKDVGXDOGLVSODy. Ɣ:KHQVHOHFWLQJGLVSOD\LQJRILQGRRURUoutdoor ambient temperature, indoor temperature indicator displays corresponding temperature and automatically turn 17 GB Function introduction for combination buttons Energy-saving function Under cooling mode, press "TEMP" and " CLOCK" buttons simultaneously to start up or turn off energy-saving function. When energy-saving function is started up, "SE" will be shown on remote controller, and air conditioner will adjust the set temperature automatically according to ex-factory setting to reach to the best energy-saving effect. Press "TEMP" and "CLOCK"buttons simultaneously again to exit energy-saving function. Note: Ɣ8QGHUHQHUJ\VDYLQJIXQFWLRQIDQVSHed is defaulted at auto speed and it can’t be adjusted. ƔUnder energy-saving function, set temperature can’t be adjusted. Press "TURBO" button and the remote controller won’t send signal. Ɣ6OHHSIXQFWLRQDQGHQHUJ\VDYLQJIXQFWion can’t operate at the same time. If energy-saving function has been set under cooling mode, press sleep button will cancel energy-saving function. If sleep function has been set under cooling mode, start up the energy-saving function will cancel sleep function. 8ć heating function Under heating mode, press "TEMP" and "CLOCK" buttons simultaneously to start up or turn off 8ć heating function. When this function is started up, " " and "8ć " will be shown on remote controller, and the air conditioner keep the heating status at 8ć . Press "TEMP" and "CLOCK" buttons simultaneously again to exit 8ć heating function. Note: Ɣ8QGHUć heating function, fan speed is defaulted at auto speed and it can’t be adjusted. Ɣ8QGHUć heating function, set temperature can’t be adjusted. Press "TURBO" button and the remote controller won’t send signal. Ɣ6OHHSIXQFWLRQDQGć heating function can’t operate at the same time. If 8ć heating function has been set under cooling mode, press sleep button will cancel 8ć heating function. If sleep function has been set under cooling mode, start up the 8ć heating function will cancel sleep function. Ɣ8QGHU̧ temperature display, the remote controller will display 46 ̧ heating. Child lock function Ÿ 3UHVVŸDQGVLPXOWDQHRXVO\WRWXUQRQRUWXUQRff child lock function. When child lock function is on, " " icon is displayed on remote controller. If you operate the remote controller, the " " icon will blink three times without sending signal to the unit. Temperature display switchover function Ÿ Under OFF status, press " " and "MODE" buttons simultaneously to switch temperature display between ć and ̧ . 18 GB Operation guide 1. After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner. 2. Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN, HEAT. 3UHVVŸRUEXWWRQWRVHW\RXUUHTXLUHGWHPSHUDWXUH7emperature can’t 3. be adjusted under auto mode). 4. Press "FAN" button to set your required fan speed: auto, low, medium and high speed. 5. Press "SWING" button to select fan blowing angle. Ÿ Replacement of batteries in remote controller 1. Press the back side of remote controller marked the cover of battery box along the arrow direction. 5HSODFHWZR$$A 1.5V) dry batteries, and make sure the position of "+" polar and "-" polar are correct. 3. Reinstall the cover of battery box. signal sender battery reinstall remove Cover of battery box NOTICE Ɣ'XULQJRSHUDWLRQSRLQWWKHUHPRWHFRQWUROVLJQDOVHQGHUDWWKHUHFHLYLQJ window on indoor unit. Ɣ The distance between signal sender and receiving window should be no more than 8m, and there should be no obstacles between them. or wireless telephone; remote controller should be close to indoor unit during operation. Ɣ5HSODFHQHZEDWWHULHVRIWKHVDPHPRGHOZKHQUHSODFHPHQWLVUHTXLUHG Ɣ:KHQ\RXGRQ¶WXVHUHPRWHFRQWUROOHUIRUDORQJWLPHSOHDVHWDNHRXWWKH batteries. Ɣ,IWKHGLVSOD\RQUHPRWHFRQWUROOHULVIX]]\RUWKHUH’s no display, please replace batteries. 