www.CookWithKenyon.com
T E X A N G RILL
OWNERS MANUAL
Part # 143641
Created: July 13, 2009
Revised: August 26, 2014
Table of Contents
Section
Page
Important Safeguards ..............................................................................................................3
How to use Grill
Quick Start Tips ...............................................................................................................4
Stuffed French Toast........................................................................................................ 7
Product Specifications ............................................................................................................ 8
Installation Instructions
Package Contents ........................................................................................................... 9
Electrical Requirements .................................................................................................10
Countertop Installation ...................................................................................................10
Drain Connection ............................................................................................................12
Final Preparations Prior to Use .......................................................................................12
Operation of Grill
Touch Control .................................................................................................................14
Grill Parts .......................................................................................................................17
Lid Removal ...................................................................................................................18
Handle Lock ...................................................................................................................19
Warranty Information .............................................................................................................20
2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed
including the following:
1. Read ALL instructions prior to using product.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against electrical shock, do not immerse cord or plugs in water or other liquid.
4. Close supervision is necessary when any appliances are used near children.
5. Allow to cool before putting on or taking off parts.
6. Do not operate appliance with a damaged power cord or plug. If the appliance malfunctions,
discontinue use and contact the nearest authorized appliance dealer or the factory for examination,
repair or adjustment.
7. The use of accessory attachments not supplied by the manufacturer of the appliance may cause
injuries.
8. Suitable shelter must be provided to prevent direct exposure to rain. Covers available.
9. Do not place on or near a hot gas or electric burner, or in a heated oven.
10. Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.
11. Do not use appliance for other than intended use.
12. Always place a minimum of one (1) cup of water in disposable drip tray prior to grilling.
13. Never leave children alone - children should not be left unattended around the grill at any time.
14. Allow the grill to cool before taking off cooking grates, disposable drip tray or lids.
15. Fuel, such as charcoal briquettes, are not to be used with this appliance.
16. Ensure grill is installed per instructions and properly grounded by a qualified electrician.
17. Do not replace or attempt to repair any part of the grill, unless otherwise noted in this manual.
All other service is to be performed by a factory authorized technician.
18. Do not use water to extinguish a grease fire, use dry chemical fire extinguisher.
19. Do not store flammable materials near the grill.
20. Do not wear loose fitting or hanging apparel when using the grill.
PLEASE READ THESE INSTRUCTIONS IN THEIR
ENTIRETY BEFORE INSTALLATION
AND USE.
SAVE THESE INSTRUCTIONS
3
Q U I C K
S TA R T
T I P S
Thank you for purchasing the World’s Finest All Seasons® Electric Grill!
There are a few simple
steps you can take to ensure your good decision will lead to years of World-Class Grilling:
1.
Remove grate(s) and drip tray(s), clean both.
2. Insert the drip tray(s) into the bottom of grill. Make sure the burner brackets are not
resting on the drip tray(s).
VISIT OUR WEBSITE
to purchase recipe books, cooking utensils,
griddles, grill covers, and more!
3. Always fill the drip tray(s) with 16 oz. of liquid. Water will work, but why not try beer or
wine to add flavor to your favorite food. Then re-install cooking grate.
4. Depending on model, either hardwire your Kenyon All Seasons® Grill or plug it directly into
an outlet, do not use extension cords.
5. Preheat grill for 5 to 9 minutes on high (8 bars). Adjust heat setting for type of food,
for example:
-Vegetables 3-4 bars
-Pork and fish 4-5 bars
-Burgers 6-7 bars
-Steak 7-8 bars
6. Close lid and cook. Enjoy the best grilled food you have ever tasted!
7. Once your grilling session is complete, grab a wet paper towel and wipe down your grate.
Once cool, place in the dishwasher along with the dirty dishes so that it’s ready for its
next tour of duty!
8. While the grate is in the wash, don’t forget to clean out the drip tray contents.
You don’t want your previous juices to flavor your next meal.
www.CookWithKenyon.com | 860.664.4906 |
Scan with
smartphone
REMOVE & READ PRIOR TO GRILLING
HOW TO USE GRILL
THE ABOVE INSERT IS LOCATED
UNDERNEATH YOUR GRILL LID.
PLEASE READ INSERT AND REMOVE
PRIOR TO GRILL USE.
