Server User Guide RS520-E8-RS8 V2 RS520-E8-RS12-EV2

RS520-E8-RS8 V2
RS520-E8-RS12-EV2
Server User Guide
E10402
First Edition
May 2015
Copyright © 2015 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means,
except documentation kept by the purchaser for backup purposes, without the express written permission
of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not
limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no
event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental,
or consequential damages (including damages for loss of profits, loss of business, loss of use or data,
interruption of business and the like), even if ASUS has been advised of the possibility of such damages
arising from any defect or error in this manual or product.
Specifications and information contained in this manual are furnished for informational use only, and are
subject to change at any time without notice, and should not be construed as a commitment by ASUS.
ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual,
including the products and software described in it.
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
ii
Contents
Notices....................................................................................................................... vii
REACH .......................................................................................................vii
Safety information..................................................................................................... viii
Australia statement notice................................................................................ix
About this guide........................................................................................................... x
Chapter 1: Product Introduction
1.1
System package contents.......................................................................... 1-2
1.2
Serial number label..................................................................................... 1-3
1.3
System specifications................................................................................ 1-4
1.4
Front panel features.................................................................................... 1-6
1.5
Rear panel features..................................................................................... 1-7
1.6
Internal features.......................................................................................... 1-9
1.7
LED information........................................................................................ 1-11
1.7.1
Front panel LEDs....................................................................... 1-11
1.7.2
LAN (RJ-45) LEDs..................................................................... 1-12
1.7.3
HDD status LED......................................................................... 1-12
Chapter 2: Hardware Information
2.1
Chassis cover.............................................................................................. 2-2
2.2
Central Processing Unit (CPU).................................................................. 2-3
2.2.1
2.3
2.4
2.5
Installing the CPU........................................................................ 2-3
System memory.......................................................................................... 2-9
2.3.1
Overview...................................................................................... 2-9
2.3.2
Memory Configurations................................................................ 2-9
2.3.3
Installing a DIMM....................................................................... 2-11
2.3.4
Removing a DIMM..................................................................... 2-11
Hard disk drives........................................................................................ 2-12
2.4.1
Installing a 3.5-inch HDD........................................................... 2-12
2.4.2
Installing a 2.5-inch SSD (RS520-E8-RS12-EV2 only).............. 2-13
Expansion slot........................................................................................... 2-15
2.5.1
Installing an expansion card to the PCI-E slot........................... 2-15
2.5.2
Installing an ASUS PIKE II card (RS520-E8-RS8 only)............. 2-17
2.5.3
Installing an M.2 expansion card............................................... 2-21
2.5.4
Installing a Mezzanine card....................................................... 2-22
2.5.5
Configuring an expansion card.................................................. 2-24
2.6
Cable connections.................................................................................... 2-25
2.7
Backplane cabling.................................................................................... 2-26
iii
Contents
2.8
Removable/optional components............................................................ 2-28
2.8.1
System fans............................................................................... 2-28
2.8.2 Slim optical drive (optional, for RS520-E8-RS8 V2 only)........... 2-29
2.8.3
Redundant power supply module.............................................. 2-31
Chapter 3: Installation Options
3.1
Tool-less Friction Rail Kit........................................................................... 3-2
Chapter 4: Motherboard Information
4.1
Motherboard layout..................................................................................... 4-2
4.2Jumpers....................................................................................................... 4-4
4.3
Internal connectors..................................................................................... 4-8
4.4
Onboard LEDs........................................................................................... 4-18
Chapter 5: BIOS Setup
5.1
5.2
5.3
5.4
iv
Managing and updating your BIOS........................................................... 5-2
5.1.1
ASUS CrashFree BIOS 3 utility................................................... 5-2
5.1.2
ASUS EZ Flash 2 Utility............................................................... 5-3
5.1.3
BUPDATER utility........................................................................ 5-4
BIOS setup program................................................................................... 5-6
5.2.1
BIOS menu screen....................................................................... 5-7
5.2.2
Menu bar...................................................................................... 5-7
5.2.3
Menu items.................................................................................. 5-8
5.2.4
Submenu items............................................................................ 5-8
5.2.5
Navigation keys............................................................................ 5-8
5.2.6
General help................................................................................ 5-8
5.2.7
Configuration fields...................................................................... 5-8
5.2.8
Pop-up window............................................................................ 5-8
5.2.9
Scroll bar...................................................................................... 5-8
Main menu................................................................................................... 5-9
5.3.1
System Date [Day xx/xx/xxxx]...................................................... 5-9
5.3.2
System Time [xx:xx:xx]................................................................ 5-9
Advanced menu........................................................................................ 5-10
5.4.1
ACPI Settings............................................................................. 5-11
5.4.2
Smart Settings........................................................................... 5-11
5.4.3
NCT6779D Super IO Configuration........................................... 5-12
5.4.4
Intel LAN I210 Configuration...................................................... 5-13
5.4.5
Serial Port Console Redirection................................................. 5-14
Contents
5.5
5.4.6
APM........................................................................................... 5-17
5.4.7
PCI Subsystem Settings............................................................ 5-18
5.4.8
Network Stack Configuration..................................................... 5-19
5.4.9
CSM Configuration..................................................................... 5-20
5.4.10
Trusted Computing.................................................................... 5-21
5.4.11
USB Configuration..................................................................... 5-22
5.4.12
iSCSI Configuration................................................................... 5-23
IntelRCSetup menu................................................................................... 5-24
5.5.1
Processor Configuration............................................................ 5-25
5.5.2
Advanced Power Management Configuration........................... 5-27
5.5.3
Common RefCode Configuration............................................... 5-28
5.5.4
QPI Configuration...................................................................... 5-29
5.5.5
Memory Configuration................................................................ 5-30
5.5.6
IIO Configuration........................................................................ 5-33
5.5.7
PCH Configuration..................................................................... 5-34
5.5.8
Miscellaneous Configuration...................................................... 5-38
5.5.9
Server ME Configuration............................................................ 5-38
5.5.10
Runtime Error Logging Support................................................. 5-39
5.6
Server Mgmt menu.................................................................................... 5-39
5.7
Event Logs menu...................................................................................... 5-44
5.7.1
Change Smbios Event Log Settings.......................................... 5-44
5.7.2
View Smbios Event Log............................................................. 5-45
5.8
Monitor menu............................................................................................ 5-46
5.9
Security menu........................................................................................... 5-47
5.10
Boot menu................................................................................................. 5-50
5.11
Tool menu.................................................................................................. 5-51
5.12
Exit menu................................................................................................... 5-52
Chapter 6: RAID Configuration
6.1
Setting up RAID........................................................................................... 6-2
6.1.1
RAID definitions........................................................................... 6-2
6.1.2
Installing hard disk drives............................................................. 6-3
6.1.3
Setting the RAID item in BIOS..................................................... 6-3
6.1.4
RAID configuration utilities........................................................... 6-3
6.2LSI Software RAID Configuration Utility .................................................. 6-4
6.2.1
Creating a RAID set..................................................................... 6-5
6.2.2
Adding or viewing a RAID configuration.................................... 6-11
6.2.3
Initializing the virtual drives........................................................ 6-12
v
Contents
6.2.4
Rebuilding failed drives.............................................................. 6-16
6.2.5
Checking the drives for data consistency.................................. 6-18
6.2.6
Deleting a RAID configuration.................................................... 6-21
6.2.7
Selecting the boot drive from a RAID set................................... 6-22
6.2.8
Enabling WriteCache................................................................. 6-23
6.3Intel® Rapid Storage Technology enterprise SATA Option
ROM Utility................................................................................................. 6-24
6.4
6.3.1
Creating a RAID set................................................................... 6-25
6.3.2
Deleting a RAID set................................................................... 6-27
6.3.3
Resetting disks to Non-RAID..................................................... 6-28
6.3.4
Exiting the Intel® Rapid Storage Technology enterprise SATA
Option ROM utility...................................................................... 6-29
6.3.5
Rebuilding the RAID.................................................................. 6-29
6.3.6
Setting the Boot array in the BIOS Setup Utility......................... 6-31
Intel® Rapid Storage Technology enterprise (Windows)....................... 6-32
6.4.1
Creating a RAID set................................................................... 6-33
6.4.2
Changing a Volume Type.......................................................... 6-35
6.4.3
Deleting a volume...................................................................... 6-36
6.4.4
Preferences................................................................................ 6-37
Chapter 7: Driver Installation
7.1
RAID driver installation.............................................................................. 7-2
7.1.1
Creating a RAID driver disk......................................................... 7-2
7.1.2
Installing the RAID controller driver............................................. 7-4
7.2
Management applications and utilities installation............................... 7-14
7.3
Running the Support DVD ....................................................................... 7-14
7.4Intel® chipset device software installation............................................. 7-18
7.5
Installing the Intel® I350-AM1/I350-AM2/I210 X540-BT2 Gigabit
Adapters driver.......................................................................................... 7-20
7.6
VGA driver installation............................................................................. 7-23
7.7Intel® Rapid Storage Technology enterprise 4.0 installation................ 7-25
Appendices
ASUS contact information....................................................................................... A-2
vi
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of shielded cables for connection of the monitor to the graphics card
is required to assure compliance with FCC regulations. Changes or modifications to this
unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
This Class A digital apparatus complies with Canadian ICES-003.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of
Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS
REACH website at http://csr.asus.com/english/REACH.htm.
vii
Safety information
Electrical Safety
•
Before installing or removing signal cables, ensure that the power cables for the system
unit and all attached devices are unplugged.
•
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
•
When adding or removing any additional devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are connected. If
possible, disconnect all power cables from the existing system before you add a device.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your dealer.
Operation Safety
•
Any mechanical operation on this server must be conducted by certified or experienced
engineers.
•
Before operating the server, carefully read all the manuals included with the server package.
•
Before using the server, ensure all cables are correctly connected and the power cables
are not damaged. If any damage is detected, contact your dealer as soon as possible.
•
To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots,
sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.
This product is equipped with a three-wire power cable and plug for the user’s safety. Use
the power cable with a properly grounded electrical outlet to avoid electrical shock.
Lithium-Ion Battery Warning
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
CD-ROM Drive Safety Warning
CLASS 1 LASER PRODUCT
Heavy System
CAUTION! This server system is heavy. Ask for assistance when moving or carrying
the system.
viii
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
Australia statement notice
From 1 January 2012 updated warranties apply to all ASUS products, consistent with
the Australian Consumer Law. For the latest product warranty details please visit http://
support.asus.com. Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
If you require assistance please call ASUS Customer Service 1300 2787 88 or visit us at
http://support.asus.com
ix
About this guide
Audience
This user guide is intended for system integrators, and experienced users with at least basic
knowledge of configuring a server.
Contents
This guide contains the following parts:
1.
Chapter 1: Product Introduction
This chapter describes the general features of the server, including sections on front
panel and rear panel specifications.
2.
Chapter 2: Hardware Information
This chapter lists the hardware setup procedures that you have to perform when
installing or removing system components.
3.
Chapter 3: Installation Options
This chapter describes how to install optional components into the barebone server.
4.
Chapter 4: Motherboard Information
This chapter gives information about the motherboard that comes with the server. This
chapter includes the motherboard layout, jumper settings, and connector locations.
5.
Chapter 5: BIOS Information
This chapter tells how to change system settings through the BIOS Setup menus and
describes the BIOS parameters.
6.
Chapter 6: RAID Configuration
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
7
Chapter 7: Driver Installation
This chapter provides instructions for installing the necessary drivers for different
system components.
x
Conventions
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when
trying to complete a task.
CAUTION: Information to prevent damage to the components when
trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text
Indicates a menu or an item to select.
Italics <Key> Used to emphasize a word or a phrase.
Example: <Enter> means that you must press
the Enter or Return key.
<Key1>+<Key2+<Key3>
If you must press two or more keys simultaneously, the key names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<Del>
Command
Means that you must type the command
exactly as shown, then supply the required
item or value enclosed in brackets.
Example: At the DOS prompt, type the
command line: format A:/S
Keys enclosed in the less-than and greater-than sign means that you must press the enclosed key.
References
Refer to the following sources for additional information, and for product and software
updates.
1.
ASUS Server Web-based Management (ASWM) user guide
This manual tells how to set up and use the proprietary ASUS server management
utility.
2.
ASUS websites
The ASUS websites worldwide provide updated information for all ASUS hardware and
software products. Refer to the ASUS contact information.
xi
xii
Chapter 1: Product Introduction
Product Introduction
This chapter describes the motherboard features and the new
technologies it supports.
1
1.1
System package contents
Check your system package for the following items.
Model Name RS520-E8-RS12-EV2
RS520-E8-RS8 V2
Chassis
ASUS F 2U Rackmount Chassis
ASUS 2U Rackmount Chassis
Motherboard ASUS Z10PR-D16 Server Board
Component
1 x 770W Redundant Power Supply
1 x 770W Redundant Power Supply
12 x Hot-swap 3.5-inch HDD Trays
8 x Hot-swap 3.5-inch HDD Trays
2 x Hot-swap 2.5-inch SSD Trays
1 x SATA/SAS back panel
1 x SATA/SAS back panel
1 x Front I/O Board
1 x Front I/O Board
4 x System Fans (80 mm x 38 mm)
1 x Front USB Board
1xP
ower sharing Board
4 x System Fans (80 mm x 38 mm)
1 x Air duct
1xP
ower sharing Board
1 x Air duct
Accessories
1 x Support DVD
1 x Support DVD
1 x ASWM* Enterprise DVD
1 x ASWM* Enterprise DVD
1 x ASMB8 DVD
1 x ASMB8 DVD
2 x Bag of Screws
1 x Bag of Screws
2 x AC Power Cable
2 x AC Power Cable
2xC
PU Heatsink (Quantity may vary 2 x CPU Heatsink (Quantity may
depending on the request of each
vary depending on the request of
area/country)
each area/country)
Optional
Items
1 x Tool-less Friction Rail Kit
1 x Tool-less Friction Rail Kit
Additional 770W Redundant Power
Supply
1 x Slim DVD
Additional 770W Redundant Power
Supply
*ASUS System Web-based Management
If any of the above items is damaged or missing, contact your retailer.
1-2
Chapter 1: Product Introduction
1.2
Serial number label
Before requesting support from the ASUS Technical Support team, you must take note of the
product’s serial number containing 12 characters such as xxS0xxxxxxxx shown as the figure
below. With the correct serial number of the product, ASUS Technical Support team members
can then offer a quicker and satisfying solution to your problems.
RS520-E8-RS8 V2
xxS0xxxxxxxx
RS520-E8-RS12-EV2
xxS0xxxxxxxx
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
1-3
1.3
System specifications
The ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2 is a 1U barebone server system
featuring the ASUS Z10PR-D16 Server Board. The server supports Intel® LGA2011-3 Intel®
Xeon® E5-2600 Processor v3 plus other latest technologies through the chipsets onboard.
RS520-E8-RS12-EV2
Model Name
RS520-E8-RS8 V2
2 x Socket R3 LGA 2011-3 Intel® Xeon® Processor E5-2600 v3
Processor Support / System Family
Bus
QPI 6.4 / 8.0 / 9.6GT/s
Core Logic
Memory
Intel® C612 PCH Chipset
Total Slots
16 (4 Channels per CPU, 8 DIMMS per CPU)
Capacity
Maximum up to 1024 GB
Memory Type
DDR4 2133 / 1866 / 1600 / 1333 RDIMM / LR-DIMM/ NVDIMM
Refer to www.asus.com for the latest memory AVL update.
32GB, 16GB, 8GB and 4GB (RDIMM)
Memory Size
64GB, 32GB (LRDIMM)
Refer to www.asus.com for the latest memory AVL update.
Total PCI/PCI-E
3+1
Slots
Low-profile
Expansion
Slots (follow
SSI Location #) Slot Type
1 x PCI-E Gen3 x16 (x8 link)
2 x PCI-E Gen3 x8 (x8 link)
1 x PCI-E Gen3 x8 (x8 Gen3 link) (for OCP Mezzanine*)
* Supports MCB-10G series (10 Gigabit/s series Gigabit Ethernet LAN
card) (Optional)
Intel® C612
9 x SATA 6 Gbps ports (8 x 2 mini-SAS connectors)
1 x discrete M.2 socket
SATA Controller Intel® RSTe (for Windows only; supports software RAID 0, 1, 10
and 5)
LSI® MegaRAID driver supports RAID 0, 1 and 10) (for Linux
and Windows)
Storage
ASUS PIKE II 3008 8-port SAS
HBA card
Optional items:
ASUS PIKE II 3008 8-port
SAS HBA card
SAS Controller ASUS PIKE II 3108 8-port SAS
HW card
(Default with ASUS HBA/RAID
card)
HDD Bays
System Fans
I = internal
A or S = hotswappable
ASUS PIKE II 3108 8-port
SAS HW RAID card
12 x Hot-swap 3.5-inch HDD
Bays
8 x Hot-swap 3.5-inch HDD
Bays
2 x Hot-swap 2.5-inch SSD
Bays
4 x System Fan (80 mm x 38 mm)
(continued on the next page)
1-4
Chapter 1: Product Introduction
Model Name
RS520-E8-RS12-EV2
RS520-E8-RS8 V2
®
Networking
LAN
Graphic
VGA
2 x Intel I210T + 1 x Management LAN
1 x Mezzanine 10G dual port LAN card
Aspeed AST2400 32MB
2 x RJ-45 GbE port
1 x RJ-45 management port
Onboard I/O Connectors / LED
2 x USB 3.0 ports
indicators
1 x VGA port
1 x PS/2 keyboard/mouse combo port
Windows® Server 2012 R2
Windows® Server 2012
Windows® Server 2008 R2
RedHat® Enterprise Linux
CentOS
OS Support
Unbuntu
VMWare
Citrix XenServer
* Support versions are subject to change without notice.
Refer to www.asus.com for updates.
Management
Solution
Software
ASWM Enterprise
Out of Band
Remote
Management
ASMB8-iKVM for KVM-over-Internet
Dimension (HH x WW x DD)
Net Weight Kg
(CPU, DRAM & HDD not
included)
Power Supply
Power Rating
615 mm x 444 mm x 88 mm
Environment
Non operation temperature: -40°C – 70°C
23 Kg
1+1 renundant 770W 80PLUS Gold Power Supply
100-127/200-240VAC, 10A/5A, 50-60Hz, Class I
Operating temperature: 10°C – 35°C
Non operation humidity: 20% – 90% (Non condensing)
*Specifications are subject to change without notice.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
1-5
1.4
Front panel features
The barebone server displays a simple yet stylish front panel with easily accessible features.
The power and reset buttons, LED indicators, and USB ports for each Node are located on
the front panel.
Refer to the 1.7.1 Front panel LEDs section for the LED descriptions.
Turn off the system power and detach the power supply before removing or replacing any
system component.
RS500-E8-RS8 V2
Reset button
Location button
2 x USB 3.0 ports
Power button
Slim optical drive (optional)
VGA port
Refer to 1.7 LED information
4
HDD Bay 1
HDD Bay 2
HDD Bay 5
HDD Bay 3
HDD Bay 6
3
2
1
HDD Bay 4
HDD Bay 7
HDD Bay 8
RS520-E8-RS12-EV2
Refer to 1.7 LED information
HDD Bay 2
HDD Bay 1
USB 2.0 ports
Location button
Power button
HDD Bay 5
HDD Bay 9
1-6
HDD Bay 4
HDD Bay 3
HDD Bay 6
HDD Bay 10
HDD Bay 7
HDD Bay 8
HDD Bay 11
Reset button
HDD Bay 12
Chapter 1: Product Introduction
1.5
Rear panel features
4
3
2
1
The rear panel includes the expansion slots, system power sockets, and rear fans. The I/O
shields with openings for the rear panel connectors on the motherboard are also placed in the
rear panel.
