levi kitchen faucet installation

SKU(s): 927733, 927734
LEVI KITCHEN FAUCET INSTALLATION
BEFORE YOU BEGIN
We recommend consulting a professional if
you are unfamiliar with installing plumbing
fixtures. Signature Hardware accepts no
liability for any damage to the faucet,
plumbing, sink, counter top, or personal
injury during installation.
Observe all local plumbing and building
codes.
Unpack and inspect the item for shipping
damage. If any damage is found, contact
our Customer Relations team at
1-866-855-2284.
Spout Spring
Hose
TOOLS AND MATERIALS:
Spout Bracket
Plumber’s Tape*
Thread Sealant*
Screwdriver*
Spout
Faucet Body
Adjustable
Wrench*
Escutcheon
Hex Wrench
Basin Wrench*
*not included
Counter Top
Gasket
Locking Washer
GETTING STARTED
Ensure that you have gathered all of the
required materials that are needed for
the installation.
For these instructions, it is assumed that
the old faucet has been completely
removed and any necessary repairs or
modifications to the water supply have
been completed.
Locking Nut
M5 Screw
Braided Water
Supply (cold)
Braided Water Supply (hot)
Check Valve
Levi Kitchen Faucet Installation Instructions
1
LEVI KITCHEN FAUCET INSTALLATION
INSTALLATION
1. Ensure that the water supply below your sink is
completely shut off by turning the shutoff valves all the
way to the right.
3. Remove the lock nut, metal washer, and rubber
gasket from the faucet body. Insert the faucet body
through the mounting hole in your counter top.
Tip: Place a small bucket below your workspace to
catch any water that may drip during the installation
process.
OFF
2. If not already attached, attach the provided braided
water lines to the faucet body. Use the red and blue
marks on the faucet as indicators, and match the hoses
accordingly. Apply a small amount of thread sealant to
the threading on the hoses before attaching. If lines
are already attached, ensure that they are fully
tightenend.
REMOVE
lock nut, metal washer,
rubber gasket
4. From beneath the sink, slide the rubber gasket back
onto the faucet body, followed by the metal washer.
Thread the lock nut back onto the faucet body using a
basin wrench. Finish tightening by turning the two
screws attached to the lock nut to the right.
Apply thread sealant
or plumber’s tape
Levi Kitchen Faucet Installation Instructions
2
LEVI KITCHEN FAUCET INSTALLATION
5. Remove the check valves from the end of each
braided hose on the faucet body. Apply plumber’s tape
or thread sealant to the threading on each check valve
and attach to your main water supply lines. Ensure that
you are connecting the hot and cold lines appropriately.
6. From above the sink, ensure that the set screw on
the back of the faucet body is tight before moving on.
Use the provided hex wrench to tighten.
7. Attach the hose and spout spring to the faucet body.
Apply a small amount of thread sealant, or plumber’s
tape, to the threading on the faucet body before
attaching.
Apply thread
sealant or
plumber’s tape
Tip: The set screw is located just above the faucet
handle, on the back of the valve.
Set screw on back
Levi Kitchen Faucet Installation Instructions
3
LEVI KITCHEN FAUCET INSTALLATION
8. Attach the sprayer to the faucet by threading it onto
the end of the flexible hose. Mount the sprayer into it’s
cradle once attached.
9. Once installation is complete, turn the main water
supply back on from underneath your sink. Check for
any leaks underneath.
ON
10. Remove the aerator from the main faucet spout
using the provided removal tool. Turn the faucet on and
ensure that there are no leaks. Check to ensure that
both hot and cold water are running properly. Allow for
the water to flow for approximately 60 seconds to
remove any dust or sediment within the water lines.
Reattach the aerator and turn on the sprayer. Allow the
sprayer to run for another 60 seconds, and check for
any leaks.
Levi Kitchen Faucet Installation Instructions
4