MR Millenium Logo black box [Converted]

42277 rev6:42288 rev1 08/04/2009 10:24 Page 1
Jet Steam & Jet Stream
ironing system
Please read and keep these instructions
Getting the best from your new ironing system....
Safety first
Caution must be used when handling this appliance as it does get very hot. Always switch off
the unit and allow to cool before cleaning or storing.
Water tank (certain models are illuminated)
The water tank can be removed and re-filled at any time during ironing. Certain Morphy
Richards steam generators have an illuminated water tank. The changing colours enhance the
mood for ironing by creating a colourful atmosphere to help you glide through your washing
basket.
Performance
To extend the performance and life of your steam generator, ensure that you replace the
anti-scale medium regularly.
!
To improve the life of your new product and to ensure the cleanliness of your
clothes, we strongly recommend the use of distilled or demineralised water.
RN42277 MUK Rev 6
If you have a problem or complaint, please call our dedicated UK based helpline
before returning your product to the retailer from where it was purchased.
UK Helpline: 0844 871 0953
Replacement Parts: 0844 873 0719
Ireland Helpline: 1800 409 119
42277 rev6:42288 rev1 08/04/2009 10:24 Page 2
IMPORTANT
SAFETY
INSTRUCTIONS
Personal Safety
•
The use of any electrical
appliance requires the use
of common sense and
strict following of safety
rules.
Primarily there is danger of
injury or death and
secondly the danger of
damage to the appliance.
These are indicated in the
text by the following two
conventions:
•
Do not use the vertical
steam feature on clothes
that are being worn.
•
Do not leave the steam
generator unattended
whilst plugged in or on an
ironing board. Never allow
the mains lead to over
hang the work surface.
•
The mains socket should
always be switched off
before plugging or
unplugging from the
socket. Never yank the
cord to disconnect from
the socket, instead, grasp
the plug and pull to
disconnect.
WARNING: Danger to the
person!
IMPORTANT: Damage to
the appliance!
In addition, we offer the
following safety advice.
Location
•
Do not use outdoors.
•
The steam generator must
be used and rested on a
stable surface.
•
When placing the iron unit
on the base unit or on its
heel, ensure that the
surface on which the heel
or base unit is placed is
stable.
•
Children
•
•
•
2
Children do not understand
the dangers associated
with operating electrical
appliances. Never allow
children to use, or play
with, this appliance.
Close supervision is
necessary when any
appliance is used near
children.
Children should be
supervised to ensure that
they do not play with this
appliance.
UK Helpline 0844 871 0953
Burns can occur from
touching hot metal parts,
hot water or steam. Use
caution when using your
steam generator. If your
iron is placed for a few
moments on the iron rest
plate, this plate may reach
very high temperatures. In
this instance, do not touch
the iron soleplate or the
iron rest plate until the iron
and the iron rest have
cooled down.
This appliance is not
intended for use by
persons (including children)
with reduced physical,
sensory or mental
capabilities, or lack of
experience or knowledge,
unless they have been
given supervision or
instruction concerning the
use of the appliance by a
person responsible for their
safety.
•
Always disconnect the tank
from the base unit when
filling with water and
emptying.
•
Always disconnect the
steam generator from the
electrical supply when
cleaning or when not in
use.
•
If the supply cord is
damaged, it must be
replaced by the
manufacturer, its service
agent or similarly qualified
person(s) in order to avoid
a hazard.
•
Do not operate the steam
generator with a damaged
cord or if the iron has been
dropped or if there are
visible signs of damage or
if it is leaking. To avoid the
risk of electric shock, do
not disassemble the iron or
steam generator, but
telephone Morphy Richards
for advice. Incorrect
reassembly can cause a
risk of electric shock when
the iron is used.
•
If the need arises to
change the mains cable on
your steam generator or
the iron, please return to
Morphy Richards service
department at the address
on the back page.
Special
instructions
•
Has the iron temperature
control been set to the
required temperature? Is
the plug in its socket? Is
the plug itself or the socket
faulty? (Check by plugging
in another appliance).
