Models C801, C801R, F802, P802, C803, C803R, C804
Wendy's Grills
Operating Instructions
072493-M
5/22/09 (Original Publication)
(Updated 6/5/12)
Table of Contents
Section 1
To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Setup and Checkout Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Ventilation and Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Grease Disposal Container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Section 2
To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Section 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Section 4
Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
C801 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
C801 Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
F802 Front Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
P802 Pick Up Window Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
C803 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
C803 Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
C804 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Accessories - Supplied By Taylor Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Accessories Not Supplied By Taylor Company Obtain From Wendy's Small Wares Vendors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
Section 5
Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
C801 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
C801 Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
F802 Front Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
P802 Pick Up Window Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
C801/C801R/F802/P802/C803/C803R/C804
Table of Contents
Table of Contents - Page 2
C803 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
C803 Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
C804 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
Section 6
Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
Morning Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
Cook to Order Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
Nightly Cleaning Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
Section 7
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
Section 8
Warranty Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
Labor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
Section 9
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
Note: Continuing research results in steady improvements; therefore, information
in this manual is subject to change without notice.
Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.
E May, 2009 Taylor (Original Publication)
(Updated June, 2012)
072493-M
The word Taylor and the Crown design
are registered trademarks in the United States
of America and certain other countries.
Table of Contents
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
C801/C801R/F802/P802/C803/C803R/C804
Section 1
To the Installer
The following are general installation instructions.
For complete installation details, please see the
check out card.
This unit has many sharp edges that can
cause severe injuries.
Installer Safety
Electrical Connections
In all areas of the world, equipment should
be installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.
Electrical connections to the grill must be provided
and arranged by Wendy's, with their preferred
licensed electrician. This must be completed
immediately following grill installation and prior to the
grill Start Up and Checkout by the local Taylor
representative.
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
service of Taylor equipment.
S
S
S
S
Check the data plate on the grill for voltage, cycle,
phase and electrical specifications. The power
connections are located behind the access cover of
the control box under the front staging side of the
grill.
Only Taylor authorized service personnel
should perform installation and repairs on
the equipment.
Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.
Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and
service.
Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment.
In the United States, this equipment is intended to
be installed in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70-1987. The
purpose of the NEC code is the practical
safeguarding of persons and property from hazards
arising from the use of electricity. This code contains
provisions considered necessary for safety.
Compliance therewith and proper maintenance will
result in an installation essentially free from hazard!
In all other areas of the world, equipment should be
installed in accordance with the existing local codes.
Please contact your local authorities.
The Proper Wire Size and Branch Circuit
Overcurrent Device shall be selected according to
the data label information and in accordance with
CEC Part I 2006, Section 14-100(e)(i). Incoming
power must be connected to the line side of the
power contactor.
The main power supply(s) to the equipment
must be disconnected prior to performing any
repairs. Failure to follow this instruction may result in
personal injury or death from electrical shock or
hazardous moving parts as well as poor
performance or damage to the equipment.
FOLLOW YOUR LOCAL ELECTRICAL CODES!
Note: All repairs must be performed by an
authorized Taylor Service Technician.
C801/C801R/F802/P802/C803/C803R/C804
1
To the Installer
Installation
CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!
These machines are designed for indoor use
only.
The C801 grill and the C801 Reverse grill must be
lifted and positioned in place with the aid of a lift
device. They are suspended between the adjacent
sandwich counter and the meat well.
This unit is provided with an equipotential
grounding lug that is to be properly attached to the
rear of the frame by the authorized installer. The
installation location is marked by the equipotential
bonding symbol (5021 of IEC 60417-1) on both the
removable panel and the equipments frame.
The F802,C803, C803 Reverse, and C804 grills are
mounted on carts. They are wheeled into position in
the store.
The P802 grill is installed into the sandwich counter.
The items to be installed / connected by the
distributor include:
S
S
S
S
S
S
Stationary appliances which are not
equipped with a power cord and a plug or
another device to disconnect the appliance
from the power source must have an all-pole
disconnecting device with a contact gap of
at least 3mm installed in the external
installation.
Appliances that are permanently connected
to fixed wiring and for which leakage
currents may exceed 10 mA, particularly
when disconnected or not used for long
periods, or during initial installation, shall
have protective devices such as a GFI, to
protect against the leakage of current,
installed by the authorized personnel to the
local codes.
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or
other equivalent synthetic
elastomer-sheathed cord (Code designation
60245 IEC 57) installed with the proper cord
anchorage to relieve conductors from strain,
including twisting, at the terminals and
protect the insulation of the conductors from
abrasion.
To the Installer
Node board modules
Lane dividers
Miscellaneous accessory brackets
DO NOT install the machine in an area
where a water jet could be used to clean or rinse the
machine. Failure to follow this instruction may result
in serious electrical shock.
This grill must be installed on a level
surface. Failure to comply may result in personal
injury or equipment damage.
2
C801/C801R/F802/P802/C803/C803R/C804
Step 9
Once the gaps are set, install the cook side back
splash, lane divider, and the release sheets.
Setup and Checkout Instructions
Step 1
Install the panels, starting with the bottom. Install the
panels under the node board modules, the lane
dividers (staging side) and the accessory brackets.
Step 2
Install the node board modules.
Step 10
Cook one run of product on each platen to check the
product appearance and the finished product
temperature. (Internal temperature must be above
175°F / 79°C.)
Step 3
Tighten all screws.
Step 11
Check the “cook to order” and back up staging.
Step 4
Once the electrical connections are completed,
install the box cover and turn the grill on.
Step 12
Fill out the checkout card and the work order /
invoice.
Step 5
Wait for 45 minutes for the grill to reach stable
temperatures before proceeding to the next step.
The grill will indicate it is ready to cook in
approximately 15 - 20 minutes.
Ventilation and Clearance
CAUTION: The grill will be hot. Wear
proper protective equipment to avoid severe burns
from high temperatures.
To ensure proper operation of this appliance, it must
be installed so that the products of combustion are
efficiently removed.
Step 6
Check the platen lift mechanism and adjust, if
needed (not applicable to P802). (See Lift/Latch
Instructions in the Service Manual.)
After set up, do not store anything on top of
the grill. Failure to follow this instruction may result
in a fire hazard.
Step 7
Install the back panel.
Step 8
The platen should be lowered onto the lower plate
and the gap settings should be properly calibrated.
To close the platen, touch and hold the red button
corresponding to the desired platen. A cook cycle
will not start and the display will read “Standby”.
Release the button after the platen has closed. (See
Platen Gapping Procedures in the Service
Manual.)
C801/C801R/F802/P802/C803/C803R/C804
Grease Disposal Container
In order to comply with NSF Standard 4
requirements, an appropriate grease disposal
container must be provided. This container is
supplied by the KES, not the Taylor Company.
3
To the Installer
Section 2
To the Operator
The grill you have purchased has been carefully
engineered and manufactured to provide
dependable operation.
Note: Constant research results in steady
improvements; therefore, information in this
manual is subject to change without notice.
This grill, when properly operated and maintained,
will produce a consistent quality product. Like all
mechanical products, they require cleaning and
maintenance. A minimum amount of care and
attention is necessary if the operating procedures in
this manual are followed closely.
This Operator's Manual should be read before
operating or performing any maintenance on your
equipment.
If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other
similar legislation in effect after August 13, 2005.
Therefore, it must be collected separately after its
use is completed, and cannot be disposed as
unsorted municipal waste.
It is strongly recommended that all personnel
responsible for the equipment's operation and
cleaning, review these procedures for proper training
and assurance that no misunderstandings exist.
The user is responsible for returning the product to
the appropriate collection facility, as specified by
your local code.
In the event that you require technical assistance,
please call 877-222-7010 for authorized service.
Note: Warranty is valid only if the parts are
authorized Taylor parts, purchased from an
authorized Taylor Distributor, and the required
service work is provided by an authorized Taylor
service technician. Taylor reserves the right to deny
warranty claims on equipment or parts if
non-approved parts or refrigerant were installed in
the machine, system modifications were performed
beyond factory recommendations, or it is determined
that the failure was caused by neglect or abuse.
To the Operator
For additional information regarding applicable local
laws, please contact the municipal facility and/or
local distributor.
4
C801/C801R/F802/P802/C803/C803R/C804
Section 3
Safety
We at Taylor Company are deeply concerned about
the safety of the operator when he or she comes in
contact with the grill and its parts. Taylor has gone
to extreme efforts to design and manufacture built-in
safety features to protect both you and the service
technician. As an example, warning labels have
been attached to the grill to further point out safety
precautions to the operator.
S
Stationary appliances which are not
equipped with a power cord and a plug or
other device to disconnect the appliance
from the power source must have an all-pole
disconnecting device with a contact gap of
at least 3 mm installed in the external
installation.
S
Appliances that are permanently connected
to fixed wiring and for which leakage
currents may exceed 10 mA, particularly
when disconnected or not used for long
periods, or during initial installation, shall
have protective devices such as a GFI, to
protect against the leakage of current,
installed by the authorized personnel to the
local codes.
S
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or
other equivalent synthetic
elastomer-sheathed cord, (Code designation
60245 IEC 57), installed with the proper
cord anchorage to relieve conductors from
strain, including twisting, at the terminals
and protect the insulation of the conductors
from abrasion.
Please call 877-222-7010 for authorized service.
To Operate Safely:
DO NOT operate the grill without reading
this operator's manual. This manual should be kept
in a safe place for future reference.
Per IEC 60335-1 and its part 2 standards,
“This appliance is to be used only by trained
personnel. It is not intended for use by children or
people with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge,
unless given supervision or instruction concerning
the use of the appliance by a person responsible for
their safety.”
IMPORTANT: DO NOT use a water jet or
spray excessive water on or anywhere near the
grill. Failure to follow this instruction may result in
serious electrical shock and cause permanent
electrical and mechanical damage to internal parts.
Failure to follow this instruction may result in:
Failure to follow the instructions below may
result in severe injury or death from electrocution:
S
S
S
DO NOT operate the grill unless it is
properly grounded.
DO NOT attempt any repairs unless the
power supply to the grill has been
disconnected (must be performed by an
authorized service technician).
DO NOT operate the grill unless all service
panels are restrained with screws.
S
serious electrical shock
S
burns from hot steam
S
liquid collecting inside the grill and
destroying electrical components.
120605
C801/C801R/F802/P802/C803/C803R/C804
5
Safety
DO NOT use cold water or ice to cool the
upper cook surface, the lower cook surface, or the
staging grill plate. Failure to follow this instruction
may result in:
S
serious electrical shock
S
burns from hot steam
S
Appropriate grill clearance must be
maintained from all combustible materials. Failure to
comply could result in a fire hazard.
