Owners Manual - Philips Parts and Accessories

Register your product and get support at
02
English
www.philips.com/welcome
Type HD8750
02
EN
USER MANUAL
PLEASE READ THIS USER MANUAL CAREFULLY BEFORE USING THE MACHINE
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do not immerse
cord, plugs, or appliance in water or other liquid.
4. Close supervision is necessary when the appliance is used by or near
children.
5. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair
or adjustment.
7. The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Always attach plug to appliance first, then plug cord into wall outlet. To
disconnect, turn any control to “off”, then remove plug from wall outlet.
12. Do not use appliance for other than intended use.
13. Save these instructions.
SAVE THESE INSTRUCTIONS
CAUTION
This appliance is for household use only. Any servicing, other than cleaning
and user maintenance, should be performed by an authorized service center.
Do not immerse machine in water. To reduce the risk of fire or electric shock,
do not disassemble the machine. There are no parts inside the machine
serviceable by the user. Repair should be done by authorized service personnel
only.
1. Check voltage to be sure that the voltage indicated on the nameplate
corresponds with your voltage.
2. Never use warm or hot water to fill the water tank. Use cold water only.
3. Keep your hands and the cord away from hot parts of the appliance during
operation.
4. Never clean with scrubbing powders or harsh cleaners. Simply use a soft
cloth dampened with water.
5. For optimal taste of your coffee, use purified or bottled water. Periodic
descaling is still recommended every 2-3 months.
6. Do not use caramelized or flavored coffee beans.
INSTRUCTIONS FOR THE POWER
SUPPLY CORD
A. A short power-supply cord (or detachable power-supply cord) is to be
provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.
B. Longer detachable power-supply cords or extension cords are available
and may used if care is exercised in their use.
C. If a long detachable power-supply cord or extension cord is used,
1. The marked electrical rating of the detachable power-supply cord or
extension cord should be at least as great as the electrical rating of the
appliance
2. If the appliance is of the grounded type, the extension cord should be a
grounding-type 3-wire cord, and
3. The longer cord should be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children or tripped
over.
2
ENGLISH
Congratulations on your purchase of Saeco Intuita full automatic espresso machine!
To fully benefit from the support that Saeco offers, please
register your product at www.philips.com/welcome.
This user manual applies to HD8750.
The espresso machine is suitable for preparing espresso coffees using whole coffee beans. In this user manual you will
find all the information you need to install, use, clean and
descale your machine.
ENGLISH
CONTENTS
IMPORTANT..................................................................................................... 4
Safety instructions .......................................................................................................................... 4
Warning .......................................................................................................................................... 4
Caution ........................................................................................................................................... 5
Compliance with standards ............................................................................................................ 5
INSTALLATION ................................................................................................. 6
Product overview ............................................................................................................................ 6
General description ......................................................................................................................... 7
PREPARING FOR USE ........................................................................................ 8
Machine packaging ......................................................................................................................... 8
Machine installation....................................................................................................................... 8
USING THE MACHINE FOR THE FIRST TIME ........................................................10
Circuit priming .............................................................................................................................. 10
Automatic rinse/self-cleaning cycle .............................................................................................. 11
Manual rinse cycle......................................................................................................................... 12
“INTENZA+” WATER FILTER INSTALLATION .......................................................13
ADJUSTMENTS ................................................................................................14
Saeco Adapting System ................................................................................................................. 14
Adjusting the ceramic coffee grinder ............................................................................................ 14
Adjusting the aroma (coffee strength) .......................................................................................... 15
Adjusting the dispensing spout..................................................................................................... 16
Adjusting the coffee lenght ........................................................................................................... 17
ESPRESSO AND COFFEE BREWING ....................................................................18
Espresso and Coffee Brewing Using Coffee Beans. ......................................................................... 18
STEAM DISPENSING /CAPPUCCINO BREWING....................................................19
HOT WATER DISPENSING .................................................................................21
CLEANING AND MAINTENANCE ........................................................................22
Daily cleaning of the machine ....................................................................................................... 22
Daily cleaning of the water tank.................................................................................................... 23
Daily cleaning of the Pannarello.................................................................................................... 23
Weekly cleaning of the machine ................................................................................................... 23
Weekly cleaning of the Pannarello ................................................................................................ 24
Weekly cleaning of the brew group .............................................................................................. 24
Monthly lubrication of the brew group ......................................................................................... 27
Monthly cleaning of the coffee bean hopper ................................................................................. 28
DESCALING.....................................................................................................29
MEANING OF THE LIGHT SIGNALS .....................................................................32
Control panel................................................................................................................................. 32
TROUBLESHOOTING ........................................................................................35
ENERGY SAVING ..............................................................................................37
Stand-by ....................................................................................................................................... 37
Disposal ........................................................................................................................................ 37
TECHNICAL SPECIFICATION ..............................................................................38
GUARANTEE AND SERVICE ...............................................................................38
Guarantee ..................................................................................................................................... 38
Service .......................................................................................................................................... 38
ORDERING MAINTENANCE PRODUCTS .............................................................39
3
4
ENGLISH
IMPORTANT
Safety instructions
This machine is equipped with safety features. Nevertheless read the safety
instructions carefully and only use the machine as described in these
instructions to avoid accidental injury or damage.
