FlaskScrubber & SteamScrubber
®
Laboratory Glassware Washers
®
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
TABLE
of
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Flexible Cycle Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
FlaskScrubber® Vantage® Series Laboratory Glassware Washers
Features & Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specifications & Ordering Information . . . . . . . . . . . . . . . . . 11
FlaskScrubber ® Laboratory Glassware Washers
Features & Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specifications & Ordering Information . . . . . . . . . . . . . . . . . 13
SteamScrubber ® Laboratory Glassware Washers
Features & Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Specifications & Ordering Information . . . . . . . . . . . . . . . . . 15
Dimensional Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Companion Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Made in U.S.A.
CONTENTS
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
OVERVIEW
Left: The FlaskScrubber Vantage Series Laboratory
Glassware Washer has advanced features for monitoring and controlling contaminants, including
water conductivity sensor, HEPA filtered drying
and RS-232 port. The washer includes a lower
spindle rack with options for an upper rack.
Inset: Upper standard open and spindle racks
feature side release latches allowing racks to be
easily lifted out for unloading or exchanging with
another upper rack.
Designed primarily to hold narrowneck glassware such as volumetrics and Erlenmeyer flasks, the FlaskScrubber has a lower
rack with 36 spindles and may be outfitted with specialized
inserts to accommodate pipets. Although the SteamScrubber
and FlaskScrubber are distinct in their primary uses, the standard open racks and spindles racks are interchangeable making
these washers more flexible and versatile than ever before. If
your glassware mix currently includes both narrowneck and
general glassware or changes in the future, just add the racks
and inserts you need to accommodate your needs.
Flexibility, durability, maximum cleanability and energyefficiency have been engineered in to every Labconco
laboratory glassware washer.
Flexibility
Labconco offers two distinct washer types for different
glassware mixes: the SteamScrubber and the FlaskScrubber.
Designed primarily to hold general glassware such as beakers,
utensils, test tubes, Petri dishes and BOD bottles, the
SteamScrubber comes with upper and lower standard open
racks that accommodate a wide variety of baskets and inserts.
3
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
OVERVIEW
The SteamScrubber Laboratory Glassware Washer is available in undercounter
and freestanding styles. Upper and lower standard racks accommodate a variety of
accessory baskets and inserts for beakers and specialized glassware.
The FlaskScrubber Laboratory Glassware Washer is available in undercounter
and freestanding styles. The lower spindle rack is interchangeable with a standard rack should laboratory needs change or for laboratories with a broad mix
of glassware.
Flexible cycle programs give the user control in selecting the
right combination of parameters including the following:
• washing time and temperature
• steam generation
• number of total and pure water rinses
• final rinse temperature
• drying time and temperature
Maximum Cleanability & Drying
Laboratories that conduct sensitive research demand
contaminant-free glassware. Many features work together to
achieve consistent, thorough cleaning:
• Powerful pump circulates water through the washer. Rated at
96 gallons/minute (363 liters/minute) on 115 volt, 60 Hz and
230 volt, 50 Hz models and 112 gallons/minute (424 liters/
minute) on 230 volt, 60 Hz models.
A keypad and LCD display allow cycle programs and parameters to be easily set or changed. Memory stores preset and user
set programs for reproducible protocols.
• A separate pump drains the wash and rinse water to
Durability
• Wash and rinse water temperature reaches 82° C (180° F) on
reduce risk of cross contamination between wash and
drain water.
115 volt models and 93° C (199° F) on 230 volt models to
better activate detergent, sanitize glassware and speed drying.
Rugged stainless steel interior, exterior, racks and inserts
withstand heavy use and reduce corrosion and contaminant
build-up.* Internal components such as pumps and seals are
laboratory-grade, engineered for long life.
• Built-in steam generator produces hot vapor to penetrate and
remove dried residue.
• Forced air drying ensures spot-free results. Drying temperature is programmable up to 70° C (158° F).
*Contact Labconco for compatibility with petroleum-based compounds.