Take caution to protect eyes, lungs, and all
parts of the body from potential harm when using
any chemical cleaner. Failure to follow this
instruction may result in a chemical burn.
DO NOT use any abrasives or cleaners
other than approved food service cleaners and
degreasers. Failure to comply may cause illness to
the consumer and may also damage grill surfaces.
liquid collecting inside the grill and
destroying electrical components.
Failure to follow the instructions below may
result in severe burns from high temperatures:
S DO NOT prepare or remove product without
proper equipment.
S DO NOT allow untrained personnel to
operate this grill.
S USE EXTREME CAUTION when cleaning
the grill.
Safety
This grill must be installed on a level
surface. Failure to comply may result in personal
injury or equipment damage.
NOISE LEVEL: Airborne noise emission does not
exceed 70 dB(A) when measured at a distance of
1.0 meter from the surface of the machine and at a
height of 1.6 meters from the floor.
6
C801/C801R/F802/P802/C803/C803R/C804
Section 4
Operator Parts Identification
C801
Figure 1
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
HANDLE-ADJUST-PLATEN
070647
6
PANEL A.-SPLASH SHLD W/SP
X70783
2
PLATEN A.-ADJUSTABLE
X71825-23
7
DIVIDER A.-2 LANE
070847
3
HANDLE-LIFT-PLATEN
072711
8
DIVIDER A.-3 LANE *STAGE
070848
4
PLATEN A.-4OZ
X71824-23
9
SHIELD-BACKSPLASH
070765
5
PLATEN A.-2OZ
X71823-23
10
DIVIDER A.-COOK
070851
C801/C801R/F802/P802/C803/C803R/C804
7
Operator Parts Identification
C801 Reverse
Figure 2
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
DIVIDER A.-3 LANE *STAGE
070848
6
PLATEN A.-ADJUSTABLE SERV
X71825-23
2
DIVIDER A.-*2 LANE*STAGE
070847
7
HANDLE-ADJUST-PLATEN
070647
3
PANEL A.-SPLASH SHIELD
W/SPEAKER
X72247
8
HANDLE-LIFT-PLATEN
072711
9
DIVIDER A.-COOK
070851
4
PLATEN A.-*C801* 2 OZ SERV
X71823-23
SHIELD-BACKSPLASH
070765
5
PLATEN A.-*C801* 4 OZ
X71824-23
Operator Parts Identification
10
8
C801/C801R/F802/P802/C803/C803R/C804
F802 Front Unit
Figure 3
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
DIVIDER A.-2 LANE
070847
5
PLATEN A.-SERVICE ADJ
X71825-23
2
HANDLE-LIFT-PLATEN
072711
6
SHIELD-BACKSPLASH
071732
3
HANDLE-ADJUST-PLATEN
070647
7
DIVIDER A.-COOK
070851
4
PLATEN A.-SERVICE ADJ LEFT
X72669-23
C801/C801R/F802/P802/C803/C803R/C804
9
Operator Parts Identification
P802 Pick Up Window Unit
Figure 4
ITEM
1
DESCRIPTION
DIVIDER A.-*2 LANE
Operator Parts Identification
PART NO.
070847
10
C801/C801R/F802/P802/C803/C803R/C804
C803
Figure 5
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
HANDLE-LIFT-PLATEN
072711
6
SHIELD-BACKSPLASH
070765
2
HANDLE-ADJUST-PLATEN
070647
7
DIVIDER A.-COOK
070851
3
PLATEN A.-ADJUSTABLE SERV
X71825-23
8
DIVIDER A.-2 LANE STAGE
070847
4
PLATEN A.-*C801* 4 OZ SERV
X71824-23
9
DIVIDER A.-3 LANE STAGE
070848
5
PLATEN A.-*C801* 2 OZ SERV
X71823-23
C801/C801R/F802/P802/C803/C803R/C804
11
Operator Parts Identification
C803 Reverse
Figure 6
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
DIVIDER A.-2 LANE
070847
6
SHIELD-BACKSPLASH
070765
2
HANDLE-LIFT-PLATEN
072711
7
DIVIDER A.-COOK
070851
3
PLATEN A.-2 OZ
X71823-23
8
HANDLE-ADJUST-PLATEN
070647
4
DIVIDER A.-3 LANE STAGE
070848
9
PLATEN A.-ADJUSTABLE
X71825-23
5
PLATEN A.-4 OZ
X71824-23
Operator Parts Identification
12
C801/C801R/F802/P802/C803/C803R/C804
C804
Figure 7
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
HANDLE-LIFT-PLATEN
072711
5
SHIELD-BACK SPLASH
071732
2
HANDLE-ADJUST-PLATEN
070647
6
DIVIDER A.-COOK
070851
3
PLATEN A.-SERVICE ADJ
X71825-23
7
PLATEN A.-SERVICE ADJ LEFT
X72669-23
4
DIVIDER A.-2 LANE
070847
C801/C801R/F802/P802/C803/C803R/C804
13
Operator Parts Identification
Accessories - Supplied By Taylor Company
Figure 8
ITEM
DESCRIPTION
1
SHIELD A.-LOCATING BUCKET
X71284
5
BRACKET-RELEASE SHEET
070707
2
SHELF A.-MEAT LOADING
X70944
6
DIVIDER A.-3 LANE *STAGE
070848
3
SHIELD-BACKSPLASH
070765
7
DIVIDER A. *COOK
070851
4
CLIP-RELEASE SHEET
070709
8
DIVIDER A. *2 LANE
070847
Operator Parts Identification
PART NO.
ITEM
14
DESCRIPTION
PART NO.
C801/C801R/F802/P802/C803/C803R/C804
Accessories Not Supplied By Taylor Company Obtain From Wendy's Small Wares Vendors
Figure 9
ITEM
DESCRIPTION
ITEM
DESCRIPTION
1
HOLDER-SQUEEGEE
6
SPATULA-WHITE HANDLE-SERVING
2
HANDLE-SQUEEZE
7
3
TOOL-TRANSFER
HOLDER-WHITE HANDLED SERVING
SPATULA
4
SPATULA-RED HANDLE-SERRATED
8
TROUGH
5
SPATULA-RED HANDLE-SERVING
9
SHEET-RELEASE
C801/C801R/F802/P802/C803/C803R/C804
15
Operator Parts Identification
Section 5
Important: To the Operator
C801
Figure 10
ITEM
1
2
3
4
DESCRIPTION
PART NO.
PANEL A.-SPLASH SHIELD
W/SPEAKER
X70783
KIT A.-NODE-REAR W/HARN
KIT A.-NODE-COOK W/HARN
KIT A.-NODE-FRONT W/HARN
X72136
X72134
X72135
Important: To the Operator
ITEM
16
DESCRIPTION
PART NO.
5
CONTROL-C801 NODE I/O
071242-SER
6
CONTROL-RESET SWITCH
10A/230
070717
7
LIGHT-RED 230V
070880-27
C801/C801R/F802/P802/C803/C803R/C804
C801 Reverse
Figure 11
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
KIT A.-NODE REAR C801
W/HARN
X72136
5
NODE A.-COMPLETE C801R
COOK
X72254
2
PANEL A.-SPLASH SHIELD
W/SPEAKER
X72247
6
NODE A.-COMPLETE C801R
STG F
X72243
3
CONTROL-RESET SWITCH
10A/250
070717
7
CONTROL C801 MODE I/O
071242-SER
4
LIGHT-RED 230V
070880-27
C801/C801R/F802/P802/C803/C803R/C804
17
Important: To the Operator
F802 Front Unit
Figure 12
ITEM
1
2
DESCRIPTION
PART NO.
NODE A.-COMPLETE F802
STAGE/COOK
X71550-SER
CONTROL-C801 MODE I/O
071242-SER
Important: To the Operator
ITEM
18
DESCRIPTION
PART NO.
3
LIGHT-RED 230V
070880-27
4
CONTROL-RESET SWITCH
10A/250
070717
C801/C801R/F802/P802/C803/C803R/C804
P802 Pick Up Window Unit
Figure 13
ITEM
1
2
DESCRIPTION
PART NO.
NODE A.-COMPLETE P802
STAGE/COOK
X71593-SER
CONTROL C801 MODE I/O
071242-SER
C801/C801R/F802/P802/C803/C803R/C804
ITEM
19
DESCRIPTION
PART NO.
3
LIGHT-RED-230V
070880-27
4
CONTROL-RESET SWITCH
10A/250
070717
Important: To the Operator
C803
Figure 14
ITEM
1
DESCRIPTION
PART NO.
NODE A.-COMPLETE C803
COOK
X72062
2
KIT A. NODE-FRONT C801
W/HARN
X72135
3
CONTROL-C801 MODE I/O
071242-SER
Important: To the Operator
ITEM
20
DESCRIPTION
PART NO.
4
LIGHT-RED 230V
070880-27
5
CONTROL-RESET SWITCH
10A/230
070717
C801/C801R/F802/P802/C803/C803R/C804
C803 Reverse
Figure 15
ITEM
DESCRIPTION
PART NO.
1
NODE A.-COMPLETE
*STAGING
X72243
2
NODE A.-COMPLETE *COOK
X72254
3
CONTROL-C801 MODE I/O
071242-SER
C801/C801R/F802/P802/C803/C803R/C804
ITEM
21
DESCRIPTION
PART NO.
4
LIGHT-RED 230V
070880-27
5
CONTROL-RESET-SWITCH
10A/250
070717
Important: To the Operator
C804
Figure 16
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
NODE A.-COMPLETE
X73057
4
LIGHT-RED 230V
070880-27
2
HARNESS-NODE
073154
5
CONTROL-RESET SWITCH
070717
3
CONTROL-MODE I/O
071242-SER
Important: To the Operator
22
C801/C801R/F802/P802/C803/C803R/C804
The following symbols are used on the control mode
display:
The COOK AND STAGE symbol will be illuminated
when the control mode is in the LUNCH COOK AND
STAGE mode.
= Idle (blue illumination)
= Cook Only (amber illumination)
= Cook and Stage (green illumination)
The IDLE symbol will be illuminated when the
control mode is in the OFF mode.
Figure 19
The COOK ONLY and COOK AND STAGE symbols
will be illuminated when the control mode is in the
BREAKFAST mode.
Figure 17
The COOK ONLY symbol will be illuminated when
the control mode is in the LUNCH COOK ONLY
mode.
Figure 20
Figure 18
C801/C801R/F802/P802/C803/C803R/C804
23
Important: To the Operator
The following symbols are used on the cook and
serve displays.
situation, any cooked meat in the staging section
and any meat in the cooking section must be
removed from the grill. The cooked meat from the
staging section is placed in the chili meat pan and
the partially cooked meat is discarded.
