Washing Machine
User Manual
WTG841B2W
EN
Document Number=
2302061186
This product was manufactured using the latest technology in environmentally friendly conditions.
1 General safety instructions
This section includes security instructions which may help prevent
the injuries and material damage risks. All kinds of warranties shall
be invalid if these instructions are not observed.
1.1 Life and property safety
u
u
u
u
u
u
u
u
Never place the product on a carpet-covered floor. Electrical parts
will get overheated since air cannot circulate from under the device.
This will cause problems with your product.
Unplug the product if it is not in use.
Always have the installation and repairing procedures carried out
by the Authorized Service Agent. Manufacturer shall not be held
liable for damages that may arise from procedures carried out by
unauthorized persons.
The water supply and draining hoses must be securely fastened and
remain undamaged. Otherwise, water leak may occur.
While there is still water inside the product, never open the loading
door or remove the filter. Otherwise, risk of flooding and injury from
hot water will occur.
Do not force open the locked loading door. Door can be opened a few
minutes after the washing cycle ends. In case of forcing the loading
door to open, the door and the lock mechanism may get damaged.
Use detergents, softeners and supplements suitable for automatic
washing machines only.
Follow the instructions on the label of textiles and the detergent
package.
1.2 Children's safety
u
u
This product can be used by the children who are at the age of 8 and
over and the people whose physical, sensory or mental skills are not
fully developed or who do not have necessary required experience
and knowledge as long as they are supervised or trained about the
safe use of the product and its risks. Children should not play with the
device. Cleaning and maintenance works should not be performed
by children unless they are supervised by someone. Children of less
than 3 years should be kept away unless continuously supervised.
Packaging materials may be dangerous for the children. Keep
packaging materials in a safe place away from reach of the children.
Washing Machine / User’s Manual
3 / EN
u
u
u
Electrical products are dangerous for the children. Keep the children
away from the product when it is in use. Do not allow them to play
with the product. Use child lock to prevent children from intervening
with the product.
Do not forget to close the loading door when leaving the room where
the product is located.
store all detergents and additives in a safe place away from the
reach of the children by closing the cover of the detergent container
or sealing the detergent package.
1.3 Electrical safety
u
u
u
u
u
u
u
If the product has a failure, it should not be operated unless it is
repaired by the Authorized Service Agent. Risk of electric shock!
This product is designed to resume operating in the event of
powering on after a power interruption. If you wish to cancel the
programme, see "Cancelling the programme" section.
Plug the product into a grounded outlet protected by a 13 A fuse. Do
not neglect to have the grounding installation made by a qualified
electrician. Our company shall not be liable for any damages that
will arise when the product is used without grounding in accordance
with the local regulations.
Do not wash the product by spraying or pouring water onto it! Risk of
electric shock!
Never touch the power cable plug with wet hands! Do not grab the
power cord to unplug the machine, always unplug it by holding the
socket with one hand, and pulling the plug with the other hand.
Product should be unplugged during installation, maintenance,
cleaning and repair procedures.
If the power cable is damaged, it must be replaced by the
manufacturer, after sales service or a similarly qualified person
(preferably an electrician) or someone designated by the importer in
order to avoid possible risks.
1.4 Hot surface safety
4 / EN
While washing the laundry at high
temperatures, the loading door glass
will get hot. Considering this fact, during
washing operation keep the children away
from the loading door of the product to
prevent them touching it.
2 Important instructions for environment
2.1 Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This product bears a
classification symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which
can be reused and are suitable for recycling. Do not dispose of the waste product
with normal domestic and other wastes at the end of its service life. Take it to the
collection center for the recycling of electrical and electronic equipment. Please
consult your local authorities to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not
contain harmful and prohibited materials specified in the Directive.
2.2 Package information
Packaging materials of the product are manufactured from recyclable materials in accordance
with our National Environment Regulations. Do not dispose of the packaging materials together
with the domestic or other wastes. Take them to the packaging material collection points
designated by the local authorities.
3 Intended use
• This product has been designed for domestic use. It is not for commercial
purposes or it should not be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that are
marked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or
transportation.
• The service life of your product is 10 years. During this period, original spare
parts will be available to operate the appliance properly.
Washing Machine / User’s Manual
5 / EN
4
Complying Commission Delegated Regulation (EU) No 1061/2010
Supplier name or trademark
Beko
WTG841B2W
Model name
8
Rated capacity (kg)
Energy efficiency class / Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency)
Annual Energy Consumption (kWh)
(1)
A++
195
Energy consumption of the standard 60°C cotton programme at full load (kWh)
1.1
Energy consumption of the standard 60°C cotton programme at partial load (kWh)
0.70
Energy consumption of the standard 40°C cotton programme at partial load (kWh)
0.665
Power consumption in ‘off-mode’ (W)
0.250
Power consumption in ‘left-on mode’ (W)
1.000
Annual Water Consumption (l) (2)
10559
Spin-drying efficiency class / Scale from A (Highest Efficiency) to G (Lowest Efficiency)
1400
Maximum spin speed (rpm)
Remaining moisture Content (%)
Standard cotton programme
(3)
53
Cotton Eco 60°C and 40°C
Programme time of the standard 60°C cotton programme at full load (min)
200
Programme time of the standard 60°C cotton programme at partial load (min)
179
Programme time of the standard 40°C cotton programme at partial load (min)
179
Duration of the left-on mode (min)
Airborne acoustical noise emissions washing/spinning (dB)
N/A
61/74
Built-in
No
Height (cm)
84
Width (cm)
60
Depth (cm)
54
Net weight (±4 kg.)
70
Single Water inlet / Double Water inlet
Available
Electrical input (V/Hz)
230V~/50Hz
Total current (A)
10
Total power (W)
2200
Main model code
9211
Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and the consumption
of the low-power modes. Actual energy consumption will depend on how the appliance is used.
(1)
Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load. Actual water
consumption will depend on how the appliance is used.
(2)
“Standard 60°C cotton programme” and the “standard 40°C cotton programme” are the standard washing programmes to which the information
in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient
programmes in terms of combined energy and water consumption.
(3)
Technical specifications may be changed without prior notice to improve the quality of the product.
6 / EN
4.1Installation
• Apply to the nearest authorized service agent for the installation of your product.
• Preparation of the location and electrical, tap water and waste water installations at the place of
installation is under customer's responsibility.
• Make sure that the water inlet and discharge hoses as well as the power cable are not folded,
pinched or crushed while pushing the product into its place after installation or cleaning
procedures.
