Access Fit 220V Electric Projection Screen by Draper - AV-iQ

Installation/Operating Instructions
Access Fit 220V Electric Projection Screen by Draper
Caution
1 Read instructions through completely before proceeding; keep them
for future reference. Follow instructions carefully. Installation contrary to
instructions invalidates warranty. Care in mounting and correct operation
will mean long and satisfactory service from your Draper screen.
2 Before removing screen from crate, check for damage and to make sure
all parts are included.
3 Allow enough access to remove front cover should fabric become
damaged or should other service be required.
4 Screen should be installed level (using a carpenter’s level).
5 Nothing should be fastened to screen dowel or viewing surface.
6 Operating switch(es) is packed separately in screen carton. Do not
discard with packing material.
7 Screen operates on 220V, 50 Hz. 1.1 amp current draw.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
These instructions are meant as a guide only. They do not imply any responsibility on the
part of the manufacturer for improper installation or faulty workmanship at the jobsite.
Hanging Screen
When locating viewing surface and checking clearance for screen operation,
remember surface is centered in the length of the case. Regardless of
mounting method used, the following points apply:
1 Mounting brackets are shipped attached to the case. Engage each bracket
with top of housing as shown below and tighten set screws.
2 Screen should be positively and securely supported so that vibration or
even abusive pulling on viewing surface will not weaken installation.
Please Note: A Hoisting Bracket is included on each end of the case to
aid in overhead installation of the Access Fit case.
3 Installer must insure that fasteners used are of adequate strength and
suitable for the mounting surface chosen. Supporting hardware (chains,
cables, 9.5mm rods, etc.) must be essentially vertical.
Figure
Figure
22mm
7 "
ELECTRICAL
/8
CUTOUT
ELECTRICAL
CUTOUT
Electrical Connections
Screen operates on 220V, 50 hz., 1.1 amp current draw.
Duty Cycle: ON 28 seconds /OFF 4 minutes.
Junction box is located just above the bottom access panel at left end of
screen (standard, right end may be specified).
Remove the bottom access panel for access to the junction box cover. (See
Bottom Access Panel Removal instructions below). Remove two (2) hex head
screws that secure the cover to the junction box to expose the red, black, and
white pigtail leads and the green ground wire per wiring diagram on page 4.
If optional low voltage control is specified and factory installed, please refer to
wiring diagrams on page 4.
Screen is shipped with internal wiring complete and control switch(es) fully
boxed. Wire to connect screen to switch(es) and switch(es) to power supply
should be furnished by installer. Connections should be made in accordance
with attached wiring diagram, and wiring should comply with national and
local electrical codes.
All operating switches should be “off” before power is connected.
Bottom Access Panel Installation/Removal
Bottom access panel is secured to the screen housing by two screws (one on
each end), and is held in the closed position by engagement brackets with ball
detents that snap into case support brackets.
Access Fit
case as seen
from below
Bottom flange of
Access housing
Figure
Bottom Access Panel Door
Caution: Beware of pinch points at ends of closure
To remove the Access Panel:
1 Remove screws from both ends of screen housing (Fig. 4).
2 Pull down on the access panel until the ball detents on the engagement
bracket have disengaged from the support bracket.
3 Repeat Step 2 for all brackets along the length of the screen housing.
4 The access panel will be free to pivot downward. It will remain attached to
the lower inside edge of the screen housing by several steel hinges.
N
EE G
R
SCUSIN
HO
Alternate
Installation
(additional set of
brackets required
but not included)
Typical
Installation1
L
ED NE
OS S PA
L
C ES
C
AC
EN
OP ESS
C L
AC NE
PA
With typical installation, brackets may be angled to meet installation requirements.
1
4 Entire bottom of case must be readily accessible after installation is
complete.
5 Front, back and top of case must be straight— not forced to warp or bow.
6 If case is painted on location, removal of roller/fabric assembly is
recommended prior to painting. If not removed, slot on bottom of case
should be shielded to protect viewing surface from paint splatters/overspray.
7 Do not seal unit in ceiling until electrical connections have been made
and screen has been operated successfully.
Access
Panel Door
pivot on Hinges
Remove Screws
from both ends
of Screen Housing
Figure
Caution: For larger sizes Step 5 requires two people to perform safely.