RS520-E8-RS8 V2
PS/2 keyboard/mouse cpmbo port
LAN port 2
Serial port (optional)
Mezzanine 10G dual-port LAN card (optional)
DM management LAN port*
Redundant power supply
Power connector
VGA port
2 x USB 3.0 ports
LAN port 1
RS520-E8-RS12-EV2
2.5-inch SSD Bay 2
2.5-inch SSD Bay 1
PS/2 keyboard/mouse cpmbo port
VGA port
LAN port 2
Redundant power supply
Power connector
Serial port (optional)
Mezzanine 10G dual-port LAN card (optional)
DM management LAN port*
2 x USB 3.0 ports
LAN port 1
*
This port is for ASUS ASMB8-iKVM controller and for technicians only.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
1-7
Asset tag
The Asset tag is a simple but useful device that is conveniently located on the front panel of
the server that you can pull out or easily slide back in. It has a piece of paper that allows you
to write down important information about the server.
RS520-E8-RS8 V2
RS520-E8-RS12-EV2
1-8
Chapter 1: Product Introduction
1.6
Internal features
The barebone server includes the basic components as shown.
RS520-E8-RS8 V2
2
3
6
1
6
6
1.
Redundant power supply
2.
Power supply fan
3.
ASUS Z10PR-D16 Server Board
4.
SATA/SAS back panel
5.
Slim optical drive (optional)
6.
System fans
7.
Asset Tag
8.
Hot-swap 3.5-inch HDD Bay
6
4
8
5
7
Turn off the system power and detach the power supply before removing or replacing any
system component.
The barebone server does not include a floppy disk drive. Connect a USB floppy disk drive
to any of the USB ports on the front or rear panel if you need to use a floppy disk.
*WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
1-9
RS520-E8-RS12-EV2
2
3
1
6
6
6
1.
Redundant power supply
2.
Hot-swap 2.5-inch SSD Bay
3.
ASUS Z10PR-D16 Server Board
4.
SAS back panel
5.
Front USB I/O panel
6.
System fans
7.
Front LED panel
8.
Asset Tag
9.
Hot-swap 3.5-inch HDD Bay
6
4
9
5 8
7
Turn off the system power and detach the power supply before removing or replacing any
system component.
The barebone server does not include a floppy disk drive. Connect a USB floppy disk drive
to any of the USB ports on the front or rear panel if you need to use a floppy disk.
*WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY
1-10
Chapter 1: Product Introduction
1.7
LED information
1.7.1
Front panel LEDs
RS520-E8-RS8 V2
RS520-E8-RS12-EV2
LAN4 LED (for Mezzanine card)
Power button with LED
LAN3 LED (for Mezzanine card)
LAN2 LED
Message LED
Location button with LED
LAN1 LED
Message LED
LAN1 LED
HDD Access LED
4
3
2
LAN2 LED
1
HDD Access LED
Location button with LED
LAN3 LED (for Mezzanine
card)
Power button with LED
LED
Icon
Display
status
LAN4 LED (for Mezzanine card)
Description
Power LED
ON
System power ON
HDD
Access
LED
OFF
No activity
Blinking Read/write data into the HDD
Message
LED
OFF
System is normal; no incoming event
ON
With the onboard ASMB8-iKVM: a hardware monitor event is
indicated
OFF
No LAN connection
Blinking LAN is transmitting or receiving data
ON
LAN LEDs
3
1
2
LAN connection is present
Blinking LAN is transmitting or receiving data
4
RESET
3
Location
LED
ON
Location switch is pressed
OFF
Normal status (Press the location switch again to turn off)
4
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
1-11
1.7.2
LAN (RJ-45) LEDs
SPEED LED
ACT/LINK LED
SPEED LED
ACT/LINK LED
ACT/LINK LED
SPEED LED
Status
Description
Status
Description
OFF
GREEN
BLINKING
No link
Linked
Data activity
OFF
ORANGE
GREEN
10 Mbps connection
100 Mbps connection
1 Gbps connection
1.7.3
HDD status LED
HDD status LED
HDD activity LED
HDD LED Description
Power ON (HDD detected)
RAID disk has failed and should be
RED
swapped immediately (Error detected
in the installed HDD)
Blinking GREEN/RED
RAID rebuilding
OFF
No HDD installed
Blinking GREEN
Read/write data from/to HDD
GREEN
HDD Status LED
HDD Activity LED
1-12
Chapter 1: Product Introduction
Chapter 2: Hardware Information
Hardware Information
This chapter lists the hardware setup procedures that you have
to perform when installing or removing system components.
2
2.1
Chassis cover
2.1.1
Removing the rear cover
1.
4
3
2
1
Loosen the two thumbscrews on the rear panel to release the rear cover from the
chassis. There is no need to remove the thunbscrews, just loose them.
Screws
2.
Firmly hold the rear cover and slide it towards the back panel for about half an inch to
the front cover.
Front cover side thumbscrew
3.
Remove the rear cover
from the chassis.
The chassis is covered
with a layer of film.
Before starting up the
system, remove the film
to avoid overheating.
2-2
Chapter 2: Hardware Information
2.2
Central Processing Unit (CPU)
The motherboard comes with two surface mount LGA 2011-3 sockets designed for the Intel®
Xeon E5-2600 v3 processor family.
Ensure that all power cables are unplugged before installing the CPU.
2.2.1
•
Upon purchase of the motherboard, ensure that the PnP cap is on the socket and
the socket contacts are not bent. Contact your retailer immediately if the PnP cap
is missing, or if you see any damage to the PnP cap/socket contacts/motherboard
components. ASUS shoulders the repair cost only if the damage is shipment/transitrelated.
•
Keep the cap after installing the motherboard. ASUS will process Return Merchandise
Authorization (RMA) requests only if the motherboard comes with the cap on the LGA
2011-3 socket.
•
The product warranty does not cover damage to the socket contacts resulting from
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP
cap.
Installing the CPU
To install a CPU:
1. There is a screw at the left corner on the illustration below to secure the air duct (the
three spots beside are for the position of the air duct). Remove the screw with a Philip
screw driver and then remove the air duct.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-3
2.
Locate the CPU socket on the motherboard.
Before installing the CPU, ensure that the socket box is facing toward you and the triangle
mark is on the lower-left position.
Triangle mark
3.
Press the right load lever down (A) then move it to the left (B) until it is released from
the retention tab (C).
Load lever
2-4
Chapter 2: Hardware Information
4.
Press the left load lever (D), move it to the right (E) until it is released from the retention
tab (F), then gently pull it until it is fully extended.
5.
Gently push the right load lever down to slightly lift the load plate (G).
Do not insert the load lever into the retention tab.
6.
Hold the edge then gently lift the load plate (H).
edge of the Load plate
Load plate
Load lever
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-5
7.
Get the CPU.
8. Align and position the CPU over the socket ensuring that the triangle mark on the CPU
matches the triangle mark on the socket box.
9.
Install the CPU into the slot.
The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to
prevent bending the CPU pins on the socket.
Triangle mark
10
2-6
Gently push the load plate just enough to let it sit on top of the CPU.
Chapter 2: Hardware Information
11. Push the left load lever down (I) ensuring that the edge of the load plate is fixed and
tucked securely under the lever (J), then the PnP cap will eject automatically.
PnP cap
12. Push the right load lever down (K) ensuring that the edge of the load plate is fixed and
tucked securely under the lever (L), then insert the right load lever under the retention
tab (M).
edge of load plate
Load lever
Retention tab
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-7
13. Apply some Thermal Interface Material
to the exposed area of the CPU that the
heatsink will be in contact with.
•
Ensure that the Thermal Interface
Material is spread in an even thin
layer.
•
Some heatsinks come with
pre-applied Thermal Interface
Material. If so, skip this step.
The Thermal Interface Material is toxic and inedible. DO NOT eat it. If it gets into your eyes
or touches your skin, wash it off immediately, and seek professional medical help.
14. Install the heatsink according to the illustrations below.
15. Recover the air duct when the CPU and DIMMs are installed.
2-8
Chapter 2: Hardware Information
2.3
System memory
2.3.1Overview
The motherboard comes with sixteen (16) Double Data Rate 4 (DDR4) Dual Inline Memory
Modules (DIMM) sockets.
The figure illustrates the location of the DDR4 DIMM sockets:
2.3.2
Memory Configurations
You may install 4 GB, 8 GB, 16 GB, and 32 GB RDIMMs or 32 GB, 64 GB LR-DIMMs and
NVDIMM into the DIMM sockets using the memory configurations in this section.
•
Always install DIMMs with the same CAS latency. For optimum compatibility, it is
recommended that you obtain memory modules from the same vendor.
•
Start installing the DIMMs in slots A2 or B2.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-9
Single CPU configuration
You can refer to the following recommended memory population for a single CPU configuration.
Single CPU configuration (must be installed on CPU1)
DIMM
A2
1 DIMM
1 DIMM
2 DIMMs
4 DIMMs
8 DIMMs
A1
B2
B1
C2
C1
D2
D1
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Dual CPU configuration
You can refer to the following recommended memory population for a dual CPU configuration.
Dual CPU configuration
A2
2 DIMMs
4 DIMMs
8 DIMMs
12 DIMMs P
16 DIMMs P
2-10
A1
P
P
P
P
P
B2
P
P
DIMM (CPU1)
B1 C2 C1
P
P
P
P
P
P
P
P
DIMM (CPU2)
D2
D1
P
P
P
P
E2
P
P
E1
P
P
P
P
P
F2
F1
P
P
P
P
P
P
G2
G1
P
P
P
P
H2
H1
P
P
P
P
Chapter 2: Hardware Information
2.3.3
Installing a DIMM
Ensure to unplug the power supply before adding or removing DIMMs or other system
components. Failure to do so may cause severe damage to both the motherboard and the
components.
1.
Unlock a DIMM socket by pressing
the retaining clips outward.
2.
Align a DIMM on the socket such that
the notch on the DIMM matches the
DIMM slot key on the socket.
DIMM notch
DIMM slot key
Unlocked retaining clip
A DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into
a socket in the wrong direction to avoid damaging the DIMM.
3.
Hold the DIMM by both of its ends
then insert the DIMM vertically into
the socket. Apply force to both ends
of the DIMM simultaneously until the
retaining clips snaps back into place.
Ensure that the DIMM is sitting firmly
on the DIMM slot.
Locked Retaining Clip
Always insert the DIMM into the socket VERTICALLY to prevent DIMM notch damage.
2.3.4
Removing a DIMM
1.
Simultaneously press the retaining
clips outward to unlock the DIMM.
2.
Remove the DIMM from the socket.
Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM
might get damaged when it flips out with extra force.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-11
2.4
Hard disk drives
The system supports 8 (RS520-E8-RS8 V2) or 12 (RS520-E8-RS12-EV2) hot-swap 3.5-inch
SATAII/SAS hard disk drives. Two hot-swap 2.5-inch hard disk drives are supported on the
rear panel of RS520-E8-RS12-EV2. The hard disk drive installed on the drive tray connects
to the motherboard SATAII/SAS ports via SATAII/SAS backplane.
2.4.1
Installing a 3.5-inch HDD
To install a 3.5-inch HDD:
1.
Press the spring lock to release to the
tray lever.
2.
Firmly hold the tray lever then pull the
drive tray out of the bay.
1
2
2-12
3.
Slide the HDD into the drive tray with
the SATA port facing towards the back
of the expansion slot.
Ensure that the screw holes on the
HDD matches the screw holes on the
tray.
4.
Secure the HDD in the HDD tray with four
screws (two on each side).
Spring lock
Tray lever
Chapter 2: Hardware Information
5.
Insert the drive tray and HDD assembly
all the way into the depth of the bay ( A
) and push the tray lever until it clicks
and secures the drive tray in place ( B
). The drive tray is correctly placed when
its front edge aligns with the bay edge.
B
A
When installed, the SATA II/SAS connector on the drive connects to the SATA II/SAS
interface on the backplane.
6.
Repeat steps 1 to 5 to install other 3.5-inch SATA II/SAS HDDs.
2.4.2
Installing a 2.5-inch SSD (RS520-E8-RS12-EV2 only)
To install a 2.5-inch SSD:
1.
Press the spring lock to release the tray lever.
Tray lever
Spring lock
2.
Firmly hold the tray lever then pull the
drive tray out of the bay.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-13
3.
Release the screws on each side of the
drive tray to release the drive tray metal
beam.
4.
Orient and place the SSD into the tray.
Ensure that the SSD is fitted firmly inside the drive tray and that the four screws of the
SSD matches the four screws holes of the drive tray.
support beam
SSD screw hole
Drive tray screw hole
5.
Carefully insert the drive tray and push it all the way to the depth of the bay ( A ).
Lock the secure tab to secure the drive tray in place ( B ).
B
A
When installed, the connector on the drive connects to the connector on the backplane.
6.
2-14
Repeat steps 1 to 5 to install other 2.5-inch SSDs.
Chapter 2: Hardware Information
2.5
Expansion slot
The barebone server comes with two riser card brackets allowing you to install Low-Profile
PCI Express expansion cards.
The steps below are only for RS520-E8-RS8 V2.
2.5.1
Installing an expansion card to the PCI-E slot
To install an expansion card:
1.
Remove two screws on the bracket and
put it aside.
2.
Remove the screws that secure the
metal cover to the chassis.
3.
Remove the metal cover then set it aside
for future use.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-15
2-16
4.
Insert the expansion card into the PCI-E
slot. Ensure that the golden fingers are
totally inserted into the slot. Secure it
with the screws removed before.
5.
Reinstall the bracket. Secure it with two
screws to complete the installation.
Chapter 2: Hardware Information
2.5.2
Installing an ASUS PIKE II card (RS520-E8-RS8 only)
You can install an ASUS PIKE II card on the provided PCI-E slot onboard.
To install an ASUS PIKE II card:
1.
Remove the default cable from the motherboard and the backplane.
2.
Remove two screws on the bracket and put it aside.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-17
2-18
3
Remove the bracket and remove the screws that secure the metal cover to the chassis.
4.
Remove the metal cover then set it aside for future use.
Chapter 2: Hardware Information
5. Prepare your ASUS PIKE II card.
6. Insert the expansion card into the PCI-E slot. Ensure that the golden fingers are totally
inserted into the slot.
7. Secure the ASUS PIKE II card with the screw removed before and reinstall the bracket,
then connect the two mini-SAS HD cables to the ASUS PIKE II card.
connect to ASUS PIKE II
connector 2
connect to ASUS PIKE II
connector 1
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-19
8.
Secure the bracket with the two bracket screws removed before.
9. Connect connector 1 on the ASUS PIKE II card to connector 1 on the backplane and
connector 2 on the ASUS PIKE II card to connector 2 on the backplane using two miniSAS HD cables.
Backplane connector 1
Backplane connector 2
2-20
Chapter 2: Hardware Information
2.5.3
Installing an M.2 expansion card
You can install an M.2 expansion card on the provided M.2 slot onboard.
To install an M.2 expansion card:
1.
Remove the screw on the M.2 socket and put it aside.
2. Prepare your M.2 expansion card.
3. Align and insert the M.2 card into the M.2 slot onboard as shown.
4. Secure the M.2 card with a screw to complete the installation.
•
Please pay attention when removing the screw, the stand screw might be removed
together with it.
•
Ensure that the M.2 card is positioned between the screw and the stand screw before
securing it.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-21
2.5.4
Installing a Mezzanine card
You can install a supported Mezzanine card on the onboard slot.
To install a Mezzanine card:
1. Remove the slot bay from the Mezzanine
card expansion slot.
2. Prepare your Mezannine card and the signal cable. Connect the signal transmission
end (white) to the AUXLED_CON header on the card.
AUXLED_CON1
3. 2-22
Match and insert the four (4) screw holes on the Mezzanine card into the four (4) stand
screws on the chassis, then insert the Mezzanine card to the slot on the motherboard.
Chapter 2: Hardware Information
4. Secure the Mezzanine card with the four (4) bundled screws.
5. Connect the signal end (black) to the OCP_LED1 header on the motherboard.
OCP_LED1
The two ends of the signal cable are different in size and color for easy recognition. Please
refer to your exact cable.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-23
2.5.5
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.
Turn on the system and change the necessary BIOS settings, if any. See Chapter 5 for
information on BIOS setup.
2.
Assign an IRQ to the card. Refer to the following tables.
3.
Install the software drivers for the expansion card.
Standard Interrupt assignments
IRQ
Priority
Standard function
0
1
System Timer
1
2
Keyboard Controller
2
-
Programmable Interrupt
3*
11
Communications Port (COM2)
4*
12
Communications Port (COM1)
5*
13
--
6
14
Floppy Disk Controller
7*
15
--
8
3
System CMOS/Real Time Clock
9*
4
ACPI Mode when used
10*
5
IRQ Holder for PCI Steering
11*
6
IRQ Holder for PCI Steering
12*
7
PS/2 Compatible Mouse Port
13
8
Numeric Data Processor
14*
9
Primary IDE Channel
15*
10
Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-24
Chapter 2: Hardware Information
2.6
Cable connections
3
•
The bundled system cables are pre-connected before shipment. You do not need
to disconnect these cables unless you need to remove pre‑installed components to
install additional devices.
•
Refer to Chapter 4 for detailed information on the connectors.
1
6
7
2
4
3
3
3
3
3
5
3
3
4
5
Standard cables connected to the motherboard
1.
2.
3.
4.
5.
6.
7.
24-pin ATX power connector (from power supply to motherboard)
8-pin 12V power connector (from power supply to motherboard)
System fan connector (from system fan to motherboard)
USB connector (from motherboard to front I/O board)
SATA ports connectors (system default; from motherboard to SATA/SAS backplane)
System auxiliary panel connector (from motherboard to front I/O board)
System panel connector (from motherboard to front I/O board)
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-25
2.7
Backplane cabling
RS520-E8-RS8 V2
connect to the 8-pin
power connector
connect to mini-SAS HD connectors 1 and 2 on the backplane. With
two mini-SAS HD cables connected, a total number of 8 SAS/SATA
HDDs can be supported (SAS/SATA expander on the rear panel).
®
MSAS_HD1
2-26
BP8LX12G-35-R20E
MSAS_HD2
Chapter 2: Hardware Information
RS520-E8-RS12-EV2
connect to the 8-pin
power connector
connect to mini-SAS HD connectors 1 and 2 on the backplane. With
two mini-SAS HD cables connected, a total number of 12 SAS/SATA
HDDs can be supported (SAS/SATA expander on the rear panel).
MSAS_HD1
MSAS_HD2
®
BP12EX12G-35-R2DF
MSAS_HD3
Reserved for future expansions
®
BP12EX12G-35-R2DF
BPSMB1: connect to the SMB(6-1 pin FPSMB)
connector on the auxiliary panel
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-27
2.8
Removable/optional components
This section explains how to install optional components into the system and covers the
following components:
1.
System fans
2.
Slim type optical drive (optional)
3.
Redundant power supply module (optional)
Ensure that the system is turned off before removing any components.
2.8.1
System fans
To uninstall the system fans:
1.
Hold two levers on both sides of the fan, then lift the fan to remove.
2.
Repeat steps 1 to uninstall the other system fans.
To reinstall the system fans
1.
2-28
Insert the fan into the fan cage. The
airflow directional arrow on the fan side
should point towards the CPU heatsink.
Chapter 2: Hardware Information
2.8.2 Slim optical drive (optional, for RS520-E8-RS8 V2
only)
To install the optional optical drive:
1.
Remove 2 screws that secure the slim
optical drive cover to the chassis.
2.
Secure two screws on each side of
the optical drive to secure it into the
expansion bracket.
3.
Place the slim optical drive into the
expansion bay.