4
1. Before using your grill, remove the cooking grate and drip tray from the grill. Wash the
grill with warm soapy water using a non-abrasive cloth. USE ONLY HIGH TEMP PLASTIC
UTENSILS WHEN GRILLING. Visit our web site to purchase a set of high quality stainless steel/
high temp plastic grill utensils, www.cookwithkenyon.com.
2. Make sure the drip trays are inserted all the way into the bottom of grill
and electric element brackets are resting on the element support bracket.
3. Cover the bottom of the drip trays with a liquid. Water is fine. PLEASE
DO NOT USE A FLAMMABLE LIQUID! Doing so
would ruin your cookout. Using apple juice if you are
grilling pork adds a nice flavor to the meat. A can of
lime soda is wonderful if you are grilling fish. Try any
kind of liquid that you enjoy drinking. Just remember always add liquid
to the drip tray prior to grilling.
4. To keep your grill smoke free, always clean the grilling surface
after each use. Simply wash with warm soapy water using a
non-abrasive cloth or place in your dishwasher. Empty the drip
trays and wipe with a damp paper towel. The drip trays can be
used multiple times before needing to be replaced.
5. Place your cooking grates or optional griddles (part #B96000) onto the element with drip trays
installed. Use the griddles for foods such as eggs, pancakes or my favorite - stuffed french toast!
6. Preheat grill for 5 to 9 minutes on high (8 bars illuminated). Adjust heat setting for type of food.
• Steak and hamburgers 8 bars
• Chicken, pork and fish 6 bars
• Vegetables 5 bars
7. Close the lid(s) and cook. Enjoy the best grilled food you have ever tasted!
8. Clean up. This is easy to do as you will soon learn. After the grill has cooled to the touch, take
a few pieces of paper towel and place on the grilling surface. Pour about one ounce of water on
the towel and then using your high temperature nylon tongs, swab the paper toweling back and
forth to loosen up the residue from your grilling. Throw the paper towel away and wipe the grates
off with a dry paper towel.
9. Once the grates have cooled sufficiently, remove the grates and place in your dishwasher for a
thorough cleaning.
10. With the grates removed, lift up the electric elements and remove the drip trays. Empty the
contents of the drip trays in an appropriate place, please don’t pour it on your neighbors lawn.
Wipe the trays out with a dry paper towel and reuse the trays. The trays can last for many uses.
11. After you have used your grill many times, you may want to wash the lids. They can be
placed in your dishwasher and run on the pots & pans cycle. This will restore your grill to its
original pristine look.
5
Grate
Drip Tray
Electric
Elements
Fig. 1
12. To clean the grill, first be sure the cooking surface has cooled enough to handle. Then
remove the grates, lift up the electric elements until they lock in the up position, remove the
middle grate support cross bar, then the drip trays. The grate support cross bar is removed by
lifting the rear and pulling the front notch off of the supporting tab. To install the support reverse
the procedure. Do not cook on the grill without the support in place!
13. Wipe the stainless steel surfaces with a damp cloth to remove any residue
from previous grilling sessions.
14. Your Kenyon grill came with a sample bottle of stainless steel cleaner.
Use this cleaner once a month to keep your grill looking like new.
15. The touch control area is ceramic glass which is sealed from the effects of rain, snow and
ice. To clean the glass, use a glass cleaner and soft towel. If stains appear, use a ceramic glass
cleaner which can be found in your local grocery store.
6
Stuffed French Toast
16 slices
1 lb.
½ cup
4 T.
Thin Sliced Bread “any kind but not the white stuff”
Cream Cheese (softened)
Peach Preserves (or your favorite)
Butter
French Toast Batter:
5
Large eggs thoroughly beaten
1 cup Milk
1 T. Cinnamon, ground
½ t. Allspice, ground
½ t. Coriander, ground
2 oz. Water (Dark Rum, Optional)
In a large bowl place the eggs and beat with a wire whisk. Add the milk and beat again
until incorporated. In a separate smaller bowl pour water or Rum (if you prefer) and add dry
ingredients, mix thoroughly. Once the dry ingredients have been mixed, add to the egg and milk
mixture and beat again until mixed. By doing this you avoid the clumps that come with making
batter.
Method of Preparation:
This will require the use of your griddle. Preheat your ‘All Seasons Grill’ on medium high heat (6
bars) for approximately ten minutes.
