PE 9038-m
Fully automatic espresso coffee machine
Operating and Installation Instructions
ENGLISH
CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
2/35
Safety instructions
Description of the coffee machine
Description of the control panel: touch control
Instructions for the first use of the machine
Making Coffee
Hot water
Steam
Programming the amount of coffee beans to be grinded
Programming the volume of coffee dispended in the cup
If you wish to reset the standard values
Signals and alarms
Coffee menus
Cleaning
Installation
Something not working....
Technical specifications
After-sales Service, spare parts and guarantee
1. SAFETY INSTRUCTION
Please read this instruction book before using the appliance and retain for
future reference. These warnings are provided in the interests of your safety,
ensure you understand them fully before using the appliance.
Intended use
•
•
The appliance is intended for use in the home. If the appliance is used for
purposes other than those intended or used incorrectly, no liability can be
accepted by the manufacturer for any damage or injury that may be caused.
Alterations or changes to the appliance are not permitted for reasons of
safety.
Prior to initial start-up
•
Check the appliance for transport damage. Under no circumstance should
a damaged appliance be plugged in! In the event of damage, please contact your retailer.
Safety of children
•
•
Keep packaging material away from children. Risk of suffocation!
Please make old appliances unusable prior to disposal. Pull out the mains
plug, and cut off the mains cable.
DURING USE
CAUTION:
The filtering unit will always be kept very hot to obtain an excellent coffee.
Therefore please empty the “used” coffee tank with extreme care to avoid
being scalded.
•
•
•
•
•
•
This machine must be used only by adults. Make sure that children cannot
touch the controls nor play with the machine.
Modifying or merely trying to modify the characteristics of this product is very
dangerous, and will invalidate your guarantee.
Always keep this machine clean.
The external parts of this machine become very hot while it is operating
and they will not cool down immediately after the machine is switched
off. Keep children out of reach.
Before cleaning or servicing the machine, make sure that it is
disconnected from the power supply.
In case of malfunction, never try to repair the machine yourself. Consult this
manual and if the necessary information cannot be found, please contact the
nearest Service Force Centre. This machine must be serviced exclusively by an
authorised Service Force Centre. Always ensure the use of genuine spare parts.
3/35
FOR INSTALLATION AND SERVICING
Keep this instruction manual together with the machine for any future
reference. If the machine is sold or transferred to another person, make sure
that this instruction manual is given to the new user, so that he/she can
become familiar with the machine’s functions and with the
recommendations given.
•
•
•
This machine must be installed and connected to the mains by a
COMPETENT PERSON. Make sure that the machine is DISCONNECTED
from the power supply before any servicing operation.
After unpacking the machine make sure that the product has not suffered any
damage and that the power cord is in perfect condition. In case of damage, please
contact your retailer or our customer service dept.
The Manufacturer declines all responsibility if the safety rules are not
complied with.
SOME HINTS OF ENVIRONMENTAL PROTECTION
PACKAGE
•
All the packing materials are environmentally friendly and they can be recycled.
Please help in preserving the environment, by using the proper channels of
separate collection of rubbish.
DISPOSAL
Appliance Packaging Information
All materials are environmentally sound.
The plastics can be recycled and are identifìed as follows:
>PE< for polyethylene, e.g. the outer covering and the bags in the interior.
>PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluorocarbon.
The carton parts are made from recycled paper and should be disposed of at a wastepaper recycling collection location.
Disposal of Old Appliances
• Use an authorised disposal site.
Contact your Local Council or Environmental Health Office to see if there
are facilities in your area to recycle the appliance.
on the product or on its packaging indicates that this product may
The symbol
not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about
recycling of this product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product
4/35
CE
This machine complies with the directive BT 73/23
Electrical safety rules EN 60335-1 (August 1995 - Safety for electrical household and
similar appliances – General Standard) and EN 60335-2-15 (April 1996 – Specific Rules
concerning the equipment for heating liquids).
Directive EMC 89/336 in conformity with the following standards:
55014-1; 55014-2; 61000-3-2; 61000-3-3
ELECTRICAL CONNECTION
Any electrical work required to install this appliance should be carried out by a qualified
electrician or competent person.
WARNING: THIS APPLIANCE MUST BE EARTHED.
Should the appliance power supply cable need to be replaced, this must be carried out
by a Service Force agent. The manufacturer declines any liability should this safety
measure not be observed.
Before switching on, make sure the electricity supply voltage is the same as that
indicated on the appliance’s rating plate.
