Upper Arm Blood Pressure Monitor

HEM-7600T-AP3_A_M03_170119.fm 1
• If battery fluid should get on your skin, wash your skin immediately with plenty
of clean, lukewarm water. If irritation, injury or pain persists, consult a doctor.
• Do not use batteries after their expiration date.
• Periodically check your batteries to ensure they are in good working condition.
• Only use batteries specified for this monitor. Use of unsupported batteries may
damage and/or may be hazardous to the monitor.
Upper Arm
Blood Pressure Monitor
Model HEM-7600T
Instruction Manual
1. Know Your Device
Contents:
3125186-3A
Monitor, battery set, instruction manual, setup instructions
Thank you for purchasing the OMRON Upper Arm Blood Pressure Monitor.
Your new upper arm blood pressure monitor uses the oscillometric method of
blood pressure measurement. This means the monitor detects your blood
movement through your brachial artery and converts the movements into a
digital reading. An oscillometric monitor does not need a stethoscope so the
monitor is simple to use.
Important Safety Information
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
• DO NOT adjust medication based on measurement results from this blood
pressure monitor. Take medication as prescribed by your doctor. Only a doctor
is qualified to diagnose and treat high blood pressure.
• DO NOT use this monitor on an injured arm or an arm under medical
treatment.
• DO NOT wear the arm cuff on your arm while on an intravenous drip or blood
transfusion.
• DO NOT apply or inflate the arm cuff around any body parts other than your
upper arm.
• DO NOT use this monitor in areas containing high frequency (HF) surgical
equipment, magnetic resonance imaging (MRI) equipment, computerized
tomography (CT) scanners or in oxygen rich environments.
• DO NOT use this monitor on infants, toddlers, children or persons who cannot
express themselves.
• Consult your doctor before using this monitor if you have common arrhythmias
such as atrial or ventricular premature beats or atrial fibrillation; arterial
sclerosis; poor perfusion; diabetes; pregnancy; pre-eclampsia; or renal
disease.
• Always consult your doctor. Self-diagnosis of measurement results and
self-treatment are dangerous.
• Contains small parts that may cause a choking hazard if swallowed by children,
toddlers or infants.
• Keep the BATTERY out of the reach of children, toddlers and infants.
• This product emits radio frequencies (RF) in the 2.4 GHz band. DO NOT use
this product in locations where RF is restricted, such as on an aircraft or in
hospitals.
Caution
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury to the
user or patient or damage to the equipment or other
property.
• Stop using this monitor and consult your doctor if you experience skin irritation
or discomfort.
• Consult your doctor before using this monitor on an arm with an arterio-venous
(A-V) shunt.
• Note that PATIENT motion, trembling, shivering may affect the measurement
reading.
• Consult your doctor before using this monitor if you have had a mastectomy.
• Consult your doctor before using the monitor if you have severe blood flow
problems or blood disorders as cuff inflation can cause bruising.
• Do not take measurements more often than necessary because bruising, due
to blood flow interference, may occur.
• Remove the arm cuff if it does not start deflating during the measurement.
• Do not use this monitor for any purpose other than measuring blood pressure.
• Do not use a mobile phone or other electrical devices that emit electromagnetic
fields near this monitor except when transferring your readings to your smart
device. This may result in incorrect operation of this monitor.
• Do not disassemble or attempt to repair the monitor or components. This may
cause an inaccurate reading.
• Do not use in a location where there is moisture or a risk of water splashing the
monitor. This may damage the monitor.
• Do not use this monitor in a moving vehicle such as in a car or on an airplane.
• Do not drop, or subject this monitor to strong shocks or vibrations.
• Do not use this monitor in places with high or low humidity or high or low
temperatures. See the “6. Specifications” section of the manual.
• Please check, by observation of the arm being used, that the monitor is not
causing any impairment of patient blood circulation.
• Do not use this monitor in high-use environments such as medical clinics or
doctor offices.
