FAUCET SPECIFICATIONS Pull-Down Spray Kitchen Faucet Model

FAUCET SPECIFICATIONS
Pull-Down Spray Kitchen Faucet
Model VG02001
MODEL VG02001
FEATURES
PACKING LIST
DIMENSIONS
MODEL #
18 1/2" *
VG02001
HOLE
DIAMETER
1 3/8"
FAUCET
HEIGHT
18 1/2"
SPRAYER
REACH
9 1/2"
9 1/2"
1 3/8"
NOTE: All faucets are compliant to CEC 2016 regulations. If you
have inquiries about your water flow, please email
techmail@vigoindustries.com.
* = +/- 1"
9 1/2"
18 1/2"
EXPANDABLE
UP TO 30"
6 1/4"
2"
2 1/4"
4 1/2"
5 5/8"
10 3/8"
FUNCTION
BUTTON
1 3/4"
2 1/4"
SIDE VIEW
SPRAY HOSE
TOP VIEW
FRONT VIEW
VG02001
THE MEASUREMENTS IN INCHES ARE ROUNDED TO THE NEAREST 1/8"
2
FLOW RATE REGULATIONS
This product meets the CEC requirements. It is up to the discretion of the client to modify the product with the
provided restrictor. Doing so will remove the ability for the product to meet certain low flow standards. Please talk to
your local or statewide plumbing enforcement agency prior to modifying. Vigo is not responsible for any alterations
and the affects that may come with altering the product post sale and highly advises that the client only install the
product that meets the needs of their local plumbing code.
Flow rate with restrictor - 1.8 gpm
Flow rate without restrictor - 2.2 gpm
Twist the sprayer counterclockwise to remove the sprayer
from the hose. You will find the flow restrictor in here.
Simply remove the 1.8 gpm flow restrictor and replace it with
the 2.2 gpm flow restrictor (provided). Replace the sprayer
by twisting it back on to the hose.
Note:
You will need tools to remove the flow restrictor. Use
precautionary measures in order to not cause bodily harm.
Flow restrictor
Using a tool, remove the flow restrictor
by getting a good grip on it and pulling
up. It may take some time, the flow
restrictor is tightly secured.
1.8gpm Flow restrictor
Sprayer
2.2gpm Flow restrictor
Sprayer
3
PACKAGE CONTENTS
ASSEMBLY
RUBBER RING
COUNTERWEIGHT
1. SHUT OFF WATER SUPPLY. REMOVE THE OLD FAUCET
AND FLEXIBLE HOSES. CLEAN SINK SURFACE WITH A NON
ABRASIVE CLEANER IN PREPARATION FOR THE NEW FAUCET.
1
METAL RING
PLASTIC HOLDER
NUT
2
2. THREAD FEMALE END OF METAL BRAIDED HOSE TO THE
FAUCET (2).
HOLLOW PIN
!
COPPER PIN
SPRAYER
FAUCET
ASSEMBLY
TWO METAL
BRAIDED HOSES
ENSURE THAT YOU USE PIPE TAPE
AND DO NOT OVER TIGHTEN THE
SUPPLY LINE NUTS AS THIS COULD
CAUSE PRODUCT FAILURE LEADING
TO WATER DAMAGE.
ALLEN KEY (REMOVES HANDLE
TO ACCESS CARTRIDGE)
REQUIRED TOOLS
Adjustable wrench
Allen key - supplied (to remove cartridge if needed)
Plumber's putty - optional
Pipe tape
Flat screwdrivers
3. POSITION THE FAUCET IN THE COUNTERTOP HOLE, FROM
BENEATH THE COUNTERTOP HOLE ASSEMBLE THE PLASTIC
HOLDER, RUBBER RING, AND METAL RING IN THE ORDER
DEPICTED IN THE DIAGRAM. THEN THREAD METAL NUT ONTO
HOLLOW PIN. TIGHTEN THE METAL NUT UNTIL FAUCET IS
SECURE.
3
SAFETY TIPS
If you use soldering for the installation of the faucet, the seats, cartridges and
washers will have to be removed before using flame. Damage caused by
improper soldering will void the warranty.
Protect your eyes with safety glasses when cutting or soldering water supply
lines.
!
ENSURE THAT PARTS ARE
ASSEMBLED IN THE ORDER AS
DEPICTED IN DIAGRAM TO PREVENT
DAMAGE TO FAUCET AND SUPPLY
LINES.
IMPORTANT POINTS
Prior to beginning installation, turn off the cold and hot water lines and open the
hot and cold knobs on the old faucet to release pressure.
When installing your new faucet, turn the connector nuts finger-tight, then use
one wrench to anchor the fitting and a second wrench to tighten the nut.
Connections that are too tight will reduce the integrity of the system and
potentially cause product failure which could lead to water damage.
Wrap all threaded connections with pipe tape available at your local hardware or
plumbing supply store. Always wrap in a clockwise direction.