Once the cream cheese has softened mix with the peach preserves. Divide equally onto eight
slices of bread and spread evenly. Place the remaining eight slices on top to make a sandwich.
When your griddle has been preheated, add two tablespoons of butter and move around to coat
the griddle. Reserve the rest of the butter for the remaining pieces of French Toast. Take the
sandwich and dip into the mixture and flip it over to coat both sides of your bread.
Quickly do this to three more “sandwiches”. You will now have four pieces of stuffed French Toast
on your griddle.
Be careful not to burn. Flip the sandwiches over and continue cooking until both sides are
browned nicely.
At this point you either serve with some nicely warmed maple syrup and butter, or you can keep
warm in a low oven until you finish the remaining pieces of French Toast.
7
PRODUCT SPECIFICATION
The Texan Grill
Model B70400 - 240V AC 50/60Hz - 3000 WATTS - 13 AMPS
Overall dimensions: 29” x 21” x 4” (11” with lid)
736mm x 534mm x 114mm
(292mm with lid)
Depth does not include drain fitting - add 2” or 50.8mm
Cut-out dimensions: 28” x 18.5”
711mm x 470mm
24 1/2"
4"
29"
21"
26"
Overall Dimensions
Fig. 2
11"
4"
28"
18 1/2"
Cut-out Dimensions
Fig. 3
8
INSTALLATION
Package Contents
Your Texan grill is assembled and ready for installation. Before you install the grill write your
unit’s serial number here for future reference: _________________. The serial number can be
found on the bottom center of the grill next to the drain fitting. The serial number consists of six
digits.
Contained in the shipping container is the Texan Grill, nine (9) mounting screws, manual,
stainless steel cleaner and three (3) feet of drain hose with brass fitting. If any components are
missing or damaged, call KENYON immediately.
Fig. 4
9
Electrical Requirements
Check the Electrical Supply Requirements
This product must be installed in accordance with national, state and local electric codes. The
following table provides the correct voltage, amperage and frequency that must be supplied to the
grill.
The supply must be from an individual grounded circuit that is protected by a circuit breaker and
rated per the specifications for the model as shown in the table below.
KENYON
Part #
Max Load
Power Supply
B70400 3000 Watts
240V AC 13A 60Hz
Plug Type
Flying leads in flexible conduit (designed to be hardwired into electrical system)
WARNING:
If the electrical supply does not meet the product specifications, consult with a
licensed electrician before proceeding with installation!
Countertop Installation
Your Texan Grill is supplied with a factory installed polished stainless steel flange that accepts
nine oval head wood screws for mounting. The trim flange of the grill is designed to hold the unit
firmly in place in the countertop. If desired, you may seal the edge of the countertop beneath
the trim flange. Use a soft bedding compound that will prevent damage if later removal for
service is necessary. We recommend a nonadhesive type of sealant, such as plumber’s
putty, maximum compressed thickness of 1/16”. Silicone may be used to seal the glass edge
only, if desired. Should you need to remove the unit from the countertop after installation simply
take a piece of fishing line and run back and forth under the trim flange to break the caulk bond.
WARNING:
Allow a 2 inch (2”) minimum clearance between the bottom of the grill and combustible
surface located below, ie: the upper edge of a drawer installed below the grill (Fig. 6, page
11). Failure to provide proper clearances and ventilation may result in a fire hazard.
10
Please read this section prior to making cutout for the grill.
It is important to plan ahead for installation of the grill, keeping the
following dimensions in mind (please refer to Figure 5 below).
A - 13 inches maximum depth of overhead cabinets
B -36 inches is minimum height of countertop above floor
C -The minimum flat countertop surface that the grill will
rest upon must be equal to or greater than the overall
grill dimensions (refer to the page 8 for overall
grill dimensions).
D -30 inches minimum clearance between the top of the
grill and the bottom of an unprotected wood or metal
cabinet or 24 inch minimum clearance when the bottom of wood or metal cabinet is protected by not less
than 1/4 inch thick flame retardant mill board covered with not less than No. 28 MSG sheet steel, 0.015 inch thick stainless steel, 0.024 inch thick aluminum or 0.020 inch
thick copper.
E - 4 inches minimum from backsplash of countertop to edge of
grill (refer to the page 8 for overall grill dimensions).
1-1/2 inches minimum from front of counter to grill.
