Product Specification Minimum Pressure Maximum Pressure 1.5 bar 3.0 bar Cold Temperature 4 - 20 c Hot temperature 55 - 85 c 1/2" bsp female end flexi-connectors Single function rub clean hand shower Single function rub clean shower head Single function rub clean body jets 38c Temperature stop position Minimum 10c difference between hot supply and mixed outlet temperature In-coming pressures should be balanced Aspire Shower Panel 9006 -- 9007 Important When drilling check wires and pipes will not be damaged Before installation fully flush the system to remove debris Hot supply must be on left and cold supply on right Cleaning All surfaces should be cleaned using a clean damp cloth. No abrasive cleaning agents or materials should be used. Telephone 0844 484 7678 BB INST 9006 - ISSUE 1 Please retain this manual after installation for future reference and maintenance. Product must be installed in compliance with relevant Water Regulations and Byelaws Page 1 Dimensions Page 6 Operation Installation Once all of the pipe connections have been made and checked for leaks. Hook the panel over the wall mounting brackets. Align so that the panel hangs vertically. The panel can be sealed down each edge if required. BB INST 9006 - ISSUE 1 Installation Page 5 Parts Page 2 Place outlet thread through side of panel and connect nut. Ensure washer is fitted in elbow and connect to thread Connect red and blue flexi-tails to hot and cold supply Tighten all connections BB INST 9006 - ISSUE 1 Part 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Code P0026-2 P0026-3 P0028-2 P0008-8 P0008-9 P0008-10 P0008-11 P0045-6 P0022-1 P0021-4 P0048-1 P0023-1 P0005-5 P0007-4 P0049-1 Description Overhead shower - Steel Overhead shower - Black Mounting brackets Overhead control handle Body jet control handle Hand shower control handle Temperature control handle Temperature dial Hose seals Hand shower Outlet elbow Shower hose Thermostatic cartridge Flow control valve Supply flexi-tails Installation Page 3 Page 4 Installation Place the shower head onto the main panel and align the holes. Fit the bolts through the four holes and connect the nuts from inside the main panel, tighten fully. Prepare holes in the wall to secure the mounting brackets. Ensure the bracket positions are vertically aligned. The hole centres are 25mm apart in Feed the long flexi-pipe through the width and 1290mm apart in height. larger hole in the centre of the panel. The bottom holes should be approx Pull this towards the outlet inside the 125mm from the bottom of the panel. head of the panel. Drill the holes and insert plugs, tap in Fit the jubilee clip to the flexi-pipe. the plugs to make them flush with the finished wall. Connect end of pipe to the outlet once fully attached, tighten clip. Offer the mounting plate to the wall and secure using the screws provided. BB INST 9006 - ISSUE 1 Guarantee Your product comes with a 1 year guarantee when installed, used and cleaned in accordance with this manual. Your product comes with a 1 year guarantee when installed, used and cleaned in accordance with this manual. Not covered by the guarantee is: Not covered by the guarantee is: • Breakdown due to a) Use other than domestic b) Wilful act of neglect c) Any malfunction resulting from incorrect use d) Incorrect setting of controls e) Any malfunction resulting from poor water quality • Repair costs for damage caused by foreign objects or substances • The cost of repair or replacement of pressure relief devices, spray heads, hoses, riser rails and/or wall bracket or any other accessories installed at the same time. • The cost of routine maintenance, adjustments, overhaul, modifications, loss or damage, arising therefrom, • Total loss of the product due to non-availability of parts including the cost of repairing damage, breakdown, malfunction caused by corrosion, furring, pipe scaling, lime scale, • Compensation for loss of use of the product or consequential loss of any kind. • Call out charges where no fault has been found with the product. BB INST 9006 - ISSUE 1 system debris or frost.