The appliance should be fitted with a 13amp plug. The plug should be fitted with a
13amp ASTA approved BS1363/A fuse. The mains lead of the appliance should be
connected as described below. The wires in the mains lead are coloured in accordance
with the following code:
•
Green and Yellow - Earth
•
Blue - Neutral
•
Brown - Live
In the plug the colours of the wires may not correspond with the markings identified
with the terminals in your plug:
1) Connect the Green and Yellow (earth) wire to the terminal in the plug which is
marked with the letter "E" or the earth symbol or coloured green and yellow.
2) Connect the Blue (neutral) wire to the terminal in the plug which is marked
with the letter "N" or coloured black.
3) Connect the Brown (live) wire to the terminal in the plug which is marked with
the letter "L" or coloured red.
4) Upon completion there must be no cut, or stray strands of wire present and
the cord clamp must be secure over the outer sheath.
5/35
THE PLUG MUST STILL BE ACCESSIBLE AFTER THE APPLIANCE HAS
BEEN INSTALLED.
THE APPLIANCE SHOULD NOT BE CONNECTED TO THE ELECTRICAL
SUPPLY BY MEANS OF AN EXTENSION CABLE
PERMANENT CONNECTION
In the case of permanent connection it is necessary that you install a double pole
switch between the appliance and the electricity supply (mains), with a minimum gap
of 3mm between the switch contacts and of a type suitable for the required load in
compliance with the current electrical regulations.
The switch must not break the yellow and green earth cable at any point.
6/35
2. DESCRIPTION OF THE COFFEE MACHINE
1.
2.
3.
4.
5.
6.
7.
8.
9.
Water reservoir
Brita filter
Coffee Outlet
Steam/water nozzle
Drip tray
Coffee beans container
Grinding regulation knob
Control panel
“Used” coffee drawer
7/35
3. DESCRIPTION OF THE CONTROL PANEL:
TOUCH CONTROLS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Water refill indicator
ON-OFF/stand-by indicator
Start indicator
Hot water selector indicator
Steam selector indicator
Light selector indicator
Espresso coffee indicator
Regular coffee indicator
Used Coffee 'drawer full' indicator
ON-OFF/stand-by control
Start control
Hot water selector control
Steam selector control
Light selector control
Espresso coffee control
Regular coffee control
TOUCH CONTROLS: Instructions for use
These touch controls must be pressed precisely to prevent functions from being
enabled accidentally. Pressing lightly on the respective symbol will enable the
corresponding function.
8/35
4 INSTRUCTIONS FOR THE FIRST USE OF THE MACHINE
FILLING UP THE WATER
RESERVOIR
•
Squeeze together the
unlocking levers found
under the drip tray
•
Gently pull the coffee machine
forward from the housing by
sliding it along the telescopic
runners.
9/35
Hardness of water:
•
Before filling up the water reservoir, make
sure that the decalcifying Brita filter has
been soaked in cold water for at least 30
min. Follow the instructions printed on the
filter package. After this operation insert the
filter into position inside the water reservoir
as shown in the figure.
•
If the machine will not be used for long
periods, empty the water from tank.
•
Brita filters are available from most
supermarkets and domestic goods outlets, at
our After-Sales Service Centres or at the
Shops of Authorized Spare Parts.
•
Remove the reservoir and fill it with
approximately 2.5 litres of water as shown.
•
replace the water reservoir in its own
housing taking care to fully engage the
water valve into the docking station.
10/35
•
Ensure the mains ON/OFF
switch(at rear) is ON
•
push the machine back into the
housing until a “CLICK” can be
heard. This indicate that the
machine has been locked in
position.
FILLING UP THE CONTAINER WITH COFFEE BEANS
•
Press the unlocking levers located
under the drip tray and pull the
machine as it is shown in the
figure.
•
pull the coffee machine forward
from the housing along the
telescopic runners .
11/35
•
Pour approximately 200g of coffee
beans into the container on the top as
shown in the figure.
•
Push the machine back into the
housing until a “CLICK” can be heard.
This indicate that the machine has
been locked in position.
INITIAL START-UP
•
•
Put the main switch in position 1
The led corresponding to the ON-OFF
control will blink rapidly for 3 minutes.
12/35
•
•
The machine is be in stand-by mode when the ON-OFF LED is blinking slowly,
it is then ready to be switched on.
•
Ensuring the water reservoir and the coffee beans container are full, switch
the coffee machine on by pressing the on-off control and the corresponding
LED stops flashing and remains lit.