= 4 oz.
To restart the grill, push in on the master power
switch to restore power to the controls. If the back
up memory has expired, turn on the grill per
standard procedures. When the switch is pushed in,
the red lights will extinguish.
= 2 oz.
The master power switch is located on the Line 2
side of the grill, beneath the node panel.
= Eggs
Grill Operation
= Sausage
Each grill has a lower cook surface. Excluding the
Model P802, they also have two or more upper
platens. One or more of the upper platens is
adjustable. Adjustable platens can be adjusted to
cook either 2 oz. or 4 oz. patties.
= Hot Meat
To change the product size on the adjustable platen,
shift the lever on the front of the platen up or down
so that the display shows the desired patty size.
Place the lever in the up position for 4 oz. patties
and in the down position for 2 oz. patties.
= Chicken
= Red Chef Hat
Master Power Switch
The Double-Sided Grill (DSG) is equipped with a
master power switch, which is only used when the
grill needs to be quickly shut down.
In this situation, pulling out on the switch
immediately removes power from the control
circuits. Two red lights illuminate to indicate that the
power to both power circuits has been interrupted.
Figure 21
There is a one minute memory backup that allows
the grill to maintain all timing control states in the
event of a power loss. Once this backup period
expires, all timing control functions are lost. In this
Important: To the Operator
A minimum of one patty and a maximum of eight 4
oz. or ten 2 oz. patties may be cooked under one
grill platen.
24
C801/C801R/F802/P802/C803/C803R/C804
Health and Safety
Follow proper procedures to prevent
food contamination and health hazards!
CAUTION: Be careful not to touch the grill
or splash hot meat juices while scraping or cleaning
the grill. The top grill platens are extremely hot
(380ºF / 193_C) and can easily cause burns.
Wash hands before and after handling raw meat or
the grill operator utensils to prevent contamination
and health hazards.
Cooked ground beef must reach a minimum internal
temperature of 175ºF (79.4_C).
C801/C801R/F802/P802/C803/C803R/C804
25
Important: To the Operator
Section 6
Operating Procedures
Approximately half of each grill is dedicated to
cooking and the other half is used for staging cooked
meat.
Morning Procedures
The top platens and release sheets are cleaned
during the Morning Procedures.
Each model has a lower cook surface. Excluding the
P802, each model also has two or more upper
platens. The two-sided cooking concept ensures
quick, even cooking of both sides of the products
placed on the lower surface. The upper platens are
labeled to indicate which patty size can be cooked
under that platen (2 oz. or 4 oz.).
Assemble the following tools:
S
S
S
S
S
One or more of the upper platens is adjustable. This
adjustable platen can be adjusted to cook either 2
oz. or 4 oz. patties.
Blue scrub
DCT Heavy Duty Degreaser
Dry white towel
1/6-sized, 4-inch deep pan of water
Vinyl gloves
If an adjustable platen is chosen, rotate the lever up
for 4 oz. patties and down for 2 oz. patties. The lever
is attached to an over-center device to ensure a
positive selection of the proper gap.
CAUTION: The grill must remain in the
OFF position for cleaning. (The grill should be
cool.) Failure to follow this instruction may result in
severe burns from high temperatures.
Sensors detect the lever position They indicate “2
oz.” or “4 oz.” on the display and make all
appropriate timing adjustments.
Removing Platen Release Sheets
Step 1
The upper platen must be in the UP position in order
to remove the platen release sheet.
Step 2
Pull the retainer clip off of the release sheet bracket
located on the front of the platen. The release sheet
will drop loose.
Step 3
Remove the release sheet bracket from the front of
the platen. Set it aside on the staging side of the
grill.
Step 4
Lift the rear release sheet bracket assembly off the
rear of the platen. The release sheet and the bracket
assembly will come off of the platen together.
Figure 22
A minimum of one patty and a maximum of eight 4
oz. or ten 2 oz. patties may be cooked under one
grill platen.
Step 5
Remove the retainer clip and the release sheet
bracket from the release sheet and set them aside
on the staging side of the grill.
We begin our instructions with the Morning
Procedures.
Step 6
Lay the release sheet flat on the staging side of the
grill.
Note: The Model C801 has been selected to
illustrate the step-by-step operating procedures.
Operating Procedures
26
C801/C801R/F802/P802/C803/C803R/C804
Step 7
Repeat these steps for the remaining platens.
Reinstall the Platen Release Sheets
Replace release material sheets if:
S
S
S
Step 1
Lay the sheet out flat on the staging side of the grill.
Release sheet is torn
Release sheet is worn
Product sticks to the release sheets
Step 2
Lay the release sheet bracket on the top edge of the
release sheet with the notches on the bar facing up
and the inside of the angle facing toward you.
Cleaning Platens
Step 1
Wearing vinyl gloves, spray a light layer of DCT
Heavy Duty Degreaser on the platen surface.
Step 2
Using the blue scrub pad, scrub the platen surface
with an up and down motion.
IMPORTANT: Grill screens and Scotch Bricks
must NOT be used to clean the top platens. They
will damage the cooking surfaces.
Step 3
Continue scrubbing until the entire platen grill
surface is clean and no carbon build-up is visible.
Step 4
Clean the sides and top of the platen as necessary.
Figure 23
Step 5
Wipe the platen surface with a damp towel. Rinse
the towel and re-wipe several times to remove any
remaining residue.
Step 3
Fold the end of the sheet in toward the bend of the
release sheet bracket. Center the sheet between the
notches. Place the edge of the sheet flush against
the inside angle.
Cleaning Platen Release Sheets
Step 1
Wipe the platen sheet using a damp towel. To
remove heavy carbon build-up, spray DCT Heavy
Duty Degreaser on the platen sheet and scrub
thoroughly with a damp towel.
Step 2
Wipe the platen sheet dry and re-install it on the
platen surface.
Note: When re-installing the platen sheet, reverse it
every day to prolong the life of the sheet.
Step 3
Repeat these steps for the remaining platen
release sheets.
C801/C801R/F802/P802/C803/C803R/C804
Figure 24
27
Operating Procedures
Step 4
Hold the release sheet in place using downward
pressure. Roll the release sheet bracket forward 90°.
Re-attach the retainer clip, making sure the clip is
centered on the release sheet bracket.
Step 6
Close the platen while pulling back on the release
sheet.
Figure 27
Step 7
Lift the release sheet up against the front of platen
and hold it in place.
Figure 25
Step 5
With the release sheet bracket notches facing down
and the retainer clip facing the back of the grill, slide
the notches of the release sheet bracket onto the
rear release sheet bracket.
Figure 28
Step 8
Install the release sheet bracket onto the front
release sheet bracket.
Figure 26
Note: Lower the platen(s) next to the platen being
worked on to ease the installation of the rear release
sheet bracket.
Operating Procedures
Figure 29
28
C801/C801R/F802/P802/C803/C803R/C804
Step 11
Make sure the platen sheet is firmly positioned
between the front and rear holding brackets. The
platen sheet must fit flat to the bottom and sides of
the platen. Never fold or crease the platen sheet
while handling. It should not be wrinkled or bowed
when properly installed.
Step 9
Pull the release sheet tight and fold it over the top of
the release sheet bracket.
Figure 30
Step 10
Hold the sheet in place and re-install the retainer
clip.
Figure 32
The platen sheet helps keep residue from
accumulating between the platens, which adversely
impacts cooking performance.
Step 12
Repeat these steps on the remaining platens to
reinstall the release sheets.
Step 13
After all the platens and the release sheets are
cleaned and reinstalled, wipe the cooking and
staging sides of the grill surface with a damp towel.
This will remove any residue that may have fallen
while cleaning the platens and release sheets.
Figure 31
C801/C801R/F802/P802/C803/C803R/C804
29
Operating Procedures
Grill Start-Up
Step 1
Before turning on the grill, ensure that the rear
splash guard and the cook divider are installed and
that the platens are closed.
Figure 35
CAUTION: The grill surfaces will become
hot. (See the “Safety” section on page 5.)
Step 4
While the grill is heating, the display on the cooking
Figure 33
or
side will be red and will show
until the cooking section reaches the proper cooking
temperature.
Step 2
Install the staging lane dividers.
Note: Refer to page 24 for examples of other menu
items.
Step 5
The display will turn green and read
or
(depending on the platen setting) when the
cooking side reaches the correct temperature.
Step 6
While the grill is heating, the display on the staging
until the staging
side will be red and show
section reaches the proper cooking temperature.
Step 7
The staging side displays will turn green and read
Figure 34
Step 3
Touch the COOK/STAGE button on the main control
switch located on the front of the grill below the
cooking controls. The lights around the button will
illuminate green. Allow the grill to pre-heat for 20
minutes.
Operating Procedures
when the staging side reaches the correct
temperature.
Step 8
Make sure the grease bucket is directly under the
grease chutes.
30
C801/C801R/F802/P802/C803/C803R/C804
Step 9
Set up the grill area as directed by Wendy's
Operating Procedures.
Operating Procedures
Cooking Patties
Figure 36
Note: If the platen doesn't automatically raise, the
platen can be lifted manually with a sharp upward
tug.
Step 1
Following Wendy's Operating Procedures, quickly
lay the patties on the section of the grill selected for
the meat size being cooked. The display indicates
either
or
Step 5
.
An orange display flashes
when the cook
cycle finishes and the platen is raising.
Step 2
Lay the patties between the holes on the cook
divider, 1/2 inch in from the sides of the dividers.
Step 6
Follow Wendy's procedures to transfer the cooked
patties to the staging lanes.
Step 7
Confirm the patty transfer by touching the
CAUTION: The top platen is extremely
HOT! (See the “Safety” section on page 5.)
Step 3
Immediately close the lid to start the cook cycle.
appropriate buttons (
stage lane display.
The display will change to orange
Note: The red buttons are reserved for the cook
and the white buttons are reserved for those
handling ready-to-serve food.
or
or
) on the
, and a bar graph will indicate the cook cycle
progress.
Step 8
Use the squeegee scraper after each run of product
to remove excess juice from the grill platens and the
cooking surface.
Step 4
At the end of the cook cycle, an alarm will sound
once and the platen will automatically raise.
IMPORTANT: DO NOT use the metal side of the
scraper on the platen or the release sheet.
Damage will occur!
C801/C801R/F802/P802/C803/C803R/C804
31
Operating Procedures
Cleaning Between Product Runs
Standby
After each run of product, the grill should be cleaned
to ensure proper cooking.
When not in consistent use, the grill platens should
be closed to reduce heat in the grill area and to
conserve energy.
Step 1
Using a grill scraper, scrape the residue from the
lower cook surface.
