OPERATING INSTRUCTIONS DISHWASHER

EN
OPERATING
INSTRUCTIONS
DISHWASHER
www.gorenje.com
Contents
Front panel ................................................................................................ 2
Safety instructions ..................................................................................... 3
Before washing for the first time ............................................................... 4
Loading the dishwasher ............................................................................ 5
Using the dishwasher ................................................................................ 6
Settings ..................................................................................................... 10
Care and cleaning ..................................................................................... 12
Troubleshooting ........................................................................................ 14
Installation ................................................................................................. 18
Service ...................................................................................................... 21
Information for test institute .......................................................................22
Technical information ................................................................................ 24
Front panel
1
1
2
3
4
5
6
7
2
2
3
Main power switch
Auto wash
Intensive wash
Eco wash
Quick wash
Rinse
SpeedWash
4
5
6
7
8
8
9
10
11
12
13
9
10
Auto open
Extra hygiene
Delayed start
Display
Rinse aid indicator
Salt indicator
11
12 13
Safety instructions
General
Winter storage/transport
•
•
•
•
•
•
•
•
•
•
•
Read the operating instructions and keep them
in a safe place!
Never use the dishwasher for any purpose other
than that specified in these operating instructions.
Do not load the dishwasher door or dishwasher
baskets with anything other than dishes.
Never leave the dishwasher door open as
someone may trip on it.
Use only dishwasher detergent!
This machine can be used by children aged 8
and upwards, and by people with reduced
physical capacity, mental ability, memory loss or
lacking experience and knowledge. These
individuals must be supervised when using the
machine or have instructions on how to use the
machine and understand the risks that can occur.
Cleaning of the machine must not be carried out
by children without supervision.
Children must be watched to ensure they do not
play with the dishwasher.
Damaged mains cables must only be replaced
by a qualified electrician.
Only use the dishwasher in household-type
environments for dishwashing household dishes.
All other use is prohibited.
Never place dishes with solvent residues in the
dishwasher due to the risk of explosion. Nor may
dishes that contain ash, wax or lubricants be
washed in the dishwasher.
WARNING!
•
•
Store the dishwasher where the temperature remains
above freezing.
Avoid long transport distances in very cold weather.
Transport the dishwasher upright or laying on its back.
Overflow guard function
The overflow protection starts pumping out the machine
and turns off the water supply if the water level in the
dishwasher exceeds the normal level. If the overflow
protection is triggered, turn off the water supply and call the
service department.
Packing material
The packaging protects the product during transport. The
packaging material is recyclable. Separate the different
packaging materials to help reduce raw material use and
waste. Your dealer can take the packaging for recycling or
direct you to the nearest recycling centre. The packaging
is comprised of:
•
•
•
•
Corrugated cardboard made from up to 100% recycled
material.
Expanded polystyrene (EPS) with no added chlorine or
fluorine.
Supports made from untreated wood.
Protective plastic made from polyethylene (PE).
Disposal
•
•
•
When the dishwasher has reached the end of its service
life and is to be disposed of, it should immediately be
made unusable. Pull out the power cable and cut it as
short as possible.
The dishwasher is manufactured and labelled for
recycling.
Contact your local authority for information about where
and how your dishwasher should be correctly recycled.
Knives and other pointed items must be placed
with the points down in the cutlery basket or
horizontally in other baskets.
Installation
See the section Installation.
Child safety
•
•
•
Always start the dishwasher immediately after adding
detergent.
Keep children away from the dishwasher when the door
is open. Some detergent may remain inside!
Do not allow children to use or play with the dishwasher.
Be especially vigilant when the door is open.
WARNING!
Children must be supervised – dishwasher detergent is
corrosive!
3
Before washing for the first time
The water softener
In order to achieve good dishwashing results, the
dishwasher needs soft water (water with low mineral
content). Hard water leaves a white coating on dishes and
the dishwasher.
Water hardness is specified using the following scales: The
German water hardness scale (°dH) and the French water
hardness scale (°fH). A water supply with a water hardness
in excess of 6°dH (9°fH) must be softened. This is done
automatically with the aid of the built-in water softener. In
order for the softener to function optimally, it must be
adjusted to the hardness of the water supply.
Contact the local waterworks to check the water hardness
in your area.
Adjusting the water softener
Refill salt indicator
When the salt needs topping up, the above symbol lights
on the display.
When the salt runs out, unscrew the cap and fill the
container with salt. Water is only needed the first time! Wipe
clean and tighten. Run a programme to ensure that any salt
in the dishwasher is rinsed away.