Keep this user manual for future reference.
The term WARNING and this sign warn against possible severe injuries,
danger to life and/or damage to the machine.
The term CAUTION and this sign warn against slight injuries and/or damage to the machine.
Warning
•
Connect the machine to a wall socket which is properly wired. Its main
voltage should comply with the technical data of the appliance.
•
Do not let the mains cord hang over the edge of a table or counter, or
touch hot surfaces.
•
Never immerse the machine, mains plug or mains cord in water (danger of electrical shock).
•
Never direct the hot water jet towards body parts (danger of burning).
•
Do not touch hot surfaces. Use handles and knobs.
•
Remove the mains plug from the wall socket:
-
If a disturbance occurs.
If the machine will not be used for a long time.
Before cleaning the machine.
Pull on the plug, not on the mains cord. Do not touch the mains plug
with wet hands.
•
Do not use the machine if the mains plug, the mains cord or the machine itself is damaged.
•
Do not make any modifications to the machine or its mains cord. Only
have repairs carried out by a service centre authorized by Philips to
avoid a hazard.
•
This machine is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the machine by a person responsible for
their safety.
•
Children should be supervised to ensure that they do not play with the
machine.
ENGLISH
•
5
Never insert fingers or other objects into the coffee grinder.
Caution
•
The machine is for household use only. It is not intended for use in environments such as staff kitchens of shops, offices, farms or other work
environments.
•
Always put the machine on a flat and stable surface.
•
Do not place the machine on a hot plate, directly next to a hot oven,
heater or similar source of heat.
•
Only put coffee beans into the coffee bean hopper. If ground coffee,
instant coffee or any other substance is put in, it may damage the
machine.
•
Allow the machine to cool before putting on or taking off .
•
Never use warm or hot water to fill the water tank. Use cold water only
•
Never clean with scrubbing powders or harsh cleaners. Simply use a
soft cloth dampened with water.
•
Descale your machine regularly. The machine indicates when descaling is needed. Not doing this will make your appliance stop working
properly. In this case repair is not covered under your warranty!
•
Do not keep the machine at temperature below 0 degree Celsius.
Residue water in the heating system may freeze and cause damage.
•
Do not leave water in the water tank when the machine is not used
over a longer period of time. The water can become contaminated. Use
fresh water every time you use the machine.
Compliance with standards
The machine complies with art.13 of the Italian Legislative Decree dated 25
July 2005, no. 151 “Implementation of the directives 2005/95/EC, 2002/96/
EC and 2003/108/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment, as well as waste disposal”.
This machine complies with EU directive 2002/96/EC.
6
INSTALLATION
Product overview
1
2
3
10
11 12
4
5
6
7
8
13
14
20
15
16
17
9
18 19
33
22
23
24
21
26
25
32
27 28
29
30 31
ENGLISH
General description
1. Grinder adjustment knob
2. Coffee bean hopper
3. Coffee bean hopper lid
4. Control panel
5. Dispensing spout
6. Cup holder grill
7. Full drip tray indicator
8. Drip tray
9. Grease for the brew group
10. Coffee grounds drawer
11. Brew group
12. Coffee residues drawer
13. Service door
14. Power cord
15. Wand protective gripper
16. Pannarello (for hot water/steam wand)
17. Water tank
18. Power cord socket
19. Power button
20. Coffee grinder adjustment key
21. “No water” light
22. “Warning” light
23. “Double coffee” light
24. “No coffee” light
25. “Coffee grounds drawer” light
26. ON/OFF button
27. Hot water dispensing button
28. Espresso brew button
29. “Aroma” selector switch
30. Coffee brew button
31. Steam dispensing button
32. Descaling button
33. Descaling solution -to be purchased separately
7
8
ENGLISH
PREPARING FOR USE
Machine packaging
The original packaging has been designed and constructed to protect the
machine during transport. We recommend keeping the packaging material
for possible future transport.
Machine installation
1 Remove the drip tray with grill from the packaging.
2 Remove the machine from the packaging.
3 For best use, it is recommended to:
•
•
•
Choose a safe, level surface, where there will be no danger of overturning it or being injured.
Choose a location that is sufficiently well-lit, clean and near an
easily reachable socket.
Allow for a minimum distance from the sides of the machine as
shown in the illustration.