• Make sure that the installation and electrical connections of the product are performed by
authorized service. Manufacturer shall not be held liable for damages that may arise from
procedures carried out by unauthorized persons.
• Prior to installation, visually check if the product has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
4.1.1 Appropriate installation location
• Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other
similar surfaces.
• When the washing machine and dryer are placed on top of each other, their total weight –when
loaded– amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient
load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product in the environments where the temperature falls below 0 ºC.
• Leave a minimum space of 1 cm between the machine and the furniture.
• On a graduated floor, do not place the product next to the edge or on a platform.
• Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use
them on the product.
4.1.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by pulling the
ribbon. Do not make this operation alone by yourself.
4.1.3 Removing the transportation locks
1
2
3
Loosen all bolts with an appropriate wrench until they turn freely.
Remove the transport safety bolts by turning them slightly.
Insert the plastic covers in the bag containing the user manual to the openings on the rear
panel.
A
C
CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the
product will be damaged.
Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again
in the future.
Install the transport safety bolts in reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!
Washing Machine / User’s Manual
7 / EN
4.1.4 Connecting water supply
C
A
The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have
10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a
pressure reducing valve if water pressure is higher.
CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the
laundry will get damaged or the product will switch to protection mode and will not operate.
CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.
1
2
Tighten the nuts of the hose by hand. Never use a tool when
tightening the nuts.
When hose connection is completed, check whether there is
leak problems at the connection points by opening the taps
fully. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. In order to
prevent the water leaks and resultant damages, keep the taps
closed when you do not use the product.
4.1.5 Connecting the drain hose to the drain
• Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.
A
CAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge.
Moreover, there is risk of scalding due to high washing temperatures! In order to prevent such situations and
make sure that the machine performs water intake and discharge processes without any problem, fix the drain
hose securely.
• Connect the drain hose to a minimum height of 40
cm and a maximum height of 100 cm.
• In case the drain hose is elevated after laying it on
the floor level or close to the ground (less than 40 cm
above the ground), water discharge becomes more
difficult and the laundry may come out excessively
wet. Therefore, follow the heights described in the
figure.
• To prevent the waste water to go back into the machine again and to ensure easy drainage, do not
immerse the end of the hose into the waste water or do not insert it into the drain for more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be stepped on and the hose must not be
pinched between the drain and the machine.
• If the length of the hose is too short, use it by adding an original extension hose. Length of the
hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the
extension hose and the drain hose of the product must be fitted well with an appropriate clamp as
not to come off and leak.
8 / EN
4.1.6 Adjusting the feet
A
1
2
3.
CAUTION: In order to ensure that the product operates more silently and vibration-free, it must stand level
and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its
place and cause crushing and vibration problems.
CAUTION: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
Loosen the lock nuts on the feet by hand.
Adjust the feet until the product stands in a stable and balanced way.
Tighten all lock nuts by hand again.
4.1.7 Electrical connection
Connect the product to a grounded outlet protected by a 13 A fuse. Our company shall not be liable
for any damages that will arise when the product is used without grounding in accordance with
the local regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after installation.
• If the current value of the fuse or breaker in the house is less than 13 Amps, have a qualified
electrician install a 13 Amp fuse.
• The voltage specified in the "Technical specifications" section must be equal to your mains
voltage.
• Do not make connections via extension cables or multi-plugs.
B
CAUTION: Damaged power cables must be replaced by the Authorized Service Agents.
Electrical requirements
Before you insert the plug into the wall socket make sure that the voltage and the
frequency shown in the rating label corresponds to your electricity supply.
We recommend that this appliance be connected to the mains supply via a suitable switched
and fused socket in a readily accessible position.
Should the mains lead of the appliance become damaged or need replacing at any time, it
must be replaced by a special purpose made mains lead which can only be obtained from a
Authorised Service Agent.
BWARNING:
This appliance must be earthed.
Washing Machine / User’s Manual
9 / EN
If the fitted moulded plug is not suitable for your socket, then the plug should be cut off
and an appropriate plug fitted.
Destroy the old plug, which is cut off as a plug with a bared cord could cause a shock
hazard if inserted into a socket elsewhere in the house. The moulded plug on this
appliance incorporates a 13A fuse. Should the fuse need to be replaced an ASTA approved
BS1362 fuse of the same rating must be used. Do not forget to refit the fuse cover. In the
event of losing the fuse cover, the plug must not be used until a replacement fuse cover
has been fitted. Colour of the replacement fuse cover must be the same colour as that
visible on the pin face of the plug. Fuse covers are available from any good electrical store.
Important
Fitting a different plug
As the colours of the wires in the mains lead of this appliance may not correspond with
the coloured markings identifying the terminals on your plug, proceed as follows:
1 Connect the green - yellow or green (earth) wire to the terminal in the plug marked ‘E’
or with the symbol f or coloured green and yellow or green.
2 Connect the blue (neutral) wire to the terminal in the plug marked ‘N’ or coloured black.
3 Connect the brown (live) wire to the terminal in the plug marked ‘L’ or coloured red.
With the alternative plugs a 13A fuse must be fitted either in the plug or adaptor or in the
main fuse box. If in doubt contact a qualified electrician.
10 / EN
Washing Machine / User’s Manual
4.1.8 Initial use
C
Before starting to use the product make sure that the preparations
are made which are in line with the “Important Safety and
Environment Instructions” and the instructions in the “Installation”
section.
To prepare the product for washing laundry, perform first
operation in Drum Cleaning programme. If this programme is not
available in your machine, apply the method which is described in
the section 4.4.2.
Use an anti-limescale suitable for the washing machines.
Some water might have remained in the product due to the quality control processes in the production. It is not
harmful for the product.
Washing Machine / User’s Manual
11 / EN
4.2 Preparation
4.2.1 Sorting the laundry
* Sort laundry according to type of fabric, color, and degree of soiling and allowable water
temperature.
* Always obey the instructions given on the garment tags.
4.2.2 Preparing laundry for washing
• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons
will damage the machine. Remove the metal pieces or wash the clothes by putting them in a
laundry bag or pillow case.
• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside
out and brush. Such objects may damage the product or cause noise problem.
• Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.
• Place curtains in without compressing them. Remove curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips and tears.
• Wash “machine washable” or “hand washable” labeled products only with an appropriate
programme.
• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash
them separately.
• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
• Only use the dyes / color changers and descaling agents which are appropriate to machine wash.