Figure 38
Step 1
button
Touch and hold the red
corresponding to the desired platen while closing the
Figure 37
Step 2
Use a rubber wiper squeegee to clean the release
material on the upper cook surface. Hold the handle
at a slight upward angle with the wiper end facing
downward. Wipe the material using a downward
motion. DO NOT use extreme pressure or force.
Improper procedures will tear or crease the release
material.
platen. The display will indicate
to orange.
, and change
Step 2
Release the button after closing the platen. The
display will change to green.
Step 3
Open the platen to begin a cook cycle by touching
and holding the corresponding red button. The
platen will automatically raise.
Note: DO NOT use a scraper, sharp utensils, or
abrasives to clean the upper cook surface.
Step 3
When necessary, use a grill cloth to clean the back
splash shield and the strike plate areas. When
necessary, use the spatula to clean the front grease
trough. Periodically check the grease bucket for
excess grease and empty it as needed.
Temporary Staging
Follow Wendy's Operating Procedures to manage
the staging process.
Operating Procedures
Figure 39
32
C801/C801R/F802/P802/C803/C803R/C804
Cook Cycle Interrupted
Cook to Order Mode
Step 1
If the cook cycle is interrupted, the product that was
cooking must be discarded. The platen display will
turn red and an alarm will sound.
Step 1
During operating hours, water clean the cook side
grill surface as needed, using standard Wendy's
procedures.
Step 2
The display reads
close.
Step 2
A “Cook to Order” mode is provided for times when
it is desirable to shut down the staging side. Follow
Wendy's operating procedures when using this
function.
and the platen will not
Step 3
To deactivate the alarm, touch and hold the red
button for approximately one second, until the
display clears.
Figure 41
Step 4
Remove the meat from the grill and discard.
Step 3
The grill may be placed in the “Cook to Order“ mode
by touching and holding the “COOK ONLY“ button.
Amber lights will illuminate around the button.
CAUTION: DO NOT use this meat for chili
meat as it cannot be assured that it has been
properly cooked.
Step 4
Before the “Cook to Order” mode can be entered, all
timing functions must be cleared on the staging side,
and the staging side must be emptied.
Figure 40
C801/C801R/F802/P802/C803/C803R/C804
33
Operating Procedures
Step 1
Insure all timing functions have been cleared.
Nightly Cleaning Procedures
CAUTION! Before proceeding with the nightly
cleaning procedures, follow the safety
.
precautions
stated in the Safety Section,
starting on page 5. Failure to follow those
instructions may result in severe personal
injury or death.
Step 2
Raise the grill platens by touching the platen button.
IMPORTANT: To prevent damage to the grill,
please note the warnings below.
DO NOT apply water or cleaner/degreaser to any
part of the grill other than the cook surfaces.
Improper procedures will cause permanent electrical
and mechanical damage to internal parts.
DO NOT attempt to clean the release material
sheets by using a hot hose or by soaking them in
liquid. Failure to follow these instructions may result
in damage to the release material sheets.
Figure 42
DO NOT fold, crease or touch the release material
sheets with sharp objects. Failure to follow this
instruction may result in torn or creased release
material sheets.
Step 3
Turn off the grill cooking and staging sections by
touching and holding the “IDLE“ button on the main
control switch. The lights around the button will
illuminate blue.
DO NOT allow the grill scraper or any abrasive
cleaning materials to come in contact with the
release material sheets. Failure to follow these
instructions may result in damage to the release
material sheets.
CAUTION: The grill surfaces are hot.
(See the “Safety” section on page 5.)
DO NOT use grill screens on the upper cook
surface, the lower cook surface, or the staging grill
plate. Failure to follow this instruction may result in
damage to the grill surfaces.
Operating Procedures
Step 4
Put on safety equipment (gloves) and follow
Wendy's Nightly Cleaning Procedures.
34
C801/C801R/F802/P802/C803/C803R/C804
Step 5
Remove the following items to be washed, rinsed
and sanitized at the dish sink:
S
S
S
S
Step 9
Apply a light coat of shortening to the entire lower
cook surface.
Grill cook dividers
Grill staging lane divider
Rear splash guard
Meat loading shelf
Step 6
Water clean the grill surface per Wendy's standard
procedures. Use a Scotch Brick instead of a grill
screen.
Step 7
Leave the platens in the raised position overnight.
Step 8
Since the platens are very hot, cleaning the
platens and the release sheets will be completed the
next morning as a part of the Morning Procedures.
Figure 43
Step 10
Empty the grease bucket into the appropriate
container.
ALWAYS FOLLOW LOCAL HEALTH CODES.
C801/C801R/F802/P802/C803/C803R/C804
35
Operating Procedures
Section 7
PROBLEM
1.
2.
Grill will not heat.
One heat zone will not heat.
(A fault message will be
displayed.)
Troubleshooting Guide
PROBABLE CAUSE
REMEDY
a. Circuit breaker is tripped.
a. Reset the circuit breaker.
b. Master Power Switch (reset) is in
the OFF position.
b. Place the Master Power Switch in
the ON position.
c. Master Power Switch is faulty.
c. Contact a service technician.
d. A cook mode button has not been
pressed. The grill is still in the
IDLE mode.
d. Press the appropriate cook mode
button (COOK ONLY or COOK &
STAGE).
a. Heater is faulty.
a. Contact a service technician.
b. The thermocouple is faulty.
b. Contact a service technician.
c. Thermo overload is faulty.
c. Contact a service technician.
4.
One heat zone is overheating.
(The cook display will be blank
and illuminated in red.)
a. Thermocouple is faulty.
a. Contact a service technician.
5.
The upper cook surface will not
stay in the raised position.
a. Defective springs.
a. Contact a service technician.
6.
Product is under-cooked,
overcooked, or cooking unevenly.
a. Release material sheet is worn.
a. Replace the release material
sheet.
b. The adjustable platen handle is in
the wrong position.
b. Place the adjustable platen handle
in the correct position
(2 oz. or 4 oz.).
c. Heat zone is not heating.
c. Contact a service technician.
d. Upper cook surface has carbon
build-up.
d. Closing procedures must be
followed to remove carbon
build-up.
e. An incorrect item was placed on
the lower cook surface (example:
4 oz. patty placed in 2 oz. cook
position).
e. Place the item on the proper lower
cook surface.
Troubleshooting Guide
36
C801/C801R/F802/P802/C803/C803R/C804
The following information is from the Wendy's Troubleshooting Guide (part no. 064274). The “Checklist Before
Calling the Taylor Company Call Center” indicates the symptoms and appropriate action to take. The “After Hours
Service Call Protocol” lists the questions to expect when calling 877-222-7010 after 10:00 pm Central Time and
on weekends.
Checklist Before Calling the Taylor Company Call Center
SYMPTOM
Raw, Undercooked or
Overcooked, Burned
Patties
Cook Cycle Won't Start
(timing bar does not
display)
Platen Closed and Will
Not Open
CHECK
ACTION TO TAKE
a. Interference between platen or other object
(back splash, lane divider, release clips).
a. Install parts correctly to remove
obstructions.
b. Space between platen and grill surface to
appear equal all the way around platen.
b. If gap is visibly unequal, Call for Service.
c. Proper size patty (2 oz./4 oz.) placed under
correct platen.
c. Insure consistent use of the proper size
patties.
d. Patties spaced and positioned correctly to
insure full coverage by platen front, back
and sides.
d. Insure consistent, correct orientation and
placement of patties.
e. Meat temperature before laying patties
34°-40°F (1.1°C - 4.4°C) as stored.
e. Only use meat stored within the proper
pre-cook temperature range.
f. Any residue or carbon build-up on grill
surface.
f. Water scrape more frequently.
g. Release sheet condition.
g. Replace if worn or has pinholes.
h. Any residue or carbon build up on platen
surface behind sheet.
h. Insure daily cleaning procedures are
thoroughly and consistently followed.
i. Cook a full test run under adjustable and
corresponding fixed platen.
i. Compare same size patty from each platen.
If significantly different visually, Call for
Service.
j. From full test run take internal meat
temperatures following operations manual
procedures (insure thermometer is
accurate).
j. If temperatures 185°F - 200°F (85°C 93°C), no grill adjustment to be made.
Escalate to supervisor. If temperature is
below 175°F (79°C), Call for Service.
Is display green with meat size displayed?
a. If yes, does display change to timing bar
when platen is closed?
a. Normal operation, no action required.
b. If no, or timing bar does not display.
b. Press & Hold button five seconds. If normal
green display appears, close platen to start
cook cycle. If not, insure grill has preheated
for 30 minutes. Call for Service.
a. Is there a timer being displayed?
a. Let timing finish before proceeding.
b. Press & Hold button five seconds.
b. If platen won't open, and Up Arrow is
displayed, large font text or small font text,
note which and Call for Service.
C801/C801R/F802/P802/C803/C803R/C804
37
Troubleshooting Guide
SYMPTOM
Controls Don't Work
CHECK
ACTION TO TAKE
All cook displays show green with meat size?
a. If no.
a. Press & Hold button five seconds.
b. If yes AND stage displays show empty or
“--”.
b. Do Hard Reset by pulling out white master
switch for a full 60 seconds. Push White
switch in and restart grill.
c. If “a” or “b” are still no.
c. Press & Hold active stage button five
seconds to clear the lane.
d. If controls will not function as normal.
d. Do Hard Reset by pulling out white master
switch for a full 60 seconds. Push White
switch in and restart grill.
Code Displayed
a. Error code displayed as 2 lines of letters
and numbers.
a. Accurately note the display location and the
error code by line. Call for Service.
Platen Opens Before
Cook Cycle Ends
a. Was gap selector handle moved or not
completely seated on Adjustable Platen
during Cook Cycle?
a. Cook cycle will not complete if gap selector
is moved.
b. Was grill preheated for 30 minutes prior to
start of cook cycle?
b. Allow grill temperature to stabilize prior to
starting a cook cycle.
c. Above does not resolve issue.
c. Call for Service.
Troubleshooting Guide
38
C801/C801R/F802/P802/C803/C803R/C804
After Hours Service Call Protocol
Note: The “Checklist Before Calling the Taylor Company Call Center” form must be completed before
starting the “After Hours Service Call Protocol” side of the form.
1.
2.
3.
4.
1.
Name
Company
Grill or Frosty Machine Issue
Wendy's Corp. Assigned Site Number
4.
1.
If yes: go to question 4.
2.
If no: a follow up service call will be made the next business day.
Do you have one platen that will cook 2 oz. meat?
1.
If yes: a service call will be dispatched the next business day.
2.
If no: an emergency call will be dispatched.
4 oz. Meat Cooking Issue
a. Do you have one platen that will cook 4 oz. meat?