5 Press up on access panel and pull toward the front of the screen housing to
disengage hinges and remove access panel.
To Remove/Install Support Brackets:
Figure
E
CA
S
of
TE
R
C
of
CE
N
ER
NT
Printed in U.S.A
E
AS
CE
Form AccessFit220V_Inst17
ACCESS PANEL
SUPPORT BRACKET
1
Suitable for use in environmental air space in accordance with Section
300-22(c) of the National Electrical Code, and Sections 2-128, 12-010(3) and
12-100 of the Canadian Electrical Code, Part 1, CSA C22.1.
Copyright © 2017 Draper Inc.
US Patent Nos.
6,137,629; 6,421,175;
6,532,109; 6,816,308;
7,559,707
ATTACHING BRACKETS
Insert pin in top
slot and push up
Rotate bracket
clockwise to lock
bracket in place
ENGAGEMENT BRACKET
WITH BALL DETENT
will snap into Access
Panel Support Bracket.
2
If you encounter any difficulties installing or servicing your Access Fit screen, call
your dealer or Draper, Inc., in Spiceland, Indiana, 765/987-7999 or fax 765/987-7142.
Access Fit 220V Instructions by Draper
page 2 of 4
Tab-Tension Adjustment Procedure for Access Fit/Series V
Motorized Roller/Fabric Installation
TO
IN C
ADJUSTMENT
SCREW
REASE TE
LEASE T
R E N T E R- C E N S
LO I
TO CO U
C
N
CLOCKW S
O
RN
IS E
TU
KW
DOWEL
N
www.draperinc.com
ADJUSTMENT
SCREW
URN
Operation
When screen is first operated, be cautious! Cycle unit down and up several times
to confirm satisfactory operation.
220V SINGLE STATION CONTROL—3-position UP-OFF-DOWN switch permits
operation to be stopped at any point. Factory adjusted limit switches automatically
stop screen when fully down or fully up.
220V MULTIPLE STATION CONTROL—Switches are similar in appearance
to 110-120V Single Station Control. Screen stops when switch is released and
may be restarted in either direction. Factory adjusted limit switches stop screen
automatically when fully up or fully down.
24V CONTROL—Three-button UP-STOP-DOWN switches stop at any point
desired, operate in any sequence. Factory adjusted limit switches automatically
stop screen when fully up or fully down. Installer should incorporate an all-pole
disconnect in the fixed wiring available with RF or IR remote.
220V & 12V VIDEO INTERFACE CONTROL—Allows screen to be controlled by
trigger signal—when the signal comes on, the screen descends automatically.
Two versions: Model VIC115 integrates screen operation with a Draper video
projector lift or a video projector or tuner with a 220V switched outlet. Model VIC12
interfaces with a 12V switched outlet. Both available with an override switch (VIC–
OS), permitting independent operation. VIC–OS not available with factory installed
VIC115 & VIC12.
KEY OPERATED SWITCHING—Two kinds of key-operated switches are
optionally available with this unit. 1 The key-operated power supply switch controls
power to the screen and switches. When it is “off”, the switches will not operate
screen. Key may be removed from the switch in either “on” or “off” position.
2 A three-position key switch permits the screen to be operated directly by key.
In this case, the screen’s operator must always have a key.
RS232/ETHERNET—Serial communication and network communication optionally
available with wall switches, RF or IR remote.
Figure
E
Motorized Roller/Fabric Removal
Reverse the instructions above “Motorized Roller/Fabric Installation” for removal of
the unit.
TENSIONING
CABLE
TENSIONING
CABLE
IS
Figure
9 The roller/fabric assembly and roller brackets may need to be slid left or right in
the mounting channel of case to center fabric within screen case.
10 Securely tighten the set screws on roller mounting brackets.
11 Connect the electrical plug from the motor to the mating socket on the junction box.
12 Reinstall the bottom access panel as previously described.
1 Determine which side requires adjustment.
2 Secure dowel with one hand.
3 Using Phillips-head screwdriver, depress spring-loaded adjustment screw
and slowly turn CLOCKWISE TO INCREASE tension, or
COUNTER-CLOCKWISE TO RELEASE tension. The screw adjusts in 60° turn increments. Adjust only one increment (60°) at a time.
NT
CAUTION: Failure to replace the washer and retaining clip could
result in the separation of the roller from the brackets.
