A7 A6 A8
A
A3
A4
A5
A10
A18
A2
A1
A14
A13
A19
A12
A15
A16
A17
A20
A21
A22
A23
A9
A11
B
B10
B11
B12
B6
B1
B4
B7
B8
B9
B5
B2
B3
3
2
1
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
21
22
23
24
25
26
27
28
29
30
5
Instructions
COFFEE AND CAPPUCCINO MAKER
CONTENTS
IT
INTRODUCTION ...........................................7
GB
FR
Français
DE
Deutsch
PT
Português
IL
MCX103X
GB
IT
English
Italiano
NL
Nederlands
GR
Ελληνικά
ES
Espãnol
RU
Русский
Symbols used in these instructions .......................................7
Letters in brackets .................................................................7
Troubleshooting and repairs ..................................................7
SAFETY ....................................................7
Avvertenze fondamentali per la sicurezza ...............................7
Designated use .......................................................................7
Instructions ............................................................................7
Child safety.............................................................................8
DESCRIPTION .............................................8
Description of the appliance .................................................8
Description of the control panel..............................................8
PRELIMINARY CHECKS..................................8
Controls after transport .........................................................8
Installing the appliance ...........................................................8
Connecting the appliance........................................................8
DISPOSAL .................................................8
BUILT-IN INSTALLATION ................................9
USING THE APPLIANCE FOR THE FIRST TIME ....11
TURNING ON AND HEATING UP ......................11
MAKING COFFEE USING COFFEE BEANS ..............11
CHANGING THE QUANTITY OF COFFEE IN THE CUP
.............................................................12
ADJUSTING THE COFFEE MILL ......................12
MAKING ESPRESSO COFFEE WITH PRE-GROUND
COFFEE (INSTEAD OF BEANS) .........................12
DELIVERING HOT WATER..............................12
MAKING CAPPUCCINO (USING THE STEAM
FUNCTION) ..............................................13
CLEANING ...............................................13
Cleaning the coffee maker ...................................................13
Cleaning the grounds container ............................................13
Cleaning the drip tray............................................................13
Cleaning the water tank .......................................................13
Cleaning the spouts .............................................................13
Cleaning the pre-ground coffee funnel..................................13
Cleaning the inside of the coffee maker ................................14
Cleaning the brewing unit ....................................................14
CHANGING AND SETTING MENU PARAMETERS ...14
Rinsing .................................................................................14
Setting the clock ..................................................................14
Setting the language ............................................................15
Setting auto-start time .........................................................15
Descale .................................................................................15
Changing coffee temperature................................................15
Changing the length of time the appliance remains on ........15
Setting water hardness ........................................................15
Resetting default values (reset) ...........................................16
Statistics ..............................................................................16
6
Buzzer ..................................................................................16
TURNING THE APPLIANCE OFF .........................16
TECHNICAL SPECIFICATION...........................16
DISPLAYED MESSAGES ...............................17
TROUBLESHOOTING....................................18
INTRODUCTION
Symbols used in these instructions
Important warnings are identified by these symbols.
Failure to observe the instructions could result in electric shock, serious injury, burns, fire or damage to the appliance.
Danger!
Failure to observe the warning could result in possibly life threatening injury from electric shock.
Important!
Failure to observe the warning could result in injury or damage to
the appliance.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
N.B.!
Important information for the user
Letters in brackets
The letters in brackets refer to the legend in the Description of the
Appliance on page 3.
Troubleshooting and repairs
In the event of problems, follow the information given in the sections
"Displayed messages" and "Troubleshooting".
If this does not resolve the problem, you should consult Customer
Services.
For repairs, contact Customer Services only.
SAFETY
Fundamental safety warnings
Important! This is an household appliance only.
•
•
Make sure the socket used is freely accessible at all times, enabling the appliance to be unplugged when necessary.
If the appliance is faulty, do not attempt to repair.
Turn it off using the main switch (A23), unplug from the mains
socket and contact Customer Services.
Important! Keep all packaging (plastic bags, polystyrene
foam) away from children.
Important! The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure they do not play with the appliance.
Danger of burns! This appliance produces hot water and
steam may form while it is in operation.
Avoid contact with splashes of water or hot steam.
Use knobs and handles.
Important! Do not grasp the coffee maker when it is out of
the cabinet. Do not rest recipients containing liquids or inflammable or corrosive materials on top of the appliance. Place the accessories required to make the coffee (the measure for example) in the
special holder. Do not rest large objects which could obstruct movement or unstable objects on the appliance.
Important! Do not use the appliance when extracted. Make
sure the appliance is inactive before extracting it. The only exception is
adjusting the coffee mill which must be done with the machine out (see
the section "Adjusting the coffee mill").
N.B.! Use original or manufacturer recommended accessories and spare parts only.
