U4 DBT - Canohm

U4 DBT
GB
Version 1
The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by
SANGEAN ELECTRONICS INC. is under license.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
GB
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet. Consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they
exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged. liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. To Reduce the Risk of Fire or Electric Shock, Do not Expose
This Appliance To Rain or Moisture.
16. The Shock Hazard Marking and Associated Graphical Symbol
is provided on the rear of unit.
17. Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, shall be placed on the apparatus.
18. Excessive sound pressure on ear- and headphones could impair
the hearing ability. Higher setting that idle on the equalizer
leads to higher signal voltages on the output for ear and headphones.
19. The power plug should be close to the radio, and easy to be
approached that during the emergency, to disconnect the power
from the radio, just unplug the power plug from the AC power
slot.
20. Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnected device shall remain readily
operable.
21. The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
22. This apparatus is provided with protection against splashing
water and dust ingress (IP64).
CAUTION: These servicing instructions are for use by qualified
service personnel only. To reduce the risk of the electric shock, do
not perform any servicing other than that contained in the operating
instructions unless you are qualified to so.
GB
Control
1
2
3
4
5
6
7
8
9
10
11
Battery locker
NFC detection tag
Display protection bar
Preset button (Preset 3: rewind
button/Preset 4: Play/Pause/
Preset 5: Fast-forward button)
Alarm 1 button
Volume control/Tone control
Alarm 2 button
Auto tune button/Bluetooth
pair button
LCD display
Info button
Menu button
Bluetooth status indicator
Charging/Low battery indicator
14 Tuning control/Select
15 Source button
16 Power button
17 Speaker
18 Auxiliary input socket
19 DC in socket
20 USB charging socket
21 Battery compartment
22 Rod antenna
23 Socket for software upgrade
24 NiMH/Alkaline batteries switch
12
13
GB
LCD Display
A
B
C
D
E
Sleep indicator
Volume indicator
AM/PM time indicator
Clock digits
FM mode indicator
F
G
H
I
J
DAB mode indicator
Aux in indicator
Two line text display
Alarm 1 and 2 indicator
Snooze indicator
Power the radio
1. Battery operation
Note: No batteries are included with this radio.
Pull out the battery compartment locker to release battery com
partment. Insert 6 x D size (UM-1) battery into the compartment.
Ensure the battery is inserted in accordance with the diagram shown.
Return the battery locker to the original position. If the radio is not
to be used for any extended period of time, it is recommended that
the battery is removed from the radio.
GB
Battery operation using alkaline batteries
1. Before you insert the batteries, if you use non-rechargeable
batteries, make sure the NiMH/Alkaline switch which located
inside the battery compartment is switched to Alkaline position.
If you use rechargeable batteries, make sure to switch NiMH/
Alkaline switch to NiMH position.
2. Reduced power, distortion and a “stuttering sound” are all signs
that the batteries need replacing.
Battery operation using rechargeable batteries
1. Slide the battery switch to the NiHM position.
2. Insert 6 UM-1 batteries into spaces in the compartment. Make
sure all batteries are inserted with the correct polarity as shown
on the rear cabinet. The radio is also designed to be used with
NiMH rechargeable batteries.
Note:
Do not use a mix of old and new rechargeable batteries.
Do not use a mix of full and empty rechargeable batteries.
Do not use batteries that have a different mAh capacity
Do not use damaged or leaking batteries
3. Make sure the radio is switched off and connected to the
AC mains socket. When the charge indicator flashes yellow
indicating batteries are charging. Batteries will be fully charged
in around 10 hours. The battery shows steady yellow light when
the battery charging is complete.
Note:
Duration for charging your battery fully can be varied according
to the mAh capacity of a battery. Higher mAh batteries required
longer charging time.
GB
Important:
Under some conditions the charging LED indicator may switch
off after flashing briefly. This may happen if the batteries are
already freshly charged, or if the radio detects that you may be
attempting to recharge alkaline batteries or mixed different types
or capacity of rechargeable battery. In these cases the charging
will be stopped.
2. AC operation
Before you plug the AC cord into the AC socket, be sure the
voltage is correct. If you have batteries in the radio and use the
AC power cord, the batteries will automatically be disconnected.
AC cable hook is designed to store the cord when the radio is
not in use.
Important:
The mains plug is used as the means of connecting the radio
to the mains supply. The mains socket used for the radio must
remain accessible during normal use. In order to disconnect
the radio from the mains completely, the mains plug should be
removed from the mains outlet completely.
3. Powered via DC IN socket
The radio can be also powered via the DC IN socket which
can allow 12 Volt DC, which is designed to be powered by the
vehicle or the boat so you can take the radio with you outdoors
or on the boat.
An additional cigarette lighter cable is required (not supplied) for
this device.
Note: Never use the 12 Volt socket in rainy or moist conditions
to prevent moist from entering the radio. Always keep the rubber
cover on the back well closed under these conditions.