4 Attach the drip tray with grill on the machine. Make sure it is fully inserted.
Note:
The drip tray collects the water that comes out of the dispensing spout
during each rinse/self-cleaning cycle as well as coffee that might be spilled
during beverage preparation. Empty and clean the drip tray daily and each
time the full drip tray indicator is raised.
Caution:
NEVER remove the drip tray when the machine has just been turned
on. Wait a couple of minutes, since the machine will carry out a rinse/
self-cleaning cycle.
ENGLISH
9
5 Remove the water tank
1
2
6 Rinse the water tank under fresh water.
7 Fill the water tank with fresh water up to the MAX level and reinsert it
into the machine. Make sure it is fully inserted.
Caution:
Never fill the water tank with warm, hot, sparkling water or any other
liquid, as this may cause damage to the water tank and the machine.
8 Remove the coffee bean hopper lid and slowly pour the coffee beans
into the coffee bean hopper.
Note:
Do not pour too many coffee beans into the coffee bean hopper as this will
reduce the grinding performance of the machine.
Caution:
Only coffee beans must be put into the coffee bean hopper. Ground
coffee, instant coffee, caramelized, flavored coffee or any other object
may damage the machine.
9 Put the lid on the coffee bean hopper.
10 Insert the plug into the socket located on the back of the machine.
1
11 Insert the plug of the other end of the power cord into a wall socket
with suitable power voltage.
2
10
ENGLISH
12 Switch the power button located on the back of on the machine to “I”.
13 The “
” button flashes on the control panel. Press the “
turn on the machine.
” button to
14 The “
” and “ ” lights and the “
” button light will begin to flash
quickly indicating that the water circuit must be primed.
USING THE MACHINE FOR THE FIRST TIME
When using the machine for the first time, the following activities need to
happen:
1) You need to prime the circuit.
2) The machine will perform an automatic rinse/self-cleaning cycle.
3) You need to initiate a manual rinse cycle.
Circuit priming
During this process fresh water flows through the internal circuit of the
machine and the machine warms up. This takes a few minutes.
1 Place a container under the Pannarello.
ENGLISH 11
2 Press the “
” button to start the cycle. The machine starts the automatic priming of the circuit by dispensing some water through the
Pannarello.
3 When the process is completed, the “
”and “
” buttons flash. The
machine is in warm-up mode.
Automatic rinse/self-cleaning cycle
When warm-up is completed, the machine automatically performs a rinse/
self- cleaning cycle of the internal circuit with fresh water. This takes less
than a minute.
4 Place a container under the dispensing spout to catch the small
amount of water which will be dispensed.
5 The “
” and “ ” buttons flash during the whole process. Wait for the
cycle to finish automatically.
6 Wait for the cycle to finish automatically.
Note:
You can stop dispensing as well, by pressing either the “
ton.
” or “
7 When the above steps are complete, check that the buttons “
“
”“
” flash steadily.
” but-
”,“
”,
12
ENGLISH
Manual rinse cycle
During this process you brew a coffee and fresh water flows through the
steam/hot water circuit. This takes a few minutes.
1 Place a container under the dispensing spout.
2 Check that the “
3 Press the “
”, “
”, “
”“
” lights flash steadily.
” button. The machine starts dispensing water.
4 When the dispensing has finished, empty the container.
Repeat the operations from step 1 to step 3 twice, then continue with
step 5.
5 Place a container under the Pannarello.
6 Press the “
” button to start dispensing hot water.
7 Dispense water until the no water light “
” shines steadily.
8 At the end, fill the water tank again up to the MAX level. Now the the
machine is ready for brewing coffee.
Note:
When you haven’t used the machine for 2 or more weeks, the machine
will automatically perform an automatic rinse/self-cleaning cycle after
you switch it on. Thereafter you need to initiate the manual rinse cycle as
described above.
The automatic rinse/self-cleaning cycle is also initiated automatically when
starting up the machine (with cold boiler), when the machine is preparing
to go into stand-by mode, or you have pressed the “ ” button (after a
coffee has been brewed).
ENGLISH 13
“INTENZA+” WATER FILTER INSTALLATION
We recommend you to install the “INTENZA+” water filter as this prevents
lime scale to build up in your machine and preserves a more intense aroma
to your espresso coffee.
You can purchase separately the INTENZA+ water filter. Please refer to the
maintenance products page in this user manual for further details.
Water is a crucial part of every espresso, so it’s most important to always
have it professionally filtered. Using the “INTENZA+” water filter will prevent
mineral deposits from building up and improve your water quality.
1 Remove the small white filter from the water tank and store it in a dry
place.
2 Remove the “INTENZA+” water filter from its packaging, immerse it vertically (with the opening positioned upwards) in cold water and gently
press the sides so as to let the air bubbles out.
