For detailed operating method read the corresponding content on the instruction manual.
Switch on the appliance
Fill the detergent dispenser
Check the rinse aid level
Check the regeneration
salt level
Load the baskets
Select a programme
Running the dishwasher
Changing the programme
Press the On/Off button to switch on the appliance, Open the door.
With each wash cycle.
Compartment
For programmes with pre-wash only.
(Follow the user instructions!)
Electric indicator on control panel (if provided).
(On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel
(for some models), you can estimate when to fill the salt into
the softener by the number of cycles the dishwasher has run.
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
Press the Programme Button until the selected programme lights up.
( See the section entitled“Operationg instruction”)
Close the door, t urn on the water tap and press the Start/Pause Button. The machine will start working
after about 10 seconds.
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Press the Start/Pause button then press the program button for more than 3 seconds to cancel the
running programme.
3. Select a new programme.
4. Restart the dishwasher.
Add forgotten dishes in the
dishwasher.
1.Press the Start/Pause button to stop the machine.
2.Open the door.
3.Add the forgotten dishes.
4.Close the door, then press the Start/Pause button, the dishwasher will
start running again after 10 seconds.
If the appliance is switched
off during a wash cycle.
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
Switch off the appliance
Turn off the water tap,
unload the baskets
Open the doo r carefully.
Hot steam may esc ape
when the door is opened!
When the working cycle has finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will also dry better.Unload the appliance, starting from the lower basket.
Dear Customer,
This appliance is in tended to be used in household
and similar applications such as:
-staff kitch en areas in shop s, offices and other
working environme nts;
-farm hous es;
-by clients in hotels, motels and othe r residential
type environments;
-bed and breakfast type environments.
Please carefully read this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Keep it as a refer in the later days.
Pass it on to any subsequent owner of the appliance.
This manual contains sections on safety Instructions,
Operating Instructions, Installat ion I nstructions and
Tr oubleshooting Tips, etc.
To review the section on troubleshooting Tips
will help you to solve some common problems
by yourself .
If you can not solv e the problems by yourself ,
please ask for the help of professional technicians.
Control Panel...................................................3
Dishwasher Features.................................... ...3
A、Water Softener...........................................4
B、Loading the Salt in to the Softener.................5
C、Fill the Rinse Aid Dispenser.........................5
D、Function of Detergent .................................6
Attention before or after loading the Dishwasher
Baskets..........................................................9
Loading the upper Basket ...............................10
Loading the Lower Basket ...............................10
Cutlery Basket........................................... ...11
Th e recommended method loading big
dishware.................................................... ...12
Wash Cycle Table...........................................13
Turning on the Appliance................................14
Change the Programme.............. .... ................14
At the Ene of the Wash Cycle...........................14
Filtering System.............................................15
Caring for the Dishwasher..................... . .........16
Positioning the Applian ce................... .. ..........17
About Power Connection........................ . .......17
Water Connec tion.................................. . .......1 8
Start of dishwasher................................ .. ......19
The manufacturer, following a policy of constant
development a nd u pdating of the product, may
make modifications without giving prior notice.
Be fore calling for service........................... . .....20
Error codes..................................... ..............2 1
Technical information.............................. .. .....22
When using your dishwasher, follow the precautions listed below:
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of an electric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipmentgrounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not touch the heating element during or
immediately after use.
(This instruction is only applicable to machines
with a visual heating element.)
Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects on or stand on the
door when it is open. The appliance could tip
forward.
When loading items to be washed :
1) Locate sharp items so that they are not likely
to damage the door seal;
2 ) Warning: Knives and other utensils with
sharp points must be loade d in the basket
with their points down or placed in a
horizontal position.
When using your dishwasher, you should
preve nt plastic items from coming into contact
with the heating element.(This instruction is only
applicable to machines with a visual heatin g
element.)
Check th at the detergent comparment is e mpty
after completion of th e wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer's
recommendations.
Use only deterge nt and rinse additives
designed for an automatic dishwasher.
Never use soap, laun dry dete rgent, or hand
washing detergent in you r dishwa sher. Keep
these products out of the reach of children.
