PL403A
14 place settings
half-load function
For detailed operating method read the corresponding content on the instruction manual.
Switch on the appliance
Fill the detergent dispenser
Press the On/Off button to switch on the appliance, Open the door.
With each wash cycle.
Compartment
For programmes with pre-wash only.
C
A
(Follow the user instructions!)
Check the rinse aid level
Load the baskets
Select a programme
B
Electric indicator on control panel (if provided).
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
Close the door,turn the Washing Program Selector to select a desired programme.
( See the section entitled“ Operating instruction ”)
Running the dishwasher
Turn on the water tap and press the Start/Pause Button. The machine will start working
after about 10 seconds.
Changing the programme
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Press the On/Off button to stop washing , Then press this button to reset .
3. Turn the selector to select a new programme.
4. Restart the dishwasher.
Add forgotten dishes in the
dishwasher.
1.Press the Start/Pause Button to stop the washing.
2.Open the door a little .
3.After the spray arms stop working, you can open the door
completely.
4.Add forgotten dishes.
5.Close the door
6.Press the Start/Pause Button, the dishwasher will run
after 10 seconds.
If the appliance is switched
off during a wash cycle.
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ..
Switch off the appliance
When the working cycle has finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
Turn off the water tap,
unload the baskets
O pen th e doo r carefu lly.
Hot steam may escape
when the door is opened!
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will also dry better.Unload the appliance, starting from the lower basket.
Dear Customer,
This appliance is in tended to be used in household
and similar applications such as:
-staff kitch en areas in shop s, offices and other
working environme nts;
-farm hous es;
-by clients in hotels, motels and othe r residential
type environments;
-bed and breakfast type environments.
Please carefully read this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Keep it as a refer in the later days.
Pass it on to any subsequent owner of the appliance.
Control Panel...................................................2
Dishwash er Fe atures.................................... ...2
A、F ill the Rinse Aid Dispenser............. ..... .. ... ..3
B、Functio n of Detergent ........ .........................4
Attention before o r after loading the Dishwasher
Ba skets..........................................................6
This manual contains sections on safety Instructions,
Operating Instructions, Installat ion I nstructions and
Tr oubleshooting Tips, etc.
The Method Loading Normal Dishware ..............7
Max. Dishes ...................................................8
Wash Cycle Table...........................................9
Turning on the Appliance................................9
Change the Programme.............. .... ................10
At the End of the Wash Cycle ...........................10
To review the section on troubleshooting Tips
will help you to solve some common problems
by yourself .
If you can not solv e the problems by yourself ,
please ask for the help of professional technicians.
Filtering System.............................................11
Caring for the Dishwasher..................... . .........12
Installation preparation .................................. 13
Aesthetic panel's dimensions and installation ...14
Tension adjustment of the door spring ..............16
Connection of drain hoses .............................. 16
Dishwasher installation steps ......................... 17
About Electricity Connecting...........................18
Cold Water Connection.................................. 19
Start of dishwasher................................ .. ......19
Before calling for service........................... . .....20
Error codes.................................... . ..............21
Technical information.............................. .......22
The manufacturer, following a policy of constant
development a nd u pdating of the product, may
make modifications without giving prior notice.
When using your dishwasher, follow the precautions listed below:
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of an electric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipmentgrounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects on or stand on the
door when it is open. The appliance could tip
forward.
When loading items to be washed :
1) Locate sharp items so that they are not likely
to damage the door seal;
2 ) Warning: Knives and other utensils with
sharp points must be loade d in the basket
with their points down or placed in a
horizontal position.
Check that the detergent comparment is empty
after completion of the wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer's
recommendations.
Use only detergent and rinse additives
designed for an automatic dishwasher.
Never use soap, laundry detergent, or hand
washing detergent in you r dishwasher. Keep
these products out of the reach of children.
Keep children away from detergent and rinse aid,
keep children away from the open door of the
dishwasher, there could still be some detergent
left inside.
Improper connection of the equipment-grounding
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet. Have a proper outlet installed by a
qualified electrician.
This appliance is not intended for use by persons
(including children )with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
Dishwash er detergents are strongly alkaline, they
can be extremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
The door should not be left open,
since this could increase the risk of tripping.
If the s upply cord is damaged, it must be replaced
by the man ufacturer or its serv ice agent or a
similarly qualified person in order to avoid a
hazard.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Please d ispose of packing materials properly.
