9' Warm White /Multi LED Color Changing
One Plug Tree V66362-60
INSTRUCTION MANUAL
Thank you for purchasing a SYLVANIA™ Pre-lighted Tree. This tree assembles in minutes
and is decorated with energy saving LED light sets. This tree has 8 lighting options, Steady
Warm White, Flashing Warm White, Slow Fade Warm White, Steady Multicolor, Flashing
Multicolor, Slow Fade Multicolor, Sequential Multicolor & Warm White, Slow Fade
Multicolor & Warm White. These functions can be changed by using the foot pedal. Please
refer to Step 10 of the assembly instructions.
FOR INDOOR/SEASONAL USE ONLY
This tree has been carefully constructed to insure many years of safe, seasonal use. In the
unlikely event that you experience problems with the tree please call our customer service
hotline at (800) 414-3434. Agents are on call 24/7 to answer your questions. Do not return
this tree to the place of purchase. Please provide the item number of the product purchased as
well as information pertaining to the nature and description of the problem. The item number
for your tree is shown above and can also be found below the UPC sticker on the tree box and
also on a sticker placed on the trunk of the tree, right above where the trunk enters the tree
stand. Please have this number available before you call. Please do not remove this
identification sticker.
This product carries a 3 year limited guarantee. This guarantee does not cover damage
resulting from accident, misuse, abuse, negligence, or normal wear and any discoloration.
The warranty is in force from the date that you purchased this tree. There is no need to
register your purchase, however it is most important that you retain original sales receipt as
proof of purchase. Receipt may be required for warranty service. Please note this warranty is
non-transferable and is voided if the product is not used as intended. Please keep this product
manual for future reference.
This 9’ tree is pre-strung with 1000 3.0 volt, 0.06 watt LED lights:
CARTON INCLUDES:
 4 Pre-lighted tree sections (A-Top Section, B – Upper Middle Section, C –Lower
Middle Section, and D - Bottom Section.)
 1 Sturdy metal tree stand
 1 Screw for tree stand
 1 power supply cord with foot pedal switch
 8 extra 3.0 V replacement bulbs
 2 spare replacement fuse (3 A) for power supply cord plug
CAUTION! – ALWAYS UNPLUG YOUR TREE FROM
ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
ASSEMBLY:
Note: Before you start to assemble your tree please choose a location near an electrical wall outlet. Place the
tree stand on a level surface.
Please remove protective covers from the base of the pole for each tree section before assembling.
1. Unfold the tree stand and insert the screw into the hole.
2. Carefully insert the bottom section (D) of the tree into the tree stand and tighten the screw. (See Fig. 1)
3. Insert the lower middle section (C) of the tree into the bottom section (D). Rotate the lower middle section
(C) right or left until it falls into place, then insert vertically and tightly into the bottom section (D) to
ensure proper circuit connection. (See Fig. 2)
4. Insert the upper middle section (B) of the tree into the lower middle section (C). Rotate the upper middle
section (B) right or left until it falls into place, then insert vertically and tightly into the lower bottom
section (C) to ensure proper circuit connection. (See Fig. 3)
5. Insert the top section (A) into the upper middle section (B). Rotate the top section (A) right or left until it
falls into place, then insert vertically and tightly into the upper middle section (B) to ensure proper circuit
connection. (See Fig. 4)
Note: There is a tree top connector on the top section (A).
6. Connect the end connector of power cord (E) with the connector found on the bottom section (D). It is
important that this connection is made in correct direction (always match the protuberance of the end
connector of power cord to the concave of the connector found on the bottom section (D) according to the
magnified drawing on fig. 5.
7. Plug well-connected power supply cord from bottom section (D) into electrical outlet. (See Fig. 8)
8. Unplug the cord when not in use.
9. For your convenience, it is equipped with a foot pedal switch for choosing different functions.
10. This tree is Color Changing.
1) Press the foot switch for less than two seconds to select from the 8 lighting functions listed below:
i. Steady Warm White
ii. Flashing Warm White
iii. Slow Fade Warm White
iv. Steady Multicolor
v. Flashing Multicolor
vi. Slow Fade Multicolor
vii. Sequential Multicolor & Warm White
viii. Slow Fade Multicolor & Warm White
2) Press the foot switch for more than two seconds to select below timer hours:
i. Indicator lights on foot switch turn on red:
The tree lights will automatically run through a 6-hours ON, 18-hours OFF cycle.
ii. Indicator lights on foot switch turn on green:
The tree lights will automatically run through an 8-hours ON, 16-hours OFF cycle.
iii. Indicator lights on foot switch turn on blue:
The tree lights will automatically run through a 2-hours ON, 22-hours OFF cycle.
iv. Indicator lights on foot switch turn on yellow:
The tree lights will automatically run through a 4-hours ON, 20-hours OFF cycle.
