USER'S GUIDE
76P4 SERIES 220-240V
2
Thank You
3
Safety Instructions
4
Product View
5
Assembly
6-7
8-12
13-14
Operations
Maintenance and Care
Troubleshooting
14
Replacement Parts
15
Warranty
16
Consumer Services
Thanks for buying a BISSELL Cleanview™ Pet Plus Cyclonic
We’re glad you purchased a BISSELL Cleanview Pet Plus cyclonic bagless
vacuum. Everything we know about floor care went into the design and
construction of this complete, high-tech home cleaning system.
Your BISSELL Cleanview Pet Plus cyclonic bagless vacuum is well made, and
we back it with a limited one year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services department, so, should you
ever have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and service of
high quality homecare products like your BISSELL Cleanview Pet Plus
cyclonic bagless vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman, President & CEO
2
www.bissell.com
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance,
basic precautions should be observed,
including the following:
Read all
instructions
before using your
Upright VACUUM.
WARNING:
To
reduce the risk of fire,
electric shock, or injury:
■Do not use outdoors or on wet surfaces.
■Do not leave machine when it is plugged in.
■Do not use with damaged cord or plug.
■If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, return it to a service agent.
■Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over
cord, or expose cord to heated surfaces.
■Do not unplug by pulling on cord. unplug
by grasping plug.
■Do not handle plug or appliance with wet hands.
■Do not expose hair, loose clothing, fingers
or body parts to openings or moving parts.
■Do not pick up hot or burning objects such
as cigarettes, matches, or hot ashes.
■Do not pick up flammable or combustible
materials (lighter fluid, petrol, kerosene, etc.) or
use in the presence of explosive liquids or vapour.
■Do not use appliance in an enclosed space filled
with vapours given off by oil base paint, paint
thinner, some moth proofing substances,
flammable dust, or other explosive or toxic
vapours.
■Not intended for use by persons (including
children) with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been
given supervision or instruction concerning
use of the appliance by a person
responsible for their safety
www.bissell.com
■Young children should be supervised to ensure
that they do not play with the appliance.
■Remove plug from electrical outlet before
cleaning or maintaining the appliance.
■If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent in order to avoid a hazard.
■Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, petrol, etc.).
■Do not allow to be used as a toy.
■Do not use for any purpose other than
described in this User’s Guide.
■Use only manufacturer’s recommended
attachments.
■Do not use with any opening blocked; keep
free of dust, lint, hair, and anything that
may reduce air flow.
■Keep appliance on a level surface.
■Turn off all controls before unplugging.
■Be extra careful when cleaning stairs.
■This appliance is provided with double
insulation. Use only identical replacement
parts.
■Do not use without the dirt container and
filters in place.
■Pay close attention when working around
children.
■Unplug before attaching TurboBrush™ tool.
■Do not pick up hard or sharp objects such as
glass, nails, screws, coins, etc.
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE
This model is for household use only.
IMPORTANT
FOR OPERATION ON A 220-240 VOLT
A.C. 50/60 Hz POWER SUPPLY ONLY.
If your appliance is fitted with a
nonrewireable BS 1363 plug it must not be
used unless a 13 amp (ASTA approved to BS
1362) fuse is fitted in the carrier contained
in the plug. (Spares may be obtained from
your BISSELL supplier). If for any reason the
plug is cut off, it must be disposed of, as it is
an electric shock hazard should it be inserted
into a mains socket.
3
Product view
Cord Clip
Hose Clip
Deluxe
Stretch Hose
Handle
Crevice Tool
Carrying
Handle
Extension
Wand
Twist 'n
Snap™ Hose
Connector
TurboBrush™
Tool
Quick
Release™
Cord Wrap
Quick
Reach™
Handle
Combination
Dusting
Brush/
Upholstery
Tool
Primary
Separator
Hose Wand
Upper Tank
Power
Cord
Hose
Wand Base
Power Switch
Dirt
Container
Handle
Release
Pedal
Foot Hose
Filter Cup
Pre-Motor
Filter
Height
Adjustment
Knob
caution:
Do not plug in your vacuum
cleaner until you are familiar with
all instructions and operating
procedures.