Improper connection of the equipment-grounding
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet. Have a proper outlet installed by a
qualified electrician.
Keep children away from detergent and rinse aid, keep
children away from the open door of the dishwasher,
there could still be some detergent left inside.
This appliance is not intended for use by persons
(including children )with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
Dishwash er detergents are strongly alkaline, they
can be extremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
The door should not be left open,
since this could increase the risk of tripping.
If the s upply cord is damaged, it must be replaced
by the man ufacturer or its serv ice agent or a
similarly qualified person in order to avoid a
hazard.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Please d ispose of packing materials properly.
Use the dishwasher only for its intended function.
During installatio n, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water
mains using new hose sets and that old hose-sets
should not be reused.
The maximum nu mber of place settings to be
washed is 12 .
The maximum pe rmissible inlet water pressure is
1Mpa.
The minimum permissible inlet water pressure is
0.04Mpa .
Dispo se of the dishwasher packaging material correctly.
All pa ckaging materials ca n be recycled.
Plastic parts are marked with the standard international abbreviations:
PE
for polyethylene, e .g. sheet wrapping material
PS
for polysty rene, e.g. padding material
POM
PP
ABS
po lyoxymethylene, e.g. pla stic clips
polypropylene, e.g. Salt filler
Acrylonitrile Butadiene Styrene, e.g. Control Panel .
„
„ Pa ckaging material could be dangerous for children!
For disposing of package and the a ppliance ple ase go to a recycling cen tre. Therefore cut
„ off the power s upply cable and mak e the door closin g device unusable.
Cardboard pac kaging is manufactured from recycled paper and should be dispos ed in the
„ waste paper c ollection for recycling .
By ensuring this product is disposed of correctly, you will help prevent potential n egative
consequences for the environment and human health, which could otherwise be caused
„ by inappropriate waste han dling of this prod uct.
For more detailed information about rec ycling of this product, please con tact your local
city office and your household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.
To get the best performance from your dishwasher, read all operating instructions
before using it for the first time.
1. On/Off Button: to switch On/Off the a ppliance.
2. Program Button : To Press the button to select
appropriate Program.
3. Power indicator :To show when the power on.
4. Program indicators:To show whic h program
you ha ve chose.
5. Half load indicators:To show Half load functions
starting up or n ot.
7. Half load functions Button: To select Half load
functio ns. (With this Ha lf load function you can
only use it when you have only about or less than
6 place setting dish wave, and you will see less
water and energy c onsumption , can only be used with
Intensive, Normal, Eco,Glas s and 60 min .)
8. Sta rt /Pause bu tton: To start the selected
washing program or pau se the washing program
when the machine is working.
6. Salt and rinse aid warning indicators: To show
when the salt container or dispense r need to be refilled.
Ba ck View
Front view
6
1
2
7
8
3
4
5
10
9
1
2
3
Upper Basket
Inner pipe
Lower Baske t
4
5
6
Salt Container
Dispenser
Cup Shelf
7
8
9
Spray arms
Filter assembly
Inlet pipe connector
10
Dra in pipe
Before using your dishwasher for the first time:
A. Set the water softener
B. Add 1.5Kg dishwasher salt and then full fill the salt container with water
C. Fill the rinse aid dispenser
D. Fill in detergent
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which would have
a detrimental or adverse effect on the operation of the appliance.
The higher the content of these minerals and salts, the harder your water is.
The softener should be adjusted according to the hard ness of the water in your area. Your local Water Authority
can advise you on the hardness o f the water in your area.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjustment in the amount of sa lt co nsumed bas ed on the ha rdness of
the water used. This is intended to optimise and customise the level o f salt consumption.
Please follow the steps below for adjustment in salt consumption.