Always follow the instructions on the package.
• Wash trousers and delicate laundry turned inside out.
• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will
reduce pilling.
• Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must
be shaken off before placing into the machine. Such dusts and powders on the laundry may build
up on the inner parts of the machine in time and can cause damage.
4.2.3 Things to be done for energy saving
Following information will help you use the product in an ecological and energy-efficient manner.
• Operate the product in the highest capacity allowed by the programme you have selected, but do
not overload; see, "Programme and consumption table". See, “Programme and consumption table"
• Always follow the instructions on the detergent packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly soiled laundry.
• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during
washing process.
• Do not use more detergent than the recommended amount specified on its package.
4.2.4 Loading the laundry
1. Open the laundry cover.
2. Put the laundry items into the machine in a loose manner.
3. Push and close the loading cover until you hear the locking sound. Ensure that no items are caught
in the door. The loading door is locked while a programme is running. The door can only be opened
a while after the programme comes to an end.
4.2.5 Correct load capacity
The maximum load capacity depends on the type of laundry, the degree of soiling and the washing
programme desired.
Machine automatically adjusts the water amount according to the weight of the laundry put inside it.
A
12 / EN
WARNING: Follow the information in the “Programme and consumption table”. When overloaded, machine's
washing performance will drop. Moreover, noise and vibration problems may occur.
Washing Machine / User’s Manual
4.2.6 Using detergent and softener
C
When using detergent, softener, starch, fabric dye, bleacher and decolorant, descaling agents; read the
manufacturer's instructions written on the package and follow the dosages specified. Use measuring cup if
available.
2
3 1
The detergent drawer is composed of three
compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– ( ) in addition, there is a siphon piece in the
softener compartment.
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the washing programme.
• While the washing cycle is in progress, do not leave the detergent dispenser open!
• When using a programme without prewash, do not put any detergent into the prewash
compartment (compartment nr. "1").
• In a programme with prewash, do not put liquid detergent into the prewash compartment
(compartment nr. "1").
• Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place
the detergent bag or the dispensing ball directly among the laundry in the machine.
If you are using liquid detergent, do not forget to place the liquid detergent container into the main
wash compartment (compartment number “2”).
Choosing the detergent type
Detergent type to be used depends on the fabric type and color.
• Use different detergents for coloured and white laundry.
• Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.)
used solely for delicate clothes.
• When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.
• Wash woolens with special detergent made specifically for woolens.
A
CAUTION: Use only detergents manufactured specifically for washing machines.
CAUTION: Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used depends on the amount of laundry, the degree of
soiling and water hardness.
• Do not use amounts exceeding the dosage quantities recommended on the detergent package
to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental
protection.
• Use lesser detergent for small amounts or lightly soiled clothes.
Using softeners
Pour the softener into the softener compartment of the detergent drawer.
• Do not exceed the (>max<) level sign on the softener compartment.
• If the softener has lost its fluidity, dilute it with water before putting it in the detergent drawer.
Washing Machine / User’s Manual
13 / EN
Using liquid detergents
If the product contains a liquid detergent cup:
22
•
•
Put the liquid detergent container into the
compartment no “2”.
If the liquid detergent lost its fluidity, dilute
it with water before putting it into the
detergent container.
If the product does not contain a liquid detergent cup:
• Do not use liquid detergent for the prewash in a programme with prewash.
• Liquid detergent stains your clothes when used with Delayed Start function. If you are going to
use the Delayed Start function, do not use liquid detergent.
Using gel and tablet detergent
• If the gel detergent thickness is fluidal and your machine does not contain a special liquid
detergent cup, put the gel detergent into the main wash detergent compartment during first
water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before
starting the programme.
• If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly
into the drum before washing.
• Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the
drum before washing.
Using starch
• Put the liquid soda, powder soda or the fabric dye into the softener compartment.
Do not use softener and starch together in a washing cycle.
Wipe the inside of the machine with a damp and clean cloth after using starch.
Using limescale remover
• When required, use limescale removers manufactured specifically for washing machines only.
Using bleaches
Add the bleach at the beginning of the washing cycle by selecting a prewash programme. Do not
put detergent in the prewash compartment. As an alternative application, select a programme
with extra rinse and add the bleaching agent while the machine is taking water from the
detergent compartment during first rinsing step.
• Donotusebleachingagentanddetergentbymixingthem.
• Usejustalittleamount(approx.50ml)ofbleachingagentandrinsetheclothesverywellasit
causes skin irritation. Do not pour the bleach onto the laundry and do not use it with the colored
items.
• Whenusingoxygen-baseddecolorant,selectaprogrammewhichwashesthelaundryatalow
temperature.
• Oxygen-baseddecolorantcanbeusedwiththedetergent;however,ifitisnotatthesame
consistence, first put detergent in the compartment number “2” in the detergent dispenser and
wait for the machine to flush the detergent when taking in water. While the machine continues
taking in water, add decolorant in the same compartment.
14 / EN
Washing Machine / User’s Manual
4.2.7 Tips for efficient washing
Clothes
Light Colours and
Whites
Soiling Level
(Recommended temperature
range based on soiling level:
o
40-90 C)
It may be necessary to pretreat the stains or perform
Heavily
prewash. Powder and liquid
detergents recommended
Soiled
for whites can be used at
(difficult stains dosages recommended for
such as grass, heavily soiled clothes. It is
recommended to use powder
coffee, fruits
detergents to clean clay and
and blood.)
soil stains and the stains that
are sensitive to bleaches.
Normally
Soiled
(For example,
stains caused
by body on
collars and
cuffs)
Lightly
Soiled
(No visible
stains exist.)
Powder and liquid detergents
recommended for whites
can be used at dosages
recommended for normally
soiled clothes.
Black/Dark
Colours
Delicates/
Woolens/
Silks
(Recommended temperature
range based on soiling level:
o
cold -40 C)
(Recommended
temperature range
based on soiling level:
o
cold -40 C)
(Recommended
temperature range
based on soiling
o
level: cold -30 C)
Powder and liquid detergents
recommended for colors can be
used at dosages recommended
for heavily soiled clothes. It is
recommended to use powder
detergents to clean clay and
soil stains and the stains that
are sensitive to bleaches. Use
detergents without bleach.
Liquid detergents
suitable for colors
and dark colors can
be used at dosages
recommended for
heavily soiled clothes.
Prefer liquid
detergents
produced for
delicate clothes.
woollen and silk
clothes must
be washed with
special woollen
detergents.