19 GB Emergency operation If remote controller is lost or damaged, please use auxiliary button to turn on or turn off the air conditioner. The operation in details are as below: air conditioner. When the air conditioner is turned on, it will operate under auto mode. panel aux. button WARNING: Use insulated object to press the auto button Clean and maintenance WARNING Ŷ Turn off the air conditioner and disconnect the power before cleaning the air conditioner to avoid electric shock. Ŷ'RQRWZDVKWKHDLUFRQGLWLRQHUZLWKZDWHUWRDYRLGHOHFWULFVKRFN Ŷ'RQRWXVHYRODWLOHOLTXLGWRFOHDQWKHDLUFRQGLWLRQHr. Clean surface of indoor unit When the surface of indoor unit is dirty, it is recommended to use a soft dry cloth or wet cloth to wipe it. NOTICE: Ɣ'RQRWUHPRYHWKHSDQHOZKHQFOHDQLQJLW 20 GB Clean and Maintenance 1 3 Open panel Ɣ Use dust catcher or water to clean the filter. Ɣ When the filter is very dirty, use the water (below 45 ) to clean it, and then put it in a shady and cool place to dry. Pull out the panel to a certain angle as shown in the fig. 2 Remove the filter as indicated in the fig. 4 Install the filter and then close the panel cover tightly. Ŷ The filter should be cleaned every three months. If there is much dust in the operation environment, clean frequency can be increased. Ŷ After removing the filter, do not touch fins to avoid injury. Ŷ Do not use fire or hair dryer to dry the filter to avoid deformation or fire hazard. 21 GB Clean and Maintenance 1. Check whether air inlets and air outlets are blocked. 2. Check whether air switch, plug and socket are in good condition. 3. Check whether filter is clean. 4. Check whether mounting bracket for outdoor unit is damaged or corroded. If yes, please contact dealer. 5. Check whether drainage pipe is damaged. 1. Disconnect power supply. 2. Clean filter and indoor unit’s panel. 3. Check whether mounting bracket for outdoor unit is damaged or corroded. If yes, please contact dealer. Notice for recovery 1. Many packing materials are recyclable materials. Please dispose them in appropriate recycling unit. 2. If you want to dispose the air conditioner, please contact local dealer or consultant service center for the correct disposal method. 22 GB Malfunction analysis General phenomenon analysis Please check below items before asking for maintenance. If the malfunction still can’t be eliminated, please contact local dealer or qualified professionals. Phenomenon Check items Solution Ɣ Whether it's interfered severely Ɣ Pull out the plug. Reinsert (such as static electricity,stable the plug after about 3min, and voltage)? then turn on the unit again. Indoor unit can’t receive remote controller’s signal or remote controller has no action. Ɣ Whether remote controller is within the signal receiving range? Ɣ Signal receiving range is 8m. Ɣ Whether there are obstacles? Ɣ Remove obstacles. Ɣ Select proper angle and point Ɣ Whether remote controller is pointing at the receiving the remote controller at the rewindow? ceiving window on indoor unit. Ɣ Is sensitivity of remote contro- Ɣ Check the batteries. If the ller low; fuzzy display and no power of batteries is too low, display? please replace them. Ɣ Check whether remote contƔ No display when operating roller appears to be damaged. remote controller? If yes, replace it. Ɣ Fluorescent lamp in room? No air emitted from indoor unit Ɣ Take the remote controller close to indoor unit. Ɣ Turn off the fluoresent lamp and then try it again. Ɣ Air inlet or air outlet of indoor unit is blocked? Ɣ Eliminate obstacles. Ɣ Under heating mode, indoor temperature is reached to set temperature? Ɣ After reaching to set temperature, indoor unit will stop blowing out air. Ɣ Heating mode is turned on just Ɣ In order to prevent blowing now? out cold air, indoor unit will be started after delaying for several minutes, which is a normal phenomenon. 23 GB Malfunction analysis Phenomenon Air conditioner can’t operate Mist is emitted from indoor unit’s air outlet Set temperature can’t be adjusted Cooling (heating) effect is not good. Check items Solution Ɣ Power failure? Ɣ Wait until power recovery. Ɣ Is plug loose? Ɣ Reinsert the plug. Ɣ Air switch trips off or fuse is burnt out? Ɣ Ask professional to replace air switch or fuse. Ɣ Wiring has malfunction? Ɣ Ask professional to replace it. Ɣ Unit has restarted immediately Ɣ Wait for 3min, and then turn after stopping operation? on the unit again. Ɣ Whether the function setting for remote controller is correct? Ɣ Reset the function. Ɣ Indoor temperature and humidity is high? Ɣ Because indoor air is cooled rapidly. After a while, indoor temperature and humidity will be decrease and mist will disappear. Ɣ Unit is operating under auto mode? Ɣ Temperature can’t be adjusted under auto mode. Please switch the operation mode if you need to adjust temperature. Ɣ Your required temperature exceeds the set temperature range? Ɣ Set temperature range: 16 ~30 . Ɣ Voltage is too low? Ɣ Wait until the voltage resumes normal. Ɣ Filter is dirty? Ɣ Clean the filter. Ɣ Set temperature is in proper range? Ɣ Adjust temperature to proper range. Ɣ Door and window are open? Ɣ Close door and window. 