Designated use
This appliance is designed and made to prepare coffee and heat
drinks.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from improper
use of the appliance.
This appliance can be installed over a built-in oven if the latter is fitted with a cooling fan at the rear (maximum power: 3 kW).
It is not intended to be used in:
• staff kitchen areas in shops, offices and other working environments;
• farm houses;
• by clients in hotels, motels and other residential type environments;
• bed and breakfast type environments.
Instructions
Danger! This is an electrical appliance, it is therefore important to respect the following safety warnings:
• Never touch the appliance with damp hands.
• Never touch the plug with damp hands.
N.B.! The appliance has a cooling fan. This comes on whenever coffee, steam or hot water is delivered. After several minutes,
the fan goes off automatically.
Read these instructions carefully before using the appliance.
• Keep these instructions
• Failure to respect these instructions may result in burns or damage to the appliance.
The manufacturer is not liable for damage deriving from failure
to respect these instructions.
7
GB
IT
GB
Child safety
PRELIMINARY CHECKS
To lock the control panel, press the
icon (B3) then the OK icon
(B9).
To unlock the control panel, press any icon, then within 5 seconds,
press the OK icon (B9).
Controls after transport
DESCRIPTION
Description of the appliance
(page 3 - A)
A1. Cup tray
A2. Service door
A3. Coffee guide
A4. Grounds container
A5. Brewing unit
A6. Cup tray lights
A7. On/OFF/stand-by button
A8. Control panel
A9. Terminal board
A10. Cappuccino maker (removable)
A11. Tray
A12. Water tank
A13. Coffee spout (adjustable height)
A14. Drip tray
A15. Bean container lid
A16. Bean container
A17. Grinding adjustment knob
A18. Pre-ground coffee funnel door
A19. Measure
A20. Compartment for measure
A21. Pre-ground coffee funnel
A22. Power cable
A23. Main switch
Description of the control panel
(page 3 - B)
N.B.! A light touch is enough to activate the icon.
B1. Display: guides the user in using the appliance.
B2. MENU icon to activate or deactivate menu parameter setting
mode
B3.
child safety icon, to lock the control panel
B4.
icon to select the coffee taste
B5.
icon to select the type of coffee (espresso, small cup, medium cup, large cup, mug)
B6.
icon to deliver hot water
B7-B8.
icons to scroll forwards or backwards through the
menu items
B9. OK icon to confirm the selected item
B10.
icon to deliver a cup of coffee
B11.
icon to deliver two cups of coffee
B12.
icon to deliver steam
8
After removing the packaging, make sure the product is complete and
undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact Customer Services.
Installing the appliance
•
•
•
•
Important!
Installation must be performed by a qualified professional in
compliance with legislation in force in the country of installation (see Built-in installation).
The packing elements (plastic bags, polystyrene foam, etc.)
should be kept out of reach of children.
Do not install the appliance in rooms where the temperature
may drop to 0°C or lower.
Customise the water hardness as soon as possible following
the instructions in the "Setting water hardness" section.
Connecting the appliance
Danger! Check that the mains power supply voltage corresponds to the value indicated on the rating plate on the bottom of
the appliance.
Connect the appliance to an efficiently earthed and correctly installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance, have
the socket replaced with a suitable type by a qualified professional.
To comply with safety directives, an omnipolar switch with a minimum contact distance of 3 mm must be installed.
Do not use multiple sockets or extensions.
Important! Safety cutout devices must be included in the
mains power supply in compliance with the installation regulations
in the country concerned.
DISPOSAL
Electrical appliances must not be disposed of as household
waste.
Appliances with this symbol are covered by European Directive 2002/96/EC.
All unused electric and electronic appliances must be disposed of
separately from household waste by taking them to state authorised
special centres.
Disposing of the unused appliance correctly avoids damage to the
environment and a risk to health.
For more information on disposing of the unused appliance, contact
the local administration, the waste disposal department or the shop
where the appliance was bought.
BUILT-IN INSTALLATION
Verify the minimum measurements required for correct installation
of the appliance.
The coffee maker must be installed in a column and the column
must be firmly fixed to the wall with commercially available brackets.
•
528 m
m
361
mm
m
21 m
m
45 m
595 m
398
mm
m
45 m
m
560 +
850 mm Min 450 + 2 mm
•
Important: all installation or maintenance operations must be performed with the appliance disconnected from the mains electricity supply.
Kitchen furniture in direct contact with the appliance must be heat
resistant (65°C min).
To guarantee correct ventilation, leave a gap at the bottom of the
cabinet (see measurements in figure).
455 mm
•
372 mm
Important:
GB
m
15 m
8 mm
m
45 m
mm
500
Min.
mm
545
m
45 m
200 cm2
9
IT
x 16
x2
x4
GB
Position the rails on the sides of the cabinet as shown in the figure.
