OWNER’S
MANUAL
RP11128-350-OP
Rev. 0911
Stand-up Fastener Installation Tools
153 BOWLES ROAD, AGAWAM, MA 01001 USA
800.633.3800 | WWW.OLYFAST.COM
UÊ IMPORTANT!
Save this manual
and read it in full
before use.
TA BL E OF C ONTE NTS
2 Safety Instructions
3 Wire Gauge
3 Operating Instructions
General
Loading Plates
Operating the Tool
Depth Adjustment
4 Parts Removal and Replacement
Feed Tube Removal and Replacement
Screw Gun Removal and Replacement
Drive Shaft, Hex Pin Insert and Bit(s)
Ejector Blade Insert Discs
Clearing Fastener and Plate Jams
Cleaning Procedure
5 Troubleshooting Problems
6 Warranty and Remedy
7 Parts List
11 Cleaning and Maintenance Procedures
Necessary Supplies
Dismantling the Tool
NO T I C E
The AccuTrac tool is used throughout this manual as the example for
processes and instructions. Since
the three tools are similar, the
methods given also correspond to
the AccuSeam and RhinoTrac tools,
except where noted.
If you have any questions or concerns about
any of the material covered in this booklet,
please contact your local OMG representative or call OMG Roofing Products
Technical Services Department at
1.800.633.3800.
WARNING
When using electric tools, safety precautions should always be followed to
reduce the risk of fire, electric shock, and personal injury. Failure to follow
these instructions can result in severe personal injury.
R E AD & SAVE ALL I NSTRUCTI ONS
GENERAL SAFETY
CONSIDERATIONS
4. Don’t abuse the tool:
1. Before using the tool, become familiar with all
of the operating instructions.
2. Don’t use the tool for purposes not intended.
3. Failure to wear safety glasses with side
shields can result in severe eye injury or
blindness. Always wear safety glasses
with side shields that conform to ANSI
Standard Z87.1.
UÊ Keep handle dry, clean and free from oil
and grease.
UÊ Never carry the tool by the cord or yank it
to disconnect from the receptacle.
UÊ Always keep the cord from heat, oil and
sharp edges.
UÊ Always store an idle tool in a dry, high or
locked-up place.
UÊ Always disconnect the tool when it’s not in
use or before servicing.
4. Keep the work area clean and well lit.
Dark, cluttered work areas and benches
invite injuries.
5. Dress properly! Never operate the tool while
wearing loose clothing or jewelry. They can be
caught in moving parts.
6. Maintain proper footing and balance at
all times:
UÊ Don’t use the tool in an awkward position.
UÊ Don’t overreach.
7. Stay alert! Watch what you are doing! Use
common sense! Do not operate tool when you
are tired!
SAFETY PROCEDURES
FOR ELECTRIC TOOLS
1. Guard against electric shock.
2. Consider work area environment:
UÊ Never operate tool in damp or wet
locations.
UÊ To avoid unintentional starting, never
carry a plugged-in tool with finger on the
switch. Be sure the switch is OFF when
plugging in.
5. Maintain the tool with care. Check damaged
parts. Before further use of the tool, a guard
or other part that is damaged should be
carefully checked to determine that it will
operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part
that is damaged should be properly repaired
or replaced by an authorized service center
unless otherwise indicated elsewhere in this
instruction manual. Have inoperative switches
replaced by an authorized service center. Do
not use the tool if the switch does not turn the
tool ON and OFF.
UÊ When servicing double insulated tool, use
identical replacement parts.
UÊ Prevent body contact with grounded
surfaces, such as pipes.
UÊ Keep the tool clean for better and safer
performance.
UÊ Use only extension cords intended for
outdoor use and so marked.
UÊ Wear rubber gloves and non-skid footwear
when working outdoors.
UÊ Don’t expose power tools to rain.
UÊ Inspect the tool cord periodically and,
if damaged, have it repaired by an
authorized service facility.
UÊ Inspect the extension cord periodically and
replace it if it’s damaged.