1. Switch on the appliance;
2. Press the Start/Pause button for more than 5 seconds to start the water
softener set model within 60seconds after the appliance was
switched on;
3. Press the Start/Pause button to select the proper set according to
your local environment, the sets will change in the following
sequence: H1->H2->H3->H4->H5->H6;
4. Press the On/Off button or no operation for 5 seconds to end the set up model.
WATER HARDNESS
dH
fH
Clarke
mmol/l
Selector Position
Salt consumption
(gram/cycle)
Auto nomy
(cycles/1kgs)
0~5
0~9
0~6
0~0.94
H1-Soak light bright
0
/
6-11
10-20
7-14
1.0-2.0
H2-1 Hour light bright
20
60
12-17
21-30
15-21
2.1-3.0
H3-1 Hour、Soak light bright
30
50
40
40
18-22
31-40
22-28
3.1-4.0
H4-ECO Light bright
23-34
41-60
29-42
4.1-6.0
H5-ECO、 Soak Light bright
50
30
35-55
61-98
43-69
6.1-9.8
H6-ECO、 1 Hour light bright
60
20
1 dH=1.25 Clarke=1.78 fH=0.178mmol/l
DH: German degree
fH:
French degree
Clark: British degree
The manufactory setting: H4 (EN 50242)
Contact your local water board for information on the hardness of your water supply.
If your model does not have any water softener, you may skip this section.
WATER SOFTENER
The hardness of the wa ter varies from place to plac e. If hard water is used in the dishwasher, de posits will
form on the dish es and utensils.
The appliance is equipped with a special softener that uses a salt container specifically des igned to eliminate
lime and minera ls from the water.
Always use the salt intended for use with dishwasher.
The salt contain er is located beneath the lower basket and should be fill ed as explained
in t he foll owing:
Attention!
Only use salt spe cif ically desi gne d for t he use i n dishwashers! Every other type of
salt not speci fically de sig ned fo r the u se in a d ishwasher, espe cially table salt, will
damage the w ater sof tener. In case of damages caused by the use of unsuitable
salt the ma nuf act urer does not give any wa rranty nor is liable for any damages caused.
Only fil l wi th salt just b efore starting one of the co mp let e washing p rograms.
This wi ll prevent any g rains of salt or salty wate r, which ma y have been spilled,
remaining on the bottom of the machi ne for any period of time, which may cause
corrosi on.
A After the lower basket has been removed, unscrew and remove the cap from the salt container.
B Place the end of the funnel (supplied) into the hole and introduce about 1.5kg of dishwasher salt.
C Full fill the salt container with water,It is normal for a small amount of water to come out of the
salt container.
D After filling the container , screw the cap tightly back clockwise.
E The salt warning light will stop being after the salt container has been filled with salt.
F Immediately after filling the salt into the salt container, a washing program should be started (We suggest to use a short
program ). Otherwise the filter system, pump or other important parts of the machine may be damaged
by salty water. This is out of warranty.
1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how well the salt dissolve s, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the con trol panel (for some Mode ls),you can estimate when to fill
the salt into the softener by the cycles that the dishwasher has run.
2. If there are spills of the salt, a soak or a rapid program should be run to remove the excessive sa lt.
3.If the machine needs to be dumped for the reasons of tra nsit, repair and so on, please use the bibulous cloth or
analog to blot up th e water in the salt containe r, and screw the cap tightly, afterward, transit or repair the machine.
After transiting or repairing the mach ine and c onfirmin g it in order, load the salt into the softener according to the
process of “B. Loading the salt into the Softener”. Otherwise , it c ould be make the big damage to the ma chin e, for
examp le, rustiness, conk and so on. Such problems are out of the guarantee ran ge.
Rinse Aid Dispenser
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can
leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is
designed to use liquid rins e aids. The rinse aid dispenser is located inside the door next to the detergent dispenser.
To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely
black. The volume of the rinse aid container is about 110ml.
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
When to Refill the Rinse Aid Dispenser
If there is no rinse-aid warning light in the control panel, you can estimate the amount from the colour
of the optical level indicator " C "located next to the cap. When th e rinse-aid c ontainer is full, the whole
indicator will be dark .As the rinse -aid diminishes, the size of the dark dot decreases. You should never let
the rinse aid leve l fall 1 / 4 full.
As the rinse aid d iminishes, the size o f the black dot
on the rinse aid level indicator changes, as illustra ted below.