24 GB Malfunction analysis Phenomenon Odours are emitted Check items Solution Ɣ Whether there’s odour source, Ɣ Eliminate the odour source. such as furniture and cigarette, Ɣ Clean the filter. etc. Air conditioner Ɣ Whether there’s interference, operates norsuch as thunder, wireless mally suddenly devices, etc. Ɣ Disconnect power, put back power, and then turn on the unit again. Outdoor unit has vapor Ɣ Heating mode is turned on? Ɣ During defrosting under heating mode, it may generate vapor, which is a normal phenomenon. “Water flowing” noise Ɣ Air conditioner is turned on or turned off just now? Ɣ The noise is the sound of refrigerant flowing inside the unit, which is a normal phenomenon. Cracking noise Ɣ Air conditioner is turned on or turned off just now? 25 Ɣ This is the sound of friction caused by expansion and/or contraction of panel or other parts due to the change of temperature. GB Malfunction analysis Error Code Ɣ When air conditioner status is abnormal, temperature indicator on indoor unit will blink to display corresponding error code. Please refer to below list for identification of error code. Error code E5 E8 U8 H6 Troubleshooting It can be eliminated after restarting the unit. If not , please It can be eliminated after restarting the unit. If not,please It can be eliminated after restarting the unit. If not,please It can be eliminated after restarting the unit. If not,please C5 F1 F2 H3 F4 F0 Note: If there're other error codes, please contact qualified professionals for service. Ŷ When below phenomenon occurs, please turn off air conditioner and disconfor service. Ɣ Power cord is overheating or damaged. Ɣ There’s abnormal sound during operation. Ɣ Air switch trips off frequently. Ɣ Air conditioner gives off burning smell. Ɣ Indoor unit is leaking. Ŷ If the air conditioner operates under abnormal conditions, it may cause 26 GB Installation dimension diagram 27 GB Tools for installation 1 Level meter 2 Screw driver 3 Impact drill 4 Drill head 5 Pipe expander 6 Torque wrench 7 Open-end wrench 8 Pipe cutter 9 Leakage detector 10 Vacuum pump 11 Pressure meter 12 Universal meter 13 Inner hexagon spanner Note: 14 Measuring tape Ɣ Please contact the local agent for installation. Ɣ Don't use unqualified power cord. Selection of installation location Basic requirement Installing the unit in the following places may cause malfunction. If it is unavoidable, please consult the local dealer: 1.The place with strong heat sources, , or volatile objects spread in the air. 2.The place with high-frequency devices (such as welding machine, medical equipment). 3.The place near coast area. 4.The place with oil or fumes in the air. 5.The place with sulfureted gas. 6.Other places with special circumstances. 7.The appliance shall not be installed in the laundry. Indoor unit 1. There should be no obstruction near air inlet and air outlet. 2. Select a location where the condensation water can be dispersed easily and won't affect other people. 3. Select a location which is convenient to connect the outdoor unit and near the power socket. 4. Select a location which is out of reach for children. 5. The location should be able to with stand the weight of indoor unit and won't increase noise and vibration. 6. The appliance must be installed 2.5m 7. Don't install the indoor unit right above the electric appliance. 8. Please try your best to keep way from fluorescent lamp. Outdoor unit will not affect neighborhood. 2. The location should be well ventilated and dry, in which the outdoor unit won't be exposed directly to sunlight or strong wind. 3. The location should be able to withstand the weight of outdoor unit. 4. Make sure that the installation follows the requirement of installation dimension diagram. 