TREE SHAPING:
1. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be
sure that all wires are free of branch hinges as illustrated in Figure 6.
2. Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left
and one at the center of the main stem as illustrated in Figure 7. Repeat pattern for each branch.
TROUBLE SHOOTING:
1. If entire tree does not light, make sure power supply cord plug is securely inserted into a working
electrical outlet.
2. If an entire section of the tree does not light:
a. Check to be sure that all sections of the tree are securely connected.
b. Check fuse in the power supply cord and replace if necessary.
3. If you are still experiencing problems with the tree please call 1-800-414-3434 for instructions.
CAUTION! – ALWAYS UNPLUG YOUR TREE FROM
ITS POWER SOURCE BEFORE ATTEMPTING
EITHER FUSE OR BULB REPLACEMENT.
FUSE REPLACEMENT:
A) Fuse replacement of power cord (E) (replaceable 3 amp, 125 volt fuse is located in spare parts bag):
This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. Do not use with an extension cord unless plug
can be fully inserted. Do not alter or replace the plug.
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug
by pulling on cord.
2. Open fuse cover. Slide open the fuse access cover on top of attachment plug
toward blades.
3. Remove fuse carefully.
4. Risk of fire. Replace with only a 3 amp, 125 volt fuse (provided with product).
5. Close fuse cover. Slide close the fuse access cover on top of attachment plug.
B)
1.
2.
3.
Fuse replacement of power cord (E) (replaceable 3 amp, 125 volt fuses are located in spare parts bag):
Grasp plug and remove from its power source.
Locate blown fuse(s) by sliding access cover on top of plug towards prongs.
Remove blown fuse by turning the plug over. Fuse should fall into your hand
(gentle tapping may be required).
4. Locate spare replacement fuses in spare parts bag.
5. Replace blown fuse with spare replacement fuse(s). Close fuse cover by sliding
fuse access cover towards the cord.
CAUTION: To reduce risk of fire – replace fuse in the plug with only 3 amp, 125 volt fuse.
Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product
if the attachment plug is damaged.
BULB REPLACEMENT:
1.
2.
3.
4.
Grasp plug and remove from its power source.
Unlock the lock on the bulb socket.
Pull bulb AND plastic base straight out of socket. Do not twist bulbs while you are removing them.
Replace burned-out bulb with 3 V, 0.06 W LED bulb ONLY. (Additional bulbs are included for your
convenience.)
5. Relock the lamp lock on the bulb socket.
If the new bulb base does not fit in bulb holder, follow these steps before step 4:
 Pull reflector out.
 Remove the base of the burned-out bulb by straightening the bulb leads,
and gently pull bulb out.
 Thread leads of new bulb through holes in old base with one lead in each
hole.
 After bulb is fully inserted into base, bend each lead up so that the leads will touch the contacts inside the
bulb holder.
 Insert the reflector into the base.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:
(Inspect product carefully before using or re-using):
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b)
c)
d)
e)
f)
g)
h)
i)
j)
k)
l)
m)
n)
o)
p)
Do not use this product outdoors.
This seasonal use product is not intended for permanent installation or use.
Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat.
Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
Do not let lamps rest on the supply cord or on any wire.
For your safety, unplug the product when leaving the house, when retiring for the night, or if left
unattended.
This is an electric product - not a toy! To avoid risk of fire, burns, personal injury and electric shock it
should not be played with or placed where small children can reach it.
Do not use this product for other than its intended use.
Do not hang ornaments or other objects from cord, wire, or light string. Hang ornaments only on the tree
itself.
Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
Do not cover the product with cloth, paper or any material not part of the product when in use.
This product is equipped with push-in type lamps. Do not twist lamps.
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
This product contains an extension cord with a polarized plug (one prong is wider than the other) as a
feature to reduce the risk of electrical shock. This plug will fit in a polarized outlet only one way. If the
plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Do not use with an extension cord unless the plug can be fully inserted. Do not alter or replace the plug.
Read and follow all instructions that are on the product or provided with the product.
q)SAVE THESE INSTRUCTIONS.
Use and Care Instructions
a) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or
frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed
copper wire.
b) When storing the product, carefully remove the product from wherever you placed it, including trees,
branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and
wires.
c) When not in use, store neatly in a cool, dry location protected from sunlight.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
STORAGE: Disassembled tree can be stored in its original box. Store tree in a cool dry place where the
temperature does not exceed 100 degrees Fahrenheit.
SYLVANIA is a registered trademark of OSRAM SYLVANIA INC. used under license.
ONE PLUG® U.S. Patents: US8,454,186, US8,454,187, US8,936,379, US8,974,072, US9,157,588. Other
Patents Pending.
See www.williscorporation.com/about.html for a complete list of patents.