UÊ Never operate tool in the presence of
flammable liquids or gases.
3. Never allow visitors to contact the tool or
extension cords. All visitors should be kept
away from the work area.
AccuTrac®, RhinoBond® and EyeHook® are registered trademarks of OMG, Inc.
© Copyright 2011 OMG, Inc. All rights reserved.
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 2
OP E RATI NG I NSTRUCTI ONS
IMP ORTANT NOTE
BEFORE USING TOOL
Extension cords must be of adequate wire size
(AWG or American Wire Gauge) for safety, to
prevent loss of power and to avoid overheating. To determine the minimum wire size
required, refer to the following chart:
Cord Length
25' 50' 75' 100' 125' 150'
(Feet)
Wire Size
(Gauge)
18
16
14
14
12
12
NOTICE
OMG Roofing Products is not responsible for
damage to the tool and/or improper installation
as a result of using fasteners and/or plates
other than described here.
The AccuTrac tool was designed for use with 3"
square plates (insulation) and approved fasteners manufactured by OMG Roofing Products.
The AccuSeam tool was designed for use
with 23⁄8" EyeHook® plates (membrane)
and approved fasteners manufactured by
OMG Roofing Products.
The RhinoTrac tool was designed for use with
3" specially coated RhinoBond® plates
and approved fasteners manufactured
by OMG Roofing Products.
GENERAL
1. Use only with approved plates and
fasteners manufactured by OMG Roofing
Products. See notice at left.
2. At the beginning of each day, wipe down the
tubes and the bottom of the ejector plate.
Lubricate the linkage and the plate ejector
blade, if needed, then unlatch the tool.
5. Check the plate to make sure it is properly
seated and adjust fastener depth if necessary.
6. Roll the tool to the next plate application
position on the roof and repeat the “tool use”
instructions.
DEPTH ADJUSTMENT
3. Load the plate hold with the proper plates.
4. Make sure the screw gun is in the FORWARD
mode. Connect the tool to the proper power
source.
5. At the end of the day, remove any dust
accumulation from the tubes and the bottom of
the ejector blade.
6. Lubricate all moving parts. Excess lubricant will
evaporate overnight.
7. Relatch the tool and store it in its case.
LOADING PLATES
Overdriving can cause the screw to strip out the
metal deck and not hold. The tool should be adjusted to make the plate snug so that it does not
spin freely on the surface. The plate should not be
so tight as to cause it to deform.
To avoid overdriving, it is suggested that the operator deliberately start with the adjustment set
too loose and then slowly make adjustments until
the desired tightness is reached.
Adjustments are made using the large ring located
on the upper body tube of the tool. Moving the
ring upwards towards the screw gun will
make the screw deeper (tighter).
NOTE: If you are unable to make the plate “snug”
through adjusting the depth adjustment nut, make
sure that the screw gun is in the forward position
(not reverse).
1. Push and turn the plate retaining handle
counterclockwise and lift the retaining rod to
its extended position.
2. Remove the pre-packaged plates from the box.
For AccuTrac, align the notch in the plates
with the projection on the back side of the
plate hold. For AccuSeam, make sure the
EyeHooks are facing down.
3. Drop the plates into the hold, slide the
retaining rod down, then push and turn it
clockwise to lock the handle in position.
Depth Variation
Adjustment Nut
OPERATING THE TOOL
1. Drop one screw, point down, into the funnel.
2. Fully compress the tool to allow a plate to be
ejected from the stack and moved into position
for attaching to the insulation or membrane.
At this point the screw will be released and
will drop down the feed tube. Allow the tool to
fully extend, then drop another screw into the
funnel. It will be contained at the mouth of the
funnel until needed.
3. Lock the screw gun trigger in the ON position.
Using the lock will keep the screw gun running
cooler. Push the tool downward to drive the
screw through the insulation or membrane until
it contacts the deck. Continue to hold down on
the tool until the plate is fully seated.