FOR INSTALLATIONS IN CANADA: “Do Not Install Closer
Than 1/2 Inch (12 mm) From Any Adjacent Surface”, and NE
PAS INSTALLER A’MDINS DE 12MM DETOUTE SURFACE
ADJACENTE.
Fig. 5
Warning:
To eliminate the risk of burns from reaching over heated grill, cabinet storage space
located above the grill should be avoided. If cabinet storage is to be provided, the
risk can be reduced by installing a range hood that projects horizontally a minimum
of 5 inches beyond the bottom of the cabinets.
Before making the countertop cutout, check for clearance. Check to see that the grill will clear
the front and side walls of the base cabinet. Also check for proper clearance to the back splash
so that the lid can open fully.
Adequate ventilation of the space below the countertop must be provided to ensure proper
operation of the grill. Heat transferred from the grill bottom pan during operation will overheat
an improperly ventilated area.
2 INCH (51MM) MINIMUM
Fig. 6
11
When making countertop cutout, radius the corner to help prevent cracking of the countertop
material. A 1/4 inch radius is typical, but follow the countertop manufacturer’s instructions
regarding the minimum radius and any reinforcements required to prevent damage to the
countertop over time.
If your countertop is made of solid surface material you will need to check with the manufacturer
for specific recommendations for cooktop & grill installation instructions. Most solid surface
countertop manufacturers require additional corner supports to prevent damage to the
countertop. Use the included screws to secure the grill to the countertop. Be careful not to
over-tighten the screws. Use an acrylic caulk to seal the flange to the countertop.
If your countertop is made of stone you will need to use an acrylic latex to mount the grill in place.
Put a large bead of caulk around the cutout opening and place the grill in place. Wipe away any
excess caulk, use water to remove the excess caulk. Allow the caulk to dry for a minimum of
24 hours without any moisture being allowed to come in contact with the caulk. Do not use the
screws that came with your grill. The caulk will hold the grill securely. Do not use a caulk which
contains silicone as this will stain the stone.
Drain Connection
For your convenience, the grill is equipped with a 1/2” NPT brass pipe fitting and 90º brass elbow
which you can attach the 5/8” ID flexible hose that came with your grill. The portable version of
the grill comes with a brass pipe plug installed in the drain fitting. If you are using your grill as a
portable unit, save the hose and 90º brass fitting for possible installation in the future.
Drain fitting for 5/8” ID hose
Fig. 7
Final Preparations Prior to Use
Remove the protective plastic film from the lid, trim flange and glass panel. Clean the grill before
you use it for the first time. A thorough cleaning with a stainless steel or glass cleaner will remove
any traces of plastic film adhesives and manufacturing oils.
Wash the nonstick coated grates in warm soapy water before using the grill.
12
OPERATION OF GRILL
DO NOT USE WATER ON GREASE FIRES
Smother fire or flame or use dry chemical or foam-type extinguisher.
USE ONLY DRY POT HOLDERS
Moist or damp pot holders on hot surfaces may result in burns from steam. Do not let pot holder touch the
grate or element of the grill. Do not use a towel or other bulky cloth in place of a pot holder.
DO NOT COOK ON BROKEN GRILL GRATE OR GRIDDLE
If the grate should break, grease and oils may come into direct contact with the electric element and
create a risk of electric shock or fire. Contact an authorized service center or KENYON Customer Care
immediately at (860) 664-4906.
CLEAN GRILL WITH CAUTION
If a wet sponge or cloth is used to wipe spills on a hot cooking surface, becareful to avoid steam burns.
Some cleaners produce noxious fumes if applied to a hot surface. Read the cleaner label for details prior
to using.
DO NOT TOUCH HEATING ELEMENT OR GRATE
The heating element and grate will be hot for some time after cooking. These components should be
allowed to cool and then be handled with care and caution while cleaning, as they may be hot enough to
cause severe burns.
CLEAN GRILL AFTER EACH USE
This appliance is equipped with removable, disposable drip trays. The drip trays MUST be removed and
cleaned after each and EVERY use. Do not allow grease to accumulate between cooking. The drip trays
and baffle tray MUST be used when cooking on the grill. Excessive grease may spill over into the interior
of the grill, voiding your warranty and posing a fire hazard.
NEVER LEAVE GRILL UNATTENDED AT HIGH HEAT SETTINGS
High heat setting may cause heavy smoking and ignite grease.