Use the dishwasher only for its intended function.
During installatio n, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water
mains using new hose sets and that old hose-sets
should not be reused.
The maximum nu mber of place settings to be
washed is 14 .
The maximum pe rmissible inlet water pressure is
1Mpa.
The minimum permissible inlet water pressure is
0.04Mpa .
To get the best performance from your dishwasher, read all operating instructions
before using it for the first time.
Option
6. Delay ind icators: to show the delay time (3h/6h/9h )
1. On/Off Button: To turn on/off the power supply.
7.
Rinse aid warning lights: To show
2. Delay Button : To Press the b utton to delay the washing time. when the dispenser need to be refilled.
3. Option Button: To select Half load and Extra dry function s,
these functions can only be used with programmes
Intensive, Heavy, Normal, Glass and 1 Hour.
8 .Extra Drying indicator :
Extra drying: An increased temperature during the final
rinse to increase drying well. There is a slight increase
4. Program indicators: to show which p rogram you have chosen; in the energy cons umption .
5.Half load indicator : To show when you select the
half load function. If you have only about or less than half
of full load dish es of the dish washer, you can select the
half load function and your desired progra m according to
the dishes contaminated degree.A program select the
half load function, it can save time, energy, and water
compare to the program hasn’t select the half load function.
After the half load function is selected, all the spray arms
are running, yo u can load all the baske ts.
9 Start /Pause Button: To start the selected
washing program or pause the washing program
when the machine is working.
10 Washing Program Selector : To Turn the Selector
to select appropriate Program.
Back View
Front view
1
2
3
7
4
5
8
9
6
11
10
12
1
2
3
Top spray arm
Cutlery ra ck
Upper basket
4
5
6
Inner pipe
Lower basket
Dispenser
7
8
9
Cup s helf
Sp ray arms
Filter assembly
10 Inle t pipe connector
11 Drain pipe
12 Adju ste r
Before using your dishwas her for the first time:
A. Fill th e rinse a id dispenser
B. Fill in detergent
Rinse Aid Dispenser
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can
leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is
designed to use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser.
To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely
black . The volume of the rinse aid container is about 110ml.
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
When to Refill the Rinse Aid Dispenser
If there is no rinse-aid warning lig ht in the control p anel, you can judge the amount of rinse-aid by the color of the
optical level
indicator "C" located next to the cap. When the rinse-aid container is full, the whole indicator will be dark .As the
rinse-aid
diminis hes, the size of the dark dot decreases. You should never let the rinse aid get below 1 / 4 full.
As the rinse aid diminishes, the size of the black dot
on the rinse aid lev el indicator changes, as illustrated be low.
Fu ll
3 / 4 fu ll
1 / 2 fu ll
1 / 4 fu ll - Should refill to eliminate spotting
Empty
RINSE AID DISPENSER
1
2
3
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any spills
with a damp cloth. Don't forget to replace the cap before you close dishwasher door.
Attention!
Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming
during the next wash.
Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming
during the next wash. Don't forget to repla ce the cap before you close dishwasher door.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or four settings. Always start with the dispenser
set on "4". If spots and poor drying are a pro ble m, increase the amount of rinse
aid dispensed by removing the dispe nser lid and rotating the dial to "5". If the
dishes still are not drying properly or are show sp ots, adjust the dial to the next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or
knife blades.
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher.
Most of the commercial quality detergents are suitable for this purpose.
Detergents
There are 3 sorts of detergents
1.With phosphate and with chlorine
2.With phos phate and without chlorine
3.Without phosphate and without chlorine
Normally new pulveris ed d etergent is without p hosphate. Thus the water softene r function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 °dH. If detergents without phosphate are used in the case of hard water
often white sp ots appear o n dishes and gla sses. In this case please add more detergent to reach
better results. Detergents with out chlorine do only bleach a little. Strong and coloured sp ots will not
be removed completely. In this case please choose a progra m with a higher temp erature.
Concentrated Detergent
Ba sed on their chemical composition, detergents can be split in two basic types:
conventional, alkaline detergents with caustic components
low alkaline concentrated detergents with natural enzymes
Detergent Tablets
Deterg ent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve an d develop their full cleaning power during short
progra ms. Therefore please use long programs when using d etergent tablets, to
ensure the complete removal of detergent residuals.