4. Allow the tool to retract to its original position.
This motion causes the next plate to be ejected
from the stack and the second screw to drop
down the feed tube.
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 3
Looser
Tighter
PAR T S R E M O VAL AND R E P L AC EMENT
Always use OMG Roofing Products replacement parts.
SCREW GUN REMOVAL
AND REPLACEMENT
5. Reinstall the drive shaft assembly into the
screw gun making sure it snaps into place.
FEED TUBE REMOVAL
AND REPLACEMENT
1. Loosen the star knob assembly on the screw
gun motor clamp and rotate the screw gun
in the counterclockwise direction until the
threads disengage.
6. Lower the drive shaft/screw gun assembly into
the tool and rotate the screw gun clockwise
until tight.
1. Disconnect the upper link from the feed tube
assembly by sliding the metal bushings inward
and push the upper link forward to disengage.
Repeat the process for the opposite upper link.
2. The tool can now be removed from the base by
pulling up on the tool.
3. Once the tool is separated from the base, you
can remove the feed tube from the upper tube
by pulling on the spring-loaded retention pin
and separating it from the bracket on the upper
tube. The feed tube should now release from
the tool.
4. To reinstall the feed tube, align the lower end
so that the “ears” engage the notches of the
lower tube.
5. Angle the feed tube towards the upper tube
and reinstall the retention pin into the bracket.
6. Reattach the upper links by sliding the metal
bushings inward and connecting the links.
WARNING
The nosepiece is not to be removed!
1. The nosepiece is under spring-loaded
pressure. Attempting to remove the
nosepiece could cause personal injury.
2. See warning sticker on tool!
3. Contact 1.800.633.3800 to locate your
nearest authorized OMG Roofing
Products AccuTrac Distributor and
Service Center.
7. Rotate the screw gun to properly align for
operation. When set, securely tighten the star
knob on the motor clamp assembly. Do not
overtighten the screw gun.
2. The screw gun must be raised straight up to
allow the screw gun and the attached drive
shaft to be removed from the tool.
3. When the assembly is free, pull the drive shaft
from the screw gun. To reattach the screw gun,
reverse the above process. Be careful not to
over-tighten the screw gun as this may cause
the nosepiece of the screw gun to fall off.
DRIVE SHAFT, HEX PIN
INSERT AND BIT(S)
NOTE: This step does not apply to RhinoTrac.
1. If the ejector blade insert or discs are worn
and need to be replaced, the ejector blade
assembly must first be removed from the tool.
2. Remove the two socket head cap screws
that connect the ejector blade to the drive
bar. Withdraw the ejector blade and take the
assembly to a clean working surface.
1. Remove the screw gun and drive shaft
assembly as described above. Separate the
screw gun from the drive shaft by simply
pulling on the shaft from the screw gun.
2. Carefully inspect the drive shaft, spring pin
hex insert, Phillips cap and bit assemblies for
excessive wear, cracks and/or damage of any
kind. If either the shaft, spring pin hex insert,
Phillips cap or bits require replacing, use
assembly part number 6634910 (Universal drive
shaft), 6606910 (spring pin hex insert), 6722910
(1.4" length reversible hex bit), 6637910
(Phillips cap) and 6624910 (Phillips bit insert).
3. If only the drive bit needs
to be replaced, first locate
where the spring pin insert
holds the bit cap, then
press in on the spring pin
to affect release.
3. The ejector blade insert or discs are fastened
to the blade with two socket head cap screws.
The screws are secured with a retaining
compound and they must be heated before
they can be removed. This is best done if
heat is applied with a small propane torch.
CAUTION
Use care to avoid personal injury
or heat damage to surroundings.
4. Remove the two screws and the two inserts or
discs and replace with new discs.
4. When replacing a Phillips
bit, insert a new bit into the Phillips cap then
fit it over the end of the drive shaft, press in
on the spring pin while aligning the hole in the
cap or bit and push in until the spring pin snaps
into place. For Hex Head users: To reinstall
the hex drive, simply fit it over the end of the
drive shaft, press in on the spring pin while
aligning the hole in the hex drive and push in
until the spring snaps into place.