DO NOT CLEAN UNIT WITH PRESSURIZED WATER
Never clean the grill with any form of pressurized water or other types of cleaners. Doing so will void the
warranty and may pose a serious risk of electric shock. Always clean the grill with a cloth and a stainless
steel or glass surface cleaner.
STORAGE
Suitable shelter must be provided to prevent direct exposure to rain. Covers available.
TO PREVENT SMOKE
To prevent the contents of the drip trays from smoking, place 1 cup of water (or enough to cover the
bottom of the pan) in the drip trays before cooking.
DO NOT USE POTS OR OTHER BAKEWARE ON THE GRILL keep these instructions with the GRILL for future reference
13
Touch Control
To activate an element, first the master
power must be turned on by placing
and holding a finger over the circular
area next to the master power graphic.
An audible beep will be heard and a
light next to the master power graphic
will illuminate. Then the desired
element must be turned on, by placing
a finger over the circular area marked
ON/OFF for that element. The same
beep will sound and a light will
illuminate. Then the heat level is
chosen, by holding a finger over the
circular areas marked with + or -.
Touching the + first will incrementally
set the heat level from settings 1 thru 8
with a beep and corresponding number
of lights illuminated. Touching the - first
will incrementally set the level from
settings 8 thru 1 with a beep and
corresponding number of lights
illuminated. When the desired heat
level is reached the finger is removed
and the grill remains at that heat level.
If an element is activated, but no heat
level chosen, the element will
automatically turn off in 7 seconds.
Power On Indicator
+ Power Sensor
Power Level
Graphic
Master Power Sensor
- Power Sensor
To change the heat level place finger
on + or - graphic of desired element to
change heat level incrementally up or
down.
To deactivate an element, touch circular
area marked ON/OFF to turn the
element off. Also the master power ON/
OFF can be touched and the entire grill
will be deactivated.
Fig. 8
14
CALIBRATION
Upon application of electrical power to the
grill, the controller will run a self-calibration
process. The controller will then sound an
audible confirmation tone and the display will
briefly illuminate. The grill is now ready to be
used.
Fig. 9
HEAT SETTINGS
Your Texan Grill has 8 different heat settings,
1 through 8, selected using the (-) and (+)
sensors. The heat setting is displayed as
shown at the right. The heating element
cycles at different time intervals to vary the
heat level. As the setting is increased, the
heating element will remain on for a longer
period, increasing the cooking temperature of
the grill.
15
POWER
LEVEL
DISPLAY
(HEAT
SETTING 8
SELECTED)
Fig. 10
TURNING “OFF” THE GRILL
To turn off the grill, simply touch and hold the Master Power Sensor for two seconds. The
controller will de-energize and shut off the heating element.
AUTOMATIC SHUT-OFF
The electronic control of your KENYON grill has been programmed with safety in mind and
features an automatic shut-off. The grill is programmed to shut down after predetermined time
after being energized (see table below). The control will also shut off if it reaches a preset
temperature limit. If this occurs, allow the grill to cool down for 20-30 minutes.
PREHEAT AND AUTO SHUT-OFF TIME
The grill will preheat at full power for the specified time and heat settings listed in the table below.
In the number 8 setting there is no preheat as the grill is at full power all ready.
SETTING
PREHEAT TIME (min)
AUTO SHUT-OFF (min)
1
2
3
4
5
6
7
8
1
3
5
5
7
7
7
0
91
91
91
65
67
67
67
60
16
Grill Parts
HEATING ELEMENTS
The heating elements are designed to pivot as
shown to remove/replace the baffle tray and
drip trays. They will stay in the up position. To
put down apply slight downward pressure.
GRATES
BAFFLE TRAY
The baffle tray supports the drip trays, heating
elements and grates and must always be used
when operating the grill. The cross bar must
also be installed to support the elements and
grates.
CROSS BAR
DRIP TRAYS
BAFFLE
TRAY
DRIP TRAYS
The disposable drip trays collect all the fat and
juices created during the cooking process.
The drip trays must be emptied after each use.
When replacing the drip trays, position the drip
trays so that they are completely contained
inside the baffle tray and insuring that the side
or the rim of the drip trays do not protrude
outside of the baffle tray. (see Fig. 12)
HEATING
ELEMENT
To prevent the contents of the drip trays
from smoking, place 1 cup of water (or
enough to cover the bottom of the pan)
in the drip trays before cooking. The
replacement for the disposable drip tray is
Kenyon part #B96001.