After topping up, it may take a while before the symbol goes
out.
Top up with rinse aid
Drying is faster and a better result is achieved if you use
rinse aid. You will also achieve a better dishwashing result
with clear and spotless dishes.
1
Open the rinse aid compartment lid.
2
Carefully top up with rinse aid. Only add rinse aid to the
level marked max.
Fill up the salt
3
Before you begin using a dishwasher with a water softener,
you must fill the salt compartment with salt for the water
supply to be softened automatically. Use large grain salt or
special dishwasher salt.
Wipe up any splashes of rinse aid around the
compartment.
4
Close the lid firmly.
Chapter Settings on page 10 describes how to adjust the
water softener.
Press to open
WARNING!
In order to avoid rust stains a dishwashing programme
must be started immediately after adding salt.
Never pour dishwasher detergent into the salt
compartment. This destroys the water softener!
Do as follows the first time:
1 Unscrew the lid as illustrated.
2
Place the funnel supplied with the dishwasher in the salt
compartment top-up hole. First, pour in about 1 l of
water.
3
Then add salt, a maximum of 1.5 kg, until the
compartment is full.
4
Wipe up any excess salt so that the lid can be screwed
on firmly.
5
Run a programme to ensure that any salt in the
dishwasher is rinsed away.
Refill rinse aid indicator
When the rinse aid needs topping up, the above symbol
lights on the display.
After topping up, it may take a while before the symbol goes
out.
Setting the rinse aid dosage
The section Settings describes how to set the rinse aid
dosage. Rinse aid dispensing can be set from 0 (Off) to 5
(High dose). (Factory settings: 5)
Decrease the rinse aid dosage:
• If the dishes have a sticky white/blue film.
• If the dishes are streaked.
• Build-up of foam. If you have very soft water, the rinse
aid can be diluted 50:50 with water.
Salt compartment lid
4
Loading the dishwasher
Energy-efficient dishwashing
•
•
•
•
•
Do not start the dishwasher until it is fully loaded to save
energy.
Do not rinse under running water. Simply scrape off
large food particles before loading the dishwasher.
Choose an environmentally-friendly detergent. Read the
environmental declaration on the packaging!
If the dishes are only slightly dirty, you can select a
programme with a low temperature.
Better drying results are achieved if you use the Auto
open option, which automatically opens the dishwasher
door at the end of the programme. (If the dishwasher is
built-in the surrounding furnishings must be resistant to
any condensation.)
Fragile dishes
Some cookware is not dishwasher safe. This can be for
several reasons. Some materials cannot withstand strong
heat, others can be damaged by dishwashing detergent.
Exercise caution with, for example, handmade items, fragile
decoration, crystal/glassware, silver, copper, tin, aluminium,
wood and plastic. Look for the "Dishwasher safe" marking.
Raising and lowering the upper basket
1 Pull out the upper basket.
2
Grab the sides of the upper basket with both hands and
lift it up.
3
Repeatedly lift the basket with both hands to change its
position. (The upper basket can be set in three
positions.) When the upper basket is in the highest
position lifting it will return it to the lowest position. Note
that both sides of the basket must always be set to the
same height.
The dishwasher's baskets
The dishwasher is equipped with an upper basket and a
lower basket with a cutlery basket.
Upper basket
Place glasses, cups, bowls, side plates and saucers in the
upper basket. All dirty surfaces should face inwards and
downwards! Wine glasses are placed on the wine glass
shelf and knives are placed in the knife stand on the right
(if fitted).
Lower basket
Place plates, side plates, serving dishes, pots and cutlery
(in the cutlery basket) in the lower basket.
5
Using the dishwasher
Foldable tines
Fold down the foldable tines (plate supports) when
dishwashing pots. Release the foldable tines by pressing
the catch inwards before adjusting their position.
Cutlery basket
Place cutlery with the handles facing down, except for
knives, and spread them out as much as possible. Ensure
that spoons do not stack inside each other.
Place the cutlery basket in the lower basket.
Points to consider
•
•
•
•
All dirty surfaces should face inwards and downwards!
Dishes should not be placed in or on each other.
Angle dishes with hollows, such as cups, so that the
rinse water will run off. This is also important for plastic
items.
Make sure small items cannot fall through the
dishwasher basket; place them in the cutlery basket.
NOTE!
Check that the spray arms can rotate freely.
Add detergent
Press to open
1
Prewash detergent compartment
2
Main wash detergent compartment
Detergent is added according to water hardness.