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
1
2
3
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming
during the next wash. Don't forget to replace the cap before you close dis hwa sher door.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or four settings. Always start with the dispenser
set on "4". If spots and poor drying are a p roblem, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the dial to "5". If the
dishes still are not drying properly or are show spots, adjust the dial to the next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitis h stains on your dishes or a bluish film on glassware or
knife blades.
Detergents with its chemical ingredients are necessary to remove dirt, c rush dirt and transport it out of the dishwasher.
Most of the commercial quality deterge nts are suitable for this purpose.
Attention!
Proper Use of Detergent
Use only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.
Don't put powdered detergent into the dispenser u ntil you're re ady to wash dish es.
Detergents
There are 3 sorts of d etergents
1.With phosphate and with ch lorine
2.With phosphate and without chlorine
3.Without phosphate and without chlorine
Normally new pulverised detergent is with out phosphate. Thus the water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt con taine r even when
the hardness of water is only 6 °dH. If dete rgents witho ut phosphate are used in the case of hard water
often white spots appear on d ishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Stron g and coloured spots will not
be removed completely. In this case please choose a program with a higher temperature.
Concentrated Detergent
Based on their chemical composition, deterge nts can be split in two basic types:
conventional, alkaline dete rgents with caus tic comp onents
low alkalin e co ncentrated detergen ts with n atural enzymes
Detergent Tablets
Detergent tablets of diffe rent brands disso lve at different speeds. For this reason some
detergent tablets cannot dissolve and develop the ir full cleaning power during short
programs. There fore please use long programs wh en u sin g deterg ent tablets, to
ensure the complete removal of detergent residua ls.
Detergent Dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the wash cycle table . Your dis hwa sher uses less de tergent and rinse aid than
Conventional dis hwa sher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More heavily soiled items need more detergent. Alway s ad d the
detergent just be fore starting the dish was her, otherwise it could get damp and will not
dissolve properly.
Amount of Detergent to Use
If the lid is closed: press release button. T he lid will sp ring open.
Always add the detergent just before starting each wash cycle.
Only use branded detergent aid for dishwasher.
Dishwasher detergent is corrosive! Take care to keep it out of reach of c hildren.
Fill in Detergent
A
B
Fill the detergent dispenser with detergent.
The marking indicate s the dosing levels , as
illustrate d on the righ t:
A
The place of main wash cycle deterg ent placed.
B
The place of pre-wash cycle deterge nt placed.
Plea se o bserve the manufacturers dosing and storage
Recommendations as stated on the detergent pac kaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
detergent do se in the pre-wash detergent chamber. This detergent will take effect during the pre-wash phas e.
You find information about the amount o f detergent for th e single programme on the last page .
Please aware, tha t according to the level soiling and the specific hardness of water differences are possible.
Please observe th e manufacturer's rec ommendations on the de tergent packaging.
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further
information from the detergent manufacturers.
For particular items, select a program with as low a temperature as possible.
To prevent damage, do not take gla ss a nd c utlery out of the dishwasher immediately
after the programme h as ended.
Are not suitable
Are of limited suitability
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that are not
temperature resistant
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Some types of glasses can become
dull after a large number of washes
Silver and aluminum parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
(For best performance of the dishwasher, follow these loading guide lines.
Features and appearance of baskets and cutlery baskets may vary from your model.)
Scrape off any large amounts o f leftover food. Soften remnants of burnt food in pans.
It is not necess ary to rinse the d ishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots /pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that the spray arms can rotate freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
Load hollow items suc h as cup s, glasses, pans etc. With the opening facing downwards so that
water can not collect in the con tainer or a deep b ase.
Dishes and items of cutlery must not lie ins ide one another, or cover each oth er.
To avoid damage to glasse s, th ey must not touc h.
Load large ite ms which are most difficult to clea n into the lower bask et.
The upper basket is designed to ho ld more delicate and lighter dishware such as glasses , coffee
and tea cups
Long bladed knives stored in an upright position are a potential haza rd!
Long and/or sharp items o f cutlery such as carving kniv es must be positioned
horizonta lly in the upper b asket.
Please do not ove rload yo ur dishwasher. This is important for good results and for
reasonab le consumption of energy.