Fix with the screws supplied, then extract them completely.
If the coffee maker is installed over a warmer drawer, use the top
surface of this as a reference to position the rails.
In this case, there will be no surface to rest the rails on.
Position the appliance on the rails, making sure the pins are correctly inserted in the housings, then fix it with the screws supplied.
x4
x1
560 +
1 mm
mm
x. 350
appro
Fix the power cable with the clip.
The power cable must be long enough to allow the appliance to be
extracted from the cabinet to fill the coffee bean container.
The appliance must be earthed in compliance with legislation.
Electrical connections must be performed by a qualified
electrician following the instructions.
10
If necessary, correct alignment of the appliance by positioning the
spacers supplied under or at the sides of the support.
USING THE APPLIANCE FOR THE
FIRST TIME
MAKING COFFEE USING COFFEE
BEANS
•
1. The appliance is preset to make coffee with a normal taste.
You can also choose coffee with an extra-mild, mild, standard,
strong or extra-strong taste. There is also a pre-ground coffee
option.
To choose the required taste, press the
icon (B4) a number of times (fig. 7). The required coffee taste is displayed.
2. Place 1 cup under the spouts to make 1 coffee (fig. 9) or 2 cups
for 2 coffees (fig. 8).
Lower the spouts as near as possible to the cup for a creamier
coffee (fig. 10).
3. Press the
icon (B5) (fig. 11) to select the type of coffee:
espresso, small cup, medium cup, large cup, mug.
Press the
icon (B10) (fig. 12) if you want to make a coffee
and the
icon (B11) (fig. 13) if you want to make 2 coffees.
The appliance now grinds the beans and starts delivering the
coffee into the cup.
Once the set amount of coffee has been delivered, the machine
stops delivery automatically and expels the exhausted waste
coffee into the grounds container.
4. After a few seconds, the appliance is ready for use again.
5. To turn the appliance off, press the ON/OFF/stand-by button (A7)
(fig. 1).
(Before going off, the appliance performs an automatic rinse
cycle. Take care to avoid scalds).
NOTE 1: If the coffee is delivered a drop at a time or not at all, see
the "Adjusting the coffee mill" section.
NOTE 2: If the coffee is delivered too fast and the cream is not satisfactory, see the "Adjusting the coffee mill" section.
NOTE 3: Tips for a hotter coffee:
• Proceed as described in the section "Changing and setting menu
parameters", "Rinse" function.
• Unless preheated, do not use excessively thick cups as they will
absorb too much heat.
• Preheat the cups by rinsing them with hot water.
NOTE 4: Coffee delivery can be interrupted at any moment by repressing the previously selected icon.
NOTE 5: As soon as delivery is finished, to increase the quantity of
coffee in the cup, just keep pressing the previously selected icon
within 3 seconds after delivery has finished.
NOTE 6: When the appliance displays "FILL TANK!", fill the tank with
water or the appliance will not deliver coffee.
(It is normal for there to be a little water left in the tank).
NOTE 7: After about 14 single (or 7 double) coffees, the appliance
displays "EMPTY GROUNDS CONTAINER!".
To clean, open the service door on the front of the appliance by pulling the spout (fig. 16), extract the drip tray (fig. 17) and clean.
Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the
mill.
• Customise water hardness as soon as possible following the instructions in the "Setting water hardness" section.
1. Connect the appliance to the mains supply.
Set the required language.
2. To set the language, use the
icons (B7 and B8) to choose
the required language (fig. 2).
When "PRESS OK TO INSTALL ENGLISH" is displayed, press the
OK icon (B9) (fig. 3).
If you set the wrong language, follow the instructions in the "Setting the language" section.
If your language is not available, select one from those displayed. The instructions refer to the English version.
Then follow the instructions displayed:
3. After 5 seconds, the appliance displays "FILL TANK!". Extract
the water tank (fig. 4), rinse and fill with fresh water without exceeding the MAX line.
Replace and push as far as it will go.
4. Place a cup under the hot water spout (fig. 5).
The appliance displays: "HOT WATER press OK".
Press the OK icon (B9) (fig. 3) and after a few seconds a little
water comes out of the spout.
5. The machine now displays "TURNING OFF... PLEASE WAIT" and
goes off.
6. Extract the appliance by pulling it out using the handles (fig. 6).
Open the lid and fill the container with coffee beans, then close
the lid and push the appliance in.
The coffee maker is now ready for normal use.
Important! Never introduce pre-ground coffee, freeze dried
coffee, caramelised beans or anything else which could damage the
appliance.
N.B.: When using the appliance for the first time, you need
to make 4-5 cups of coffee and 4-5 cappuccinos before the appliance gives satisfactory results.
