5910 Ethernet Gateway Module

5910 Ethernet Gateway Module
Hardware Manual
2/24/2017
5910 Ethernet Gateway Module
Copyright © 2014 - 2017 Schneider Electric Canada Inc.
All rights reserved.
The information provided in this documentation contains general descriptions
and/or technical characteristics of the performance of the products contained
herein. This documentation is not intended as a substitute for and is not to be
used for determining suitability or reliability of these products for specific user
applications. It is the duty of any such user or integrator to perform the
appropriate and complete risk analysis, evaluation and testing of the products
with respect to the relevant specific application or use thereof. Neither Schneider
Electric nor any of its affiliates or subsidiaries shall be responsible or liable for
misuse of the information contained herein. If you have any suggestions for
improvements or amendments or have found errors in this publication, please
notify us.
No part of this document may be reproduced in any form or by any means,
electronic or mechanical, including photocopying, without express written
permission of Schneider Electric.
All pertinent state, regional, and local safety regulations must be observed when
installing and using this product. For reasons of safety and to help ensure
compliance with documented system data, only the manufacturer should perform
repairs to components.
Trademarks
Schneider Electric, ClearSCADA, SCADAPack, Solarpack, Realflo, Telepace,
Telebus, SCADAServer, and Modbus are trademarks and the property of
Schneider Electric SE, its subsidiaries and affiliated companies. All other
trademarks are the property of their respective owners.
Microsoft and Windows are registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Address
Schneider Electric
Telemetry & Remote SCADA Solutions
415 Legget Drive, Suite 101, Kanata, Ontario K2K 3R1 Canada
Direct Worldwide: +1 (613) 591-1943
Fax: +1 (613) 591-1022
Toll Free within North America: 1 (888) 267-2232
www.schneider-electric.com
Document (Version 2.27.1.197) 2/24/2017
2
5910 Ethernet Gateway Module
Table of Contents
Technical Support..........................................................................5
Technical Support: Americas, Europe, Middle East, Asia ..................................... 5
Technical Support: Australia .................................................................................. 5
Safety Information .........................................................................6
Important Information ............................................................................................. 6
Please Note ............................................................................................................ 7
Before You Begin ................................................................................................... 7
Operation and Adjustments ................................................................................... 7
Acceptable Use ...................................................................................................... 8
About the Book ..............................................................................9
At a Glance ............................................................................................................ 9
Overview .......................................................................................10
Installation ....................................................................................11
Field Wiring .......................................................................................................... 12
Ethernet Connection ............................................................................................ 13
Power Connections .............................................................................................. 13
I/O Bus Connection .............................................................................................. 13
External Power Connection using an AC adapter ............................................... 13
External Power Connection using an external power source .............................. 14
Configuration Jumpers ......................................................................................... 14
LED Indicators ...................................................................................................... 15
Operation ......................................................................................16
Maintenance .................................................................................17
Troubleshooting ................................................................................................... 17
Specifications ..............................................................................18
Approvals and Certifications ......................................................19
Document (Version 2.27.1.197) 2/24/2017
3
5910 Ethernet Gateway Module
Index of Figures
Figure 1: 5910 Ethernet Gateway Module ......................................................... 10
Figure 2: 5910 Module Layout ........................................................................... 11
Figure 3: 5910 Ethernet RJ-45 Connection ........................................................ 13
Document (Version 2.27.1.197) 2/24/2017
4
5910 Ethernet Gateway Module
Technical Support
Questions and requests related to any part of this documentation can be directed
to one of the following support centers:
Technical Support: Americas, Europe, Middle East, Asia
Available Monday to Friday 8:00am – 6:30pm Eastern Time
Toll free within North America
1-888-226-6876
Direct Worldwide
+1-613-591-1943
Email
supportTRSS@schneider-electric.com
Technical Support: Australia
Inside Australia
1300 369 233
Email
au.help@schneider-electric.com
Document (Version 2.27.1.197) 2/24/2017
5
5910 Ethernet Gateway Module
Safety Information
Important Information
Read these instructions carefully and look at the equipment to become familiar with the device
before trying to install, operate, service, or maintain it. The following special messages may
appear throughout this documentation or on the equipment to warn of potential hazards or to call
attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning safety message
indicates that an electrical hazard exists, which will result in personal
injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, can result in
death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can
result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
Document (Version 2.27.1.197) 2/24/2017
6
5910 Ethernet Gateway Module
Please Note
Electrical equipment should be installed, operated, serviced, and maintained only
by qualified personnel. No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material.
A qualified person is one who has skills and knowledge related to the
construction, installation and operation of electrical equipment and has received
safety training to recognize and avoid the hazards involved.
Before You Begin
Do not use this product on machinery lacking effective point-of-operation
guarding. Lack of effective point-of-operation guarding on a machine can result in
serious injury to the operator of that machine.
WARNING
EQUIPMENT OPERATION HAZARD