Follow the instructions on the detergent packaging. This
dishwasher is fitted with a water softener, so use detergent
and rinse aid doses suitable for soft water.
Too much detergent can result in less effective dishwashing
and also entails greater environmental impact.
The detergent compartment must be dry when adding
detergent. There is one compartment for the prewash and
one for the main wash. If powder or liquid dishwasher
detergent is used, add a small amount of the detergent to
the prewash compartment. Contact the detergent
manufacturer if you have questions about the detergent.
NOTE!
Use only dishwasher detergent! Washing up liquid must
not be used as the foam that forms prevents the
dishwasher from operating effectively.
Dishwasher tablets
Halve the tablet if it is difficult to close the dispenser lid.
There is a risk that the detergent will not be released
properly if the lid is tight and will not open correctly.
NOTE!
Dishwasher tablets are not recommended for short
programmes (less than 75 minutes). Use powder or liquid
dishwasher detergent instead.
3-in-1/All-in-one detergent
Chapter Settings describes how to activate TAB (3-in-1/
All-in-one detergent). Note that salt must be put in the salt
compartment. If you are not satisfied with the dishwashing
or drying results, deactivate the setting TAB (3-in-1/
All-in-one detergent) and top up with salt, detergent and
rinse aid. See Chapter Before washing for the first time.
Read through the directions for these products carefully. If
anything is unclear, contact the detergent manufacturer.
6
The main power switch
Press and hold the main power switch until the display turns
on. Also check that the water tap is on.
PROGRAMS - Choose programme
Choose a programme to suit the type of dishes and how
dirty they are.
Press the desired programme until the programme symbol
is activated.
Auto wash
The dishwasher can measure how dirty the dishes are and
adjust water consumption and temperature accordingly.
When newly installed, the programme needs to be run five
times before it is fully adapted and can provide the best
results.
Auto wash 1) +
SpeedWash +
Auto open
An effective programme for daily use for slightly dried
leftovers. (This programme is not intended for burnt food,
such as on oven dishes.)
Intensive wash
Programme for very dirty dishes, such as pans, casserole
dishes and oven dishes. If these dishes do not completely
fill the dishwasher, you can add plates and the like.
Eco wash
This programme is intended for cleaning normally dirty
dishes and is the most effective programme in terms of
combined energy and water consumption.
Quick wash
This programme is used for glasses and porcelain that is
slightly dirty, such as coffee cups.
In combination with SpeedWash, a shorter programme is
achieved (15 minutes).
programmes and some options cannot be combined
(available options glow dimly).
SpeedWash
This option shortens the programme time, but uses more
energy and water.
Auto open
The dishwasher door opens automatically at the end of the
programme, which improves the drying results. (If the
dishwasher is built-in the surrounding furnishings must be
resistant to any condensation.)
NOTE!
The dishwasher door must not be blocked when set to
open automatically. This can disrupt door lock
functionality.
Extra hygiene
This option is intended for situations where demands on
hygiene are especially high, such as when dishwashing
baby bottles and cutting boards. The temperature is
increased in both the main wash and the final rinse.
Delayed start
When you select Delayed start the dishwasher will start
1-24 hours after you close the door.
1
Press the button once to activate Delayed start. Press
the button several times – or hold it in – to set the
desired number of hours.
2
Close the door and the dishwasher counts down 1 hour
at a time and starts after the selected delay.
If you want to cancel the Delayed start option, open the door
and press and hold the main power switch until the display
turns off.
Starting the dishwasher
Close the door to start the dishwasher. If the main power
switch is on the dishwasher will start automatically when
the door is closed.
TIME - Time remaining
Once you have chosen a programme and options, the time
the programme took when last used is displayed.
Rinse
Used to rinse dishes while you wait for the dishwasher to
become fully loaded.
Once you have started the dishwasher the display shows
the remaining programme time. The remaining time is
updated after the water for the final rinse has been heated.
EXTRA - Selecting Options
This may differ somewhat from time to time depending on
the temperature of the water supply, the amount of dishes,
the ambient temperature and other factors.
To select an option, press one of the option buttons until
the option is activated. The available options vary between
1)
This combination (Auto wash + SpeedWash + Auto open) is also known as QuickIntensive (90 minutes).
7
Front display
Unloading the dishwasher
Hot porcelain is more fragile. Leave the dishes to cool in
the dishwasher before unloading them.
Unload the lower basket first to avoid any water drops from
the upper basket falling onto the dishes in the lower basket.