ADJUSTING THE TEXTURE GROUND COFFEE
CAUTION
•
This machine is calibrated in the factory for an optimum level of ground
coffee. Too “coarse” ground coffee will result in a weaker coffee. Too “fine”
ground coffee will result in very strong coffee, delivered by “drops” and tasting
“bitter”.
The time required for an espresso will
range from 20-30 seconds.
•
Press the unlocking levers located
under the drip tray and pull the machine
as shown in the figure.
13/35
•
Pull the coffee machine forward
from it’s housing by sliding it
along it’s telescopic runners.
•
Turning the knob will adjust the
coffee texture. Before adjusting,
make a note of the original
setting so that the machine
can be reset, if required, to the
factory settings. Turning the
knob in the clockwise direction
will lead to a fine texture for a
stronger coffee. Turning the
knob anti-clockwise will lead to
a coarse texture for a weaker
coffee. The set grinding level
can be read on the lid of the
coffee case: bigger circles
means “coarse” grinding level
(fast-flowing weak coffee),
whereas smaller circles means
“fine” grinding level (slowflowing strong coffee).
•
Push the machine back into the
housing until a “click” can be
heard. This indicates that the
machine is locked in position.
14/35
STAND-BY MODE
•
Once powered and inserted into the cabinet, the machine is in stand-by mode: this
will be signaled by the on/off LED blinking.
•
Press the on/off control to switch on the machine: the start LED will be illuminated.
•
To come back to the stand-by mode, press the on/off control once again.
CAUTION:
On start-up, the machine initiates the pre-warming phase for the first 3
minutes. During this phase the ON/OFF LED will blink quickly and the
machine will be not able to execute any operation. Then the LED blinks
slowly and the machine is ready to operate.
15/35
5
MAKING COFFEE
•
Press the control corresponding to the desired selection.
•
Press the start control within 10 seconds and the machine will make the coffee
selected.
The machine will stop automatically
•
CAUTION: the desired function will be disabled if the start control is not pressed
within 10 seconds. It will then be necessary to repeat the procedure.
HOW TO OBTAIN AN EXCELLENT ESPRESSO
•
The brewing time for an excellent espresso will be about 15 - 25 seconds.
Elements affecting this brewing time are the grinding level of the coffee and the
quantity of ground coffee. If necessary, the grinding level, as well as the quantity
of ground coffee can be modified (refer to Chapters 8 & 9. Instructions for the first
use of the machine).
Useful advice: coffee is a hygroscopic element that is its quality and characteristics
strictly depend on weather (humidity). Coffee should be ground coarser if humidity in
the air is very high, otherwise it will become thick and not flow freely; on the contrary,
the coffee should be ground finer in dry conditions.
16/35
6
HOT WATER
•
The steam/water pipe can be moved to the back of the cabinet when not in use.
Pull forward when required.
Do not touch when HOT!
•
To dispense hot water, place a container under the steam/water nozzle; then
press the water control.
•
Press and hold the start control within 10 seconds until the desired amount is
dispensed. To stop the water flowing, simply release the control.
CAUTION: the desired function will be disabled if the start control is not
pressed within 10 seconds. It will then be necessary to repeat the procedure.
17/35
7
STEAM
•
Press the steam control and the corresponding indicator blinks for 20 seconds.
The machine will be ready to make steam when the indicator stops blinking and
remains lit.
•
•
Place a jug with the liquid to be heated under the steam nozzle.
Press and hold the start control within 10 seconds and wait for the steam function
to commence.
HEATING LIQUIDS
CAUTION: the desired function will be disabled if the start control is not pressed
within 10 seconds. It will then be necessary to repeat the procedure.
•
The steam will continue to spray till the start control is released.
MILK FOR CAPPUCCINO: Pour some cold milk (100cc min.) in a deep jug and
heat it using steam. Agitate the milk jug a little and wait until the foam is
ready (one minute min.). To improve the result, gently beat the jug a little on
the table after that the foam is ready.
18/35
8
PROGRAMMING THE AMOUNT OF COFFEE BEANS TO BE
GRINDED
•
•
This espresso machine has already been calibrated in factory to dispense the
ideal measure of ground coffee for one cup of espresso.
However this quantity of ground coffee can be increased or reduced, then the
selected measure is stored. The programmable measure of ground coffee
refers to both the espresso selection and to regular coffee selection.
Put the machine on stand-by mode as described.
•
Keep the start control pressed for 10 seconds.