4.
Ensure the expansion tray is completely
inserted into the bay. (The drive tray
is correctly placed when its front edge
aligns with the bay edge.)
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-29
To remove or uninstall the slim type optical disk drive:
2-30
1.
Locate the optical drive eject latch at
the back of the optical drive bay.
2.
Press the optical drive eject latch to
the right then push the slim type optical
drive towards the front panel.
Chapter 2: Hardware Information
2.8.3
Redundant power supply module
To replace a failed redundant power supply module:
1.
Press the secure tab to the left using your thumb, and hold the power supply module
lever using other fingers.
A
2.
Pull the power supply module out of the system chassis ( B ).
B
3.
Insert the replacement power supply module into the chassis.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
2-31
2-32
Chapter 2: Hardware Information
Chapter 3: Installation Options
Installation Options
This chapter describes how to install the optional components
and devices into the barebone server.
3
3.1
Tool-less Friction Rail Kit
The tool-less design of the rail kit allows you to easily install the rack rails into the server rack
without the need for additional tools. The kit also comes with a metal stopping bracket that
can be installed to provide additional support and stability to the server.
The tool-less rail kit package includes:
Set of screws
Fixing latches
Rail components (screws included)
Latch screws Rail Washers
Rail screws
Tool-less rack rail
Installing the tool-less rack rail
To install the tool-less rack rails into the rack:
1. Secure the two fixing latches to the two sides of the server using the set of latch screws.
The locations of the screw holes vary with different server models. Refer to your server user
manual for details.
3-2
Chapter 3: Installation Options
2. Select a desired space and place the appropriate rack rail (left and right) on opposite positions on the rack.
A 1U space is consists of three square mounting holes with two thin lips on the top and the
bottom.
1U
3.
Secure the rail components to the rail using the bundled screws.
4
Press the spring lock (
) then insert the studs into the selected square mounting
holes on the rack post.
5. Press the spring lock on the other end of rail then insert the stud into the mounting hole
on the rack post. Extend the rack rail, if necessary.
6. (Optional) Use the rail screw and rail washer (
) that comes with the kit to secure
the rack rail to the rack post.
7. Perform steps 3 to 5 for the other rack rail.
Ensure that the installed rack rails (left and right) are aligned, secured, and stable in place.
8. Lift the server chassis and insert into the rack rail.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
3-3
•
Ensure that the rack rail cabinet and the rack posts are stable and standing firmly on a
level surface.
•
We strongly recommend that at least two able-bodied persons perform the steps
described in this guide.
•
We recommend the use an appropriate lifting tool or device, if necessary.
RS520-E8-RS8 V2 Front View
4
3
2
1
RS520-E8-RS12-EV2 Front View
3-4
Chapter 3: Installation Options
Chapter 4: Motherboard Information
Motherboard Information
This chapter includes the motherboard layout and brief
descriptions of the jumpers and internal connectors.
4
4.1
Motherboard layout
Layout contents
Jumpers
4-2
Page
1.
Clear RTC RAM (3-pin CLRTC1)
4-4
2.
VGA controller setting (3-pin VGA_SW1)
4-5
3.
LAN controller setting (3-pin LAN_SW1, LAN_SW2)
4-5
4.
ME firmware force recovery setting (3-pin ME_RCVR1)
4-6
5.
DDR4 thermal event setting (3-pin DIMMTRIP1)
4-6
6.
RAID configuration utility selection (3-pin RAID_SEL1)
4-7
7.
BMC Setting (3-pin BMC_EN1)
4-7
Chapter 4: Motherboard Information
Internal connectors
Page
1.
Serial ATA 6.0 / 3.0 Gbps connector (7-pin SATA6 [Light Blue])
4-8
2.
Power Supply SMBus connector (5-pin PSUSMB1)
4-8
3.
USB 2.0 connector (10-1 pin USB56; USB7)
4-9
4.
USB 3.0 connector (20-1 pin USB3_34)
4-9
5.
CPU, front, and rear fan connectors (4-pin CPU_FAN1, CPU_
FAN2, FRNT_FAN1, FRNT_FAN2, FRNT_FAN3, FRNT_FAN4,
FRNT_FAN5, REAR_FAN1, REAR_FAN2)
4-10
6.
LAN Activity LED connector (5-1 pin LAN34_LED1)
4-10
7.
Serial port connector (10-1 pin COM1)
4-11
8.
Trusted Platform Module connector (20-1 pin TPM1)
4-11
9.
ATX power connectors (24-pin EATXPWR1, 8-pin EATX12V1,
8-pin EATX12V2)
4-12
10.
System panel connector (20-1 pin PANEL1)
4-13
11.
Auxiliary panel connector (20-2 pin AUX_PANEL1)
4-14
12.
VGA connector (10-1 pin VGA_HDR1)
4-15
13.
Hard disk activity LED connector (4-pin HDLED1)
4-15
14.
Chassis Intrusion (2-pin INTRUSION1)
4-16
15.
ISATA & ISSATA connectors (ISATA; ISSATA)
4-16
16.
M.2 (NGFF) connector (NGFF1)
4-17
17.
Mezzanine PCI card connector (MEZZ1)
4-17
Onboard LEDs
Page
1.
Standby Power LED (SBPWR1)
4-18
2.
Baseboard Management Controller LED (BMCLED1)
4-18
3.
CPU Warning LED (ERRCPU1, ERRCPU2)
4-19
4.
Location LED (LOCLED1)
4-19
5.
Memory error LED (MEMERRA1, MEMERRA2, MEMERRB1,
MEMERRB2, MEMERRC1, MEMERRC2, MEMERRD1,
MEMERRD2, MEMERRE1, MEMERRE2, EMERRF1,
MEMERRF2, MEMERRG1, MEMERRG2, MEMERRH1,
MEMERRH2)
4-20
6.
CATT LED (CATTERR_LED1)
4-20
7.
Message LED (MESLED1)
4-21
8.
OCPLAN Activity LED connector (4-pin OCP_LED1)
4-21
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-3
4.2Jumpers
1.
Clear RTC RAM (3-pin CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can
clear the CMOS memory of date, time, and system setup parameters by erasing the
CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS
which includes system setup information such as system passwords.
To erase the RTC RAM:
1.
Turn OFF the computer and unplug the power cord.
2.
Move the jumper cap from the default pins 1–2 to pins 2–3. Keep the cap on pins
2–3 for about 5 to 10 seconds, then move the cap back to pins 1–2.
3.
Plug the power cord and turn ON the computer.
4.
Hold down the <Del> key during the boot process and enter BIOS setup to reenter data.
DO NOT remove the cap on CLRTC jumper default position except when clearing the RTC
RAM. Removing the cap will cause system boot failure!
If the steps above do not help, remove the onboard battery and move the jumper again to
clear the CMOS RTC RAM data. After the CMOS clearance, reinstall the battery.
4-4
Chapter 4: Motherboard Information
2.
VGA controller setting (3-pin VGA_SW1)
This jumper allows you to enable or disable the onboard VGA controller. Set to pins
1–2 to activate the VGA feature.
3.
LAN controller setting (3-pin LAN_SW1, LAN_SW2)
These jumpers allow you to enable or disable the onboard LAN_SW1 or LAN_SW2.
Set to pins 1–2 to activate the Gigabit LAN feature.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-5
4-6
4.
ME firmware force recovery setting (3-pin ME_RCVR1)
This jumper allows you to force Intel® Management Engine (ME) boot from recovery
mode when ME becomes corrupted.
5.
DDR4 thermal event setting (3-pin DIMMTRIP1)
This jumper allows you to enable or disable DDR4 DIMM thermal sensing event pin.
Chapter 4: Motherboard Information
6.
RAID configuration utility selection (3-pin RAID_SEL1)
This jumper allows you to select the RAID configuration utility to use when you create
disk arrays. Place the jumper caps over pins 1–2 to use the third party software LSI
MegaRAID software RAID Configuration Utility; otherwise, place the jumper caps to
pins 2–3 to use the Intel® Rapid Storage Technology enterprise SATA Option ROM
Utility.
7.
BMC Setting (3-pin BMC_EN1)
This jumper allows you to enable or disable the Baseboard Management Controller
(ASMB8).
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-7
4.3
1.
Internal connectors
Serial ATA 6.0 / 3.0 Gbps connector (7-pin SATA6 [Light Blue])
Supported by the Intel® 610 series Chipset, this connector is for the Serial ATA signal
cables for Serial ATA hard disk drives that allows up to 6 Gbps of data transfer rate.
The actual data transfer rate depends on the speed of Serial ATA hard disks installed.
2.
Power Supply SMBus connector (5-pin PSUSMB1)
This connector allows you to connect SMBus (System Management Bus) to the PSU
(power supply unit) to read PSU information. Devices communicate with an SMBus
host and/or other SMBus devices using the SMBus interface.
This connector functions only when you install the ASUS ASMB8.
4-8
Chapter 4: Motherboard Information
3.
USB 2.0 connector (10-1 pin USB56; USB7)
These connectors are for USB 2.0 ports. Connect the USB module cables to
connectors USB56. These USB connectors comply with USB 2.0 specification that
supports up to 480 Mb/s connection speed.
4.
USB 3.0 connector (20-1 pin USB3_34)
This connector allows you to connect a USB 3.0 module for additional USB 3.0 front
or rear panel ports. With an installed USB 3.0 module, you can enjoy all the benefits of
USB 3.0 including faster data transfer speeds of up to 5Gbps, faster charging time for
USB-chargeable devices, optimized power efficiency, and backward compatibility with
USB 2.0.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-9
5.
CPU, front, and rear fan connectors (4-pin CPU_FAN1, CPU_FAN2, FRNT_FAN1, FRNT_FAN2, FRNT_FAN3, FRNT_FAN4, FRNT_FAN5, REAR_FAN1, REAR_FAN2)
The fan connectors support cooling fans. Connect the fan cables to the fan connectors
on the motherboard, ensuring that the black wire of each cable matches the ground pin
of the connector.
6.
•
DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow
inside the system may damage the motherboard components.
•
These are not jumpers! DO NOT place jumper caps on the fan connectors!
•
All fans feature the ASUS Smart Fan technology.
LAN Activity LED connector (5-1 pin LAN34_LED1)
These leads are for 10G LAN activity LEDs on the front panel. Connect the LAN LED
cable to the backplane for LAN activity indication.
4-10
Chapter 4: Motherboard Information
7.
Serial port connector (10-1 pin COM1)
This connector is for the serial COM port. Connect the serial port module cable to one
of these connectors, then install the module to a slot opening at the back of the system
chassis.
8.
Trusted Platform Module connector (20-1 pin TPM1)
This connector supports a Trusted Platform Module (TPM) system, which can securely
store keys, digital certificates, passwords, and data. A TPM system also helps enhance
network security, protects digital identities, and ensures platform integrity.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-11
9.
ATX power connectors (24-pin EATXPWR1, 8-pin EATX12V1, 8-pin EATX12V2)
These connectors are for the ATX power supply plugs. The power supply plugs are
designed to fit these connectors in only one orientation. Find the proper orientation and
push down firmly until the connectors completely fit.
4-12
•
DO NOT forget to connect the 24-pin and the 8-pin power plugs; otherwise, the system
will not boot up.
•
Use of a power supply unit (PSU) with a higher power output is recommended when
configuring a system with more power-consuming devices. The system may become
unstable or may not boot up if the power is inadequate.
•
This motherboard supports ATX2.0 PSU or later version.
•
Ensure that your PSU can provide at least the minimum power required by your
system.
Chapter 4: Motherboard Information
10. System panel connector (20-1 pin PANEL1)
This connector supports several chassis-mounted functions.
1. System power LED (3-pin PLED)
This 3-pin connector is for the system power LED. Connect the chassis power
LED cable to this connector. The system power LED lights up when you turn on
the system power, and blinks when the system is in sleep mode.
2. Message LED (2-pin MLED)
This 2-pin connector is for the message LED cable that connects to the front
message LED. The message LED is controlled by Hardware monitor to indicate
an abnormal event occurrence.
3. System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The
speaker allows you to hear system beeps and warnings.
4. Hard disk drive activity LED (2-pin +HDLED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED
cable to this connector. The HD LED lights up or flashes when data is read from
or written to the HDD.
5. Power button/soft-off button (2-pin PWRSW)
This connector is for the system power button. Pressing the power button turns
the system on or puts the system in sleep or soft-off mode depending on the BIOS
settings. Pressing the power switch for more than four seconds while the system
is ON turns the system OFF.
6. Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot
without turning off the system power.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-13
11. Auxiliary panel connector (20-2 pin AUX_PANEL1)
This connector is for additional front panel features including front panel SMB, locator
LED and switch, chassis intrusion, and LAN LEDs.
1. Front panel SMB (10-2 pin FPSMB)
These connectors are for the front panel SMBus cable.
2. LAN activity LED (2-pin LAN1_LINKACTLED, LAN2_LINKACTLED)
These connectors are for Gigabit LAN activity LEDs on the front panel.
3. Locator LED (2-pin LOCATORLED1, LOCATORLED2)
These connectors are for the locator LED1 and LED2 on the front panel. Connect
the Locator LED cables to these 2-pin connector. The LEDs will light up when the
Locator button is pressed.
4. Locator Button/Switch (2-pin LOCATORBTN#)
4-14
These connectors are for the locator button on the front panel. This button queries
the state of the system locator.
Chapter 4: Motherboard Information
12. VGA connector (10-1 pin VGA_HDR1)
This connector supports the VGA High Dynamic-Range interface.
13. Hard disk activity LED connector (4-pin HDLED1)
This LED connector is for the storage add-on card cable connected to the SATA or
SAS add-on card. The read or write activities of any device connected to the SATA or
SAS add-on card causes the front panel LED to light up.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-15
14. Chassis Intrusion (2-pin INTRUSION1)
These leads are for the intrusion detection feature for chassis with intrusion sensor or
microswitch. When you remove any chassis component, the sensor triggers and sends
a high level signal to these leads to record a chassis intrusion event. The default setting
is short CASEOPEN and GND pin by jumper cap to disable the function.
15. ISATA & ISSATA connectors (ISATA; ISSATA)
The ISATA connector (AHCI) supports 4 SATA 6Gb/s ports and Intel RAID/LSI
MegaRAID.
The ISSATA connector (AHCI) supports 4 SATA 6Gb/s ports and Intel RAID.
4-16
Chapter 4: Motherboard Information
16. M.2 (NGFF) connector (NGFF1)
This connector allows you to install an M.2 device.
This connector supports type 2242 devices on both PCI-E and SATA interface.
The M.2 (NGFF) device is purchased separately
17. Mezzanine PCI card connector (MEZZ1)
The MEZZ1 connector supports Open Compute Project (OCP) cards.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-17
4.4
Onboard LEDs
1.
Standby Power LED (SBPWR1)
The motherboard comes with a standby power LED. The green LED lights up to
indicate that the standby mode of the system is ON, the system is in sleep mode,
or the system is in soft-off mode. This is a reminder that you should shut down the
system and unplug the power cable before removing or plugging in any motherboard
component. The illustration below shows the location of the onboard LED.
2.
Baseboard Management Controller LED (BMCLED1)
The green heartbeat LED blinks per second to indicate that the ASMB8 is working
normally.
The heartbeat LED functions only when you install the ASUS ASMB8.
4-18
Chapter 4: Motherboard Information
3.
CPU Warning LED (ERRCPU1, ERRCPU2)
The CPU warning LEDs light up to indicate failure on either CPU1, CPU2, or both.
4.
Location LED (LOCLED1)
This onboard LED lights up when the Location button on the server is pressed or when
triggered by a system management software. The Location LED helps visually locate
and quickly identify the server in error on a server rack.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-19
5. Memory error LED (MEMERRA1, MEMERRA2, MEMERRB1, MEMERRB2, MEMERRC1, MEMERRC2, MEMERRD1, MEMERRD2, MEMERRE1, MEMERRE2, EMERRF1, MEMERRF2, MEMERRG1, MEMERRG2, MEMERRH1, MEMERRH2)
The DIMM warning LEDs light up to indicate failure on the corresponding DIMMs.
The warning LEDs only functions when you enable the ASUS ASMB8.
6.
CATT LED (CATTERR_LED1)
The CATT LED indicates that the system has experienced a fatal or catastrophic error
and cannot continue to operate.
4-20
Chapter 4: Motherboard Information
7.
Message LED (MESLED1)
This onboard LED lights up to red when there is temperature warning or a BMC event
log is generated.
8.
OCPLAN Activity LED connector (4-pin OCP_LED1)
OCPLAN LED connector supports ASUS MCB-10G-2S OCP card Active LED.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
4-21
4-22
Chapter 4: Motherboard Information
Chapter 5: BIOS Setup
BIOS Setup
This chapter tells how to change the system settings through
the BIOS Setup menus. Detailed descriptions of the BIOS
parameters are also provided.
5
5.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard Basic Input/Output
System (BIOS) setup:
1.
ASUS CrashFree BIOS 3
To recover the BIOS using a bootable USB flash disk drive when the BIOS file fails or
gets corrupted.
2.
ASUS EzFlash
Updates the BIOS using a USB flash disk.
3.
BUPDATER
Updates the BIOS in DOS mode using a bootable USB flash disk drive.
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable USB flash disk drive in
case you need to restore the BIOS in the future. Copy the original motherboard BIOS using
the BUPDATER utility.
5.1.1
ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file
when it fails or gets corrupted during the updating process. You can update a corrupted BIOS
file using a USB flash drive that contains the updated BIOS file.
Prepare a USB flash drive containing the updated motherboard BIOS before using this
utility.
Recovering the BIOS from a USB flash drive
To recover the BIOS from a USB flash drive:
1.
Insert the USB flash drive with the original or updated BIOS file to one USB port on the
system.
2.
The utility will automatically recover the BIOS. It resets the system when the BIOS
recovery finished.
DO NOT shut down or reset the system while recovering the BIOS! Doing so would cause
system boot failure!
The recovered BIOS may not be the latest BIOS version for this motherboard. Visit the
ASUS website at www.asus.com to download the latest BIOS file.
5-2
Chapter 5: BIOS Setup
5.1.2
ASUS EZ Flash 2 Utility
The ASUS EZ Flash 2 Utility feature allows you to update the BIOS without having to use a
DOS‑based utility.
Before you start using this utility, download the latest BIOS from the ASUS website at www.
asus.com.
To update the BIOS using EZ Flash 2 Utility
1.
Insert the USB flash disk that contains the latest BIOS file into the USB port.
2.
Enter the BIOS setup program. Go to the Tool menu then select ASUS EZ Flash 2
Utility. Press <Enter>.
ASUS Tek. EzFlash Utility
Current Platform
Platform : Z10PR-D16
Version : 0020
Build Date :04/25/2014
FS0
New Platform
Platform : Z10PR-D16
Version : 0022
Build Date :05/05/2014
System Volume Information
Z10PR-D16 BIOS
Windows
<DIR>
<DIR>
<DIR>
[Up/Down/Left/Right]:Switch [Enter]:Choose [q]:Exit
3.
Press <Tab> to switch to the Drive field.
4.
Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS,
then press <Enter>.
5.
Press <Tab> to switch to the Folder Info field.
6.
Press the Up/Down arrow keys to find the BIOS file, and then press <Enter> to perform
the BIOS update process. Reboot the system when the update process is done.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-3
•
This function can support devices such as a USB flash disk with FAT 32/16 format and
single partition only.
•
DO NOT shut down or reset the system while updating the BIOS to prevent system
boot failure!
Ensure to load the BIOS default settings to ensure system compatibility and stability. Press
<F5> and select Yes to load the BIOS default settings.
5.1.3
BUPDATER utility
The succeeding BIOS screens are for reference only. The actual BIOS screen displays
may not be the same as shown.