To prevent water dripping from the uppe r basket into the lower basket, we recommend that you
empty the lower basket first and then the upper basket.
The u pper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and
tea cups and saucers, as well as plates, small bowls
and shallow pans (as long as they are not too dirty).
Position the dishe s an d co okware so that they will
not get moved by the spray of wate r.
We suggest that you place large items and the most
difficult to clea n ite ms are to be placed into the lo wer
basket: such as pots, pans, lids, se rving dishes and
bowls, as shown in the figure below. It is pre ferable to
place serving dishes and lids on the side of the rack s
in order to avoid blocking the ro tation of the top spray
arm.
Please be reminded that:
Pots, serving bowls, etc, must always be placed top down.
Deep pots should be slan ted to allow water to flow out.
The Botto m Basket features fo lding spikes so that larger or more pots and pans can be loaded.
Adjusting the Upper Basket
Folding back the cup shelives
The height of the upper basket can be adjusted in order to
create mo re space for large utensils both for the upper
/lower basket. The height of the upper basket can b e
adjusted by placing the wheels on different height of the
rails. Long items, serving cutlery, salad servers and knives
should be placed on the shelf so that they do not obstruct
the ro tation of the spray arms..
Fo r better stacking of po ts and pans,
the spikes c an b e folded down as
sho w in the picture right.
Folding Spikes of Lower Basket
Fo r better stacking of pots and pans,
the spikes can be folded down as
show in the picture right.
Cutlery should be placed in the cutlery basket with the handles at the bottom. If the rack has side baskets, the
spoons should be loaded separately into the appropriate slots, espe cially long utensils should be placed in the
horizontal position at the front of the upper basket as shown in the picture.
Do no t let any item extend through th e bottom.
Always load sharp utensils with the sharp point down!
(
Normal
Intensive
Glass
Eco.
( * EN 5 02 42 )
60 min
Soak
) Means: need to fill rinse into the Rinse-Aid Dispenser.
Pre-wash(45 ℃)
Wash (50 ℃)
For normally soiled loads,
such as pots , plates,glasses Rinse
Rinse (60 ℃)
and lightly soiled pans.
Drying
5/25g
(or 3in1 )
175
1.15
15
Pre-wash(50 ℃)
Pre-wash
Wash (65 ℃)
Rinse
Rinse(55℃)
Drying
5/25g
(or 3in1 )
160
1.4
19
20g
110
0.95
15.8
5/25 g
(or 3in1 )
170
1.02
12
5/25g
60
1.1
11
8
0.1
3.8
For heaviest soiled crockery,
and normally soiled pots、
pans、dishes etc with dried
on soiling.
For lightly soiled crockery
and glass
Standard daily cycle for
normally soiled loads, such
as pots、plates、glasses.
For lightly so iled loads that
do not need exce llent dry ing
effic iency.
Pre-wash
wash(40℃)
Rinse
Rinse(60℃)
Drying
Pre-wash
Wash (50 ℃)
Rinse
Rinse(60℃)
Drying
Pre-wash(50 ℃)
Wash(60℃)
Rinse (60℃)
Drying
To rinse dishes that you plan Rise
to wash later that day
*EN 50242 : This programme is the test cycle. The information for comparability test
in accordance with EN 50242, as follows:
Capacity: 12 setting
Position Upper ba sket: upper wheels on rails
Rinse aid setting: 6
PI:0.55w;Po:0.45w
Starting a cycle wash
1 Draw out the lowe r and upper basket, load the dishes and push them back.
It is commended to load the lower basket first, then the uppe r one (see the section entitled
“Loading the Dishwasher”).
2 Pour in the detergent (see the section entitled“Salt, Detergent and Rinse Aid”).
3 Inse rt the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification
of th e so cket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
4 Close the door, press the On/OffButton , and the On/Off light will turn on.
5 Turn the program Selector clockwise , the wash program will be changed as follows direction:
Normal-> Intensive->Glass-> Eco-> 60 min ->Soak ;
If a program is se lected, the response ligh t will light. Then press the Start/Pause button, the
dishwasher begin s to start.