10
Battery charging status indicator
Please note that the battery charging status detection can only
be activated when the radio is in charging mode (i.e. the radio is
switched off, the battery switch slides to the NiHM position and it is
connected to the AC mains socket).
When charging is in progress, display is shown at right and the charging
indicator flashes yellow.
When the charging process is completed, display is shown at right and the
charging indicator lights in steady yellow.
If batteries are already fully charged,
display is shown at right and it will
switch to standby mode after 5 seconds.
When there is no battery/missing batteries in the compartment or some of
batteries are inserted with the incorrect polarity, display is shown at right
and it will enter standby screen after 5
seconds.
Note: If a battery is removed while
charging, display is shown at right and
the charging indicator lights red.
11
GB
During the charging process, if a battery is detected as faulty/damaged,
a solid square will be displayed under
the corresponding battery number (see
picture, right) and the charging indicator flashes red.
12
Using DAB for the first time- DAB
1. Straighten up the antenna.
2. Press the Power button to switch on the radio. If the radio has
been used before the last used mode will be selected.
3. Press and release the Source button to select DAB mode. The
display will show DAB for a few seconds.
4. If this is the first time the radio is used a quick scan of the DAB
Band III channels may be carried out. The display will show
‘Scanning’ (If the radio has been used before the last used
station will be selected instead.)
During the scanning process, as new stations are detected the
station counter will increase and the stations will be added to
the list which is stored in the radio. The bar graph indicates the
progress of the scan.
5. When scanning is completed the radio will list the stations found
(in numeric-alpha order 0....9...A...Z), unless it has previously
been tuned to a DAB station.
Rotate the Tuning control to scroll through the list of available
DAB radio stations.
Press the Tuning control to select the highlighted station. The
display may show 'Connecting...' while the radio re-tunes.
When a DAB station is found, the display will show the station
name on the upper line of the text display and broadcast
information on the lower line.
Use the Volume control to set the sound level as needed.
6. If the station list is still empty after the scan the display will show
‘No DAB Station” then return to the DAB menu. If no stations are
found it may be necessary to relocate your radio to a position
giving better reception.
13
Selecting a station- DAB
1. When playing a DAB radio station, the display normally shows
the name of the current station with other related information.
GB
2. Rotate the Tuning control to access the radio station list and to
scroll through the available stations.
3. Press the Tuning control to select the desired station. The display
may show 'Connecting...' while the radio re-tunes.
4. Use the Volume control to set the sound level as needed.
Note:
If the display shows 'Service Not Available' it may be necessary to
relocate your radio to a position giving better reception.
A question-mark in front of the station name merely indicates that
the station has not recently been detected by the radio. It may still
be available.
Secondary services - DAB
1. Certain radio stations may have one or more secondary services
associated with them. If a station has a secondary service associated
with it the display will show “>>” next to the station name on the
station list. The secondary service will then appear immediately
after the primary service as you press the Tuning control.
2. Press and release the Tuning control to select the station. Most
secondary services do not broadcast continually and if the selected
service is not available, the radio will re-tune to the associated
primary service
14
Display modes
Your radio has a range of display options when in DAB mode:1. Press the Info button to cycle through the different options.
a. Text Displays text messages such as
the artist or track name, phone in
number, traffic alerts, etc.
b. Program Type Displays the type of station being
listened to such as Pop, Classic,
News etc.
c. Multiplex Name/Frequency Displays the name of the DAB
multiplex to which the current station
belongs as well as its broadcast
frequency.
15
d. Time & Date Displays the current Time & date.
e. Frequency & channel
Displays frequency and channel
number for the currently tuned
DAB station.
f. Bit rate and audio type
Displays the digital bit rate and
audio coding information for the
station being listened to.
g. Signal error/strength
Displays the signal error and
strength for the station being listened
to. A lower error number indicates
a better quality of radio signal.
The signal strength graph can be
used when positioning the radio
or its antenna. For good reception
the graph should occupy three or
more blocks.
Finding new stations - DAB
From time to time, new DAB radio stations may become available.
Or you may have moved to a different part of the country. In this
case you may need to cause your radio to scan for new stations.
GB
1. Press and release the Menu button until the Advanced DAB
menu shows on the display.
2. Rotate the Tuning control until ‘Full scan’ is shown on the display.
3. Press the Tuning control to initiate the scan. The display will
show 'Scanning' and your radio will perform a scan of the DAB
Band III frequencies. As new stations are found the station counter
will increase and stations will be added to the list. The bar graph
indicates the progress of the scan.
4. Alternatively press Auto tune button to scan for new stations.
16
Manual tuning - DAB
Manual tuning allows you to tune your radio to a particular DAB
frequency in Band III. Any new stations found will be added to the
station list. This function can also be used to assist the positioning of
the antenna or the radio to optimize reception for a specific channel
or frequency.
1. Press and release the Menu button until the Advanced DAB
menu shows on the display.