Detergent Dispenser
Th e dispenser mus t be refilled before the start of each wash cycle following the instructions
provided in the wash cycle table . Your dishwasher uses less detergent and rinse aid than
Conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More h eavily soiled items need more deterge nt. Always add the
detergent just before starting the dishwasher, otherwise it could g et damp and will not
dissolve properly.
Amount of Detergent to Use
If th e lid is close d: press rele ase button. The lid will spring ope n.
Always add the dete rgent just before starting each wash cycle.
Only use branded detergent aid for d ishwash er.
Dishwasher detergent is corrosive! Take care to keep it ou t of reach of c hildren.
Proper Use of De terg ent
Use only deterge nt specifically made for the use in dishwashers. Keep your detergent fresh and dry.
Don't put powdered d etergent into the dispenser until you're ready to wash dishes.
A
B
Fill in Detergent
Fill the detergent dispen ser with detergent.
The marking ind icates the dosing levels , as
illustrated o n the right:
A
The place of main wash cycle detergent placed.
B
The place of pre-wash cycle detergent placed.
Please observe the man ufacturers dosing an d storag e
Recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
deterge nt dose in the pre-wash detergen t ch amber. This detergent will take effect during the pre-wash phase.
You find information abou t the amount of detergent for the single programme on the las t page.
Plea se a ware, that according to the level soiling and the specific hardness of water differences are possible.
Plea se o bserve the manufacturer's recommendations on the detergent packaging.
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further
information from the detergent manufacturers.
For particular items, select a program with as low a temperature as possible.
To prevent damage, do not take gla ss a nd c utlery out of the dishwasher immediately
after the programme h as ended.
Are not suitable
Are of limited suitability
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that are not
temperature resistant
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Some types of glasses can become
dull after a large number of washes
Silver and aluminum parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
(For best performance of the dishwasher, follow these loading guide lines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts o f leftover food. Soften remnants of burnt food in pans.
It is not necess ary to rinse the d ishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots /pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that the spray arms can rotate freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
Load hollow items suc h as cup s, glasses, pans etc. With the opening facing downwards so that
water can not collect in the con tainer or a deep b ase.
Dishes and items of cutlery must not lie ins ide one another, or cover each oth er.
To avoid damage to glasse s, th ey must not touc h.
Load large ite ms which are most difficult to clea n into the lower bask et.
The upper basket is designed to ho ld more delicate and lighter dishware such as glasses , coffee
and tea cups
Long bladed knives stored in an upright position are a potential haza rd!
Long and/or sharp items o f cutlery such as carving kniv es must be positioned
horizonta lly in the upper b asket.
Please do not ove rload yo ur dishwasher. This is important for good results and for
reasonab le consumption of energy.
To prevent water dripping from the uppe r basket into the lower basket, we recommend that you
empty the lower basket first and then the upper basket.
The u pper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and
tea cups and saucers, as well as plates, small bowls
and shallow pans (as long as they are not too dirty).
Position the dishe s an d co okware so that they will
not get moved by the spray of wate r.
We suggest that you place large items and the most difficult
to clea n items into the lower basket: such as pots, pans, lids,
serving dishes and bowls, as shown in the figure below.
It is preferable to place serving dish es a nd lids on the side of
the racks in order to avoid blocking the rotation of the top
spray arm.
Please be reminded that:
Pots, serving bowls, etc, must always be placed top down.
Deep pots should be slan ted to allow water to flow out.
The Botto m Basket features fo lding spikes so that larger or more pots and pans can be loaded.
Adjusting the Upper Basket
Th e height of the upper basket can be ad jus ted in ord er to
create more sp ace for large utensils both for the upp er
/lower basket. The height o f the upper basket can be
adjusted by placing the wheels on different height of the
rails. L ong items, serving cutlery, salad servers and knives
should be placed on the shelf so that they do not obstruct
the rotation of the spray arms..
Folding back the cup shelves
Fo r better stacking of po ts and pans,
the spikes c an b e folded down as
sho wn in the pic ture right.
Folding Spikes of Lower Basket
Fo r better stacking of pots and pans,
the spikes can be folded down as
shown in the picture right.
Cutlery should be placed in the cutlery ra ck separately
from each other in the appropriate positions, and do
make sure the utensils do not nest to gether, this may
cause bad performa nce.