Powerfoot
* The filter media, not the vacuum as a whole, complies
with the IEST-RP-CC001.5 HEPA Standard
4
www.bissell.com
Inner and
Outer
Circular
Filters
Lock ’n
Seal™ Lever
HEPA Media
Post-Motor
Filter*
Headlight
Furniture Protection
Guard
Assembly
The only tool you’ll need to assemble
your vacuum cleaner is a screwdriver.
Attach handle to vacuum
1. Locate the vacuum handle and remove
the screw packet taped to the base of
the handle.
2. Stand the vacuum upright and place the
handle on the top of the vacuum body.
3. Insert the screws into the existing holes
on each side. Tighten securely with a
screwdriver.
WARNING:
Plastic film can be dangerous. To
avoid danger of suffocation, keep
away from babies and children.
Attach vacuum hose and tools
1. Attach the Twist ‘n Snap hose by
lining up the tabs on the base with the
corresponding notches on the back of
the vacuum.
2. Turn the Twist ‘n Snap hose to the right
to lock the hose into place.
3. Grasping the Quick Reach handle, slide
the end of the hose wand into the hose
wand base. Snap the hose into the hose
clip.
NOTE: The powerfoot will not
operate effectively unless the hose
wand is firmly attached.
4. Slide the extension wand and the crevice
tool together into the storage clip on the
side of the vacuum.
5. Snap the combination tool into the
storage clip on the back of the vacuum.
6. The TurboBrush™ Tool bracket slides into
the front of the handle. Attach the bracket by aligning the pegs with the holes on
the handle and pulling down until it locks
into place.
7. Place the TurboBrush™ Tool in the bracket by
aligning the bottom of the bracket with
the opening of the brush roll and snap the
TurboBrush™ Tool into place.
www.bissell.com
5
Operations
Handle position
Press the handle release pedal with
your foot to place your BISSELL
Cleanview Pet Plus into one of three
cleaning positions.
1.Upright- For storage and above floor
cleaning with special tools.
2. Normal Cleaning- Press handle release
pedal once. Use for most household floor
cleaning tasks.
3. Low Cleaning- With the vacuum in
normal cleaning position, press handle
release pedal again. Use for reaching
under low furniture such as tables, chairs
and beds.
Powerfoot height adjustment
The powerfoot/rotating floor brush
on your BISSELL Cleanview Pet Plus can
be adjusted to clean several floor surfaces.
NOTE: For optimal cleaning
performance, adjust to the lowest
practical setting. If your cleaner is
difficult to push, adjust to the next
higher setting.
1. Place handle in upright position.
2. Turn height adjustment knob to desired setting.
Lowest Setting - For bare floors.
Medium Settings - For short and medium
pile carpets.
Highest Setting - For plush pile carpets.
3. Place the handle into the normal cleaning
position and the powerfoot will adjust to
the setting chosen.
1
2
3
caution:
Before using your vacuum, make sure
that the dirt container is in locked
position and that all filters (inner circular,
outer circular, pre-motor and postmotor) are in place. Do not operate
your vacuum without these filters.
ATTENTION:
Some Berber carpets have a tendency to
fuzz with wear. Repeated strokes in the
same area may aggravate this condition.
Consider setting your cleaner on a higher
than normal setting for this type of carpet.
Tip:
Before cleaning
under low furniture, check area
first for objects
that might harm
the unit or block
the vacuum hose.
NOTE: You may also adjust the
setting while in the normal cleaning
position.
Tip:
Transporting cleaner
1. To move your cleaner from room to room,
put the handle in the upright position, tilt the
cleaner back on its rear wheels and push
forward.
2. The cleaner can also be moved by using
the carrying handle on the back.
Carrying
Handle
6
www.bissell.com
Your vacuum
features a Quick
Release cord
wrap. To remove
the power cord
quickly and easily, rotate the
upper cord wrap
towards the floor,
and slip power
cord from upper
and lower
cord wraps.