4
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
OVERVIEW
Performance Testing
EPA Residue Testing
An outside analytical laboratory conducted visual cleanability
studies on the FlaskScrubber Glassware Washer outfitted with
various rack configurations. For the studies, a variety of six
beakers and two Erlenmeyer flasks were soiled with a viscous
mixture of iron oxide, motor oil, high vacuum grease, solid
vegetable shortening, and paraffin wax. The appearance of
the glassware was documented before and after washing and
drying in the FlaskScrubber Laboratory Glassware Washer
10-359-115. The following photographs show remarkably
clean glassware.
Since visibly clean glassware could still contain minute
amounts of contaminants, an outside analytical laboratory tested for microscopic residue on glassware cleaned in a
FlaskScrubber Laboratory Glassware Washer Model 10-359115. The laboratory tested the glassware to EPA Methods 200.7,
524.2, 525.1 and 8270. Test results showed low levels, at or near
the detection limits, of metals remaining in the samples. The
different parameters such as detergent type, upper or lower
rack, spindle or standard rack, did not affect results.
Based on results from the testing, the laboratory concluded
that the FlaskScrubber is a viable option for cleaning and
reuse of glassware used for trace metal, volatile organic and
semi-volatile organic compounds. Results were measured as
parts-per-billion and significance of the data will vary based on
individual application and analysis needs. Contact Labconco at
800-821-5525 or 816-333-8811 for a copy of the full report.
Energy Efficiency & Cost Savings
Before washing in
FlaskScrubber with Upper
Spindle Rack 10-359-125 using
LabSolutions Low-Foaming
Liquid Detergent 04-334-1
Before washing in FlaskScrubber
with Upper Standard Rack
10-359-200 using LabSolutions
Non-Foaming Powder Detergent
04-334
After
Compared to hand washing, the FlaskScrubber or
SteamScrubber can save on water usage. A faucet delivers
approximately 3 gallons/minute of tap water. Depending
on the contaminants on the glassware and type of glassware,
hand washing a load of glassware could take up to 20 gallons
or more. The FlaskScrubber or SteamScrubber uses as little
as 13.6 gallons per load and is not dependent on the habits of
the technician. The difference adds up to as much as 1664 gallons per year, saving both water and the electricity to heat it.
Labconco washers feature a delay start option to facilitate
running during off-peak hours when electricity is often less
expensive than during daylight hours. Aluminum-backed insulation and a fiberglass blanket surround every washer not only
for quiet operation, but to retain heat inside the washer, thus
conserving energy.
After
Take The Challenge
Labconco offers an online calculator to help you determine
how much you will save using a Labconco washer compared
to hand-washing. The Glassware Washer Cost Calculator
computes the costs of labor and water to wash and rinse glassware by hand versus to wash and rinse in a FlaskScrubber or
SteamScrubber.
Before washing in
FlaskScrubber with Upper
Spindle Rack 10-359-125 using
LabSolutions Low-Foaming
Liquid Detergent 04-334-1
Go to www.labconco.com/glassware-washing-cost-calculator
to determine if a Labconco washer will save you money.
After
5
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
SELECTION
GUIDE
Select the Labconco glassware washer that best suits your glassware mix
and level of contamination-sensitive research.
Primary Application
Electrical Configuration
Undercounter Available
Freestanding Available
Freestanding to
Mobile Conversion
Maximum Internal
Water Temperature
Washing
Forced Hot Air Drying
FlaskScrubber
Vantage Series
FlaskScrubber
Washing and drying primarily
narrowneck glassware such
as volumetric flasks. Advanced features for contaminationsensitive research.
208/230 volts, 50/60 Hz
convertible to undercounter
Washing and drying primarily
narrowneck glassware such as
volumetric flasks.