Max. Dishes
Max. Dishes
Top basket
Bottom basket
Lower Position max.Φ
19cm
25cm
Upper Position max.Φ
14cm
30cm
5.Starting a washing program
Wash Cycle Table
NOTE: (
) Means: need to fill rinse into the Rinse-Aid Dispenser.
Cycle Selection
Information
Program
Description
of Cycle
Pre-wash(50 )
Wash (65 )
casserole dishes and dishes Rinse
Rinse
that have been sitting with
Rinse(65 )
dried food on them for a
Drying
while.
Pre-wash(45 )
Wash (55 )
For heavily soiled loads,
such as pots, plates, glasses Rinse
Rinse (60 )
and lightly soiled pans.
Drying
Detergent Running
pre/main time(min)
Energy
(Kwh)
Water
(L)
135
1.4
18
5/27.5g
(Or All in1)
165
1.15
14.5
5/27.5g
(Or All in1)
160
0.87
20g
115
0.8
14.5
5/27.5g
60
0.9
10
40
0.5
10.5
For the heaviest soiled
Intensive loads, such as pots, pans,
Heavy
Normal
(*AS/NZS 2007.1)
Glass
1 Hour
Quick
For normally soiled loads,
such as pots, plates,glasses
and lightly soiled pans.
standard daily cycle.
For lightly soiled loads,
such as glasses,
crystal and fine china.
Pre-wash
Wash (50 )
Rinse
Rinse(50 )
Drying
Pre-wash
wash(40 )
Rinse
Rinse(60 )
Drying
Daily wash in only 1 hour.
For lightly and normally
soiled plates and pans
for everyday.
Pre-wash(50 )
Wash(60 )
Rinse (55 )
Drying
A shorter wash for lightly
soiled loads that do not
need drying.
Wash (40
Rinse
Rinse (45
5/27.5g
(Or All in1)
13.6
)
20g
)
NOTE:
*
: This program is the test cycle. The information for comparability test
in accordance with
, as follows:
Capacity: 14 setting
Position Upper basket: upper wheels on rails
Rinse aid setting: 6
Open the door slightly 50mm to assist in drying of the dishes after every wash
Turning On the Appliance
Starting a cycle wash
1 Draw out the lower and upper basket, load the dishes and push them back.
It is commended to load the lower basket first, then the upper one (see the section entitled
Loading the Dishwasher ).
2 Pour in the detergent (see the section entitled Detergent and Rinse Aid ).
3 Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification
of the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
4 Close the door, press the ON/OFF Button, and the ON/OFF light will turn on.
5 Turn the program Selector clockwise , the wash program will be changed as follows direction:
Intensive->Heavy->Normal->Glass->1Hour->Quick;
If a program is selected, the response light will light. Press the Start/Pause button, the dishwasher
begins to start.
9
Rinse
Aid
When you press the Start/Pause button to pause during washing, the running indicator will
stop blinking and the dishwasher will mooing every minute unless you press the
Start/Pause button to start.
Premise:
A cycle that is underway can on ly be modified if it has only been running for a short time. Otherwise, the
detergent may have already be en released, a nd the appliance may have already drained the wash water.
If this is the case , the detergent dispenser mu st be refilled (see the section entitled " Loading the
Detergent " ).
2 Press the On/Off button to stop washing , Then press this button to reset , Then you can change the progra m to
the des ired cycle setting (see the section entitled " Sta rting a wash cycle. . ." ).
1
If you open the door during a wash cycle , the machine will pause. The program light will
stop blinking and the buzzer will sound every minute unless you close the door . After
you close the door ,the machine will keep on working after 10 seconds.
A forgotten dish can be added any time before the detergent cup opens.
4 Add forgotten dishes.
1 Press the Start/Pause Button to stop the washing.
2 Open the door a little .
5
Close the door
the spray arms stop working, you can open the door
3 After
completely.
6
Press the Start/Pause Button, the dishwasher will run
after 10 seconds.
When the wo rking cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supp ly and open the door of the dishwasher.
Wait for a few minutes before unlo ading th e dishwasher to avoid ha ndlin g the dishes and utensils while they
are still hot and more susceptible to break age. The y will also dry better.
Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressing the ON/OFF button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
Wash th e arms in When
soapy following
and warmthis
water
and use from
a softstep1
brushtotostep 3, the filter system will be removed;
procedure
It is dangerous
tothem
openthoroughly.
the door when washing, because the hot water may scald you.
clean the jets. Replace
them
afteritrinsing
when following
from Step
3 to Step 1, the filter system will be installed.
The filter prevents larger remnants of food or other objects from getting inside the pump.
The residues may block the filter, in this case they must be removed.
The filter system consists of a coarse filter,a flat (Main filter)
And a microfilter(Fine filter).
Main filter
2
1
Fo od and soil particles trap ped in this filter are pulverized by a
specia l jet on the lower spray arm and washed down to drain.
1
Coarse filter
2
La rger ite ms, such as p ieces of bones or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on the top of this
filter and lift out.
3
Fine filter
3
This filter holds soil and food residues in the sump area a nd
preve nts it from being redeposit on the dishes during wa sh cycle.
Filter assembly
The filter efficiently re mo ves food particle s from the wash water, allowing it to be rec ycled during the cycle.
For best performance and results, the filter must be cleaned re gularly. For this reason, it is a goo d idea to
remove the larger food particles trapp ed in the filter after e ach was h cycle by rinsing the semicircular filter and
cup under runnin g water. To remove the filter device, pull the cup handle in the upward d irection.
The d ishwasher must never b e used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
1
Step 1:Turn the filter in anti-clockwise direction,
2
Step 2:lift the filter assy up
When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.
Remarks:
- Inspect the filters for blo cking a fter e very time the dishwa sher has been used.
- By unscrewing the coarse filter, you can remove the filter system. Re move any foo d remna nts and
clean the filters under running water.
The entire filter assembly should be cleaned once a week.
Cleaning the Filter
To clean the coarse filter and the fine filter, use a c leaning b rush. Reassemb le the filter p arts as shown in the figures
on the last page and reinsert the entire assembly in the dis hwa sher, positio ning it in its seat and pressing downwards.
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of the dishwasher could be decreased.
The control panel can be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Cleaning The Door
To clean the e dge around the door, you should use only a soft warm, damp cloth.
To avoid pene tration o f wa ter into the door lock and electrical components, do not
use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door loc k
and electrical components.
Abrasive agents or some paper towels shou ld not be used becau se of the risk of
scratching or leaving spots on the stainless steel surface.
Protect Against Freezing
please take frost protection measures on the dishwasher in winter. Every time a fter washing cycles,
please operate as follows:
1.Cut off the electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain the water from the inlet pipe an d water valve. (Use a pan to gather th e water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
If your dishwasher cannot work because of the ice,
please contact professional service persons.
Cleaning the Spray Arms
It is necessary to clean the spra y arms re gularly fo r hard
wate r che micals will clog the sp ray arm jets a nd bearings.
To remove the up per spray arm, hold the nut, rotate the arm
clockwise to remove it.
To remove th e lower spray arm, pull out the spray arm u pwa rd.
Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.
After Every Wash
When not in Use for a LongTime
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odours are not trapped inside.
It is recommend that you run a was h cy cle with the
dishwasher empty an d the n remove the plug from the
socket, turn off the wa ter supply and leave the door of
the appliance slightly open. This will help the d oor
seals to last longer and prevent odours from forming
within the appliance.
Remove the Plug
Before cleaning or performing maintenance, always
remove the plug from the socket.
No Solvents or Abrasive Cleaning
To cle an the e xterior a nd rubber p arts of the dishwasher,
do not use solvents or abrasive cle aning products.
Only use a clo th with warm so apy water.
To remove spots o r stains from the surface of the
interior, use a cloth da mpened with water a n a little
vinegar, o r a cleaning pro duct mad e specifically for
dishwashers.
The installation of the pipes
and electrical equipments
should be done by p rofessionals .
●
Moving the Appliance
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
Seals
One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
Electrical Shock Hazard
Disconnect electrical power before
installin g dishwasher.
Failure to do so can result in death or
electrica l shock.
Installation preparation
The installation position of dishwasher sho uld be near the existing in let and drain hoses and
power cord.
One side of the ca binet sink should be chosen to facilitate the connection of drain hoses of
the dishwasher.
Note: please check the accomp anying installation accessories(hook for aesthetic panel,screw)
Please carefully read the installation instruction.
●
Illustrations of cabinet dimensions and installation position of the dishwasher
Preparations should be made before moving the dishwasher to the installation place.