Operations
Special tools
Your BISSELL Cleanview Pet Plus is not
only a powerful carpet and rug vacuum
cleaner, it’s also a versatile above floor
vacuum cleaner when you select one of
the special tools.
1. Raise handle to upright position.
2. Grasp the Quick Reach handle and lift hose
wand to separate from suction intake opening.
3. Attach tools by firmly pushing onto
vacuum hose or extension wand.
Combination Dusting Brush/Upholstery
Tool:
Two types of cleaning tools are included
in one attachment; rotate for desired tool.
NOTICE:
The floor brush will continue to rotate while
you use your vacuum for above floor
cleaning. To prevent carpet damage, do
not lean on the vacuum or let the powerfoot tilt forward.
Tip:
Hair, string and
small objects
can block the
vacuum hose or
tools. Check them
occasionally for
obstructions.
■Use brush side to dust furniture, blinds,
books, lamps, shelves and baseboards.
■Use upholstery side for curtains, draper
ies, cushions and fabrics.
Crevice Tool: Use in tight, narrow spaces.
Extension Wand: Use with desired
attachment for a longer reach.
TurboBrush™ Tool: Use rotating brush
action for small areas such as stairs and
upholstery.
NOTE: Press gently when using the
TurboBrush™ Tool to gain maximum
cleaning. Too much pressure will
cause the brush to stop rotating.
Power cord
When you are done using your
BISSELL Cleanview Pet Plus, return it
to the upright position and store the
power cord.
1. Turn power switch OFF.
2. Unplug power cord by grasping the plug
(NOT the cord) and disconnect from outlet.
3. Loop power cord around cord wraps on
side of vacuum cleaner.
CAUTION:
The rotating floor brush continues
to rotate while tools are in use. To
reduce the risk of injury from moving parts, always move the cleaner
with the carrying handle at the
back of the cleaner. Always place
the vacuum cleaner on the floor
with the handle in upright position
when using tools. Never place your
fingers under the cleaner when it is
running. Never place powerfoot on
furniture or uneven surfaces. Do not
place vacuum cleaner close enough
to objects to pull them into rotating
brush.
NOTICE:
While vacuuming, certain carpets and low
4. Clip molded plug to power cord to secure. humidity conditions may generate small
static discharges. The discharges are entirely
harmless and are not associated in any way
with the main power supply.
www.bissell.com
7
Maintenance and care
To maintain maximum cleaning
performance from your BISSELL
Cleanview Pet Plus, perform these
simple maintenance steps.
1. Empty the dirt container when the dirt
reaches the “Full” line on the side.
2. Check the inner and outer circular
filters, and the pre-motor filter at least
once a month and clean or replace as
needed.
WARNING:
To reduce the risk of electric shock, turn
power switch OFF and disconnect plug
from electrical outlet before performing
maintenance or troubleshooting checks.
Tip:
3. Replace the HEPA media post-motor
filter* every three to six months.
For maximum cleaning
performance, check
and clean or replace
all filters as suggested.
Note: More frequent filter cleaning
or replacing may be necessary if
you are vacuuming new carpet,
fine dust, or have allergy concerns.
Follow the instructions on the following pages to perform these
simple maintenance steps.
Emptying dirt container
The dirt container needs to be emptied
when the dirt reaches the “Full” line
on the side of the container.
1. Unplug cleaner from electrical outlet.
2. Slide the Lock ‘n Seal lever to the
"Unlock" position.
Full Line
Unlock
Position
3. Grasp handle and pull dirt container
straight out to remove from vacuum.
4. Empty dirt into garbage container.
5. Put dirt container back in the vacuum
and slide the lever to the "Lock"
position.
Note: The dirt container may be
washed in warm water with a mild
detergent. Remove the filter cup from
the bottom before washing. Make
sure it is completely dry before
reassembling with the filter cup.
* The filter media, not the vacuum as a whole, complies
with the IEST-RP-CC001.5 HEPA Standard
8
www.bissell.com
Lock Position
Maintenance and care
Cleaning the inner & outer circular filters
1. Unplug cleaner from electrical outlet.
2. Remove the dirt container as described
in the previous section. Grasp the filter
cup located at the bottom of the dirt
container and twist counterclockwise to
unlock and remove.