Draper’s Tab-Tensioning System is factory-set, and under normal circumstances
will not require field adjustment. If, however, you notice wrinkles, waves or other
indications that the tensioning cables need to be adjusted, follow the procedure below.
IO
Please note: When ordering a motor with internal Low Voltage Controller,
if the case ships separate from the "guts," the case includes the 2.36m cable and
special low voltage switch.
Figure
1 The bottom access panel must be removed first. (Pg 1, Fig. 4).
2 The motor end mounting bracket has a metal bracket
Motor roller
with snap ring for accepting motor head. Back out the assembly
two set screws in bracket until they are flush with top
Washer
side of bracket.
3 To engage the motor end bracket flange above the
two channels in the top of the screen housing, rotate
the bracket approximately 45° counterclockwise to
allow the top surface of the motor bracket to rest flat
Retaining
against the top inside of the housing.
clip
4 Rotating the bracket clockwise until it is engaged with
the channels, slide it along the length of the housing
Idler end roller
mounting bracket
against the electrical junction box.
Motor End
Set Screws
5 Engage idler end bracket (rectangular
Mounting
Bracket
mounting pad) in the same manner as
motor end bracket and slide it toward the
opposite end of the screen housing.
Motor End
Retaining Clip
Do not tighten set screws on this bracket
until the roller/fabric assembly is
installed, and centered in case.
Note: Step 6 requires two people to perform safely.
6 Locate the black washer and retaining clips attached to the instruction sheet.
Raise the roller/fabric assembly up into the screen housing and engage the
head of the motor completely into the motor mounting
bracket, making sure the limit switch adjusting knobs are
visible from the bottom of the screen housing (see fig. 8).
If snap ring is provided, make sure the snap ring engages with
the motor. If retaining clip is provided instead, install to lock
motor end in place.
7 While supporting the idler end of the roller, slide the idler end
mounting bracket toward the roller. Insert the roller pin into the
nylon bushing on the idler end mounting bracket.
8 The roller idler pin needs to go through the idler bracket far
enough to allow the washer and retaining clip to be reinstalled
on the pin.
DOWEL
4 If problem is not corrected, leave screen in position for 24 hours to allow
surface material to stretch into position.
5 If problem still is not corrected, repeat steps 2 and 3.
Limit Adjustments (Standard/Quiet Motors)
Please Note: Screen limits are factory set for optimum performance of the screen. A
procedure is outlined below for minor tweaks, but any adjustment of these limits may
negatively affect the flatness of the screen surface and could also void the warranty.
Please check with Draper prior to resetting screen limits.
CAUTION: Always be prepared to shut screen off manually when new adjustment is
being tested. Screen may be severely damaged if viewing surface is allowed to run too
far up or too far down.
CAUTION: Be sure all switches are in “off” position before adjusting limit switches.
The motor limit screws are normally located on the audience left of screen roller.
**Please Note: If the Access Fit E/V is “Right Hand Motor” or “Waterfall”, the WHITE/
DOWN (I) and YELLOW/UP (II) limit screws are reversed. See graphic below.
"Down" Limit Adjustment
To Reduce Screen Drop
1 Raise screen surface about 1' above desired setting and turn off.
2 Turn the WHITE/DOWN (I) limit screw clockwise (three screw turns = ½ roller
revolution).
3 Test by running screen down and repeat steps 1 and 2 until desired position is
reached.
To Increase Screen Drop
1 Run screen to the down limit.
2 With the down switch on, turn the WHITE/DOWN (I) limit screw counterclockwise
(3 turns of screw equals ½ roller revolution) to increase drop.
3 Test by running screen up about 1' and back down to new down limit.
4 Repeat steps 2 and 3 until desired position is reached.
"Up" Limit Adjustment
Screen is Running Too Far Up
1 Lower screen surface about 1' below desired setting and turn off.
2 Turn the YELLOW/UP (II) limit screw clockwise (3 screw turns = ½ roller
revolution).
3 Test by running screen up.
4 Repeat steps 1 through 3 until desired position is reached.
Screen Needs to Run Up More
1 Run screen down about 1' and turn off.
2 With the up switch on, turn the YELLOW/UP (II) limit screw counterclockwise (3
turns of screw equals ½ roller revolution).