115 volts, 60 Hz
•
•
•
208/230 volts, 50/60 Hz
No
Yes
93° C (199° F)
Through Spindles &
Two Wash Arms
Through Spindles &
Throughout Tank
82° C (180° F)
Through Spindles &
Two Wash Arms
Through Spindles &
Throughout Tank*
93° C (199° F)
Through Spindles &
Two Wash Arms
Through Spindles &
Throughout Tank*
ADVANCED FEATURES:
•
•
•
•
•
•
•
HEPA Filtered Drying
Water Conductivity Sensor
RS-232 Port
Automatic Liquid
Detergent Dispenser
Automatic Rinse Aid
Dispenser
Racks Included
Lower 36-spindle rack
Lower 36-spindle rack
Lower 36-spindle rack
Viewing window with light Standard
OptionalOptional
ACCOMMODATES OPTIONAL RACKS:
•
•
•
Lower Test Tube Spindle Rack
•
ACCOMMODATES OPTIONAL BASKETS and INSERTS:
Utensil Holder
•
Basket
Utensil
•
Bulk Tube Insert
•
Tube Insert
Culture
•
Inserts
Labware
•
Bottle Insert
BOD
•
Insert
48-Pin
•
Dish Insert
Petri
•
Sequencing Plate Insert
DNA
•
Insert
Tray
•
Pipet Insert
•
Upper Spindle Rack
Lower Spindle Rack
Upper Standard Rack
Lower Standard Rack
Included
* FlaskScrubber 33 models feature forced air drying throughout tank only.
6
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
IncludedIncluded
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
SELECTION
GUIDE
SteamScrubber
Washing and drying primarily
beakers and other wide-mouth
or specialized glassware.
115 volts, 60 Hz
208/230 volts, 50/60 Hz
••
••
Yes
82° C (180° F)
Through Three
Wash Arms
Throughout Tank
93° C (199° F)
Through Three
Wash Arms
Throughout Tank
Freestanding-To Mobile Conversion Kits, available for
FlaskScrubber and SteamScrubber models, add portability.
Upper and lower
Upper and lower
standard open racks
standard open racks
Optional Optional
•
•
•
•
IncludedIncluded
The side compartment of the FlaskScrubber Vantage Series Washer houses
the 99.97% efficient HEPA filter and automatic liquid detergent and rinse
aid dispensers.
IncludedIncluded
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Pipets may be thoroughly washed and dried in
FlaskScrubber and FlaskScrubber Vantage Series Washers.
Pipet Inserts attach to the spindle rack to allow the interior
of the pipets to be injected with water and detergent for
washing followed by hot air for drying.
7
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
FLEXIBLE
CYCLE
OPTIONS
Microprocessor control allows the user to select from seven preset programs or customize two different USER SET programs. FlaskScrubber
Vantage Series Washers and FlaskScrubber and SteamScrubber models for 230 volt operation have three additional preset programs (INTENSE,
Program
Unit of
Selectable
Measure
Set Points*
Delay Start
(hr)
Wash 1 Time
(min)
Detergent Dispense (Vantage Series Only)(ml)
Steam
(Yes/No)
Wash 2 Time
Wash 2 Temperature
(min)
(° F)
(° C)
Wash 3 Time (Vantage Series Only)
Wash 3 Temp (Vantage Series Only)
(min)
(° F)
(° C)
Detergent Dispense (Vantage Series Only)(ml)
Total Number of Rinses
Number of Pure Rinses
Final Rinse Temperature
(° F)
(° C)
Rinse Only
Factory
Setting
1-8
None
0-40
Y N
0
—
—
—
1-40** —
100-199*** —
38-93***
0, 10, 20, 30, 40
100-199
38-93
—
—
Plastic
Factory
Setting
Glass
Factory
Setting
Glass Plus
Factory
Setting
0
0
0
55 5
20
20
20
N
N
Y
1010 10
122
140
140
50
60
60
—
—
—
—
—
—
0-40
—
20
20
20
0-6
1
2
3
3
0-6
0
0
0
0
100
122
140
140
100-199†
38-93† 38 5060 60
Rinse Time
Rinse Aid Dispense
(min)
(ml)
1-30††
0-6
4
—
Dry Time
Dry Temperature
(min)
(° F)
(° C)
0 or 15-250
100-158
38-70
0
100
38
1530 30
122
140
140
50
60
60
Total Water Consumption
(gal)
(liters)
up to 27.2
up to 103
3.4
12.9
13.6
51.5
4
0
4
0
17
64.4
4
0
17
64.4
Total Factory Set Time (excluding
delays to heat water and air for
wash, rinse and dry cycles)
(min)
10 5186 96
Bold numbers indicate factory preset times.
Steam adds 10 minutes to total program time. Each rinse adds 4 minutes to total program time. Rinse time increases by 1.5 minutes for each pure water rinse.