Verify that all installation and set up procedures have been completed.

Before operational tests are performed, remove all blocks or other
temporary holding means used for shipment from all component devices.

Remove tools, meters, and debris from equipment.
Failure to follow these instructions can result in death or serious injury.
Follow all start-up tests recommended in the equipment documentation. Store all
equipment documentation for future reference.
Test all software in both simulated and real environments.
Verify that the completed system is free from all short circuits and grounds,
except those grounds installed according to local regulations (according to the
National Electrical Code in the U.S.A, for instance). If high-potential voltage
testing is necessary, follow recommendations in equipment documentation to
help prevent accidental equipment damage.
Operation and Adjustments
The following precautions are from the NEMA Standards Publication ICS 7.11995 (English version prevails):

Regardless of the care exercised in the design and manufacture of
equipment or in the selection and ratings of components, there are hazards
that can be encountered if such equipment is improperly operated.

It is sometimes possible to misadjust the equipment and thus produce
unsatisfactory or unsafe operation. Always use the manufacturer’s
instructions as a guide for functional adjustments. Personnel who have
Document (Version 2.27.1.197) 2/24/2017
7
5910 Ethernet Gateway Module
access to these adjustments should be familiar with the equipment
manufacturer’s instructions and the machinery used with the electrical
equipment.