N.B.: Each time you turn the coffee maker on by the ON/OFF
switch (A23), it performs a SELF-DIAGNOSIS cycle and then goes
off. To turn it on again, press the ON/OFF button (A7) (fig. 1)
TURNING ON AND HEATING UP
Each time the appliance is turned on, it performs an automatic preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this cycle.
Danger of burns! During rinsing, a little hot water flows
from the coffee spouts.
To turn the appliance on, press the ON/OFF/stand-by button (A7)
(fig. 1). The message "HEATING UP PLEASE WAIT" is displayed.
When heating is complete, the message changes to "RINSING";
The appliance is at temperature when the message "MEDIUM CUP
standard taste" is displayed.
11
GB
The appliance is now reprogrammed with the new setting and is
ready for use.
You can change the amount of coffee in the small cup, medium cup,
large cup and mug.
IT
GB
N.B.: When the
icon (B11) is pressed, double the
amount of coffee set previously with the
icon (B10) is delivered.
To reset the original settings, see "Resetting default values".
ADJUSTING THE COFFEE MILL
When cleaning, always extract the drip tray completely.
Important! When extracting the drip tray, the grounds container MUST always be emptied. If this is not done, the machine
may be clogged.
NOTE 8: Never extract the water tank while the machine is delivering
coffee.
If it is removed, it will not be possible to make the coffee and the appliance will display "GROUND TOO FINE ADJUST MILL ! PRESS
OK" and then "FILL TANK!". Check the level of water in the tank and
replace in the appliance.
To turn the appliance back on, insert the water spout if not already
in place (fig. 6), then press the OK icon (B9). "HOT WATER PRESS
OK" is displayed.
Press the OK icon (B9) within a few seconds and deliver water from
the spout for about 30 seconds. When delivery stops, the basic
modes are displayed again.
N.B.: The coffee maker may request the operation to be repeated a number of times until the air is completely elminated from
the hydraulic circuit.
N.B.: if this operation is not performed correctly or if the machine is turned off, the basic modes may be displayed, although the
problem is in fact still present.
CHANGING THE QUANTITY OF COFFEE
IN THE CUP
The appliance is set by default to automatically make the following
amounts of coffee:
• espresso
• small cup
• medium cup
• large cup
• mug
To change and memorise the amount of coffee required, for example when making an espresso, proceed as follows:
• Press the
icon (B5) until "ESPRESSO" is displayed.
• Press and hold the
icon (B10) until "PROGRAM QUANTITY ESPRESSO" is displayed.
At the same time, the appliance delivers coffee.
• Press the
icon (B10) again or the OK icon to stop delivery
and memorise the new quantity of coffee.
12
The coffee mill is preset in the factory and should not require adjusting. However, if after making the first few coffees you find that delivery is either too fast or too slow (a drop at a time), this can be
corrected by adjusting the grinding adjustment knob (fig. 14).
Important! The grinding adjustment knob must only be turned when the coffee mill is in operation.
For slower delivery and creamier coffee, turn
one click anticlockwise (finer pre-ground
coffee).
For faster delivery (not a drop at a time), turn
one click clockwise (coarser pre-ground coffee).
MAKING ESPRESSO COFFEE WITH PREGROUND COFFEE (INSTEAD OF BEANS)
•
Press the
icon (B4) (fig. 7) and select the pre-ground coffee function.
• Extract the machine by pulling it outwards using the handles
(fig. 6).
• Lift the central lid, place one measure of pre-ground coffee in
the funnel (fig. 19), push the appliance in then proceed as described in the section "Making coffee using coffee beans".
N.B.: You can make just one coffee at a time by pressing the
icon (B10) (fig. 12).
• After using the machine with pre-ground coffee, to go back to
making coffee using beans, deactivate the pre-ground coffee
function by pressing the
icon (B4) (fig. 7).
NOTE 1: Never introduce pre-ground coffee when the machine is off
or it could spread through the inside of the appliance.
NOTE 2: Never add more than 1 measure, otherwise the appliance
will not make the coffee.
NOTE 3: Use the measure provided only.
NOTE 4: Introduce only pre-ground coffee for espresso coffee machines into the funnel.
NOTE 5: If more than one measure of pre-ground coffee is used and
the funnel clogs, push the coffee down with a knife (fig. 21) then
remove and clean the brewing unit and machine as described in the
"Cleaning the brewing unit" section.
DELIVERING HOT WATER
•
Always make sure the appliance is ready.
•
•
Turn the cappuccino maker outwards and place a container underneath (fig. 5).
Press the
icon (B6) (fig. 20).
The appliance displays: "HOT WATER PRESS OK". Press the OK
icon (B9) again and hot water is delivered from the cappuccino
maker into the container below.
You should not deliver hot water for more than 2 minutes at a
time.
To interrupt, press the
icon (B6) or the OK icon (B2).