Not all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.
Prior to installing the faucet please FLUSH THE HOT AND COLD WATER
SUPPLY LINES that are or will be connected to the new faucet to remove scale,
solder or their impurities which could damage the faucet and potentially void the
warranty.
STABILIZES FAUCET
UNDER COUNTERTOP
NUT
4. SCREW SPRAY HOSE TO THE COPPER PIN (THE LONGEST
PIN). MAKE SURE TO HAVE A TIGHT SEAL USING ADJUSTABLE
WRENCH. ATTACH SUPPLIED COUNTERWEIGHT TO THE HOSE.
!
5. (IF NOT DONE ALREADY) ATTACH SPRAYER TO FEMALE
CONNECTION OF SPRAYER HOSE BY HAND AND TIGHTEN
UNTIL SECURE. MAKE SURE THE BLACK WASHER WITH
SCREEN IS SEATED AND INSTALLED PROPERLY.
!
MAINTENANCE
Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals as these will scratch, dull, and/or
damage the finish and void the warranty.
INSTALLATION
Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact the Vigo Technical Support
Department before proceeding with installation.
DO NOT OVER TIGHTEN CONNECT
POINT AS THIS COULD CAUSE
PRODUCT FAILURE LEADING TO
WATER DAMAGE
4
USE WASHER WITH SCREEN AT CONNECTION POINT BETWEEN SPRAYER
AND SPRAYER HOSE. THIS WILL STOP DEBRIS FROM TRAVELING INTO THE
SPRAYER HEAD AND EFFECTING ITS FUNCTIONALITY. PLEASE NOTE THAT
THE SCREEN WASHER WILL NEED TO BE REMOVED AND CLEANED
APPROXIMATELY ONCE EVERY 3 MONTHS TO AVOID BUILD UP AND LOW
WATER FLOW.
6. ATTACH THE FEMALE CONNECTIONS OF THE FLEXIBLE HOSES TO
THE COLD AND HOT WATER SUPPLY .
!
ENSURE THAT YOU USE PIPE TAPE
AND ADJUSTABLE WRENCH, DO NOT
OVER TIGHTEN AS THIS COULD
CAUSE PRODUCT FAILURE LEADING
TO WATER DAMAGE.
7. AFTER INSTALLATION IS COMPLETE, TURN ON THE WATER
SUPPLY AND ALLOW BOTH HOT AND COLD WATER TO RUN
SEPARATELY FOR AT LEAST TWO MINUTE EACH. WHILE
WATER IS RUNNING, CHECK FOR LEAKS. IT IS IMPORTANT TO
VIEW THE CONNECTIONS AT THE MALE AND FEMALE FLEXIBLE
HOSE CONNECTIONS. IF LEAKS ARE DETECTED, REFER BACK
TO THE INSTRUCTIONS AND ADJUST ACCORDINGLY.
TIGHTENING NUTS SLIGHTLY MAY STOP ANY MINOR LEAKS.
6
4
TROUBLESHOOTING
PROBLEM
POTENTIAL CAUSE
1 - Leaks from handle
2 - Insufficient flow rate
3 - Leak at connection points
4 - Loose faucet body
5 - Sprayer button stops working
CORRECTIVE ACTION
1.A - Cartridge unseated
1.B - Cartridge defective
1.A - Remove cartridge from housing, wash thoroughly with hot
water and reseat in housing.
2.A - Dirty aerator
2.B - Clog in supply hose / line
1.B - Contact Vigo Technical Support for replacement.
3.A - Sprayer hose not tight
3.B - Flexible hose leaking at body or connection point
2.A - Remove and soak / clean with a non abrasive agent (i.e.
vinegar).
2.B - Remove sprayer or supply line and flush lines
3.A - Remove sprayer and check integrity of the black washer.
Make sure the washer is seated properly and retighten.
3.B - Tighten hoses. If this does not resolve the issue, remove
the flexible hose and rethread, checking to make sure the
connection is secure. Make sure to use pipe tape.
4. - Metal nut became loose
5.A - Debris in aerator
5.B - Wear and tear on button
4. - From under the counter, use an adjustable wrench and
tighten the metal nut to the hollow pipe. Make sure the faucet is
perpendicular to the counter.
5.A - Remove and clean aerator.
5.B - Contact Vigo Technical Support for replacement.
PARTS LIST - For any parts needed but not shown, please contact Vigo Technical Support
PART
Pull out Hose (black nylon)
Sprayer
Handle Lever
Handle Set Screw
Handle Body
Sedal Cartridge
Metal braided Hose
Sprayer Washer
Black Washer with Screen
PART #
FINISH
74001
74006
78009A
78009B
78009C
74035
74020
74008
74010
CH, ST, MB
CH, ST, MB
CH, ST, MB
CH, ST, MB
CH, ST, MB
-
SUPPLY DATE INDICATOR (INTERNAL USE ONLY)
W
W
W
W
W
W
W
W
W
TOLL FREE: (866) 591 - 7792
E-Mail: techmail@vigoindustries.com
www.vigoindustries.com
NSF / ANSI 61
5
VIGO INDUSTRIES, LLC ("VIGO")
FAUCET LIMITED LIFETIME WARRANTY
EFFECTIVE APRIL 1, 2013
VIGO offers the following limited warranty on each of its Faucet products (the "Product") and the components thereof. This warranty extends only to the original owner
for personal household use. For commercial uses, additional limitations apply.