Only those operational adjustments actually required by the operator should
be accessible to the operator. Access to other controls should be restricted to
help prevent unauthorized changes in operating characteristics.
Acceptable Use
SCADAPack controllers and expansion modules are intended for use in
monitoring and controlling non-critical equipment only. They are not intended for
safety-critical applications.
WARNING
UNACCEPTABLE USE
Do not use SCADAPack controllers and expansion modules as an integral part of
a safety system. These devices are not safety products.
Failure to follow these instructions can result in death or serious injury.
CAUTION
EQUIPMENT OPERATION HAZARD
When devices are used for applications with technical safety requirements, the
relevant instructions must be followed.
Use only Schneider Electric software or approved software with Schneider Electric
hardware products.
Failure to follow these instructions can result in minor or moderate injury.
Document (Version 2.27.1.197) 2/24/2017
8
5910 Ethernet Gateway Module
About the Book
At a Glance
Document Scope
This manual describes the operation and maintenance of the 5910 Ethernet
Gateway module.
Validity Notes
This document is valid for all versions of the 5910 Ethernet Gateway module.
Product Related Information
WARNING
UNINTENDED EQUIPMENT OPERATION
The application of this product requires expertise in the design and
programming of control systems. Only persons with such expertise should be
allowed to program, install, alter and apply this product.
Follow all local and national safety codes and standards.
Failure to follow these instructions can result in death or serious injury.
User Comments
We welcome your comments about this document. You can reach us by e-mail at
supportTRSS@schneider-electric.com.
Document (Version 2.27.1.197) 2/24/2017
9
5910 Ethernet Gateway Module
Overview
The Model 5910 Ethernet Switch is a five port unmanaged switch used to route
Ethernet messages. It is easy to install and operate as no configuration is
necessary. Once the Ethernet connections are made and the unit is powered up,
the 5910 will begin to operate.
The 5910 mounts on a DIN rail and is powered from the 5V available in
SCADAPack controllers and other 5000 systems. The 5910 can also be powered
from 11-30Vdc sources such as 12Vdc batteries, 24Vdc power supplies or AC
adapters. The 5910 is available with a desktop mounting option.
Applications include in-plant I/O and connectivity between SCADAPack
controllers and operator workstations, other PLC devices and SCADA systems
communications that uses 10BaseT (10 Mbps) or 100BaseT (100 Mbps) in an
industrial environment.
Figure 1: 5910 Ethernet Gateway Module
Document (Version 2.27.1.197) 2/24/2017
10
5910 Ethernet Gateway Module
Installation
The 5910 Ethernet Switch is available in two standard versions, the model 5910
and the model 5910SA. The model 5910 is a standard 5000 module that
connects to the system I/O Bus as an integrated part of a Schneider Electric
system. The model 5910SA is a stand-alone version of the 5910 and is used with
other devices such as personal computers. Both versions of the modem are
identical in every respect except that the 5910SA has rubber feet for desktop
mounting.
Power Input
11-30Vdc
+
--
2
1
Power
Port1 Port2 Port3 Port4 Port5
Link/Act
P8
4
3
Speed
J1
External Power
11-30Vdc
P1
Bus Power 5V
Port1
P2
Port2
P3
Port3
Port4
Port5
P7
Figure 2: 5910 Module Layout
Document (Version 2.27.1.197) 2/24/2017
11
5910 Ethernet Gateway Module
Field Wiring
WARNING - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY
FOR USE IN HAZARDOUS LOCATIONS.
AVERTISSEMENT - LA SUBSTITUTION DE COMPOSANTS PEUT AFFECTER
LA CONVENANCE POUR UNE UTILISATION DANS DES EMPLACEMENTS
DANGEREUX.
WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS LOCATIONS,
TURN OFF POWER BEFORE REPLACING OR WIRING MODULES.
AVERTISSEMENT – RISQUE D'EXPLOSION – DANS DES EMPLACEMENTS
DANGEREUX, COUPEZ L'ALIMENTATION AVANT DE REMPLACER OU DE
CÂBLER DES MODULES.
WARNING - do not connect/disconnect circuits unless area is known to be nonhazardous.
AVERTISSEMENT - Ne connectez/déconnectez pas les circuits à moins que la
zone soit considérée non dangereuse.
Power, input and output (I/O) wiring must be in accordance with Class I, Division
2 wiring methods Article 501-4 (b) of the National Electrical Code, NFPA 70 for
installations in the U.S. or as specified in Section 18-1J2 of the Canadian
Electrical Code for installations within Canada and in accordance with the
authority having jurisdiction.
The 5910 module has six connectors for field wiring. Refer to Figure 2: 5910
Module Layout for the location of these connectors.

The five Ethernet connections are terminated at the RJ-45 modular jacks
labeled Ports1 through 5. The RJ-45 modular jack pin-out is compatible with
straight-through Ethernet cables and cross-over Ethernet cables. See the
Document (Version 2.27.1.197) 2/24/2017
12
5910 Ethernet Gateway Module

Ethernet Connection section for more information.