The BUPDATER utility allows you to update the BIOS file in the DOS environment using a
bootable USB flash disk drive with the updated BIOS file.
Updating the BIOS file
To update the BIOS file using the BUPDATER utility:
1.
Visit the ASUS website at www.asus.com and download the latest BIOS file for the
motherboard. Save the BIOS file to a bootable USB flash disk drive.
2.
Copy the BUPDATER utility (BUPDATER.exe) from the ASUS support website at
support.asus.com to the bootable USB flash disk drive you created earlier.
3.
Boot the system in DOS mode, then at the prompt, type:
BUPDATER /i[filename].CAP
where [filename] is the latest or the original BIOS file on the bootable USB flash disk
drive, then press <Enter>.
A:\>BUPDATER /i[file name].CAP
5-4
Chapter 5: BIOS Setup
4.
The utility verifies the file, then starts updating the BIOS file.
ASUS Tek. EzFlash Utility
Current Platform
Platform : Z10PR-D16
Version : 0401
Build Date :09/05/2013
New Platform
Platform : Z10PR-D16
Version : 0606
Build Date :03/27/2014
Start programming the Flash. DO NOT SHUTDOWN THE SYSTEM!!!
Write ...
25%
DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!
5.
The utility returns to the DOS prompt after the BIOS update process is completed.
Reboot the system from the hard disk drive.
The BIOS update is finished! Please restart your system.
C:\>
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-5
5.2
BIOS setup program
This motherboard supports a programmable firmware chip that you can update using the
provided utility described in section 5.1 Managing and updating your BIOS.
Use the BIOS Setup program when you are installing a motherboard, reconfiguring your
system, or prompted to “Run Setup.” This section explains how to configure your system
using this utility.
Even if you are not prompted to use the Setup program, you can change the configuration of
your computer in the future. For example, you can enable the security password feature or
change the power management settings. This requires you to reconfigure your system using
the BIOS Setup program so that the computer can recognize these changes and record them
in the CMOS RAM of the firmware chip.
The firmware chip on the motherboard stores the Setup utility. When you start up the
computer, the system provides you with the opportunity to run this program. Press <Del>
during the Power-On Self-Test (POST) to enter the Setup utility; otherwise, POST continues
with its test routines.
If you wish to enter Setup after POST, restart the system by pressing <Ctrl+Alt+Delete>, or by
pressing the reset button on the system chassis. You can also restart by turning the system
off and then back on. Do this last option only if the first two failed.
The Setup program is designed to make it as easy to use as possible. Being a menu-driven
program, it lets you scroll through the various sub-menus and make your selections from the
available options using the navigation keys.
5-6
•
The default BIOS settings for this motherboard apply for most conditions to ensure
optimum performance. If the system becomes unstable after changing any BIOS
settings, load the default settings to ensure system compatibility and stability. Press
<F5> and select Yes to load the BIOS default settings.
•
The BIOS setup screens shown in this section are for reference purposes only, and
may not exactly match what you see on your screen.
•
Visit the ASUS website (www.asus.com) to download the latest BIOS file for this
motherboard.
Chapter 5: BIOS Setup
5.2.1
BIOS menu screen
Menu items
Menu bar
Configuration fields
General help
Navigation keys
5.2.2
Menu bar
The menu bar on top of the screen has the following main items:
Main For changing the basic system configuration
Advanced
For changing the advanced system settings
IntelRCSetup
For changing the Intel RC settings
Server Mgmt
For changing the Server Mgmt settings
Event Logs
For changing the event log settings
Monitor or displaying the system temperature, power status, and changing
F
the fan settings
Security For changing the security settings
Boot For changing the system boot configuration
Tool For configuring options for special functions
Exit
For selecting the exit options
To select an item on the menu bar, press the right or left arrow key on the keyboard until the
desired item is highlighted.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-7
5.2.3
Menu items
The highlighted item on the menu bar displays the specific items for that menu. For example,
selecting Main shows the Main menu items.
The other items (Event Logs, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have
their respective menu items.
5.2.4
Submenu items
A solid triangle before each item on any menu screen means that the item has a submenu.
To display the submenu, select the item then press <Enter>.
5.2.5
Navigation keys
At the bottom right corner of a menu screen are the navigation keys for the BIOS setup
program. Use the navigation keys to select items in the menu and change the settings.
5.2.6
General help
At the top right corner of the menu screen is a brief description of the selected item.
5.2.7
Configuration fields
These fields show the values for the menu items. If an item is user-configurable, you can
change the value of the field opposite the item. You cannot select an item that is not userconfigurable.
A configurable field is enclosed in brackets, and is highlighted when selected. To change the
value of a field, select it and press <Enter> to display a list of options.
5.2.8
Pop-up window
Select a menu item and press <Enter> to display a pop-up window with the configuration
options for that item.
5.2.9
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not fit
on the screen. Press the Up/Down arrow keys or <Page Up> /<Page Down> keys to display
the other items on the screen.
5-8
Chapter 5: BIOS Setup
5.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears. The Main menu
provides you an overview of the basic system information, and allows you to set the system
date, time, language, and security settings.
5.3.1
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
5.3.2
System Time [xx:xx:xx]
Allows you to set the system time.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-9
5.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system
devices.
Take caution when changing the settings of the Advanced menu items. Incorrect field
values can cause the system to malfunction.
5-10
Chapter 5: BIOS Setup
5.4.1
ACPI Settings
Enable ACPI Auto Configuration [Disabled]
Allows you to enable or disable the BIOS ACPI Auto Configuration.
Configuration options: [Disabled] [Enabled]
Enable Hibernation [Enabled]
Allows you to enable or disable the ability of the system to hibernate (OS/Sleep State).
Configuration options: [Disabled] [Enabled]
This option may be not effective with some OS.
5.4.2
Smart Settings
SMART Self Test [Disabled]
Allows you to run SMART Self Test on all HDDs during POST.
Configuration options: [Disabled] [Enabled]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-11
5.4.3
NCT6779D Super IO Configuration
Serial Port 1 / Serial Port 2 Configuration
Allows you to set the parameters of Serial Port 1/ Serial Port 2.
Serial Port [Enabled]
Allows you to enable or disable Serial Port.
Configuration options: [Disabled] [Enabled]
Change Settings [Auto]
Allows you to choose the setting for Super IO device.
Configuration options: [Auto] [IO=3F8h; IRQ=4;] [IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;]
[IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;] [IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;]
[IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;]
5-12
Chapter 5: BIOS Setup
5.4.4
Intel LAN I210 Configuration
Intel I210 Lan1 Enable/ Intel I210 Lan2 Enable [Enabled]
Allows you to enable or disable the Intel LAN.
Configuration options: [Disabled] [Enabled]
Intel LAN ROM Type [PXE]
Allows you to select the Intel LAN ROM type.
Configuration options: [Disabled] [PXE] [iSCSI]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-13
5.4.5
Serial Port Console Redirection
COM1/COM2
Console Redirection [Disabled]
Allows you to enable or disable the console redirection feature.
Configuration options: [Disabled] [Enabled]
The following item appears only when you set Console Redirection to [Enabled].
Console Redirection Settings
This item becomes configurable only when you enable the Console Redirection item. The
settings specify how the host computer and the remote computer (which the user is using)
will exchange data. Both computers should have the same or compatible settings.
Terminal Type [VT-UTF8]
Allows you to set the terminal type.
[VT100]
ASCII char set.
[VT100+]
Extends VT100 to support color, function keys, et.
[VT-UTF8]
Uses UTF8 encoding to map Unicode chars onto 1 or more bytes
[ANSI]
Extended ASCII char set
Bits per second [57600]
Selects serial port transmission speed. The speed must be matched on the other side.
Long or noisy lines may require lower speeds.
Configuration options: [9600] [19200] [38400] [57600] [115200]
Data Bits [8]
Configuration options: [7] [8]
Parity [None]
A parity bit can be sent with the data bits to detect some transmission errors. [Mark]
and [Space] parity do not allow for error detection.
[None]
None
[Even]
parity bit is 0 if the num of 1’s in the data bits is even
[Odd]
parity bit is 0 if num of 1’s in the data bits is odd
[Mark]
parity bit is always 1
[Space]
parity bit is always 0
5-14
Chapter 5: BIOS Setup
Stop Bits [1]
Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning.)
The standard setting is 1 stop bit. Communication with slow devices may require more
than 1 stop bit. Configuration options: [1] [2]
Flow Control [Hardware RTS/CTS]
Flow control can prevent data loss from buffer overflow. When sending data, if the
receiving buffers are full, a “stop” signal can be sent to stop the data flow. Once the
buffers are empty, a “start” signal can be sent to re-start the flow. Hardware flow control
uses two wires to send start/stop signals.
Configuration options: [None] [Hardware RTS/CTS]
VT -UTF8 Combo Key Support [Enabled]
This allows you to enable the VT -UTF8 Combination Key Support for ANSI/VT100
terminals. Configuration options: [Disabled] [Enabled]
Recorder Mode [Disabled]
With this mode enabled only text will be sent. This is to capture Terminal data.
Configuration options: [Disabled] [Enabled]
Legacy OS Redirection Resolution [80x24]
This allows you to set the number of rows and columns supported on the Legacy OS.
Configuration options: [80x24] [80x25]
Putty Keypad [VT100]
This allows you to select the FunctionKey and Keypad on Putty. Configuration options:
[VT100] [LINUX] [XTERMR6] [SCO] [ESCN] [VT400]
Redirection After BIOS POST [Always Enable]
This setting allows you to specify if Bootloader is selected than Legacy console
redirection. Configuration options: [Always Enable] [Bootloader]
Serial Port for Out-of-Band Management/ Windows Emergency Management
Services (EMS)
Console Redirection [Disabled]
Allows you to enable or disable the console redirection feature.
Configuration options: [Disabled] [Enabled]
The following item appears only when you set Console Redirection to [Enabled].
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-15
Console Redirection Settings
Out-of-Band Mgmt Port [COM1]
Microsoft Windows Emergency Management Services (EMS) allow for remote
management of a Windows Server OS through a serial port.
Configuration options: [COM1] [COM2]
Terminal Type [VT-UTF8]
Microsoft Windows Emergency Management Services (EMS) allow for remote
management of a Windows Server OS through a serial port.
Configuration options: [VT100] [VT100+] [VT-UTF8] [ANSI]
Bits per second [115200]
Microsoft Windows Emergency Management Services (EMS) allow for remote
management of a Windows Server OS through a serial port.
Configuration options: [9600] [19200] [57600] [115200]
Flow Control [None]
Microsoft Windows Emergency Management Services (EMS) allow for remote
management of a Windows Server OS through a serial port.
Configuration options: [None] [Hardware RTS/CTS] [Software Xon/Xoff]
5-16
Chapter 5: BIOS Setup
5.4.6APM
Restore AC Power Loss [Last State]
When set to [Power Off], the system goes into off state after an AC power loss. When set
to [Power On], the system will reboot after an AC power loss. When set to [Last State], the
system goes into either off or on state, whatever the system state was before the AC power
loss.
Configuration options: [Power Off] [Power On] [Last State]
Power On By PCIE [Disabled]
[Disabled]
Disables the PCIE devices to generate a wake event.
[Enabled]
Enables the PCIE devices to generate a wake event.
Power On By Ring [Disabled]
[Disabled]
Disables the PCIE devices to generate a wake event.
[Enabled]
Enables the PCIE devices to generate a wake event.
Power On By RTC [Disabled]
[Disabled]
Disables RTC to generate a wake event.
[Enabled]
When set to [Enabled], the items RTC Alarm Date (Days) and Hour/
Minute/Second will become user-configurable with set values.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-17
5.4.7
PCI Subsystem Settings
Load RT32 Image [Enabled]
Allows you to enable or disable RT32 Image Loading.
Configuration options: [Disabled] [Enabled]
Above 4G Decoding [Disabled]
Allows you to enable or disable 64-bit capable devices to be decoded in above 4G address
space. It only works if the system supports 64-bit PCI decoding.
Configuration options: [Disabled] [Enabled]
SR-IOV Support [Disabled]
This option enables or disables Single Root IO Virtualization Support if the system has SRIOV capable PCIe devices.
Configuration options: [Disabled] [Enabled]
5-18
Chapter 5: BIOS Setup
5.4.8
Network Stack Configuration
Network stack [Disabled]
Enables or disables the network stack feature. Configuration options: [Disable] [Enable]
The following item appears only when Network stack is set to [Enabled].
Ipv4 PXE Support [Enabled]
Enables or disables the Ipv4 PXE Boot Support. If disabled, Ipv4 PXE boot option will
not be created. Configuration options: [Disabled] [Enabled].
Ipv6 PXE Support [Enabled]
Enables or disables the Ipv6 PXE Boot Support. If disabled, Ipv6 PXE boot option will
not be created. Configuration options: [Disabled] [Enabled].
PXE boot wait time [0]
Wait time to press ESC key to abort the PXE boot.
Media detect time [0]
Wait time (in seconds) to detect media.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-19
5.4.9
CSM Configuration
CSM Support [Enabled]
This option allows you to enable or disable CSM Support.
Configuration options: [Disabled] [Enabled]
GateA20 Active [Upon Request]
This allows you to set the GA20 option.
Configuration options: [Upon Request] [Always]
Option ROM Messages [Force BIOS]
This allows you to set the display mode for option ROM.
Configuration options: [Force BIOS] [Keep Current]
Boot Option filter [Legacy only]
This option allows you to control the Legacy/UEFI ROMs priority.
Configuration options: [UEFI and Legacy] [Legacy only] [UEFI only]
Network / Storage / Video [Legacy]
This option allows you to control the execution of UEFI and Legacy PXE/ Storage/ Video
OpROM.
Configuration options: [UEFI ] [Legacy]
Other PCI device [Legacy]
This item determines the OpROM execution policy for devices other than Network, Storage,
or Video.
Configuration options: [UEFI ] [Legacy]
5-20
Chapter 5: BIOS Setup
5.4.10
Trusted Computing
Configuration
Security Device Support [Disabled]
Allows you to enable or disable the BIOS support for security device.
Configuration options: [Disabled] [Enabled]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-21
5.4.11
USB Configuration
Legacy USB Support [Enabled]
Allows you to enable or disable Legacy USB device support.
Configuration options: [Enabled] [Disabled] [Auto]
XHCI Hand-off [Enabled]
This is a workaround for 0Ses without XHCI hand-off support. The XHCI ownership change
should be claimed by XHCI driver.
Configuration options: [Disabled] [Enabled]
EHCI Hand-off [Disabled]
This is a workaround for 0Ses without EHCI hand-off support. The EHCI ownership change
should be claimed by EHCI driver.
Configuration options: [Disabled] [Enabled]
USB Mass Storage Driver Support [Enabled]
Allows you to enable or disable the USB Mass Storage drvier support.
Configuration options: [Disabled] [Enabled]
Port 60/64 Emulation [Enabled]
This allows you to enable the I/O port 60h/64h emulation support. This should be enabled for
the complete USB keyboard legacy support for non-USB aware OSes.
Configuration options: [Disabled] [Enabled]
5-22
Chapter 5: BIOS Setup
USB hardware delays and time-outs
USB transfer time-out [20 sec]
The time-out value for control, bulk, and interrupt transfer.
Configuration options: [1 sec] [5 sec] [10 sec] [20 sec]
Device reset time-out [20 sec]
USB mass storage device start unit command time-out.
Configuration options: [10 sec] [20 sec] [30 sec] [40 sec]
Device power-up delay [Auto]
This is the maximum time the device will take before it properly reports itself to the host
controller.
Configuration options: [Auto] [Manual]
5.4.12
iSCSI Configuration
Allows you to configure the iSCSi parameters.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-23
5.5
5-24
IntelRCSetup menu
Chapter 5: BIOS Setup
5.5.1
Processor Configuration
Per Socket Configuration
Allows you to set the number of cores to enable. 0 means all cores. Total of 14 cores
available.
Hyper Threading [Enabled]
Allows you to enable or disable the Intel® Hyper-Threading Technology function. When
disabled, only one thread per activated core is enabled.
Configuration options: [Disabled] [Enabled]
Execute Disable Bit [Enabled]
XD can prevent certain classes of malicious buffer overflow attacks when combined with
a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, Redhat
Enterprise 3 Update 3).
Configuration options: [Disabled] [Enabled]
Enable Intel TXT Support [Disabled]
Forces the XD feature log to always return 0 when disabled.
Configuration options: [Disabled] [Enabled]
VMX [Enabled]
Enables the Vanderpool Technology. Takes effect after reboot.
Configuration options: [Disabled] [Enabled]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-25
Enable SMX [Disabled]
Enables the Safer Mode Extensions
Configuration options: [Disabled] [Enabled]
Hardware Prefetcher [Enabled]
This Item allows you to turn on/off the mid level cache(L2) streamer prefetcher.
Configuration options: [Disabled] [Enabled]
Adjacent Cache Prefetch [Enabled]
This Item allows you to turn on/off prefetching of adjacent cache lines.
Configuration options: [Disabled] [Enabled]
DCU Streamer Prefetcher [Enabled]
This Item allows you to enable or disable prefetcher of next L1 data line.
Configuration options: [Disabled] [Enabled]
DCU IP Prefetcher [Enabled]
This Item allows you to enable or disable prefetch of next L1 line based upon sequential load
history.
Configuration options: [Disabled] [Enabled]
DCU Mode [32K 8Way Without ECC]
Configuration options: [32K 8Way Without ECC] [16K 4Way With ECC]
Direct Cache Access (DCA) [Auto]
This Item allows you to enable or disable Direct Cache Access.
Configuration options: [Auto] [Disabled] [Enabled]
DCA Prefetch Delay [32]
This Item allows you to set the time for the DCA Prefetch delay Help.
Configuration options: [Disabled] [8] [16] [24] [32] [40] [48] [56] [64] [72] [80] [88] [96] [104] [112]
X2APIC [Enabled]
This Item allows you to enable or disable the extended APIC support.
Configuration options: [Disabled] [Enabled]
AES-NI [Enabled]
This Item allows you to enable or disable the AES-NI support.
Configuration options: [Disabled] [Enabled]
Down Stream PECI [Disabled]
This Item allows you to enable the PCIe Down Stream PECI writer.
Configuration options: [Disabled] [Enabled]
5-26
Chapter 5: BIOS Setup
5.5.2
Advanced Power Management Configuration
Power Technology [Energy Efficient]
This item allows you to enable power management features.
Configuration options: [Disabled] [Energy Efficient] [Custom]
Config TDP [Disabled]
This item allows you to enable/disable the Config TDP.
Configuration options: [Disabled] [Enabled]
CPU Advanced PM Turning
This item allows you to set additional CPU Power Management settings.
Energy Perf BIAS
Energy Performance Tuning [Disabled]
Allows your system to select from BIOS or operating system to choose enable energy
performance bias tuning.
Configuration options: [Disabled] [Enabled]
Energy Performance Bias setting [Balanced Performance]
Allows you to set the Energy Performance Bias which overrides the OS setting.
Configuration options: [Performance] [Balanced Performance] [Balanced Power]
[Power]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-27
Power/Performance Switch [Enabled]
Allows you to switch between Power or performance.
Configuration options: [Disabled] [Enabled]
Workload Configuration [Balanced]
Optimization for the workload characterization.
Configuration options: [Balanced] [I/O sensitive]
Averaging Time Window [23]
This is used to control the effective window of the average for CO and PO time.
PO TotalTimeThreshold Low [35]
The HW switching mechanism disables the performance setting (0) when the total PO
time is less than this threshold.
PO TotalTimeThreshold High [58]
The HW switching mechanism enables the performance setting (0) when the total PO
time is greater than this threshold.