3 Set the filter according to the water hardness of the area where you
live. These settings are specified on the filter package.
A = Soft water
B = Hard water (standard)
C = Very hard water
4 Put the filter into the empty water tank. Press it until it cannot move
further down.
14
ENGLISH
5 Fill the water tank with fresh water and reinsert it into the machine.
Write down the date of the next water filter replacement (+ 2 months).
6 Dispense the entire water tank by using the hot water function (see
chapter “Hot water dispensing”).
7 Fill the water tank again.
ADJUSTMENTS
The machine allows for certain adjustments so that you can brew the best
tasting coffee possible.
Saeco Adapting System
Coffee is a natural product and its characteristics may change according to
its origin, blend and roast. The machine is equipped with a self-adjusting
system that allows the use of all types of coffee beans available on the
market (not for caramelized beans).
The machine automatically adjusts itself after brewing several cups of
coffee to optimize the extraction of the coffee to the compactness of the
ground coffee.
Adjusting the ceramic coffee grinder
Ceramic coffee grinders always guarantee accurate grinding for every
coffee blend and prevent the beans from overheating.
This provides for full aroma preservation, delivering the truly Italian taste in
every cup.
Warning:
The ceramic coffee grinder contains moving parts that may be dangerous. Therefore, do not insert fingers and/or other objects. Only adjust
the ceramic coffee grinder using the grinder adjustment key. Turn
off the machine by pressing the ON/OFF button and remove the plug
from the socket before carrying out any type of operation inside the
coffee bean hopper.
You can adjust the ceramic grinders to set the coffee grinding to your
personal taste.
Warning:
The grinder adjustment knob, inside the coffee bean hopper, must be
turned only when the ceramic coffee grinder is working.
ENGLISH 15
This adjustment can be carried out by pressing and turning the grinder adjustment knob inside the coffee bean hopper, using the grinder
adjustment key provided with the machine.
1 Press and turn the grinder adjustment knob one notch at a time. You
will taste the difference after brewing 2-3 cups of espresso.
2 The reference marks inside the coffee bean hopper indicate the grind
setting. There are 5 different grind settings to choose from:
1
2
1 - Coarse grind: lighter taste, for dark roasted coffee blends
to
2 - Fine grind: bolder taste, for light roasted coffee blends
When you adjust the ceramic coffee grinder to a finer setting, your coffee
will taste stronger. For a milder coffee taste, adjust the ceramic coffee
grinder to a coarser setting.
Adjusting the aroma (coffee strength)
Choose your favorite coffee blend and adjust the amount of coffee to be
grounded until they meet your personal taste.
Note:
Selection must be made prior to selecting coffee.
You can chose from three aroma’s by turning the knob. The aroma changes
according to the selected position:
= Mild Aroma
= Medium Aroma
= Strong Aroma
16
ENGLISH
Adjusting the dispensing spout
The height of the dispensing spout can be adjusted to better fit the
dimensions of the cups that you wish to use.
Move the dispensing spout up or down with your fingers to adjust its
height as shown in the image.
The recommended positions are:
For the use of small cups;
For the use of large cups.
Two cups can be placed under the dispensing spout to brew two cups of
coffee at the same time.
ENGLISH 17
Adjusting the coffee lenght
The machine allows you to adjust the amount of brewed espresso according to your taste and the size of your cups.
” button or “
” button is pressed, the machine brews
Each time the “
a pre-set amount of coffee. Each button may be individually programmed
for a specific brew setting.
The following procedure describes the programming of the “
” button
1 Place a cup under the dispensing spout.
2 Press and hold the “
” button. The “
” button and the light “
flash during this phase. Then release the button. The machine is now
programming.
The machine starts brewing coffee.
3 As soon as the desired amount of coffee in the cup is reached, press
the “
” button again.
At this point the button “
” is programmed; each time it is pressed,
the machine will brew the same amount of espresso that was just
programmed.
Note:
” coffee button, the same steps should be followed.
To program the “
” button to stop brewing coffee when the desiYou should using the “
red amount of coffee is reached.
”
18
ENGLISH
ESPRESSO AND COFFEE BREWING
Espresso and Coffee Brewing Using Coffee Beans.
Before brewing coffee, make sure that the water tank and coffee bean
hopper are filled.
1 Turn the aroma selector switch to select the desired aroma.
2 Place 1 or 2 cups under the dispensing spout.
3 Press the “
” button for an espresso or the “
” button for a coffee.
4 To dispense 1 cup of espresso or coffee, press the desired button once.
5 To dispense 2 cups of espresso or coffee, press the desired button
twice consecutively. The light“
” turns on.
Note:
In this operating mode, the machine automatically grinds and doses the
correct amount of coffee. Brewing two espressos requires two grinding
and brewing cycles, automatically carried out by the machine.