Each rinse adds 3.4 gallons (12.9 liters) to total water consumption.
* Selectable set points do not apply to all programs.
**Vantage Series models select from 10, 20, 30 or 40 minutes.
***Maximum temperature is 180° F (82° C) on FlaskScrubber and SteamScrubber models for 115 volt operation.
† Maximum temperature is 140° F (60° C) for Rinse Only and Plastic Programs. Maximum temperature is 180° F (82° C) for all other programs on
FlaskScrubber and SteamScrubber models for 115 volt operation.
†† Selectable on User 2 program on FlaskScrubber and SteamScrubber only.
Select from factory set and user set programs with
the flexibility to easily change multiple parameters
on the intuitive LCD.
DISPLAY SCROLL BUTTONS.
Press to scroll through the
display screen.
LCD. Displays at-a-glance
program selection or details of
the program. Provides feedback
during program customization.
DISPLAY. Press to change
the display. When starting a
cycle program, press to show
the available cycle programs.
When modifying program
parameters, press to show
program parameters that may
be altered.
RUN/CANCEL. Initiates program selected. Terminates cycle
in progress.
PARAMETER CHANGE
BUTTONS. Press to change a
set point parameter.
8
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
FLEXIBLE
CYCLE
OPTIONS
INTENSE PLUS and EXTREME). Selectable set point parameters allow the programs to be altered by the user. Parameters selected by the user are
stored in memory for future recall.
Science
Factory
Setting
Science Plus
Factory
Setting
Dry Only
Factory
Setting
User 1
Factory
Setting
User 2
Factory
Setting
Intense
Factory
Setting
Intense Plus
Factory
Setting
Extreme
Factory
Setting
0
0
—
0
0
5
5—
5
5
20
20
—
20
20
NY —NN
0
0
0
10 1010
20
20
20
N YY
20
158
70
10
180
82
30 3040
180
180
199
82
82
93
20—
10
158
—
140
70
60
—
—
—
—
—
—
—
0
140
60
0
180
82
30 3040
180
180
199
82
82
93
20
4
0
158
70
20
4
0
158
70
—
—
—
—
—
20
2
0
140
60
20
2
0
180
82
20
5
0
180
82
4
0
4
0
—
—
4
0
4
0
40
140
60
40
140
60
60
140
60
15
140
60
15
140
60
50 5060
140
140
140
60
60
60
20.4
77.2
20.4
77.2
0
0
13.6
51.5
13.6
51.5
23.8
90.1
126
60 62 62
116
20
5
0
180
82
4 44
0
0
0
23.8
90.1
27.2
103
150 160190
FlaskScrubber Vantage Series and
FlaskScrubber and SteamScrubber
208/230 Volt Models only
9
20
6
0
199
93
FlaskScrubber® Vantage® Series Laboratory Glassware Washers
FEATURES
&
BENEFITS
For washing and drying primarily narrowneck glassware used in contamination-sensitive research.
Alarms sound and/or
display on the LCD to
alert the user to abnormal or unsafe events such
as HOT GLASS and
OVERFLOW.
User-set delayed start
(up to 8 hours) may be
programmed so that the
washer operates during
off-peak hours when
electricity may be less
expensive and more
plentiful.
Dual pumps, one
for washing and one
for draining, reduce
the potential for cross
contamination.
Up to 6 pure water rinses
may be programmed.
A built-in purified water
pump draws from a
storage tank or pressurized source for final rinses.
Water conductivity
monitoring. Sensor
measures the level of dissolved inorganics such as
calcium and ferrous ions
in the tank water, providing validation of water
cleanliness, hardness and
rinsing thoroughness.
Confirms that detergent,
rinse aid and purified
water have been properly
dispensed.
Quiet, energy-efficient
operation at 58 decibels.
Aluminum-backed,
sound-deadening insulation and fiberglass
blanket absorb noise
and optimize internal
tank temperature to
conserve energy.
360° rotating upper and
lower wash arms distribute water and detergent.
Attractive and durable
Type 304 stainless
steel sides, top, door
and tank.*
INCLUDES Lower
stainless steel spindle
rack with 36 detachable
spindles, 18 glassware
holders, 36 height
adjustment clips and 10
additional interchangeable small spindles.