VIGO warrants the structure of the Product to be free from defects in workmanship and materials under normal use and service for the period commencing from the
initial date of purchase by the owner, contractor, or builder, from VIGO or an authorized VIGO dealer, through the lifetime of the original owner or end-user.
VIGO warrants the cartridge component of the Product to be free from defects in workmanship and materials under normal use and service for a period of five (5) years
from the initial date of purchase by the owner, contractor, or builder, from VIGO or an authorized VIGO dealer.
VIGO warrants the spray assembly and other mechanical components of the Product to be free from defects in workmanship and materials under normal use and
service for a period of one (1) year from the initial date of purchase by the owner, contractor, or builder, from VIGO or an authorized VIGO dealer.
Subject to the Warranty Service provision below, any product reported to the authorized dealer or to VIGO as being defective within the warranty period will be repaired
or replaced (with a product of equal value) at the option of VIGO. This warranty extends to the original owner and is not transferable to a subsequent owner.
Neither the distributor, authorized VIGO dealer, nor any other person has been authorized to make any affirmation, representation, or warranty other than those
contained in this warranty. Any affirmation, representation, or warranty other than those contained in this warranty shall not be enforceable against VIGO or any other
person.
VIGO reserves the right to modify this warranty at any time, it being understood that such modifications will not alter the warranty conditions applicable at the time of
sale of the products in question.
Limitations
This warranty shall not apply to instances of incorrect operating procedures, breakages, or damages caused by fault through improper installation, carelessness, abuse,
misuse, misapplication, improper maintenance, or alteration of the Product, as well as chemical or natural corrosion, accident, fire, flood, an act of God, or any other
casualty. Avoid abrasive cleaners, steel wools, and harsh chemicals as these will scratch, damage, and / or dull the product and / or finish and void this warranty. The
owner of the Product covered by the present warranty is entirely responsible for its proper installation and any applicable plumbing or electrical wiring. VIGO neither
installs nor supervises the installation nor hires a contractor for this purpose; consequently, VIGO cannot be held responsible for any default, breakage, or damages
caused thereby or resulting thereof, either directly or indirectly.
The owner must provide access to the components of the Product as described in the installation guide so that VIGO can execute the warranty specified herein. If such
access is not available, all expenses to provide said access will be the responsibility of the owner.
This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied by VIGO and all applicable rules, regulations,
and legislation pertaining to such installations.
This warranty does not apply unless the VIGO Product is installed by fully insured licensed professionals. Vigo strongly recommends that such licensed professionals
have experience in the installation of bathroom and kitchen products. [Installation of certain products, including without limitation glass products (i.e., shower doors and
glass sinks) by an inexperienced person may result in product failure including, but not limited to, glass breakage which could result in personal injury or death.]
VIGO is not liable for personal injuries or deaths to any persons or for any direct, special, incidental, or consequential damage, loss of time, loss of profits,
inconvenience, incidental expenses, labor or material charges, or any other costs resulting from the use of the product or equipment or pertaining to the application of
the present warranty, or resulting from the removal or replacement of any product or element or part covered by this warranty.
EXCEPT AS OTHERWISE PROVIDED ABOVE, VIGO MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE OR COMPLIANCE WITH ANY CODE.
In any case, VIGO cannot be held liable for any amount over and above the purchase price paid for the Product by the owner/end-user, contractor, or builder.
Commercial Limitations
In addition to the above conditions and limitations, the warranty period for products installed for commercial applications or used in commercial ventures is one (1) year
from the initial date of purchase by the owner, contractor, or builder from an authorized dealer. VIGO is not responsible for loss of use or profit under any circumstances.
If the product is used as a display, the warranty period begins from the date of purchase. This warranty gives the owner specific legal rights. The owner may also have
other rights which can vary from one state or province to another.
Warranty Service
In order to obtain service provided under this warranty during regular business hours, contact the dealer or distributor who sold the unit, or contact VIGO directly. VIGO
will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered by the warranty; the user has
informed an authorized VIGO Agent or VIGO's warranty service department representative of the nature of the problem during the warranty period; conclusive evidence
(e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period; an
authorized independent service person or company representative has been permitted to inspect the product during regular business hours within a reasonable time
after the problem was reported by the user. Vigo's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the
tender terminates VIGO's warranty obligations.
Certification may be ended by VIGO or certification agencies without notice.
6
Download PDF

advertising