Assembly and Operating Instructions for Palermo

Assembly and Operating Instructions for
Palermo BBQ
SM-H5400
Photographs are not to scale.
Specifications subject to change
without prior notice.
•
•
•
•
•
•
WARNING
•
•
•
•
0359
For outdoor use only. Not for commercial use.
Read instructions before using the appliance. Failure to follow instructions could
result in death, serious bodily injury, and/or property loss.
Warning: accessible parts may be very hot. Keep young children and pets away.
Do not move the appliance during use.
Turn off the gas supply at the gas bottle after use.
Any modification of the appliance, misuse, or failure to follow the instructions may
be dangerous and will invalidate your warranty. This does not affect your statutory
rights.
Retain these instructions for future reference.
Leak test annually, and whenever the gas bottle is removed or replaced. Check that
the hose connections are tight and leak test each time you reconnect the gas bottle.
For Flare-up control please refer to the ‘OPERATION’ section of this manual.
THIS BBQ MUST NEVER BE LEFT UNATTENDED WHEN LIT AND IN USE.
FOR YOUR SAFETY
If you smell gas:
1.
Shut off gas to the appliance.
2.
Extinguish any open flame.
3.
Open barbecue lid or hood.
4.
If odour continues, discontinue use and
contact your local dealer.
FOR YOUR SAFETY
1.
2.
Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
A gas bottle not connected for use must not be
stored in the vicinity of this or any other
appliance.
1. Parts List
Quantity varies according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see the corresponding ‘Hardware Reference Diagram’.
CODE
HOOD
BODY
TROLLEY
HARDWARE
PART
QTY
A1
Hood (Pre-Assembled to Body)
1
A2
Hood Handle
1
A3
Warming Rack
1
B1
Barbecue Body
1
B2
Burner
4
B3
Control Panel
1
B4
Knob
4
B5
Hose/Regulator Assembly
1
B6
Flame Tamer
2
B7
Cooking Grill
1
B8
Cooking Plate
1
B9
Ignition Pushbutton
1
B10
Drip Tray Left Bracket
1
B11
Drip Tray Right Bracket
1
B12
Drip Tray
1
B13
Cylinder Hook
1
C1
Side Shelf
2
C2
Left Front Leg
1
C3
Left Rear Leg
1
C4
Right Front Leg
1
C5
Right Rear Leg
1
C6
Screen
1
C7
Leg Support
1
C8
Cylinder Retainer
1
C9
Wheel
2
C10
Axle
1
C11
Wire Base
1
D1
ST4.0x10 Screw
4
D2
M5x10 Bolt
2
D3
M5 Nut
2
D4
M6x15 Bolt
8
D5
M6x40 Bolt
12
D6
Ø6 Washer
4
D7
M6 Nut
4
D8
Locknut
2
Pre-Assembled Component
2
4 Burner Hooded BBQ
2. Parts Diagram
Quantity varies according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see the corresponding ‘Hardware Reference Diagram’.
B8
B7
A3
B6
A2
A1
B1
B2
B13
B3
B9
B4
B11
B10
B5
C2
C1
C3
B12
C6
C8
C7
D8
C10
C11
C9
3
C4
C5
3. Hardware Reference Diagram
Specifications subject to change without prior notice.
Code Description
D1
D2
D3
Illustration
Amount
ST4.0x10
Screw
4
M5x10
Bolt
2
Code Description
D5
D6
M5 Nut
M6x15
Bolt
Amount
12
Ø6 Washer
4
D7
2
D4
M6x40
Bolt
Illustration
M6 Nut
4
D8
8
Locknut
2
4
4. Assembly
IMPORTANT!
• TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver,
adjustable spanner or metric spanner set.
• The assembly of this barbecue requires 2 people.
• Whilst every care is taken in the manufacture of this product, care must be taken during assembly in
case sharp edges are present.
• Please read the Important Information section carefully before assembly and use of your
barbecue.