• Avoid bathing, drinking alcohol or caffeine, smoking, exercising and eating for
30 minutes before taking a measurement.
• Rest for at least 5 minutes before taking the measurement.
• Remove tight-fitting or thick clothing from your arm while taking a
measurement.
• Remain still and do not talk while taking a measurement.
• Read and follow the “Important information regarding Electro Magnetic
Compatibility (EMC)” in the EMC information provided with this device.
• Read and follow the “Correct Disposal of This Product” in “6. Specifications”
when disposing of the device and any used accessories or optional parts.
Data Transmission
• Do not replace the battery while your reading is being transferred to your smart
device. This may result in the incorrect operation of your monitor and failure to
transfer your blood pressure data.
• Do not place integrated circuit cards, magnets, metal objects, or other devices
that emit electromagnetic fields near this monitor while your reading is being
transferred to your smart device. This may result in the incorrect operation of
your monitor and failure to transfer your blood pressure data.
Battery Handling and Usage
• Do not insert the batteries with their polarities incorrectly aligned.
• Use only 4 “AAA” alkaline batteries with this monitor. Do not use other types of
batteries. Do not use new and used batteries together.
• Remove the batteries if the monitor will not be used for a long period of time.
• If battery fluid should get in your eyes, immediately rinse with plenty of clean
water. Consult a doctor immediately.
To take a measurement, you need to be relaxed and
comfortably seated, at a comfortable room
temperature.
• Sit in a chair with your legs uncrossed and your feet flat on
the floor.
• Sit upright with your back straight.
• Sit with your back and arm being supported.
• The arm cuff should be placed on your arm at the same level as your heart.
3. Replace the battery cover.
3.3 Taking a Measurement
A.
B.
C.
D.
E.
A
START/STOP button
Connection button
Display
Arm cuff
Battery compartment
When the batteries have been securely placed in this device, the message
and SYNC symbol below will appear on the screen:
D
C
B
E
: Make sure to press the connection button to pair with the smart
device or transfer the data before taking a measurement when
the SYNC symbol “ ” appears.
Display:
F
Please read the Important Safety Information in this instruction manual
before using the unit.
Please follow this instruction manual thoroughly for your safety.
Please keep for future reference. For specific information about your own blood
pressure, CONSULT YOUR DOCTOR.
Warning
3.2 How to Sit Correctly
indicated, into the battery
compartment.
Monitor:
Introduction
Intended Use
This device is a digital monitor intended for use in measuring blood pressure and
pulse rate in adult patient population. The device detects the appearance of
irregular heartbeats during measurement and gives a warning signal with
readings. It is mainly designed for general household use.
2. Insert 4 “AAA” batteries as
F. Systolic blood pressure
G. Diastolic blood pressure
H. Pulse display
G
H
Connection symbol
Battery symbol (low)
Connection OFF symbol
Battery symbol (depleted)
Connection ON symbol
Deflation symbol
Movement error symbol
Heartbeat symbol
(Flashes during measurement.)
SYNC symbol
Cuff Wrap Guide Symbol
Irregular heartbeat symbol
/
Review the list of compatible smart devices at:
omronconnect.com/devices
For details, visit: omronconnect.com
1. Turn on the Bluetooth feature of the smart device.
INFLATING
DEFLATING
COMPLETED
: The arm cuff was wrapped snugly enough.
: The arm cuff was loose or not wrapped correctly.
Note: The cuff wrap guide result appears on the display during the
measurement.
The following symbols indicate incorrect measurement
• If any of these symbols below are displayed, please take another
measurement.
Example:
2. Remove the arm cuff.
3. Transfer your readings.
* If you already have the “OMRON connect” app, go to:
Menu > Devices > Add Device
3. Open the app on your smart device and follow the set-up
and pairing instructions.