Choose a place near the sink to facilitate the installation of inlet and drain hoses
(see figure 1).
If dishwasher is installed at the corner of the cabinet, there should be som e space
(illustrated in figure 2) when the door is opened.
1
2
【Figure1】
Cabinet dimensions
Less than 5mm
between the top
of dishwasher and
cabinet and the
outer door aligned
to cabinet.
90 °
90 °
820mm
580mm
Electrical, drain and
water supply line
entrances
80
100
Space between cabinet
bottom and floor
600 mm
【Figure2】
Minimum space when
the door is opened
Dishwasher
Cabinet
Door of
dishwasher
Minimum space of 50mm
●
1
Aesthetic panel's dimensions and installation
The aesthetic wooden panel could be processed according to the Figure 3.
【Figure3】
The aesthetic panel should
be processed in accordance
with the illustrated dimensions
(Unit: mm)
2 magical
paster A and magical paster B be disjoinedon ,magical paster A on the aesthetic wooden panel and
felted magical paster B of the outer door of dishwasher(see f igure 4a). After positioning of the panel , fix the panel
onto t he outer door by screws and bolts(See figure 4b)
【Figure4a】
Installation of aesthetic panel
【Figure4b】
Installation of aesthetic
wooden panel
1 . take away the four
short screws
2 . pin up the fo ur long
screws
●
Tension adjustment of the door spring
The door springs are set at the factory to the proper tension for the outer door.
If aesthetic wooden panel are installed, you will have to adjust the door spring tension.
Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable
(see figure 5).
Door spring tension is correct when
the door remains horizontal in the
fully opened position,yet rises
to a close with the slight lift of a
finger.
【Figure5】
Tension adjustment
of the door spring
●
Connection of drain hoses
Insert the drain h ose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the ho se must be less than 1000mm.
Front
NOTE
The top of the hose
must be less than
1000mm.
Drain pipe
Counter
A
B
φ 40mm
●
Dishwasher installation steps
1 Install the furniture door to the outer door of the dishwasher using the brackets provided. Refer
to the template for positioning of the brackets.
2 Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to
tighten the left and right door springs. Failure to do this could cause damage to your dishwasher
(Illustration 2) .
3 Connect the inlet hose to the cold water supply .
4 Connect the drain hose. Refer to diagram . (Figure 6)
5 Connect the power cord .
6 Affix the condensation strip under the work surface of cabinet. Please ensure the condensation
strip is flush with edge of work surface.
7 Place the dishwasher into position.(Illustration 4)
8 Level the dishwasher. The rear foot can be adjusted from the front of the dishwasher by turning
the Allen screw in the middle of the base of dishwasher use an Allen key (Illustration 5A). To adjust
the front feet, use a flat screw driver and turn the front feet until the dishwasher is level (Illustration 5B).
9 The dishwasher must be secured in place. There are two ways to do this:
A. Normal work surface:Put the right(left) installation hook into the slot of the right(left) side plane and
secure it to the work surface with two woodscrews (Illustration 6).
B. Marble or granite work top:Bend the right(left) installation hook into right-angle,and put it into the
slot of the right(left) side plane and secure it to the work surface with two woodscrews s (Illustration 7).
【Figure 7】
Dishwasher must be level for proper dish rack operation and wash performance.
1 Place a spirit level on door and rack track inside the tub as shown to check that the
dishwasher is level.
2 level the dishwasher by adjusting the three levelling legs individually.
3 When level the dishwasher, please pay attention not to let the dishwasher tip over.
【Figure 8】
Illustration of feet adjustment
Chec k level Front to Back
NOTE:
The maximum adjustment
height of the feet is 50 mm.
Spirit level
Check level si de to side
For personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANC E.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
Plea se look at the ra ting label to know the rating voltage and connect the dishwash er to the app ropriate power supp ly.
Use the required fuse 10 amp, time delay fuse or circuit breaker rec ommended and provide separate circuit serving
only this appliance.
Ensure the voltage and frequency of the power be ing corresponds to
those on the rating plate. Only insert the plug into an electrical so cket which is earthed
properly. If the electrical socket to which the applianc e must be conne cted is not
appropriate for the plug , replace the socket, rather than using a adaptors or the like as
they could ca use overhea ting and burns.