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
EJECTOR BLADE INSERT OR DISCS
Page 4
5. Coat the thread of the screws with
retaining compound and securely tighten
them. Allow 24 hours for the compound
to cure.
6. Insert the ejector blade into the tool, align
it with the drive blade, insert and securely
tighten the two socket head cap screws to
fasten the ejector blade to the drive blade.
CLEARING FASTENER
AND PLATE JAMS
1. Remove the feed tube (follow directions
as described on page 4 of this manual) to
access the junction where most fastener
jams occur. You should be able to clear the
fastener(s) from the nosepiece.
2. In some cases it may be necessary
to remove the jaws in the end of the
nosepiece to fully access the jam. The jaws
can be removed by removing the O-ring that
holds them in the nosepiece.
3. For clearing plate jams, first make sure
the tool is completely retracted in its full
upright position. This may require that you
tug upwards on the tool. Most likely, a
plate will shuttle into the proper place.
4. If the plate remains jammed, remove
the stack of plates from the holder. First,
attempt to cycle the ejector blade by
quickly compressing the tool downward.
The jammed plate should dislodge. If it
does not, you will need to remove the
plate manually as it is most likely stuck
underneath the gate. This may require a
pair of pliers. Take care not to damage the
ejector blade or gate mechanism.
5. Once the jammed plate is removed,
reinstall the plates in the plate hold.
CLEANING PROCEDURE
1. The linkages, ejector blade and housing
should be cleaned weekly with a
commercial solvent.
2. Special attention should be paid to the
linkage connections and the groove in the
casting (black base) that holds the ejector
blade. Be sure these grooves are free of
burrs, asphalt and dirt.
3. Once clean, relubricate the ejector blade
track with Tri-Flow or a Teflon-based
lubricant.
4. The gate should also be checked
periodically to ensure it is not sticking. If it
is, clean with a degreaser and relubricate.
T R OUBLESHOOTI NG PROBLEMS
PROBLEM: PLATES NOT FEEDING SMOOTHLY OR COMPLETELY
POTENTIAL CAUSE
REMEDY
Plates have been inserted
upside down.
Remove plates from plate hold and reinstall so the notch in the plate
fits the extrusion in the plate hold.
Last plate in the hold jams in
the gate.
It is recommended that the plate hold be refilled when approximately
10 plates are left.
Dirty ejector blade and/or
guides.
Clean the ejector blade and/or guides with degreaser.
Gate is sticking.
Clean the gate with a degreaser.
Ejector blade screws are
loose.
Remove the screws, clean the screws and threaded holes.
Apply Loctite 242 and reinstall screws.
Ejector blade insert screws
are loose.
Remove the screws, clean the screws and threaded holes.
Apply Loctite 242 and reinstall screws.
Ejector blade insert undercut
is clogged.
Clean out the undercut.
Nosepiece is bent.
Call 1.800.633.3800 for service. Do not attempt to remove nosepiece.
Plate stop screws are loose.
Remove the screws, clean the screws and threaded holes.
Apply Loctite 242 and reinstall screws.
Plate retaining spring is not
completely seated.
Turn the handle clockwise and gently pull upward. (Note: Does not
apply to AccuSeam.)
Plate rod is not completely
seated.
Turn the handle clockwise and gently pull upward. (Note: Does not
apply to AccuSeam.)
PROBLEM: MISSING OR SKIPPED PLATES
Plate is bent or previously
used.
Disconnect upper links from the feed tube and slide ejector blade forward. Remove suspect plate(s). Reconnect upper links and continue.
Ejector blade insert disc(s)
is/are missing.
Replace missing insert.
Incorrect plates are being
used.
Use only OMG Roofing Products AccuTrac plates.
Ejector blade insert disc
undercuts are dirty/clogged.
Clean out undercuts.