4. Confirm the monitor is connected successfully.
Please make sure your monitor is within 5 m (16 ft.) of your smart device
and your “OMRON connect” app is active.
As soon as the measurement is complete, your reading will be
automatically transferred to the app.
Transferring your readings later
1. Open the app on your smart device and then follow the instructions.
2. Press connection button to transfer your readings.
If the monitor is connected successfully to the smart device, “OK” will
appear on the display.
)
• When the SYNC symbol appears on the display, make sure that your
monitor has been pairing with the smart device or transfer the data.
• When the SYNC symbol appears on the display, transfer the data before
the measurements are deleted. If the memory is full, the monitor will be
delete the oldest value. Maximum internal memory is for 100
measurements.
2013 ESH/ESC Guidelines for the management of arterial hypertension
Definitions of hypertension by office and home blood pressure levels
Office
≥140 mmHg
≥90 mmHg
Home
≥135 mmHg
≥85 mmHg
These are from statistical values for blood pressure.
1.2 Before Taking a Measurement
To help ensure an accurate reading, follow these directions:
1. Avoid bathing, drinking alcohol or caffeine, smoking, exercising and
eating for 30 minutes before taking a measurement.
2. Rest for at least 5 minutes before taking the measurement.
3. Stress raises blood pressure. Avoid taking measurements during
stressful times.
4. Measurements should be taken in a quiet place.
5. Remove tight-fitting clothing from your arm.
6. Keep a record of your blood pressure and pulse readings for your
doctor. A single measurement does not provide an accurate indication
of your true blood pressure. You need to take and record several
readings over a period of time. Try to measure your blood pressure at
the same time each day for consistency.
2. Preparation
2.1 Battery Installation
1. Remove the battery cover.
If “Err” appears, refer to “Connection failure. / Data is not being
transmitted.” in section 4.2 for more detail.
)
If the cuff was wrapped too loosely, it may cause unreliable results. If the
wrapping of cuff is too loose, the cuff wrap guide symbol “ ” appears.
Otherwise “ ” appears. This is the function which is used as an aid in
determining if the cuff is wrapped snugly enough.
Gently slip into the gap of the
hook and pull downward.
START
)
The movement error symbol is displayed if you move your body during the
measurement. Please remove the arm cuff, and wait 2 - 3 minutes.
Take another measurement and remain still during measurement.
Systolic Blood Pressure
Diastolic Blood Pressure
The date and time on your monitor will automatically be set when you pair
it with your smart device.
To begin using the “OMRON connect” app for the first time, please visit
omronconnect.com/setup for the initial set-up instructions.
)
When the monitor detects an irregular rhythm
Normal Heartbeat
two or more times during the measurement, the
Pulse
irregular heartbeat symbol will appear on the
Blood pressure
display with the measurement values.
An irregular heartbeat rhythm is defined as a
Irregular Heartbeat
Short Long
rhythm that is 25% less or 25% more than the
Pulse
average rhythm detected while the monitor is
Blood pressure
measuring the systolic and diastolic blood
pressure.
If the irregular heartbeat symbol displays with your measurement results,
we recommend you consult your doctor. Follow the directions of your
doctor.
SYNC Symbol (
The arm cuff will start to inflate.
2.2 Pairing Your Monitor with a Smart Device
your smart device.
Irregular Heartbeat Symbol (
Cuff Wrap Guide Symbol (
1. Press the [START/STOP] button.
2. Download and install the free “OMRON connect” app on
1.1 Display symbols
Movement Error Symbol (
Notes:
• When the depleted battery symbol “
” appears on the display, turn the
monitor off and remove all the batteries. Replace with 4 new batteries at
the same time. Long life alkaline batteries are recommended.
• The measurement values continue to be stored in the memory even after
the batteries are replaced.
• The supplied batteries may have a shorter life than new batteries.
• Disposal of used batteries should be carried out in accordance with the
national/local regulations for the disposal of batteries.