Large volumes of water
are propelled through
the spindles and into the
bulb of each flask for
high-powered cleaning.
Tall spindles hold flasks
from 50 ml to 2000 ml;
small spindles from 1 ml
to 25 ml.
Versatile rack options.
Spindles on the lower
rack may be easily
detached and plugged so
that the rack may accommodate accessory inserts
for a variety of beakers
and specialized glassware.
An optional 30-spindle
upper rack increases
washer capacity. Optional
racks, including interchangeable Upper and
Lower Standard Racks,
and accessory inserts are
sold separately. See pages
18 and 19.
Sanitizing high heat.
Water temperature
reaches 93° C (199° F)
to sanitize glassware and
for enhanced washing,
rinsing and faster drying.
Automatic rinse aid
dispenser. A peristaltic
pump automatically
draws a programmed
amount of LabSolutions
Neutralizing Acid Rinse
or other rinse aid during the rinse cycle. In
addition, a manual-fill
dispenser is located in
the door.
Made in U.S.A.
Exclusive Labconco feature
HEPA-filtered forced air
drying system through
the spindles. Hot air
is blown through the
spindles to the interior of
narrowneck glassware
for complete dryness.
No separate dryer or
oven is needed. A HEPA
filter, 99.97% efficient on
particulates 0.3 micron,
traps dust, lint and other
particles in the air introduced during drying.
Automatic liquid
detergent dispenser.
A peristaltic pump
automatically draws a
programmed amount of
LabSolutions Liquid
Detergent or other automatic washer liquid detergent during wash cycles.
In addition, a manual-fill
dispenser for liquid or
powder detergent is
located in the door.
Powerful pump recirculates water at a high
rate to dislodge dried
contaminants for thorough cleaning. Rated at
96 gal/min (363 liters/
min) on 230 Volt, 50 Hz
models and 112 gal/
min (424 liters/min) on
230 Volt, 60 Hz models.
Steam generator.
Produces hot vapor to
penetrate and soften
dried contaminants for
more effective cleaning.
*Contact Labconco for compatibility with petroleum-based compounds.
10
RS-232 port. May be
used to transmit data
such as temperature,
cycle phase, water level
alarm and conductivity
to a user-supplied computer or chart recorder.
CE Mark. Washers
conform to the CE
(European Community)
requirements for electrical safety and electromagnetic compatibility.
Clear tempered safety
glass viewing window
with LED interior light
allows observation of the
cycle in progress.
Full two year warranty.
Is provided against
defects in materials and
workmanship.
ETL-listed.
Washers carry
the ETL mark signifying they are certified to
UL** Standard 61010-1
and CAN/CSA C22.2 No.
61010.1.
**UL® is a registered trademark of Underwriters Laboratories, Inc., Northbrook, IL.
FlaskScrubber® Vantage® Series Laboratory Glassware Washers
SPECIFICATIONS
&
ORDERING
INFORMATION
• Alarms with display for HOT GLASS, PLEASE WAIT, WATER LOW,
OVERFLOW, LIQ DETER, RINSE AID, DRAIN FAIL and LOW
TEMP. Audible alarms self cancel after one minute.
• User-set delayed start (up to 8 hours)
• Type 304, stainless steel exterior sides, top, door, tank, upper and
lower wash arms
• Clear tempered safety glass viewing window
• LED interior light that illuminates when door is latched
• One-piece, stainless steel, fine mesh particle drain filter
• Four leveling feet
• 3/8" Female NPT inlet fitting for hot tap water connection
• Factory-installed drain hose and band clamp
• Two year warranty on parts and labor
• Made in the U.S.A.
• IQ/OQ available. Visit www.labconco.com or call 800-821-5525.
FlaskScrubber Vantage Series
Laboratory Glassware Washer
10-359-116 is shown with Base
Stand 10-359-126.