PROBLEM: SCREWS NOT FEEDING OR INSTALLING PROPERLY
Wrong bit installed.
Use only AccuTrac drive bits. #3 Phillips drive bit 6624910 or
1.4" reversible hex bit 6722910.
Obstructed feed tube.
Clean or replace the feed tube.
Two screws jammed in feed
tube or nosepiece.
Remove feed tube and dislodge screws.
Screws are too long.
Screws must not exceed 6" in length.
Nosepiece jaws are installed
upside down.
Jaws must be installed with beveled edge facing upward.
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 5
POTENTIAL CAUSE
WARRANTY AND REMEDY
REMEDY
Drive shaft is broken.
Replace drive shaft.
Anti-jam mechanism is dirty
or stuck.
Clean anti-jam mechanism. Check to see if springs are activating
properly. Replace if needed.
ALL WARRANTIES OF THE PRODUCTS
DESCRIBED HEREIN, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSES ARE SPECIFICALLY
EXCLUDED, EXCEPT FOR THE FOLLOWING:
OMG Roofing Products will repair or replace,
at its sole option, any tool part which within
90 days after sale by OMG Roofing Products
or its distributors, is found by OMG Roofing
Products to be defective in material or workmanship, normal wear and tear excluded.
PROBLEM: PLATE NOT SEATING TIGHTLY
Improper depth adjustment.
Tighten the depth adjustment.
Screw gun is in reverse.
Make sure switch is in forward position.
Incorrect drive bit, or worn/
broken bit.
Check to make sure correct drive bit is installed. Replace worn or
broken drive bits.
Nosepiece jaws are installed
upside down.
Jaws must be installed with beveled edge facing upward.
Screw gun not properly
installed or fully tightened.
Check screw gun; tighten if necessary.
THIS IS THE SOLE WARRANTY OF OMG
ROOFING PRODUCTS AND THE SOLE
REMEDY AVAILABLE TO DISTRIBUTOR
OR BUYER.
Excessive build-up of material Remove built-up material.
on wheels/casting.
Obstruction in tubes and/or
casting.
Check upper and lower tubes and casting, remove any
obstructions.
PROBLEM: TOOL WILL NOT RETRACT INTO FULL UPWARD POSITION
Operator is not allowing tool
to fully retract.
Downward pressure on tool must be fully released after the plate has
been fastened. Tool should “spring” up into correct position.
If necessary, tug upwards.
Ejector blade or tubes are
dirty.
Clean and oil ejector blade and tubes.
Nosepiece is bent or damaged. Call 1.800.633.3800 for service. Do not attempt to remove nosepiece.
Fastener wedged between
feed tube and nosepiece.
Remove feed tube and clear fastener jam.
PROBLEM: TOOL IS SLUGGISH
Ejector blade needs
lubricating.
Lubricate the ejector blade.
Dirty upper and lower tubes,
Remove debris. Clean all parts with a degreaser and lubricate.
ejector blade, guides and drive
bar slots.
Upper and/or lower tubes are
bent or damaged.
Replace worn or damaged tubes as needed.
Nosepiece retaining screw
is worn or the nosepiece is
damaged.
Call 1.800.633.3800 for service. Do not attempt to remove
nosepiece.
If you have followed the recommendations above, but your problems persist, please call the
OMG Roofing Products Technical Services Department at 1.800.633.3800.