5. Select a location which is out of reach for children and far away from animals or plants.If it is unavoidable, please add the fence for safety purpose. 28 GB Requirements for electric connection Safety precaution 1. Must follow the electric safety regulations when installing the unit. 2. According to the local safety regulations, use qualified power supply circuit and air switch. 3. Make sure the power supply matches with the requirement of air conditioner. Unstable power supply or incorrect wiring or malfunction. Please install proper power supply cables before using the air conditioner. 4. Properly connect the live wire, neutral wire and grounding wire of power socket. 5. Be sure to cut off the power supply before proceeding any work related to electricity and safety. 6. Do not put through the power before finishing installation. 7. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 8. The temperature of refrigerant circuit will be high, please keep the interconnection cable away from the copper tube. 9. The appliance shall be installed in accordance with national wiring regulations. 10. Appliance shall be installed, operated and stored in a room with a floor area larger than 4m 2 . Please notice that the unit is filled with flammable gas R32. Inappropriate treatment of the unit involves the risk of severe damages of people and material. Details to this refrigerant are found in chapter “refrigerant”. Grounding requirement 1. The air conditioner is the first class electric appliance. It must be properly grounding with specialized grounding device by a professional. Please make sure it is always grounded effectively, otherwise it may cause electric shock. 2. The yellow-green wire in air conditioner is grounding wire, which can't be used for other purposes. 3. The grounding resistance should comply with national electric safety regulations. 4. The appliance must be positioned so that the plug is accessible. 5. An all-pole disconnection switch having a contact separation of at least 3mm in all poles should be connected in fixed wiring. 6. Including an air switch with suitable capacity, please note the following table. Air switch should be included magnet buckle and heating buckle function, it can protect the circuit-short and overload. (Caution: please do not use the fuse only for protect the circuit) Air-conditioner Air switch capacity 9K & 12K 10A 18K 16A 24K 25A 29 GB 9&12k Wall Level meter Mark in the middle of it Space to the wall above 150mm Wall Space to the wall above 150mm Right Left Rear piping hole Rear piping hole 18k Wall Mark in the middle of it Space to the wall above 150mm Left Rear piping hole 24k Level meter Wall Wall Mark in the middle of it Space to the wall above 150mm Space to the wall above 150mm Left Right Rear piping hole Rear piping hole Level meter Wall Space to the wall above 150mm Right Rear piping hole ĭ55 or ĭ70 on the selected outlet pipe downward to the outdoor side with the gradient of 5-10°. 30 GB Ɣ Pay attention to dust prevention and take relevant safety measures when ĭ55/ ĭ70 Ɣ not provided and should be bought 31 GB Installation of indoor unit open-end wrench union nut torque wrench pipe Hex nut diameter Tightening torque (N.m) ĭ6 15~20 ĭ 9.52 30~40 ĭ 12 45~55 ĭ 16 60~65 ĭ 19 70~75 indoor pipe 4. Wrap the indoor pipe and joint of connection pipe with insulating pipe, and then wrap it with tape. insulating pipe Step six: install drain hose 1. Connect the drain hose to the outlet pipe of indoor unit. drain hose outlet pipe 2. Bind the joint with tape. drain hose outlet pipe tape drain hose Note: Ɣ Add insulating pipe in the indoor drain hose in order to prevent condensation. Ɣ The plastic expansion particles are not provided. insulating pipe Step seven: connect wire of indoor unit panel screw 1. Open the panel, remove the screw on the wiring cover and then take down the cover. wiring cover 32 GB of indoor unit and then pull it out from 3. Remove the wire clip; connect the power connection wire to the wiring terminal according to the color; tighten the screw 09、12K、18K、24K Heat pump type: N(1) 2 3 blue black brown yellowgreen Outdoor unit connection Note: The wiring board is for reference only. Please refer to the actual one. Ɣ Ɣ For the air conditioner without plug, an air switch must be installed in the line. be more than 3mm. 33 GB Installation of indoor unit Step eight: bind up pipe 1. Bind up the connection pipe, power cord and drain hose with the band. connection pipe drain hose band indoor and outdoor power cord indoor unit gas pipe indoor power cord liquid pipe 3. Bind them evenly. 