Powder and liquid detergents
recommended for colors can be
used at dosages recommended
for normally soiled clothes.
Detergents which do not
contain bleach should be used.
Liquid detergents
suitable for colors
and dark colors can
be used at dosages
recommended for
normally soiled
clothes.
Prefer liquid
detergents
produced for
delicate clothes.
woollen and silk
clothes must
be washed with
special woollen
detergents.
Liquid detergents
suitable for colors
and dark colors can
be used at dosages
recommended for
lightly soiled clothes.
Prefer liquid
detergents
produced for
delicate clothes.
woollen and silk
clothes must
be washed with
special woollen
detergents.
Colours
Powder and liquid detergents
Powder and liquid detergents
recommended for colors can be
recommended for whites
used at dosages recommended
can be used at dosages
for lightly soiled clothes.
recommended for lightly soiled
Detergents which do not
clothes.
contain bleach should be used.
Washing Machine / User’s Manual
15 / EN
4.3 Operating the product
4.3.1 Control panel
1
2
90°
60°
3
4
1000
800
40°
600
30°
400
20°
10
1 - Programme Selection knob (Uppermost
2 - Display
3 - Delayed Start button
4 - Programme Follow-up indicator
5 - Start / Pause button
9
8
7
6
5
6 - Auxiliary function button 3
7 - Auxiliary function button 2
8 - Auxiliary function button 1
9 - Spin Speed Adjustment button
10 - Temperature Adjustment button
1.Make sure that the hoses are connected tightly.
2.Plug in your machine.
3.Turn the tap on completely.
4.Place the laundry in the machine.
5.Add detergent and fabric softener.
1.Select the programme suitable for the type, quantity and soiling degree of the laundry in
accordance with the "Programme and consumption table" and the temperature table below.
2.Select the desired programme with the Programme Selection knob.
6 / EN
4.3.4 Programme and consumption table
Water Consumption (l)
Energy Consumption (kWh)
Max. Speed***
Prewash
Rinse Plus
Rinse Hold
re range °C
Fast+
Auxiliary functions
Max. Load (kg)
EN
90
8
93.0
2.3
1600
•
•
•
•
Cold - 90
60
8
93.0
1.7
1600
•
•
•
•
Cold - 90
40
8
90.0
1.1
1600
•
•
•
•
Cold - 90
60**
8
54.0
1.100
1600
Cold - 60
60**
4
43.5
0.700
1600
Cold - 60
40**
4
43.5
0.665
1600
60
3
70.0
1.2
1200
•
•
•
•
Cold - 60
40
3
68.0
0.8
1200
•
•
•
•
Cold - 60
90
8
67.0
2.2
1400
•
•
•
Cold - 90
60
8
67.0
1.2
1400
•
•
•
Cold - 90
30
8
65.0
0.2
1400
•
•
•
Cold - 90
Daily Quick/Super short +Fast 90
2
41.0
0.2
1400
•
•
•
Cold - 30
3.5
72.2
0.8
800
•
Cold - 40
Program
Cottons
Cottons Eco
Synthetics
Daily Quick / Super Short
Mixed Fabrics
40
Selectable
temperatu
Cold - 60
•
•
Hand Wash
40
1.5
55.0
0.6
1200
•
•
Cold - 40
Delicates
40
3.5
51.0
0.7
1200
•
•
Cold - 40
Down Wear
60
2
70.0
1.3
1000
Sports
40
3.5
45.0
0.5
1200
•
•
Cold - 40
Dark Care
40
3
86.4
0.9
1200
•
*
•
Cold - 40
Lingerie
30
1
1.7
70.1
600
*
•
Cold - 30
Shirts
60
3
59.5
1.2
800
•
•
Cold - 60
Baby&Toddler Clothing
90
8
124
2.4
1600
Drum Clean
90
-
80
2.3
600
•
•
•
*
Cold - 60
20-90
90
17 / EN
Indicative values for Synthetics programmes (EN)
Programme
Duration
(min) *
> 1000 rpm
Energy
Consumption
(kWh)
≤ 1000 rpm
Water
Consumption
(l)
Remaining Moisture
Content (%) **
Load (kg)
Remaining Moisture
Content (%) **
Synthetics 60
2,5
55
1,10
100/130
45
40
Synthetics 40
2,5
55
0,80
100/130
45
40
* You can see the washing time of the programme you have selected on the display of the machine. It is normal that
small differences may occur between the time shown on the display and the real washing time.
** Remaining moisture content values may differ according to the selected spin speed.
4.3.5 Main programmes
Depending on the type of fabric, use the following main programmes.
• Cottons
You can wash your durable cotton laundry (sheets, bedlinen, towels, bathrobes, underwear etc.)
in this programme. When the quick wash function button is pressed, programme duration
becomes notably shorter but effective washing performance is ensured with intense washing
movements. If the quick wash function is not selected, superior washing and rinsing performance
is ensured for your heavily soiled laundry.
• Synthetics
You can wash your laundry (such as shirts, blouses, synthetic/cotton blended fabrics etc.) in this
programme. The programme duration gets notable shorter and washing with high performance is
ensured. If the quick wash function is not selected, superior washing and rinsing performance is
ensured for your heavily soiled laundry.
• Hand Wash
Use to wash your woolen/delicate laundry. Select the appropriate temperature complying with
the tag of your clothes. Your laundry will be washed with a very gentle washing action in order not
to damage the clothes.
4.3.6 Additional programmes
For special cases, additional programmes are available in the machine.
C
Additional programmes may differ according to the model of the machine.
• Cottons Eco
Use to wash your normally soiled, durable cotton and linen laundry. Although it washes longer than
all other programmes, it provides high energy and water savings. Actual water temperature may be
different from the stated wash temperature. When you load the machine with less laundry (e.g. ½
capacity or less), periods in programme stages may automatically get shorter. In this case, energy
and water consumption will decrease more, providing a more economic wash.
18 / EN
Washing Machine / User’s Manual
when the machine starts to take water from the main washing compartment. Thus, you can obtain
the same performance as you obtain with normal washing in a much shorter period of time. Usage
life of your shirts increases.
• Sports
You can use this programme to wash sports and outdoors garments that contain cotton/synthetics
mix and water repellent covers such as gore-tex etc. It makes sure your garments are washed
gently thanks to special rotating movements.