5.5.3
Common RefCode Configuration
Numa [Enabled]
This item enables or disables the Non uniform Memory Access (NUMA).
Configuration options: [Disabled] [Enabled]
5-28
Chapter 5: BIOS Setup
5.5.4
QPI Configuration
QPI General Configuration
QPI Status
This item displays information about the QPI status.
Link Speed Mode [Fast]
This item allows you to select the QPI link speed as either the fast mode or slow mode.
Configuration options: [Slow] [Fast]
Link Frequency Select [Auto]
This item allows you for selecting the QPI link frequency
Configuration options: [Auto] [6.4 GT/s] [8.0 GT/s] [9.6 GT/s]
QPI Link0p Enable [Enable]
Configuration options: [Disable] [Enable]
QPI Link1 Enable [Enable]
Configuration options: [Disable] [Enable]
QPI Status
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-29
5.5.5
Memory Configuration
Enforce POR [Auto]
Allows you to enforce POR restrictions for DDR4 frequency adn voltage programming.
Configuration options: [Auto] [Enforce POR] [Disabled] [Enforce Stretch Goals]
Memory Frequency [Auto]
Allows you to select the memory frequency setting.
Configuration options: [Auto] [1333] [1600] [1866] [2133]
Halt on mem Training Error [Enabled]
Allows you to enable or disable halt on mem Training Error.
Configuration options: [Disabled] [Enabled]
ECC Support [Auto]
Allows you to enable or disable the ECC support.
Configuration options: [Auto] [Disabled] [Enabled]
Enhanced Log Parsing [Disabled]
Allows you to enable or disable the Enhanced Log Parsing.
Configuration options: [Auto] [Disabled] [Enabled]
Data Scrambling [Auto]
Allows you to enable/disable data scrambling.
Configuration options: [Auto] [Disabled] [Enabled]
Enable ADR [Disabled]
Allows you to set the detecting and enabling of ADR.
Configuration options: [Disabled] [Enabled]
5-30
Chapter 5: BIOS Setup
C/A Parity Enable [Auto]
Allows you to enable or disable the DDR4's command address parity.
Configuration options: [Auto] [Disabled] [Enabled]
Memory Topology
Displays memory topology with DIMM population information.
Memory Thermal
Allows you to configure thermal settings.
Set Throttling Mode [Disabled]
Configuration options: [Disabled] [OLTT] [CLTT]
OLLT Peak BW [xxx]
Allows you to set the peak allowed bandwidth for OLTT. This is in percentage and valid
offset values is from 25-100.
DIMM Tem Stat [xx]
Allows you to select DIMMTEMPSTAT as temp_mid or tem_hi.
Memory Power Savings Mode [Auto]
Allows you to configure the CKE and other related Memory Power Savings features.
Configuration options: [Auto] [Disabled] [APD On] [User Defined] [Reserve] [Reserved]
Memory Power Savings Advanced Options
CK in SR [Auto]
Configuration options: [Auto] [Driven] [Tri-State] [Pulled Low] Pulled High]
MDLL Off [Auto]
Allows you to shutdown MDLL during SR when enabled.
Configuration options: [Auto] [Disabled] [Enabled]
MEMHOT Throttling Mode [Input-only]
Allows you to shutdown MDLL during SR when enabled.
Configuration options: [Disabled] [Input-only] [Output-only]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-31
Mem Electrical Throttling [Disabled]
Allows you to configure Memory Electrical throttling.
Configuration options: [Disabled] [Enabled] [Auto]
Memory Map
Channel Interleaving [Auto]
Select different channel interleaving setting.
Configuration options: [Auto] [1-way Interleave] [2-way Interleave] [3-way Interleave] [4way Interleave]
Rank Interleaving [Auto]
Select different rank interleaving setting.
Configuration options: [Auto] [1-way Interleave] [2-way Interleave] [4-way Interleave] [8way Interleave]
Memory RAS Configuration
RAS Mode [Disabled]
Allows you to enable or disable RAS Modes. Enabling Sparing and Mirroring is not
supported. In case enabled, Sparing will be selected.
Configuration options: [Disabled] [Mirror] [Lockstep Mode]
Memory Rank Sparing [Disabled]
Allows you to enable or disable Memory Rank Sparing.
Configuration options: [Disabled] [Enabled]
Correctable Error Threshold [32767]
Allows you to set the Correctable Error Threshold used for sparing, tagging, and leaky
bucket. The range is from 1 to 32767.
Patrol Scrub [Enabled]
Allows you to enable or disable Patrol Scrub.
Configuration options: [Disabled] [Enabled]
Demand Scrub [Enabled]
Allows you to enable or disable Demand Scrub.
Configuration options: [Disabled] [Enabled]
5-32
Chapter 5: BIOS Setup
5.5.6
IIO Configuration
EV DFX Features [Disabled]
Set this option to allow DFX Lock Bits to remain clear.
Configuration options: [Disabled] [Enabled]
PCIE Slot Option ROM Configuration
PCIE1/ PCIE2/ PCIE3/ PCIE4/ PCIE6 Option ROM [Disabled]
Allows you to enable or disable the PCIE1/ PCIE2/ PCIE3/ PCIE4/ PCIE6 Option ROM.
Configuration options: [Disabled] [Enabled]
Intel VT for Directed I/O (VT-d)
Intel VT for Directed I/O (VT-d) [Enabled]
Allows you to enable or disable the Intel Virtualization Technology for Directed I/O.
Configuration options: [Disabled] [Enabled]
PCI Express Global Options
TX EQ WA [Enabled]
Use special table for TX_EQ and vendor specific cards.
Configuration options: [Disabled] [Enabled]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-33
PCI-E ASPM Support (Global) [L1 Only]
This option enables or disables the ASPM support for all downstream devices.
Configuration options: [Disabled] [L1 Only]
5.5.7
PCH Configuration
PCH Devices
DeepSx Power Policies [Disabled]
Allows you to configure the DeepSx Mode configuration.
Configuration options: [Disabled] [Enabled in S5] [Enabled in S4 and S5]
PCI Express Configuration
5-34
Chapter 5: BIOS Setup
PCH DMI ASPM [Enabled]
Allows you to configure the PCH DMI ASPM.
Configuration options: [Disabled] [Enabled]
PCI Express Root Port 1 to Port 8
Allows you to configure the PCI Express Root port settings.
PCIE ASMP [Disable ASPM]
Allows you to configure the PCH DMI ASPM.
Configuration options: [Disable ASPM] [ASPM L0s] [ASPM L1] [ASPM
L0sL1] [ASPM Auto]
PCH sSATA Configuration
sSATA Controller [Enabled]
Allows you to enable or disable the sSATA Controller.
Configuration options: [Disabled] [Enabled]
Configure sSATA as [AHCI]
Allows you to identify the SATA port is connected to Solid State Drive or Hard Disk Drive.
Configuration options: [IDE] [AHCI] [RAID]
SATA Mode options
SATA LED locate [Enabled]
If enabled, LED/SGPIO hardware is attached.
Configuration options: [Disabled] [Enabled]
Support Aggressive Link Power Management [Enabled]
Allows you to enable or disable the Support Aggressive Link Power (SALP) Management.
Configuration options: [Disabled] [Enabled]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-35
SATA Port 1/ SATA Port 2/ SATA Port 3/ SATA Port 4
Port 1/ Port 2/ Port 3/ Port 4
Allows you to enable or disable the SATA port
Configuration options: [Disabled] [Enabled]
PCH SATA Configuration
SATA Controller [Enabled]
Allows you to enable or disable the SATA Controller.
Configuration options: [Disabled] [Enabled]
Configure SATA as [AHCI]
Allows you to identify the SATA port is connected to Solid State Drive or Hard Disk Drive.
Configuration options: [IDE] [AHCI] [RAID]
Support Aggressive Link Power Management [Enabled]
Allows you to enable or disable the Suport Aggressive Link Power (SALP) Management.
Configuration options: [Disabled] [Enabled]
SATA Port 1~6
Port 1/ Port 2/ Port 3/ Port 4/ Port 5/ Port 6 [Enabled]
Allows you to enable or disable the SATA port
Configuration options: [Disabled] [Enabled]
USB Configuration
xHCI Mode [Auto]
Allows you to enable or disable the mode of operation of xHCI controller.
Configuration options: [Auto] [Disabled] [Enabled]
5-36
Chapter 5: BIOS Setup
USB Ports Per-Port Disable Control [Disabled]
Allows you to control each of the USB ports 1 to 8 disabling.
Configuration options: [Disabled] [Enabled]
The following items appears only when the USB Ports Per-Port Disable Control is set to
[Enabled].
USB Port #1/ #2/ #3/ #4 [Enabled]
Configuration options: [Disabled] [Enabled]
USB 3.0 Port #1/ #2 [Enabled]
Configuration options: [Disabled] [Enabled]
Platform Thermal Configuration
PCH Thermal Device [Auto]
Allows you to enable or disable the PCH Thermal Device (D31:F6).
Configuration options: [Auto] [Disabled] [Enabled]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-37
Alert Enable Lock [Disabled]
Allows you to lock all Alert Enable settings.
Configuration options: [Disabled] [Enabled]
5.5.8
Miscellaneous Configuration
Active Video [Offboard Device]
Allows you to select the video type.
Configuration options: [Onboard Device] [Offboard Device]
5.5.9
Server ME Configuration
Displays the Server ME Technology parameters on your system.
5-38
Chapter 5: BIOS Setup
5.5.10
Runtime Error Logging Support
Runtime Error Logging
Whea Support [Disabled]
This item allows you to enable or disable the WHEA support.
Configuration options: [Disabled] [Enabled]
5.6
Server Mgmt menu
The Server Management menu displays the server management status and allows you to
change the settings.
OS Watchdog Timer [Disabled]
This item allows you to start a BIOS timer which can only be shut off by Intel Management
Software after the OS loads.
Configuration options: [Disabled] [Enabled]
The following items is configurable only when the OS Watchdog Timer is set to [Enabled].
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-39
OS Wtd Timer Timeout [10 minutes]
Allows you to configure the length for the OS Boot Watchdog Timer.
Configuration options: [5 minutes] [10 minutes] [15 minutes] [20 minutes]
OS Wtd Timer Policy [Reset]
This item allows you to configure the how the system should respond if the OS Boot Watch
Timer expires.
Configuration options: [Do Nothing] [Reset] [Power Down]
Serial Mux [Disabled]
This item allows you to enable or disable Serial Mux configuration.
Configuration options: [Disabled] [Enabled]
System Event Log
Allows you to change the SEL event log configuration.
SEL Components [Enabled]
Allows you to enable or disable all features of system Event Logging during boot.
Configuration options: [Disabled] [Enabled]
•
The following items appears only when you set SEL Components to [Enabled].
•
All values changed here do not take effect until computer is restarted.
Erase SEL [No]
Allows you to choose options for erasing SEL.
Configuration options: [No] [Yes, On next reset] [Yes, On every reset]
When SEL is Full [Do Nothing]
Allows you to choose options for reactions to a full SEL.
Configuration options: [Do Nothing] [Erase Immediately]
Log EFI Status Codes [Error code]
Disable the logging of EFI Status Codes, or log only error code, or only progress code
or, both.
Configuration options: [Disabled] [Both] [Error code] [Progress code]
5-40
Chapter 5: BIOS Setup
Bmc network configuration
The sub-items in this configuration allow you to configure the BMC network parameters.
Configuration Address source DM_LAN1/LAN1 [Previous State]
This item allows you to configure LAN channel parameters statistically or dynamically (by
BIOS or BMC). Unspecified option will not modify any BMC network parameters during
BIOS phase.
Configuration options: [Previous State] [Static] [DynamicBmcDhcp]
[DynamicBmcNonDhcp]
View System Event Log
This item allows you to view the system event log records.
IPv6 BMC Network Configuration
This item allows you to configure the parameter settings of IPv6 BMC network.
IPv6 Display Full Field [Enable]
Displays the full or brief IPv6 Field.
Configuration options: [Disable] [Enable]
IPv6 Display Full Formula [Enable]
Displays the full or brief IPv6 Formula.
Configuration options: [Disable] [Enable]
IPv6 Display Letter Case [Upper Case]
Displays the uppercase or lowercase letters of the alphabet.
Configuration options: [Lower Case] [Upper Case]
IPv6 BMC Lan Option [Enable]
This item allows you to enable or disable the IPv6 BMC LAN channel function.
Disabling this item will not modify any BMC network during BIOS phase.
Configuration options: [Disable] [Enable]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-41
IPv6 BMC LAN IP Address source [Previous State]
Select to configure LAN channel parameters statically or dynamically(by BIOS or
BMC).
Configuration options: [Previous State] [Static] [Dynamic-Obtained by BMC running
DHCP]
The following items appear only when you set IP BMC Lan IP Address Source to [Static].
IPv6 BMC LAN IP Address
Allows you to input IPv6 BMC Lan IP address.
IPv6 BMC LAN IP Prefix Length
Allows you to input IPv6 BMC Lan IP Prefix Length.
IPv6 BMC LAN Default Gateway
Allows you to input IPv6 BMC Lan Default Gateway.
IPv6 BMC LAN DNS Settings
Allows you to enter IPv6 BMC LAN DNS Settings.
IPv6 BMC LAN Link IP Address
Allows you to enter IPv6 BMC LAN Link IP address.
IPv6 BMC LAN Link IP Prefix Length
Allows you to input IPv6 BMC Lan Link IP Prefix Length.
IPv6 BMC Lan Option [Enable]
This item allows you to enavle IPv6 BMC LAN channel function. Disabling this option will not
modify any BMC network during BIOS phase.
5-42
Chapter 5: BIOS Setup
The following item appears only when you set IP BMC Lan Option to [Enable].
IPv6 BMC LAN IP Address Source [Previous State]
Select to configure LAN channel parameters statically or dynamically(by BIOS or
BMC).
Configuration options: [Previous State] [Static] [Dynamic-Obtained by BMC running
DHCP]
The following items appear only when you set IP BMC Lan IP Address Source to [Static].
IPv6 BMC LAN IP Address
Allows you to input IPv6 BMC Lan IP address.
IPv6 BMC LAN IP Prefix Length
Allows you to input IPv6 BMC Lan IP Prefix Length.
IPv6 BMC LAN Default Gateway
Allows you to input IPv6 BMC Lan Default Gateway.
IPv6 BMC LAN DNS Settings
Allows you to enter IPv6 BMC LAN DNS Settings.
IPv6 BMC LAN Link IP Address
Allows you to enter IPv6 BMC LAN Link IP address.
IPv6 BMC LAN Link IP Prefix Length
Allows you to input IPv6 BMC Lan Link IP Prefix Length.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-43
5.7
Event Logs menu
The Event Logs menu items allow you to change the event log settings and view the system
event logs.
5.7.1
Change Smbios Event Log Settings
Press <Enter> to change the Smbios Event Log configuration.
All values changed here do not take effect until computer is restarted.
Enabling/Disabling Options
Smbios Event Log [Enabled]
Change this to enable or disable all features of Smbios Event Logging during boot.
Configuration options: [Disabled] [Enabled]
Erasing Settings
Erase Event Log [No]
Choose options for erasing Smbios Event Log. Erasing is done prior to any logging activation
during reset. Configuration options: [No] [Yes, Next reset] [Yes, Every reset]
When Log is Full [Do Nothing]
Allows you to choose options for reactions to a full Smbios Event Log. Configuration options:
[Do Nothing] [Erase Immediately]
5-44
Chapter 5: BIOS Setup
Smbios Event Log Standard Settings
Log System Boot Event [Disabled]
Allows you to choose options to enable/disable logging of System boot event. Configuration
options: [Enabled] [Disabled]
MECI [1]
Mutiple Event Count Increment (MECI). The number of occurrences of a duplicate event
that must pass before the multiple-event counter associated with the log entry is updated,
specified as a numeric value in the range 1 to 255.
METW [60]
Mutiple Event Time Windows (METW). The number of minutes which must pass between
duplicate log entries which utilize a multiple-event counter. The value ranges from 0 to 99
minutes.
Custom Option
Log OEM Codes [Enabled]
Enable or disable the logging of EFI Status Codes as OEM Codes (if not already converted to
legacy). Configuration options: [Disabled] [Enabled]
Convert OEM Codes [Disabled]
Enable or disable the converting of EFI Status Codes to Standard Smbios Types (Not all may
be translated).
Configuration options: [Disabled] [Enabled]
5.7.2
View Smbios Event Log
Press <Enter> to view all smbios event logs.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-45
5.8
Monitor menu
The Monitor menu displays the system temperature/power status, and allows you to change
the fan settings.
Scroll down to view the other items
CPU1/2 Temperature [xxx°C/xxx°F]
The onboard hardware monitor automatically detects and displays the CPU temperatures.
CPU FAN1/2 Speed; FRNT FAN1–5 Speed; REAR FAN1/2 Speed
[xxxx RPM] or [N/A]
The onboard hardware monitor automatically detects and displays the speed of CPU fans,
front fans, and rear fan in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A.
+VCCIO, VCORE1/2 Voltage, +VDDQ_AB_CPU1 Voltage, +VDDQ_CD_CPU1
Voltage, +VDDQ_EF_CPU2 Voltage, +VDDQ_GH_CPU2 Voltage,
+5VSB Voltage, +5V Voltage, +12V Voltage, +3.3V Voltage, VBAT
Voltage, +3.3VSB Voltage
The onboard hardware monitor automatically detects the voltage output through the onboard
voltage regulators.
CPU FAN1&2 FRNT FAN1 mode [Generic Mode]
Allows you to configure the ASUS Smart Fan feature that smartly adjusts the fan speeds for
more efficient system operation.
Configuration options: [Generic Mode] [High Speed Mode] [Full Speed Mode] [Manual Mode]
Duty % [50]
This item appears only when CPU FAN1&2 FRNT FAN1 mode is set to [Manual Mode].
This item allows you to configure the fan duty setting from 10% to 100%.
FRNT FAN2&3/4&5; REAR FAN1&2 mode [Generic Mode]
Allows you to configure the ASUS Smart Fan feature that smartly adjusts the fan speeds for
more efficient system operation.
Configuration options: [Generic Mode] [High Speed Mode] [Full Speed Mode] [Manual Mode]
5-46
Chapter 5: BIOS Setup
5.9
Security menu
This menu allows a new password to be created or a current password to be changed. The
menu also enables or disables the Secure Boot state and lets the user configure the System
Mode state.
Administrator Password
To set an administrator password:
1.
Select the Administrator Password item and press <Enter>.
2.
From the Create New Password box, key in a password, then press <Enter>.
3.
Confirm the password when prompted.
To change an administrator password:
1.
Select the Administrator Password item and press <Enter>.
2.
From the Enter Current Password box, key in the current password, then press
<Enter>.
3.
From the Create New Password box, key in a new password, then press <Enter>.
4.
Confirm the password when prompted.
To clear the administrator password, follow the same steps as in changing an administrator
password, but press <Enter> when prompted to create/confirm the password.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-47
User Password
To set a user password:
1.
Select the User Password item and press <Enter>.
2.
From the Create New Password box, key in a password, then press <Enter>.
3.
Confirm the password when prompted.
To change a user password:
1.
Select the User Password item and press <Enter>.
2.
From the Enter Current Password box, key in the current password, then press
<Enter>.
3.
From the Create New Password box, key in a new password, then press <Enter>.
4.
Confirm the password when prompted.
To clear a user password:
1.
Select the Clear User Password item and press <Enter>.
2.Select Yes from the Warning message window then press <Enter>.
Secure Boot Menu
This item allows you to customize the Secure Boot settings.
Secure Boot [Disabled]
Secure Boot can be enabled if the system is running in User mode with enrolled
platform Key (EPK) or if the CSM function is disabled.
