item #0071412 single handle tub &

AquaSource® is a registered trademark
of LF, LLC. All Rights Reserved.
ITEM #0071412
SINGLE HANDLE TUB & SHOWER FAUCET
MODEL # 873-4604
ITEM #0071441
SINGLE HANDLE SHOWER ONLY FAUCET
MODEL # 873-4704
Questions, problems, missing parts?
Before returning to your retailer, call our customer service department
at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday.
1
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
Description
Shower Flange
Shower Arm
Shower Head
Handle
Screw
Escutcheon
Valve Body
Plug
Tub Spout *
Quantity
1
1
1
1
2
1
1
1
1
A
B
C
D
G
F
E
* Not included with shower only faucet.
!
H
I
WARNINGS AND CAUTIONS
• Follow the installation instructions carefully. Proper installation is the installer's responsibility.
• Failure to follow correct installation procedures can result in the faucet being loose, which
can result in serious injury.
• Check local building codes before beginning installation to ensure compliance.
PREPARATION
Before beginning the assembly of product, make sure all parts are present. Compare parts with
package content list and diagram above. If any part is missing or damaged, do not attempt to
assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 180 minutes
Tools Required for Assembly: Phillips Screwdriver, Plumber's Tape, Adjustable Wrench,
Allen Wrench, Hacksaw
Helpful Tools: Adjustable Pliers, Pipe Wrench
*IMPORTANT: Complete valve replacement** is required
for this tub/shower unit. An access hole must be cut with
enough room to install the new tub/shower valve inside
the wall. Professional installation is recommended.
**Valve included
2
0071412
**Valve included
0071441
ASSEMBLY INSTRUCTIONS
1. SHUT OFF WATER SUPPLY.
Verify that the hole sizes and positions of holes in the wall are
corrected.
Recommended component measurements
A.Shower and / or spout outlet hole: 1-1/4 inch diameter.
B.Valve access hole: 6 inch diameter.
Be sure that the black template plate's surface is flush with the
finished exterior surface of the wall. Be sure to position the
valve body correctly in wall. "UP" marking up. The 8 inch
Minimum from the valve body to the tub spout is required for
proper operation.
Fig. 1
1 1/4 inch Dia
30 inch
Shower Only
6 inch Dia
48 inch
Tub&Shower
48 inch
Shower Only
8 inch MIN.
1 1/4 inch Dia
Fig. 2
pipe elbow
shower
outlet pipe
2. SUPPLY CONNECTION LAYOUT
Wrap plumber's tape around pipe threads in a clockwise
direction.
Connect water supplies to left (hot) and right (cold) valve body
(G) inlets. Connect shower outlet pipe and tub outlet pipe to
valve body. Connect Pipe Elbow (not included) to the end of
the pipe.
3. SHOWER ONLY SUPPLY CONNECTION LAYOUT
Wrap plumber's tape around pipe threads in a clockwise
direction.
Connect water supplies to left (hot) and right (cold) valve body
(G) inlets.
Connect Shower Outlet Pipe to valve body (G). Plug bottom
outlet with plug (H). Connect Pipe Elbow (not included) to the
end of the pipe.
4. FOR SHOWER ARM INSTALLATION.
Insert the long end of the shower arm (B) through the flange (A)
then wrap plumber's tape to both sides of shower arm. Screw
long end of the shower arm into pipe elbow inside the wall.
5. FLUSHING
For Tub and Shower Combinations:
Turn on Hot and Cold water supply lines allowing water to flow
from tub spout outlet until all foreign matter has cleared the line.
For Shower Only Combinations:
Turn on Hot and Coldwater supply lines allowing water to flow
from shower outlet until all foreign matter has cleared the line.
Pressure must be approximately equal on both Hot and Cold
sides for valve to function properly.
3
30 inch
Tub&Shower
valve body
G
tub outlet pipe
Fig. 3
pipe elbow
shower
outlet pipe
valve body
G
bottom outlet
plug
Fig. 4
shower flange
shower arm
Fig. 5
H
A
pipe elbow
B
shower outlet
tub spout outlet
ASSEMBLY INSTRUCTIONS
6. FOR TUB SPOUT INSTALLATION
Install tub spout (I). Thread spout onto threaded connection
clockwise until the spout becomes flush with the finished wall.