2. Rotate the Tuning control until the display shows 'Manual tune'.
3. Press and release the Tuning control to enter the manual tuning
mode.
4. Rotate the Tuning control to select the desired DAB channel.
5. Press and release the Tuning control. The open block in the signal
strength graph shows the minimum signal strength needed for
good DAB reception. The signal blocks will go up and down
showing the changing signal strength as you adjust the antenna
or the radio position. Any new radio stations found on the tuned
DAB multiplex will be added to the list stored in the radio.
6. Press and release the Tuning control to return to normal tuning
mode.
17
Dynamic Range Control (DRC) - DAB
The DRC facility can make quieter sounds easier to hear when
your radio is used in a noisy environment.
GB
There are three levels of compression:
DRC Off No compression applied. (default)
DRC High Maximum compression applied.
DRC Low Medium compression applied.
1. Press the Power button to switch on your radio.
2. Press and release the Source button until the DAB band is selected.
3. Press and release the Menu button until the Advanced DAB
menu shows on the display.
4. Rotate the Tuning control until 'DRC ' appears on the display.
Press and release the Tuning control. The display will show the
current DRC value which will be marked with an asterisk.
5. Rotate the Tuning control to select the required DRC setting
(default is off).
6. Press and release the Tuning control to confirm the setting. After
several seconds the display will return to the normal radio display.
Note:
Not all DAB broadcasts are able to use the DRC function. If the
broadcast does not support DRC, then the DRC setting in the radio
will have no effect.
18
Station order setup
Your radio has 2 station order settings from which you can choose.
The station order settings are, alphanumeric and ensemble.
Note: The default station order on your radio is ensemble.
1. Press the Power button to switch on your radio.
2. Press the Source button as needed to select DAB radio mode.
3. Press the Menu button to enter the Advanced DAB menu shows
on the display.
4. Rotate the Tuning control until 'Station order' is shown on the display.
5. Press the Tuning control to enter the station order adjustment mode.
6. Rotate the Tuning control to choose between 'Alphanumeric'
and, 'Ensemble' .
'Alphanumeric' - sorts the station list alpha-numerically 0...9 A...Z.
'Ensemble' - organizes the station list by DAB multiplex.
The current setting is indicated by an asterisk.
7. Press the Tuning control to select the required station order.
19
Prune stations - DAB
Over time, some DAB services may stop broadcasting, or may
change location and then not be able to receive a station. In order
to remove such stations from the DAB station list, the Prune stations function will delete the DAB stations from your station list that
can no longer be received.
Stations which cannot be found or which have not been received
for a very long time are shown in the station list with a question
mark.
1. Press the Power button to switch on your radio.
2. Press and release the Source button until the DAB mode is selected.
3. Press and release the Menu button until the Advanced DAB
menu shows on the display.
4. Rotate the Tuning control until 'Prune' appears on the display.
Press and release the Tuning control to enter the setting.
5. Rotate the Tuning control to highlight 'Yes'. Press and release
the Tuning control to cause the stations list to be pruned, eliminating
unavailable stations.
6. If you do not wish to prune stations highlight 'No' in step 5 and
then press and release the Tuning control. The display will revert
back to the previous display.
Note:
If you have moved to a different part of the country you should also
carry out a search for new stations (please see the section 'Finding
new stations' in the previous section).
20
GB
Operating your radio - FM auto-tune
1. Straighten up the antenna.
2. Press the Power button to switch on your radio.
3. Press and release the Source button until the FM band is selected.
4. Press and release the Auto tune button to cause your radio to
search from low frequency to high frequency and to stop automatically
when it finds a station of sufficient strength.
5. After a few seconds the display will update. The display will show
the frequency of the signal found. If the signal is strong enough
and there is RDS data present then the radio may display the
station name.
6. To find other stations press the Auto tune button as before. When
the end of the waveband is reached, your radio will recommence
tuning from the opposite end of the waveband.
7. Adjust the Volume to the required setting.
8. To switch off your radio, press the Power button.
Note:
If you find that FM reception is poor, try repositioning the antenna.
21
Manual tuning - FM
1. Straighten the antenna.
GB
2. Press the Power button to switch on your radio.
3. Press and release the Source button until the FM band is selected.
4. Rotate the Tuning control to tune to a station. The frequency will
change in steps of 50kHz. If the radio is tuned to a station of sufficient
signal strength with RDS information present, then the display
may change to show the station name.
5. When the waveband end is reached the radio will recommence
tuning from the opposite waveband end.
6. Set the Volume to the desired setting.
22
Display options - FM
Your radio has a range of display options for FM mode:The Radio Data System (RDS) is a system in which inaudible digital information is transmitted in addition to the normal FM radio
programme. RDS offers several useful features. The following are
available on your radio.