Notes:
• To stop the measurement, press the [START/STOP] button once to
deflate the arm cuff.
• Remain still and do not talk while taking a measurement.
• This device will store 100 measurements in the device. Stored
measurements cannot be viewed on the monitor's display. You will need
to use the “OMRON connect” app to view all measurements prior to the
most recent reading taken.
• Do not use the monitor with other electrical device simultaneously. This
may result in incorrect operation of the monitor.
• If your readings are successfully transferred to your smart device,
“OK” will flash on the display.
Notes:
• Pairing this monitor with the “OMRON connect” app on your smart device
will set the date and time on this monitor. Once you have paired with the
“OMRON connect” app, the date and time is now setup on this monitor,
all future measurements will include the date and time when you transfer.
If you do not pair this monitor to set the date and time, anyࠉ
measurements you take with this monitor will not include the date and
time.
• If you use an app other than the "OMRON connect" app, the date and
time may not be set automatically on your blood pressure monitor.
• Please be aware that OMRON will not be responsible for the loss of data
and/or information.
• If you use the monitor without pairing, refer to the “Using your Monitor
without Pairing” in the “3.3 Taking a Measurement”.
Notes:
• When the SYNC symbol “ ” appears on the display, transfer the data
immediately before the readings are deleted.
• When the Connection OFF symbol “ ” appears on the display, turn on
the Bluetooth feature of your monitor. (Refer to section 3.4)
• Once you send the your readings to the app, the data cannot be resent to
app or smart device.
4. After your readings have been transferred to the “OMRON
connect” app, press the [START/STOP] button to turn off.
3. Using the Device
3.1 Applying the Arm Cuff
Notes:
• The monitor will automatically turn off after 2 minutes.
• Wait 2-3 minutes before taking another measurement. Waiting between
measurements allows the arteries to return to their prior condition to
taking the measurement.
• If you use any other app instead of “OMRON connect”, the data may not
be displayed correctly after sending.
Remove tight-fitting clothing from your left upper arm.
Do not place the arm cuff over thick clothes.
1. Apply the arm cuff to your left upper
arm.
The bottom edge of the arm cuff should be 1
to 2 cm above the elbow. Positioning the
display in clear view of the user makes it
easier to read the results.
If “Err” appears, refer to “Connection failure. / Data is not being
transmitted.” in section 4.2 for more detail.
1 - 2 cm
2. Securely close with the fabric
fastener.
Notes:
• The blood pressure can differ between
the right arm and the left arm, and the
measured blood pressure values can be
different. Omron recommends to always
use the same arm for measurement. If
the values between both arms differ substantially, please check with your
doctor as to which arm to use for your measurements.
• Positioning the monitor with the [START/STOP] button towards the body
makes it easier to use the device.
DO NOT adjust medication based on measurement results from this blood
pressure monitor. Take medication as prescribed by your doctor. Only a
doctor is qualified to diagnose and treat high blood pressure.
Always consult your doctor. Self-diagnosis of measurement results and
self-treatment are dangerous.
Data Transfer With Multiple Smart Devices
Once you transfer your data to a smart device, that data cannot be
transferred again to the same smart device, nor to another smart device.
About Multiple Users
This monitor is recommended for personal use.
When this monitor is used by more than one person, the measurement data
will be combined.
Using your Monitor without Pairing
You can use this blood pressure monitor without pairing to a smart device.
1. Apply the arm cuff. (Refer to section 3.1)
2. Press [START/STOP] button. (Refer to step 1 to 2 in section 3.3)
3. Write down your SYS/DIA and Pulse readings, along with the date and time
of your measurement on a piece of paper to keep a record of your history.
Note: When using this blood pressure monitor without a smart device, you
will not be able to view your prior readings stored in the memory.
HEM-7600T-AP3_A_M03_170119.fm 2
Turn off the Bluetooth in your monitor in the following areas where use of
wireless equipment is prohibited.