External power in the range of 11 to 30Vdc in maybe connected to pins 1 and
2 of P8. External power may come from any DC power source such as a 12V
battery, 12Vdc AC adapter or 24Vdc power supply. See the Configuration
Jumpers section for setting J1 and the Specifications for the current
requirements.
An AC adapter cannot be used in Hazardous Locations.
Document (Version 2.27.1.197) 2/24/2017
13
5910 Ethernet Gateway Module
Ethernet Connection
The Ethernet network connects to the RJ-45 modular jacks labeled Port1 through
Port5. The RJ-45 jack mates with 8-pin connector and cable assemblies common
to Ethernet 100Base-T applications. Use data quality, shielded, twisted pair
cable.
Pins 1,2,3 and 6 are used. Pins 4,5,7, and 8 are not used. See Figure 3: 5910
Ethernet RJ-45 Connection for pin connections. The Ethernet RJ-45 ports are
MDI/MDIX Auto crossover compatible. The allows the use of straight-through or
cross-over cables.
1 2 3 4 5 6 7 8
RJ-45
1: TD/RD+
2: TD/RD3: RD/TD+
4: nc
5: nc
6: RD/TD7: nc
8: nc
Figure 3: 5910 Ethernet RJ-45 Connection
Power Connections
The 5910 module may be powered in any one of the following ways:

5Vdc applied to the 5910 from the I/O Bus.

11-30Vdc applied to the 5910 on P8.
The 5910 module is for use with Class 2 output power supplies only.
I/O Bus Connection
The 5910 module is normally powered through the connection to the system I/O
Bus. The 5910 module is connected to the system I/O Bus using a cable
connected to P1 or P2. Refer to the System Configuration Guide for complete
information on the system I/O Bus cabling. A jumper link is installed in the bottom
or “Bus power 5V” position on J1.
External Power Connection using an AC adapter
The 5910 Ethernet Switch can be powered using a 12Vdc AC adapter (Schneider
Electric part number: TBUM297240). The AC adapter plugs into a 120Vac supply
and provides 12Vdc to the 5910. A jumper link must be installed in the upper or
“External Power 11-30V” position on J1.

Check that the AC adapter is not connected to the 120Vac supply.
Document (Version 2.27.1.197) 2/24/2017
14
5910 Ethernet Gateway Module

Locate connector P8 on the 5910 module. Refer to Figure 2: 5910 Module
Layout for the location of P8.

The output cable end should be factory installed on a four position removable
terminal block. The negative output connects to pin 1 and the positive output
connects to pin 2. Pins 3 and 4 are not used.

Insert the terminal block into onto connector P8.

Plug the AC adapter into a 120Vac supply.
The 12Vdc adapter connection cannot be used in Hazardous Locations.
External Power Connection using an external power source
The 5910 Ethernet Switch can be powered using 11-30Vdc power source such
as a 24Vdc power supply. A jumper link is installed in the upper or “External
Power 11-30V” position on J1.
A Class 2 power source must be connected to the External Power 11-30Vdc
input on P8.

Check that the power source is off.

Locate connector P8 on the 5910 module. Refer to Figure 2: 5910 Module
Layout for the location of P8.

Connect the power source outputs to the terminal block. The negative output
connects to pin 1 and the positive output connects to pin 2. Pins 3 and 4 are
not used.

Insert the terminal block into onto connector P8.