•
Some LEDS will flash, working as indicators, (the more the LEDS are
illuminated the greater the quantity of coffee). Before adjusting make a note
of the original setting so that the machine can be reset to the factory settings
if required.
•
To increase or decrease the quantity of ground coffee just press the
“espresso” control to decrease and “regular coffee” control to increase.
•
19/35
•
Once you have modified the coffee ground quantity, press the start control for 10
seconds and the machine will automatically save the quantity desired and it will
return to stand-by mode.
CAUTION: the correct grinding time can change if a different
kind of coffee is used.
If any unpressed coffee powder is found when emptying the “used”
coffee drawer, it means that the grinding time is too long and should be
decreased.
The “exhaust” coffee pods in the “used” coffee drawer can help to
achieve a correct regulation of the grinding-time.
The coffee pods must be 1 cm in thickness: this is the correct coffee
quantity.
If its thickness is lower, it means that the grinding time is too short and
should be increased.
IMPORTANT: Increasing or decreasing the grinding time can
change the coffee taste.
A stronger coffee taste and a rich aroma can be obtained by slightly
increasing the programmed time.
A weaker coffee can be obtained by slightly decreasing the programmed
time.
20/35
9
•
•
PROGRAMMING THE VOLUME OF COFFEE DISPENSED IN
THE CUP
The volume of coffee dispensed can be adjusted as desired as follows:
Press the espresso control.
•
Keep the start control pressed until the programme starts (approximately 5
seconds); the start control LED flashes.
•
When the desired quantity of coffee has been dispensed, press the start control.
The machine will stop the cycle and the coffee measure will be stored
automatically on the correspondent selection.
21/35
10
IF YOU WISH TO RESET THE STANDARD VALUES
RESETTING STANDARD VALUES
•
This coffee machine is calibrated in the factory to make the optimum Italian
espresso, the values set for the espresso coffee distribute 30 cc, the values set for
the regular coffee is 80 cc.
•
if the standard values have to be reset from the stand-by control switch on the
machine then press both the on/off and hot-water controls at the same time for 5
seconds.
•
All the LEDs will briefly illuminate to indicate the factory values have been reset.
•
Press the ON/OFF control. Each selection will use the factory values.
N.B.: Only the quantity of water required for each cup of coffee is reset. The
measures of ground coffee will not alter.
22/35
11
SIGNAL AND ALARMS
WATER REFILL INDICATOR
•
This machine has a sensor which detects when the water reservoir is empty.
the reservoir empty led will illuminate. The machine will not operate until the
water reservoir is refilled.
VOLUMETER COUNTER FAULT
•
This machine has a volumeter counter which detects the amount of water
distributed by the machine. If the water reservoir is empty or if the volumeter
counter is faulty the reservoir empty led will blink and the machine will not
operate.
To reset this alarm, please put the machine in stand by mode then turn it on again
“USED COFFEE DRAWER FULL”/ COFFEE BEENS REFILL INDICATOR
•
•
•
Every 20 coffee the machine shows you that the coffee beans container is empty
and that the “used coffee drawer” is full.
When the corresponding led will be illuminated, you must empty the Drip tray
and the “used coffee drawer” and refill the coffee beans container.
For instructions on how to empty the “used” coffee drawer, see chapter 13
“CLEANING”.
23/35
FAULT INDICATOR
•
The machine incorporates an automatic system that, detecting a fault in operation,
will illuminate all the LEDS. Switch OFF the machine and contact the nearest
Service Force Centre.
12
COFFEE MENUS
ITALIAN CAPPUCCINO
This is a normal espresso with steam-heated milk giving the coffee a milder flavour and
a rich, delicious frothy topping. Serve in a large cup.
Pour some cold milk into a deep jug and heat using the steam jet. Pour only the froth
onto the espresso, tilting and rocking the jug slightly or scoop off the froth with a
spoon.
Some cocoa powder can also be dusted on the milk froth.
VIENNESE CAPPUCCINO
This variation is the result of the age-old Austrian tradition.
Prepare a 'weak' espresso on the machine for 30-35 seconds, then add hot milk topped
by whipped cream. Serve in a medium-sized cup (midway between an espresso cup
and a cappuccino cup).
Decorate with flakes of chocolate.
COLD ESPRESSO SHAKE
Frothy and extremely refreshing, this drink is delicious on hot days.
Prepare an espresso, add sugar and pour into a shaker with large ice cubes. Shake for
few seconds. Serve in a tumbler or flûte.
IRISH COFFEE
Energy-giving and invigorating drink.