Dishwashing
Time remaining
Drying
Stopping or changing a programme
If you want to change programme after starting the
dishwasher, open the door then press and hold the main
power switch until the display turns off. Add more detergent
if the lid of the detergent dispenser has opened. Then press
the main power switch, choose a new programme and close
the door.
Do you want to add more dishes?
Open the door. The dishwasher stops automatically. Add
the dishes and close the door. After a while, the dishwasher
continues the programme.
If the dishwasher is turned off due to a
power failure
If the dishwashing programme was not finished, the
interrupted programme continues when power is restored.
NOTE!
During drying, the programme is interrupted if the power
is cut or the door is open for more than 2 minutes.
How to get the best drying results
•
•
•
•
•
Fully load the dishwasher.
Angle dishes with hollows, such as cups, so that the
rinse water will run off. This is also important for plastic
items.
Top up with rinse aid or increase the rinse aid dosage
level.
Activate the Auto open option.
Allow the dishes to cool before unloading the
dishwasher.
Once the programme has finished
Once the programme has finished, "End" appears on the
display.
At the end of the programme one short signal will sound.
Chapter Settings describes how to change this function.
The dishwasher switches off automatically after the
programme ends. Shut off the water tap after each use.
8
9
10 / 25
--- / 25
--- / 10
--- / ---
Intensive wash
Eco wash 2)
Quick wash
Rinse
2)
1)
--- / 25
Auto wash
1
2
1-3
Prewashes
35 °C
55 °C
70 °C
50-65 °C
Main wash
1
1
2
2
2-3
Number of
rinses
--- °C
25 °C
53 °C
70 °C
65 °C
Final rinse
0:07
0:20
3:00
2:55
2:10-2:50
Dishwashing
time
(approx.
hrs:min)
0.01
0.2
0.92
1.7
0.9-1.5
Energy
(approx.
kWh)
1)
3
10
9.5
17
11-20
Water cons.
(L)
Consumption values
Consumption values vary depending on the temperature of the incoming water, room temperature, load size, selected additional functions and more.
This dishwashing programme is the standard cleaning cycle used to compile the energy labelling information. It is intended for washing normally dirty
dishes and is the most effective programme in terms of combined energy and water consumption.
Auto open
Auto open
Detergent,
EXTRA
compartment - Options
1/2
(ml)
PROGRAMS
- Programme
Programme chart
Settings
Open the settings menu:
+
1. First, open the door. Turn off the machine. Press and hold the main power switch until the display
lights up.
2. Within 10 seconds:
- press the programme button for Auto wash and the option button for SpeedWash.
3. The display shows the settings menu (current setting and its currently set value).
(Exit the menu by browsing through the menu or pressing the main power switch.)
Navigate the settings menu:
Press to browse between setting values.
Press to save the set value and continue to the next
setting.
Current setting.
Current setting value.
You can now adjust the following settings:
Settings
Options
1. Rinse aid
1:00 - 1:05
Rinse aid dosage setting.
Increase the rinse aid dosage:
• If the dishes have water marks.
Decrease the rinse aid dosage:
• If the dishes have a sticky white/blue film.
• If the dishes are streaked.
• Build-up of foam. If you have very soft water, the
rinse aid can be diluted 50:50 with water.
2. Water hardness
2:00 - 2:09
Adjusting the water softener. Read off the appropriate
setting from the water hardness table below.
°dH
°fH
°dH
°fH
0-5
0-9
20-24
35-43
6-8
10-14
25-29
44-52
9-11
15-20
30-39
53-70
12-14
21-25
40-49
71-88
15-19
26-34
50+
89+
Do not forget to put salt in the salt compartment after
you have set the water softener to 2:01 - 2:09.
For a water supply with a hardness under 6°dH (9°fH),
select 2:00. The water softener is deactivated and no
salt is needed.
10
Settings
Options
3. TAB
3:00 (Off)
(3-in-1/all-in-one detergent) 3:01 (On)
You can activate this setting when using 3-in-1/
All-in-one detergent. The dishwashing programmes
automatically adapt to provide the best possible
dishwashing and drying results every time. If this setting
is activated there is no need to add rinse aid since this
option disables rinse aid dispensing. It also reduces the
amount of salt added to the water softener. Note that
salt must be put in the salt compartment.
NOTE!
In order to achieve good dishwashing results, it is
essential to check which type of detergent or
all-in-one product best suits your needs! Read the
detergent packaging carefully for information on
proper use. Always follow the directions for use or
information on the detergent packaging!