All models feature:
• Freestanding design, convertible to undercounter
• Lower spindle rack, of Type 304 stainless steel, with 36 detach-
All models conform to:
• UL* 61010-1
• CAN/CSA C22.2 No. 61010.1
• CE Conformity Marking
able large spindles, 18 glassware holders, 36 clips and 10 additional
interchangeable small spindles
• Water conductivity sensor with display (µs)
• Water temperature to 93° C (199° F)
• LCD information center, Display button, Run/Cancel button, scroll
buttons and selection buttons to program and monitor cycles
• Pump rated at 96 gal/min (363 liters/min) when operated on 230
Volt, 50 Hz and 112 gal/min (424 liters/min) on 230 Volt, 60 Hz
• Drain pump to evacuate over 7 gal/min (26 liters/min)
• Purified water pump to bring non-pressurized or pressurized
purified water into the tank for up to six pure water rinses
• Steam generator that produces hot vapor before the WASH 2 cycle
(RINSE ONLY and PLASTIC programs excluded)
• Aluminum-backed insulation and fiberglass blanket for thermal and
sound insulation
• Operation at 58 decibels
• Automatic liquid detergent dispenser with peristaltic pump
• Automatic rinse aid dispenser with peristaltic pump
• Manual-fill detergent dispenser for powder or liquid detergent
• Manual-fill rinse aid solution dispenser
• HEPA-filtered forced air drying through the spindles programmable
up to 250 minutes and from 38-70° C (100-158° F). HEPA filter is
99.97% efficient on particulates 0.3 micron.
• Ten factory-set cycle programs: RINSE ONLY, PLASTIC, GLASS,
GLASS PLUS, SCIENCE, SCIENCE PLUS, INTENSE, INTENSE
PLUS, EXTREME and DRY ONLY
• Two user-set cycle programs
Catalog #
Style 10-359-116 Freestanding**
Electrical
Requirements†
All models require:
•20 amp circuit breaker
• Recommended inlet water temperature 60° C (140° F)
• Minimum optional purified water pressure 0 psi
• Water consumption per fill 3.4 gallons (13 liters)
• Hot tap water pressure at the washer 20-120 psi (138-827 KPa)
• Hot tap water flow rate 1.25 gallons (4.7 liters) per minute
• 3/8" OD copper tubing for connection to the water inlet valve
• Purified water with supply piping minimum 3/8" ID to permit at
least 0.9 gallon (3.4 liters) per minute flow
Optional accessories and companion products
on pages 18 - 22 include:
• Base Stand
• Upper Spindle Rack
• Upper and Lower Standard Racks
• Lower Test Tube Spindle Rack
• Baskets and Inserts
• Glassware Holders
• Drain Water Cooling Kit
• LabSolutions Detergents and Rinse
• ScrubberMate Cart, Glassware Carts and Carboy Caddy
• WaterPro RO Stations and accessories
Maximum Internal Water Temperature
Viewing Window
and Light
Overall Dimensions
with Door Closed
208/230 Volts,
93° C (199° F)
Yes
32.2" w x 27.5" d x 34.2-36.2" h
50/60 Hz, 11 Amps
*UL® is a registered trademark of Underwriters Laboratories, Inc., Northbrook, IL.
**Convertible to undercounter
Shipping Weight
294 lbs.
(133 kg)
†20 amp circuit breaker is required.
Exclusive Labconco feature
11
FlaskScrubber® Laboratory Glassware Washers
FEATURES
&
BENEFITS
For washing and drying primarily narrowneck glassware.
Steam generator.
Produces hot vapor to
penetrate and soften
dried contaminants for
more effective cleaning.
Dual pumps, one
for washing and one
for draining, reduce
the potential for cross
contamination.
User-set delayed start
(up to 8 hours) may be
programmed so that the
washer operates during
off-peak hours when
electricity may be less
expensive and more
plentiful.
Up to 6 pure water rinses
may be programmed.
A built-in purified water
pump draws from a
storage tank or pressurized source for final rinses.
Alarms sound and/
or display on the LCD
to alert the user to
abnormal or unsafe
events such as HOT
GLASS and OVERFLOW.
360° rotating upper and
lower wash arms distribute water and detergent.
Powerful pump recirculates water at a high
rate to dislodge dried
contaminants for thorough cleaning. Rated at
96 gal/min (363 liters/
min) on 115 Volt, 60
Hz and 230 Volt, 50 Hz
models and 112 gal/min
(424 liters/min) on 230
Volt, 60 Hz models.