Other safety
considerations
•
Use the steam generator
only for its intended use.
•
Never hold the generator
base set under the tap.
•
To protect against the risk
of electric shock, do not
immerse the appliance in
water or in any other liquid.
Replacement Parts 0844 873 0719
If your steam generator
does not work, check the
following points:
•
To prevent damage to the
textile being ironed, follow
the temperature guide
carefully. (Test on the inside
of the hem of the garment).
Ireland Helpline 1800 409 119
42277 rev6:42288 rev1 08/04/2009 10:24 Page 3
•
•
•
When ironing is complete,
remove the plug from the
socket, empty any remaining
water from the tank, and allow
to cool before storage.
If you drop or severely knock
your steam generator, this could
cause internal damage even if
the outside appears alright.
Have it checked by a qualified
electrician.
The temperature of accessible
surfaces may be high when the
appliance is operating.
WARNING: Do not use the
product on a surface which
could be damaged by heat or
steam such as a worktop or a
polished wood surface.
If in doubt, contact Morphy
Richards.
ELECTRICAL
REQUIREMENTS
Check that the voltage on the
rating plate of your appliance
corresponds with your house
electricity supply which must be
A.C. (Alternating current).
If the socket outlets in your
home are not suitable for the
plug supplied with this
appliance, the plug should be
removed and the appropriate
one fitted.
WARNING: A damaged or
severed mains cable fitted
with a plug should never be
connected to the mains
supply. It must be destroyed,
as a damaged cable becomes
hazardous if connected to a
power socket.
Should the fuse in the 13 amp
plug require changing, a 13 amp
BS1362 fuse must be fitted.
WARNING: This appliance
must be earthed.
INSTRUCTIONS FOR USE
Temperature guide
Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of
the International Textile Care Labelling Code.
Symbol
(120°C Max) Cool
Control knob
positions
(160°C Max) Warm
(210°C Max) Hot
‘Max setting’
Do not iron
at all
Fabric
Nylon, Acetates
e.g. Acrilan
Courtelle, Orlon
Triacetates, e.g.
Tricel/Polyester
Ironing
Iron on wrong side,
if moisture required
use damp cloth
(Not Acetate)
Wool, Polyester
mixtures e.g.
Polyester/Cotton
Cotton, Linen
Rayon, Rayon
mixtures,
e.g. Rayon/Linen
Fabrics requiring this
setting usually require
steam pressing for heavy
cotton, denim etc.
Steaming
Dry
For details of other Morphy Richards products, please see our website:
3
42277 rev6:42288 rev1 08/04/2009 10:24 Page 4
COMPONENTS OF YOUR STEAM GENERATOR
⁄
fi
‚
„
‰
Â
›
¤
LOCATION
fl
‹
·
‡
COMPONENTS OF
YOUR STEAM
GENERATOR
Iron unit
⁄ Steam trigger
¤ Temperature control knob
Locate the steam generator
horizontally on the iron rest plate
of your ironing board (if large
enough) or on a heat resistant
stand at the same height as
your ironing board or below it.
Always ensure the generator is
on a firm surface when ironing.
WARNING: Do not use the
product on a surface which
could be damaged by heat or
steam such as a worktop or a
polished wood surface.
If in doubt, contact Morphy
Richards.
BEFORE USE
Remove any protective sticker
from the soleplate and the base
unit, if any.
‹ Soleplate
› Temperature indicator light
fi Supply cord from base unit
Base unit
fl Anti-scale cartridge
‡ Water tank
(illuminated on certain models)
Unwind and straighten the
power cord · and supply cord
fi.
Slide out the water tank ‡ and
fill (see filling instructions).
When ironing with the iron
temperature set at 2-dot setting,
the steam output should be set
at the lower end of the steam
range.
· Power cord
‚ Power switch
„ Mode indicator light:
• Appliance off = no lights
• Pre-heating = flashing red light
• Ready to use = green light
• Auto shut-off mode =
flashing red and green light
‰ Replace anti-scale medium
indicator
 Steam level indicators
4
UK Helpline 0844 871 0953
Replacement Parts 0844 873 0719
Textiles and clothes are
supposed to carry ironing
instructions. If they don’t, you
should follow the fabric guide on
page 3, but be sure to test the
temperature by ironing the hem
of the garment or similar area
first.