Warm a long glass and mix eight parts of hot coffee with one part whisky and brown
sugar.
Gently pour some freshly whipped cream over the back of a spoon so that it floats on
the coffee: the result is a layer of cool white cream on top of the hot dark coffee.
24/35
13
CLEANING
OUTER PARTS
•
Clean the stainless steel parts of
the machine with a soft cloth
without using aggressive
detergents. Never use any abrasive
sponges nor steel wool to clean the
parts of steel. Dry well with a soft
cloth.
STEAM NOZZLE
•
Remember to clean the steam nozzle periodically as it can get internally dirty when
frothing the milk. Remove the nozzle as shown in figure above and wipe it,
together with its cap, using a sponge and hot water.
Caution: to clean the nozzle, switch OFF the machine and wait 20
minutes after use to allow it to cool, to prevent risks of burns.
25/35
DRIP TRAY
•
•
Remove the drip tray from the machine as it is shown in the figures above.
Make sure that the drip tray is periodically drained to prevent any liquid from
seeping out and dirtying/damaging the underlying furniture. Drip tray and relevant
grill can be washed in a dishwasher.
TO EMPTY THE “USED” COFFEE DRAWER
It is necessary to remove the drip tray as
it is shown in the figure, and drain it.
26/35
Pull open the door and remove the drawer
and empty it.
The drawer can be washed in a
dishwasher or simply with hot water.
Replace the drawer and close the door.
Replace the drip tray.
27/35
WATER RESERVOIR
•
•
•
•
If the machine is not used for long periods, change the water in the reservoir and
drain the boiler by pressing the coffee button several times.
Clean the water reservoir periodically .
The water reservoir can be washed in a dishwasher.
When using the Brita filter, replace it after approximately 2000 cups of coffee or at
least every three months.
CLEANING CYCLE OF THE BOILER
•
•
•
•
•
This coffee machine is an appliance using water, therefore it is normal that some
limescale can form in its boiler.
It is recommended to carry out the following operations every six months:
Fill up the water reservoir with 2 litres of water adding half a glass of vinegar or
citric acid.
Carry out the same operations as preparing some cups of coffee (refer to the
previous Chapter “Coffee”), and some cups of hot water until the reservoir is
completely empty.
Fill the reservoir again with cold water and repeat the above process to rinse the
boiler.
28/35
14
INSTALLATION
BUILDING-IN
Installing the machine into kitchen furniture with proper characteristics will ensure a
correct operation of the equipment.
Complying with the safety rules, ensure a proper protection against any contact with
the electric components and with the parts protected only by functional insulation, by
housing the machine correctly into the furniture.
All components that guarantee protection, even a cover panel (for instance, when the
machine is positioned at one of the ends of the modular furniture), should be firmly
fixed so that they cannot be removed without tools.
Install this machine at a certain distance from refrigerators or freezers, because the
heat it emits can impair their functioning.
COMPONENTS FOR INSTALLING THE MACHINE
This coffee machine and drawer can be installed into cabinets with height of 450 mm
and width ranging from 560 mm to 570 mm. The machine is equipped with the
following components for the installation:
1.
2.
3.
4.
5.
6.
1 fixing base
9 self-threading screws
3.9X19
1 cable clamp
2 side slides
2 side-plates of 1 mm
4 side-plates of 2 mm
29/35
ELECTRICAL CONNECTION
•
Fix the power cable onto the left
side of the cabinet using one of the
self-threading screws of the
equipment and the proper cable
clamp as shown in the figure.
•
Unscrew the cable clamp available on the
machine.
•
Fix the power cable onto the machine as
shown in the figure.
30/35
•
Connect the power cable as shown in
the figure. This machine is designed for
a single phase voltage of 230V. The
power supply requires only outlets of
13A fuse and a double pole isolation
switch with at least 3 mm between
contacts.
INSTALLING THE MACHINE
•
Lay the U base plate of the machine
on the shelf of the cabinet.
•
Ιnsert
the
L
plates,
compensating for any space. The
width of the housing unit the coffee
machine depends on the thickness of
the cabinet’s sides. six side plates
(four being 2 mm thick and two 1 mm
thick) are provided to compensate for
the different possible measures.
31/35
•
Τhey should be used
to compensate for the internal
width of the compartment,
leading to a width of 560/570
mm.
•
Fix the U base plate inserting 4 selfthreading screws into the 4 front holes
of the same plate. Then screw the
telescopic runners to each side with the
remaining 8 self-threading screw.