1. Press and release the Info button to cycle through the various
options.
a. Scrolling text
Displays scrolling text messages such
as artist/track name, phone in number,
etc.
b. Programme type
Displays type of station being listened to
e.g. Pop, Classic, News, etc.
c. Multiplex name
Displays the name of the FM multiplex
to which the current stations belongs.
d. Audio type
Displays the audio type for the currently
tuned FM station.
e. Time
Displays the current time.
f. Date
Displays the current date.
Note:
If no RDS information is available, the radio will be unable to display
the station name, scrolling text and programme type information.
23
Scan sensitivity setting - FM
Your radio includes a local/distant option for the auto-scan function. By setting the radio to the 'local' scan option, weaker signals
from more distant transmitters can be ignored by the radio, making
stronger signals easier to find.
1. Press and release the Power button to switch on your radio.
2. If needed, press and release the Source button until the FM
band is selected.
3. Press and release the Menu button until the Advanced FM menu
shows on the display.
4. Rotate the Tuning control until ‘FM Scan Zone” 'shows on the
display. Press and release the Tuning control to enter the scan
sensitivity adjustment mode. The current setting will be marked
with an asterisk.
5. Rotate the Tuning control to switch between 'Local' (Strong stations
only) and 'Distant' (All stations) options on the lower line of the
display. The Distant option will allow the radio to find weaker signals
when scanning
6. Press and release the Tuning control to confirm your selection.
The Local or Distant setting is stored in the radio and remains in
force until changed or until a System Reset.
24
GB
Presetting stations - DAB and FM
You may store your preferred DAB and FM radio stations to the
preset station memories. There are 10 memory presets in your radio 5 for DAB and 5 for FM. Presets are memorized by your radio
in the event of a power failure.
The procedure for setting presets and using them to tune stations
is the same for FM and DAB mode, and is described below.
1. Press the Power button to switch on the radio.
2. Press the Source button to select the DAB or FM waveband.
3. Tune to the required station as previously described.
4. Press and hold the Preset button until the display shows, such
as,‘Preset 1 stored.’The station will be stored under the chosen
preset button. Repeat this procedure as needed for the remaining
presets.Stations stored in preset memories may be overwritten
by following the above procedure.
Recalling a preset station- DAB and FM
1. Press the Power button to switch on the radio.
2. Press and release the required waveband by pressing the
Source button.
3. Press and release the required Preset button to cause your radio
to tune to the station stored in preset memory.
Note:
The display will show 'Preset Empty' if no station has been stored
to that preset.
25
Listening to music via Bluetooth streaming
You need to pair your Bluetooth device with your radio before you
can auto-link to play/stream Bluetooth music through yourU4 DBT.
Paring creates a `bond' so two devices can recognize each other.
GB
Pairing your Bluetooth device for the first time
1. Press the Power button to switch on the radio.
2. Press the Source button to select the Bluetooth mode.
The Bluetooth status indicator (
to show the radio is discoverable.
) on the panel flashes blue
3. Activate Bluetooth on your device according to the device's user
manual to link to the speaker. Locate the Bluetooth device list
and select the device named ‘U4 DBT”. With some mobiles
(which are equipped with earlier versions than BT2.1 Bluetooth
device, you may need to input the pass code “0000”).
4. Once connected, the Bluetooth icon will remain in solid blue.
You can simply select and play any music from your source device.
Volume control can be adjusted from your source device, or directly
on your radio.
Note:
1) If 2 Bluetooth devices, pairing for the first time, both search for
your radio, it will show its availability on both devices. However, if
one device links with this unit first, then the other Bluetooth device
won't find it on the list.
2) If you take your source device out of range, the connection will
be temporarily disconnected to your radio. Your radio will automatically
reconnect if the source device is brought back in range. Be aware
that during the period of disconnection, no other Bluetooth device
can pair or link with your radio.
26
3) If ‘U4 DBT” shows in your Bluetooth device list but your device
cannot connect with it, please delete the Sangean U4 DBT item
from your list and pair the device with the speaker again following
the steps described previously.
4) The effective operation range between the system and the paired
device is approximately 10 meters (30 feet). Any obstacle between
the system and the device can reduce the operational range.
5) Bluetooth/NFC connectivity performance may vary depending
on the connected Bluetooth devices. Please refer to the Bluetooth
capabilities of your device before connecting to your radio. All
features may not be supported on some paired Bluetooth devices.
Playing audio files in Bluetooth mode
When you have successfully connected your radio with the chosen
Bluetooth device you can start to play your music using the controls
on your connected Bluetooth device.
1. Once playing has started adjust the volume to the required setting
using the Volume control on your radio or on your enabled Bluetooth
device.
2. Use the controls on your device to play/pause and navigate
tracks. Alternatively, control the playback using Play/Pause
,
Next track
, Previous track
buttons on the radio.
Note:
1) That not all player applications or devices may respond to all of
these controls.