1.
If yes: a service call will be dispatched the next business day.
2.
If no: an emergency call will be dispatched.
Grill Operations / Controls
a. Does the grill respond to controls … change modes, turn off, turn on?
b.
c.
5.
If no, is it regarding grill operations/controls?
2 oz. Meat Cooking Issue
a.
3.
Serial Number
Phone Number
City, State
Are you a Taylor Technician?
Is this a meat cooking issue?
a. If yes, go to question #2 for 2 oz. meat or question #3 for 4 oz. meat.
b.
2.
5.
6.
7.
8.
If no:
1.
Go to the back of the grill and pull white switch outward and see how many of the two red lights are
lit. If one or none light up, go to main breaker panel and turn both grill breakers off and then back on.
Check grill and make sure both lights are lit. If both are lit, go to next step. If not, call your local
maintenance person or electrician to find out root cause of power loss at grill.
2.
Do a hard reset by leaving the white switch pulled out and both red lights lit for one full minute (60
seconds). Push the white switch back inward. The two red lights should go out. Restart the grill.
Is grill working properly now?
1.
If yes: the store will be called the next business day to resolve any further points.
2.
If no: an emergency call will be dispatched.
Calls that will receive a follow up the next business day.
a.
Meat quality issues with meat temperatures above 175°F (79°C).
b.
Issues effecting a single platen. (Cook cycle interrupt, platen comes up too fast, platen won't open, etc.)
c.
Requests for grill parts. (Release sheets are ordered with food order and smallwares are ordered from
Kitchen Equipment Supplier - KES.)
C801/C801R/F802/P802/C803/C803R/C804
39
Troubleshooting Guide
Section 8
Warranty Explanation
Parts
Labor
Class 103 Parts
The Taylor warranty is valid only if the required service
work is performed by an authorized Taylor technician.
The warranty for new equipment is one year, with a
replacement parts warranty of three months.
For more details, see the warranty/checkout card.
Contact your local Taylor Distributor regarding
Extended Service Contract options.
Class 000 Parts
Wear items -- no warranty.
Class 212 Parts
The warranty for new equipment parts is two years,
with a replacement parts warranty of 12 months. This
includes the heater/timer boards, lift solenoids, lower
plate heater, and the upper platen assemblies
(aluminum casting and shroud).
Warranty Explanation
40
C801/C801R/F802/P802/C803/C803R/C804
C801/C801R/F802/P802/C803/C803R/C804
070644
070648
070656
071476
072662
070640
070657
X70701-SER
072711
HINGE-PLATE-PLATEN *C801*
PIN-ROLL .250D X 2.500 LONG ZP
PIN-STOP-CAM *C801*
PLATE-OVER CENTER *C801*
PULLEY-PLATEN CABLE
SHAFT-CAM-PLATEN *C801*
SPRING-EXTENSION.500X.063X3.00
SWITCH A.-POSITION *C801*
+HANDLE-LIFT-PLATEN *C801*
41
047922
070739
070740
+NUT-5/8-11 HEX GRADE 5
+SCREW-5/8-11 X 2
+WASHER-5/8 LOCK SS
070728
070658
+SEAL-BEARING-ARM *C801*
BEARING-PILLOW BLOCK 2" SHAFT
017328
071935
BEARING-ARM
+SCREW-3/8-16X3/4 SERRATED HWH
070671-1
071324
+HANDLE-LIFT-PLATEN *C801*
ARM-PLATEN *C801* NON-ADJ
070671
X70670-SER
ARM A.-PLATEN *C801*ADJUSTABE
ARM-PLATEN *C801*
072712-1
ARM-PLATEN *C801* NON-ADJ.
070675
070623
BEARING-CAM *C801*
+SCREW-1/4-20X2 SERRATED H
072712
X73187-SER
ARM A.-PLATEN ADJUSTABLE
ARM-PLATEN *C801*
PART
NUMBER
DESCRIPTION
*
*
*
*
6
12
6
*
*
*
*
2
4
1
2
1
1
4
1
1
4
4
2
1
1
C801
QTY.
*
*
*
*
6
12
6
*
*
*
*
2
4
1
2
1
1
4
1
1
4
4
2
1
1
C801R
QTY.
4
8
4
*
*
*
8
2
2
2
2
8
2
2
8
8
4
1
2
C802
F802
P802
QTY.
QTY.
*
*
*
*
6
12
6
*
*
*
*
2
4
1
2
1
1
4
1
1
4
4
2
1
1
C803
QTY.
*
*
*
*
6
12
6
2
4
1
2
1
1
4
1
1
4
4
2
1
1
C803R
QTY.
4
8
4
*
*
*
8
2
4
2
2
8
2
2
8
4
2
2
2
C804
QTY.
000
000
000
000
000
103
103
103
103
103
103
103
000
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
K6047081 & PRIOR
S/N K8124743 & PRIOR-MUST
USE WITH X70670 ARM ASSYSEE S/B 0162SG
S/N K8124743 & PRIOR-MUST
USE WITH X70670 ARM ASSYSEE S/B 0162SG
S/N K8124743 & PRIOR - MUST
USE WITH 071324 HANDLE
S/N K8124743 & PRIOR - MUST
USE WITH 071324 HANDLE
S/N K8124744 & UP
S/N K8124744 & UP - MUST
USE WITH X73187 ARM - REF
S/B 0162SG
REPLACES 070641 PULLEY
2-3/16 DIA X 063 10/5/07
S/N K8124744 & UP - MUST
USE WITH 072711 HANDLE
REMARKS
Section 9
Parts List
Parts List
Parts List
42
C801/C801R/F802/P802/C803/C803R/C804
070707
070667
070622
072536
070709
072515
070935
070518-SER
070514-SER
BRACKET-RELEASE SHEET *C801*
BRACKET-SEASONING HOLDER *C801
CABLE-ADJUST-PLATEN *C801*
CABLE A.-COMMUNICATION
CLIP-RELEASE SHEET *C801*
COVER-BACKSPLASH *P802*
COVER-PLATEN *C801*
CONTROL-C801 CURRENT MONITOR
CONTROL-C801 MAIN TIMER/HEATER
2
2
3
8
4
1
8
12
2
032567
070519-SER
079800
FILTER-CORCOM 2VR1
SUPPLY-POWER-24VAC IN-DUAL OUT
070718
070719
024156
070741
032567
070519-SER
BLOCK-POWER DIST 3 POLE 8-WIRE
BLOCK-POWER DIST 3POLE 6-WIRE
BLOCK-TERMINAL 7P GREEN
CONTACTOR-60A 3PH 208/240 VAC
FILTER-CORCOM 2VR1
SUPPLY-POWER-24VAC IN-DUAL OUT
CONTROL A.-CONTACTOR *C801R*
X72206-23
070741
CONTACTOR-60A 3PH 208/240 VA
TRANS.-100VA 120/208/240 PRI
2
024156
BLOCK-TERMINAL 7P GREEN
2
2
1
1
070718
BLOCK-POWER DIST 3 POLE 8-WI
1
070719
BLOCK-POWER DIST 3POLE 6-WIR
1
X70743-23
071193
BUSHING-NONPOROUS 3/8IDX5/8OD
4
CONTROL A.-CONTACTOR *C801*
043637
BUSHING-SNAP 1-5/8ID X 2 OD
2
1
039152
BUSHING-SNAP 1-31/32ID - 2-1/2
6
070717
027712
BUSHING-SNAP 1-3/8ID X 1-3/4OD
6
CONTROL-RESET-SWITCH-10A/250
023396
BUSHING-SNAP 15/16 ID X 1-3/32
1
3
*
024156
C801
QTY.
CONTROL-HI-LIMIT 450F NO RES
071320
BLOCK-TERMINAL 7P GREEN
PART
NUMBER
BLOCK-TERMINAL 6 POLE
DESCRIPTION
2
2
2
1
1
1
1
1
*
2
2
3
8
4
1
8
12
4
2
6
6
1
3
C801R
QTY.
1
*
2
2
2
6
8
6
8
2
1
9
6
1
2
1
*
2
2
1
1
3
1
6
6
C802
F802
P802
QTY.
QTY.
1
*
2
2
3
8
4
1
8
12
4
2
6
6
1
3
C803
QTY.
1
*
2
2
3
8
4
1
8
12
5
2
6
6
1
3
C803R
QTY.
1
*
2
2
2
6
8
1
6
8
2
1
12
9
1
2
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
212
103
103
103
000
103
103
103
103
103
000
000
000
103
103
103
WARR.
CLASS
208V 60HZ 3PH & 240V 60HZ
3PH
SEE - KIT A.-CONTROL-HI
LIMIT X71752-SER
REMARKS
C801/C801R/F802/P802/C803/C803R/C804
43
Parts List
024156
070741
070717
072075
072076
071738
070880-27
BLOCK-TERMINAL 7P GREEN
CONTACTOR-60A 3PH 208/240 VAC
CONTROL-RESET-SWITCH-10A/250
HARNESS-RESET SWITCH "A"*C803
HARNESS-RESET SWITCH "B"*C803
JUMPER A.-CONTACTOR COIL*C803
LIGHT-RED-230V
024156
070741
070717
072075
072076
071738
070880-27
BLOCK-TERMINAL 7P GREEN
CONTACTOR-60A 3PH 208/240 VAC
CONTROL-RESET-SWITCH-10A/250
HARNESS-RESET SWITCH "A"*C803"
HARNESS-RESET SWITCH "B"*C803"
JUMPER A.-CONTACTOR COIL*C801*
LIGHT-RED-230V
070741
071738
CONTACTOR-60A 3PH 208/240 VAC
JUMPER A.-CONTACTOR COIL*C80
071153
071488-23
DIAGRAM-WIRING *C801*
071738
JUMPER A.-CONTACTOR COIL*C803
DAMPER-OIL FILLED-4.5 STROKE
073091
CONTACTOR-75A 3PH 208/240 VAC
072330
024156
BLOCK-TERMINAL 7P GREEN
CORD A.-POWER-250V-4 WIRE
070718
BLOCK-POWER DIST 3 POLE 8-WIRE
X73054-23
024156
BLOCK-TERMINAL 7P GREEN
CONTROL A.-CONTRACTOR *C804*
070718
BLOCK-POWER DIST 3 POLE 8-WIRE
X71783-23
070719
BLOCK-POWER DIST 3POLE 6-WIRE
CONTROL A.-CONTRACTOR *F802*
070718
BLOCK-POWER DIST 3 POLE 8-WIRE
X73210-23
070719
BLOCK-POWER DIST 3POLE 6-WIRE
CONTROL A.-CONTRACTOR *C803R*
070718
X72046-23
079800
PART
NUMBER
BLOCK-POWER DIST 3 POLE 8-WIRE
CONTROL A.-CONTRACTOR *C803*
TRANS.-100VA 120/208/240 PRI
DESCRIPTION
1
3
C801
QTY.