The appliance stops delivery once the set quantity is reached.
MAKING CAPPUCCINO (USING THE
STEAM FUNCTION)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Turn the cappuccino maker towards the centre (fig. 5).
Take a container, fill it with about 100 g of milk for each cappuccino
to be made and place it under the cappuccino maker. In choosing
the size of the recipient, bear in mind that the milk doubles or triples in volume. You are recommended to use partially skimmed
milk at refrigerator temperature.
Press the
icon (B12) (fig. 22). "STEAM PRESS OK" is displayed.
Press the OK icon (B9).
Immerse the cappuccino maker in the milk container (fig. 23), taking care not to immerse it for more than half its length.
Steam comes out of the cappuccino maker.
For a creamier froth, immerse the cappuccino maker in the milk
and move the container with slow upward movements.
You should not deliver steam for more than 2 minutes at a time.
When the required temperature is reached, interrupt steam delivery
by pressing the
icon (B12) again or the OK icon (B2).
Make the coffee as described above using sufficiently large cups,
then fill them with the frothed milk prepared previously.
IMPORTANT: always clean the cappuccino system immediately
after use.
Proceed as follows:
Press the
icon (B12) and then press the OK button (B9) to discharge a small amount of steam for a few seconds.
This empties the steam spout of all traces of milk.
IMPORTANT: to ensure the hygiene of the appliance, you are recommended to carry out this procedure each time you make cappuccino to avoid stale milk remaining in the circuit.
Wait for the cappuccino maker to cool down, then holding the cappuccino maker lever firmly in one hand, unscrew the cappuccino
maker itself with the other, turning it anticlockwise and removing it
downwards (fig. 24).
Remove the cappuccino maker nozzle by pulling it downwards.
Wash the cappuccino maker and nozzle thoroughly in hot water.
Make sure the two holes shown in figure 25 are not blocked.
If necessary, clean with a pin.
Replace the nozzle by inserting it upwards into the cappuccino
maker.
Replace the cappuccino maker by pushing it upwards and rotating
it clockwise.
CLEANING
Cleaning the coffee maker
Do not use solvents or abrasive detergents to clean the coffee
maker. A soft damp cloth will suffice.
Never wash any of the components of the coffee maker in the dishwasher.
The following parts of the machine must be cleaned regularly:
• Grounds container (A4).
• Drip tray (A14).
• Water tank (A12).
• Coffee spouts (A13)
• Pre-ground coffee funnel (A21).
• Inside of the machine, accessible after opening the service door
(A2).
• Brewing unit (A5).
Cleaning the grounds container
When "EMPTY GROUNDS CONTAINER!" is displayed, the grounds
container must be emptied and cleaned.
To clean:
• open the service door on the front of the appliance (fig. 16), extract the drip tray (fig. 17) and clean.
• Clean the grounds container thoroughly.
Important! When extracting the drip tray, the grounds container must always be emptied.
Cleaning the drip tray
Important! If the drip tray is not emptied the water might
overflow. This could damage the machine.
The drip tray is fitted with a level indicator (red) showing the level
of water it contains (fig. 27).
Before the indicator protrudes from the cup tray, the drip tray must
be emptied and cleaned.
To remove the tray:
1. Open the service door (fig. 16).
2. Remove the drip tray and the grounds container (fig. 17).
3. Clean the drip tray and grounds container (A4).
4. Replace the drip tray and grounds container (A4).
5. Close the service door.
Cleaning the water tank
1. Clean the water tank (A12) regularly (about once a month) with
a damp cloth and a little mild washing up liquid.
2. Remove all traces of washing up liquid.
Cleaning the spouts
1. Clean the nozzles periodically using a sponge (fig. 28).
2. Check regularly that the holes in the coffee spout are not blocked.
If necessary, remove coffee deposits with a toothpick (fig. 26).
Cleaning the pre-ground coffee funnel
•
Check regularly (about once a month) that the pre-ground cof-
13
GB
fee funnel is not blocked (fig. 21).
IT
GB
Danger! Before performing any cleaning operations, the machine must be turned off by pressing the main switch (A23) and unplugged from the mains power supply. Never immerse the coffee
maker in water.
Cleaning the inside of the coffee maker
1. Check regularly (about once a week) that the inside of the appliance is not dirty.
If necessary, remove coffee deposits with a sponge.
2. Remove the residues with a vacuum cleaner (fig. 29).
8. Replace the drip tray and grounds container.
9. Close the service door.
Cleaning the brewing unit
CHANGING AND SETTING MENU
PARAMETERS
The brewing unit must be cleaned at least once a month.
Important! The brewing unit (A5) must not be removed
when the appliance is on. Do not use force to remove the brewing
unit.
1. Make sure the machine is correctly turned off (see "Turning the
appliance off").