• Lingerie
You can use this programme to wash delicate garments that are suitable for hand wash and delicate
women's underwear. Small amount of garments must be washed in a washing net. Hooks, buttons
etc. must be done up and zips must be zipped up.
• Down Wear
Use this programme to wash your coats, vest, jackets etc. containing feathers with a "machinewashable" label on them. Thanks to special spinning profiles, it is ensured that the water reaches
the air gaps amongst the feathers.
Washing Machine / User’s Manual
19 / EN
4.3.7 Special programmes
For specific applications, select any of the following programmes.
• Rinse
Use when you want to rinse or starch separately.
• Spin+Drain
You can use this function to remove the water on the garment of drain the water in the machine.
Before selecting this programme, select the desired spin speed and press Start / Pause button. First,
the machine will drain the water inside of it. Then, it will spin the laundry with the set spin speed and
drain the water coming out of them.
If you wish to drain only the water without spinning your laundry, select the Pump+Spin programme
and then select the No Spin function with the help of Spin Speed Adjustment button. Press Start /
Pause button.
C
Use a lower spin speed for delicate laundries.
4.3.8 Temperature selection
Whenever a new programme is selected, the recommended temperature value for the selected
programme appears on the temperature indicator.
To decrease the temperature, press the Temperature Adjustment button. Temperature will decrease
gradually. Temperature level lights will not turn on when the cold level is selected.
C
If the programme has not reached the heating step, you can change the temperature without switching the
machine to Pause mode.
4.3.9 Spin speed selection
Whenever a new programme is selected, the recommended spin speed of the selected programme is
displayed on the spin speed indicator.
To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed decreases
gradually. Then, depending on the model of the product, "Rinse Hold" and "No Spin" options appear
on the display. When "No Spin" is selected, the rinse level indicator lights will not turn on.
Rinse hold
If you are not going to unload your clothes immediately after the programme completes, you can
use rinse hold function to keep your laundry in the final rinsing water in order to prevent them from
getting wrinkled when there is no water in the machine. Press Start / Pause button after this process
if you want to drain the water without spinning your laundry. Programme will resume and complete
after draining the water.
If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause button.
The programme will resume. Water is drained, laundry is spun and the programme is completed.
C
If the programme has not reached the spinning step, you can change the speed without switching the machine
to Pause mode.
4.3.10 Auxiliary function selection
Select the desired auxiliary functions before starting the programme. Furthermore, you may also
select or cancel auxiliary functions that are suitable to the running programme without pressing the
Start / Pause button when the machine is operating. For this, the machine must be in a step before
the auxiliary function you are going to select or cancel.
If the auxiliary function cannot be selected or canceled, light of the relevant auxiliary function will
blink 3 times to warn the user.
C
If a second auxiliary function conflicting with the first one is selected before starting the machine, the function
selected first will be canceled and the second auxiliary function selection will remain active.
An auxiliary function that is not compatible with the programme cannot be selected. (See, "Programme and
consumption table")
Auxiliary Function buttons may vary according to the model of the machine.
20 / EN
Washing Machine / User’s Manual
4.3.10.1 Auxiliary functions
• Prewash
A Prewash is only worthwhile for heavily soiled laundry. Not using the Prewash will save energy,
water, detergent and time.
C
Prewash without detergent is recommended for tulle and curtains.
C
When you select this function, load your machine with half of the maximum laundry specified in the programme
table.
• Fast+
When this function is selected, the durations of the relevant programmes get shorter by 50%.
Thanks to the optimised washing steps, high mechanic activity and optimum water consumption,
high washing performance is achieved in spite of the reduced duration.
• Extra Rinse
This function enables the product to make another rinsing in addition to the one already made
after the main wash. Thus, the risk for sensitive skins (babies, allergic skins, etc.) to be effected by
the minimal detergent remnants on the laundry can be reduced.
4.3.10.2 Functions/Programmes Selected by Pressing the Function Buttons for 3 Seconds
• Drum Clean 3II
Press and hold the auxiliary function button 1 for 3 seconds to select the programme.
Use regularly (once in every 1-2 months) to clean the drum and provide the required hygiene.
Operate the programme while the machine is completely empty. To obtain better results, put
powder lime-scale remover for washing machines into the detergent compartment no. “2”. When the
programme is over, leave the loading door ajar so that the inside of the machine gets dry.
C
This is not a washing programme. It is a maintenance programme.
Do not run the programme when there is something in the machine. If you try to do so, the machine detects that
there is load inside and aborts the programme.
• Child lockI
Use Child Lock function to prevent children from tampering with the machine. Thus you can avoid
any changes in a running programme.
C
If the Programme Selection knob is turned when the Child Lock is active, "Con" appears on the display. The Child
Lock does not allow any change in the programmes and the selected temperature, speed and auxiliary functions.
Even if another programme is selected with the Programme Selection knob while the Child Lock is active,
previously selected programme will continue running.
To activate the Child Lock:
2. Pres and hold the Auxiliary Function button for 3 seconds. C03, C02, C01 will appear on the display
respectively while you keep the button pressed for 3 seconds. Then, while the light of the Auxiliary
Function button 2 is flashing, "Con" will appear on the display indicating that the child lock has been
activated. If you press any button or turn the Programme Selection knob when the Child Lock is
active, same phrase will appear on the display.
Washing Machine / User’s Manual
21 / EN
To deactivate the Child Lock:
Press and hold the Auxiliary Function button 2 for 3 seconds while a programme is running. C03,
C02, C01 will appear on the display respectively while you keep the button pressed for 3 seconds.
Then, while the light of the auxiliary function button 2 is flashing, "COF" will appear on the display
indicating that the child lock has been deactivated.
C
In addition to the method above, to deactivate the Child Lock, switch the Programme Selection knob to On / Off
position when no programme is running, and select another programme.
Child Lock is not deactivated after power failures or when the machine is unplugged.
4.3.11 Delayed Start
With the Delayed Start function the startup of the programme may be delayed up to 19 hours.
Delayed start time can be increased by increments of 1 hour.
C
Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the clothes.
C
Additional laundry may be loaded during the delayed start period.
1. Open the loading door, place the laundry and put detergent, etc.
2. Select the washing programme, temperature, spin speed and, if required, the auxiliary functions.
3. Set the desired time by pressing the Delayed Start button.
4. Press Start / Pause button. The delayed start time you have set is displayed. Delayed start
countdown starts. “_” symbol next to the delayed start time moves up and down on the display.
5. At the end of the countdown, duration of the selected programme will be displayed. “_” will
disappear and the selected programme will start.