3 Repeat steps 1 and 2 until desired position is reached.
CAUTION: Do NOT allow the dowel to wrap up over the roller when the
screen is running up! This could damage the screen.
Figure
Audience
Side
Motor
End
Audience
Side
Standard Roll
Motor
End
Reverse Roll
Standard/Reverse Roll
Left hand motor
White Socket—Down
Yellow Socket—Up
Right hand motor
White Socket—Up
Yellow Socket—Down
(765) 987-7999
Audience
Side
Motor
End
Waterfall Roll
Waterfall Roll
Left hand motor
White Socket—Up
Yellow Socket—Down
Right hand motor
White Socket—Down
Yellow Socket—Up
Access Fit 220V Instructions by Draper
page 3 of 4
Limit Adjustments (Low Voltage Motors with Internal Low Voltage Controller)
Please Note: Screen limits are factory set for optimum performance of the
screen. A procedure is outlined below for minor tweaks, but any adjustment of
these limits may negatively affect the flatness of the screen surface and could
POSITION
also void
the warranty.FUNCTION
Please check with Draper prior to resetting screen limits.
limitto shut screen off manually when new
DOWN
CAUTION:
AlwaysSet
be LOWER
prepared
adjustment is being tested. Screen may be severely damaged if viewing
UP
surface is allowed
toSet
runUPPER
too farlimit
up or too far down.
CAUTION: Be sure all switches are in “off” position before adjusting limit
Normal Operation
switches.
CENTER
Back View of Wall Switch
To Motor
with
Built-In
Low Voltage
To Motor
with
Built-In
Low Voltage
Please Note: If you move the slider switch from down to up in one motion it
sets the two limits in the same position.
Figure
Please Note: 5V DC must be
connected to be able to set
limits using the wall switch.
Slide
Switch
C
o
+ m
m
5V o
DC n
POSITION
FUNCTION
DOWN
Set LOWER limit
UP
Set UPPER limit
D
o
w U
n p
4 Set the slide switch to the higher position. Move the viewing surface to desired
upper limit by pressing and holding the UP button on wall switch.
5 Return the slide switch to the center position to return to normal operation.
6 To set the viewing surface to an alternate format position, move theviewing surface
to the desired position and press the STOP button. Press and hold the STOP
button for at least three seconds to record the position.
Normal Operation
CENTER
Back View of Wall Switch
To Motor
with Low Voltage Controller,
Please note: When ordering a motor with internal
Built-In
if the case ships separate from the "guts,"
case includes the 7.6m cable
Lowthe
Voltage
and special low voltage switch.
CASE LENGTH
457mm
Please Note: Pressing and releasing the UP button on the switch will move the
screen to its upper limit. Pressing and releasing the DOWN button will move the
screen to its lower limit.
While the motor is in motion, pressing the STOP button for less than two
seconds will stop the viewing surface at its present position.
Once the motor is stopped, pressing the STOP button will move the viewing
surface to its alternate format position.
Pressing and holding the STOP button, when the motor is at rest or in
motion, for at least three seconds will record a new alternate format position.
Case Dimensions
Slide
Switch
To Motor
with
Built-In
Low Voltage
1 Connect the ILT switch to the motor via the terminal blocks, or via the modular port
using four conductor modular cable. When using modular cable, the cable
connectors MUST NOT be crimped in reverse, as with standard telephone cable.
(For a Dry Contacts Wiring Diagram, see page 4.)
2 Set the slide switch to the lower position. Press and hold the DOWN button on the
switch to move the viewing surface to the desired lower limit. If the screen moves in
the opposite direction, release the DOWN button and press and hold down the
STOP button for four seconds. This will reverse the operation of the UP and DOWN
switches.
3 Move slider switch into center position.Wait a couple of seconds.
C
o
+ m
m
5V o
DC n
D
o
w U
n p
457mm
19mm
LEVELING BRACKET**
35mm TYP
22mm
Center
of Case
137mm
203mm
L*
L*
17mm
17mm
*L = Varies
For minimum ceiling cutout subtract 38mm from case length and width (measured from outer edge of flanges).