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 6
PA R T S B R E A KDOWN –
U P P E R A S S E MBLY
Common for All Tools
A(3)
A(4)
A(1)
1
7A
A(5)
3
A(2)
7
KEY DESCRIPTION
1
2
3
4
5
6
7
7A
8
9A
9B
PART #
Screw Gun, DeWalt, DW284 . . . . . . . . . . . . . . .6319910
Upper Spring . . . . . . . . . . . . . . . . . . . . . . . . . . .6291910
Upper Tube Body . . . . . . . . . . . . . . . . . . . . . . . .6641910
Depth of Drive Adjustment Knob . . . . . . . . . . . .6288910
Feed Tube Mounting Assembly . . . . . . . . . . . . .6649910
Lower Tube Body (exterior) . . . . . . . . . . . . . . . .6650910
Lower Spring . . . . . . . . . . . . . . . . . . . . . . . . . . .6299910
Spring Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . .6635010
Nosepiece (not removable
from lower tube body) . . . . . . . . . . . . . . . . . . . .6629910
Nosepiece Jaws . . . . . . . . . . . . . . . . . . . . . . . .6284910
O-Ring for Jaws . . . . . . . . . . . . . . . . . . . . . . . . .6285910
4
B
5
Assemblies
A
B
Screw Gun Mounting Clamp Assembly
A(1) Upper Mount w/Screws . . . . . . . . . . . . . .6377910
A(2) Nutless Mounting Collar . . . . . . . . . . . . . .6639910
A(3) Star Knob . . . . . . . . . . . . . . . . . . . . . . . . .6787910
A(4) Latch Cable . . . . . . . . . . . . . . . . . . . . . . . .6671910
A(5) Bullet with Set Screw . . . . . . . . . . . . . . . .6788010
Universal Drive Shaft Assembly . . . . . . . . . . . .6634910
Includes Drive Shaft B(1), Spring
Pin Hex Insert B(2), #3 Phillips Insert
Bit and Phillips Cap
B(1) Spring Pin Hex Insert . . . . . . . . . . . . . . . . .6606910
B(2) #3 Phillips Insert Bit. . . . . . . . . . . . . . . . . .6624910
B(3) Phillips Cap . . . . . . . . . . . . . . . . . . . . . . . .6637910
1.4" Length Reversible Hex Bit . . . . . . . . . . . . .6722910
#3 Square Drive Bit . . . . . . . . . . . . . . . . . . . . . .6693910
B(1)
9B
B(2)
6
B(3)
8
2
9A
WARNING
All parts must be inspected periodically
and replaced if worn or broken.
Failure to do this can affect a
product’s operation and cause
personal injury.
9A
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 7
PAR T S B R E A K D OW N – L OW E R ASSEMBLY
C(1)
C(4)
C(2)
C(3)
13
E(1)
C(5)
E(3)
D(2)
D(5)
E(3)
D(1)
D(4)
E(2)
10
D(3)
14
E(2)
12
E(1)
11
14
KEY DESCRIPTION
10
11
12
13
14
NA
PART #
Base Casting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . —
Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8310020
Plate Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6639920
Flexible Plate Alignment Shaft . . . . . . . . . . . . .6724910
Rear Wheels with Axle . . . . . . . . . . . . . . . . . . .6701910
AccuTrac Case (not shown) . . . . . . . . . . . . . . . .6631910
Complete Tool with Case . . . . . . . . . . . 6626910
KEY DESCRIPTION
PART #
KEY DESCRIPTION
Assemblies
C
D
Dual Lever Anti-Jam Feed Tube Assembly . . . .6791910
C(1) Upper Anti-Jam Lever & Spring . . . . . . . .6784910
C(2) Lower Anti-Jam Lever & Spring . . . . . . . .6785910
C(3) Pull Pin & Spring (attaches Feed Tube
to Upper Tube Body) . . . . . . . . . . . . . . . . .6786910
C(4) Lever Actuator Rod . . . . . . . . . . . . . . . . . .6788910
C(5) Actuator Nub . . . . . . . . . . . . . . . . . . . . . . .6790910
Ejector Blade Assembly, 3" Square . . . . . . . . . .6653910
D(1) Ejector Blade Plate . . . . . . . . . . . . . . . . . .6675910
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 8