• On aircraft • In hospitals • While abroad
Your blood pressure monitor comes with the Bluetooth already turned on.
4.2 Troubleshooting
Problem
Cause and Solution
No power.
No display appears on the
monitor.
Replace all batteries with new ones.
Check the battery installation for proper
placement of the battery polarities.
Refer to section 2.1.
Measurement values appear
too high or too low.
Blood pressure varies constantly. Many
factors including stress, time of day, and how
you apply the arm cuff, may affect your blood
pressure.
Review the section, 3.2 and 3.3.
1. Turn your monitor power off if it is turned on.
2. Press and hold the connection button for more than 10
seconds.
3. Release the connection button when “
The blood pressure monitor might not be
properly placed within the smart device's
transmission range and is too far from the
smart device. If there are no causes of data
transmission interference found near the
blood pressure monitor, move the blood
pressure monitor within 5 m (16 ft.) of the
smart device and try again.
” appears on
the display.
(2 sec.)
(8 sec.)
The Bluetooth feature of the smart device is
turned off. Turn on the Bluetooth feature of
the smart device and your monitor, and try
sending the data again.
4. Press the [START/STOP] button to turn the monitor off.
Note: The monitor will automatically turn off after 2 minutes.
How to turn “ON” Bluetooth
Operate the following step when the power has been off.
Press and hold the connection button for more than 2 seconds and
” appears on the
then release the connection button when “
display.
Connection failure. /
Data is not being transmitted.
3.5 Restoring Your Monitor to the Default Settings
To delete all the information stored in your monitor, follow the instructions
below. Make sure that your monitor is turned off. It is off when the screen is
not showing numbers or symbols.
symbol “ ” and “P” appear on the display, and then press
the [START/STOP] button for more than 5 seconds.
connection button and [START/STOP] button.
The “Clr” will appear on the display when your monitor settings have
reverted back to their original.
3. Press the [START/STOP] button to turn the monitor off.
Notes:
• The monitor will automatically turn off after 2 minutes.
• Reverting to initial settings of this monitor will not delete the information
in the app.
• When using this monitor again, please delete the registration of the
monitor in the app first, and then pair your monitor.
4. Error Messages and Troubleshooting
4.1 Error Messages
Error Display
Solution
Irregular heartbeat is
detected.
Remove the arm cuff. Wait 2
- 3 minutes and then take
another measurement.
Repeat the steps in section
3.1. If this error continues to
appear, contact your doctor.
Movement during
measurement.
Carefully read and repeat the
steps in section 3.3.
Arm cuff is applied
too loosely.
Apply the arm cuff tighter.
Refer to section 3.1.
The batteries are
low.
Recommend replacement of
all 4 batteries with new ones.
Refer to section 2.1.
The batteries are
depleted or battery
polarities are not
properly aligned.
If the number is
shown except 1 to 5.
Immediately replace 4
batteries with new ones.
Refer to section 2.1.
Confirm the batteries are
properly inserted with
polarities correctly aligned.
Refer to section 2.1.
Connection failure.
Data is not being
transmitted.
Refer to “Connection failure.
Data is not being
transmitted.” in section 4.2.
Arm cuff is applied
too loosely.
Apply the arm cuff tighter.
Refer to section 3.1.
The arm cuff was
inflated exceeding
the maximum
allowable pressure,
and then deflated
automatically.
Do not touch the arm cuff
while taking a measurement.
Refer to section 3.3.
Movement during
measurement.
Repeat measurement.
Remain still and do not talk
during measurement.
Refer to section 3.3.
Clothing is interfering
with the arm cuff.
Remove any clothing
interfering with the arm cuff.
Refer to section 3.1.
Device error.
Contact your local OMRON
representative.
Symbol descriptions
Please consult this instruction manual
The blood pressure monitor did not pair
successfully to the smart device. Try to pair
the devices again.
Refer to “Pair Your Monitor with a Smart
Device” in section 2.2.