When you press the Start/Pause button to pause during washing, the running indicator will
stop blinking and the dishwasher will mooing every minute unless you press the
Start/Pause button to start.
Premise:
A cycle that is underway can on ly be modified if it has only been running for a short time. Otherwise, the
detergent may have already be en released, a nd the appliance may have already drained the wash water.
If this is the case , the detergent dispenser mu st be refilled (see the section entitled " Loading the
Detergent " ).
2 Press the On/Off button to stop washing , Then press this button to reset , Then you can change the progra m to
the des ired cycle setting (see the section entitled " Sta rting a wash cycle. . ." ).
1
If you open the door during a wash cycle , the machine will pause. The program light will
stop blinking and the buzzer will mooing every minute unless you close the door . After
you close the door ,the machine will keep on working after 10 seconds.
If your model has broken remember function, the machine will go on to finish the selected
program after the power cut .
A forgotten dish can be added any time before the detergent cup opens.
4 Add forgotten dishes.
1 Press the Start/Pause Button to stop the washing.
2 Open the door a little .
5
Close the door
the spray arms stop working, you can open the door
3 After
completely.
6
Press the Start/Pause Button, the dishwasher will run
after 10 seconds.
When the wo rking cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supp ly and open the door of the dishwasher.
Wait for a few minutes before unlo ading th e dishwasher to avoid ha ndlin g the dishes and utensils while they
are still hot and more susceptible to break age. The y will also dry better.
Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressing the On/Off Button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
Wash th e arms in When
soapy following
and warmthis
water
and use from
a softstep1
brushtotostep 3, the filter system will be removed;
procedure
It is dangerous
tothem
openthoroughly.
the door when washing, because the hot water may scald you.
clean the jets. Replace
them
afteritrinsing
when following
from Step
3 to Step 1, the filter system will be installed.
The filter prevents larger remnants of food or other objects from getting inside the pum.
The residues may block the filter, in this case they must be removed.
The filter system consists of a coarse filter,a flat (Main filter)
And a microfilter(Fine filter).
Main filter
2
1
Fo od and soil particles trap ped in this filter are pulverized by a
specia l jet on the lower spray arm and washed down to drain.
1
Coarse filter
2
La rger ite ms, such as p ieces of bones or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on the top of this
filter and lift out.
3
Fine filter
3
This filter holds soil and food residues in the sump area a nd
preve nts it from being redeposit on the dishes during wa sh cycle.
Filter assembly
The filter efficiently re mo ves food particle s from the wash water, allowing it to be rec ycled during the cycle.
For best performance and results, the filter must be cleaned re gularly. For this reason, it is a goo d idea to
remove the larger food particles trapp ed in the filter after e ach was h cycle by rinsing the semicircular filter and
cup under runnin g water. To remove the filter device, pull the cup handle in the upward d irection.
The d ishwasher must never b e used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
1
Step 1:Turn the filter in anti-clockwise direction,
2
Step 2 :lift the filter assy up
When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.
Remarks:
- Inspect the filters for blo cking a fter e very time the dishwa sher has been used.
- By unscrewing the coarse filter, you can remove the filter system. Re move any foo d remna nts and
clean the filters under running water.
The entire filter assembly should be cleaned once a week.
Cleaning the Filter
To clean the coarse filter and the fine filter, use a c leaning b rush. Reassemb le the filter p arts as shown in the figures
on the last page and reinsert the entire assembly in the dis hwa sher, positio ning it in its seat and pressing downwards.
When cleaning the filters, don't knock on them. Otherwise, the filters could be
contorted and the performance of the dishwasher could be decreased.
The control panel can be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Cleaning The Door
To clean the e dge around the door, you should use only a soft warm, damp cloth.
To avoid pene tration o f wa ter into the door lock and electrical components, do not
use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door loc k
and electrical components.
Abrasive agents or some paper towels shou ld not be used becau se of the risk of
scratching or leaving spots on the stainless steel surface.
Protect Against Freezing
please take frost protection measures on the dishwasher in winter. Every time a fter washing cycles,
please operate as follows:
1.Cut off the electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain the water from the inlet pipe an d water valve. (Use a pan to gather th e water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
If your dishwasher cannot work because of the ice,
please contact professional service persons.