2) Some mobile phones may temporarily disconnect from your radio
when you make or receive calls. Some devices may temporarily
mute their Bluetooth audio streaming when they receive text
messages, emails or for other reasons unrelated to audio streaming.
Such behaviour is a function of the connected device and does
not indicate a fault with your radio.
27
Pairing a different device to your radio
Before pairing another device to the speaker, you need to make the
radio discoverable.
1. Press and hold the Bluetooth pair button to make the radio discoverable
again and the Bluetooth status indicator flashes.
2. Follow step3-4 in the previous section of ‘Pairing your Bluetooth
device for the first time.
Playing previously-paired devices
This unit can memorize up to 8 sets of paired device, when the
memory exceed this amount, the earliest paired device will be over
written.
If your Bluetooth device already paired with the speaker previously,
the unit will memorize your Bluetooth device and it attempts to reconnect with a device in memory which is last connected. If the last
connected device is not available, the speaker will be discoverable.
Alternatively, you can select your required Bluetooth device in the
memory, as following:
Press and release the Bluetooth pair button to enter the Bluetooth
device memory. Then rotate the Tuning control to find the desired
memorized Bluetooth device and press the Tuning control to connect to the required Bluetooth device.
Alternatively, repeatedly press and release the Bluetooth pair button to have access to the stored Bluetooth device and press the
Tuning control to connect to the required Bluetooth device.
Disconnecting your Bluetooth device
Press the Source button to select any bands other than Bluetooth
band. Alternatively, press and hold the Bluetooth pair button to disconnect the link.
If you disconnect the Bluetooth device when you are in Bluetooth
mode, the LED light for Bluetooth icon will then start to flash indicating Bluetooth is discoverable again for pairing.
28
GB
Pairing and playing your device via NFC
U4 DBT is equipped with wireless NFC (Near
Field Communication) feature, allowing
playing NFC-enabled devices to pair and
play the music. For non-NFC devices, please
refer to the above sections for standard
Bluetooth pairing.
1. Turn on your NFC feature on your device. (Important: Please
make sure the screen of your playing device is on and unlocked
to allow NFC to work.)
2. Touch the NFC area of your playing device against the NFC area
marked on top panel of U4 DBT. The unit will turn on and enter
automatic pairing mode. If you pair with U4 DBT for the first time,
your NFC-enabled device will be asked the permission to link
with the radio. Once paired with a device, the Bluetooth icon will
remain illuminated.
3. Use the controls on your device or on your radio to play/pause
and navigate tracks.
Note:
1. If you would like to link a different Bluetooth device for the first
time via NFC, disconnect the currently- linked Bluetooth device first.
2. The location of the NFC detection area is not the same on all devices.
When connecting with other Bluetooth device via NFC, refer to
the User guide of your Bluetooth device for more information.
3. Some of metallic case or cover for mobile phones may reduce
the sensitivity of NFC. Make sure you remove it, before activating
the NFC.
Disconnecting your NFC-enabled device
To disconnect your device, simply touch it again on the top of the
unit. The LED light for Bluetooth icon will then start to flash indicating
your radio is discoverable again for pairing.
(Important: Please make sure the screen of your playing device is
on and unlocked to allow NFC to work.)
29
Alarms
Your radio has 2 separate alarms which can be set to wake you to
DAB, FM radio or buzzer alarm. Each alarm can be set to sound
once, daily, on weekdays or at weekends. The alarms can be set
whether the radio is on or in standby mode. In the event of a power
interruption your radio has a built in memory chip that will maintain
your alarm settings for when the power is restored.
Note:
If no buttons are pressed for a while, the radio will exit the alarm
setup.
Setting an alarm
1. Press and release the Alarm 1 button to enter the setting, ‘Alarm
1 Setup’ will show on the display and alarm 1 icon
will flash on
the display. Or press and release the Alarm 2 button to enter
alarm 2 setting.
2. Press the Tuning control to enter the setting menu.
3. Rotate the Tuning control to select On or Off. If Off is selected
any current setting for that alarm will be cancelled. With ‘On’ selected,
press and release the Tuning control to cause the alarm hour digits
to flash on the display.
4. Rotate the Tuning control to choose the desired hour for the alarm
and then press the Tuning control to cause the alarm minute digits
to flash on the display.
5. Rotate the Tuning control to choose the desired minute for the
alarm and then press the Tuning control. The alarm duration will
flash on the display. If the radio has been set to the 12 hour clock
format, there will also be an option here for setting AM or PM for
the alarm time
30
GB
6. Rotate the Tuning control to choose the alarm duration. Choose
between 15, 30, 45, 60 or 90 minutes. Press and release the
Tuning control to confirm the alarm duration.
7. The alarm source option will flash on the display. Rotate the
Tuning control to choose the desired source for the alarm (DAB,
FM, Buzzer). Press the Tuning control when the desired source
alarm is shown on the display. For which ever radio mode is selected,
the radio alarm may be set to any of the stations which have
been stored as presets or to the station last listened to.