4. Buzzer volume
4:00 - 4:03
The dishwasher uses a buzzer to indicate when a
programme is finished or when a fault has occurred.
5. Self-cleaning programme
5:00 (Off)
5:01 (On)
Self-cleaning programme for hygienic cleaning of the
dishwasher tub, spray arms and spray pipes.
This programme can be run (with no dishes in the
machine) using normal dishwasher detergent, citric acid
or one of the dishwasher cleaners available on the
market. For the removal of limescale deposits see also
the section The dishwasher tub in the chapter Care and
cleaning.
Start the programme by activating the setting and then
closing the door.
11
Care and cleaning
Coarse filter
Spray arms
The coarse filter traps larger food particles, which cannot
get past the drainage pump. Empty the coarse filter as
necessary.
Holes and bearings can sometimes become blocked.
Remove any debris using a pin or the like. The spray arms
also have holes underneath.
Coarse filter
1
Lift the coarse filter by the handle.
2
Empty the coarse filter. Remember to replace it!
To facilitate cleaning you can remove the spray arms.
Remember to fit them firmly back into place afterwards.
Lower spray arm
• Pull the lower spray arm straight up to release it.
Fine filter
Debris that collects on the fine filter is automatically rinsed
away during each wash. Clean the fine filter when
necessary.
Fine filter
1
Turn the handle anticlockwise.
2
Lift the filter straight up using the handle. Free the coarse
filter to clean the fine filter.
3
Replace in reverse order. Check that the edges seal
properly when replacing the fine filter.
4
Lock the filter in place by turning the handle clockwise
to the stop position. The handle should point straight
out from the dishwasher.
Upper spray arm
1 Pull out the upper basket.
2
Unscrew the spray arm bearings counterclockwise to
remove the spray arm from the upper basket.
NOTE!
The dishwasher must not be used without the filters in
place!
Dishwashing results may be affected if the coarse filter is
incorrectly fitted.
The door and the door seal
Regularly clean the sides of the door and the door seal. Use
a slightly damp cloth (with a little cleaner if necessary).
The dishwasher tub
The dishwasher tub is made of stainless steel and is kept
clean through normal use.
Limescale deposits
If you have hard water, limescale deposits may build up in
the dishwasher. If this happens, run a self-cleaning
programme with two tablespoons of citric acid in the
detergent compartment (with no dishes in the machine).
12
The chapter Settings describes how to activate the
Self-cleaning programme setting.
NOTE!
Do not forget to replace the drainage pump stop.
Front panel
Keep the buttons clean and free from grease. Wipe them
clean with a dry or slightly damp cloth. Never use cleaners
– they can scratch the surface. Use the main power switch
to turn off the dishwasher before cleaning the buttons to
avoid activating any buttons unintentionally.
Unblocking the inlet hose filter
If the water supply contains small particles, the outer filter
on the inlet hose may become blocked, which results in
Water inlet fault.
Unblocking the drainage pump
1
If the dishwasher still contains water after the programme
has finished, something may be blocking the drainage pump.
Such items are easily removed.
Turn off the machine using the main power switch and
unplug it from the wall socket.
2
Turn off the water tap.
3
Unscrew the inlet hose.
1
Turn off the machine using the main power switch and
unplug it from the wall socket.
4
Carefully remove the outer filter from the inlet hose and
clean it.
2
Remove the coarse filter and the fine filter.
5
3
Scoop out the water from the dishwasher tub.
Replace the filter and check that the gasket is correctly
positioned.
4
In order to inspect the drainage pump, remove the
coloured stop on the right in the bottom drain.
6
Screw the inlet hose firmly into place.
7
Plug the machine into the wall socket and turn on the
water tap. Allow the pressure to settle for a while and
check that the connection is watertight.
5
Turn the pump wheel located behind the drainage pump
stop by hand. Carefully remove any items.
6
Replace the drainage pump stop along with the fine and
coarse filters.
7
Plug the machine in again.
Outer filter on inlet
hose
If the dishwasher still does not start and a whirring sound
is heard, the overflow protection has been activated.
Gasket
•
•
•
Shut off the water.
Remove the plug from the wall socket.
Call the service department.
Drainage pump stop
13
Troubleshooting
Type of fault on the display
Action
F10
Overfilling
Clear the drainage pump. See the section Care and cleaning. If the problem
persists, call the service department.
F11
Water outlet fault
See “Water remains in the dishwasher” in the table “Problem” below. If the problem
persists, call the service department.
F12
Water inlet fault
Check that the water tap is on. If the problem persists, call the service department.