If you turn the control dial down
from a hot setting to a cooler
setting, wait until the iron
temperature has stabilised
before you continue ironing.
Ireland Helpline 1800 409 119
42277 rev6:42288 rev1 08/04/2009 10:24 Page 5
FILLING
3
Connect the appliance to a
suitable mains outlet, and
switch on the socket. All 5 red
lights will flash once only and a
beep will be heard. Press the
power on switch ‚ and the unit
will turn on, it will default to Max
steam, and the “on” light will
flash red whilst heating up.
When ready for use, the light will
turn green.
4
Press the power switch again to
scroll through steam settings to
the “no steam” position (no
steam lights illuminated). Press
the power switch again to go to
the maximum steam position.
WARNING: Never use battery
topping up fluid or water
containing any substances
like starch or sugar, or
defrosted water from a
refrigerator.
5
Turn the temperature dial on the
iron in a clockwise direction,
select dot-1, dot-2 or dot-3
according to the
recommendation of the garment
label.
Re-install the anti-scale
cartridge and re-position the
water tank on the base unit and
push securely into place. Please
make sure the tank is secure D.
6
The iron’s temperature indicator
light › goes off when the
required temperature is reached.
7
Depress the steam button ⁄ for
1 minute to clear the system of
air (first time use only) which will
be accompanied by a clicking
noise which is quite normal.
8
Begin first time ironing with an
old towel. Note: If you press the
steam button before the steam
generator reaches its required
temperature, a warning double
bleep will sound. It takes about
1 minute to reach the required
temperature.
9
Press the power button ‚ to
choose the steam level from
‘steam off’, ‘low steam’,
‘medium steam’ and ‘maximum
steam’.
1
Place the steam generator on a
stable ironing board or table,
with the iron resting on its stand.
2
Release the detachable water
tank by sliding outwards A.
3
Remove the anti-scale cartridge
by pulling upwards B.
4
Fill the tank to the ‘fill to here’
line with clean tap water C.
IN HARD WATER AREAS, THE
USE OF DISTILLED OR
DEMINERALISED WATER IS
RECOMMENDED.
5
6
Always pour out any remaining
water after use.
Re-filling ‘in use’
1
When the water level becomes
low, the pump begins to emit a
clicking noise. This is due to air
being pumped instead of water
and is quite normal.
Refilling can be done whilst the
appliance is in operation. It is
not necessary to wait for the
appliance to cool down.
2
Slide out the water tank and fill
(see filling instructions).
A
B
C
D
10 The appliance is ready to use.
Steam ironing
1
2
Unwind and straighten the
power cord · and supply cord
fi.
Slide out the water tank and fill
(see filling instructions).
11 Press the steam button ⁄ for
steam ironing.
12 To switch the iron off, turn the
temperature dial on the iron in
an anti-clockwise direction to
‘Min’.
13 Depress and hold the power
switch for 2 seconds, the base
console will beep and switch to
off.
ForHelpline
details of0870
other060
Morphy
products,Parts
please
see157
our 6645
website:Ireland Helpline 1800 409119
UK
2614Richards
Replacement
0870
5
42277 rev6:42288 rev1 08/04/2009 10:24 Page 6
E
Dry ironing
1
Connect the appliance to a
suitable mains outlet.
2
Press the power switch 3 times
until all three steam level
indicators go off (steam off
mode).
3
Turn the temperature dial on the
iron in a clockwise direction,
select dot-1, dot-2, or dot-3
according to the
recommendation of the garment
label.
4
The temperature indicator light
glows on the iron, indicating that
it is switched on.
5
When the required temperature
is reached, the temperature
indicator light on the iron goes
off. The iron is ready to use.
It is always a good idea to begin
with ‘cool’ fabrics and work up
to higher settings.