1
C2
C3
C5
C4
C11
Attach the Legs (C2,C3,C4,C5) to the Wire Base (C11) by inserting the M6x40 Bolts (D5)
through the legs, wire base, Ø6 Washers (D6) and secure with M6 Nuts (D7). Make sure that
the two guide holes on the top of each leg should be located at the front looking from the
side. Ensure that the legs with the Velcro attached to them are at the front of the barbecue,
facing inwards.
2
C9
C3
C10
C2
C4
C5
D8
Turn the trolley over, upside down. Unscrew the Locknuts (D8) from both ends of the Axle
(C10). Slide the axle through the corresponding holes in the left legs. Slide the Wheels (C9)
over each end of the axle. Secure the wheels into place with the locknuts.
5
3
B1
D5
Remove all loose components from the Barbecue Body (B1). Carefully lay the barbecue body
on its back and also lay the assembled trolley on its back. CAUTION! Care must be taken to
ensure the hood or lid does not fall open unexpectedly or becomes damaged when it is
set on the ground. We recommend flattening the BBQ carton to lay the BBQ down on, to
avoid scratching any components. Insert the M6x40 Bolts (D5) through the guide holes of each
leg and screw into barbecue body tightly.
Stand the barbecue upright, make sure the holes in both front and rear legs to fix the body are
located towards front of the barbecue as shown.
4
C1
C1
D4
Attach the Side Shelves (C1) to the barbecue body using the M6x15 Bolts (D4).
6
5
B7
B8
B6
Carefully lay the Flame Tamers (B6) into the barbecue body ensuring it lies level within the
body. Lay the Grill (B7) and Plate (B8) into place. Ensure the cooking grill lies directly over the
flame tamer on the LEFT side of the barbecue body.
6
D1
C7
Install the Leg Support (C7) onto left legs using ST4.0x10 Screws (D1).
7
7
B12
B11
The Drip Tray Brackets (B10, B11) are fixed tightly to the side panel of barbecue body with drip
tray bracket bolts and slid up tightly against the grill body for shipping. Untighten the bolts to slide
the brackets down and remove the Drip Tray (B12). Retighten the bolts, reverse drip tray and
slide it back into position underneath the barbecue body.
8
D3
C8
D2
Attach the Cylinder Retainer (C8) onto leg support by inserting the M5x10 Bolts (D2) through the
retainer, leg support and secure with M5 Nuts (D3).
8
9
A1
A3
B1
Attach the Warming Rack (A3) to the Hood (A1) and Barbecue Body (B1) as shown.
Make sure that the swing legs fix to the body of the barbecue and the shorter fixed
legs go through the holes in the hood.
10
B13
C6
Insert the Cylinder Hook (B13) into the hole provided in the left side of the barbecue
body. Attach the Screen (C6) onto front legs with Velcro as shown.
9
11
B5
Connect the Hose and Regulator Assembly (B5) to the barbecue.
Ensure the mating faces of the connection are clean and not damaged. Do not use
any sealing tape, paste, or liquid on the connection. The nut must be tightened with
the use of a spanner. Do not use force which may damage the assembly.
ASSEMBLY IS NOW COMPLETE.
PROCEED TO THE NEXT PAGE FOR INSTRUCTIONS ON OPERATION AND
MAINTENANCE
ALL JOINTS AND CONNECTIONS MUST NOW BE LEAK TESTED BEFORE USING THE
BARBECUE.
Leak test annually, and whenever the gas bottle is removed or replaced.
Leak Testing
Always perform a leak test in a well-ventilated area.
Step 1 - Confirm all control knobs are in the off position.
Step 2 - Turn the gas on / open the gas control valve on the gas bottle slowly and smoothly.
Step 3 - Check for leaks by brushing a solution of ½ water and ½ liquid detergent / soap over all
the gas system joints, including gas bottle valve connections, hose connections, and regulator
connections.
Step 4 - NEVER USE AN OPEN FLAME to test for leaks at any time.