3
2
C801R
QTY.
2
1
1
1
1
1
1
C802
F802
P802
QTY.
QTY.
3
2
2
1
1
1
2
1
1
1
1
C803
QTY.
3
2
2
1
1
1
2
1
1
1
1
C803R
QTY.
2
1
1
1
1
1
1
C804
QTY.
000
103
103
103
103
103
103
103
000
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
208V 60HZ 3PH
K5012546 & UP
REMARKS
Parts List
44
C801/C801R/F802/P802/C803/C803R/C804
072201
072202
071364
072251
072683
072688
073134
HARNESS A.-PLATEN CRU *C803*
HARNESS A.-PLATEN CMU *C803*
HARNESS-CAN BUS *C801*
HARNESS-CAN BUS *C801R*
HARNESS-CAN BUS *F802*
HARNESS-CAN BUS *P802*
HARNESS-CAN BUS *C804*
071324
HANDLE-LIFT-PLATEN *C801*
072250
072711
HANDLE-LIFT-PLATEN *C801*
HARNESS A.-PLATEN-CMU *C801R
070647
HANDLE-ADJUST-PLATEN*C801*
071633
064274
GUIDE-TROUBLESHOOT-WENDY'S
HARNESS A.-PLATEN-CMU *C801*
070943
GASKET-PLATEN COVER *C801* UPP
071632
070748
GASKET-CONTROL *C801*
HARNESS A.-PLATEN-CRU *C801*
070747
GASKET-CONTROL *C801*
071631
071665
FUSE-3A 32VDC MINI-BLADE
HARNESS A.-PLATEN-CLU *C801*
071664
FUSE-2A 32VDC MINI-BLADE
071863
070848
DIVIDER A.-3 LANE *C801* STAGE
HARNESS-12 VDC *P802*
070851
DIVIDER A.-*C801* COOK
071842
070847
DIVIDER A.-*C801* 2 LANE
HARNESS-12VDC *F802
073137-23
DIAGRAM-WIRING *C804*
072081
071860-23
DIAGRAM-WIRING *P802* V1-1-1
070867
072333-23
DIAGRAM-WIRING *F802* STD
HARNESS-12VDC *C803*
072159-23
HARNESS-12VDC *C801*
072260-23
DIAGRAM-WIRING *C803*
PART
NUMBER
DIAGRAM-WIRING *C801R*
DESCRIPTION
1
1
1
1
1
*
3
1
1
3
2
2
2
6
1
1
1
C801
QTY.
1
1
1
1
1
*
3
1
1
3
2
2
2
6
1
1
1
1
C801R
QTY.
1
1
1
1
2
2
2
2
6
1
1
1
1
1
1
3
1
1
C802
F802
P802
QTY.
QTY.
1
1
1
1
*
3
1
1
3
2
6
1
1
1
1
C803
QTY.
1
1
1
1
3
1
1
3
2
6
1
1
1
1
C803R
QTY.
1
1
1
1
*
2
2
2
2
6
1
2
1
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
000
000
000
000
000
000
103
103
103
000
000
000
000
000
WARR.
CLASS
S/N K8124743 & PRIOR-MUST
USE WITH X70670 ARM ASSYSEE S/B 0162SG
S/N K8124744 & UP - MUST
USE WITH X73187 ARM
208V 60HZ 3PH
208V 60HZ 3PH
208V 60HZ 3PH
208V 60HZ 3PH
208V 60HZ 3PH
REMARKS
C801/C801R/F802/P802/C803/C803R/C804
45
Parts List
071495
071496
071497
071864
071865
072079
072080
072082
072083
070858
071614
071613
071612
072199
072200
072198
072197
071868
071869
070803
070865
073177
073178
071363
072682
HARNESS-FEED A-L1 MAIN IN
HARNESS-FEED A-L2/L3 MAIN IN
HARNESS-FEED B-L3 MAIN IN
HARNESS-FEED L1 MAIN IN
HARNESS-FEED B-L2/L3 MAIN IN
HARNESS-FEED A-L2/L3 MAIN IN
HARNESS-FEED B-L3 MAIN IN
HARNESS-FEED A-L1 MAIN IN
HARNESS-FEED B-L1/L2 MAIN IN
HARNESS-FILTER *C801*
HARNESS-HIGH LIMIT *C801*CLL
HARNESS-HIGH LIMIT *C801*CML
HARNESS-HIGH LIMIT *C801*CRL
HARNESS-HIGH LIMIT *C803*CLL
HARNESS-HIGH LIMIT *C803*CLU
HARNESS-HIGH LIMIT *C803*CML
HARNESS-HIGH LIMIT *C803*CRL
HARNESS-HIGH LIMIT *P802*
HARNESS-HIGH LIMIT *P802*L
HARNESS-MODE 1/0-LG *C801*
HARNESS-MODE I/0-SHT *C801*
HARNESS-MODE I/0-LG
HARNESS-MODE I/0-SHT
HARNESS-NODE *C801*
HARNESS-NODE *F802*
073154
071494
HARNESS-FEED B-L1/L2 MAIN IN
HARNESS-NODE *C804*
071850
HARNESS-CURRENT SENSE-MC0
072686
071849
HARNESS-CURRENT SENSE-MC1
HARNESS-NODE-LEFT *P802*
072077
HARNESS-CURRENT SENSE-MCI
072685
070844
HARNESS-NODE-RIGHT *P802*
070795
HARNESS-CURRENT SENSE-MCO
PART
NUMBER
HARNESS-CURRENT SENSE-MC1
DESCRIPTION
4
1
1
1
1
1
2
1
1
1
1
1
1
C801
QTY.
4
1
1
1
1
1
2
1
1
1
1
1
1
C801R
QTY.
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
C802
F802
P802
QTY.
QTY.
3
1
1
1
1
1
1
2
1
1
1
1
1
1
C803
QTY.
3
1
1
1
1
1
1
2
1
1
1
1
1
1
C803R
QTY.
3
1
1
1
1
1
2
1
1
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
REMARKS
Parts List
46
C801/C801R/F802/P802/C803/C803R/C804
071866
072078
072376
072377
073136
073135
071492
072320
071493
072321
073243
073244
071736
071737
071853
072075
072076
072361
071852
071627
072177
072203
072362
071630
072319
071851
071867
073139
071362
071840
072383
072384
072749
072750
HARNESS-RELAY LOW VOLTAGE MCO
HARNESS-RELAY-LOW VOLTAGE -MC1
HARNESS-RELAY-LOW VOLTAGE -MCI
HARNESS-RELAY-LOW VOLTAGE-MC
HARNESS-RELAY-LOW VOLTAGE-MC
HARNESS-RELAY-LOW VOLTAGE-MC1
HARNESS-RELAY-LOW VOLTAGE-MC1
HARNESS-RELAY-LOW VOLTAGE-MCO
HARNESS-RELAY-LOW VOLTAGE-MCO
HARNESS-RELAY-LOW VOLTAGE-MC1
HARNESS-RELAY-LOW VOLTAGE-MC0
HARNESS-RESET SWITCH "A"*C801*
HARNESS-RESET SWITCH "B"*C801*
HARNESS-RESET SWITCH *F802*
HARNESS-RESET SWITCH "A"*C803*
HARNESS-RESET SWITCH "B"*C803*
HARNESS-SOLENOID MAIN IN
HARNESS-SOLENOID *F802*
HARNESS-SOLENOID *C801*
HARNESS-SPEAKER *C801* 2 PLUG
HARNESS-SPEAKER *C803*2 PLUG
HARNESS-SPEAKER*P802*2 PLUG
HARNESS-STAGE-HIGH LIMIT*C801*
HARNESS-STAGE-HIGH LIMIT*C801R
HARNESS-STAGE-HIGH LIMIT*F802*
HARNESS-STAGE HIGH LIMIT*P802*
HARNESS-STAGE R-HIGH LIM*C804*
HARNESS-T.C. JUMPER *C801*
HARNESS-T.C. JUMPER *F802 MCO
HARNESS-T.C.JUMPER *F802* MC
HARNESS-T.C.JUMPER *F802* MC
HARNESS-TRANSFORMER-L1 *F802*
HARNESS-TRANSFORMER-L3 *F802*
PART
NUMBER
HARNESS-RELAY LOW VOLTAGE
DESCRIPTION
1
1
1
1
1
1
1
1
C801
QTY.
1
1
1
1
1
1
1
1
C801R
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C802
F802
P802
QTY.
QTY.
1
1
1
1
1
1
1
1
C803
QTY.
1
1
1
1
1
1
1
1
C803R
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
REMARKS
C801/C801R/F802/P802/C803/C803R/C804
47
Parts List
+SCREW-8-32X1/4 PHILLIPS
070746
LENS-CONTROL *C801*
X72135
KIT A.-NODE-FRONT C801 W/HARN
071663
071459
LENS-NODE-REAR STAGE *C801*
LIFTER A.-ARM *C801*
071363
070908
GASKET-NODE *C801*
HARNESS-NODE *C801*
070951-SER
X72136
CONTROL-C801 STAGE NODE W/LED
KIT A.-NODE-REAR C801 W/HARN
071457
071460
LENS-NODE *C801*MODE I/0
LENS-NODE-FRONT*C801*STAGE
071458
LENS-NODE *C801* COOK
071363
070865
HARNESS-MODE I/O-SHRT *C801*
HARNESS-NODE *C801*
070803
HARNESS-MODE I/0-LG *C801*
070908
071363
HARNESS-NODE *C801*
GASKET-NODE *C801*
070908
GASKET-NODE *C801*
070951-SER
071242-SER
CONTROL-C801 MODE I/O
CONTROL-C801 STAGE NODE W/LED
071180-SER
CONTROL-GRILL COOK SIDE
6
8
2
8
2
1
8
3
8
2
1
1
3
1
1
3
4
1
3
6
8
1
8
2
1
1
X72134
070746
KIT A.-NODE-COOK C801 W/HARN
LENS-CONTROL *C801*
2
070748
GASKET-CONTROL *C801*
2
1
070747
1
1
2
2
80
80
20
2
3
C801R
QTY.
GASKET-CONTROL *C801*
X77235-SER
070748
GASKET-CONTROL *C801*
KIT A.-PLATE A.-DEC-REAR*C801R
070747
1
80
X70630-SER
GASKET-CONTROL *C801*
KIT A.-PLATE A.-DEC-REAR*C801*
20
071700
X71752-SER
KIT A.-CONTROL-HI-LIMIT 450F
80
072212-23
HEATER-CAST 208V-2400 WATTS
2
3
C801
QTY.