ENGLISH 19
6 After the pre-brewing cycle, coffee begins to pour out of the dispensing spout.
7 Coffee brewing stops automatically when the pre-programmed level is
reached; however, it is possible to stop earlier by pressing the button
” espresso button or “
” coffee button).
again (“
STEAM DISPENSING /CAPPUCCINO BREWING
Warning:
Danger of scalding! Dispensing may be preceded by small jets of hot
water. The hot water/steam wand may reach high temperatures. Never
touch it with bare hands. Use the appropriate protective handle only.
1 Fill 1/3 of a container with cold milk.
Note:
Use cold (~5°C / 41°F) milk with a protein content of at least 3% to ensure
optimum results when preparing a cappuccino. You can use whole milk or
low-fat milk depending on your personal taste.
2 Immerse the Pannarello in milk.
3 Press the “
” button.
20
ENGLISH
4 The machine warms-up and the “
”“
” buttons flash. The “
”
button turns off.
5 When the “
” button turns on again, the steam dispensing starts.
6 Froth the milk by gently swirling the container and moving it up and
down.
7 When the milk froth has the desired consistency, press “
” button to
stop dispensing steam.
Caution:
After frothing the milk, clean the Pannarello by dispensing a small
amount of hot water into a container. For detailed cleaning instructions please see the “Cleaning and Maintenance” chapter.
Note:
After dispensing steam, it is possible to brew an espresso or dispense hot
water straight after.
ENGLISH 21
HOT WATER DISPENSING
Warning:
Danger of scalding! Dispensing may be preceded by small jets of hot
water. The hot water/steam wand may reach high temperatures: never
touch it with bare hands. Use the appropriate protective handle only.
”, “
Before dispensing hot water, check that the “
are shining steadily and the water tank is filled.
”, “
”, “
” lights
1 Place a container under the Pannarello.
2 Press the “
” button to start dispensing hot water.
3 The machine warms-up and the “
”“
” buttons flash. The “
”
button turns off.
4 When the “
” button turns on again, the hot water dispensing starts.
5 Pour the desired amount of hot water. To stop the hot water dispensing, press the “
” button.
22
ENGLISH
CLEANING AND MAINTENANCE
Daily cleaning of the machine
Caution:
Timely cleaning and maintenance of your machine is very important
as it prolongs the life of your machine. Your machine gets exposed to
moist, coffee and lime scale continuously!
In this chapter it is described in detail which activities you need to
perform at which frequency. Not doing this will ultimately make your
machine stop working properly. This repair is NOT covered by your
warranty!
-
Note:
Use a soft, dampened cloth to clean the machine.
Do not wash any of its parts in the dishwasher.
Do not immerse the machine in water
Do not use alcohol, solvents, and/or abrasive objects to clean the
machine.
Do not dry the machine and/or its components using a microwave
and/or standard oven.
1 Empty and clean the coffee ground drawer daily with the machine
turned on.
Other maintenance operations can only be carried out when the machine
is turned off and unplugged.
2 Empty and clean the drip tray. Perform this operation also when the
full drip tray indicator is raised.
ENGLISH 23
3 Empty and clean the coffee residues drawer located in side of the machine. Open the service door, remove the drawer and empty the coffee
residues.
Daily cleaning of the water tank
1 Remove the small white filter or the INTENZA+ water filter (if installed)
1
from the water tank and wash it with fresh water.
2
2 Put the small white filter back or the INTENZA+ water filter (if installed)
in its housing by gently pressing and turning it at the same time.
3 Fill the water tank with fresh water.
Daily cleaning of the Pannarello
It is important that you clean the Pannarello daily or after each use as it
preserves hygiene and ensures perfect milk froth consistency.
Each time after frothing milk you need to:
Remove the external part of the Pannarello and wash it with fresh water.
Weekly cleaning of the machine
Clean the seat of the drip tray.
24
ENGLISH
Weekly cleaning of the Pannarello
The weekly cleaning is more thorough where you need to disassemble all
parts of Pannarello.
You need to perform the following cleaning operations:
1 Remove the external part of the Pannarello. Wash it with fresh water.
2 Remove the upper part of the Pannarello from the hot water/steam
wand.
3 Wash the upper part of the Pannarello with fresh water.
4 Clean the hot water/steam wand with a wet cloth to remove milk
residues.
5 Put the upper part back in the hot water/steam wand (make sure it is
completely inserted).
6 Reassemble the external part of the Pannarello.
Weekly cleaning of the brew group
The brew group should be cleaned every time the coffee bean hopper is
filled or at least once a week.
1 Turn off the machine by pressing the “
from the socket.