Step 5 - If bubbles form over any of the joints there is a leak
• Turn off the gas supply at the gas bottle
• Retighten all joints
• Repeat test
• If bubbles form again do not use the barbecue and contact your local distributor for assistance.
Always wipe the mixed solution (½ water and ½ liquid detergent / soap) from all joints and
connections after leak testing.
10
to detect any gas leaking from joints and
connections of the barbecue after assembly.
n
Leak test annually, and whenever the gas
bottle is removed or replaced.
n
Do not store flammable materials near this
barbecue.
n
Do not use aerosols near this barbecue.
n
Failure to follow the manual’s instructions
could result in serious injury or damage.
n
Modification of the barbecue may be
dangerous, is not permitted and will nullify
any warranty.
n
If you have any queries regarding these
instructions, contact your local dealer.
5. Important Information
Please read these instructions carefully
before assembly and use of your barbecue.
n
Retain these instructions for future reference.
n
This product is for outdoors use only. Do not
use indoors.
n
Do not use the barbecue or store gas bottles
below ground level. LP gas is heavier than
air so if a leak occurs the gas will collect at a
low level and could ignite in the presence of
a flame or spark.
n
For use with LPG bottled gas only. A suitable
regulator must be used for LP gas.
n
Remove plastic wrap from any part before
lighting.
n
Do not use within 1m of any flammable
structure or surface. Do not use under any
combustible surface.
n
LP gas bottles should never be placed
directly underneath the barbecue.
n
LP gas bottles should never be stored or
used laid on their side, in the horizontal
position. A leak would be very serious and
liquid could enter the gas line with serious
result.
n
Never store gas bottles indoors.
n
Open the barbecue hood or lid before
lighting.
n
Once lit, do not move the barbecue until it
has completely cooled, after use.
n
THIS BBQ MUST NEVER BE LEFT
UNATTENDED WHEN LIT AND IN USE.
n
The hood or lid handle can become very hot.
Grip only the centre of the handle. Always
use oven gloves when cooking or carrying
out any adjustments to the barbecue.
n
Use purpose designed barbecue tools with
long, heat resistant handles.
n
Use caution when opening the hood (where
applicable), as hot steam inside is released
upon opening.
n
Parts of this barbecue become very hot –
care must be taken, especially when
children, elderly people, and animals are
present.
n
Turn off the gas supply at the gas bottle after
use.
n
Never cover a barbecue until it has
completely cooled.
n
Use this barbecue only on a stable, flat
surface.
n
Before you use your barbecue, perform a
leak test. This is the only safe and sure way
6. Gas, Regulator and Hose
This barbecue can use mixed LPG (liquid
petroleum gas) bottled gas only. Check that you
have the correct gas bottle to match the
regulator supplied with your barbecue.
Do not stand the bottle on the wire base.
•
•
•
The hose should hang freely with no bends,
twisting, tension, folds, or kinks that could
obstruct free flow of gas. Always inspect the
hose for cuts, cracks, or excessive wear
before use.
Apart from the connection point, no part of
the hose should touch any hot barbecue
parts. If the hose shows any sign of damage
it must be replaced with a hose suitable for
use with LP gas which meets the national
standards for the country of use.
The length of hose should not exceed 1.5
metres.
For optimal performance, we suggest to use a
9kg LP gas bottle. This appliance is supplied
with a 2.75kPa LP gas regulator of an approved
type. YOU MUST HAVE THE PROPER
REGULATOR AND BOTTLE IN ORDER FOR
THE BARBECUE TO OPERATE SAFELY AND
EFFICIENTLY. USE OF AN INCORRECT OR
FAULTY REGULATOR IS DANGEROUS AND
WILL INVALIDATE ANY WARRANTY. Please
consult your local gas dealer for the most
suitable gas bottles and regulators.