007543
070665-23
+WASHER-#8 INTERNAL TOOTH LOC
070634-23
HEATER-CAST 208V-2400 WATTS
PART
NUMBER
HEATER-CAST 208V-4350 WATTS
DESCRIPTION
4
52
52
13
1
2
28
28
7
1
2
C802
F802
P802
QTY.
QTY.
6
8
3
8
2
1
80
80
20
2
3
C803
QTY.
80
80
20
2
3
C803R
QTY.
4
56
56
14
2
2
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
000
000
103
103
000
000
103
000
000
103
212
212
212
WARR.
CLASS
KIT A.-CONTROL-HI-LIMIT
PLATE LOW-STAGE SIDE
PLATE LOW-COOK SIDE
REMARKS
Parts List
48
C801/C801R/F802/P802/C803/C803R/C804
071242-SER
070908
070803
070865
072682
071461
CONTROL-C801 MODEL I/O
GASKET-NODE *C801*
HARNESS-MODE I/0-LG *C801*
HARNESS-MODE I/O-SHRT *C801*
HARNESS-NODE-COMPLETE *F802*
LENS-NODE-FRONT STAGE *C802*
070951-SER
071180-SER
071242-SER
070908
070803
070865
CONTROL-C801 STAGE NODE W/LED
CONTROL-GRILL COOK NODE
CONTROL-C801 MODEL I/O
GASKET-NODE *C801*
HARNESS-MODE I/0-LG *C801*
HARNESS-MODE I/O-SHRT *C801*
X71593-SER
071180-SER
CONTROL-GRILL COOK NODE
NODE A.-COMPLETE *P802*
070951-SER
CONTROL-C801 STAGE NODE W/LE
X71550-SER
X71201
NODE A.-COMPLETE-STAGE-REAR
NODE A.-COMPLETE *F802*
X71198
071265
TURNBUCKLE *C801*
NODE A.-COMPLETE-STAGE-FRONT
070654-23
SOLENOID-PLATEN LIFT *C801*
X71166
071154
SHAFT-PLATEN LINKAGE *C801*
NODE A.-COMPLETE *C801* COOK
071477
PULLEY-SHIELDED BEARING
072493-M
071266
LINKAGE-PIVOT-LOWER *C801*
MAN-OPER 801REVERSE/C802
070752
BLOCK-LINKAGE STOP *C801*
071261-M
071262
BEARING-SELF ALIGN-TIE ROD
MAN-OPER C801
070805
X71276-SER
BEARING-OPEN END NEEDLE-5/8
070880-27
LINKAGE A. *C801*
PART
NUMBER
LIGHT-RED-230V
DESCRIPTION
1
1
1
1
3
3
6
12
3
12
3
9
3
2
C801
QTY.
1
1
3
3
6
12
3
12
3
9
3
2
C801R
QTY.
4
1
1
1
7
1
2
1
1
1
2
2
4
8
2
8
2
6
2
1
1
1
8
1
3
1
1
C802
F802
P802
QTY.
QTY.
1
1
3
3
6
4
3
12
3
9
3
2
C803
QTY.
C803R
QTY.
1
2
2
4
8
2
4
2
6
2
1
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
000
000
103
112
103
103
103
103
103
103
103
103
WARR.
CLASS
USE KIT A.-NODE-REAR C801
W/HARN - X72136
USE KIT A.-NODE-FRONT C801
W/HARN X72135
USE KIT A.-NODE-COOK
X72134
WARRANTY CHANGED FROM
212 K5114439
REMARKS
C801/C801R/F802/P802/C803/C803R/C804
49
Parts List
070908
070803
070865
HARNESS-MODE I/0-LG *C801*
HARNESS-MODE I/O-SHRT *C801*
071242-SER
CONTROL-C801 MODEL I/O
GASKET-NODE *C801*
071180-SER
X72062
CONTROL-GRILL COOK NODE
NODE A.-COMPLETE *C803* COOK
071461
X72243
NODE A.-COMPLETE *C801R*STG F
LENS-NODE-FRONT STAGE *C802*
071460
LENS-NODE *C801*MODE I/0
071363
071458
LENS-NODE *C801* COOK
HARNESS-NODE *C801*
071363
HARNESS-NODE *C801*
070908
070865
HARNESS-MODE I/O-SHRT *C801
GASKET-NODE *C801*
070803
HARNESS-MODE I/0-LG *C801*
070951-SER
070908
GASKET-NODE *C801*
CONTROL-C801 STAGE NODE W/LED
071242-SER
X72254
CONTROL-C801 MODEL I/O
071460
LENS-NODE *C801*MODE I/0
NODE A.-COMPLETE *C801R* COOK
8
1
8
2
1
1
3
2
1
1
4
1
3
071458
LENS-NODE *C801* COOK
071180-SER
071363
HARNESS-NODE *C801*
CONTROL-GRILL COOK NODE
1
070865
HARNESS-MODE I/O-SHRT *C801*
1
3
070803
HARNESS-MODE I/0-LG *C801*
1
1
4
1
3
1
2
1
1
4
1
3
1
070908
X72062
NODE A.-COMPLETE *C803* COOK
1
GASKET-NODE *C801*
071460
LENS-NODE *C801*MODE I/0
3
C803
QTY.
071242 -SER
071458
LENS-NODE *C801* COOK
4
1
1
C802
F802
P802
QTY.
QTY.
CONTROL-C801 MODEL I/O
071457
LENS-NODE-FRONT*C801*STAGE
C801R
QTY.
071180-SER
072686
C801
QTY.
CONTROL-GRILL COOK NODE
072685
HARNESS-NODE-LEFT *P802*
PART
NUMBER
HARNESS-NODE-RIGHT *P802*
DESCRIPTION
8
1
8
2
1
1
3
2
1
1
4
1
3
1
C803R
QTY.
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
REMARKS
Parts List
50
C801/C801R/F802/P802/C803/C803R/C804
071242-SER
070908
CONTROL-C801 MODEL I/O
GASKET-NODE *C801*
071242-SER
070908
070803
070865
072682
071458
071460
071461
CONTROL-C801 MODEL I/O
GASKET-NODE *C801*
HARNESS-MODE I/0-LG *C801*
HARNESS-MODE I/O-SHRT *C801*
HARNESS-NODE-COMPLETE *F802*
LENS-NODE *C801* COOK
LENS-NODE *C801*MODE I/0
LENS-NODE-FRONT STAGE *C802*
071242-SER
070908
071363
073154
073177
073178
071457
071458
071460
CONTROL-C801 MODE I/O
GASKET-NODE *C801*
HARNESS-NODE *C801*
HARNESS-NODE *C804*
HARNESS-MODE I/0-LG
HARNESS-MODE I/0-SHT
LENS-NODE-FRONT*C801*STAGE
LENS-NODE *C801* COOK
LENS-NODE *C801*MODE I/0
070951-SER
070908
071363
071461
CONTROL-C801 STAGE NODE W/LED
GASKET-NODE *C801*
HARNESS-NODE *C801*
LENS-NODE-FRONT STAGE *C802*
X73063
071180-SER
CONTROL-GRILL COOK SIDE
NODE A.-COMPLETE *C804*
070951-SER
CONTROL-C801 STAGE NODE W/LED
X73057
071180-SER
CONTROL-GRILL COOK NODE
NODE A.-COMPLETE *C804*
070951-SER
CONTROL-C801 STAGE NODE W/LED
X71550-SER
071180-SER
CONTROL-GRILL COOK NODE
NODE A.-COMPLETE *F802*
070951-SER
X71593-SER
071363
PART
NUMBER
CONTROL-C801 STAGE NODE W/LED
NODE A.-COMPLETE *P802*
HARNESS-NODE *C801*
DESCRIPTION
C801
QTY.
C801R
QTY.
4
1
2
1
1
1
7
1
2
1
1
8
1
3
1
1
C802
F802
P802
QTY.
QTY.
2
C803
QTY.
C803R
QTY.
4
1
4
1
1
1
2
4
1
1
2
1
7
1
2
1
1
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
REMARKS
C801/C801R/F802/P802/C803/C803R/C804
51
Parts List
X72272
X71775
X73071
X72278
X72059
X73204
X73069
X73180
071137
071536
X71307
X71305
X72240
X72241
072060
X71779
X71778
070607
070635
072065
072066
073206
073207
071527
071528
PANEL A.-BACKSPLASH *F802*L
PANEL A.-BACKSPLASH *P802*
PANEL A.-BACKSPLASH *C804*
PANEL A.-REAR *F802* STAGE
PANEL A.-REAR *C803* STAGE
PANEL A.-REAR *C803R* STAGE
PANEL A.-REAR *C804* STAGE
PANEL A.-REAR *C804* STAGE
PANEL-REAR-COOK *C801*
PANEL-REAR *F802*
PANEL A.-SERVICE *C801* COOK
PANEL A.-SERVICE *C801* STAGE
PANEL A.-SERVICE *C801R* COOK
PANEL A.-SERVICE *C801R* STAGE
PANEL-SERVICE *C803*
PANEL A.-SIDE-LEFT *P802*
PANEL A.-SIDE-RIGHT *P802*
PANEL-SIDE *C801* LEFT
PANEL-SIDE *C801* STAGING
PANEL-SIDE *C803* LEFT
PANEL-SIDE *C803* RIGHT
PANEL-SIDE *C803R* RIGHT
PANEL-SIDE *C803R* LEFT
PANEL-SIDE *F802* LEFT
PANEL-SIDE *F802* RIGHT
X70781
X72452
PANEL A.-BACKSPLASH *F802*
COVER A.-SPEAKER *C801*
X72070
PANEL A.-BACKSPLASH-R. *C803
X70783
X72244
PANEL A.-BACKSPLASH *C801R* R
PANEL A.-SPLASH SHLD W/SPEAK
X72248
PANEL A.-BACKSPLASH *C801R* L
073075
X71135
PANEL-SIDE *C804* RIGHT
X71136
PANEL A.-BACKSPLASH-L *C801*
PART
NUMBER
PANEL A.-BACKSPLACH-R
DESCRIPTION
1
1
1
1
1
1
1
1
*
C801
QTY.
1
1
1
1
1
1
*
C801R
QTY.
1
1
1
1
1
1
1
C802
F802
P802
QTY.
QTY.
1
1
2
1
1
1
1
C803
QTY.
1
1
2
1
1
1
1
C803R
QTY.