ACCESS FIT
Mounting Bracket Dimensions
Mounting Bracket Dimensions
197mm
13mm
11mm
29mm
**There are several knockouts in the screen housing
to allow the Leveling
Bracket to be adjusted
laterally (up to 41cm in
either direction)
11mm
13mm
16mm
35mm
51mm
3mm
38mm
R 5mm
R 6mm
144mm
130mm
22mm
6mm
TYP.
14mm
73mm
TYP.
76mm
87mm
165mm
16mm
124mm
197mm
164mm
www.draperinc.com
(765) 987-7999
32mm
Access Fit 220V Instructions by Draper
page 4 of 4
Wiring Diagrams—220V Motor and Quiet Motor
Wiring Diagrams—220V Standard Motor
Single
Low
Voltage
Control
Multiple
Controls
with
InternalLow
LowVoltage
Voltage Controller
Single
SingleStation
StationControl/Einstationsbedienung/
Control/Einstationsbedienung/
Multiple
MultipleStation
StationControl/Mehrstationsbedienung/
Control/Mehrstationsbedienung/
Commandemonoposte
monoposte
Commande
Commande
Commandemultiposte
multiposte
CE
CEApproved/CE-zugelassen/Homologuée
Approved/CE-zugelassen/HomologuéeCE
CE
Internal
InternalScreen
ScreenWiring/Interne
Wiring/Interne
Projektionsflächenverkablung/Câblage
Projektionsflächenverkablung/Câblageinterne
internededel'écran
l'écran
Blue/Blau/Bleu-220v
Blue/Blau/Bleu-220v(Common/Gemeinsam/Commun)
(Common/Gemeinsam/Commun)
Brown/Braun/Marron-220v
Brown/Braun/Marron-220v(Down/Ab/Bas)
(Down/Ab/Bas)
Black/Schwarz/Noir-220v
Black/Schwarz/Noir-220v(Up/Auf/Haut)
(Up/Auf/Haut)
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Green-Yellow/Grün-Gelb/Vert-jaune
Green-Yellow/Grün-Gelb/Vert-jaune
(Motor
(MotorGround/Motorerdung/
Ground/Motorerdung/
mise
miseà àlalaterre
terredudumoteur)
moteur)
Green-Yellow/Grün-Gelb/Vert-jaune
Green-Yellow/Grün-Gelb/Vert-jaune
(Motor
(MotorGround/Motorerdung/
Ground/Motorerdung/
mise
miseà àlalaterre
terredudumoteur)
moteur)
Black/Schwarz/Noir
Black/Schwarz/Noir
Blue/
Blue/
Blau/
Blau/
Bleu
Bleu
Neutral
Neutral
L1
L1
Red/Rot/Rouge
Red/Rot/Rouge
Neutral
Neutral
Hot/
Hot/
Stromführend/
Stromführend/
Chaud
Chaud
Black/Schwarz/Noir
Black/Schwarz/Noir
220v,
220v,5050Hz.
Hz.
to additional motors
Wall Switch,
RF or Data
IR Cable Connection
Receiver,
Back of
Wall Switch
TO MO
TOR
or integrated
Data Cables to
switches or
MOTOR
control system
to additional motors
DATA CABLE
Dashed
Dashedwiring
wiring
bybyinstaller/
installer/
Gestrichelte
GestrichelteVerkabelung
Verkabelung
To 220V Line
durch
durchInstallateur/
Installateur/
Câblage
Câblageenenpointillés
pointillés
par
parl'installateur
l'installateur
Wall Switches,
RF or IR
Receivers,
or integrated
control
systems
Please Note:
This Splitter/Jack
To 220V Line
TO MO
TOR
TO MO
TOR
Dry Contacts
MOTOR
DATA CABLE
Data Cables to
switches or
to additional motors
MOTOR
DATA CABLE
is located inside the junction
box of your Access screen.
Switch - to - Motor OR
Connection
Back of
Data Cable Connection
Wall Switch
*These wiring diagrams are for Access
Fit screens with motor on audience left
(standard), and fabric unrolling from
the back of the roller (standard).
Data
Data Cables to
Cables
switches or
TO MO
TOR
MOTOR
DATA CABLE
Control
Control
Blue/
Blue/ switches/
switches/
Blau/
Blau/ Kontrollschalter/
Kontrollschalter/
Bleu
Bleu Commutateurs
Commutateurs
dedecommande
commande
Red/Rot/Rouge
Red/Rot/Rouge
220v,
220v,
5050Hz.