4. The liquid pipe and gas pipe should be bound separately at the end. band drain hose 2. Reserve a certain length of drain hose and power cord for installation when binding them. When binding to a certain degree, separate the indoor power and then separate the drain hose. Note: Ɣ The power cord and control wire can't be crossed or winding. Ɣ The drain hose should be bound at the bottom. Step nine: hang the indoor unit 1. Put the bound pipes in the wall pipe and then make them pass through the wall hole. 2. Hang the indoor unit on the wall-mounting frame. 3. Stuff the gap between pipes and wall hole with sealing gum. 4. Fix the wall pipe. 5. Check if the indoor unit is installed firmly and closed to the wall. indoor wall pipe upper hook outdoor sealing gum lower hook of wall-mounting frame Note: Ɣ Do not bend the drain hose too excessively in order to prevent blocking. 34 GB Ɣ 5m, 7.5m, 8m. 2.Min. length of connection pipe is 3m. 3.Max. length of connection pipe capacity capacity 5000Btu/h (1465W) 15 24000Btu/h (7032W) 25 7000Btu/h (2051W) 15 28000Btu/h (8204W) 30 9000Btu/h (2637W) 15 36000Btu/h (10548W) 30 42000Btu/h (12306W) 30 48000Btu/h (14064W) 30 12000Btu/h (3516W) 18000Btu/h (5274W) 25 Ɣ After the length of connection pipe is prolonged for 10m at the basis of standard length, you should add 5ml of refrigerant oil for each additional 5m m am b Ɣ Additional refrigerant charging amount additional refrigerant charging amount per meter Ɣ Basing on the length of standard pipe, add refrigerant according to the requirement as shown in the table. The additional refrigerant charging amount per meter is di ferent according to the diameter of liquid pipe. See the 35 GB Configuration of connection pipe Sheet 2. Additional refrigerant charging amount for R32 Diameter of connection pipe mm Indoor unit throttle Liquid pipe Gas pipe Outdoor unit throttle Cooling only, Cooling only cooling and heating cooling and heating (g / m) (g / m) (g / m) _ _ Note: The additional refrigerant charging amount in Sheet 2 is recommended value, not compulsory. 36 GB Safety operation of flammable refrigerant Qualification requirement for installation and maintenance man All the work men who are engaging in the refrigeration system should bear the valid certification awarded by the authoritative organization and the qualification for dealing with the refrigeration system recognized by this industry. If it needs other technician to maintain and repair the appliance, they should be supervised by the person who bears the qualification for using the flammable refrigerant. It can only be repaired by the method suggested by the equipment’s manufacturer. Installation notes The air conditioner is not allowed to use in a room that has running fire (such as fire source, working coal gas ware, operating heater). It is not allowed to drill hole or burn the connection pipe. The air conditioner must be installed in a room that is larger than the minimum room area. The minimum room area is shown on the nameplate or following table a. Leak test is a must after installation. table a - Minimum room area ( m 2 ) Charge amount (kg) floor location Minimum room window mounted area( m 2 ) wall mounted ceiling mounted / / / / Maintenance notes Check whether the maintenance area or the room area meet the requirement of the nameplate. - It’s only allowed to be operated in the rooms that meet the requirement of the nameplate. Check whether the maintenance area is well-ventilated. - The continuous ventilation status should be kept during the operation process. Check whether there is fire source or potential fire source in the maintenance area. - The naked flame is prohibited in the maintenance area; and the “no smoking” warning board should be hanged. Check whether the appliance mark is in good condition. - Replace the vague or damaged warning mark. Welding If you should cut