FAST MASH NEW - Crem International

User Guide
FAST MASH NEW
Your Dealer
...............................................................................
...............................................................................
U / EN
Rev. 120127
1. Contents
Fast Mash New
1.
2.
3.
3.
3.
3.
Contents
General
Component overview, front
Component overview, inside
Component overview, programming electronics
Component overview, function buttons
4.
SERVICE: Installation and Start-up
Position machine
Hook up water to machine
Start the mash machine
Fill ingredients in container
8
8
8
9
OPERATION
Portion preparation
10
CLEANING Every day
Rinsing the blender system:
Rinsing the blender system
Remove blender system
Wash parts
Re-install blender system
11
11
12
12
12
7.
Error message
13
8.
PROGRAMMING
Use code, adjust the recipe value
Reset the cup counter
Storage and transportation
Dimension sketch
Cleaning and care
14- 18
19
20
21
22
5.
6.
9.
10.
11.
12.
2.
page
2
3
4
5
6.
7
2. General
Fast Mash New
Thank you for choosing a Fast Mash mash machine. We hope you enjoy it!
-
The machine must be connected correctly for your own safety.
Read the user guide before using the machine.
The guide contains important instructions for proper and safe use of the machine.
Always keep the guide close at hand.
Fast Mash is the mash machine that makes it possible for you to quickly
and easily serve freshly made mash in portions.
-
2 selection of portion (see chart, recipe)
1 ingredients container
Electronic temperature control
Cleaning function
Rinsing function on outside
Facts;
Height
Width
Depth
536 mm
211 mm
446 mm
Power supply
230V/2200W
Cold water hook-up ½" external thread for fitting factory-supplied tube
3.
3. Component view, front.
Fast Mash New
Selection buttons for mash
Tap for
mash
Holder for mash scoop
Drip tray
insert
Drip tray
Service plug
Emptying of water tank
Connection of
power cord
Water hook-up
4.
3. Component view, inside
Fast Mash New
Cleaning button
Concentrate
container for
mash
Concentrator
Condensation trap
Blender cups
ON/OFF
switch
4 Amp fuse
5.
3. Component overview, electronics
Fast Mash New
Programming
electronics
The programming electronics is placed behind the concentrate container.
6.
3. Component overview, function.
Fast Mash New
1
2
3
5
4
Function buttons
1.
2.
3.
Large mash.
Small mash.
Rinsing. (Use the rinse function regularly)
4.
Clean blender system.
5.
Ready lamp
The lamp stops blinking when the machine is ready.
The lamp blinks when a drink is being dispensed.
7.
4. Service. Installation and start-up
1.
Place the machine on a flat
waterproof surface.
Fast Mash New
Connect the plug to an
earthed 230V 10A wall outlet.
Note: Make sure air is able to circulate freely
behind the machine.
2.
Connect the factory-supplied tube to the cold water feed using a ½” R- connection
piece. Make sure no folding or sharp bending occurs when you push the machine
back in place.
If the water pipeline is new, flush the system with water first to remove
copper shavings. These can damage the inlet valve.
3.
4.
Open the water tap.
Hit the ON/OFF switch inside the panel.
The water tank will fill automatically with
1.8 litres of water.
The element will not be powered until the water
reaches the level indicator.
the temperature is set to 85º Celsius.
5.
Shut the panel door. The mash machine is ready
to be used within approx. 10 minutes.
8.
ON/OFF
switch
4. Service. Installation and start-up
6.
Fill ingredients in container
1.
Remove the concentrate container to avoid
spilling the concentrate in the machine) and fill
with ingredients.
Twist the concentrate tube up out of the
blender cup.
Lift the front edge of the concentrate
container and pull out.
2.
3.
Fast Mash New
Lift the lid and fill with concentrate.
(A).
7.
When placing the concentrate container
Make sure the concentrate tube is close to
the condensation traps (A), as illustrated.
9.
5. OPERATION; Portion preparation.
Fast Mash New
Portion preparation:
1.
2.
Place the mash scoop in the holder (A).
PRESS the button Large or Small Mash once.
The potato mash machine will make one portion of potato mash of the
size set.
3.
Wait until the light stops flashing before removing the mash scoop.
B
A
10.
6. CLEANING:
Cleaning every day.
Fast Mash New
Rinsing the blender system: Cleaning of valves and blender system.
The blender cup can be cleaned easily using the cleaning button.
We recommend you clean/rinse the entire blender system at least once a day.
1
1.
Loosen and remove the holder for the mash scoop.
2.
Centre a large cup on the drip tray.
3.
Open the door. Press the cleaning button (1)
4.
The machine starts by tapping valves
and then rinsing the mixer and blender cup.
Rinsing:
When the button marked "Rinsing" is depressed water at the temperature that
the thermostat is set to rinse through the blender cup and whisk housing.
Preferably place the scoop in the container to collect the water.
This function must be used before preparation starts if the machine has not been used
within the last hour.
We recommend running the rinse function at least every five portions.
Please make a habit of regularly use the rinsing function.
11.
6. CLEANING:
Cleaning every day.
Cleaning every day. Disassemble blender system.
1. Begin by loosening
the condensation trap and the
blender cup following image
steps 1, 2, 3
5.
2. Loosen the whisk housing
following image steps 4 and
5.
3. Loosen the wish, pull
straight out D.
4. Loosen the fitting plate, turn
clockwise following image C.
Wash disassembled parts and ensure that they are completely dry before
refitting them and before the mash machine is used again.