Configuration options: [Disabled] [Enabled]
Secure Boot Mode [Custom]
Allows you to set the Secure Boot selector.
Configuration options: [Custom] [Standard]
5-48
Chapter 5: BIOS Setup
Key Management
This item only appears when the item Secure Boot Mode is set to [Custom]. The
Key Management item allows you to modify Secure Boot variables and set Key
Management page.
Default Key Provision [Disabled]
Configuration options: [Disabled] [Enabled]
Enroll All Factory Default Keys
This item will ask you if you want to Install Factory Default secure keys. Select Yes if
you want to load the default secure keys, otherwise select No.
Save All Secure Boot Variables
This item will ask you if you want to save all secure boot variables. Select Yes if you
want to save all secure boot variables, otherwise select No.
Platform Key (PK)/ Key Exchange Key (KEK)/ Authorized Signatures (DB)/Authorized
TimeStamps (DBT)/ Forbidden Signatures (DBX)
Configuration options: [Delete] [Set New] [Append]
Configuration options: [Set New] [Delete] [Append]
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-49
5.10
Boot menu
The Boot menu items allow you to change the system boot options.
Setup Prompt Timeout [xx]
Use the <+> and <-> keys to adjust the number of seconds to wait for setup activation key.
Bootup NumLock State [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
Boot Logo Display [Auto]
Allows you to enable or disable the full screen logo display feature.
Configuration options: [Auto] [Full Screen] [Disabled]
POST Report [5 sec]
Allows you to set the desired POST Report waiting time from 1 to 10 seconds.
Configuration options: [1 sec] ~ [10 sec] [Until Press ESC]
Chassis Intrusion [Warning]
Allows you to set an action when chassis intrusion has occurred.
Configuration options: [Warning] [Halt]
Boot Option Priorities
These items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of devices
installed in the system.
5-50
Chapter 5: BIOS Setup
•
To select the boot device during system startup, press <F8> when ASUS Logo
appears.
•
To access Windows OS in Safe Mode, please press <F8> after POST.
Set the booting order of network devices.
Boot Option #1/#2 [SATA P2: ASUS ...]
Configuration options: [SATA P2: ASUS ...] [SATA P3: WDC WD80...]
[AMI Virtual Floppy...] [IBA GE Slot 0700 v...]
CD/DVD ROM Drive BBS Priorities
Hard Drive BBS Priorities / Network Device BBS Priorities
These items appear only when you connect SATA ODD or hard drive to the SATA ports and
allow you to set the booting order of the SATA devices.
5.11
Tool menu
The Tool menu items allow you to configure options for special functions. Select an item then
press <Enter> to display the submenu.
ASUS EZ Flash
Allows you to run ASUS EZ Flash BIOS ROM Utility when you press <Enter>. Refer to the
ASUS EZ Flash Utility section for details.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-51
5.12
Exit menu
The Exit menu items allow you to save or discard your changes to the BIOS items.
Pressing <Esc> does not immediately exit this menu. Select one of the options from this
menu or <F10> from the legend bar to exit.
Save Changes & Reset
Exit System setup after saving the changes.
Discard Changes & Exit
Exit System setup without saving any changes.
Save Changes & Reset
Reset the system setup after saving the changes.
Discard Changes & Reset
Reset system setup without saving any changes.
Save Options
Save Changes
Save changes done so far to any of the setup options.
Discard Changes
Discard changes done so far to any of the setup options.
5-52
Chapter 5: BIOS Setup
Restore Defaults
Restore/load default values for all the setup options.
Save as User Defaults
Save the changes done so far as User Defaults.
Restore User Defaults
Restore the User Defaults to all the setup options.
Boot Override
These items displays the available devices. The device items that appears on the screen
depends on the number of devices installed in the system. Click an item to start booting from
the selected device.
Launch EFI Shell from filesystem device
Attempts to launch EFI Shell application (shellx64.efi) from one of the available filesystem
devices.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
5-53
5-54
Chapter 5: BIOS Setup
Chapter 6: RAID Configuration
RAID Configuration
This chapter provides instructions for setting up, creating, and
configuring RAID sets using the available utilities.
6
6.1
Setting up RAID
The motherboard supports the following SATA RAID solutions:
•
Intel® Rapid Storage Technology enterprise Option ROM Utility with RAID 0, RAID 1,
RAID 10, and RAID 5 support (for Windows OS only).
6.1.1
RAID definitions
RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in
parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a
sustained data transfer rate, double that of a single disk alone, thus improving data access
and storage. Use of two new identical hard disk drives is required for this setup.
RAID 1 (Data mirroring) copies and maintains an identical image of data from one drive to a
second drive. If one drive fails, the disk array management software directs all applications
to the surviving drive as it contains a complete copy of the data in the other drive. This RAID
configuration provides data protection and increases fault tolerance to the entire system. Use
two new drives or use an existing drive and a new drive for this setup. The new drive must be
of the same size or larger than the existing drive.
RAID 10 is data striping and data mirroring combined without parity (redundancy data) having
to be calculated and written. With the RAID 10 configuration you get all the benefits of both
RAID 0 and RAID 1 configurations. Use four new hard disk drives or use an existing drive and
three new drives for this setup.
RAID 5 stripes both data and parity information across three or more hard disk drives. Among
the advantages of RAID 5 configuration include better HDD performance, fault tolerance, and
higher storage capacity. The RAID 5 configuration is best suited for transaction processing,
relational database applications, enterprise resource planning, and other business systems.
Use a minimum of three identical hard disk drives for this setup.
6-2
•
If you want to boot the system from a hard disk drive included in a created RAID set,
copy first the RAID driver from the support DVD to a floppy disk before you install an
operating system to the selected hard disk drive.
•
Please refer to chapter 2 for how to select the RAID configuration utility. Move the
jumper to choose between LSI MegaRAID and Intel® Rapid RAID.
Chapter 6: RAID Configuration
6.1.2
Installing hard disk drives
The motherboard supports Serial ATA for RAID set configuration. For optimal performance,
install identical drives of the same model and capacity when creating a disk array.
To install the SATA hard disks for RAID configuration:
1.
Install the SATA hard disks into the drive bays following the instructions in the system
user guide.
2.
Connect a SATA signal cable to the signal connector at the back of each drive and to
the SATA connector on the motherboard.
3.
Connect a SATA power cable to the power connector on each drive.
6.1.3
Setting the RAID item in BIOS
You must set the RAID item in the BIOS Setup before you can create a RAID set from SATA
hard disk drives attached to the SATA connectors supported by
Intel® C602 chipset. To do this:
1.
Enter the BIOS Setup during POST.
2.
Go to the Advanced Menu > PCH SATA Configuration, then press <Enter>.
3.
Set SATA Mode to [RAID Mode]
4.
Press <F10> to save your changes and exit the BIOS Setup.
Refer to Chapter 4 for details on entering and navigating through the BIOS Setup.
6.1.4
RAID configuration utilities
Depending on the RAID connectors that you use, you can create a RAID set using the utilities
embedded in each RAID controller. For example, use the Intel® Rapid Storage Technology
if you installed Serial ATA hard disk drives on the Serial ATA connectors supported by the
Intel® C602 chipset.
Refer to the succeeding section for details on how to use the RAID configuration utility.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-3
6.2LSI Software RAID Configuration Utility
The LSI MegaRAID software RAID configuration utility allows you to create RAID 0,
RAID 1, or RAID 10 set(s) from SATA hard disk drives connected to the SATA connectors
supported by the motherboard southbridge chip.
To enter the LSI MegaRAID software RAID configuration utility:
1.
Turn on the system after installing all the SATA hard disk drives.
2.
During POST, the LSI MegaRAID software RAID configuration utility automatically
detects the installed SATA hard disk drives and displays any existing RAID set(s).
Press <Ctrl> + <M> to enter the utility.
LSI MegaRAID Software RAID BIOS Version A.10 09231523R
LSI SATA RAID Found at PCI Bus No:00 Dev No:1F
Device present at Port 0
ST3160812AS
152114MB
Device present at Port 1
ST3160812AS
152114MB
Device present at Port 2
ST3160812AS
152114MB
Device present at Port 3
ST3160812AS
152114MB
Press Ctrl-M or Enter to run LSI Software RAID Setup Utility.
•
The LSI MegaRAID software RAID configuration utility automatically configures to
RAID 1 when the SATA to RAID Mode is enabled.
•
The RAID setup screens shown in this section are for reference only and may not
exactly match the items on your screen due to the controller version difference.
•
When you create RAID sets with the LSI MegaRAID software RAID configuration
utility, the boot priority of the SATA optical drive has to be manually adjusted.
Otherwise, the system will not boot from the connected SATA ODD.
3.
The utility main window appears. Use the arrow keys to select an option from the
Management Menu and then press <Enter>. Refer to the Management Menu
descriptions on the next page.
At the bottom of the screen is the legend box. The keys on the legend box allow you
to navigate through the setup menu options or execute commands. The keys on the
legend box vary according to the menu level.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Configure VD(s)
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
6-4
Chapter 6: RAID Configuration
Menu
Description
Configure
Allows you to create RAID 0, RAID 1 or RAID 10 set using the Easy
Configuration or the New Configuration command. This menu also
allows you to view, add, or clear RAID configurations or select the
boot drive
Initialize
Allows you to initialize the virtual drives of a created RAID set
Objects
Allows you to initialize virtual drives or change the virtual drive
parameters
Rebuild
Allows you to rebuild failed drives
Check Consistency Allows you to check the data consistency of the virtual drives of a
created RAID set
6.2.1
Creating a RAID set
The LSI Software RAID Configuration Utility allows you to create a RAID 0, RAID 1, or RAID
10 set using two types of configurations: Easy and New.
In Easy Configuration, the virtual drive parameters are set automatically.
In New Configuration, you manually set the virtual drive parameters.
Using Easy Configuration
To create a RAID set using the Easy Configuration option:
1.
From the Management Menu, select Configure > Easy Configuration, and then press
<Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
Management
New Menu
Configuration
Configure View/Add Configuration
InitializeClear Configuration
Objects
Select Boot Drive
Rebuild
Check Consistency
Defines Physical Arrays. An Array Will Automatically Become A VD
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-5
2.
The ARRAY SELECTION MENU displays the available drives connected to the SATA
ports. Use the up/down arrow keys to select the drives you want to include in the RAID
set, and then press <Space>. When selected, the drive indicator changes from READY
to ONLIN A[X]-[Y], where X is the array number, and Y is the drive number.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Easy Configuration - ARRAY SELECTION MENU
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Port # 2 DISK
PORT #
0
ONLIN A00-00
1
ONLIN A00-01
2
READY
3
READY
74.74GB HDS728080PLA380
05.01C05
SPACE-Sel,ENTER-EndArray,F10-Configure,F2-Drive Info,F3-Virtual Drives,F4-HSP
•
The information of the selected hard disk drive displays at the bottom of the screen.
•
You need at least two identical hard disk drives when creating a RAID 1 set.
•
You need at least four identical hard disk drives when creating a RAID 10 set.
3.
Select all the drives required for the RAID set, and then press <F10> to configure array
setting.
4.
Press <Space> to select the configurable array.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Easy Configuration - ARRAY SELECTION MENU
SelectPORT
Configurable
Array(s)
#
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
A-0
0
ONLIN A00-00
1
ONLIN A00-01
2
READY
3
READY
SPAN-1
Cursor Keys, SPACE-(De)Select F2-Chidinfo F3-SlotInfo F10-Configure Esc-Quit
6-6
Chapter 6: RAID Configuration
5.
Press <F10> again, the virtual drive information appears including a Virtual Drive
menu that allows you to change the virtual drive parameters.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
LD
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU
RAID Configuration
Size
StripSz
Management Menu
Configure
0
Initialize
Objects
Rebuild
Check Consistency
1
148.580GB
PORT #
2
0
ONLIN A00-00
1
ONLIN A00-01
64KB
Status
ONLINE
2 0READY
Virtual Drive
RAID =
Units=
Size =
DWC =
RA
=
Accept
SPAN =
1
3
MB
152146MB
OFF
On
READY
NO
Choose RAID Level For This VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
6.
Select RAID from the Virtual Drive sub-menu, and then press <Enter>.
7.
Select the RAID level from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
LD
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU
RAID Configuration
Size
StripSz
Management Menu
Configure
0
Initialize
Objects
Rebuild
Check Consistency
1
148.580GB
PORT #
0
ONLIN A00-00
1
ONLIN A00-01
2 0READY
Virtual Drive
RAID =
Units=
Size =
DWC =
RA
=
Accept
SPAN =
2
1
3
MB
152146MB
OFF
On
READY
64KB
Status
ONLINE
RAID Level
RAID 0
RAID 1
NO
Choose RAID Level For This VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-7
8.
Select Units from the Virtual Drive sub-menu, and then press <Enter>.
9.
Select the units for virtual drive size from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
LD
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU
RAID Configuration
Size
StripSz
Management Menu
Configure
0
Initialize
Objects
Rebuild
Check Consistency
1
148.580GB
0
1
PORT #
2
1
3
MB
152146MB
OFF
On
Status
ONLINE
ONLIN A00-00
ONLIN
Select Units For VD Size
A00-01
MB
GB
TB
2 0READY
Virtual Drive
RAID =
Units=
Size =
DWC =
RA
=
Accept
SPAN =
64KB
READY
NO
Select Units For VD Size
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
10. When creating a RAID 1 or a RAID 10 set, select DWC from the Virtual Drive menu,
and then press <Enter>.
When creating a RAID 0 set, proceed to step 12.
11. Select On to enable the Disk Write Cache setting, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
LD
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU
RAID Configuration
Size
StripSz
Management Menu
Configure
0
Initialize
Objects
Rebuild
Check Consistency
1
148.580GB
PORT #
64KB
0
ONLIN A00-00
1
ONLIN A00-01
1
3
MB
152146MB
OFF
On
Status
ONLINE
Change DWC
2 0READY
Virtual Drive
RAID =
Units=
Size =
DWC =
RA
=
Accept
SPAN =
2
Off
On
READY
NO
Disk Write Cache Setting of VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
Enabling DWC can improve the performance, but with the risk of data loss.
6-8
Chapter 6: RAID Configuration
12. When finished setting the selected virtual drive configuration, select Accept from the
menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
LD
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU
RAID Configuration
Size
StripSz
Management Menu
Configure
0
Initialize
Objects
Rebuild
Check Consistency
1
148.580GB
PORT #
2
0
ONLIN A00-00
1
ONLIN A00-01
64KB
Status
ONLINE
Virtual Drive2 0READY
RAID =
Units=
Size =
DWC =
RA
=
Accept
SPAN =
1
3
MB
152146MB
OFF
On
READY
NO
Accept This VD Configuration And Go To Next VD
Cursor Keys, SPACE-(De) Select F2-ChIdInfo F3-SlotInfo F10-Configure Esc-Quit
13. Follow step 2 to 12 to configure additional virtual drives.
14. Press <Esc> to finish RAID configuration. When prompted to save configuration, select
Yes from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Configuration Menu
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
RAID
0
1
Easy Configuration
New Configuration
View/Add Configuration
Clear Configuration
Select Boot Drive
Save Configuration?
Yes
No
Virtual Drive(s) Configured
Size
#Stripes
StripSz
Status
148.580GB
ONLINE
2
64KB
Select Yes Or No
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-9
Using New Configuration
When a RAID set already exists, using the New Configuration command erases the
existing RAID configuration data. If you do not want to delete the existing RAID set, use the
View/Add Configuration command to view or create another RAID configuration.
To create a RAID set using the New Configuration option
1.
From the Management Menu, select Configure > New Configuration, and then press
<Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
Management MenuNew Configuration
Configure
View/Add Configuration
Initialize
Clear Configuration
Objects
Select Boot Drive
Rebuild
Check Consistency
Clear Existing Configuration And Start A New Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
Follow step 2 to 9 of the previous section: Using Easy Configuration.
3.
Select Size from the Virtual Drive menu, and then press <Enter>.
4.
Key-in the desired virtual drive size, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
LD
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU
RAID Configuration
Size
StripSz
Management Menu
Configure
0
Initialize
Objects
Rebuild
Check Consistency
1
148.580GB
PORT #
2
0
ONLIN A00-00
1
ONLIN A00-01
64KB
Status
ONLINE
Enter Virtual
VD Size: Drive
152146_
2 0READY
RAID =
Units=
Size =
DWC =
RA
=
Accept
SPAN =
1
3
MB
152146MB
OFF
On
READY
NO
Enter VD Size:
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
5.
6-10
Follow step 10 to 14 of the previous section: Using Easy Configuration to create the
RAID set.
Chapter 6: RAID Configuration
6.2.2
Adding or viewing a RAID configuration
You can add a new RAID configuration or view an existing configuration using the View/Add
Configuration command.
Adding a new RAID configuration
To add a new RAID configuration:
1.
From the Management Menu, select Configure > View/Add Configuration, and then
press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
Management MenuNew Configuration
Configure
View/Add Configuration
Initialize
Clear Configuration
Objects
Select Boot Drive
Rebuild
Check Consistency
View/Add to The Existing Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
The ARRAY SELECTION MENU displays the available drives connected to the SATA
ports. Select the drive(s) you want to include in the RAID set, then press <Space>.
When selected, the drive indicator changes from READY to ONLIN A[X]-[Y], where X
is the array number, and Y is the drive number.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
View/Add Configuration - ARRAY SELECTION MENU
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Port # 2 DISK
PORT #
0
ONLIN A00-00
1
ONLIN A00-01
2
READY
3
READY
77247MB
HDS72808PLA380
PF20A60A
SPACE-Sel,ENTER-EndArray,F10-Configure,F2-Drive Info,F3-Virtual Drives,F4-HSP
The information of the selected hard disk drive displays at the bottom of the screen.
3.
Follow step 3 to 12 of section 6.2.1 Creating a RAID set: Using Easy Configuration
to add a new RAID set.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-11
6.2.3
Initializing the virtual drives
After creating the RAID set(s), you must initialize the virtual drives. You may initialize the
virtual drives of a RAID set(s) using the Initialize or Objects command on the Management
Menu.
Using the Initialize command
To initialize the virtual drive using the Initialize command
1.
From the Management Menu, select Initialize, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Initialize VD(s)
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
2.
The screen displays the available RAID set(s) and prompts you to select the virtual
drive to initialize. Use the arrow keys to select the virtual drive from the Virtual Drive
selection, and then press <Space>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
0
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU
RAID Configuration
Size
StripSz
1
148.580GB
2
64KB
Status
ONLINE
Virtual Drives
Virtual Drive 0
Select VD
SPACE-(De)Select, F10-Initialize
6-12
Chapter 6: RAID Configuration
3.
Press <F10> to start initialization. When prompted, select Yes from the Initialize?
dialog box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
0
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU
RAID Configuration
Size
StripSz
1
148.580GB
2
64KB
Status
ONLINE
Initialize?
Yes
No
Virtual Drives
Virtual Drive 0
Init Will Destroy Data On Selected VD(s)
SPACE-(De)Select, F10-Initialize
Initializing a virtual drive erases all data on the drive.
4.
A progress bar appears on screen. If desired, press <Esc> to abort initialization. When
initialization is completed, press <Esc>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
RAID
Virtual Drive(s) Configured
Size
#Stripes
StripSz
Init
VD Is In Process
0
1 of 148.580GB
2
64KB
VD 0 Initialization Complete. Press Esc..
Status
ONLINE
100% Completed
Virtual Drives
Virtual Drive 0
SPACE-(De)Select, F10-Initialize
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-13
Using the Objects command
To initialize the virtual drives using the Objects command
1.
