installation manual

INSTALLATION MANUAL
MOSER STAINLESS STEEL KITCHEN FAUCET
MODEL MANCHESTER
STEP 1SINK SPECIFICATIONS
Thank you for your purchase of a MoSER faucet. With proper care and maintenance, your new faucet will
bring you years of trouble free enjoyment. We welcome any questions or comments you may have and look
forward to assisting you.
For more information about MoSER Sinks and Faucets products, please visit our website at:
www.mosersinks.com
To ensure that your installation proceeds smoothly, please
carefully read the installation and maintenance instructions.
Remember to inspect your faucet for any noticeable damage
and verify all parts and pieces are in the box. Verify all local
applicable plumbing and building codes. The following
instructions are based on application in a residential setting.
For the installation of MoSER stainless steel faucets,
we suggest using only licensed plumbers. Please note
acceptable variances are approximately 1/16 of an inch.
Alignment to the pre-drilled hole cut-out and precise
application and trimming of any adhesive sealant are critical
for a superior fit and finished look. Please take extra care
when installing MoSER stainless steel faucet.
MoSER does not accept any liability for damage to your
countertop, sink fixture, faucets or personal injury during
installation. Warranty is void if installation instructions are not
properly followed.
!
Important note:
i. Ensure that the cold and hot water
lines are turned off.
ii. Wrap all threaded connections
with Teflon tape. Be sure to always
wrap in a clockwise direction.
iii. Cover the sink drain to avoid losing
parts.
iv. Do not disassemble the main
faucet body, as it has been
precision factory assembled.
v. Verify that working pressure is
between 0.05-1.00MPa (including
both hot and cold water) and that
water temperature is between 4oC
and 90oC
Tools and material you may require:
»» Adjustable Wrench
»» Teflon Tape
»» Silicone Adhesive
»» Rags
»» Eye Protection
»» Phillips Screwdriver
»» Pencil (not ink)
»» Denatured Alcohol
»» Tape Measure
Be sure to use proper tools and always wear personal safety devices for your protection.
!
To avoid the risk of fresh water contamination due to back-siphonage,
do not connect this faucet to a portable washing device such as a dishwasher.
STEP 1SINK SPECIFICATIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
Hot and cold waterlines
Hose Clip Holder
Weight
Screws
Lock Nut
Metal Washer
Rubber Ring
Faucet Extender
O-Ring
M15 Adapter
Check Valve
Washer
G1/2 Adapter
Washer
Finishing Cap
M5 Screw
Handle
Cover
Clamp Nut
Ceramic Cartridge
Faucet Body
Gasket
O-Ring
Plastic Gasket
M4 Screw
Spout
Faucet Head
Flex hose
Check Valve
30. Nozzle Adapter
STEP 1SINK SPECIFICATIONS
Faucet Installation:
Depending on the distance between the faucet hole and the wall, two installation methods are possible for
MoSER faucets with side mounted levers.
Method 1 – Distance between hole and wall is greater than 3.5”
If the distance between the faucet hole and the wall is
more than 3.5”, a positioning of the faucet lever parallel to the wall is possible.
Method 2 - Distance between hole and wall is less than 3.5”
If the event the distance between the faucet hole and
the wall is less than 3.5”, a positioning of the faucet
lever 30 degrees to 90 degrees off of the wall may be
required to allow for full operation.
NOTE
If no backsplash is present, make
sure to take into consideration the
thickness of any future backsplash
when determining the distance.
STEP 1SINK SPECIFICATIONS
STEP 1
Insert faucet body in the pre-drilled 1 3/8” hole
STEP 2
Insert plastic faucet extender (8), shim (7), washer (6),
lock nut (5) and lock nut screws (4).
NOTE
Faucet extender is required when
faucet is installed in overmount sinks
and optional when installed in solid
surface countertops.
STEP 1SINK SPECIFICATIONS
STEP 3
Use Phillips Screwdriver to tighten lock nut screws.
STEP 4
Slip Hose Clip Holder (2) on the end of the flex hose.
STEP 1SINK SPECIFICATIONS
STEP 5
Secure check valve assembly onto the extending
pipe. Tighten with adjustable wrench until snug.
Secure the end of the flex hose onto the check valve
assembly and tighten with an adjustable wrench until
snug.
NOTE
Ensure O-rings are present in the
check valve assembly before connecting to hose and extending pipe.
STEP 6
Connect hot and cold waterlines (1) to faucet. Tighten until snug.
Install weight (3) approximately 1.18” (30mm) from
the lowest point on the hose and tighten screws with
a Phillips screwdriver.
STEP 1SINK SPECIFICATIONS
STEP 7
Wrap Teflon tape to the threaded portion of the shut
off valves.
Verify if O-rings are present on both ends of the hot
and cold waterlines.
Connect hot and cold waterlines to the shut off
valves. Tighten with an adjustable wrench until
snug.
Ensure handle is in the “off” position
Turn on water supplies and check for leaks.
NOTE
In the event longer waterlines than
those supplied are required,
installer must purchase additional
parts separately
STEP 8
Turn faucet on and ensure proper flow.
Pull out faucet head and look for any leak.
Turn faucet off.
STEP 1SINK SPECIFICATIONS
STEP 9
Remove spray head and hold tip of spray hose.
Turn faucet on for 1 minute to flush any debris.
Turn faucet off and reconnect spray head.
Legal Disclaimer
All technical data and information provided in this publication is done as a public service to customers of MoSER Sinks and Faucets
(MoSER) and consumers of its products. All names, designs, and model numbers of products are the property of MoSER. Prices and
specifications of MoSER products are subject to change without notice or obligation. MoSER may also change or discontinue models
of its products without notice or obligation. While MoSER endeavors to provide accurate information and descriptions of its products,
accuracy and completeness cannot be guaranteed. MoSER is not responsible for, nor does it have any liability for any mistakes
or typographical errors, including liability for incidental, consequential, or special damages. All products should be inspected and
measured promptly upon delivery and certainly before any improvements or alterations are done in anticipation of or preparation for
installation. MoSER assumes no liability for the use of such information or for any damages incurred through its use or applications.
Nothing contained in this publication is to be construed as contractual or providing any form of warranty or representation on the
part of MoSER. MoSER MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY
OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE, AS TO THE INFORMATION CONTAINED HEREIN OR THE
PRODUCTS DESCRIBED HEREIN.
mosersinks.com