” button and remove the plug
ENGLISH 25
2 Remove the coffee grounds drawer. Open the service door.
3 Remove and clean the coffee residues drawer.
4 To remove the brew group, press the «PUSH» button and pull it by the
handle.
5 Thoroughly wash the brew group with lukewarm water and carefully
clean the upper filter.
Caution:
Do not use detergent/ soap to clean the brew group.
6 Let the brew group air-dry thoroughly.
7 Thoroughly clean the inside of the machine using a soft, dampened
cloth.
8 Make sure the brew group is in the rest position; the two reference signs
must match. If they do not match, proceed as described in step (9).
26
ENGLISH
9 Gently pull down the lever until it is in contact with the brew group
base and the two reference signs on the side of the brew group do
match.
10 Make sure the hook to lock the Brew Group is in the correct position
by firmly pressing the “PUSH” button until you hear a click. Check if the
hook is at the top end position. If it is not, please try again.
11 Insert the Brew Group in its seat again until it locks into place without
pressing the “PUSH” button.
12 Insert the coffee residues drawer and close the service door.
ENGLISH 27
13 Insert the coffee grounds drawer.
Monthly lubrication of the brew group
Lubricate the brew group after approximately 500 cups of coffee or once a
month.
You can purchase separately the Saeco grease to lubricate the brew group.
Please refer to the maintenance products page in this user manual for
further details.
Caution:
Before lubricating the brew group, clean it under fresh water and let it
dry, as described in the “Weekly cleaning of the brew group” chapter.
1 Apply the grease evenly on both side guides.
28
ENGLISH
2 Lubricate the shaft too.
3 Insert the brew group in its seat until it locks into place. (see “Weekly
cleaning of the brew group” chapter). Insert the coffee residues drawer.
4 Close the service door and insert the coffee ground drawer.
Monthly cleaning of the coffee bean hopper
Clean the coffee bean hopper once a month when it is empty with a damp
cloth to remove coffee oil. Thereafter refill it with coffee beans.
ENGLISH 29
DESCALING
The descaling process takes approx. 35 minutes.
Lime scale builds up inside the machine during use. It needs to be removed regularly as it may clog the water and coffee circuit of your machine.
” light shines
The machine tells you when descaling is needed. If the “
steadily, it means that you need to descale.
Caution:
Not doing this will ultimately make your machine stop working properly, and in this case repair is NOT covered by your warranty.
Use the Saeco decalcifier only. Its formula has been designed to ensure
better machine performance.
You can purchase separately the SAECO decalcifier. Please refer to the
maintenance products page in this user manual for further details.
Warning:
Never drink the decalcifier or any products dispensed until the cycle
has been carried out to the end. Never use vinegar as a decalcifier.
Note:
During the descaling cycle do not switch off the machine .If this has happened you need to restart the descaling cycle from the very beginning.
To execute the descaling cycle, follow the steps below:
Before descaling:
1 Empty the drip tray.
2 Remove the Pannarello from the hot water/steam wand.
30
ENGLISH
3 Remove the “INTENZA+” water filter from the water tank if it was installed.
4 Remove the water tank and pour the entire content of the Saeco decalcifier. Then fill the water tank with fresh water up to the MAX level.
5 Place the water tank back into the machine.
6 Place a large container (1,5 lt) under both the steam/hot water wand
and the dispensing spout.
7 Press and hold the “
” for 3 seconds. When the button starts
” button flashes during
flashing, release it to start the cycle. The “
the whole descaling cycle.
Note:
If you press the “
” button by mistake, press the “
” button to quit.
8 The machine starts dispensing the descaling solution through the
” button flashes) and the dispensing
steam/hot water wand (the “
” button flashes).
spout (the “
Note:
” button. To
The descaling cycle may be paused by pressing the “
” button again. This allows you to empty
resume the cycle, press the “
the container or to stay away from the machine for a brief period of time.
9 When the descaling solution is finished, the “
“
” button flashes.
” light turns on and the
ENGLISH 31
10 Remove the water tank, rinse it and fill it up to the MAX level with fresh
water. Place it back into the machine.
11 Empty the drip tray and place it back.
12 Empty the container and place it back under the steam/hot water
wand and the dispensing spout.
13 Press “
” to start the rinsing cycle.
14 When the rinsing is finished, the “
” light turns on and the “
”but-
ton flashes.
15 Remove the water tank, rinse it and fill it up to the MAX level with fresh
water. Place it back into the machine.
16 Empty the drip tray and place it back.
17 Empty the container and place it back under the steam/hot water
wand and the dispensing spout.
18 Repeat steps 13 to 17 once more. Then continue with step 19
19 The machine heats-up and the automatic rinsing cycle starts to prepare for product brewing.
20 The descaling cycle is completed.
21 Place back the “INTENZA+” water filter into the water tank if it was
installed and the Pannarello.