•
Insert the machine into the
housing by coupling the machine
to the runners fixed to the sides
of the carcass.
32/35
•
Slide the machine into the cabinet until
the “click” indicates that it is locked into
Position.
15
SOMETHING NOT WORKING.....
If this machine does not work, please make sure that the fault is not due to:
1.
2.
no power
no water in the reservoir.
If the power cable is damaged or the machine needs servicing, please contact the
nearest SERVICE FORCE CENTRE
16
TECHNICAL SPECIFICATIONS
•
Width
594 mm
•
Depth
475 mm
•
Height
378 mm
•
Capacity of water reservoir
2.5 l
•
Net weight
28 kg
•
Gross weight
31 kg
•
Supply voltage
230 V
•
Rated power
2000 W
•
Power absorbed by the heating element
1700 W
•
Power absorbed by the pump
50 W
•
Working pressure
12 bar
•
Fuse
13 A
33/35
17
AFTER-SALES SERVICE, SPARE PARTS AND GUARANTEE
SERVICE & SPARE PARTS
If you wish to purchase spare parts or require an engineer, contact your
local AEG Service Force Centre by telephoning:
08705 929 929
Your telephone call will be automatically routed to the Service Centre covering your
postcode area.
For the address of you local Service Force Centre or for further information regarding
Service Force, please visit the website as www.serviceforce.co.uk
When you contact the Service Centre they will need the following information:
1. Your name & address, including postcode.
2. Your telephone number
3. Clear and concise details of the fault.
4. The model, serial and production number.
This information can be found on the rating plate. The rating plate is on the
inner edge of the door on the right.
5. Date of purchase. Please note that it will be necessary to provide proof of
purchase for any in guarantee service call.
In-guarantee customers should ensure that the chapter headed "What to do if...“ has
been read, as the engineer will make a charge if the fault is not a mechanical
or electrical breakdown.
CUSTOMER CARE
For general enquiries concerning your AEG appliance or for further information on AEG
products please contact our Customer Care Department by letter or telephone at the
address below or visit our website at www.aeg.co.uk
Customer Care Department
AEG Domestic Appliances
101 Oakley,
Luton,
Beds,
LU4 9XF
Tel. 08705 350350 (*)
(*) Calls to this number may be recorded for training purposes.
34/35
GUARANTEE CONDITIONS
AEG offer the following guarantee to the first purchaser of this appliance.
1. The guarantee is valid for 24 months commencing when the appliance is handed over to the
first retail purchaser, which must be verified by purchase invoice or similar documentation.
The guarantee does not cover commercial use.
2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty
materials. The guarantee does not cover appliances where defects or poor performance are due
to misuse, accidental damage, neglect, faulty installation, unauthorised modification or attempted
repair, commercial use or failure to observe requirements and recommendations set out in the
instruction book. This guarantee does not cover such parts as light bulbs, removable glassware or
plastic.
3. Should guarantee repairs be necessary the purchaser must inform the nearest AEG Service
Force Centre (manufacturer’s service or authorised agent). AEG reserves the right to stipulate the
place of the repair (i.e. the customer’s home, place of installation or AEG workshop).
4. The guarantee or free replacement includes both labour and material.
5. Repairs carried out under guarantee do not extend the guarantee period for the appliance.
Parts removed during guarantee repairs become property of AEG.
6. The purchaser’s statutory rights are not affected by this guarantee.
EUROPEAN GUARANTEE
If you should move to another country within Europe then your guarantee moves with you to your
new home subject to the following qualifications:
* The guarantee starts from the date you first purchased your product.
* The guarantee is for the same period and to the same extent for labour and parts as exist in the
new country of use for this brand or range of products.
* This guarantee relates to you and cannot be transferred to another user.
* Your new home is within the European Community (EC) or European Free Trade Area.
* The product is installed and used in accordance with our instructions and is only used
domestically, i.e. a normal household
* The electrical supply complies with the specification given in the rating label.
* The product is installed taking into account regulations in your new country.
Before you move, please contact your nearest Customer Care Centre, listed below, to give them
details of your new home. They will then ensure that the local Service Organisation is aware of
your move and able to look after you and your appliances.
France
Germany
Italy
Sweden
UK
+33
+49
+39
+46
+44
(0)3 44 62 2929
(0)800 2347378
(0)800 117511
(0)8 672 5360
(0)1582 588809
35/35
04501150
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
Http://www.aeg.hausgeraete.de
© Copyright by AEG
Download PDF

advertising