7. Installation
7.1. Selecting a Location
This barbecue is for outdoor use only and
should be placed in a well-ventilated area,
11
and on a safe and even surface. Never place
your barbecue below ground level. Take care to
ensure that it is not placed UNDER any
combustible surface. The sides of the barbecue
should NEVER be closer than 1 metre from any
combustible surface, including trees and fences
and make sure that there are no heat sources
near the barbecue (cigarettes, open flames,
spark etc.). Keep this barbecue away from any
flammable materials!
2, Next open the gas cylinder valve ,
opening the first half turn slowly before,
then opening the gas tap fully .
n
Your barbecue is not designed to be used
with more than 50% of the cooking area as
a solid plate — this includes baking dishes.
Full coverage will cause excessive build-up
of heat and damage the barbecue. This is
not covered by warranty.
n
WARNING: This BBQ must never be
left unattended when it is lit and in use.
7.2. Precautions
Do not obstruct any ventilation openings in the
barbecue body.
8.2. Preparation Before Cooking
To prevent foods from sticking to the cooking
surface, please use a long handled brush to
apply a light coat of cooking or vegetable oil
before each barbecuing session. (Note:
When cooking for the first time, paint colours
may change slightly as a result. This is normal
and should be expected.) During use, the
protective coating may come off the cooking
surface. This is normal and is not harmful.
Mount cylinder onto cylinder hook by slipping
the cylinder hook through the cylinder collar
and secure cylinder bottom ring with cylinder
retainer on the leg support.
Should you need to install or change the gas
bottle, confirm that the barbecue is switched
off, and that there are no sources of ignition
(cigarettes, open flame, sparks, etc.) near
before proceeding.
Line the drip tray with aluminium foil, then place
a uniform layer of clean, dry sand, or even
better an absorbent material like kitty litter 1cm
deep into the tray. This will absorb excess
cooking fat, thus making cleanup easy.
7.3. Connecting a Gas Hose to the Barbecue
Connect the gas hose to the gas rail inlet on
the left hand side of the barbecue. Do not
overtighten. Do not use any sealing tape, paste
or liquid on the connection.
8.3. Lighting the Barbecue
• Remove the lid or open the hood before
lighting. Never light your barbecue with the
hood or lid closed.
• Always ensure all BBQ control knobs
are in the off position before opening
the gas control valve on the gas bottle
slowly and smoothly.
• Push and turn the control knob of the
leftmost burner to the high position. Press
the ignition button rapidly several times until
burner is lit.
• If burner fails to ignite after following above
procedure, turn all the knobs to the off
position. Close the gas valve on the gas
bottle. Wait 5 minutes. Reattempt all of the
above steps. If the barbecue still fails to
light, please refer to the manual ignition
instructions below.
• After successful lighting of the leftmost
burner, ignite the remaining burners in
sequence from left to right. Confirm each
burner is alight before igniting another
burner.
• After ignition, turn the burners to the high
position for 3-5 minutes in order to pre-heat
the barbecue. This should be done before
7.4. Fixing a Regulator to the Gas Bottle
Confirm all barbecue control knobs are in the
off position. Connect the regulator to the gas
bottle according to your regulator and bottle
dealer’s instructions.
8. Operation
8.1. nWarnings
n
Before proceeding, make certain that you
understand
the
IMPORTANT
INFORMATION section of this manual.
nThe regulator supplied with this BBQ
is equipped with a safety mechanism
called an Excess flow valve. To avoid
tripping this device, which will prevent
full gas requirement reaching the BBQ,
it is vital that following actions are
taken prior to igniting the BBQ ;
1, Prior to opening the gas cylinder
valve, make sure all BBQ control
valves are in the “off” position.
12
•
each cooking session. The hood or lid
should be open during preheating.
After completion of preheating, turn all
burners to the low position for best cooking
results.
kitchen, for searing steaks, cooking eggs, etc.
Alternatively, it can be used for heating pans or
keeping food warm.