Cleaning the Spray Arms
It is necessary to clean the spra y arms re gularly fo r hard
wate r che micals will clog the sp ray arm jets a nd bearings.
To remove the up per spray arm, hold the nut, rotate the arm
clockwise to remove it.
To remove th e lower spray arm, pull out the spray arm u pwa rd.
Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.
After Every Wash
When not in Use for a LongTime
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odours are not trapped inside.
It is recommend that you run a was h cy cle with the
dishwasher empty an d the n remove the plug from the
socket, turn off the wa ter supply and leave the door of
the appliance slightly open. This will help the d oor
seals to last longer and prevent odours from forming
within the appliance.
Remove the Plug
Before cleaning or performing maintenance, always
remove the plug from the socket.
No Solvents or Abrasive Cleaning
To cle an the e xterior a nd rubber p arts of the dishwasher,
do not use solvents or abrasive cle aning products.
Only use a clo th with warm so apy water.
To remove spots o r stains from the surface of the
interior, use a cloth da mpened with water a n a little
vinegar, o r a cleaning pro duct mad e specifically for
dishwashers.
Moving the Appliance
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
Seals
One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. T he dishwasher is equipped with water supply and drain hoses th at can
be positioned either to the righ t or the left sides to facilitate proper installation.
Once the appliance is positioned for levelling, the height of the dishwashe r
may be altered via adjustment of the screwing level of the feet. In any case,
the applia nce should not be inclined more than 2 .
For personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
Plea se look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp , time delay fuse or c ircuit breaker recommended and provide separate circuit serving
only this appliance.
Ensure the voltage and frequency of the power being correspond s to
those on the rating plate. Only in sert the plug into an electrica l socke t which is earthed
prop erly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a a daptors or the like as
they could cause ove rheating an d burns.
This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for the electric current. This appliance is equipped with a
cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
Improper connection of the equipment earthing conductor can result in the risk of an
for personal safety:
electric shock.
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
Check with
qualified
electrician
or service representative
if you areTHE
in doubt
whether the
DO a
NOT,
UNDER
ANY CIRCUMSTANCES,
CUT OR REMOVE
EARTHING
appliance
is properly earthed.
CONNECTION
FROM THE POWER CORD.
Do not modify the plug provided with the appliance. If the plug does not fit properly to the
outlet, please have a qualified electrician to install a proper outlet.
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure
that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time , let the
water run to make sure that the water is clear. This precaution is needed to avoid the
risk of the water in let to be blocked and damage the a ppliance.
Please close the hydrant after using.
Insert the drain h ose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the ho se must be less than 1000mm.
Front
NOTE
The top of the hose
must be less than
1000mm.
Drain pipe
Counter
A
B
φ 40mm
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the excess water in hoses cann ot be drained dire ctly
into the sink. It will be necessary to drain excess water from hoses into a bo wl o r suitable
container that is held outside and lower th an the sink.
Water Outlet
Connect the water drain hose. The drain hose mu st be correctly fitted to avoid water leaks.
Ensure that the water dra in hose is no t kin ked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced .
Syphon Connection
The waste connection must be at a he ight less than 10 00 mm (maximum) from the b ottom of the dish.
The water drain hose sho uld be fixed .
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly
2
3
4
5
6
7
The inlet valve is open
There is a leakage at the connections of the conducts
The wires are tightly connected
The power is switched on
The inlet and drain hoses are knotted
All packing materials and printings should be taken out from the dishwasher
After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
Fuse blown, or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Water pressure is low
Check that the water supply is connected properly and
the water is turned on.
Door of dishwasher
not properly closed.
Make sure to close the door properly and latch it.
Kink in drain hose
Check drain hose.
Filter clogged
Check coarse the filter
(see section titled " Cleaning The Filter ")
Kitchen sink clogged
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Improper detergent
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 1 gallon of cold water to the tub. Close and latch the
dishwasher, then select any cycle. Dishwasher will drain
out the water at the first step.Open the door after draining
is stop and check if the suds is disappeared.
Repeat if necessary.