Note:
At the end of the descaling cycle, wash the brew group as described in the
“Weekly Cleaning of the Brew Group” chapter.
The two rinse cycles are performed in order to have the circuit cleaned
with a preset amount of water to ensure proper machine performance.
If the water tank is not filled up to MAX level, the machine might require
three or more cycles.
32
ENGLISH
MEANING OF THE LIGHT SIGNALS
Control panel
“Double coffee” light
“Warning” light
“No coffee” light
“Coffee grounds
drawer” light
“No water” light
ON/OFF button
Descaling button
Hot water dispensing button
Espresso coffee brew button
Steam dispensing button
Long espresso brew button
“Aroma” selector switch
Light Symbols
Meaning
Machine is in stand-by.
Actions
The machine is performing
the rinsing cycle.
The machine ends the cycle automatically. You
” or “ ” .
can stop it earlier pressing either “
Press “
” to turn on the machine.
FLASHING
FLASHING
The machine is warming up
to brew espresso, dispense
hot water or steam.
FLASHING
The machine is ready to use.
STEADY ON
ENGLISH 33
Light Symbols
Meaning
The machine is dispensing
hot water.
STEADY ON
The machine is brewing one
cup of espresso
STEADY ON
The machine is brewing two
cups of espresso.
STEADY ON
The machine is brewing one
cup of coffee.
STEADY ON
The machine is brewing two
cups of coffee.
STEADY ON
The machine is programming the amount of espresso to brew .
FLASHING
The machine is programming the amount of coffee
to brew .
FLASHING
Actions
34
ENGLISH
Light Symbols
Meaning
The machine is dispensing
steam/frothing milk.
Actions
The machine needs to be
descaled.
Start the descaling cycle. If you don’t descale
regularly, the machine will stop working
properly. This is not covered by your warranty.
The machine is in the descaling cycle.
You can pause the cycle by pressing the
” button.
“
Prime the circuit
Fill the water tank with fresh water and prime
the water circuit as
described in chapter “Using the machine for
the first time”.
-
Make sure that all components have been
correctly inserted and closed.
STEADY ON
STEADY ON
FLASHING
Close the service door.
Insert the brew group.
FLASHING
The coffee bean hopper is
empty.
Fill the coffee bean hopper with coffee beans
and start the brew cycle again.
STEADY ON
The coffee grounds drawer is Insert the coffee grounds drawer.
not inserted
FLASHING
The coffee grounds drawer
and the drip tray are full.
FLASHING QUICKLY
With the machine turned on, empty the coffee
grounds drawer and the drip tray. If the coffee
grounds drawer is emptied with the machine
turned off , or when the indicator light is not
illuminated, the count of coffee cycles
is not reset. For this reason, the indicator light
to empty the coffee grounds drawer may flash
even when it is not full.
ENGLISH 35
Light Symbols
Meaning
The water tank is empty
Actions
Fill the water tank with fresh water.
A fault has occurred in the
machine and hot water,
steam or espresso cannot be
dispensed.
Turn the machine off after 30-seconds, turn it
back on.
Try this 2 or 3 times.
If the machine does NOT start, contact the
Philips Saeco hotline.
STEADY ON
FLASHING
TROUBLESHOOTING
This chapter summarizes the most common problems you could encounter with your machine. If you are unable to solve the problem with the
information below, visit www.philips.com/support for a list of frequently
asked questions or contact the Philips Saeco hotline in your country. You
find its contact details in the warranty booklet by-packed separately or on
www.philips.com/support.
Machine actions
The machine does not switch
on.
Coffee is not hot enough.
The drip tray gets filled although no water is drained.
light
The fast flashing red
is always displayed on the
machine.
Causes
The machine is not connected to
the electric network.
The cups are cold.
Sometimes water is drained automatically by the machine into the
drip tray in order to manage the
rinsing of the circuits and ensure
optimum machine performance.
The coffee grounds drawer was
emptied with the machine off.
No hot water or steam is
dispensed.
The hole of the steam wand is
clogged.
Coffee does not have enough crema.
(See note)
Pannarello is dirty.
The blend is unsuitable, coffee is
not freshly roasted or the grind is
too coarse.
Solutions
Connect the machine to the electric
network.
Preheat the cups with hot water.
This is seen as normal behavior of
the machine
The coffee grounds drawer must
always be emptied with the machine
light starts
on. Wait until the red
flashing more slowly before refitting
the drawer.
Clean the hole of the steam wand
using a pin.
Make sure that the machine is off
and cold before performing this
operation.
Clean the Pannarello.
Change coffee blend or adjust the
grind as explained in chapter "Adjusting the Coffee Grinder".
36
ENGLISH
Machine actions
The machine takes a long
time to warm up or the
amount of water dispensed
from the wand is too little.