Fig. 11
GRATES
Grates must be cleaned after every use. The
grates have a nonstick coating for ease of
cleaning. Wash grates after each use in warm
soapy water.
Element support
bar must be in place
as shown
Drip trays must be contained
inside of heat baffel as shown
Fig. 12
17
Lid Removal
LID REMOVAL
The grill lids are removable for
cleaning . To remove the lids, open
it so the bearing are aligned with
the notch in the lidstay. Pull the
lidstay toward the center of the grill,
over the bearing, releasing the lid
from the lidstay mechanism. Then
slide the quick release pin out of the
middle hinge. (See Fig. 13)
With the quick release pin removed,
grasp the lid, pushing back on the
center to clear the middle hinge and
slide the lid away from the center
of the grill until the outer hinge is
free of it’s pivot pin. (See Fig. 14)
Once the lid(s) have been removed
they can be washed in warm, soapy
water. Installation is reverse of
removal.
Notch in lidstay
Quick release pin
Fig. 13
Fig. 14
18
Handle Lock
HANDLE LOCK
The handle lock allows the user to
lock both lids together for ease of
opening and accessing the entire
grilling surface. (See Fig. 15)
The lids can also be unlocked and
opened individually for access to
either half of the grilling surface.
(See Fig. 16)
Slide & Twist
Unlock
Lock
Handles Locked
Fig. 15
Slide & Twist
Unlock
Lock
Handles Unlocked
Fig. 16
19
This is a great feature allowing the
user to access only half of the grill,
allowing the other half to continue
cooking uninterrupted.
Warranty
Kenyon International, Inc (the “Company”) warrants its products in normal usage to be free of defects in
materials and workmanship subject to the conditions and limitations below.
Any part, which proves to be defective in normal usage during the warranty period will be repaired or replaced
by the Company.
This warranty covers certain products built by the Company and is subject to the following conditions and
limitations:
1.
The Company’s liability shall be limited to repair or replacement (choice of remedy at Company’s
option) of electronic components and grill grate/griddle as may be defective in materials or
workmanship. This liability is limited to three years from the date of original installation or 42 months from invoice date, whichever comes first; this warranty covers parts and labor at approved Company rates, $75 per hour. Stainless steel is warranted with a lifetime guarantee to be rust free, though proper
maintenance of grill is expected. Please refer to the care instructions in owner’s manual. If corrosion begins, contact the Company with photo evidence of corrosion for replacement components.
2.
Determination of suitability of the product for use contemplated by the Buyer, is the sole responsibility
of the Buyer and the Company shall have no responsibility in connection with such suitability.
3.
The Company shall not be liable for any damage resulting from:
•
failures due to use of the product in applications for which they are not intended;
•
failures due to wear and tear, abuse, carelessness, improper installation or maintenance;
•
failures due to breakage of glass, accidental or not.
4.
The Company shall be responsible for ground shipping charges to the location of the appliance (home) within the continental United States and Canada. Any duties, express or special shipping charges are at the expense of the Buyer.
5.
All labor allowed by the Company under this warranty must be performed by an Authorized Kenyon International Service Center, unless otherwise specified in writing by the Company.
THERE ARE NO OTHER WARRANTIES OF MERCHANTABILITY, FITNESS FOR PURPOSE OR ANY OTHER KIND, EXPRESSED OR IMPLIED AND NONE SHALL BE IMPLIED BY LAW. The duration of any such
warranties that are nevertheless implied by law for the benefit of a consumer, shall be limited to a period of
three years from original purchase by the user. Some countries do not allow limitations on how long an implied
warranty lasts, so this limitation may not apply to you.
THE COMPANY SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING
FROM THE BREACH OF THIS WARRANTY, WHETHER EXPRESSD, IMPLIED OR STATUTORY. Some
countries or states do not allow exclusion or limitation of consequential or incidental damages so this limitation
or exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER LEGAL
RIGHTS THAT MAY VARY FROM COUNTRY TO COUNTRY AND STATE TO STATE.
20
Kenyon International, Inc.
P.O. Box 925 • 8 Heritage Park Road • Clinton, CT 06413 USA
Phone: (860) 664-4906 FAX: (860) 664-4907