or weld the refrigerant system pipes in the process of maintaining, please follow the steps as below: 37 GB Safety operation of flammable refrigerant a. Shut down the unit and cut power supply b. Eliminate the refrigerant c. Vacuuming d. Clean it with N2 gas e. Cutting or welding f. Carry back to the service spot for welding The refrigerant should be recycled into the specialized storage tank. Make sure that there isn’t any naked flame near the outlet of the vacuum pump and it’s well-ventilated. Filling the refrigerant Use the refrigerant filling appliances specialized for R32. Make sure that different kinds of refrigerant won’t contaminate with each other. The refrigerant tank should be kept upright at the time of filling refrigerant. Stick the label on the system after filling is finished (or haven’t finished). Don’t overfilling. After filling is finished, please do the leakage detection before test running; another time of leak detection should be done when it’s removed. Safety instructions for transportation and storage Please use the flammable gas detector to check before unload and open the container. No fire source and smoking. According to the local rules and laws. 38 GB Installation of outdoor unit (select it according to the actual installation situation) 1. Select installation location according to the house structure. 2. Fix the support of outdoor unit on the selected location with expansion screws. installing the outdoor unit. ƔMake sure the support can withstand at least four times of the unit weight. Ɣ7KHRXWGRRUXQLWVKRXOGEHLQVWDOOHGDWOHDVW joint. Ɣ)RUWKHXQLWZLWKFRROLQJFDSDFLW\RI: ~5000W, 6 expansion screws are needed; for the unit with cooling capacity of 6000W ~8000W, 8 expansion screws are needed; for the unit with cooling capacity of 10000W ~16000W, 10 expansion screws are needed. Step two: install drain joint (Only for cooling and heating unit) 1. Place the outdoor unit on the support. 2. Fix the foot holes of outdoor unit with bolts. 1. Connect the outdoor drain joint into the hole on the chassis, as shown in the picture below. 2. Connect the drain hose into the drain vent. drain vent Drain hose DWOHDVWFPDERYHWKHIORRU foot holes chassis outdoor drain joint foot holes 39 6 GB Installation of outdoor unit Step four: connect indoor and outdoor pipes 1. Remove the screw on the right handle of outdoor unit and then remove the handle. 3. Pretightening the union nut with hand. pipe joint screw union nut handle 2. Remove the screw cap of valve and aim the pipe joint at the bellmouth of pipe. 4. Tighten the union nut with torque wrench by referring to the sheet below. torque Hex nut diameter Tightening (N.m) ĭ a ĭ 30~40 ĭ a ĭ a ĭ a liquid pipe liquid valve gas pipe gas valve 1. Remove the wire clip; connect the power connection wire and signal control wire (only for cooling and heating unit) to the wiring terminal according to the 、12K Heat pump type: N(1) N 2 18 、24K Heat pump type: N(1) 3 L yellowgreen blue black brown yellowgreen blue brown (black) N Indoor unit connection 2 3 blue black brown L N brown blue (black) yellowgreen yellowgreen L POWER L Indoor unit connection N POWER Note: The wiring board is for reference only. Please refer to the actual one. 40 GB Installation of outdoor unit 2. Fix the power connection wire and signal control wire with wire clip (only for cooling and heating unit). Note: Step six: neaten the pipes 1. The pipes should be placed along the wall, bent reasonably and hidden possibly. Min. semidiameter of bending the pipe is 10cm. 2. If the outdoor unit is higher than the wall hole, you must set a U-shaped curve in the pipe before pipe goes into the room, in order to prevent rain from getting into the room. wall U-shaped curve drain hose Note: nwards. The drain hose can't be shouldn't be higher than the outlet pipe hole of indoor unit. the drain hose can't raise upwards. The drain hose can't be fluctuant in water in order to drain smoothly. The drain hose can't be fluctuant The water outlet can't be fluctuant The water outlet can't be placed in water 41 GB Vacuum pumping Use vacuum pump 1. Remove the valve caps on liquid valve the liquid valve and gas piezometer Lo Hi valve and the nut of refrigas valve gerant charging vent. refrigerant charging valve cap 2. Connect the charging hose of piezometer to the refri- vent gerant charging vent of gas nut of refrigerant valve and then connect the charging vent other charging hose to the vacuum pump vacuum pump. 3. Open the piezometer cominner hexagon pletely and operate for spanner 10-15min to check if the pressure of piezometer remains in -0.1MPa. close 4. Close the vacuum pump open and maintain this status for 1-2min to check if the pressure of piezometer remains in -0.1MPa. If the pressure decreases, there may be leakage. 