Changing the delayed start period
If you want to change the time during countdown:
1. Press the Delayed Start button. Time will increase by 1 hour each time you press the button.
2. If you want to decrease the delayed start time, press Delayed Start button repeatedly until the
desired delayed start time appears on the display.
Cancelling the Delayed Start function
If you want to cancel the delayed start countdown and start the programme immediately:
1. Set the Delayed Start period to zero or turn the Programme Selection knob to any programme.
Thus, Delayed Start function will be canceled. The End/Cancel light flashes continuously.
2. Then, select the programme you want to run again.
3. Press Start / Pause button to start the programme.
4.3.12 Starting the programme
1. Press Start / Pause button to start the programme.
2. Programme follow-up light showing the startup of the programme will turn on.
C
22/ EN
If no programme is started or no button is pressed within 1 minute during programme selection process, the
machine will switch to Pause mode and the illumination level of the temperature, speed and loading door
indicator lights will decrease. Other indicator lights and indicators will turn off. Once the Programme Selection
knob is rotated or any button is pressed, indicator lights and indicators will turn on again.
Washing Machine / User’s Manual
4.3.13 Progress of programme
Progress of a running programme can be followed from the Programme Follow-up indicator. At
the beginning of every programme step, the relevant indicator light will turn on and light of the
completed step will turn off.
You can change the auxiliary functions, speed and temperature settings without stopping the
programme flow while the programme is running. To do this, the change you are going to make must
be in a step after the running programme step. If the change is not compatible, relevant lights will
flash for 3 times.
C
If the machine does not pass to the spinning step, Rinse Hold function might be active or the automatic
unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the
machine.
4.3.14 Loading door lock
There is a locking system on the loading door of the machine that prevents opening of the loading
door in cases when the water level is unsuitable.
Loading door light will start flashing when the machine is switched to Pause mode. Machine checks
the level of the water inside. If the level is suitable, Loading Door light illuminates steadily within 1-2
minutes and the loading door can be opened.
If the level is unsuitable, Loading Door light turns off and the loading door cannot be opened. If you
are obliged to open the Loading Door while the Loading Door light is off, you must cancel the current
programme. See. "Cancelling the programme"
4.3.15 Changing the selections after programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine to pause mode while a programme is running.
The light of the step which the machine is in starts flashing in the Programme Follow-up indicator to
show that the machine has been switched to the pause mode.
Also, when the loading door is ready to be opened, Loading Door light will also illuminate
continuously in addition to the programme step light.
Changing the auxiliary function, speed and temperature
Depending on the step the programme has reached, you can cancel or select the auxiliary functions.
See, "Auxiliary function selection".
You can also change the speed and temperature settings. See, "Spin speed selection" and
"Temperature selection".
C
If no change is allowed, the relevant light will flash 3 times.
Adding or taking out laundry
1. Press Start / Pause button to switch the machine to pause mode. The programme follow-up light
of the relevant step during which the machine was switched into the pause mode will flash.
2.Wait until the Loading Door can be opened.
3. Open the Loading Door and add or take out the laundry.
4.Close the Loading Door.
5. Make changes in auxiliary functions, temperature and speed settings if necessary.
6. Press Start / Pause button to start the machine.
Washing Machine / User’s Manual
23 / EN
4.3.16 Cancelling the programme
To cancel the programme, turn the Programme Selection knob to select another programme.
Previous programme will be cancelled. End / Cancel light will flash continuously to notify that the
programme has been canceled.
Your machine will end the programme when you turn the Programme Selection knob; however, it
does not drain the water inside. When you select and start a new programme, the newly selected
programme will start depending on the step the previous programme was canceled in. For example,
it may take in additional water or continue to wash with the water inside.
C
Depending on the step where the programme was canceled in, you may have to put detergent and softener
again for the programme you have selected anew.
4.3.17 End of programme
“End” appears on the display at the end of the programme.
1. Wait until the loading door light illuminates steadily.
2. Press On / Off button to switch off the machine.
3. Take out your laundry and close the loading door. Your machine is ready for the next washing
cycle.
4.3.18 Your machine features "Standby Mode".
After you switch on your machine with On-Off button, if no programme is started or no other
procedure is performed at the selection step or no action is taken within approx. 2 minutes after
the selected programme ends, your machine will switch to energy saving mode automatically.
The brightness of the indicator lights will decrease. Also, if your product has a display that shows
programme time, this display will be completely turned off. If you turn the Programme Selection knob
or touch any button, lights and display will switch back to previous condition. The selections which
you make when exiting from the energy efficiency may change. Please check the correctness of your
selections before starting the programme. If necessary, please make your settings again. This is not
an error.
24 / EN
Washing Machine / User’s Manual
4.4 Maintenance and cleaning
Service life of product extends and frequently experienced problems will be reduced if it is cleaned at
regular intervals.
4.4.1 Cleaning the detergent drawer
1
2.
3
Clean the detergent drawer at regular intervals (every 4-5 washing cycles)
as shown below in order to prevent accumulation of powder detergent in
time.
Lift the rear part of the siphon to remove it as illustrated.
If more than normal amount of water and softener mixture starts to gather
in the softener compartment, the siphon must be cleaned.
Press the dotted point on the siphon in the softener compartment and pull towards you until
the compartment is removed from the machine.
Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin.
In order to prevent the residues to contact your skin, clean it with an appropriate brush by
wearing a pair of gloves.
Insert the drawer back into its place after cleaning and make sure that it is seated well.
4.4.2 Cleaning the loading door and the drum
For products with drum cleaning programme, please see Operating the product - Programmes.
C
Repeat Drum Cleaning process in every 2 months.
Use an detergent / anti-limescale suitable for the washing machines.
After every washing make sure that no foreign substance is left in the drum.
If the holes on the bellow shown in the figure is blocked, open the holes using
a toothpick.
Foreign metal substances will cause rust stains in the drum. Clean the stains
on the drum surface by using cleaning agents for stainless steel.
Never use steel wool or wire wool. These will damage the painted, chromated
and plastic surfaces.
4.4.3 Cleaning the body and control panel
Wipe the body of the machine with soapy water or non-corrosive mild gel detergents as necessary,
and dry with a soft cloth.
Use only a soft and damp cloth to clean the control panel.
4.4.4 Cleaning the water intake filters
There is a filter at the end of each water intake valve at the rear of the machine and also at the
end of each water intake hose where they are connected to the tap. These filters prevent foreign
substances and dirt in the water to enter the washing machine. Filters should be cleaned as they do
get dirty.