H
F
How often you need to replace
the medium depends on how
often you use your iron with its
steam functions and how ‘hard’
your water supply is. Water
hardness varies greatly from one
area to another. For advice on
the relative hardness of your
water, contact your local water
supplier.
If, on average, you spend 2
hours per week ironing, then we
suggest you replace your
anti-scale medium as shown in
the table below. If you iron more
or less frequently, then you
should alter the interval between
refills accordingly.
Water
hardness
Refill interval
(months)
An auto-shut off system will
activate if the steam is not used
for over 15 minutes. The mode
indicator light „ will flash
between green and red,
indicating the unit is in ‘sleep
mode’.
When this occurs, press the
steam trigger ⁄ or the power
switch ‚ once. The appliance
will switch on immediately and
you need to select the required
setting.
The anti-scale cartridge is
designed to reduce the build-up
of limescale which occurs
during steam ironing. This will
prolong the working life of your
iron. However, please note that
the anti-scale cartridge will not
completely stop the natural
process of limescale build-up.
6
UK Helpline 0844 871 0953
6
Medium Hard
3
11/2
To obtain replacement anti-scale
refills, telephone our spares
number on: 0844 873 0719.
•
If a new re-fill is not available,
you may continue operating the
appliance but scale will build up
in the system. Replace the antiscale refill as soon as possible.
1
Disconnect the appliance from
the mains outlet.
2
Slide out the tank and remove
the antiscale cartridge E.
3
Pull the plate from the end of
the cartridge F.
4
Remove the foam pad G and
slide out the spent antiscale
sleeve H.
5
Place the refill into the cartridge,
reposition the foam pad and clip
the plate onto the cartridge,
making sure it locks in position.
6
After changing the anti-scale
cartridge, press the anti-scale
button once before replacing the
water tank I.
ANTI-SCALE SYSTEM
I
Soft
Replacement
anti-scale refills
An iron heats up quicker than it
cools down so you’ll save time
and electricity.
Auto-shut off
G
Replacing anti-scale
medium
Replacement
Parts 0844 873 0719
www.morphyrichards.com
Ireland Helpline 1800 409 119
42277 rev6:42288 rev1 08/04/2009 10:24 Page 7
FEATURES OF
YOUR STEAM
GENERATOR
Temperature
indicator light
The indicator light shows
that the iron is warming up.
When the required
temperature is reached, the
light will go out and will
cycle on-off during
operation.
Steam function
During the steaming
process, small amounts of
water may be ejected from
the soleplate. This is normal
and can be avoided by
using the steam for short
amounts of time and only
when the iron is at the
correct temperature (the
indicator light on the iron
goes out when ready).
Sudden jolts of the boiler
unit can also cause water
droplets on the soleplate;
therefore, do not move the
base unit during ironing. We
recommend for the first
time ironing that you iron
over an old towel.
Vertical steam
Hold the iron in a vertical
position between 1cm and
2cm away from the item J.
Press the steam trigger ⁄,
this will create vertical
steam.
This feature is especially
useful for removing creases
from hanging clothes,
curtains, wall hangings, etc.
Emptying and
storing
When you have finished
ironing, unplug your steam
generator.
1
Slide out the water tank
and remove the anti-scale
cartridge K.
2
3
HELPLINE
Empty the water in the tank
by holding it upside down
L.
If you have any difficulty
with your appliance, do not
hesitate to call us.
Replace the anti-scale
cartridge and reinstall the
water tank.
We are more likely to be
able to help than the store
from where you bought it.
Unplug the generator and
leave the iron to cool off for
15 minutes minimum. The
iron must be placed on the
iron rest plate.
The iron and boiler can now
be stored together.
Please have the following
information ready to enable
our staff to deal with your
query quickly.
•
Name of the product
•
MAINTENANCE
Model number and Serial
number as shown on
underside of the appliance.
To clean a stainless steel
soleplate
UK Helpline
0844 871 0953
To keep the soleplate of
your iron clean and free of
limescale, we recommend
that you use one of the
gentle chrome, silver or
stainless steel cleaners that
are generally available.