NOTICE:
This product is intended for household use
only and not for commercial or industrial
use. Vacuuming of dust from products like
plaster, concrete or ashes will damage the
motor and void the warranty.
3. Grasp the circular filters and pull
straight up to remove.
4. Separate the outer foam and inner
pleated circular filters. Wash each individually by hand in warm water. Mild
detergent may be used if desired. Rinse
well, then air dry
thoroughly before putting them back
together and replacing in filter cup.
5. The filter cup may be washed in warm
water with a mild detergent. Make sure it
is completely dry before reassembling with
filters.
6. The upper tank and primary separator
may be wiped clean with a damp cloth.
Reach underneath the upper tank and
turn the rim of the primary separator to
unlock. Pull straight down to remove.
Cleaning the pre-motor filter
1. Unplug the cleaner from electrical outlet.
2. The pre-motor filter protects the motor
from debris. It is located underneath the
dirt container and filter cup in the center
of the round part of the Lock ‘n Seal
lever.
WARNING:
Do not operate cleaner with
damp or wet filters or without
all filters in place.
3. Remove the small, round, pre-motor filter
and any debris on top of it. Rinse well
under warm water, then air dry thoroughly
before replacing.
Pre-Motor
Filter
www.bissell.com
9
Maintenance and care
Replacing the HEPA media post-motor filter*
The post-motor filter is a HEPA media
filter*, which assists in the filtration
process to return clean air to the room.
1. Unplug the vacuum from electrical outlet.
2. Remove the filter door, located on the
front of the vacuum.
3. Remove the post motor filter.
HEPA
Media
Post-Motor
Filter*
4. Replace the post-motor filter with a new
filter.
NOTE: The post-motor filter is a
white pleated HEPA media filter*.
This filter is NOT washable and must
be replaced when it becomes dirty.
5. Replace the door by inserting the tabs on
the left side and snapping the right side into
place.
Maintaining the TurboBrush™ Tool
The TurboBrush™ Tool should be checked
regularly for clogs or debris wrapping
around the brush roll.
1. Remove TurboBrush™ Toolfrom hose or
front of vacuum.
2. Twist collar so opening is at the top and lift
top cover to remove.
3. Remove brush from belt and clean debris.
4. Replace brush inside belt and place ends
into slots on sides.
5. Reposition top cover, making sure to
line up the inside tab at the front with
the opening on the cover. Twist collar
until opening is at the bottom to lock into
place.
* The filter media, not the vacuum as a whole, complies
with the IEST-RP-CC001.5 HEPA Standard
10
www.bissell.com
WARNING:
To reduce the risk of injury
from moving parts, turn the
power switch OFF and
disconnect plug from electrical
outlet.
Maintenance and care
Check rotating floor brush and drive belt
You should check your vacuum cleaner’s
rotating floor brush and drive belt regularly for wear or damage. You should
also clean the brush and brush ends of
string, hair and carpet fibers. These can
wrap around the brush and hamper its
ability to effectively clean your carpet.
Also remove any debris that has accumulated under the brush cover.
1. Unplug cleaner from electrical outlet.
Brush
Cover
2. Place handle in low position and turn
vacuum cleaner over so bottom side is up.
3. Remove the two screws from the brush
cover (as shown) with a Phillips head
screwdriver. Lift the brush cover off.
4. Grasp rotating floor brush at both ends
and lift.
5. Clean strings, hair and other debris
from rotating floor brush, paying particular attention to brush ends.
6. Clean strings, hair and other debris from
motor pulley and drive belt areas.
7. Check drive belt carefully for wear, cuts
or stressed areas. Replace if worn or
damaged.
8. Check air passageway for obstructions.
Remove debris from this area.