1. Close the taps.
2. Remove the nuts of the water intake hoses to access
the filters on the water intake valves. Clean them
with an appropriate brush. If the filters are too dirty,
remove them from their places with a pliers and clean
in this way.
3. Take out the filters on the flat ends of the water
intake hoses together with the gaskets and clean
thoroughly under running water.
4. Replace the seals and filters carefully and tighten
their nuts by hand.
Washing Machine / User’s Manual
25 / EN
4.4.5 Draining remaining water and cleaning the pump filter
The filter system in your machine prevents solid items such as buttons, coins and fabric fibres
clogging the pump impeller during discharge of washing water. Thus, the water will be discharged
without any problem and the service life of the pump will extend.
If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is
clogged or in every 3 months. Water must be drained off first to clean the pump filter.
In addition, prior to transporting the machine (e.g., when moving to another house) and in case of
freezing of the water, water may have to be drained completely.
A
CAUTION: Foreign substances left in the pump filter may damage your machine or may cause noise problem.
CAUTION: If the product is not being used, shut the tap shut, remove mains pipe and drain the water inside
the machine against any likely freezing.
CAUTION: After each use, turn off the water tap to which the mains hose is connected.
In order to clean the dirty filter and discharge the water:
1 Unplug the machine to cut off the supply power.
A
CAUTION: Temperature of the water inside the machine may rise up to 90 ºC. To avoid the burning risk, clean
the filter after the water inside the machine is cooled down.
2. Open the filter cover.
3 Follow the below procedures in order to drain water.
The product does not have an emergency water drain hose, in order to drain the water:
a.
b.
c
In order to collect the water to flow out of the
filter, place a large vessel in front of the filter.
Turn and loosen the pump filter until water
starts to flow (counterclockwise). Fill the
flowing water into the container you have
placed in front of the filter. Always keep a piece
of cloth handy to absorb any spilled water.
When the water inside the machine is finished,
take out the filter completely by turning it.
4. Clean any residues inside the filter as well as fibres, if any, around the pump impeller region.
5. Replace the filter.
6. If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one
piece, seat the tabs in the lower part into their places first, and then press the upper part to
close.
26 / EN
Washing Machine / User’s Manual
Troubleshooting
5
Problem
Programme does not start
after c
Programme cannot be started or
selected.
Reason
Start / Pause / Cancel button was not pressed.
pressure, etc.).
mode after the programme
water.
the programme started.
low voltage.
come to an end.
27 / EN
Problem
Washing takes longer time than
specified in the manual.(*)
Reason
Water pressure is low.
Voltage might be low.
Input temperature of water might be low.
Number of rinses and/or amount of rinse water
might have increased.
Programme time does not
countdown. (On models with
display) (*)
Programme time does not
countdown. (*)
Machine does not switch to
spinning step. (*)
Washing performance is poor:
Laundry turns gray. (**)
Washing performance is poor:
Stains persist or the laundry is
not whitened. (**)
28 / EN
Solution
• Machine waits until taking in adequate
amount of water to prevent poor washing
quality due to the decreased amount of
water. Therefore, the washing time extends.
• Washing time is prolonged to avoid poor
washing results when the supply voltage
is low.
• Required time to heat up the water extends
in cold seasons. Also, washing time can be
lengthened to avoid poor washing results.
• Machine increases the amount of rinse water
when good rinsing is needed and adds an
extra rinsing step if necessary.
• Use recommended amount of detergent.
Excessive foam might have occurred and
automatic foam absorption system might have
been activated due to too much detergent usage.
Timer may stop during water intake.
• Timer indicator will not countdown until the
machine takes in adequate amount of water.
The machine will wait until there is sufficient
amount of water to avoid poor washing
results due to lack of water. Timer indicator
will resume countdown after this.
Timer may stop during heating step.
• Timer indicator will not countdown until the
machine reaches the selected temperature.
Timer may stop during spinning step.
• Automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the drum.
There might be unbalanced load in the machine. • Automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the drum.
There might be unbalanced load in the machine. • Automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the drum.
The machine will not spin if water is not drained
• Check the filter and the draining hose.
completely.
Excessive foam might have occurred and
• Use recommended amount of detergent.
automatic foam absorption system might have
been activated due to too much detergent usage.
Insufficient amount of detergent has been used • Use the recommended amount of detergent
over a long period of time.
appropriate for water hardness and the
laundry.
Washing was made at low temperatures for a
• Select the proper temperature for the
long time.
laundry to be washed.
Insufficient amount of detergent is used with
• Using insufficient amount of detergent with
hard water.
hard water causes the soil to stick on the
cloth and this turns the cloth into gray in
time. It is difficult to eliminate graying once
it happens. Use the recommended amount
of detergent appropriate for water hardness
and the laundry.
Too much detergent is used.
• Use the recommended amount of detergent
appropriate for water hardness and the
laundry.
Insufficient amount of detergent is used.
• Use the recommended amount of detergent
appropriate for water hardness and the
laundry.
Excessive laundry was loaded in.
• Do not load the machine in excess. Load with
amounts recommended in the "Programme
and consumption table".
Wrong programme and temperature were
• Select the proper programme and
selected.
temperature for the laundry to be washed.
Wrong type of detergent is used.
• Use original detergent appropriate for the
machine.
Too much detergent is used.
• Put the detergent in the correct
compartment. Do not mix the bleaching
agent and the detergent with each other.
Washing Machine / User’s Manual
Problem
Washing performance is poor:
Oily stains appeared on the
laundry. (**)
Reason
Regular drum cleaning is not applied.
Solution
• Clean the drum regularly. For this, please
see 4.4.2.
• Leave the detergent drawer as well as
the loading door of the machine ajar after
each washing. Thus, a humid environment
favorable for bacteria cannot occur in the
machine.
Colour of the clothes faded. (**) Excessive laundry was loaded in.
• Do not load the machine in excess.
Detergent in use is damp.
• Keep detergents closed in an environment
free of humidity and do not expose them to
excessive temperatures.
A higher temperature is selected.
• Select the proper programme and
temperature according to the type and
soiling degree of the laundry.
It does not rinse well.
The amount, brand and storage conditions of the • Use a detergent appropriate for the washing
detergent used are inappropriate.
machine and your laundry. Keep detergents
closed in an environment free of humidity
and do not expose them to excessive
temperatures.