8. Press and release the Tuning control to confirm the selection.
The alarm day option will flash on the display.
9. Your alarm can be set to sound once, daily, weekdays and
weekends.
Once - Will sound at one time only.
Daily - Will sound every day.
Weekdays - Will sound only on weekdays.
Weekends - Will sound only on weekends.
10. Rotate the Tuning control to choose the day option and then
press and release the Tuning control to confirm the setting.
* If setting alarms to daily, weekdays or weekends proceed to
point 14.
* If selecting the alarm to once you will need to set the day,
month and year options as described from step 11-13.
31
11. Rotate the Tuning control to select the correct day and
then press the Tuning control to confirm the setting.
GB
12. Rotate the Tuning control to select the correct month and then
press the Tuning control to confirm the setting.
13. Rotate the Tuning control to select the correct year and then
press the Tuning control to confirm the setting.
14. Rotate the Tuning control to choose the desired volume and
press the Tuning control to confirm the setting. Your radio will
show 'Alarm Saved' and will exit the alarm setting procedure.
Note:
Active alarms are indicated in the display by the alarm symbol
(e.g.
). If the radio cannot connect to the radio station, buzzer
alarm will be used instead. The alarm will sound for the selected
duration unless cancelled.
Cancelling alarms
1. While am alarm is sounding, it can be cancelled by pressing
the Power button.
2. To cancel the alarm before going off, enter the alarm setting
wizard and set the alarm On/Off option to ‘Off’ (Please refer to
previously described ‘setting an alarm’ section). Alternatively,
press the required alarm button and rotate the Tuning control to
select ‘off.’
32
Snooze
1. When the alarm sounds, press any button other than the Power
button will silence the alarm for 5 minutes. Remaining snooze
time will show on the display.
2. You can also select your required snooze time, as following:
a. Access the menu for the current mode by pressing the Menu
button.
b. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
c. Rotate the Tuning control until 'Snooze Duration' appears on the
display. Press and release the Tuning control.
d. Rotate the Tuning control to select the desired snooze time. The
options are 5, 10, 15, 20 minutes.
3. To cancel the snooze time while the alarm is suspended, press
the Power button.
33
Sleep function
Your radio can be set to turn off after a preset time has elapsed.
The sleep setting can be adjusted between 15, 30, 45, 60, 90 and
120 minutes.
1. Access the menu for the current mode by pressing the Menu button.
2. Rotate the Tuning control until ‘Sleep’ is shown on the display.
Press the Tuning control to enter the setting menu.
3. Rotate the Tuning control to select the desired sleep time. The
options are 15, 30, 45, 60, 90, or 120 minutes. Use the OFF option
to cancel the sleep function.
4. Your radio will switch off after the preset sleep time has elapsed.
5. To cancel the sleep function before the preset time has elapsed,
either set the sleep timer to off (step 1-3) or press the Power button.
34
GB
Automatically updating the clock
1. Press the Power button to switch on your radio.
2. Press and release the Menu button until the Advanced menu of
the current mode shows on the display.
3. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
4. Rotate the Tuning control until 'Time' appears on the display.
Press and release the Tuning control.
5. Rotate the Tuning control until 'Auto update' appears on the display.
Press and release the Tuning control.
6. Rotate the Tuning control to choose an update option from 'Update
from Any', 'Update from DAB', Update from FM' or 'No update' as
required. The current update option will be marked with an asterisk.
Press and release the Tuning control to confirm your choice. The
radio will exit to the previous menu.
Note:
If you select 'Update from Any', 'Update from DAB', Update from
FM' the current time received will be displayed. If no signal is found
you should either position the radio or its antenna so that a signal
can be received, or revert to manual clock mode.
35
Setting the clock manually
Your radio will set its clock automatically using the DAB or FM radio
signal. If no signal is available and you need to set the time manually,
please follow the procedure shown below.
GB
1. Press the Power button to switch on your radio.
2. Press and release the Menu button until the Advanced menu of
the current mode shows on the display.
3. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
4. Rotate the Tuning control until 'Time' appears on the display.
Press and release the Tuning control.
5. Rotate the Tuning control until 'Set Time/Date' appears on the
display.
6. Press and release the Tuning control. The hour digits will flash
on the display.
7. Rotate the Tuning control to set the desired hour. Press and release
the Tuning control.
8. The minute digits will flash on the display. Rotate the Tuning
control to set the desired minute. Press and release the Tuning
control.
If the radio has been set to use a 12 hour format, there will be
an option here for setting AM or PM for the clock time.
9. The day will flash on the display. Rotate the Tuning control to
change the day as needed. Press and release the Tuning control.
10. The month will flash on the display. Rotate the Tuning control to
set the current month. Press and release the Tuning control.
11. The year will flash on the display. Rotate the Tuning control to
set the current year. Press and release the Tuning control to
confirm the clock setting. The display will show 'Time Saved'
then exit the menu.