2. Open the service door (fig. 16).
3. Remove the drip tray and grounds container (fig. 17);
4. Press the two red release buttons inwards and at the same time
pull the brewing unit outwards (fig. 30).
Important! Do not use washing up liquid to clean the brewing unit. It would remove the lubricant applied to the inside of the
piston.
5. Soak the brewing unit in water for about 5 minutes, then rinse.
6. After cleaning, replace the brewing unit (A5) by sliding it onto
the internal support and pin at the bottom,
Support
Pin
then push the PUSH symbol fully in until it clicks into place.
N.B.! If the brewing unit is difficult to insert, you must first
adapt it to the right dimensions by pressing it forcefully from the
bottom and top as shown in the figure.
When the appliance is ready, you can use the internal menu to modify the following parameters and functions:
• RINSING
• ADJUST TIME
• LANGUAGE
• AUTO-START
• DESCALE
• COFFEE TEMPERATURE
• AUTO-OFF
• WATER HARDNESS
• RESET TO DEFAULT
• STATISTICS
• SET BEEP
• EXIT
Rinsing
This function enables you to obtain hotter coffee.
Proceed as follows:
• When you turn the appliance on, if you want to make a small
cup of coffee (less than 60 cc), preheat the cup by rinsing it with
hot water.
• If on the other hand more than 2/3 minutes have passed since
the last coffee was made, before requesting another coffee, you
must preheat the infuser by first pressing the MENU icon (B2)
to enter the menu. "RINSING" is displayed.
Press the OK icon (B9).
"OK to confirm" is displayed.
Press the OK icon (B9) again.
Deliver the water into the underlying drip tray or alternatively
use this water to fill (and then empty) the cup to be used for the
coffee to preheat it.
Setting the clock
•
•
•
•
•
7. Once inserted, make sure the two red buttons have snapped out.
14
Press the MENU icon (B2) to enter the menu and then the
icons (B7) and (B8) until "ADJUST TIME" is displayed.
Press the OK icon (B9).
Use the
icons (B7) and (B8) to set the hour, then press
the OK icon (B9) to confirm.
Use the
icons (B7) and (B8) to set the minutes, then
press the OK icon (B9) to confirm.
Press the MENU icon (B2) to exit the menu.
Setting the language
To change the language on the display, proceed as follows:
• Press the MENU icon (B2) to enter the menu, then the
icons (B7) and (B8) to select the "LANGUAGE" function.
• Press the OK icon (B9).
• Press the
icons (B7) and (B8) until the required language is displayed.
• Press the OK icon (B9) to confirm.
• Press the MENU icon (B2) to exit the menu.
Setting auto-start time
This function programmes the time the machine will come on automatically.
• Make sure the clock on the appliance has been set.
• Press the MENU icon (B2) to enter the menu and then the
icons (B7) and (B8) until "AUTO-START" Deactivated" is displayed.
• Press the OK icon (B9).
• "AUTO-START Activate?" is displayed.
• Press the OK icon (B9) to confirm.
• "AUTO-START 07:30" is displayed.
• Use the
icons (B7) and (B8) to set the auto-start time,
then press the OK icon (B9) to confirm.
• Use the
icons (B7) and (B8) to set the minutes, then
press the OK icon (B9) to confirm.
• Press the OK icon (B9). "AUTO-START Activated" is displayed.
• Press the MENU icon (B2) to exit the menu.
The
symbol appears on the display near the time.
Descaling
•
•
•
•
•
•
•
liveries and pauses.
After about 30 minutes "RINSING FILL TANK!" is displayed.
Empty the water tank, rinse to eliminate descaler residues, then
fill with clean water.
Replace the tank full of clean water.
"RINSING press OK" is displayed.
Press the OK icon (B9) again.
Hot water flows out of the spout into the container below and
"RINSING PLEASE WAIT" is displayed.
Wait until "RINSING COMPLETE press OK" is displayed.
Press the OK icon (B9).
"DESCALING COMPLETE" is displayed, followed by "FILL
TANK!".
Fill the tank again with clean water.
The descale programme is now terminated and the appliance is
ready to make coffee again.
NOTE: If descaling is interrupted before completion, the process must be begun again from the beginning.
Important! FAILURE TO DESCALE THE APPLIANCE REGULARLY INVALIDATES THE GUARANTEE.
Changing coffee temperature
To change coffee temperature, proceed as follows:
• Press the MENU icon (B2) to enter the menu and then the
icons (B7) and (B8) until "COFFEE TEMPERATURE" is displayed.
• Press the OK icon (B9).
• Press the
icons (B7) and (B8) to select the required coffee temperature from low, medium and high.
• Press the OK icon (B9) to confirm the temperature selected.
• Press the MENU icon (B2) to exit the menu.
Important! Descaler contains acids. Respect the safety warnings provided by the manufacturer and given on the descaler pack.