The brew group cannot be
removed.
Causes
The machine circuit is clogged by
limescale.
Solutions
Descale the machine.
The brew group is out of place.
Turn the machine on. Close the service door. The brew group automatically returns to the initial position.
Remove the coffee grounds drawer
before removing the brew group.
It may be necessary to change the
type of coffee or the coffee grinder
settings.
Fill the water tank and prime the
circuit (chapter "Using the machine
for the first time").
Clean the brew group ("Weekly cleaning fo the brew group" chapter).
Prime the circuit (chapter "Using the
Machine of the First Time").
Brew a few cups of coffee as described in chapter "Saeco Adapting
System".
Clean the dispensing spout.
Brew a few cups of coffee as described in chapter "Saeco Adapting
System".
Change coffee blend or adjust the
grind as explained in chapter "Adjusting the ceramic coffee grinder".
Prime the circuit (chapter "Using the
machine for the first time").
Clean the brew group ("Weekly cleaning of the brew group" chapter).
Clean the dispensing spout and its
holes.
The coffee grounds drawer is
inserted.
There is a lot of ground coffee Coffee is not suitable for automaunder the brew group.
tic machines.
The machine grinds the
coffee beans but no coffee
comes out.
(See note)
There is no water.
The brew group is dirty.
The circuit is not primed.
Coffee is too weak.
(See note)
Coffee is brewed slowly.
(See note)
This might occur when the machine is automatically adjusting
the dose.
The dispensing spout is dirty.
This might occur when the machine is automatically adjusting
the dose.
The coffee grind is too fine.
The circuit is not primed.
The brew group is dirty.
Coffee leaks out of the
dispensing spout.
The dispensing spout is clogged.
Note:
These problems can be considered normal if the coffee blend has been
changed or if the machine has just been installed. In this case wait until
the machine performs a self-adjusting operation as described in chapter
“Saeco Adapting System”.
ENGLISH 37
ENERGY SAVING
Stand-by
The Saeco full automatic espresso machine is designed for energy savingproven by the Class A energy label.
After 30 minutes of inactivity, the machine turns off automatically. If a
product has been brewed, the machine performs a rinsing cycle.
In stand-by mode, the energy consumption is below 1Wh.
To turn on the machine, press button (if power button on the back of the
machine is set to “I”). If the boiler is cold the machine performs a rinsing
cycle.
Disposal
Do not throw away the machine with the normal household waste at the
end of its life, but hand it in at an official collection point for recycling. By
doing this, you help to preserve the environment.
-
The packing materials can be recycled.
Machine: unplug the machine and cut the power cord
Deliver the appliance and power cord to a service center or public
waste disposal facility.
This product complies with EU directive 2002/96/EC.
The symbol on the product or on its packaging indicates that this product
may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this
product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
38
ENGLISH
TECHNICAL SPECIFICATION
The manufacturer reserves the right to make changes to the technical
specifications of the product
Nominal Voltage - Power Rating Power Supply
See label on the inside of the
service door
Housing material
Thermoplastic
Size (w x h x d)
256 x 340 x 440 mm
Weight
9 kg
Power Cord Length
1.2 m
Control Panel
Front
Pannarello
Special for cappuccinos
Maximum height of the cup under
the dispensing spout (mm)
110
Water Tank
1.5 litres - Removable
Coffee Bean Hopper Capacity
300 gr
Coffee ground Drawer Capacity
10
Pump pressure
15 bar
Boiler
Stainless steel
Safety mechanisms
Thermal fuse
GUARANTEE AND SERVICE
Guarantee
For detailed information on your warranty and related conditions, please
read the warranty booklet by-packed separately.
Service
We want to ensure that you remain satisfied with your machine. If not done
already, please register your product on www.philips.com/welcome so
that we can stay in contact with you and send you cleaning and descaling
reminders.
If you need service or support, please visit the Philips website at
www.philips.com/support or contact the Philips Saeco hotline in
your country. You find its phone number in the warranty booklet by
packed separately or on www.philips.com/support.
ENGLISH 39
ORDERING MAINTENANCE PRODUCTS
For cleaning and descaling, use Saeco maintenance products only.
You can purchase these at the Philips online shop at www.shop.philips.com/
service, your local dealer or at authorised service centers.
If you have any difficulties obtaining maintenance products for your machine, please contact the Philips Saeco hotline in your country.
You find its contact details in the warranty booklet by-packed separately or
on www.philips.com/support.
Overview of maintenance products
-
Decalcifier CA6700
-
INTENZA+ Water Filter CA6702
-
Grease HD5061
-
Maintenance Kit CA 6706
EN
02
Rev.02
del 15-09-12
02
The manufacturer reserves the right to make changes without prior notice.
www.philips.com/saeco
Download PDF

advertising