F40
Inlet valve leakage
Turn off the water tap and call the service department.
F52
Water level fault
Check that the drainage hose is fitted in accordance with the installation
instructions. If the problem persists, call the service department.
F54
Overfilling
Turn off the water tap and call the service department.
F56
Circulation fault
Call the service department.
Press any button to clear the error message.
Problem
Possible causes
Action
The buttons do not react when pressed. You have pressed the buttons too soon Wait a moment then try again.
after opening the door.
Cannot close door.
The buttons are dirty.
Clean with a dry or slightly damp cloth.
The door is closed.
Open the door. The buttons only react
to use when the door is open.
The baskets are not correctly positioned. Check that the baskets are correctly
positioned horizontally.
Check that the dishes are not blocking
the baskets from sliding properly into
place.
The door lock does not click into place
and lock.
14
Check the door lock. If it does not click
into place and lock, open the door. Press
and hold the button for the Auto open
option for 15 seconds. Then wait 30
seconds. Close the door. Check that the
door lock clicks into place and locks.
Problem
Possible causes
Action
The dishwasher does not start.
The door is not properly closed.
Check.
You have opened the dishwasher to add Close the door and wait. After a while,
more dishes while a programme is in
the dishwasher continues the
progress.
programme.
The door lock has not clicked into place Check the door lock. If it has not clicked
and locked.
into place and locked, open the door.
Press and hold the button for the Auto
open option for 15 seconds. Then wait
30 seconds. Close the door. Check that
the door lock clicks into place and locks.
A fuse/circuit breaker has been tripped. Check.
The plug is not plugged into the wall
socket.
Check.
The water tap is turned off.
Check.
Overflow/leaks.
Check.
A whirring sound (the drainage pump) Turn off the water tap. Pull out the plug
is heard from the dishwasher and does and call the service department.
not stop when the main power switch is
turned off.
Check that the Delayed start option has Press and hold the main power switch
not been selected.
until the display turns off if you want to
cancel the Delayed start option. Restart
the dishwasher.
The dishes are not clean.
The spray arms do not rotate.
Remove the arms and clean them.
Check that the dishes are not blocking
the spray arms.
Old detergent. Detergent is a perishable Avoid large packages.
product.
Spots on stainless steel or silver.
Incorrect detergent dosage.
Dose according to water hardness. Far
too much or far too little detergent results
in poorer dishwashing results.
Unsuitable dishwashing programme.
Choose a longer programme.
Dishes loaded incorrectly.
Do not cover porcelain with large bowls
or the like. Avoid placing very tall
glasses in the corners of the baskets.
Glasses and cups have toppled over
during the programme.
Place dishes to sit steady.
The filter is not correctly fitted.
Screw the filter firmly into place. See the
section Care and cleaning.
Some foodstuffs, such as mustard,
Rinse off these types of foodstuffs if not
mayonnaise, lemon, vinegar, salt and starting the dishwasher immediately.
dressings, can mark stainless steel if left Why not use the Rinse programme.
for too long.
All stainless steel can cause spots on
silver if they come into contact during
dishwashing. Aluminium can also cause
spots on dishes.
In order to avoid marks and tarnishing,
separate dishes made from different
metals, such as silver, stainless steel
and aluminium.
15
Problem
Possible causes
Action
Spots or films on the dishes.
The water softener is leaking salt.
Check that the salt compartment lid is
properly tightened. Otherwise call the
service department.
Incorrect water softener setting.
See the section Settings.
Incorrect rinse aid dosage setting.
See the section Settings.
Salt compartment empty.
Top up with salt. See the section Before
washing for the first time.
3-in-1/ All-in-one detergent is used and Inactivate the setting TAB (3-in-1/
the setting TAB (3-in-1/ All-in-one
All-in-one detergent) and top up salt and
detergent) is activated.
rinse aid.
Too high temperature and/or too much Wash crystal at a low temperature and
detergent can cause etching on crystal. with a conservative amount of detergent.
Unfortunately, this cannot be repaired, Contact the detergent manufacturer.
only prevented.
The dishes have a sticky white/blue film. Rinse aid dosage setting too high.
Spots left after washing.
Lipstick and tea can be difficult to wash Use a detergent with a bleaching agent.
off.
Detergent residue in the detergent
compartment after dishwashing.
The detergent compartment was damp The detergent compartment must be dry
when adding detergent.
when adding detergent.
Rattling sound when dishwashing.
The dishes are not correctly placed or
the spray arms are not rotating.