Detergent is put in the wrong compartment.
• If detergent is put in the prewash
compartment although prewash cycle is not
selected, machine can take this detergent
during rinsing or softener step. Put the
detergent in the correct compartment.
Pump filter is clogged.
• Check the filter.
Drain hose is folded.
• Check the drain hose.
Laundry became stiff after
Insufficient amount of detergent is used.
• Using insufficient amount of detergent for
washing. (**)
the water hardness can cause the laundry
to become stiff in time. Use appropriate
amount of detergent according to the water
hardness.
Detergent is put in the wrong compartment.
• If detergent is put in the prewash
compartment although prewash cycle is not
selected, machine can take this detergent
during rinsing or softener step. Put the
detergent in the correct compartment.
Detergent might be mixed with the softener.
• Do not mix the softener with detergent.
Wash and clean the dispenser with hot water.
Laundry does not smell like the Detergent is put in the wrong compartment.
• If detergent is put in the prewash
softener. (**)
compartment although prewash cycle is not
selected, machine can take this detergent
during rinsing or softener step. Wash and
clean the dispenser with hot water. Put the
detergent in the correct compartment.
Detergent might be mixed with the softener.
• Do not mix the softener with detergent.
Wash and clean the dispenser with hot water.
Detergent residue in the
Detergent is put in wet drawer.
• Dry the detergent drawer before putting in
detergent drawer. (**)
detergent.
Detergent has gotten damp.
• Keep detergents closed in an environment
free of humidity and do not expose them to
excessive temperatures.
Water pressure is low.
• Check the water pressure.
The detergent in the main wash compartment got • Check the holes and clean if they are clogged.
wet while taking in the prewash water. Holes of
the detergent compartment are blocked.
There is a problem with the detergent drawer
• Call the Authorized Service Agent.
valves.
Detergent might be mixed with the softener.
• Do not mix the softener with detergent.
Wash and clean the dispenser with hot water.
Regular drum cleaning is not applied.
• Clean the drum regularly. For this, please
see 4.4.2.
Washing performance is poor:
Clothes smell unpleasantly. (**)
Odours and bacteria layers are formed on the
drum as a result of continuous washing at lower
temperatures and/or in short programmes.
Washing Machine / User’s Manual
29 / EN
Problem
Reason
Solution
Improper detergents for the washing machine are • Use detergents appropriate for the washing
being used.
machine.
Excessive amount of detergent is used.
• Use only sufficient amount of detergent.
Detergent was stored under improper conditions. • Store detergent in a closed and dry location.
Do not store in excessively hot places.
Some meshed laundry such as tulle may foam too • Use smaller amounts of detergent for this
much because of their texture.
type of item.
Detergent is put in the wrong compartment.
• Put the detergent in the correct
compartment.
Softener is being taken early.
• There may be problem in the valves or in the
detergent dispenser. Call the Authorized
Service Agent.
Foam is overflowing from the
Too much detergent is used.
• Mix 1 tablespoonful softener and ½ l water
detergent drawer.
and pour into the main wash compartment of
the detergent drawer.
• Put detergent into the machine suitable
for the programmes and maximum
loads indicated in the “Programme and
consumption table”. When you use additional
chemicals (stain removers, bleachs and etc),
reduce the amount of detergent.
Laundry remains wet at the end Excessive foam might have occurred and
• Use recommended amount of detergent.
of the programme. (*)
automatic foam absorption system might have
been activated due to too much detergent usage.
Too much foam forms in the
machine. (**)
(*) Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the
machine and to its surrounding environment. Laundry should be rearranged and re-spun.
(**) Regular drum cleaning is not applied. Clean the drum regularly. See 4.4.2
A
CAUTION: If you cannot eliminate the problem although you follow the instructions in this section, consult your
dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.
30 / EN
Washing Machine / User’s Manual
6
Guarantee
Booklet provided.
against the cost of breakdown repairs
for twelve months from the date of the
original purchase.
What is covered?
materials, defective components or
manufacturing defect.
is recommended for all Washing
Machines, Dishwashers and Electric
Cookers
a Gas Safe (or BORD GAIS) registered
Gas Installer.
parts, but excluding consumable
items.
repairer to carry out the repair.
What is not covered?
or misuse and abuse.
including knobs, flaps, handles or
container lids.
including but not limited to, ice trays,
scrapers, cutlery baskets, filters and
light bulbs.
new products and is not transferable if
the product is resold.
incidental or consequential damages.
diminish your statutory or legal rights.
Should you experience any difficulty in
obtaining service please contact the Beko
Customer Help-Line.
e-mail:service@beko.co.uk
unauthorised repair or inexpert
installation that fails to meet the
requirements contained in the user
instruction book.
commercial or non-residential
household premises.
often included within your household
contents insurance policy, or may be
available separately from your retailer).
Important notes.
built for domestic household use only.
product is installed or used in
commercial or non-residential
domestic household premises.
installed, located and operated in
accordance with the instructions
contained in the User Instructions
Washing Machine / User’s Manual
31 / EN
7
Service
Please keep your purchase receipt or
other proof of purchase in a safe place;
you will need to have it should the product
require attention under guarantee.
below; it will help us assist you when
requesting service. (The model number
is printed on the Instruction Booklet and
Label affixed to the appliance)
Service once the manufacturers
guarantee has expired.
If you have purchased an extended
guarantee please refer to the instructions
contained within the extended guarantee
agreement document. Otherwise please
call the appropriate number above where
service can be obtained at a charge.
Should you experience any difficulty in
obtaining service please contact the Beko
Customer Help-Line.
Model No:
Serial No:
Date of purchase:
For service under guarantee simply
telephone the appropriate number below
Tel: 0845 600 4911 or
0345 600 4911
e-mail:service@beko.co.uk
UK Mainland & Northern Ireland
Fridges & Freezers
0845 600 4903 or
0345 600 4903
Electric Cookers
0845 600 4902 or
0345 600 4902
Gas &
Dual Fuel Cookers
0845 600 4905 or
0345 600 4905
Dishwashers
0345 600 4906
or
Republic of Ireland
Washing Machines & Dishwashers
Before requesting service please
check the trouble-shooting guide in the
Operating Instructions as a charge may be
levied where no fault is found even though
your product may still be under guarantee.
32 / EN
Washing Machine / User’s Manual
BEKO plc. Beko House, 1 Greenhill Crescent,
Watford Herts WD18 8QU