Always follow the
manufacturer’s instructions.
To clean off melted manmade fibres, set the iron at
3-dot position and pass it
over a clean piece of cotton
which will draw the deposit
off the surface.
Replacement Parts
0844 873 0719
To clean a coated
soleplate
(certain models only)
In the unlikely event of any
man-made fibre fusing to
the soleplate, set the iron at
the 3-dot position and pass
it over a clean piece of
cotton, this will draw the
deposit off the surface.
Do not use scouring
powder or solution, as this
could cause damage to the
coating.
To clean the
exterior
Ireland Helpline
1800 409 119
WEBSITE
You may also contact us
through our website, or visit
the site to browse and
purchase appliances, spare
parts and accessories from
the extensive Morphy
Richards range.
J
K
L
Allow the steam generator
to cool and wipe over with
a damp cloth and mild
detergent, then wipe with a
dry cloth.
ForHelpline
details of0870
other060
Morphy
products,Parts
please
see157
our 6645
website:Ireland Helpline 1800 409119
UK
2614Richards
Replacement
0870
7
42277 rev6:42288 rev1 08/04/2009 10:24 Page 8
YOUR TWO YEAR
GUARANTEE
If, for any reason, this item
is replaced during the 2
year guarantee period, the
guarantee on the new item
will be calculated from the
original purchase date.
Therefore, it is vital to retain
your original till receipt or
invoice to indicate the date
of initial purchase.
It is important to retain the
retailer’s receipt as proof of
purchase. Staple your
receipt to this back cover
for future reference.
Please quote the following
information if the product
develops a fault. These
numbers can be found on
the base of the product.
To qualify for the 2 year
guarantee, the appliance
must have been used
according to the
manufacturer’s instructions.
For example, kettles should
have been regularly
descaled.
Model no.
Serial no.
All Morphy Richards
products are individually
tested before leaving the
factory. In the unlikely event
of any appliance proving to
be faulty within 28 days of
purchase, it should be
returned to the place of
purchase for it to be
replaced.
Subject to the exclusions
set out below (see
Exclusions), the faulty
appliance will then be
repaired or replaced and
dispatched usually within 7
working days of receipt.
The appliance has been
used for hire purposes or
non domestic use.
5
The appliance is second
hand.
6
Morphy Richards are not
liable to carry out any type
of servicing work, under the
guarantee.
7
Plastic filters for all Morphy
Richards kettles and coffee
makers are not covered by
the guarantee.
•
This guarantee does not
confer any rights other than
those expressly set out
above and does not cover
any claims for
consequential loss or
damage. This guarantee is
offered as an additional
benefit and does not affect
your statutory rights as a
consumer.
•
This guarantee is valid in
the UK and Ireland only.
EXCLUSIONS
Morphy Richards shall not
be liable to replace or
repair the goods under the
terms of the guarantee
where:
1
If the fault develops after
28 days and within 24
months of original
purchase, you should
contact the Helpline
number quoting Model
number and Serial number
on the product, or write to
Morphy Richards at the
address shown. You may
be asked to return a copy
of proof of purchase.
4
The fault has been caused
or is attributable to
accidental use, misuse,
negligent use or used
contrary to the
manufacturer’s
recommendations or where
the fault has been caused
by power surges or
damage caused in transit.
2
The appliance has been
used on a voltage supply
other than that stamped on
the products.
3
Repairs have been
attempted by persons other
than our service staff (or
authorised dealer).
For electrical products sold within the
European Community. At the end of the
electrical products useful life, it should
not be disposed of with household
waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice in your
country.
The After Sales Division
Morphy Richards Ltd
Mexborough, South Yorkshire,
England, S64 8AJ
Morphy Richards products are intended for household use only.
Morphy Richards has a policy of continuous improvement in product quality and
design. The company, therefore, reserves the right to change the specification of
its models at any time.
Helplines (office hours)
UK 0844 871 0953
Spare Parts 0844 873 0719
Republic of Ireland 1800 409 119
RN42277 MUK Rev 6 04/09
88
Download PDF