E
PART #
D(2) Ejector Blade Insert . . . . . . . . . . . . . . . . .6640910
D(3) Ejector Blade Drive Bar . . . . . . . . . . . . . . .6632910
D(4) Drive Bar Retaining Screws . . . . . . . . . . .6645910
D(5) Socket Head Cap Screw, ¼"-28 x ¾" . . . . .6643910
Quick Release Linkage Assembly . . . . . . . . . . .6700910
E(1) Upper Links. . . . . . . . . . . . . . . . . . . . . . . . . . . . . —
E(2) Lower Linkage Bars . . . . . . . . . . . . . . . . . . . . . . —
E(3) Sliding Bushings & Springs . . . . . . . . . . . . . . . . —
UÊ Õň˜}à . . . . . . . . . . . . . . . . . . . . . . . .6691910
UÊ -«Àˆ˜}à . . . . . . . . . . . . . . . . . . . . . . . . .6692910
PAR T S B R E A K D OW N – L OW E R ASSEMBLY
C(1)
C(4)
C(2)
16
C(3)
E(1)
13
D(1)
C(5)
E(3)
D(2)
E(3)
D(4)
E(2)
10
D(3)
14
E(2)
12
E(1)
15
11
14
KEY DESCRIPTION
10
11
12
13
14
15
16
NA
PART #
Base Casting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . —
Gate with Plate Hold Mechanism . . . . . . . . . . .8320020
Plate Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6639930
Plate Hold Rods & Assembly . . . . . . . . . . . . . . . . . . . —
Removable Rear Wheels with Axle . . . . . . . . . .6702910
Measuring Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . —
Front Wheel with Axle and Bracket
AccuSeam Case (not shown) . . . . . . . . . . . . . . .6901910
Complete Tool with Case . . . . . . . . . . . 6908910
KEY DESCRIPTION
PART #
KEY DESCRIPTION
Assemblies
C
D
Dual Lever Anti-Jam Feed Tube Assembly . . . .6791910
C(1) Upper Anti-Jam Lever & Spring . . . . . . . .6784910
C(2) Lower Anti-Jam Lever & Spring . . . . . . . .6785910
C(3) Pull Pin & Spring
(attaches feed tube to upper tube body) . .6786910
C(4) Lever Actuator Rod . . . . . . . . . . . . . . . . . .6788910
C(5) Actuator Nub . . . . . . . . . . . . . . . . . . . . . . .6790910
Ejector Blade Assembly, 23⁄8" Round . . . . . . . . . . . . . —
D(1) Ejector Blade Plate . . . . . . . . . . . . . . . . . .6900910
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 9
E
PART #
D(2) Ejector Blade Insert Discs . . . . . . . . . . . . . . . . —
D(3) Ejector Blade Drive Bar . . . . . . . . . . . . . . . . . . . —
D(4) Drive Bar Retaining Screws . . . . . . . . . . . . . . . —
Quick Release Linkage Assembly . . . . . . . . . . .6700910
E(1) Upper Links. . . . . . . . . . . . . . . . . . . . . . . . . . . . . —
E(2) Lower Linkage Bars . . . . . . . . . . . . . . . . . . . . . . —
E(3) Sliding Bushings & Springs . . . . . . . . . . . . . . . . —
UÊ Õň˜}à . . . . . . . . . . . . . . . . . . . . . . . .6691910
UÊ -«Àˆ˜}à . . . . . . . . . . . . . . . . . . . . . . . . .6692910
PAR T S B R E A K D OW N – L OW E R ASSEMBLY
C(1)
C(4)
C(2)
C(3)
13
E(1)
C(5)
E(3)
D(5)
E(3)
D(1)
E(2)
10
D(3)
14
E(2)
12
E(1)
11
14
KEY DESCRIPTION
10
11A
11B
12
13
14
NA
PART #
Base Casting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . —
Left Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .833001
Right Gate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .833002
Plate Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6639940
Flexible Plate Alignment Shaft . . . . . . . . . . . . .6726910
Rear Wheels with Axle . . . . . . . . . . . . . . . . . . .6703910
RhinoTrac Case (not shown) . . . . . . . . . . . . . . .6631910
KEY DESCRIPTION
PART #
KEY DESCRIPTION
D
Assemblies
C
Dual Lever Anti-Jam Feed Tube Assembly . . . .6791910