Thread sealant may be required depending on your installation
method. All thread sealants may be found at your local
hardware store.
Fig. 6
tub spout
7. Before installing escutcheon (F), remove the plastic cap from
plaster guard by twisting cap in a clockwise direction.
8. Place handle on valve stem and turn handle to full on mixed
position. Turn on hot and cold water lines to full open for one
minute each. Check for leakage. Shut off water at faucet.
Remove the handle.
9. Install escutcheon (F) onto valve and then insert screws (E)
to attach to valve body (G). Install handle (D) and tighten
using allen wrench. Attach showerhead (C) to shower arm
(B).
ADJUSTING WATER TEMPERATURE
Turn on water so that cold water is as cold as it will get and hot
water is as hot as it will get. Remove the Rotational Limit Stop
from the valve by sliding it off the stem. Place handle back on
stem and rotate fully counterclockwise to the hottest position.
Place a thermometer in a plastic tumbler and hold in the water
stream. If the water temperature is above 120° F, the Rotational
Limit Stop must be rotated counterclockwise to decrease
temperature. Reinstall the stop by sliding it back on to the
stem before reinstalling the handle.
MAKE SURE COLD WATER FLOWS FROM THE VALVE
FIRST.
MAKE SURE WATER (AT THE HOTTEST FLOW) DOES NOT
EXCEED THE TEMPERATURE LIMIT ALLOWED BY YOUR
PLUMBING CODES (120° F OR 110° F).
4
I
Fig. 7
Fig. 8
Fig. 9
shower arm
showerhead
B
C
escutcheon
screw
handle
F
E
D
valve body
set screw
Fig. 10
colder
hotter
rotational limit stop
stop on cartridge
G
CARE AND MAINTENANCE
• Cleaning: Clean carefully by gently wiping with a grit-free damp cloth.
Use only mild soap with water.
Never use acids, harsh chemicals or abrasive detergents to clean surface.
TROUBLESHOOTING
Problem
Leaks underneath handle
Water will not shut off
completely
Possible Cause
Bonnet has become loose or
o-ring on cartridge is dirty or
twisted.
Rubber valve seat is dirty or
broken.
Corrective Action
Tighten the bonnet. Clean or
replace o-ring.
Remove handle and cartridge
to check the rubber valve
seat. Clean or replace it.
WARRANTY
LIFETIME LIMITED WARRANTY
This faucet has been manufactured under the highest standard of workmanship. All parts of this
faucet are warranted to be free from leaks or drips during domestic use for as long as the original
purchaser owns this product. THIS EXCLUDES INDUSTRIAL, COMMERCIAL, OR BUSINESS
USE. The manufacturer will replace FREE OF CHARGE, under the warranty conditions the entire
unit or any part (at our option) which proves defective in material and/or workmanship under
normal installation, use and service. This warranty is limited to defective parts as stated. All costs
of removal and installation of the faucet, including the replacement of warranty parts are the
responsibility of the purchaser. The manufacturer shall not be liable for incidental, consequential
or special damages arising at or in connection with product use or performance except as may
otherwise be accorded by law. This warranty gives you specific legal rights, and you may also
have other rights which may vary from state to state. Any damage to this faucet as a result of misuse,
abuse, neglect, accident, improper installation, or any use violating instructions furnished by us,
WILL VOID THIS WARRANTY. When requesting warranty service, you will need to present a copy
of your sales receipt as proof of purchase. To obtain warranty service, call our customer service
department at 1-866-417-7564.
5
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-866-417-7564,
8 a.m. - 8 p.m., EST, Monday - Friday.
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Description
Shower Flange
Shower Arm
Shower Head
Handle
Set Screw
Screw
Inverter
Screw
Escutcheon
Sleeve
O-ring
Cartridge
Plug
Tub Spout
Seal Seat
Seal Washer
Part #
RP38046*
RP38054*
RP38055*
RP13095*
RP50002
RP50070
RP64043
RP50066*
RP80191*
RP80032*
RP60018
RP20006
RP70153
RP33019*
RP70024
RP64133
A
B
C
L
J
K
I
M
H
F
D
G
E
N
* Available in Brushed Nickel Finish
Shower only faucet does not include Part N,
O, or P.
O
6
P