Check that the dishes are placed
securely. Spin the spray arms to make
sure they can rotate.
1 minute appears in the display.
The programme is taking longer than
estimated.
No action. The programme time is stored
and next time the programme is run the
corrected time will be displayed.
Water remains in the dishwasher.
The filters are blocked.
Clean the coarse and fine filters.
Debris in the drainage pump.
Clean the drainage pump. See the
section Care and cleaning.
Kink in drainage hose.
Check that the hose is free from kinks
and sharp bends.
Blocked drainage hose.
Disconnect the drainage hose where it
connects to the sink unit's water trap.
Check that no debris has fastened and
that the connection has an inner
diameter of at least 14 mm.
Dirt around the seals and in corners.
Clean with washing-up brush and low
foaming cleaner.
Low temperature programmes have
been selected for a prolonged period.
Run a programme with a higher
temperature about once a month.
Bad odour in dishwasher.
16
Reduce the amount. See the sections
Before washing for the first time and
Settings. If you have very soft water, you
may want to dilute the rinse aid 50:50
with water.
Problem
Possible causes
Action
The dishes are not dry enough.
The Auto open option is not activated.
Activate the Auto open option.
The dishwasher is not fully loaded.
Fully load the dishwasher.
Rinse aid needs topping up or dosage
is set too low.
Top up with rinse add or increase the
rinse aid dosage. See the sections
Before washing for the first time and
Settings.
3-in-1/ All-in-one detergent is used and Inactivate the setting TAB (3-in-1/
the setting TAB (3-in-1/ All-in-one
All-in-one detergent) and top up salt and
detergent) is activated.
rinse aid.
17
Installation
[mm]
1214
596
30
575
720
670
123-173
718
848- 898
85
600
52
51
Nominal dimensions. Actual measurements may vary.
Safety instructions
•
•
•
•
•
Connections to electricity, water and drainage must be
performed by a qualified professional.
Always follow applicable regulations for water, drainage
and electricity.
Take care during installation! Wear protective gloves!
There must always be two people!
Place a drip tray on the floor beneath the dishwasher to
prevent damage from any water leaks.
Before screwing the dishwasher into place, test the
dishwasher by running the Rinse programme. Check
that the dishwasher fills with water and drains. Check
also that none of the connections leak.
WARNING!
Turn off the water supply when installing the dishwasher!
WARNING!
The plug must be disconnected or power to the socket
turned off while the work is carried out!
18
Transport protection for the door
Do not forget to remove the transport protection for the door
when unpacking the dishwasher.
REMOVE
Placing the dishwasher
The dishwasher is intended for freestanding installation, but
can also be installed under a worktop.
Adjust the height and slide the dishwasher
into place
•
24 mm
Freestanding
1 Make sure the area on which the dishwasher is to be
installed is firm. Adjust the dishwasher's height using
the four feet so that the dishwasher is level. The
dishwasher may lean no more than 5 mm.
2
Once the feet are properly adjusted, tighten the anti-tip
feet firmly against the floor.
Check that the machine is installed such that the
door opens freely, otherwise door lock functionality
may be disrupted.
6
Make any final adjustments to the front feet (the
dishwasher may lean no more than 5 mm).
7
Once the feet are properly adjusted, tighten the anti-tip
feet firmly against the floor.
The dishwasher can also be installed in a recess without
its worktop. See Remove dishwasher worktop.
Attach the plinth
(Packed inside the dishwasher.)
Anti-tip feet
Built-in
1 Start by measuring the height from the floor to the
bottom edge of the worktop.
2
Measure the height from the floor to the top edge of the
dishwasher.
3
Adjust the dishwasher's feet by turning them clockwise
to raise or anticlockwise to lower the machine.
4
Check that there is an air gap of at least 3 mm between
the underside of the worktop and the top edge of the
dishwasher.
5
Slide the dishwasher into place.
•
•
Drainage connection
min.
14 mm
Pull through the drainage and supply hoses when
the machine is slid into place.
Check that the hoses have no kinks or sharp bends,
and check that there is nothing that can damage the
hoses.
19
Connection to water supply
Use only the inlet hose supplied with the dishwasher. Do
not re-use old or other spare hoses.
The supply pipe must be fitted with a water tap (stopcock).
The water tap must be easily accessible, so that the water
can be shut off if the dishwasher has to be moved.
Once the installation is complete, turn on the water tap and
allow the pressure to settle for a while. Check that all
connections are watertight.
Connection to cold water supply
Connect the dishwasher to the cold water supply if the
building is heated using oil, electricity or gas.