Changing the length of time the appliance
remains on
N.B.! Use the descaler recommended by the manufacturer
only. Use of other descalers invalidates the guarantee. Failure to
descale the appliance as described also invalidates the guarantee.
The appliance is set by default to go off automatically 30 minutes
after the last coffee has been made.
To change this interval (max. 120 min), proceed as follows:
• Press the MENU icon (B2) to enter the menu and then the
icons (B7) and (B8) until "AUTO-OFF" is displayed.
• Press the OK icon (B9) to confirm.
• Press the
icons (B7) and (B8) to set the time after
which the appliance will go off (after 30 minutes, 1 hour, 2
hours).
• Press the OK icon (B9) to confirm.
• Press the MENU icon (B2) to exit.
When "DESCALE !" is displayed, the machine requires descaling.
Proceed as follows:
• make sure the machine is ready;
• attach the hot water spout (C7) to the nozzle (A10).
• Press the MENU icon (B2) to enter the menu and then the
icons (B7) and (B8) until "DESCALING" is displayed.
• Press the OK icon (B9) and the appliance displays "DESCALING
OK to confirm".
• Press the OK icon (B9).
"ADD DESCALER press OK" is displayed.
• Empty the tank of water, pour the contents of the descaler bottle into the tank respecting the instructions given on the descaler pack, then add water up to the MAX level marked on the
water tank.
Position a container with a capacity of about 2 litres under the
hot water spout.
• Press the OK icon (B9). Descaler flows out of the hot water
spout into the container below.
"DESCALING…" is displayed.
• The descale programme automatically performs a series of de-
Setting water hardness
The operating period can be extended if required, making descaling
less frequent by programming the machine on the basis of the real
lime content in the water used.
Proceed as follows:
• remove the "Total Hardness Test" strip (attached to page 2) from
its packaging then dip it fully in the water for a few seconds,
Then remove and wait about 30 seconds (until it changes colour
and forms red squares).
• Press the MENU icon (B2) to enter the menu and then the
icons (B7) and (B8) until "WATER HARDNESS" is displayed.
15
GB
IT
•
•
GB
•
•
Press the OK icon (B9).
Press the
icons (B7) and (B8) until the number of spots
coincides with the number of red squares on the test strip (for
example, if there are 3 red squares on the test strip, select
“●●●◦”);
Press the OK icon (B9) to confirm.
The coffee maker is now programmed to provide the descale
warning when actually necessary.
Press the MENU icon (B2) to exit.
Resetting default values (reset)
If you change the original values, the default values can be reset as
follows:
• Press the MENU icon (B2) to enter the menu and then the
icons (B7) and (B8) until "DEFAULT VALUES" is displayed.
• Press the OK icon (B9). "OK to confirm" is displayed.
• press the OK icon (B9) to reset the default values;
"RESET" is displayed for a few seconds.
• Press the MENU icon (B2) to exit the menu.
Statistics
This displays statistics relating to the machine.
To display, proceed as follows:
• Press the MENU icon (B2) to enter the menu and then the
icons (B7) and (B8) until "STATISTICS" is displayed.
• Press the OK icon (B9).
• Press the
icons (B7) and (B8) to verify:
- How many coffees and cappuccinos have been made.
- How many times the machine has been descaled.
- The total number of litres of water delivered.
• Press the MENU icon (B2) once to exit the function or twice to
exit the menu.
Set beep
This activates or deactivates the beep emitted by the machine each
time an icon is pressed or an accessory is inserted/removed.
•
•
•
•
N.B.! The beep is active by default.
Press the MENU icon (B2) to enter the menu and then the
icons (B7) and (B8) until "BEEP Activated" is displayed.
Press the OK icon (B9). "BEEP Deactivate?" is displayed.
Press the OK icon (B9) to deactivate the beep.
Press the MENU icon (B2) to exit the menu.
TURNING THE APPLIANCE OFF
Each time the appliance is turned off, it performs an automatic rinse
cycle which cannot be interrupted.
Danger of burns! During rinsing, a little hot water flows from
the coffee spouts. Avoid contact with splashes of water.
To turn the appliance off, press the ON/OFF button (A7).
The appliance performs the rinse cycle then goes off.
N.B.! If the appliance is not used for an extended period,
place the main switch on the side of the appliance in the 0 position
(A23).
16
TECHNICAL SPECIFICATION
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1350 W
Pressure: 15 bars
Water tank capacity: 1.8 litres
Size LxHxD: 595 x 455 x 398 mm
Weight: 26 kg
The appliance complies with the following EC directives:
•
•
Low Voltage Directive 2006/95/EC and subsequent amendments;
EMC Directive 2004/108/EC and subsequent amendments
Materials and accessories coming into contact with food conform to
European regulation (EC) no. 1935/2004.