36
Setting the time format
The display used in standby mode and when the radio is in use
can be set to 12 or 24 hour format. The selected format is then also
used when setting the alarms.
1. Press the Power button to switch on your radio.
2. Press and release the Menu button until the Advanced menu of
the current mode shows on the display.
3. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
4. Rotate the Tuning control until 'Time' appears on the display.
Press and release the Tuning control.
5. Rotate the Tuning control until 'Set 12/24 hour' appears on the
display. Press and release the Tuning control.
6. Rotate the Tuning control to select either 12 or 24 hour format.
The current hour format will be marked with an asterisk. Press
and release the Tuning control If the 12 hour clock format is chosen,
the radio will then use the 12 hour clock for setting of alarms,
and will display a 12 hour clock with an AM or PM indicator.
37
Setting the date format
1. Press the Power button to switch on your radio.
GB
2. Press and release the Menu button until the Advanced menu of
the current mode shows on the display.
3. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
4. Rotate the Tuning control until 'Time' appears on the display.
Press and release the Tuning control.
5. Rotate the Tuning control until ‘Set date format’ shows on the
display. Press and release the Tuning control.
6. Rotate the Tuning control to select your desired date format. The
current format will be marked with an asterisk. Press and release
the Tuning control.
38
Language function
Your radio can be configured to a different language.
1. Press the Power button to switch on your radio.
2. Press the Menu button until the Advanced menu of the current
mode shows on the display.
3. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
4. Rotate the Tuning control until 'Language' appears on the display.
5. Press and release the Tuning control to enter the language
adjustment menu.
6. Rotate the Tuning control until your desired language appears
on the display.
7. Press and release the Tuning control to confirm your choice. The
display will change to the chosen language.
39
Equalizer function
The sound of your sound system can be adjusted to suit your personal
taste for the material that you are listening to. Your radio has six
preset equalizer modes. Alternatively, you may set the treble and
bass levels to your own preferences.
1. Press the Volume control and rotate the Tuning control to cycle
through the various modes. Press the Tuning control to confirm
the option.
a. My EQ (Treble/Bass - tone setting may be adjusted/Loudnesson/off may be adjusted)
b. Normal-no tone modification is applied
c. Classic
d. Jazz
e. Pop
f. Rock
g. Speech
40
GB
Set up my EQ profile
If you find the preset equalizer functions not to your liking, you may
set up a custom treble and bass as following:
1. Press the Volume control to enter EQ menu.
2. Rotate the Tuning control until ‘My EQ’ is shown on the display.
Press the Tuning control to enter the adjustment mode.
3. Rotate the Tuning control until ‘Treble’ is shown on the display.
Press the Tuning control to enter the treble adjustment mode.
4. Rotate the Tuning control to adjust the treble level (between-5
and+5). The sound will change as you adjust the level. Press
the Tuning control to confirm the setting. The display will then revert
to My EQ menu.
5. Rotate the Tuning control until ‘Bass’ is shown on the display.
Press the Tuning control to enter the adjustment setting. Rotate
the Tuning control until the desired level (between -5 and +5) is
displayed. The sound will change as you adjust the level. Press
the Tuning control to confirm the setting.
6. Rotate the Tuning control until ‘Loudness’ is shown on the display.
Press the Tuning control to enter the adjustment setting. Rotate
the Tuning control to select the desired setting. The options are
On or Off.. the default is Off. Then press the Tuning control to
confirm the setting.
Note:
To quickly cancel the effect of My EQ profile, rotate the Tuning
control until ‘Normal’ is shown on the display and press the Tuning
control. The treble and bass settings will be memorized for the next
time that you wish to use the My EQ.
41
Software version
The software display cannot be altered and is just for your reference.
GB
1. Press the Power button to switch on your radio.
2. Press the Menu button until the Advanced menu of the current
mode shows on the display.
3. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
4. Rotate the Tuning control until 'SW Version' appears on the display.
5. Press and release the Tuning control. The software version
shows on the display.
6. Press and release the Menu button to exit the software version display.
42
Software upgrades
Software updates for your radio may be
available in the future. As software updates
become available software and information
on how to update your radio can be found at
http://sg.sangean.com.tw/first/first.asp
http://www.sangean.eu/
www.sangean.com.au.
For more information, please contact our Head Office by sending
an email to info@sangean.com
1. Plug the USB into the USB socket in the battery compartment.
2. Press the Menu button to enter the Advanced menu of the
current mode.
3. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
4. Rotate the Tuning control until 'Software Upgrade' appears on
the display. Press and release the Tuning control.
5. Rotate the Tuning control until 'Yes' is highlighted on the display.
If you do not wish to carry out a software upgrade, highlight 'No'
and then press the Tuning control. The display will revert back to
the previous display.
43
System reset
If your radio fails to operate correctly, or some digits on the display
are missing or incomplete carry out the following procedure.