350--950 mm
min. 350 mm
The drainage hose may be extended by a maximum of 3 m
(the total length of the drainage hose must not exceed 4.5
m). Any joins and connecting pipes must have an internal
diameter of at least 14 mm. However, the drainage hose
should ideally be replaced with a new hose without joins.
No part of the drainage hose may be more than 950 mm
above the bottom of the dishwasher. The hose must not be
routed directly to a floor drain or the like. In such cases, the
hose can act as a siphon and empty the dishwasher.
The hose must always discharge at least 350 mm above
the bottom of the machine.
Ensure that the drainage hose has no kinks.
NOTE!
Do not exceed the permitted water supply temperature.
Certain materials used in some cookware cannot
withstand strong heat. See Fragile dishes in the chapter
Loading the dishwasher.
Electrical connection
Information about the electrical connection can be found on
the serial number plate. This specification must match the
electricity supply.
The dishwasher must be connected to an earthed socket.
NOTE!
When the drainage hose is routed to a connection nipple
on the sink unit's water trap (see illustration 1), please
note that the hose must be attached at the same height
as the underside of the sink unit, otherwise dishwater from
the sink may flow back into the dishwasher. For other
connection alternatives, see illustrations 2 and 3.
1
Connection to hot water supply
Connect the dishwasher to the hot water supply (max. 70
°C) if the building is heated using an energy-efficient means
such as district heating, solar power or geothermal power.
Choosing a hot water connection cuts dishwashing times
and reduces the dishwasher's energy consumption.
2
3
The electric wall socket must be placed outside of the
installation area to be easily accessible after installing the
dishwasher. Do not use an extension cord!
NOTE!
Repairs and maintenance relating to safety or
performance must be carried out by a qualified
professional.
Remove dishwasher worktop
The dishwasher can be installed in a recess without its
worktop. If the dishwasher's worktop is removed, the
dishwasher must be installed so that it is enclosed on both
sides and is under a separate worktop. If the dishwasher is
installed so that one of the sides is visible, a brace must be
20
Service
fitted to the rear edge of the dishwasher. Accessories can
be purchased where you bought the dishwasher.
3
2
Read the chapter Troubleshooting before contacting the
service department. If you have encountered a problem that
you cannot resolve, please contact your nearest dealer, see
www.gorenje.com.
When making contact, provide the details on the serial
number plate. Include the article number (1) and the serial
number (2).
1
ART. NO.
2x
SERIAL NO.
1
2
For recess installation, see the section Placing the
dishwasher.
21
Information for test institute
Request test institute information via e-mail
dishwashers@appliance-development.com.
The request should include the details on the serial number
plate. Include the article number (1) and the serial number
(2).
22
ART. NO.
SERIAL NO.
1
2
Your notes
23
Technical information
Information on energy labelling
Information sheet, in compliance with Commission Delegated Regulation (EU) No. 1059/2010
Gorenje
Model designation:
GS65260
Number of standard place settings:
13 1)
Energy efficiency class:
A++
Annual energy consumption(AEC):
262 kWh per year 2)
Energy consumption of the standard cleaning cycle(Et):0.92 kWh
Power consumption
0.49 W
Off-mode (Po):
0.49 W
Left-on mode (Pl):
Annual water consumption (AWC):
Drying efficiency class:
Standard programme:
Programme time for the standard cleaning cycle:
Duration of the left-on mode (Tl):
Noise emissions:
2660 litres per year 3)
A 4)
Eco wash 5) , option Auto open
180 minutes
Infinite
47 dB(A) re 1 pW
1)
In accordance with standard, EN 50242.
2)
Based on 280 standard cleaning cycles with a cold water connection and consumption in accordance with energy saving mode. The actual
energy consumption depends on how the machine is used.
3)
Based on 280 standard cleaning cycles. The actual water consumption depends on how the machine is used.
4)
On a scale from G (least efficient) to A (most efficient).
5)
This dishwashing programme is the standard cleaning cycle used to compile the energy labelling information. It is intended for washing
normally dirty dishes and is the most effective programme in terms of combined energy and water consumption.
Technical data
1)
24
Weight can vary due to different specifications.
www.gorenje.com
en (01-17)
Art. No.: 543657. Rev. 04. We reserve the right to make changes.
Height:
848-898 mm
Width:
600 mm
Depth:
596 mm
Weight:
55 kg 1)
Water pressure:
0.03–1.0 MPa
Electrical connection:See serial number plate
Rated power:
See serial number plate
Download PDF