C(1) Upper Anti-Jam Lever & Spring . . . . . . . .6784910
C(2) Lower Anti-Jam Lever & Spring . . . . . . . .6785910
C(3) Pull Pin & Spring (attaches Feed Tube
to Upper Tube Body) . . . . . . . . . . . . . . . . .6786910
C(4) Lever Actuator Rod . . . . . . . . . . . . . . . . . .6788910
C(5) Actuator Nub . . . . . . . . . . . . . . . . . . . . . . .6790910
Complete Tool with Case . . . . . . . . . . . RTTOOL
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 10
E
PART #
Ejector Blade Assembly, 3" Round. . . . . . . . . . .6653910
D(1) Ejector Blade Plate . . . . . . . . . . . . . . . . . .6675910
D(3) Ejector Blade Drive Bar . . . . . . . . . . . . . . .6632910
D(5) Socket Head Cap Screw, ¼"-28 x ¾" . . . . .6643910
Quick Release Linkage Assembly . . . . . . . . . . .6700910
E(1) Upper Links. . . . . . . . . . . . . . . . . . . . . . . . . . . . . —
E(2) Lower Linkage Bars . . . . . . . . . . . . . . . . . . . . . . —
E(3) Sliding Bushings & Springs . . . . . . . . . . . . . . . . —
UÊ Õň˜}à . . . . . . . . . . . . . . . . . . . . . . . .6691910
UÊ -«Àˆ˜}à . . . . . . . . . . . . . . . . . . . . . . . . .6692910
C L EA N I N G A N D M A INT E NANC E PROCEDURES
This procedure is a simple and effective way to
clean your tool to maintain reliable operation.
Regular cleaning and lubrication will also extend
part life and ensure smooth operation.
DISMANTLING THE TOOL FOR ROUTINE MAINTENANCE
NOTE: The illustrations show the AccuTrac tool,
but the procedure is the same for AccuSeam and
RhinoTrac.
NECESSARY SUPPLIES
Wire Brush
Aerosol
“Safety Solvent”
Cloth Rag
Putty Knife
1. Disconnect the upper link from the feed tube
assembly by sliding the metal bushings inward
and push the upper link forward to disengage.
Repeat the process for the opposite upper link.
The tool can now be removed from the base by
pulling up on the tool.
3. Wipe nosepiece with clean cloth.
Allen wrenches
(3⁄8" and 3⁄16")
4. Wipe lower tube with clean cloth.
Teflon-based
lubricating oil,
i.e., Tri-Flow™
Loctite® Removable
Threadlocker
(Blue Loctite)
2. Once the tool is separated from the base you
can remove the feed tube from the upper tube
by pulling on the spring-loaded retention pin
and separating it from the bracket on the upper
tube. The feed tube should now release from
the tool.
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 11
CAUTION
Feed tube must be properly hooked on
lower tube casing to ensure proper tool
operation. Incorrect assembly will
lead to fastener misfeeds or
overdriven fasteners.
6. Prior to reassembling the tool, lubricate the
linkage and ejector blade track using a
Teflon-based lubricant, i.e., Tri-Flow™ making
sure to wipe excess lubricant from tool.
8. Use Allen wrenches and (Blue) Loctite® to
ensure that linkage screws are tightened
securely.
5. Inspect the wheeled-base assembly for build-up
of asphalt, adhesives or debris. Spray with
safety solvent and remove foreign material from
the linkage and track ejector blade. If your tool
has been used for extended periods of operation
or under extremely dirty operating conditions,
it may be necessary to soak the wheeled-base
assembly in a pan of safety solvent or parts
cleaning tank.
7. Reassemble the tool by reversing disassembly
procedures on previous page.
OMG ROOFING PRODUCTS
153 BOWLES RD., AGAWAM, MA 01001 USA
800 . 633 . 3800 | WWW.OLYFAST.COM
AccuTrac / AccuSeam / RhinoTrac Owner’s Manual
Page 12