From the Management Menu, select Objects > Virtual Drive, and then press
<Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Rebuild
Check Consistency
Change VD Parameters
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
Select the virtual drive to initialize from the Virtual Drives sub‑menu, and then press
<Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Rebuild
Check Consistency
Virtual Drive(1)
Virtual Drive 0
Select VD
Press ENTER To Select A VD, <Del> To Delete A VD
6-14
Chapter 6: RAID Configuration
3.
Select Initialize from the pop-up menu, and then press <Enter> to start initialization.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Objects
Virtual Drive(1)
Virtual Drive 0
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Virtual Drive(0)
Rebuild
Initialize
Check Consistency
Check Consistency
View/Update Parameters
Initialize VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
4.
When prompted, press the <Space> to select Yes from the Initialize? dialog box, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Objects
Virtual Drive(1)
Virtual Drive 0
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Virtual Drive(0)
Rebuild
Initialize
Check Consistency
Initialize?
Check Consistency
Yes
View/Update Parameters
No
Init Will Destroy Data On Selected VD(s)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
5.
A progress bar appears on screen. If desired, press <Esc> to abort initialization. When
initialization is completed, press <Esc>.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-15
6.2.4
Rebuilding failed drives
You can manually rebuild failed hard disk drives using the Rebuild command in the
Management Menu.
To rebuild a failed hard disk drive
1.
From the Management Menu, select Rebuild, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Rebuild VD(s)
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
2.
The PHYSICAL DRIVES SELECTION MENU displays the available drives connected
to the SATA ports. Select the drive you want to rebuild, and then press <Space>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
REBUILD - PHYSICAL DRIVES SELECTION MENU
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Port # 1 DISK
PORT #
0
ONLIN A00-00
1
FAIL A00-01
77247MB
HDS72808PLA380
PF20A60A
SPACE-(De)Select,F10-Start Rebuild,F2-Drive Information,F3-View Virtual Drives
6-16
Chapter 6: RAID Configuration
3.
After selecting the drive to rebuild, press <F10>. When prompted, press <Y> to rebuild
the drive.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
REBUILD - PHYSICAL DRIVES SELECTION MENU
Management Menu
Configure
PORT #
Initialize
0 ONLIN A00-00
Objects
1 FAIL A00-01
Rebuild
Rebuilding
of Drive Will Take A Few Minutes. Start Rebuilding Drive (Y/N)?
Check Consistency
Port # 1 DISK
77247MB
HDS72808PLA380
PF20A60A
SPACE-(De)Select,F10-Start Rebuild,F2-Drive Information,F3-View Virtual Drives
4.
When rebuild is complete, press any key to continue.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-17
6.2.5
Checking the drives for data consistency
You can check and verify the accuracy of data redundancy in the selected virtual drive. The
utility can automatically detect and/or detect and correct any differences in data redundancy
depending on the selected option in the Objects > Adapter menu.
The Check Consistency command is available only for virtual drives included in a RAID 1
or RAID 10 set.
Using the Check Consistency Command
To check data consistency using the Check Consistency command
1.
From the Management Menu, select Check Consistency, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
CC of VD(s)
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
2.
The screen displays the available RAID set(s) and prompts you to select the virtual
drive to check. Press <Space> to select the virtual drive from the Virtual Drive submenu, and then press <F10>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
0
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU
RAID Configuration
Size
StripSz
1
148.580GB
2
64KB
Status
ONLINE
Virtual Drives
Virtual Drive 0
Select VD
SPACE-(De)Select, F10-Initialize
6-18
Chapter 6: RAID Configuration
3.
When prompted, use the arrow keys to select Yes from the Consistency Check?
dialog box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
0
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU Status
RAID Configuration
Size
StripSz
10
154494MB
2
64KB
ONLINE
Consistency Check?
Yes
No
Virtual Drives
Virtual Drive 0
Select VD(s)
SPACE-(De)Select, F10-Initialize
A progress bar appears on screen.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Virtual Drive(s) Configured
Easy
-#Stripes
ARRAY SELECTION
MENU Status
RAID Configuration
Size
StripSz
10 CC154494MB
64KB
ONLINE
Under Process2
VD 0 Consistency Check. Press Esc to Abort.
LD
0
85% Completed
Virtual Drives
Virtual Drive 0
The Data On The Drives Is Inconsistency. Repair Done!
SPACE-(De)Select, F10-Initialize
4.
While checking the disk consistency, press <Esc> to display the following options.
• Stop
• Continue - Continues the consistency check.
• Abort
5.
When checking is complete, press any key to continue.
- Stops the consistency check. The utility stores the percentage of
disk checked, and when you restart checking, it continues from the
last percentage completed rather than from zero percent.
- Aborts the consistency check. When you restart checking, it
continues from zero percent.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-19
Using the Objects command
To check data consistency using the Objects command
6-20
1.
From the Management Menu, select Objects, and then select Virtual Drive from the
sub-menu.
2.
Use the arrow keys to select the virtual drive you want to check, and then press
<Enter>.
3.
Select Check Consistency from the pop-up menu, and then press <Enter>.
4.
When prompted, use the arrow keys to select Yes from the dialog box to check the
drive.
5.
When checking is complete, press any key to continue.
Chapter 6: RAID Configuration
6.2.6
Deleting a RAID configuration
To delete a RAID configuration
1.
From the Management Menu, select Configure > Clear Configuration, and then
press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
Management MenuNew Configuration
Configure
View/Add Configuration
Initialize
Clear Configuration
Objects
Select Boot Drive
Rebuild
Check Consistency
Clear Existing Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
When prompted, use the arrow keys to select Yes from the Clear Configuration?
dialog box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
Management MenuNew Configuration
Configure
View/Add Configuration
Initialize
Clear Configuration
Clear Configuration?
Objects
Select Boot
Yes Drive
Rebuild
No
Check Consistency
Clear Existing Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
The utility clears all the current array(s).
3.
Press any key to continue.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-21
6.2.7
Selecting the boot drive from a RAID set
You must have created a new RAID configuration before you can select the boot drive from a
RAID set. See section 6.2.1 Creating a RAID set: Using New Configuration for details.
To select the boot drive from a RAID set
1.
From the Management Menu, select Configure > Select Boot Drive, and then press
<Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
Management MenuNew Configuration
Configure
View/Add Configuration
Initialize
Clear Configuration
Objects
Select Boot Drive
Rebuild
Check Consistency
Select A Boot VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
When prompted, use the arrow keys to select the bootable virtual drive from the list,
then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
VDs(1): Current Boot VD(0)
Configuration Bootable
Menu
Boot Drive 0
Easy Configuration
Management MenuNew Configuration
Configure
View/Add Configuration
Initialize
Clear Configuration
Objects
Select Boot Drive
Rebuild
Check Consistency
Select A Boot VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
3.
6-22
The virtual drive is selected as boot drive. Press any key to continue.
Chapter 6: RAID Configuration
6.2.8
Enabling WriteCache
You may manually enable the RAID controller’s WriteCache option after creating a RAID set
to improve the data transmission performance.
When you enable WriteCache, you may lose data when a power interruption occurs while
transmitting or exchanging data among the drives.
The WriteCache function is recommended for RAID 1 and RAID 10 sets.
To enable WriteCache
1.
From the Management Menu, select Objects > Adapter, select an existing adapter,
and then press <Enter> to display the adapter properties.
2.
Select Disk WC, and then press <Enter> to turn on the option.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Adapter 0
Rebuild Rate
=
Chk Const Rate =
Management Menu
Adapter
FGI Rate
=
Configure
Virtual Drive BGI Rate
=
Initialize
Physical Drive Disk WC
=
Objects
Read Ahead
=
Rebuild
Bios State
=
Check Consistency
Cont On Error =
Fast Init
=
Auto Rebuild
=
Auto Resume
=
Disk Coercion =
Factory Default
Objects
30
30
30
30
Off
On
Enable
Yes
Enable
On
Enable
1GB
Disk Write Cache - Off(Write Through or On(Write Back)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
3.
From the Management Menu, select Objects > Virtual Drive, select an existing
adapter and press <Enter>. Select View/Update Parameters and press <Enter> to
display the adapter properties.
4.
Select Disk WC, and then press <Enter> to turn on the option.
LSI Software RAID Configuration Utility Ver C.05 Sep 17,2010
BIOS Version A.10.09231523R
Virtual Drive
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Rebuild
Check Consistency
RAID
Size
Stripe Size
#Stripes
State
Spans
Disk WC
Read Ahead
=
=
=
=
=
=
=
=
0
148.580GB
64KB
2
OPTIMAL
1
On
On
Disk Write Cache Setting of VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
5.
When finished, press any key to continue.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-23
6.3Intel® Rapid Storage Technology enterprise SATA
Option ROM Utility
The Intel® Rapid Storage Technology enterprise SATA Option ROM utility allows you to
create RAID 0, RAID 1, RAID 10 (RAID 1+0), and RAID 5 set from Serial ATA hard disk
drives that are connected to the Serial ATA connectors supported by the Southbridge.
Before you proceed, ensure that you have installed the Serial ATA hard disk drives, have
set the correct jumper settings of the motherboard, and have set the correct SATA mode in
the BIOS setup. You can refer to sections Installing hard disk drives, Setting Jumpers,
and Setting the RAID mode in BIOS for more information.
To launch the Intel® Rapid Storage Technology enterprise SATA Option ROM utility:
1.
Turn on the system.
2.
During POST, press <Ctrl>+<I> to display the utility main menu.
Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023
Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non-RAID
4. Exit
[ DISK/VOLUME INFORMATION]
RAID Volumes:
None defined.
Physical Disks:
ID Drive Model
0
ST3300656SS
1
ST3300656SS
2
ST3300656SS
3
ST3300656SS
[
]-Select
Serial #
HWAS0000991753TR
37VN00009846RAJ1
397600009846UEDY
GWC50000991756G6
[ESC]-Exit
Size
279.3GB
279.3GB
279.3GB
279.3GB
Type/Status(Vol ID)
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
[ENTER]-Select Menu
The navigation keys at the bottom of the screen allow you to move through the menus
and select the menu options.
The RAID BIOS setup screens shown in this section are for reference only and may not
exactly match the items on your screen.
6-24
Chapter 6: RAID Configuration
6.3.1
Creating a RAID set
To create a RAID set:
1.
From the utility main menu, select 1. Create RAID Volume and press <Enter>.
2.
Key in a name for the RAID set and press <Enter>.
Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023
Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
[ CREATE VOLUME MENU ]
Name: Volume0
RAID Level: RAID0(Strips)
Disks: Select Disks
Strip Size: 128KB
Capacity: 0.0 GB
Syne: N/A
Create Volume
[ HELP ]
Enter a unique volume name that has no special characters and is
16 characters or less.
[
]Change
[TAB]-Next
[ESC]-Previous Menu
[ENTER]-Select
3.
Press the up/down arrow keys to select a RAID Level that you wish to create then
press <Enter>.
4.
From the Disks item field, press <Enter> to select the hard disk drives that you want to
include in the RAID set.
[ SELECT DISKS ]
Port
0
1
2
3
Drive Model
ST3300656SS
ST3300656SS
ST3300656SS
ST3300656SS
Serial #
HWAS0000991753TR
37VN00009846RAJ1
397600009846UEDY
GWC50000991756G6
Size
279.3GB
279.3GB
279.3GB
279.3GB
Status
Non-RAID
Non-RAID
Non-RAID
Non-RAID
Disk
Disk
Disk
Disk
Select 1 Master and 1 Recovery disk to create volume.
[
5.
]-Prev/Next [TAB]-(M)aster [SPACE]-(R)ecovery [ENTER]-Done
Use the up/down arrow keys to move the selection bar then press <Space> to select a
disk. A small triangle before the Port number marks the selected drive. Press <Enter>
when you are done.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-25
6.
Use the up/down arrow keys to select the stripe size for the RAID array (for RAID 0,
10 and 5 only) then press <Enter>. The available stripe size values range from 4 KB to
128 KB. The following are typical values:
RAID 0: 128KB
RAID 10: 64KB
RAID 5: 64KB
We recommend a lower stripe size for server systems, and a higher stripe size for
multimedia computer systems used mainly for audio and video editing.
7.
In the Capacity field item, key in the RAID volume capacity that you want to use and
press <Enter>. The default value field indicates the maximum allowed capacity.
8.
Press <Enter> to start creating the RAID volume.
9. From the following warning message, press <Y> to create the RAID volume and return
to the main menu, or press <N> to go back to the CREATE VOLUME menu.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
6-26
Chapter 6: RAID Configuration
6.3.2
Deleting a RAID set
Take caution when deleting a RAID set. You will lose all data on the hard disk drives when
you delete a RAID set.
To delete a RAID set:
1.
From the utility main menu, select 2. Delete RAID Volume and press <Enter>.
2.
From the Delete Volume Menu, press the up/down arrow keys to select the RAID set
you want to delete then press <Del>.
Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023
Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
[ DELETE VOLUME MENU ]
Name
Volume0
Level
RAID0(Stripe)
Drives
2
Capacity
298.0GB
Status
Normal
Bootable
Yes
[ HELP ]
Deleting a volume will reset the disks to non-RAID
WARNING: ALL DISK DATA WILL BE DELETED.
(This does not apply to Recovery volumes)
[
3.
]-Select
[ESC]-Previous Menu
[DEL]-Delete Volume
Press <Y> to confirm deletion of the selected RAID set and return to the utility main
menu, or press <N> to return to the DELETE VOLUME menu.
[ DELETE VOLUME VERIFICATION ]
ALL DATA IN THE VOLUME WILL BE LOST!
(This does not apply to Recovery volumes)
Are you sure you want to delete volume “Volume0”? (Y/N):
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-27
6.3.3
Resetting disks to Non-RAID
Take caution before you reset a RAID volume hard disk drive to non-RAID. Resetting a
RAID volume hard disk drive deletes all internal RAID structure on the drive.
To reset a RAID set:
1.
From the utility main menu, select 3. Reset Disks to Non-RAID and press <Enter>.
2.
Press the up/down arrow keys to select the drive(s) or disks of the RAID set you want
to reset, then press <Space>. A small triangle before the Port number marks the
selected drive. Press <Enter> when you are done.
[ RESET RAID DATA ]
Resetting RAID disk will remove its RAID structures
and revert it to a non-RAID disk.
WARNING: Resetting a disk causes all data on the disk to be lost.
(This does not apply to Recovery volumes)
Port
0
1
Drive Model
ST3300656SS
ST3300656SS
Serial #
HWAS0000991753TR
37VN00009846RAJ1
Size
279.3GB
279.3GB
Status
Member Disk
Member Disk
Select the disks that should be reset.
[
3.
6-28
]-Previous/Next [SPACE]-Selects [ENTER]-Selection Complete
Press <Y> in the confirmation window to reset the drive(s) or press <N> to return to the
utility main menu.
Chapter 6: RAID Configuration
6.3.4
Exiting the Intel® Rapid Storage Technology enterprise
SATA Option ROM utility
To exit the utility:
1.
From the utility main menu, select 4. Exit then press <Enter>.
2.
Press <Y> to exit or press <N> to return to the utility main menu.
[ CONFIRM EXIT ]
Are you sure you want to exit? (Y/N):
6.3.5
Rebuilding the RAID
This option is only for the RAID 1 set.
Rebuilding the RAID with other non-RAID disk
If any of the SATA hard disk drives included in the RAID 1 array failed, the system displays
the status of the RAID volume as “Degraded” during POST. You can rebuild the RAID array
with other installed non-RAID disks.
To rebuild the RAID with other non-RAID disk:
1.
During POST, press <Ctrl>+<I> at the prompt to enter the Intel Rapid Storage
Technology option ROM utility.
2.
If there is a non-RAID SATA Hard Disk available, the utility will prompt you to rebuild
the RAID. Press the up/down arrow keys to select the destination disk then Press
<Enter> to start the rebuilding process, or press <ESC> to exit.
[ DEGRADED VOLUME DETECTED ]
“Degraded” volume and disk available for rebuilding detected. Selectign
a disk initiates a rebuild. Rebuild completes in the operating system.
Select the port of destination disk for rebuilding (ESC to exit):
Port Drive Model
Serial #
Size
X
XXXXXXXXXXX
XXXXXXXX
XXX.GB
[
]-Previous/Next [ENTER]-Select [ESC]-Exit
Select a destination disk with the same size as the original hard disk.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-29
3.
The utility immediately starts rebuilding after the disk is selected. When done, the
status of the degraded RAID volume is changed to “Rebuild”.
Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023
Copyright(C) 2003-12 Intel Corporation. All Rights Reserved.
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non-RAID
4. Exit
[ DISK/VOLUME INFORMATION]
RAID Volumes:
ID
Name
1
Volume0
Level1
RAID1(Mirror)
Physical Devices:
Port Drive Model
1
ST3160812AS
2
ST3160812AS
Strip
N/A
Serial #
9LS0F4HL
3LS0JYL8
Size
149.0GB
Size
149.0GB
149.0GB
*=Data is Encrypted
Status
Bootable
Rebuild
Yes
Type/Status(Vol ID)
Member Disk(0)
Member Disk(0)
Volumes with “Rebuild” status will be rebuilt within the operating system.
[
]-Select
[ESC]-Exit
[ENTER]-Select Menu
4.
Press <Esc> to exit Intel Rapid Storage Technology and reboot the system.
5.
Select Start > Programs > Intel Rapid Storage > Intel Rapid Storage Console or
click the Intel Rapid Storage Technology tray icon to load the Intel Rapid Storage
Manager utility.
6.
From the View menu, select Advanced Mode to display the details of the Intel Rapid
Storage Console.
7.
From the Volumes view option, select RAID volume to view the rebuilding status.
When finished, the status is changed to “Normal”.
Rebuilding the RAID with a new hard disk
If any of the SATA hard disk drives included in the RAID array failed, the system displays the
status of the RAID volume as “Degraded” during POST. You may replace the disk drive and
rebuild the RAID array.
To rebuild the RAID with a new hard disk:
1.
Remove the failed SATA hard disk and install a new SATA hard disk of the same
specification into the same SATA Port.
Select a destination disk with the same size as the original hard disk.
2.
6-30
Reboot the system then follow the steps in section Rebuilding the RAID with other
non-RAID disk.
Chapter 6: RAID Configuration
6.3.6
Setting the Boot array in the BIOS Setup Utility
You can set the boot priority sequence in the BIOS for your RAID arrays when creating multiRAID using the Intel® Rapid Storage Technology enterprise SATA Option ROM utility.
To set the boot array in the BIOS:
Set at least one of the arrays bootable to boot from the hard disk.
1.
Reboot the system and press <Del> to enter the BIOS setup utility during POST.
2.
Go to the Boot menu and select the boot option priority.
3.
Use up/down arrow keys to select the boot priority and press <Enter>. See the Boot
menu section of Chapter 4 for more details.
4.
From the Exit menu, select Save Changes & Exit, then press <Enter>.
5.
When the confirmation window appears, select Yes, then press <Enter>.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-31
6.4
Intel® Rapid Storage Technology enterprise
(Windows)
The Intel® Rapid Storage Technology enterprise allows you to create RAID 0, RAID 1, RAID
10 (RAID 1+0), and RAID 5 set(s) from Serial ATA hard disk drives that are connected to the
Serial ATA connectors supported by the Southbridge.
You need to manually install the Intel® Rapid Storage Technology enterprise utility on a
Windows® operating system. Please refer to the installation instructions in Chapter 6.
To enter the Intel® Rapid Storage Technology enterprise utility under Windows operating
system:
1.
Turn on the system and go to the windows desktop.
2.
Click the Intel® Rapid Storage Technology enterprise icon to display the main menu.
Your storage system is configured for data protection, increased performance and
optimal data storage capacity. You can create additional volumes to further optimize
your storage system.
You can click Rescan to re-scan any attached hard disks.