8.7. Roasting Hood Cooking
Barbecues equipped with a roasting hood give
the option to form an ‘oven’ for roasting or
baking food, such as joints of meat or whole
chickens, etc. More even cooking of food will
actually be achieved by using the barbecue
with the hood down. However, this should
only be done with the burners on low.
8.4. Manual Ignition Instructions
• Remove the lid or open the hood before
lighting. Never light your barbecue with the
hood or lid closed.
• Always ensure all BBQ control knobs
are in the off position before opening
the gas control valve on the gas
bottle slowly and smoothly.
• Insert lit match through the right matchlighting hole on the right side of the
barbecue body and place near rightmost
burner porthole.
• Push and turn the rightmost control knob
anti-clockwise to the high position, taking
care to protect yourself from the flames.
• When the right burner is lit, turn the
remaining burners on from right to left.
• Confirm that each burner is alight before
turning on the next burner.
• If a burner fails to ignite, contact your local
dealer for assistance.
• After ignition, turn the burners to the high
position for 3-5 minutes in order to pre-heat
the barbecue. This should be done before
each cooking session. The hood or lid
should be open during preheating.
• After completion of preheating, turn all
burners to the low position for best cooking
results.
For best results, place the food you wish to
bake or roast on a metal baking tray and set it
on one side of the cooking grill.
Turn the burner directly under the food to the
OFF position and turn all other burners to a
LOW to MEDIUM position.
Close the hood to cook the food ‘indirectly’.
Avoid lifting the hood unnecessarily as heat is
lost every time the hood is opened. If the hood
is opened during cooking please allow extra
time for the barbecue to regain its temperature
and complete the cooking.
If the internal heat becomes too high, turn the
burners down to the low position. It is not
necessary or advisable to have all of the
burners on high when the hood is closed. This
would create an overheating risk.
DO NOT ALLOW YOUR BARBECUE TO
OVERHEAT. Take care when opening the
hood as hot steam can be released on opening.
8.5. Grill Cooking
The burners heat up the flame tamers
underneath the grill, which in turn heats the
food on the grill. The natural food juices
produced during cooking fall onto the hot flame
tamers below and vaporise. The subsequent
rising smoke bastes the food, as it travels
upwards, imparting that unique barbecued
flavour.
8.8. Warming Rack
Warming racks are a convenient way to keep
cooked food warm or to warm items such as
bread rolls. It is advisable to place food
(particularly fatty foods) to the front of the
warming rack to avoid the possibility of juices
and fat running down the back of your
barbecue. Always check that your warming
rack is properly fitted before use.
8.6. Griddle Plate Cooking
The burners heat the griddle plate directly,
which then cooks the food on contact. Griddle
plates allow for the cooking of smaller items,
such as seafood, which could fall through the
spaces of a grill. They are also suitable for
cooking items that require high-temperature/
short-duration cooking, such as vegetables and
smaller cuts of fish. Similarly, it can be used in
exactly the same way as a griddle in the
8.9.Flare-Up Control * VERY IMPORTANT *
Flare-ups occur when meat is barbecued, and
its fat and juices fall upon the hot flame tamer.
Smoke of course helps give food its barbecued
flavour, but it is best to avoid excessive flare-up
to prevent food being burned. To control flareups, it is ABSOLUTELY ESSENTIAL to trim
away excess fat from meat and poultry before
grilling, use cooking sauces and marinades
13
turn all the control valves fully clockwise to
the “Off” position, then switch off the gas
supply at the bottle.
sparingly and try to avoid very cheap cuts of
meat or meat products as these tend to have a
high fat and water content. Also, the burners
should always be placed on the low setting
during cooking.
Wait until the barbecue is sufficiently cool
before closing its hood or lid.
When flare-ups do occur, they can usually be
extinguished by applying baking soda or salt
directly onto the flame tamer. Always protect
your hands when handling anything near the
cooking surface of the barbecue and take care
to protect yourself from the flames.
9. Care and Maintenance
Regularly clean your barbecue between uses
and especially after extended periods of
storage. Ensure the barbecue and its
components are sufficiently cool before
cleaning. Do not leave the barbecue exposed
to outside weather conditions or stored in
damp, moist areas.