Hz.
by electrician
Data
Cable Connection
Data Cable
Blue/
Blue/
Blau/
Blau/
Bleu
Bleu
Black/Schwarz/Noir
Black/Schwarz/Noir
Control
Control
switch/
switch/
Kontrollschalter/
Kontrollschalter/
Commutateur
Commutateurdedecommande
commande
Dashed wiring
Dashed wiring
by electrician
Red/Rot/Rouge
Red/Rot/Rouge
Dashed
Dashedwiring
wiring
bybyinstaller/
installer/
Gestrichelte
GestrichelteVerkabelung
Verkabelung
durch
durchInstallateur/
Installateur/
Câblage
Câblageenenpointillés
pointillés
par
parl'installateur
l'installateur
Internal Screen Wiring
Not
NotCE
CEApproved/Nicht
Approved/NichtCE-zugelassen/Non
CE-zugelassen/Nonhomologuée
homologuéeCE
CE
White (Neutral)
Internal
InternalScreen
ScreenWiring/Interne
Wiring/Interne
Projektionsflächenverkablung/Câblage
Projektionsflächenverkablung/Câblageinterne
interne
dedel'écran
l'écran
Black
Blue/Blau/Bleu-220v
Blue/Blau/Bleu-220v(Common/Gemeinsam/Commun)
(Common/Gemeinsam/Commun)
Green (Ground)
Brown/Braun/Marron-220v
Brown/Braun/Marron-220v(Down/Ab/Bas)
(Down/Ab/Bas)
Black/Schwarz/Noir-220v
Black/Schwarz/Noir-220v(Up/Auf/Haut)
(Up/Auf/Haut)
Please Note: This Splitter/Jack
is located inside the junction
box of your Access screen.
OR
Back of
Wall Switch
TO MO
TOR
Back of
Dry Contacts
Wall Switch
MOTOR
DATA CABLE
Please Note: This Splitter/Jack
is located inside the junction
box of your Access screen.
OR
Internal LVC-IV
Single or Multiple
Dry -Contacts
Projection Screen Wiring Diagram
TO MO
TOR
INTERNAL SCREEN WIRING
Back of
Wall Switch
MOTOR
DATA CABLE
Green/Yellow
(Motor Ground)
Green/Yellow (Ground)
Brown (Down)
Black (Up)
Blue (Common)
Red-to screen (directional)
Brown-to screen (directional)
White -Common to screen & 230V AC Neutral
Receiver
Button
To
230 VAC
Line
L1
Location of key
operated on-off
switch if furnished.
FUSE - 3.15 AMP
250 VAC 5x20mm
GND
Please Note: 5V DC must
be connected to set limits
using the wall switch.
Dashed wiring by electrician
Low voltage wiring by others
Blue (Common)
Black (Up)
Brown (Down)
Green/Yellow
(Motor Ground)
N
To
230 VAC L1
Line
GND
Electrically Straight
Data Cable to more
LVC-IV modules*
RS232/485
Inputs/Outputs
Low Voltage
Trigger
3-28 VDC
IR Eye Input
Wall Switch
*A maximum of six (6)
LVC-IV modules can be
linked together.
External LVC-IV - Single or Multiple
Projection Screen Wiring Diagram
White-Common to screen & 230V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 230V AC-Hot
Black-to 230V AC-Hot
Green/Yellow (Ground)
Location of key
operated 0n-off
switch if furnished.
Receiver
Button
FUSE - 3.15 AMP
250 VAC 5x20mm
INTERNAL SCREEN WIRING
3 Button Wall Switch
DOWN
- Black
Please
Note: 5V
DC must
be connected
to set limits
COM - White
using the wall switch.
UP - Red
Back of
Yellow-to 230V
WallAC-Hot
Switch
Black-to 230V AC-Hot
N
Please Note: 5V DC must
be connected to set limits
using the wall switch.
Electrically Straight
Data Cable to more
LVC-IV modules*
RS232/485
Inputs/Outputs
Low Voltage
Trigger
3-28 VDC
Dashed wiring by electrician
Low voltage wiring by others
www.draperinc.com
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
IR Eye Input
(765) 987-7999
Wall Switch
*A maximum of six (6)
LVC-IV modules can be
linked together.