Blender cup - Condensation trap - Whisk - Whisk housing - Fitting plate
Reassemble the blender system.
6. Reassemble the blender system in the reverse order.
IMPORTANT! When refitting the wish, the plane side A of the whisk motor shaft must correspond
with marking B on the whisk.
Wash these parts and refit them.
Concentrate container
Concentrator
Holder for
mash scoop
mash scoop
Drip tray
Note: The container for the potato mash powder must be washed in warm water using detergent
once a week.
12.
7. Error message.
Error message
If the mash machine is maintained and cleaned as recommended, it will
work faultlessly.
If problems occur despite this:
•
No potato mash comes after pressing the button
"Large mash" or "Small mash"
- open the door and ensure that potato mash has not stuck in the blender cup
and caused a stop.
If so is the case, disassemble the whisk housing etc and clean.
•
The mash machine sounds odd (the whisk is running hard): Disassemble the
fitting plate and ensure that potato mash has not dried in behind this.
If so, clean, refit the parts and try again.
If this does not help - contact the servicing company stated.
•
Water dripping from the whisk housing. This is a sign that the valve
that controls the amount of water for each portion is worn.
This must be rectified by a servicing company certified by Crem International AB.
13.
8. Programming.
Fast Mash New
PROGRAMMING use code, adjust the recipe value
To open the menu, follow the instructions below. The pin code is 1000.
Remember to always confirm your selection by pressing button
1. Press button
2. Press button
until the display shows.
Service mode:
Recipes
3. Press button
to enter the menu. The display reads PIN CODE IIII.
PIN code= IIII
4. Press button
once and the marker moves to the next digit.
PIN code= IIII
5. Press button
and the second digit shows 0.
PIN code= I0II
6. Confirm by pressing button
.
14.
8. Programming.
Fast Mash New
PROGRAMMING use code.
7. Press button
and the second digit shows 0.
PIN code= I00I
8. Confirm by pressing button
9. Press button
.
and the second digit shows 0.
PIN code= I000
10. Confirm by pressing button
11.
.
The display reads PIN ok.
PIN code= I000
PIN ok
12.
Display shows select drink = 1
Select drink = 1
15.
8. Programming.
Fast Mash New
PROGRAMMING: adjust the recipe value
Select drink = 1
13. Select drink by pressing button
or button
Select drink 1
Select drink 2
Select drink 3
Select drink 4
14.
Confirm the selected drink to be adjusted by pressing button
Set and adjust the recipe value, see chart on pages 17 and 18.
In order to adjust the recipe value for drink 1
15. Press button
to enter the menu. The display shows
Drink 1
start V1 Water 1
16.
To adjust, press button
the display shows.
Drink 1
start V1 W 1 =
0,0
17.
Press button
or
to adjust a new value.
18.
Confirm the new settings by pressing the
19.
Press button
or
.
to go to the different values.
Repeat steps 16-18 to change.
20.
Press button
to go back one level in the menu.
21.
To return to the operating level, press button again.
22.
Select a new drink to adjust the recipe value.
16.
8. Programming.
Chart
Fast Mash New
PROGRAMMING: adjust the recipe value
Serving portion
Basic setting.
Large Mash 1
240 gr 180 ml
Start 1 Stop 1 Start 2 Stop 2
V1
0,0
6,5
0,2
6,0
0,1
8,4
8,3
8,7
V2
Ingred 1
Ingred 2
Mixer 1
Mixer 2
Small mash 2
140 gr, 120 ml
Start 1 Stop 1 Start 2 Stop 2
V1
0,0
4,0
0,2
3,8
0,1
6,2
6,0
6,4
V2
Ingred 1
Ingred 2
Mixer 1
Mixer 2
17.
8. Programming.
Chart recipe
Fast Mash New
PROGRAMMING:
RINSING
Button 4
Start 1 Stop 1 Start 2 Stop 2
V1
0,2
3,5
0,5
4,0
4,5
5,0
V2
Ingred 1
Ingred 2
Blender 1
Blender 2
18.
9. Reset the cup counter.
Fast Mash New
Cup counter:
The machine has a built-in Cup Counter that can be reset.
1
5
3
000
4
2
Reset the cup counter:
1.
Remove the concentrate container. The display shows number of cups.
2.
To reset the counter: Press button
3.
Press button
4.
Confirm the new setting by pressing button
to position Reset Counters.
to reset the counter.
19.
.
10. Storage / Transportation.
Fast Mash New
Long-term storage and transportation
1.
2.
Switch off the machine, unplug it and close the water tap.
The machine must not be stored in freezing temperatures, and all water must
removed before long-term storage.
Emptying the water tank.
1.
Shut off the machine. Switch of the water tap for the machine.
Note: Remember that the water in the tank is very hot.
2.
Loosen the water hook-up (1) and unplug the power cord (2).
3.
Next pull out the service plug (3) located on the back of the machine.
Water hook-up (1)
Service plug (3)
Emptying of water tank
20.
Power connection (2)
11. Dimension sketch.
Fast Mash New
21.
12. Cleaning and care.
Fast Mash New
To clean the outside of the machine, use a soft
cloth and a non-abrasive liquid detergent.
22.
FOR SERVICE
Please contact your dealer
Your Dealer
...............................................................................
...............................................................................
...............................................................................
Crem International AB
Box 960, 671 29 ARVIKA, Sweden
Phone: +46 570 477 00, Fax: +46 (0)570-47719
E-mail: info.se@creminternational.com www.creminternational.com
Item no. 1730096-02