For more detail, go to “Help” in the “OMRON
connect” app.
Applied part - Type BF
Degree of protection against electric shock (leakage
current)
To indicate generally elevated, potentially hazardous,
levels of non-ionizing radiation, or to indicate
equipment or systems e.g. in the medical electrical
area that include RF transmitters or that intentionally
apply RF electromagnetic energy for diagnosis or
treatment.
Temperature limitation
• Store the device and the components in a clean, safe location.
• Do not use any abrasive or volatile cleaners.
• Do not wash the device and any components or immerse them in water.
• Do not use gasoline, thinners or similar solvents to clean the device.
• Use a soft dry cloth, or a soft cloth moistened with neutral soap to clean
on the monitor and the arm cuff, and then wipe it with a dry cloth.
• Changes or modification not approved by the manufacturer will void the
user warranty. Do not disassemble or attempt to repair the device or
components.
• The accuracy of this blood pressure monitor has been carefully tested
and is designed for a long service life.
• It is generally recommended to have the device inspected every 2 years
to ensure correct functioning and accuracy. Please consult your local
OMRON representatives.
5.2 Storage
Do not store the device in the following situations:
• If the device is wet.
• Locations exposed to extreme temperatures, humidity, direct sunlight,
dust or corrosive vapors such as bleach.
• Locations exposed to vibrations, shocks or where it will be at an angle.
Product category
Electronic Sphygmomanometers
Product description
Upper Arm Blood Pressure Monitor
HEM-7600T
OLED display
Pressure: 0 to 299 mmHg
Pressure: 40 to 260 mmHg
Pulse: 40 to 180 beats / min.
Accuracy
Pressure: ±3 mmHg
Pulse: ±5% of display reading
Inflation
Fuzzy-logic controlled by electric pump
Deflation
Automatic rapid deflation
Measurement method
Oscillometric method
Transmission method
Bluetooth ® low energy technology
Wireless communication
Frequency range: 2.4 GHz (2400 - 2483.5 MHz)
Modulation: GFSK
Effective radiated power: <20 dBm
IP classification
IP 22
Power source
4 “AAA” batteries 1.5V
Battery life
Approximately 300 measurements
(using new alkaline batteries)
Durable period (Service life) Monitor: 5 years
Operating conditions
10°C to 40°C / 15 to 90% RH (non-condensing) /
800 to 1060 hPa
Storage / Transport
-20°C to 60°C / 10 to 90% RH (non-condensing)
conditions
Weight
Monitor: Approximately 240 g
(not including batteries)
Dimensions
Monitor: Approximately 85 mm x 120 mm x 20 mm
(not including the arm cuff)
Arm circumference
22 to 42 cm
Contents
Monitor, battery set, instruction manual, setup instructions
Applied part
Type BF
Protection against electric
Internally powered ME equipment
shock
Model
Display
Cuff pressure range
Measurement range
Atmospheric pressure limitation
or
Artery mark
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S.
and other countries. App Store is a service mark of Apple Inc.
Android, the Google Play logo are trademarks of Google Inc.
What is Blood Pressure?
Blood pressure is a measure of the force of blood flowing against the walls of the
arteries. Arterial blood pressure is constantly changing during the course of the
heart’s cycle.
The highest pressure in the cycle is called the Systolic Blood Pressure; the
lowest is the Diastolic Blood Pressure. Both pressures, the Systolic and
Diastolic, are necessary to enable a doctor to evaluate the status of a patient’s
blood pressure.
What is Arrhythmia?
Arrhythmia is a condition where the heartbeat rhythm is abnormal due to flaws in
the bio-electrical system that drives the heartbeat. Typical symptoms are
skipped heartbeats, premature contraction, an abnormally rapid (tachycardia) or
slow (bradycardia) pulse.
Why is it a Good Thing to measure Blood Pressure at
Home?