1
1
1
1
1
1
1
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
S/N K6076002 & PRIOR
S/N K6076002 & PRIOR
USED K5061317 & PRIOR
USED K5061317 & PRIOR
REMARKS
Parts List
52
C801/C801R/F802/P802/C803/C803R/C804
X72509
072451
073072
X71325
X71565
071798
071799
071859
072521
071310
071984
071985
073073
X71246
X70630
X72235
X72237
X72000
X72053
X73221
X72761
071249
072234
072055
072054
PANEL-SPLASH-SHIELD-END *F802*
PANEL-SPLASH-SHIELD-END *C804*
PANEL A.-WIRE SHIELDING *C801
PANEL A.-WIRE SHIELDING *F8
PANEL-BOTTOM RIGHT *P802*
PANEL-BOTTOM LEFT *P802*
PANEL-DIVIDER MID *F802*
PANEL-DIVIDER MID *P802*
PANEL-HEATER *C801*
PANEL-HEATER *C802* COOK
PANEL-HEATER *C802* STAGE
PANEL-HEATER *C804* STAGE
PLATE A.-DEC *C801*
PLATE A.-DEC-REAR *C801*
PLATE A.-DEC-REAR *C801R*
PLATE A.-DEC *C801R* STAGE
PLATE A.-DEC *F802*
PANEL A.-DEC *C803*
PANEL A.-DEC *C803R*
PLATE A.-DEC *P802*
PLATE-DEC *C801* COOK
PLATE-DEC *C801R* COOK
PLATE-DEC *C803* COOK
PLATE-DEC *C803* STAGE
072175
SPEAKER-MICRO*MYLAR CONE
PANEL A.-SPLASH-L *P802*
071118
SHIELD-GREASE-SPEAKER *C801*
X72508
072177
HARNESS-SPEAKER *C801* 2 PLU
PANEL A.-SPLASH-R *P802*
X72252
COVER A.-SPEAKER *C801R*
072175
SPEAKER-MICRO*MYLAR CONE
X72247
071118
PANEL A.-SPLASH SHLD W/SPEAK
072177
SHIELD-GREASE-SPEAKER *C801*
PART
NUMBER
HARNESS-SPEAKER *C801* 2 PLU
DESCRIPTION
1
*
1
2
1
1
1
1
C801
QTY.
1
1
1
2
1
1
1
1
1
1
C801R
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C802
F802
P802
QTY.
QTY.
1
1
1
2
1
C803
QTY.
1
2
1
C803R
QTY.
1
1
1
1
1
1
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
USE X72235-SER KIT
USE X70630-SER KIT
S/N K6076003 & UP
S/N K6076003 & UP
REMARKS
C801/C801R/F802/P802/C803/C803R/C804
53
Parts List
070940
X71823-23
PLATE-SEAL *C801* REAR
PLATEN A.-SERVICE *C801* 2 OZ
072266
X71337
070856
PIN-GUIDE-PLATEN *C801
SHROUD A.-PLATEN *C801* 4 OZ
THERMOCOUPLE-PLATEN
072266
X71339
070856
PIN-GUIDE-PLATEN *C801
SHROUD A.-PLATEN *C801* ADJ
THERMOCOUPLE-PLATEN
074972-60
072266
X71339
PIN-GUIDE-PLATEN *C801
SHROUD A.-PLATEN *C801* ADJ
X71752-SER
GASKET-GORE-TEX .250 DIA
CONTROL-HI-LIMIT 450F NO RESET
X72669-23
074972-60
GASKET-GORE-TEX .250 DIA
PLATEN A.-SERVICE ADJ LEFT
X71752-SER
CONTROL-LIMIT MANUAL RESET 450
X71825-23
074972-60
GASKET-GORE-TEX .250 DIA
PLATEN A.-SERVICE *C801* ADJ
X71752-SER
X71824-23
CONTROL-LIMIT MANUAL RESET 450
PLATEN A.-SERVICE *C801* 4 OZ
070856
071360
PLATE-SEAL *C801* REAR
X71338
070941
PLATE-SEAL *C801* LOWER REAR
THERMOCOUPLE-PLATEN
070934
PLATE-SEAL *C801* FRONT
SHROUD A.-PLATEN *C801* 2 OZ
X70939
PLATE A.-SEAL *C801* REAR OUT
071120
073068
PLATE-DEC *C804*
074972-60
073062
PLATE-DEC *C804*
PIN-GUIDE-PLATEN *C801
071772
PLATE-DEC *P802*
GASKET-GORE-TEX .250 DIA
072236
PLATE-DEC-REAR *C801R*
X71752-SER
073208
CONTROL-LIMIT MANUAL RESET 450
073209
PLATE-DEC *C803R* COOK
PART
NUMBER
PLATE-DEC *C803R* STAGE
DESCRIPTION
3
1
1
1
3
1
3
1
4
1
3
1
3
1
4
1
3
1
3
3
3
3
3
C801
QTY.
3
1
1
1
3
1
3
1
4
1
3
1
3
1
4
1
3
1
3
3
3
3
C801R
QTY.
1
4
1
3
1
3
1
4
1
3
1
2
2
2
2
1
1
C802
F802
P802
QTY.
QTY.
3
1
1
1
3
1
3
1
4
1
3
1
3
1
4
1
3
1
3
3
3
3
3
C803
QTY.
3
1
1
1
3
1
3
1
4
1
3
1
3
1
4
1
3
1
3
3
3
3
3
1
1
C803R
QTY.
1
4
1
3
1
3
1
1
1
3
1
2
2
2
2
2
1
1
C804
QTY.
103
103
000
103
212
103
103
103
000
103
212
103
103
103
000
103
212
103
103
103
000
103
212
103
103
103
103
103
103
103
103
103
WARR.
CLASS
R700032
USE KIT A.-CONTROL-HI-LIMIT
R700032
USE KIT A.-CONTROL-HI-LIMIT
REMARKS
Parts List
54
C801/C801R/F802/P802/C803/C803R/C804
070701
070855
070856
THERMOCOUPLE-LOWER HEATERS
THERMOCOUPLE-PLATEN
071118
+SHIELD-GREASE-SPEAKER *C801*
SWITCH-POSITION-PLATEN
072362
+HARNESS-SPEAKER*P802*2 PLUG
071186
072203
+HARNESS-SPEAKER *C803*2 PLUG
071185
072177
+HARNESS-SPEAKER *C801* 2 PLUG
STUD-MOUNTING PLATE *C801* L
X72252
+COVER A.-SPEAKER *C801R*
STUD-MOUNTING PLATE *C801* S
X70781
+COVER A.-SPEAKER *C801*
071227
072175
SPEAKER-MICRO *C801*MYLAR CO
070854
X71284
SHIELD A.-LOCATING BUCKET
STUD-HEATER *C801*
071732
SHIELD-BACKSPLASH *F802*
SPRING-EXTENSION-LATCH
070765
SHIELD-BACKSPLASH *C801*
070619
X70944
SHELF A.-MEAT LOADING *C801*
071475
070708
SHEET-RELEASE *C801*
SPRING-EXTENSION.982X.118X11.3
070936
SEAL-PLATEN-REAR *C801*
SPRING-EXTENSION 1.062 X .128
070937
SEAL-PLATEN-FRONT *C801*
072013
070658
SEAL-BEARING-ARM *C801*
SPEAKER-C801-SOLDER POSTS
071482
070685
+SPACER-SELF RETAINING *C801*
ROD-SPRING-OPEN *C801*
062569
074210-02
070856
PART
NUMBER
+SCREW-6-32X7/8 PHILLIPS ROUND
RELAY-SS 25A NON-ALARM 240 VAC
THERMOCOUPLE-PLATEN
DESCRIPTION
9
11
5
4
12
50
6
12
3
*
1
1
1
1
1
1
1
12
3
4
6
3
24
24
23
C801
QTY.
9
11
5
4
12
50
6
12
1
1
1
1
1
1
1
12
3
4
6
3
24
24
23
C801R
QTY.
6
7
6
8
30
4
4
1
1
1
1
12
2
4
4
2
15
15
15
3
7
8
30
1
1
1
7
7
7
C802
F802
P802
QTY.
QTY.
9
11
5
4
12
50
6
12
3
1
1
1
1
1
12
3
4
6
3
24
24
23
C803
QTY.
9
11
5
4
12
50
6
12
1
1
1
1
1
12
3
4
6
3
24
24
23
C803R
QTY.
6
8
6
12
40
4
4
6
1
1
1
1
1
12
2
4
4
2
16
16
16
3
C804
QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
000
103
000
000
000
103
000
000
103
103
WARR.
CLASS
PLATE LOW-COOK SIDE-SEE
PLATEN
PLATE LOW-COOK SIDE
PLATE LOW-COOK SIDE
PLATE LOW-COOK SIDE
K5033845 & UP
S/N K6108576 & PRIOR REPLACES 070694
S/N K6124876 & UP REPLACES 072013 & 070694
COLUMBUS MRKT-SYGMA
REMARKS
C801/C801R/F802/P802/C803/C803R/C804
55
Parts List
071488-28
072260-28
072159-28
071559-28
071860-28
070865
072179
072180
070634-28
072212-28
X71823-28
X71824-28
X71825-28
X72669-23
DIAGRAM-WIRING *C801R*
DIAGRAM-WIRING *C803*
DIAGRAM-WIRING *F802* V1-
DIAGRAM-WIRING *P802* 204
HARNESS-MODE I/O-SHRT *C8
JUMPER A.-240 VOLT *C801*
LABEL-240 VOLT
HEATER-CAST 240V-4350 WATTS
HEATER-CAST 240V-2400 WATTS
PLATEN A.-SERVICE *C801* 2 OZ
PLATEN A.-SERVICE *C801* 4 OZ
PLATEN A.-SERVICE *C801* ADJ
PLATEN A.-SERVICE ADJ LEFT
PART
NUMBER
DIAGRAM-WIRING *C801*
240V 60HZ 3PH
DESCRIPTION
1
1
1
2
3
2
2
1
1
C801
QTY.
1
1
1
2
3
2
2
1
1
C801R
QTY.
1
1
1
2
1
2
1
1
1
2
1
1
1
1
C802
F802
P802
QTY.
QTY.
1
1
1
2
3
1
2
1
1
C803
QTY.
C803R
QTY.
C804
QTY.
212
212
212
212
212
212
000
000
103
000
000
000
000
000
WARR.
CLASS
REMARKS
Model C801
071488-23
5/09
Model C801
071488-28
5/09
Model C801R
072260-23
5/09
Model C801R
072260-28
5/09
Model F802
072333-23
5/09
Model F802
071559-28
5/09
Model P802
071860-23
5/09
Model P802
071860-28
5/09
Models C803/C803R
072159-23
5/09
Model C803
072159-28
5/09
Model C804
073137-23
5/09