This appliance must be earthed. In the event
of a malfunction or breakdown, earthing will
reduce the risk of electric shock by providing a
path o f least resistance for the electric current.
This appliance is equipped with a cord having an
equipment-earthin g co nductor and an earthing
plug. The plug must be plugged into an appropriate
outlet that is installed and earthed in accordance
with all local standards and requirements.
Improper connecti on of th e equ ipmentgrounding conductor ca n re sul t i n th e risk
of an electric shock. Che ck wi th a qualified
electrici an or service represe ntativ e if you
are i n doubt whether the app li an ce is properly
grounded. Do not mo dify the plug p rovided w ith
the appliance; If it is n ot fit for the outlet.
Have a proper ou tlet in stalled b y a qualifi ed
electrici an.
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure
that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear. This precaution is needed to avoid the
risk of the water inlet to be blocked and damage the appliance.
please close the hydrant after using.
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can
be positioned either to the right or the left sides to facilitate pro per installation.
How to Drain Excess Water From Hoses
If the sink is 1000mm higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will b e necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Water Outlet
Connect the water d rain hose. The drain hose must be correc tly fitted to av oid wate r leaks.
En sure that the water inlet hose is not kinked or s quashed.
Extension Hose
If you n eed a drain hose extension, make sure to use a similar dra in hose.
It must be no longer than 4 metres; o therwise the cleanin g effect o f the dishwasher could be re duced.
Syphon Connection
Insert the drain hose into a d rain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avo id bending o r crimping it. The top of the hose mus t be less than 100 0mm.
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly
2 The inlet valve is open
3 There is a leakage at the connections of the conducts
4 The wires are tightly connected
5 The power is switched on
6 The inlet and drain hoses are knotted
7 All packing materials and printings should be taken out from the dishwasher
After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
Fuse blown, or the
circuit breaker has
been triggered
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Water pressure is low
Check that the water supply is connected properly and
the water is turned on.
Door of dishwasher
not properly closed.
Make sure to close the door properly and latch it.
Kink in drain hose
Check drain hose.
Filter clogged
Check coarse the filter
(see section titled " Cleaning The Filter ")
Kitchen sink clogged
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Improper detergent
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 1 gallon of cold water to the tub. Close and latch the
dishwasher, then select any cycle. Dishwasher will drain
out the water at the first step.Open the door after draining
is stop and check if the suds has disappeared.
Repeat if necessary.
Spilled rinse-aid
Always wipe up rinse-aid spills immediately.
Detergent with
colourant was used
Make sure that the detergent is the one without
colourant.
Hard water minerals
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
The affected items are
not corrosion resistant.
The items should be corrosion resistant.
A spray arm is
knocking against
an item in a basket
Interrupt the programme, and rearrange the items
which are obstructing the spray arm.
Items of crockery
are loose in the
wash cabinet
Interrupt the programme,
and rearrange the items of crockery.
This may be caused
by on-site installation
or the cross-section of
the piping.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
The dishes were not
loaded correctly.
See notes in " Loading the Dishwasher Baskets ".
The programme was
not powerful enough.
Select a more intensive programme.
See" Wash Cycle Table ".
Not enough detergent
was dispensed.
Use more detergent, or change your detergent.
Items are blocking
the path of spray arms.
Rearrange the items so that the spray can rotate freely.
The filter combination
in the base of wash
cabinet is not clean or
is not correctly fitted.
This may cause
the spray arm jets
to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets. See "Cleaning the Spray
Arms".
Combination of soft
water and too much
detergent.
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Aluminum utensils
have rubbed against
dishes.
Use a mild abrasive cleaner to eliminate those marks.
Dishes block
detergent cups.
Re-loading the dishes properly.
Improper loading
Load the dishwasher as suggested in the directions.
Too little rinse-aid
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Dishes are removed
too soon
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
Wrong program
has been selected
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Use of cutlery with
a low-quality coating
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
When some malfunctions come on, the appliance will display error codes to warn you:
The Rapid light flicker fleetly
Longer inlet time.
Faucets is not opened, or water intake is
restricted,or water pressure is too low.
The Glass light flicker fleetly
Overflow.
Some element of dishwasher leaks .
If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
Height :
Width :
Depth :
815mm
598 mm
550mm ( with the door closed )
Water pressure:
Power supply:
Capacity:
0.04-1.0MPa
see rating label
14 place settings