Spilled rinse-aid
Always wipe up rinse-aid spills immediately.
Detergent with
colourant was used
Make sure that the detergent is the one without
colourant.
Hard water minerals
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
The affected items are
not corrosion resistant.
A programme was not
Always run the quick wash programme .
without any crockery in the dishwasher and
run after dishwasher
without selecting the Turbo function (if present),
salt was added.
Traces of salt have
after adding dishwasher salt.
gotten into the wash cycle.
The lid of the softer
is loose
Check the lip .Ensure the fix is fine.
A spray arm is
knocking against
an item in a basket
Interrupt the programme, and rearrange the items
which are obstructing the spray arm.
Items of crockery
are loose in the
wash cabinet
Interrupt the programme,
and rearrange the items of crockery.
This may be caused
by on-site installation
or the cross-section of
the piping.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
The dishes were not
loaded correctly.
See notes in " Loading the Dishwasher Baskets ".
The programme was
not powerful enough.
Select a more intensive programme.
See" Wash Cycle Table ".
Not enough detergent
was dispensed.
Use more detergent, or change your detergent.
Items are blocking
the path of spray arms.
Rearrange the items so that the spray can rotate freely.
The filter combination
in the base of wash
cabinet is not clean or
is not correctly fitted.
This may cause
the spray arm jets
to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets. See "Cleaning the Spray
Arms".
Combination of soft
water and too much
detergent.
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Aluminum utensils
have rubbed against
dishes.
Use a mild abrasive cleaner to eliminate those marks.
Dishes block
detergent cups.
Re-loading the dishes properly.
Improper loading
Load the dishwasher as suggested in the directions.
Too little rinse-aid
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Dishes are removed
too soon
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
Wrong program
has been selected
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Use of cutlery with
a low-quality coating
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
When some malfunctions come on, the appliance will display error codes to warn you:
The Soak light flicker fleetly
Longer inlet time.
Faucets is not opened, or water intake is
restricted,or water pressure is too low.
The ECO light flicker fleetly
Overflow.
Some element of dishwasher leaks .
If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
Height :
Width :
Depth :
Water pressure:
Power supply:
Capacity:
845mm
598 mm
600mm
0.04-1.0MPa
see rating label
12 place settings
21
Technical Data Sheet
Sheet of household dishwasher according to EU Directive 1059/2010:
Manufacturer
MORA
Type / Description
SM630W
Standard place settings
12
Energy efficiency class
1
A+
Annual energy consumption
2
291 kWh
Energy consumption of the standard cleaning cycle
1.02 kWh
Power consumption of off-mode
0.45 W
Power consumption of left-on mode
0.55 W
Annual water consumption
3
3360 liter
Drying efficiency class
4
A
Standard cleaning cycle
5
ECO 50
Program duration of the standard cleaning cycle
170 min
Noise level
52 dB(A) re 1 pW
Mounting
Free standing
Could be built-in
Yes
Height
84.5 cm
Width
59.8 cm
Depth (with connectors)
60 cm
Power consumption
1930 W
Rated voltage / frequency
230 V~ / 50 Hz
Water pressure (flow pressure)
0.4-10 bar = 0.04-1 Mpa
NOTE
1 A + + + (highest efficiency) to D (lowest efficiency)
2 Energy consumption
291 kWh per year, based on 280 standard cleaning cycles using cold water fill and
the consumption of the low power modes. Actual energy consumption will depend on how the appliance is used.
3 Water consumption
3360 litres per year, based on 280 standard cleaning cycles. Actual water consumption
will depend on how the appliance is used.
4 A (highest efficiency) to G (lowest efficiency)
5 This program is suitable for cleaning soiled normally soiled tableware and that it is the
most efficient programme in terms of its combined energy and water consumption for
that type of tableware.
The device meets the European standards and the directives in the current version at delivery:
- LVD 2006/95/EC
- EMC2004/108/EC
- EUP 2009/125/EC
The above values have been measured in accordance with standards under specified operating conditions.
Results may vary greatly according to quantity and pollution of the dishes, water hardness,
amount of detergent, etc.
The manual is based on the European Union's standards and rules.
22