Motor
Pulley
Air Passageway
Replace drive belt
1. Unplug cleaner from electrical outlet.
2. With rotating floor brush removed from vacuum cleaner (Steps 1-4 of "Check rotating
floor brush and drive belt"), grasp old drive
belt and remove from motor pulley. Discard
old drive belt.
3. Place new drive belt over motor pulley
and stretch other end over rotating floor
brush in the space between the bristles.
4. Place ends of rotating floor brush down
into slots on sides as shown.
5. Turn rotating floor brush by hand several
times in direction of motor pulley. If properly installed, drive belt will center itself on
rotating brush.
6. Reposition brush cover and replace two
screws. Make sure end of brush cover is
snapped into place.
www.bissell.com
Brush
Cover
11
Maintenance and care
Replace light bulb
1. Unplug cleaner from electrical outlet.
2. Using a flat screwdriver, table knife or
coin, insert into the slot on the right of
the lens and gently push inner latch to
the left, as shown, to remove the lens.
3. Remove the bulb from the socket by grasping bulb and pulling straight out. Install
the new bulb by pushing it gently into the
socket until the bulb snaps into place.
4. Reposition lens by inserting tab on left side
and then pushing the right side back into
place.
Clearing clog
Low suction, poor pickup or no suction
may be due to a clog in the vacuum
cleaner. If you notice a change in
the sound of the vacuum motor or a
reduction in the spinning action in the
dirt container, check for clogs.
1. Unplug cleaner from electrical outlet.
FPO
Primary
Separator
2. Empty dirt container.
3. Check upper tank and primary separator for build up or clogs. Check to make
sure primary separator is installed correctly. To unlock the primary separator,
grasp the rim and turn toward the left.
Pull straight down to remove. If the primary separator is missing or not locked
into place, check and clear the tube in
the center of the dirt container and properly install primary separator.
4. Remove the Twist ‘n Snap hose from the
vacuum by turning to the left. Check the
suction inlet, hose and hose wand for
clogs. Remove any clogs from the hose
using a long, narrow object such as a
broomstick.
Suction
Inlet
Hose Wand
Base
5. Check the foot hose for clogs. If needed, remove the screw attaching the hose
wand base to the vacuum. Straighten
the foot hose and unclog with a long,
narrow object such as a broomstick.
6. If the clog persists, follow the instructions
for checking the rotating floor brush on
page 11 and inspect the air passageway
for obstructions.
12
www.bissell.com
Air Passageway
Troubleshooting
Vacuum cleaner won’t turn
Possible causes
1. Power cord not firmly plugged in
WARNING:
To reduce the risk of electric
shock, turn power OFF and disconnect plug from electrical
outlet before performing
maintenance or troubleshooting.
Remedies
1. Check electrical plug
Vacuum cleaner won't pick up dirt
Possible causes 1. Incorrect height adjustment
Remedies
1. Adjust powerfoot to correct height setting
2. Hose not attached to suction opening
2. Grasp Quick Release handle and firmly push
hose wand onto the suction opening.
3. Twist 'n Snap hose not securely attached
3. Make sure Twist 'n Snap hose is snapped
into locked position
4. Crack or hole in hose
4. Check hose and replace if needed
5. Broken or worn drive belt
5. Replace drive belt, see page 11
6. Rotating floor brush bristles worn
6. Replace brush
7. Rotating floor brush jammed
7. Remove brush and clean debris from brush ends
8. Clog in vacuum
8. Follow instructions for clearing clogs on page 12
9. Dirt container full
9. Empty dirt container
10. Dirt container not installed properly
10. Position correctly and lock in place
11. Filters are dirty
11. Check and clean inner and outer circular filters and ,
pre-motor filter, replace post-motor filter
12. Primary separator missing or installed incorrectly
12. Check for a clog in the tube in the center of the dirt
container, clear and properly install primary separator
13. TurboBrush™ Tool is clogged or debris is wrapped
around the brush
13. Maintain TurboBrush™ Tool, see page 10
Tools won't pick up dirt
Possible causes
Remedies
1. Crack or hole in hose
1. Check hose and replace if needed
2. Vacuum hose, wand or tools clogged
2. Follow instructions for clearing clogs on page 12
3. Dirt container full
3. Empty dirt container
4. Dirt container or upper tank not installed properly
4. Position correctly and lock in place
5. Filters are dirty
5. Check and clean inner and outer circular filters and ,
pre-motor filter, replace post-motor filter
6. Primary separator missing or installed incorrectly
6. Check for a clog in the tube in the center of the dirt
container, clear and properly install primary separator
Vacuum cleaner difficult to push
Possible causes 1. Incorrect height adjustment
Visible dirt escaping from cleaner
Possible causes 1. Dirt container full
Remedies
1. Adjust powerfoot to correct height setting
Remedies
1. Empty dirt container
2. Filters missing or installed incorrectly
2. Check inner and outer circular filter and post-motor
filter for correct installation
www.bissell.com
13
Troubleshooting
Visible dirt escaping from cleaner continued
Possible causes Remedies
3. Dirt container installed incorrectly
3. Position correctly and lock into place
4. Filter cup installed incorrectly
4. Remove dirt container and make sure filter
cup is fully attached
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
Replacement parts Item
1
2
3
4
5
6
7
8
9
10
11
12
13
Part No.