5. Remove the piezometer, open the valve core of liquid valve and gas valve completely with inner hexagon spanner. 6. Tighten the screw caps of valves and refrigerant charging vent. 7. Reinstall the handle. Leakage detection 1. With leakage detector: Check if there is leakage with leakage detector. 2. With soap water: If leakage detector is not available, please use soap water for leakage detection. Apply soap water at the suspected position and keep the soap water for more than 3min. If there are air bubbles coming out of this position, there's a leakage. 42 GB Check after installation Ɣ Check according to the following requirement after finishing installation. Items to be checked Possible malfunction Has the unit been installed rmly? The unit may drop, shake or emit noise. Have you done the refrigerant leakage test? It may cause insuf cient cooling (heating) capacity. Is heat insulation of pipeline suf cient? It may cause condensation and water dripping. Is water drained well? It may cause condensation and water dripping. Is the voltage of power supply according to the voltage marked on the nameplate? It may cause malfunction or damaging the parts. Is electric wiring and pipeline installed correctly? It may cause malfunction or damaging the parts. Is the unit grounded securely? It may cause electric leakage. Does the power cord follow the specication? It may cause malfunction or damaging the parts. Is there any obstruction in the air inlet and outlet? It may cause insuf cient cooling (heating) capacity. The dust and sundries caused during installation are removed? It may cause malfunction or damaging the parts. The gas valve and liquid valve of connection pipe are open completely? Is the inlet and outlet of piping hole been covered? It may cause insuf cient cooling (heating) capacity. It may cause insufficient cooling (heating) capacity or waster eletricity. Test operation 1. Preparation of test operation Ɣ Specify the important notes for air conditioner to the client. 2. Method of test operation Ɣ Put through the power, press ON/OFF button on the remote controller to start operation. Ɣ Press MODE button to select AUTO, COOL, DRY, FAN and HEAT to check whether the operation is normal or not. Ɣ If the ambient temperature is lower than 16 , the air conditioner can’t start cooling. 43 GB Pipe expanding method Note: Improper pipe expanding is the main cause of refrigerant leakage. Please expand the pipe according to the following steps: A: Cut the pipe E: Expand the port Ɣ([SDQGWKHSRUWZLWKH[SDQGHr. the distance of indoor unit and outdoor unit. Ɣ&XWWKHUHTXLUHGSLSHZLWKSLSHFXWWHr. hard mold expander pipe pipe pipe cutter leaning uneven Note: Ɣ$LVGLfferent according to the diameter, please refer to the sheet below: burr B: Remove the burrs Ɣ5HPRYHWKHEXUUVZLWKVKDSHUDQG prevent the burrs from getting into the pipe. pipe shaper downwards C: Put on suitable insulating pipe D: Put on the union nut Ɣ5HPRYHWKHXQLRQQXWRQWKHLQGRRU connection pipe and outdoor valve; install the union nut on the pipe. Max Min ĭ ĭ ĭ ĭ F: Inspection Ɣ&KHFNWKHTXDOLW\RIH[SDQGLQJSRUW ,IWKHUHLVDQ\EOHPLVKH[SDQGWKH port again according to the steps above. smooth surface improper expanding union pipe leaning pipe A(mm) Outer diameter (mm) damaged surface crack uneven thickness WKHOHQJWKLVHTXDl 44 GR GB Εισαγωγέας: Γ.Ε.ΔΗΜΗΤΡΙΟΥ Α.Ε.Ε. Λεωφόρος Κηφισού 6, Αιγάλεω, 122 42, Αθήνα Τηλέφωνο: 210 53 86 400 SERVICE - ΑΝΤΑΛΛΑΚΤΙΚΑ Γ.Ε.ΔΗΜΗΤΡΙΟΥ Α.Ε.Ε. Λεωφόρος Κηφισού 6, Αιγάλεω, 122 42, Αθήνα Τηλέφωνο: 210 53 86 490 Φαξ: 210 53 13 349 G.E.D. Toyotomi Italia S.r.l. Εmail: [email protected] www.toyotomi.it ">

Public link updated
The public link to your chat has been updated.
Advertisement