Upper curve: systolic blood pressure
200
Many factors such as physical activity,
Lower curve: diastolic blood pressure
anxiety, or the time of day, can influence
150
your blood pressure. A single
100
measurement may not be sufficient for an
accurate diagnosis.
50
6
12
18
24
Thus it is best to try and measure your
Time of day
blood pressure at the same time each
Example: fluctuation within a day (male, 35 years old)
day, to get an accurate indication of any
changes in blood pressure. Blood pressure is typically low in the morning and
increases from afternoon to evening. It is lower in the summer and higher in the
winter.
Manufacturer
OMRON HEALTHCARE Co., Ltd.
53, Kunotsubo, Terado-cho, Muko, KYOTO,
617-0002 JAPAN
EU-representative OMRON HEALTHCARE EUROPE B.V.
Scorpius 33, 2132 LR Hoofddorp,
THE NETHERLANDS
About a wireless communication interference
This Product operates in the unlicensed ISM band at 2.4GHz. In case this
Product is used around the other wireless devices including microwave and
wireless LAN, which operate same frequency band of this Product, there is a
possibility that interference occurs between this Product and such other
devices. If such interference occurs, please stop the operation of other
devices or relocate this Product before using this Product or do not use this
Product around the other wireless devices.
Asia Pacific HQ
OMRON HEALTHCARE SINGAPORE PTE LTD.
438A Alexandra Road, #05-05/08,
Alexandra Technopark, Singapore 119967
www.omronhealthcare-ap.com
Production facility OMRON HEALTHCARE Co., Ltd.
Matsusaka Factory
1855-370, Kubo-cho, Matsusaka-shi,
Mie, 515-8503 Japan
Made in Japan
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
This marking shown on the product or its literature, indicates
that it should not be disposed of, with other household wastes
at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste
disposal, please separate this product from other types of
wastes and recycle it responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can return this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial waste for disposal.
6. Specifications
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by OMRON HEALTHCARE Co., Ltd. is under
license. Other trademarks and trade names are those of
their respective owners.
Humidity limitation
5. Maintenance and Storage
5.1 Maintenance
Calibration and Service
Cause
• This device fulfils the provisions of EC directive 93/42/EEC (Medical Device
Directive).
• This blood pressure monitor is designed according to the European Standard
EN1060, Non-invasive sphygmomanometers Part 1: General Requirements
and Part 3: Supplementary requirements for electromechanical blood pressure
measuring systems.
• This OMRON product is produced under the strict quality system of OMRON
HEALTHCARE Co., Ltd., Japan. The Core component for OMRON blood
pressure monitors, which is the Pressure Sensor, is produced in Japan.
The Bluetooth feature of the blood pressure
monitor is turned off.
Refer to “To turn “ON” the Bluetooth” in “3.4
Turning “OFF” the Bluetooth”.
To protect your device from damage, please follow the directions below:
7. Trademarks
8. Some Useful Information about Blood Pressure
The application on the smart device is not
ready. Check the application then try sending
the data again.
Refer to “Pair Your Monitor with a Smart
Device” in section 2.2. If the “Err” symbol still
displays after checking the application,
contact your local OMRON representative.
Confirm your smart device compatibility with
this monitor at omronconnect.com
1. While holding the connection button down, the Connection
2. When the “Clr” symbol appears on the display, release the
Notes:
• These specifications are subject to change without notice.
• In the clinical validation study, K5 was used on 85 subjects for determination of
diastolic blood pressure.
• This device is clinically investigated according to the requirements of
ISO81060-2:2013.
• This device has not been validated for use on pregnant patients.
• IP classification is degrees of protection provided by enclosures in accordance
with IEC 60529. This device is protected against solid foreign objects of 12 mm
diameter and greater such as a finger, and against oblique falling water drops
which may cause issues during a normal operation.
mmHg
3.4 Turning “OFF” Bluetooth
Download PDF