32074
203-1297
203-1056
203-1059
203-1068
203-1216
203-5624
32064
32065
3205
203-1215
203-7170
203-7196
Part Name
Style 7/9/10/12/14 Drive Belt (2-Pack)
Standard Headlight Bulb
Crevice Tool
Combination Dusting Brush/Upholstery Tool
Extension Wand
Wire Reinforced Twist ‘n Snap Vacuum Hose (Select Models Only)
Wide Brush Roll
Style 9/10/12 Inner & Outer Circular Filter Set
Style 9/10/12 Inner Circular Filter only
Style 12 HEPA Media Filter*
Pre-Motor Filter
TurboBrush™ Tool Bracket
TurboBrush™ Tool
1
2
3
4
5
6
7
8
9
10
11
12
13
* The filter media, not the vacuum as a whole,
complies with the IEST-RP-CC001.5 HEPA Standard
14
www.bissell.com
Warranty - BISSELL CleanView™ Pet Plus Cyclonic
This warranty gives you specific legal rights, and you may also have other rights which may
vary from country to country. If you need additional instruction regarding this warranty or have
questions regarding what it may cover, please contact BISSELL Consumer Services by
telephone, or regular post as described below, or contact your local in country distributor.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc.,
will replace (with new or remanufactured components), at BISSELL’s option, free of charge
from the date of purchase by the original purchaser, for one year any defective or
malfunctioning part do to manufacturers defect.
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters, belts, or
brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair
or any other use not in accordance with the User's Guide is not covered.
For UK inquiries:
Monday - Thursday 9 am — 5 pm
Friday
9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough
Berkshire, SL1 4QT
United Kingdom
Telephone: 0844-888-6644
For spare parts and accessories:
Monday - Friday 9 am — 5:30 pm
Exserve Ltd.
550, Peterborough
Cambridgeshire, PE2 6WH
Telephone: 01733-362415
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT.
BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
www.bissell.com
15
BISSELL consumer services
If your BISSELL product should require service:
Call BISSELL Consumer Services at the numbers below and we will give you the location of a
BISSELL Authorized Service Center in your area. For all other countries, contact your local in
country distributor for questions, service, or repair.
If you have questions about your warranty or need replacement parts please contact the
numbers below.
For UK inquiries:
Monday - Thursday 9 am — 5 pm
Friday
9 am — 4 pm
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough
Berkshire, SL1 4QT
United Kingdom
Telephone: 0844-888-6644
For spare parts and accessories:
Monday - Friday 9 am — 5:30 pm
Exserve Ltd.
550, Peterborough
Cambridgeshire, PE2 6WH
Telephone: 01733-362415
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It
provides proof of purchase date in the event of a
warranty claim. See Warranty on page 15 for details.
16
©2011 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 110-4469
Rev 9/11
Visit our website at:
www.bissell.com
www.bissell.com
Download PDF

advertising