If a fat fire occurs, please see the instructions
given below.
8.10. Fat Fires
Empty and clean the drip tray (and foil liner, if
applicable) of food debris after each cooking
session. If the barbecue is to be used for large
gatherings, it will be necessary to turn off and
cool the barbecue every two hours to remove
food debris from the drip tray (and foil liner, if
applicable) and clean it out. The time between
cleaning may need to be reduced if very fatty
foods or cheap meat products are being
cooked. Failure to do this may result in a fat
fire, which may cause injury and could seriously
damage the barbecue.
n
Never handle hot parts with unprotected
hands.
n
Never douse the barbecue with water when
its surfaces are hot.
In order to extend the life and maintain the
condition of your barbecue, we strongly
recommend that the unit be covered when left
outside for any length of time, especially during
the winter months.
Even when your barbecue is covered for its
protection, it must be inspected on a regular
basis as damp or condensation can form which
may result in damage to the barbecue. It may
be necessary to dry the barbecue and the
inside of the cover. It is possible for mould to
grow on any fat remaining on parts of the
barbecue. This should be cleaned off smooth
surfaces with hot soapy water.
In the event of a fat fire:
• If safe to do so, turn all control knobs to the
‘off’ position.
• Turn off the gas supply at the gas bottle.
• Keep everyone at a safe distance from the
barbecue and wait until the fire has burnt
out.
• Do not close the hood or lid of the
barbecue.
• NEVER DOUSE A BARBECUE WITH
WATER. IF AN EXTINGUISHER IS USED,
IT SHOULD BE A POWDER TYPE.
• DO NOT REMOVE THE DRIP TRAY.
• If the fire does not seem to be abating or
appears to be worsening, contact your local
Fire Brigade for assistance.
Any rust that is found that does not come into
contact with the food should be treated with a
rust inhibitor and painted with barbecue paint or
a heat resistant paint.
A chrome cleaner may be used on chrome
parts if required. To prevent rusting, wipe
chrome plated warming racks etc. with cooking
oil after rinsing and drying.
8.11. End of Cooking Session
After each cooking session, turn the barbecue
burners to the “high” position and burn for 5
minutes. This procedure will burn off cooking
residue, thus making cleaning easier. Make
sure the hood or lid is open during this process.
9.1. Cooking Surfaces & Warming Rack
When the barbecue has cooled, clean with hot
soapy water. To remove any food residue, use
a mild cream cleaner on a non-abrasive pad.
Do not use scouring pads or powders as they
can permanently damage the finish. Rinse well
and dry thoroughly. To protect the cast iron
8.12. Turning Off Your Barbecue
When you have finished using your barbecue,
14
cooking surfaces, after clean and dry apply a
light coat of cooking oil to the cooking surfaces.
Due to the weight of the cooking surfaces, we
do not recommend cleaning in a dishwasher.
It is quite normal for surface rust to be present
on the cooking surface. If rust appears between
uses or in storage, clean with a soft brass wire
brush. Be careful not to damage the cooking
surface, re-oil and cure.
body using a soft plastic or wooden scraper. It
is not necessary to remove all the grease from
the body. If you need to clean fully, use hot
soapy water and a cloth, or nylon-bristled brush
only. Do not use abrasives. Remove cooking
surfaces and burners before full cleaning. Do
not immerse the gas controls or manifold in
water. Check burner operation after carefully
refitting into body.
9.2. Burner
Provided that they are operating correctly, in
normal usage, burning off the residue after
cooking will keep the burners clean.
9.6. Barbecue Hood & Trolley
Use a non-abrasive cloth or pad and clean with
hot, soapy water. Do not use scouring pads or
powders as they can permanently damage the
finish.
The burners should be removed and cleaned
annually, or whenever heavy build-up is found,
to ensure that there are no signs of blockage
(debris, insects) in either the burner portholes
or the primary air inlet of the burners. Use a
pipe cleaner to clear obstructions.