Attractive and durable
Type 304 stainless steel
door and tank.* Freestanding models also
have stainless steel sides
and top.
Rinse solution dispenser.
Allows manual addition
of mildly acidic rinse to
alter pH and eliminate
alkaline detergent carryover. The dispenser holds
approximately 170 milliliters, enough for 40 or
more cycles.
Detergent dispenser
for powder or liquid
detergent. Releases a
manually premeasured
amount ensuring clean
labware.
INCLUDES Lower
stainless steel spindle
rack with 36 detachable
spindles, 18 glassware
holders, 36 height
adjustment clips and 10
additional interchangeable small spindles.
Large volumes of water
are propelled through
the spindles and into the
bulb of each flask for
high-powered cleaning.
Tall spindles hold flasks
from 50 ml to 2000 ml;
small spindles from 1 ml
to 25 ml.
Low profile FlaskScrubber
33 undercounter models
available. Minimum
height of 32.9" allows
installation under
ADA**-height cabinetry.
Made in U.S.A.
Versatile rack options.
Spindles on the lower
rack may be easily
detached and plugged so
that the rack may accommodate accessory inserts
for a variety of beakers
and specialized glassware.
An optional 30-spindle
upper rack increases
washer capacity. Optional
racks, including interchangeable Upper and
Lower Standard Racks,
and accessory inserts are
sold separately. See pages
18 and 19.
Full two year warranty.
Is provided against
defects in materials and
workmanship.
Sanitizing high heat.
Water temperature
reaches 93° C (199° F)
on 230 Volt models to
sanitize glassware and for
enhanced washing, rinsing and faster drying.
Quiet, energy-efficient
operation at 58 decibels.
Aluminum-backed,
sound-deadening
insulation and fiberglass
blanket absorb noise
and optimize internal
tank temperature to
conserve energy.
Forced air drying system.
Hot air is blown into the
tank to dry glassware.
Except for FlaskScrubber
33 models, air is also
blown through the spindles to the interior of the
glassware. No separate
dryer or oven is needed.
Exclusive Labconco feature
*Contact Labconco for
compatibility with petroleumbased compounds.
* *Americans with Disabilities Act
12
Optional clear tempered
safety glass viewing
window with LED interior light allows observation of the cycle in progress. Available standard
on some models.
†UL® is a registered trademark of
Underwriters Laboratories, Inc.,
Northbrook, IL.
ETL-listed.
Washers carry
the ETL mark signifying
they are certified to UL†
61010-1 and CAN/CSA
C22.2 No. 61010.1.
CE Mark. Washers
conform to the CE
(European Community)
requirements for electrical safety and electromagnetic compatibility.
FlaskScrubber® Laboratory Glassware Washers
SPECIFICATIONS
&
ORDERING
INFORMATION
• Type 304, stainless steel top, door, tank, upper and lower wash arms.
Freestanding models also have stainless steel exterior sides and top.
• One-piece, stainless steel, fine mesh particle drain filter
• Four leveling feet
• 3/8" Female NPT inlet fitting for hot tap water connection
• Factory-installed drain hose and band clamp
• Two year warranty on parts and labor
• Made in the U.S.A.
• IQ/OQ available. Visit www.labconco.com or call 800-821-5525.
All models conform to:
•UL** 61010-1
•CAN/CSA C22.2 No. 61010.1
•CE Conformity Marking (208/230 Volt models only)
All models require:
•20 amp circuit breaker
•Recommended inlet water temperature 60° C (140° F)
•Minimum optional purified water pressure 0 psi
•Water consumption per fill 3.4 gallons (13 liters)
•Hot tap water pressure at the washer 20-120 psi (138-827 KPa)
•Hot tap water flow rate 1.25 gallons (4.7 liters) per minute
•3/8" OD copper tubing for connection to the water inlet valve
•Purified water with supply piping minimum 3/8" ID to permit at
FlaskScrubber Laboratory
Glassware Washer 10-359-114
includes a viewing window
and light.