GB
1. Press the Power button to switch on your radio.
2. Press the Menu button until the Advanced menu of current mode
shows on the display.
3. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
4. Rotate the Tuning control until 'Factory Reset' appears on the
display. Press and release the Tuning control.
5. Rotate the Tuning control until 'Yes' is highlighted on the display
and press and release the Tuning control. A full reset will be performed.
The station list and presets will be erased. Alarms will be cancelled
and sleep timer settings will be set to their default values. The
display will show 'Welcome to Digital Radio' and the unit will behave
as when first switched on.
If you do not wish to carry out a system reset, highlight 'No' and
then press the Tuning control. The display will revert back to the
previous display.
In case of malfunction due to electrostatic discharge, reset the
product using the above procedure. In some circumstances it may
be necessary to disconnect and then reconnect the mains power in
order to resume normal operation.
44
Setting the Backlight timeout
Your radio can be set to timeout the backlight. The backlight timeout
setting can be adjusted between ON,10, 20, 30, 45, 60, 90, 120
and 180 seconds.
1. Access the menu for the current mode by pressing the Menu button.
2. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
3. Rotate the Tuning control until ‘Backlight’ is shown on the display.
Press the Tuning control to enter the setting menu.
4. Rotate the Tuning control to select the desired time. The options
are on (backlight will be on all the time),10, 20, 30, 45, 60, 90,
120, or 180 seconds.
5. Your radio will switch off the backlight after the preset time has
elapsed.
Auxiliary input socket
A 3.5mm Auxiliary input socket is provided on the right side of your
radio to permit an audio signal to be fed into the unit from an external
audio device such as an iPod, MP3 or CD player.
1. Connect a stereo or mono audio source (for example, iPod, MP3
or CD player) to the Auxiliary input socket (marked 'Aux In').
2. Press the Power to switch on your radio.
3. Press the Source button until the Auxiliary Input band is selected.
4. Adjust the Volume control on your iPod, MP3 or CD player to
ensure an adequate signal and then adjust the volume on the radio
for comfortable listening.
Note: Never use the Aux-In socket in rainy or moist conditions to
prevent moist from entering the radio. Always keep the rubber cover
on the back well closed under these conditions.
45
Charging with USB socket
You can use the USB jack charging function by following the procedure
below.
GB
1. Press the Power button to switch on your radio.
2. Press and release the Menu button until the Advanced menu of
the current mode shows on the display.
3. Rotate the Tuning control until 'System ' appears on the display.
Press and release the Tuning control.
4. Rotate the Tuning control until 'USB Charge' appears on the display.
Press and release the Tuning control.
5. Rotate the Tuning control to select the desired setting. The options
are On or Off.. the default is Off.
Note:
1) The USB jack can only provide power for the USB memory stick
only with 1A 5V maximum and most of iPhone models. However,
it does not support external Hard disk drive, all types of mobile
phones and electronic device.
2) The maximum volume of the output power speaker will decrease
when your USB is charging.
Important:
1) Do not connect this USB socket with your PC USB port, as it
highly possible may cause breakdown of the unit.
2) Never use the USB socket in rainy or moist conditions to prevent
moist from entering the radio. Always keep the rubber cover on
the back well closed under these conditions.
46
Specifications
Frequency Coverage:
FM 87.50 – 108MHz
DAB 174.928 – 239.2MHz
AC Power:
AC 100 ~ 240V / 50 / 60Hz / 40W ( Europe )
Batteries: 6 x UM-1 ( D size )
DC IN:
12V / 1.2 A center pin positive ( operational voltage 9-14V )
5.5 mm in diameter.
Bluetooth
Bluetooth specification
Profile Support
Bluetooth Audio CODEC
Transmitting Power
Line of sight range
Bluetooth® Ver 3.0
A2DP, AVRCP1.4
SBC, AAC
Specification Power Class 1
10 meters / 30 feet
Output Power:
4W 10% T.H.D. @ 100Hz @ DC battery 9V
7W 10% T.H.D. @ 100Hz @ AC 230V or 110V
Aux in socket:
3.5 mm diameter, stereo jack to be mixed as monaural
Input sensitivity: 300m Vrms at output 7W @ 1000Hz
Input impedance: 47kohm
47
DC Out: USB Socket, 5V 1000mA
GB
Speaker unit:
6.5 inches 8 ohm 15W, full range
FM / DAB / DAB + bended spring antenna
LED illuminator:
2 x white LED, current consumption 30mA
Battery life:
Approx. 36 hours using Alkaline batteries at 500mW output power.
Dimension: 298 X 342 X 268
Weight: approx. 4.4kgs
The company reserves the right to amend the specification without notice.
If at any time in the future you should need to dispose of this product
please note that: Waste electrical products should not be disposed
of with household waste. Please recycle where facilities exist. Check
with your Local Authority or retailer for recycling advice. (Waste
Electrical and Electronic Equipment Directive)
48