6-32
Chapter 6: RAID Configuration
6.4.1
Creating a RAID set
To create a RAID set:
1.
From the utility main menu, select Create Volume and select volume type.
2.
Click Next.
3.
Enter a name for the RAID set, then select the array disks.
4.
Select Volume Size tab, you can drag the bar to decide the volume size.
5.
Click Next.
•
If you do not want to keep the data on one of the selected disks, select NO when
prompted.
•
If you want to Enable volume write-back cache or Initialize volume, click
Advanced.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-33
6.
Confirm the volume creation, than click Create Volume to continue.
This process could take a while depending on the number and size of the disks. You can
continue using other applications during this time.
7. Wait until the process is completed, then click OK when prompted.
You still need to partition your new volume using Windows Disk Management before
adding any data.
The RAID set is displayed in the Volumes list and you can change the settings in Volume
Properties.
6-34
Chapter 6: RAID Configuration
6.4.2
Changing a Volume Type
To change the volume type in Volume Properties:
1.
Click the SATA array items you want to change in Volumes field.
2
From the Volume Properties field, select Type:RAID 1 Change type.
3.
You can change the Name, Select the new volume type, and Select additional
disks to include in the new volume if needed.
4.
Select the Data stripe size for the RAID array (for RAID 0, 10 and 5 only), and click
OK. The available stripe size values range from 4 KB to 128 KB. The following are
typical values:
RAID 0: 128KB
RAID 10: 64KB
RAID 5: 64KB
We recommend a lower stripe size for server systems, and a higher stripe size for
multimedia computer systems used mainly for audio and video editing.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-35
6.4.3
Deleting a volume
Be cautious when deleting a volume. You will lose all data on the hard disk drives. Before
you proceed, ensure that you back up all your important data from your hard drives.
To delete a volume:
6-36
1.
From the utility main menu, select the volume (exp. Volume_0000) in Volumes field
you want to delete.
2.
Select Delete volume in Volume Properties field. The following screen appears.
3.
Click Yes to delete the volume and return to the utility main menu, or click No to return
to the main menu.
Chapter 6: RAID Configuration
6.4.4Preferences
System Preferences
Allow you to set to show the notification area icon and show system information, warning, or
errors here.
E-Mail Preferences
Allow you to set to sent e-mail of the following events:
•
Storage system information
•
Storage system warnings
•
Storage system errors
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
6-37
6-38
Chapter 6: RAID Configuration
Chapter 7: Driver Installation
Driver Installation
This chapter provides the instructions for installing the
necessary drivers for different system components in both
Linux® and Windows® Operating Systems.
7
7.1
RAID driver installation
After creating the RAID sets for your server system, you are now ready to install an
operating system to the independent hard disk drive or bootable array. This part provides the
instructions on how to install the RAID controller drivers during OS installation.
7.1.1
Creating a RAID driver disk
The system does not include a floppy drive. You have to use a USB floppy drive when
creating a SATA RAID driver disk.
If you have created RAID sets with the LSI Software RAID configuration utility, the boot
priority of the SATA optical disk drive has to be manually adjusted. Otherwise, the system
will not boot from the connected SATA ODD.
A floppy disk with the RAID driver is required when installing Windows® XP / Server 2003 or
Linux operating system on a hard disk drive that is included in a RAID set. You can create a
RAID driver disk in DOS (using the Makedisk application in the support DVD).
To create a RAID driver disk in DOS environment
1.
Place the motherboard support DVD in the optical drive.
2.
Restart the computer, and then enter the BIOS Setup.
3.
Select the optical drive as the first boot priority to boot from the support DVD. Save
your changes, and then exit the BIOS Setup.
4.
Restart the computer.
5.
From the Create Driver Diskette Menu, use the arrow keys to select a sub-menu. To
create the RAID driver disk, select C610 INTEL RAID Driver then press <Enter>.
Create Driver Diskette Menu
C610 INTEL RAID Driver
Write DMI
FreeDOS command prompt
7-2
6.
Locate the RAID driver you need then place a blank, high-density floppy disk to the
floppy disk drive.
7.
Press <Enter>.
8.
Follow screen instructions to create the driver disk.
Chapter 7: Driver Installation
To create a RAID driver disk in Windows® environment
1. Start Windows®.
2. Place the motherboard support DVD into the optical drive.
3. Go to the Make disk menu, and then select the type of RAID driver disk you want to
create.
4. Insert a floppy disk into the USB floppy disk drive.
5. Follow succeeding screen instructions to complete the process.
Write-protect the floppy disk to avoid computer virus infection.
To create a RAID driver disk in Red Hat® Enterprise Linux server environment
1.
Insert a blank formatted high-density floppy disk to the USB floppy disk drive.
2.Type dd if=XXX.img of=/dev/fd0 to decompress the file into the floppy disk from
the following path in the support DVD:
For LSI MegaRAID Driver
3. \Drivers\C60x LSI RAID\Driver\makedisk\Linux
Eject the floppy disk.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-3
7.1.2
Installing the RAID controller driver
During Windows® Server 2008 OS installation
To install the RAID controller driver when installing Windows® Server 2008 OS
1.
Boot the computer using the Windows® Server 2008 OS installation disc. Follow the
screen instructions to start installing Windows Server 2008.
2.
When prompted to choose a type of installation, click Custom (advanced).
3.Click Load Driver.
7-4
Chapter 7: Driver Installation
4.
A message appears, reminding you to insert the installation media containing the driver
of the RAID controller driver. If you have only one optical drive installed in your system,
eject the Windows OS installation disc and replace with the motherboard Support DVD
into the optical drive. Click Browse to continue.
5.
Locate the driver in the corresponding folder of the Support DVD then click OK to
continue.
6.
Select the RAID controller driver you need from the list and click Next.
7.
When the system finishes loading the RAID driver, replace the motherboard Support
DVD with the Windows Server installation disc. Select the drive to install Windows and
click Next.
8.
Setup then proceeds with the OS installation. Follow screen instructions to continue.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-5
Red Hat® Enterprise Linux OS 5.6
To install the LSI MegaRAID controller driver when installing Red Hat® Enterprise OS:
1.
Boot the system from the Red Hat® OS installation CD.
2.
At the boot:, type linux dd noprobe=ata1 noprobe=ata2..., then press
<Enter>.
The number of ata varies with the hard disk drive number you have when building a RAID
set. For example, if you want to build a RAID set with 6 hard disk drives, type command
line: linux dd noprobe=ata1 noprobe=ata2 noprobe=ata3 noprobe=ata4 noprobe=ata5
noprobe=ata6.
- To install or upgrade in graphical mode, press the <ENTER> key.
- To install or upgrade in text mode, type: linux text <ENTER>.
- Use the function keys listed below for more information.
[F1-Main] [F2-Options] [F3-General] [F4-Kernel] [F5-Rescue]
boot: linux dd noprobe=ata1 noprobe=ata2
3.Select Yes using the <Tab> key when asked if you have the driver disk, then press
<Enter>.
Main Menu
Do you have a driver disk?
Yes
4.
No
Insert the Red Hat® Enterprise RAID driver disk to the USB floppy disk drive, select
OK, then press <Enter>.
Insert Driver Disk
Insert your driver disk into /dev/fd0
and press “OK” to continue.
OK
7-6
Back
The drivers for the RAID card are installed to the system.
Chapter 7: Driver Installation
5.
When asked if you will load additional RAID controller drivers, select No, then press
<Enter>.
More Driver Disks?
Do you wish to load any more
driver disks?
Yes
No
6.
Follow the onscreen instructions to finish the OS installation.
7.
When the installation is completed, DO NOT click Reboot. Press <Ctrl> + <Alt> + <F2>
to switch to the command-line interface from graphic user interface.
8.
Type the following commands when using a Legacy floppy.
mkdir /mnt/driver
mount /dev/fd0 /mnt/driver
cd /mnt/driver
sh replace_ahci.sh
reboot
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-7
Red Hat® Enterprise Linux OS 6.1
To install the LSI MegaRAID controller driver when installing Red Hat® Enterprise OS:
7-8
1.
Boot the system from the Red Hat® OS installation CD.
2.
Press <Tab> to edit options.
3.
While booting from DVD, press <ESC> to give the third party driver. Enter the following
command at the boot: Linux dd blacklist=isci blacklist=ahci nodmraid,
then press <ENTER>.
Chapter 7: Driver Installation
4.
Select Yes using the <Tab> key when asked if you have the driver disk, then press
<Enter>.
Main Menu
Do you have a driver disk?
Yes
No
5 . You have multiple devices which could serve as source for a driver disk. Choose one
you like to use and select OK, then press <Enter>.
Driver Disk Sou8rce
You have multiple devices which could
serve as source for a driver disk.
Which would you like to use?
sdc
sdd
sdb
sr0
OK
Cancel
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-9
6.
Insert the Red Hat® Enterprise RAID driver disk to the USB floppy disk drive, select
OK, then press <Enter>.
Insert Driver Disk
Insert your driver disk into /dev/sdb
and press “OK” to continue.
OK
Back
The drivers for the RAID card are installed to the system.
7.
When asked if you will load additional RAID controller drivers, select No, then press
<Enter>.
More Driver Disks?
Do you wish to load any more
driver disks?
Yes
8.
7-10
No
Follow the onscreen instructions to finish the OS installation.
Chapter 7: Driver Installation
Preparing the Linux Driver
Ensure that there is another computer with a Linux-based OS to create the RAID driver. When
creating the RAID driver, you may refer to the examples below which uses a 64bit SUSE Linux
system to create a 64bit RAID driver for SUSE11 sp1.
1. Copy the image file into the Linux system.
Example: megasr-15.00.0120.2012-1-sles11-ga-x86_64.img
2.
Create a folder.
Example: image
3.
Mount the image file into the image folder using this command format:
mount -oloop [image file name] image
Example: mount -oloop megasr-15-15.00.0120.2012-1-sles11ga-x86__64.img image
4.
Copy the contents of the image directory, labeled as 01, into a FAT32 USB drive.
5.
Rename the 01 folder to CD Image.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-11
Installing SUSE 11 Linux OS
To install the LSI MegaRAID controller driver when installing SUSE Linux Enterprise
Server OS:
7-12
1.
Boot the system from the SUSE OS installation CD.
2.
Use the arrow keys to select Installation from the Boot Options menu.
3.
Press <F6>, then select Yes from the menu. Press <Enter>.
Chapter 7: Driver Installation
4.
Use the USB drive to provide the third-party driver during the OS installation. Type the
command brokenmodules=ahci in Boot Options field, and press <Enter>.
5.
When below screen appears, select the USB floppy disk drive (sda) as the driver
update medium. Select OK, then press <Enter>.
Please choose the Driver Update medium.
sda: USB Floppy
other device
OK
Back
6.Select Back and follow the onscreen instructions to finish the installation.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-13
7.2
Management applications and utilities installation
The support DVD that is bundled with your motherboard contains drivers, management
applications, and utilities that you can install to maximize the features of your
motherboard.
7.3
1.
The contents of the support DVD are subject to change at any time without notice.
Visit the ASUS website (www.asus.com) for the latest updates on software and
utilities.
2.
The support DVD is supported on Windows® Server 2008 R2 and Windows®
Server 2012.
Running the Support DVD
When you place the support DVD into the optical drive, the DVD automatically displays
the main screen if Autorun is enabled in your computer. By default, the Drivers tab is
displayed.
If Autorun is NOT enabled in your computer, browse the contents of the support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to
run the support DVD.
The main screen of the Support DVD contains the following tabs:
1.Drivers
2.
Utilities
3. MakeDisk
4.Manual
5.Contact
The main screen of the Support DVD looks exactly the same on the Windows® Server
2008 R2 and on the Windows® Server 2012 Operating System (OS).
7-14
Chapter 7: Driver Installation
7.3.1
Drivers menu tab
The Drivers Menu shows the available device drivers if the system detects installed devices.
Install the necessary drivers to activate the devices.
7.3.2
Utilities menu tab
The Utilities menu displays the software applications and utilities that the motherboard supports.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-15
7.3.3
MakeDisk menu tab
The MakeDisk menu contains items to create the Intel RAID driver disks.
Press the arrow down button in the lower part of the menu to view more items.
7.3.4
Manual menu
The Manual menu provides the link to the Broadcom NetXtreme II Network Adapter
user guide.
You need an internet browser installed in your OS to view the User Guide.
7-16
Chapter 7: Driver Installation
7.3.5
Contact information menu
The Contact menu displays the ASUS contact information, e-mail addresses, and
useful links if you need more information or technical support for your motherboard.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-17
7.4Intel® chipset device software installation
This section provides the instructions on how to install the Intel® chipset device software on
the system.
You need to manually install the Intel® chipset device software on a Windows operating
system.
To install the Intel® chipset device software:
1.
Restart the computer, and then log on with Administrator privileges.
2.
Insert the motherboard/system support DVD to the optical drive. The support DVD
automatically displays the Drivers menu if Autorun is enabled in your computer.
If Autorun is NOT enabled in your computer, browse the contents of the support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the support DVD.
3.
Click the item Intel Chipset Device Software from the menu.
4.The Intel(R) Chipset Device Software window appears. Click Next to start
installation.
7-18
Chapter 7: Driver Installation
5.Select Yes to accept the terms of the License Agreement and continue the process.
6.
Read the Readme File Information and press Next to continue the installation.
7.Toggle Yes, I want to restart the computer now and click Finish to complete the
setup process.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-19
7.5
Installing the Intel® I350-AM1/I350-AM2/I210 X540-BT2 Gigabit Adapters driver
This section provides the instructions on how to install the Intel® I350-AM1/I350-AM2/
I210/X540-BT2 Gigabits Adapter Driver on the system.
To install the Intel® I350-AM1/I350-AM2/I210/X540-BT2 Gigabit Adapters Driver on the
Windows® operating system:
1.
Restart the computer.
2. Log on with Administrator privileges.
3.
Insert the motherboard/system support DVD to the optical drive.
If Autorun is NOT enabled in your computer, browse the contents of the support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the support DVD.
4.Click Intel® I350-AM1/I350-AM2/I210/X540-BT2 Gigabit Adapters Drivers in the
Drivers menu of the main screen to start the installation.
5.Click Install Drivers and Software option to begin installation.
7-20
Chapter 7: Driver Installation
6.Click Next when the Intel(R) Network Connections–InstallShield Wizard window
appears.
7.Tick I accept the terms in the license agreement and click Next to continue.
8.
From the Setup Options window, click Next to start the installation.
By default, Intel(R) PROSet for Windows Device Manager and Windows PowerShell
Module are ticked.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-21
9.Click Install to start the installation.
10. When the installation is done, press Finish to complete the installation.
7-22
Chapter 7: Driver Installation
7.6
VGA driver installation
This section provides the instructions on how to install the ASPEED Video Graphics Adapter
(VGA) driver.
You need to manually install the ASPEED VGA driver on a Windows® operating system.
To install the ASPEED VGA driver:
1.
Restart the computer, and then log on with Administrator privileges.
2.
Insert the motherboard/system support DVD to the optical drive. The support DVD
automatically displays the Drivers menu if Autorun is enabled in your computer.
If Autorun is NOT enabled in your computer, browse the contents of the support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the support DVD.
3.
Click the ASPEED AST2300 / AST2400 Display Driver to begin installation.
4.
From the installation window, click Next to start the installation.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-23
5.Click Install to proceed with the installation.
6.Click Finish to complete the installation.
7-24
Chapter 7: Driver Installation
7.7Intel® Rapid Storage Technology enterprise 4.0 installation
This section provides the instructions on how to install the Intel® Rapid Storage Technology
enterprise 4.0 on the system.
You need to manually install the Intel® Rapid Storage Technology enterprise 4.0 utility on a
Windows® operating system.
To install the Intel® Rapid Storage Technology enterprise 4.0 utility:
1.
Restart the computer, and then log on with Administrator privileges.
2.
Insert the motherboard/system support DVD to the optical drive, and find the utility
menu.
3.
Click the Intel® Rapid Storage Technology enterprise 4.0 to begin installation.
4.
When the Welcome to the Setup Program appears, click Next to start the installation.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-25
7-26
5.
Read the Warning message and click Next to continue.
6.
Read the License Agreement and click Yes to continue.
7.
Read the Readme File Information and click Next to continue.
Chapter 7: Driver Installation
8.
After completing the installation, click Next to complete the setup process.
9.Select Yes, I want to restart my computer now and click Finish to restart your
computer before using the program.
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
7-27
7-28
Chapter 7: Driver Installation
Appendices
Contact Information
A
ASUS contact information
ASUSTeK COMPUTER INC.
Address
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
Telephone +886-2-2894-3447
Fax +886-2-2890-7798
E-mailinfo@asus.com.tw
Web site
http://www.asus.com.tw
Technical Support
Telephone Fax Online Support
+86-21-38429911
+86-21-58668722 ext: 9101
http://support.asus.com/techserv/techserv.aspx
ASUSTeK COMPUTER INC. (Taiwan)
Address
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
Telephone +886-2-2894-3447
Fax +886-2-2890-7798
E-mailinfo@asus.com.tw
Web site
http://www.asus.com.tw
Technical Support
Telephone Online Support
+886-2-2894-3447 (0800-093-456)
http://support.asus.com/techserv/techserv.aspx
ASUSTeK COMPUTER INC. (China)
Address
Telephone Fax Web site
No.508, Chundong Road, Xinzhuang Industrial Zone,
Minhang District, Shanghai, China.
+86-21-5442-1616
+86-21-5442-0099
http://www.asus.com.cn
Technical Support
Telephone Online Support
A-2
+86-21-3407-4610 (800-820-6655)
http://support.asus.com/techserv/techserv.aspx
Appendix
ASUS contact information
ASUS COMPUTER INTERNATIONAL (America)
Address
Fax
Web site
800 Corporate Way, Fremont, CA 94539, USA
+1-510-608-4555
http://usa.asus.com
Technical Support
Support fax
General support
Online support
+1-812-284-0883
+1-812-282-2787
http://support.asus.com/techserv/techserv.aspx
ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Web site
Online contact
Harkort Str. 21-23, D-40880 Ratingen, Germany
+49-2102-959911
http://www.asus.de
http://www.asus.de/sales
Technical Support
Telephone Support Fax Online support +49-1805-010923
+49-2102-959911
http://support.asus.com/techserv/techserv.aspx
ASUS Czech Service s.r.o. (Europe)
Address Telephone Web site Na Rovince 887, 720 00 Ostrava – Hrabová, Czech
Republic
+420-596766888
http://www.asus.cz
Technical Support
Telephone Fax E-mail Online Support +420-596-766-891
+420-596-766-329
advance.rma.eu@asus.com
http://support.asus.com/techserv/techserv.aspx
ASUS RS520-E8-RS8 V2, RS520-E8-RS12-EV2
A-3
ASUS contact information
ASUS Holland BV (The Netherlands)
Address Web site
Marconistraat 2, 7825GD EMMEN, The Netherlands
http://www.asus.com
Technical Support
Telephone Fax E-mail Online Support +31-(0)591-5-70292
+31-(0)591-666853
advance.rma.eu@asus.com
http://support.asus.com/techserv/techserv.aspx
ASUS Polska Sp. z o.o. (Poland)
Address Web site Ul. Postępu 6, 02-676 Warszawa, Poland
http://pl.asus.com
Technical Support
Telephone Online Support +48-225718033
http://support.asus.com/techserv/techserv.aspx
ASK-Service (Russia and CIS)
Address Telephone Web site г.Москва, ул. Орджоникидзе, д.10, Россия
(495) 640-32-75
http://ru.asus.com
Technical Support
Telephone Online Support A-4
008-800-100-ASUS (008-800-100-2787)
http://vip.asus.com/eservice/techserv.aspx?SLanguage=ru
Appendix
Download PDF