Turn the power source on.
Configuration Jumpers
The 5910 Ethernet Switch uses a single configuration jumper link for selecting
the input power source.
Jumper
Description
Position
J1
Input power source is from
an AC adapter or external
power source.
Input is 5V from the Bus
on P1 or P2.
Upper or “External Power 11-30V”
J1
Document (Version 2.27.1.197) 2/24/2017
Bottom or “Bus power 5V”
15
5910 Ethernet Gateway Module
LED Indicators
The 5910 module has 11 LEDs to indicate module operation and status. The
SCADAPack controllers cannot disable the power to these LEDs.
LED
Function
Power
On when power is applied to the module. Power source
can be Bus or External.
One LED for each port. On when a link (proper Ethernet
connection) has been established. Flickers when data is
being transmitted or received.
Off for 10 Mbps operation. On for 100 Mbps operation.
Link/Activity
Speed
Document (Version 2.27.1.197) 2/24/2017
16
5910 Ethernet Gateway Module
Operation
The 5910 is a layer 2, five port unmanaged switch. No programming or
configuration is required to use the 5910. Once the Ethernet connections are
made and the 5910 is powered it will begin to operate. Unlike an Ethernet hub
that broadcasts incoming messages to every port, the 5910 Ethernet Switch will
route messages only out of the appropriate port. Both 10BaseT (10 Mbps) and
100BaseTx (100 Mbps) can be used on any of the ports. These ports will
auto0sense the speed and accommodate cross-over or straight-through cables.
Document (Version 2.27.1.197) 2/24/2017
17
5910 Ethernet Gateway Module
Maintenance
This module requires no routine maintenance. If the module is not functioning
correctly, contact Schneider Electric Technical Support for more information and
instructions for returning the module for repair.
Troubleshooting
Condition
Solutions
Power LED is not on.
Check power source. If the input is 5V from
the Bus on P1 or P2 then the J1 jumper
should be in the bottom or “Bus power 5V”
position. If the input is 11-30Vdc from P8
then the J1 jumper should be in the upper
or “External Power 11-30V” position.
Document (Version 2.27.1.197) 2/24/2017
18
5910 Ethernet Gateway Module
Specifications
Disclaimer: Schneider Electric reserves the right to change product
specifications. For more information, visit http://www.schneider-electric.com.
Ethernet switch
type
Ethernet
Terminations
Protocols
Speed and
connection
Broadcast storm
protection
Memory
bandwidth
Full or half
duplex operation
MAC addresses
supported
Ethernet
isolation
Visual Indicators
Input Power
Input Power
Terminations
Dimensions
Mounting
Packaging
Environment
Document (Version 2.27.1.197) 2/24/2017
5 ports, unmanaged, store & forward, 10/100BaseT
RJ45 ports (shielded)
IEEE 802.3, IEEE 802.3u (TBC), IEEE802.3x
Auto-detecting 10/100 Mbps operation
MDI/MDIX Auto crossover (no need for cross-wired
cables)
Yes. 1% of bandwidth.
1.4 Gbps
Full duplex IEEE802.3x and half duplex back pressure
flow control
Dedicated lookup engine with 1K MAC addresses.
Learning, aging and migration.
1500Vrms
Each port - ACT/LINK and 10/100 (Speed).
Power
External Power: 11-30Vdc
1.8W at 12Vdc
2.2W at 30Vdc
Bus Power: 5V at 375mA
4 pole terminal strip and removable terminal block
12 to 22 AWG (0.33 to 3.3 mm²)
4.25 inch (144 mm) wide
4.625 inch (118 mm) high
2.00 inch (51 mm) deep
desktop, rubber feet or 7.5 x 35 DIN rail
corrosion resistant zinc plated steel with black enamel
paint
5% RH to 95% RH, non-condensing
o
o
–40 C to 70 C
o
o
–40 F to 158 F
19
5910 Ethernet Gateway Module
Approvals and Certifications
Safety
Digital
Emissions
Immunity
Declaration
Non-Incendive Electrical Equipment for Use in Class I,
Division 2 Groups A, B, C and D Hazardous Locations.
UL Listed to the following standards:
 CSA Std. C22.2 No. 213-M1987 - Hazardous
Locations.
 CSA Std. C22.2 No. 142-M1987 - Process Control
Equipment.
 UL Std. No. 508 - Industrial Control Equipment.
FCC Part 15, Subpart B, Class A Verification
EN61000-6-4: Electromagnetic Compatibility Generic
Emission Standard Part2: Industrial Environment
C-Tick compliance. Registration number N15744.
EN61000-6-2: Electromagnetic Compatibility Generic
Standards Immunity for Industrial Environments
This product conforms to the above Emissions and Immunity
Standards and therefore conforms with the requirements of
Council Directive 2004/108/EC (as amended) relating to
electromagnetic compatibility and is eligible to bear the CE
mark.
The Low Voltage Directive is not applicable to this product.
Document (Version 2.27.1.197) 2/24/2017
20
Download PDF