9.7. Fixings
All screws and bolts, etc. should be checked
and tightened on a regular basis.
9.8. Storage
Ensure the barbecue is properly cooled before
covering or storing. Store your barbecue in a
cool dry place.
When refitting the burners, be careful to check
that the neck of the burner fits over the valve
outlet.
Cover the burners with aluminium foil in order
to prevent insects or other debris from
collecting in burner holes.
It is quite normal for surface rust to be present
on the burners. If rust appears between uses or
in storage, clean with a soft brass wire brush.
If the barbecue is to be stored indoors, the gas
bottle must be disconnected and left outside.
The gas bottle should always be stored outside,
in a dry, well-ventilated area, away from any
sources of heat or ignition. Do not let children
tamper with the bottle.
9.3. Flame Tamer
Remove any food residue from the flame tamer
surface with a plastic or wooden scraper or
brass wire brush. Do not use a steel scraper or
wire brush. Clean with hot soapy water and
rinse well.
When using the barbecue after extended
periods of storage follow the cleaning
procedures.
9.4. Drip Tray
After every use, empty and clean the drip tray
(and foil liner, if applicable) of any fat or food
particles, using a plastic or wooden scraper if
necessary.
Failure to keep it clean, and excessive build up
can result in a fat fire. This can be hazardous
and severely damage the barbecue. This is
not a fault in the barbecue and is therefore
not covered by the terms of the warranty. If
required, the tray can be washed in hot soapy
water.
9.5. Barbecue Body
Regularly remove excess grease or fat from the
barbecue body using a cloth wrung out in hot
soapy water and dry thoroughly. Excess fat and
food debris can be removed from inside the
10. Technical Specifications
Necessities
Outdoor
Palermo
CE
Approval
Total
Heat
Input
Burners
Injector
Size
Operating
Pressure
0359
359CM1174
17.28
Kw
4
1.02mm
2.75kPa
SM-H5400
Gas Consumption: 1258g/hr
Min.Gas Supply Pressure:2.05kPa; Max.Gas Supply Pressure:3.45kPa
Specifications subject to change without prior notice.
15
11. Troubleshooting
Problem
Possible Cause
Solution
Burner will not light using
the ignition system
LP gas bottle is empty
Replace with full bottle
Faulty regulator
Have regulator checked or replaced
Obstructions in burner
Clean burner
Obstructions in gas jets or gas
hose
Clean jets and gas hose
Electrode or ignition button wire is
loose or disconnected on electrode or
ignition unit
Reconnect wire
Electrode or wire is damaged
Change electrode and wire
Faulty integral ignitor
Change ignitor
Incorrect electrode gap/ Bent collector The gas collector box around the
box
electrode needs to be in line with the
burner with a gap of 3 to 4mm between
the end of the electrode and the tag on
the end of the collector box. Realign
the collector box as required.
Burner will not light with a
match
Low flame or flashback
(fire in burner tube— a
hissing or roaring noise
may be heard)
Gas valve knob difficult to
turn
LP gas bottle is empty
Replace with full bottle
Faulty regulator
Have regulator checked or replaced
Obstructions in burner
Clean burner
Obstructions in gas jets or gas
hose
Clean jets and gas hose
Excess Flow Valve has been
tripped
Follow instructions in separate
document “important information
regarding correct BBQ lgnition
procedure”
LP gas bottle too small
Use larger bottle
Obstructions in burner
Clean burner
Obstructions in gas jets or gas
hose
Clean jets and gas hose
Windy conditions
Use barbecue in a more sheltered
position
Integral ignition system jammed
Replace gas valve
Gas valve jammed
Replace gas valve
For reference and correspondence, record your serial number here.
(See sticker on side of barbecue body.)
Serial No.__________________
This number may be required when ordering spare parts or accessories.
A part reference number may also be required where applicable.
16