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
REMEDY
•
The water tank is empty or positioned
incorrectly.
•
Fill the tank with water and/or insert it
correctly, pushing it as far as it will go.
GROUND TOO FINE ADJUST MILL!
INSERT WATER SPOUT!
press OK
•
The grinding is too fine and the coffee
is delivered too slowly.
•
Turn the grinding adjustment knob one
click clockwise towards "7".
GROUND TOO FINE ADJUST MILL!
(alternating with)
press OK
(then)
FILL TANK !
•
The tank has been removed during delivery.
There is air in the hydraulic circuit.
•
Insert the tank and press the OK icon
(B9). "HOT WATER" is displayed. Hot
water is delivered and the appliance is
once again ready for use.
EMPTY GROUNDS CONTAINER!
•
The grounds container (A4) is too full
or more than 3 days have passed since
you last made coffee (this guarantees
correct hygiene of the machine).
•
Empty the grounds container and
clean, then replace.
Important: when removing the drip
tray, the grounds container MUST be
emptied, even if it is not completely full.
If this is not done, when you make the
next coffees, the grounds container
may fill up more than expected and
clog the machine.
INSERT GROUNDS CONTAINER!
•
After cleaning, the grounds container
has not been replaced.
•
Open the service door and insert the
grounds container.
ADD PRE-GROUND COFFEE!
•
•
Extract the appliance and place preground coffee in the funnel.
•
The "pre-ground coffee" function has
been selected without placing any preground coffee in the funnel.
The funnel (A21) is blocked.
•
Empty the funnel with the help of a
knife as described in the section "Cleaning the pre-ground coffee funnel".
DESCALE!
(alternating with)
MEDIUM CUP STANDARD TASTE
•
The machine must be descaled.
•
The descaling procedure described in
the "Descaling" section needs to be performed as soon as possible.
LESS COFFEE !
•
Too much coffee has been used.
•
Select a milder taste or reduce the
quantity of pre-ground coffee, then
make the coffee again.
FILL BEANS CONTAINER!
•
The coffee beans have run out.
•
Fill bean container
•
The brewing unit has not been replaced after cleaning.
•
Insert the brewing unit as described in
the section "Cleaning the brewing unit".
CLOSE DOOR !
•
The service door is open.
•
Close the service door.
GENERAL ALARM!
•
The inside of the appliance is very dirty.
•
Clean the inside of the appliance thoroughly, as described in the section
"Cleaning and maintenance".
If the message is still displayed after
cleaning, contact a customer services.
INSERT INFUSER ASSEMBLY!
•
GB
REMEDY
17
IT
GB
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
PROBLEM
The coffee is not hot
POSSIBLE CAUSE
REMEDY
•
The cups were not preheated.
•
•
•
•
The brewing unit has cooled down because 2/3 minutes have elapsed since
the last coffee was made.
The temperature set is too low.
•
The coffee is ground too coarsely.
•
•
Wrong type of coffee
•
The coffee is delivered too slowly or a
drop at a time.
•
The coffee is ground too finely.
•
Turn the grinding adjustment knob one
click clockwise towards "7" while the
coffee mill is in operation (fig. 14).
Continue one click at a time until coffee delivery is satisfactory.
The effect is only visible after delivering
two coffees.
The coffee is delivered too quickly.
•
The coffee is ground too coarsely.
•
Turn the grinding adjustment knob one
click anticlockwise towards "1" while
the coffee mill is in operation (fig. 14).
Avoid turning the grinding adjustment
knob excessively otherwise when you
select 2 cups, the coffee may be delivered a drop at a time.
The effect is only visible after delivering
two coffees.
Coffee does not come out of one of the
spouts.
•
The spouts are blocked.
•
Clean the spouts with a toothpick (fig.
26).
The coffee does not come out of the
spouts, but from around the service door
(A2).
•
The holes in the spouts are clogged
with dry coffee dust.
•
•
The coffee guide (A3) inside the service
door is blocked and cannot swing.
•
If necessary, remove coffee deposits
with a toothpick, sponge or stiff bristled
kitchen brush (fig. 26-28).
Thoroughly clean the coffee guide (A3),
particularly near the hinges.
•
The pre-ground coffee may be blocked
in the funnel (A21).
•
The coffee is not creamy enough
Water comes out of the spouts instead of
coffee.
18
•
Warm the cups by rinsing them with
hot water.
Before making coffee, preheat the brewing unit by selecting the RINSING
function in the menu.
Change the set temperature (see paragraph "Changing coffee temperature").
Turn the grinding adjustment knob one
click anticlockwise towards "1" while
the coffee mill is in operation (fig. 14).
Use a type of coffee for espresso coffee
makers.
Clean the funnel (A21) with a wooden
or plastic fork, clean the inside of the
machine.