All models feature:
• Lower spindle rack, of Type 304 stainless steel, with 36 detachable large
spindles, 18 glassware holders, 36 clips and 10 additional interchangeable small spindles
• LCD information center, Display button, Run/Cancel button, scroll
buttons and selection buttons to program and monitor cycles
• Pump rated at 96 gal/min (363 liters/min) when operated on 115 Volts,
60 Hz and 230 Volts, 50 Hz and 112 gal/min (424 liters/min) on
230 Volts, 60 Hz
• Drain pump to evacuate over 7 gal/min (26 liters/min)
• Purified water pump to bring non-pressurized or pressurized purified
water into the tank for up to six pure water rinses
• Steam generator that produces hot vapor before the WASH 2 cycle
(RINSE ONLY and PLASTIC programs excluded)
• Aluminum-backed insulation and fiberglass blanket for thermal and
sound insulation
• Operation at 58 decibels
• Manual-fill detergent dispenser for powder or liquid detergent
• Manual-fill rinse aid solution dispenser
• Forced air drying into the tank programmable up to 250 minutes and
from 38-70° C (100-158° F)
• Seven factory-set cycle programs: RINSE ONLY, PLASTIC, GLASS,
GLASS PLUS, SCIENCE, SCIENCE PLUS, and DRY ONLY. All
208/230 Volt models have three additional programs for a total of ten:
INTENSE, INTENSE PLUS and EXTREME.
• Two user-set cycle programs
• Programs may be locked to prevent unauthorized changes
• Alarms with display for HOT GLASS, PLEASE WAIT, WATER LOW,
WATER HIGH, OVERFLOW, LIQ DETER, RINSE AID, DRAIN FAIL
and LOW TEMP. Audible alarms self cancel after one minute.
• User-set delayed start (up to 8 hours)
Catalog #
Style 10-359-108 Std. Undercounter
10-359-109 Std. Undercounter
10-359-110 Std. Undercounter
10-359-111 Std. Undercounter
10-359-185 33 Undercounter
10-359-186 33 Undercounter
10-359-187 33 Undercounter
10-359-188 33 Undercounter
10-359-112 Std. Freestanding
10-359-113 Std. Freestanding
10-359-114 Std. Freestanding
10-359-115 Std. Freestanding
Electrical
Requirements†
Standard models also feature:
•Forced air drying through the spindles
FlaskScrubber 33 models also feature:
•Minimum 32.9" height to fit under ADA*-height cabinetry
Options include:
•Standard freestanding and undercounter styles, FlaskScrubber 33
undercounter styles
•Water temperature to 82° C (180° F) on 115 Volt models and 93° C
(199° F) on 230 Volt models
•Clear tempered safety glass viewing window and 25-watt interior
light that illuminates when door is latched
Optional accessories and companion products
on pages 18 - 22 include:
•Base Stand • Upper Spindle Rack • Lower Test Tube Spindle Rack
•Upper and Lower Standard Racks • Baskets and Inserts
•Glassware Holders • Freestanding-to-Mobile Conversion Kits
•Drain Water Cooling Kit • LabSolutions Detergents and Rinse
•ScrubberMate Cart, Glassware Carts and Carboy Caddy
•WaterPro RO Stations and accessories
Max. Water Viewing Window Forced Air Dry
Temperature
and Light
Through Spindles
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
Exclusive Labconco feature * Americans with Disabilities Act
least 0.9 gallon (3.4 liters) per minute flow
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
No
No
Yes
Yes
No
No
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
Yes
Overall Dimensions
with Door Closed
Shipping Weight
24.1" w x 27.4" d x 34.1-36.1" h
24.1" w x 27.4" d x 34.1-36.1" h
24.1" w x 27.4" d x 34.1-36.1" h
24.1" w x 27.4" d x 34.1-36.1" h
24.1" w x 27.4" d x 32.9-34.9" h
24.1" w x 27.4" d x 32.9-34.9" h
24.1" w x 27.4" d x 32.9-34.9" h
24.1" w x 27.4" d x 32.9-34.9" h
24.2" w x 27.5" d x 34.2-36.2" h
24.2" w x 27.5" d x 34.2-36.2" h
24.2" w x 27.5" d x 34.2-36.2" h
24.2” w x 27.5” d x 34.2-36.2” h
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
239 lbs. (108 kg)
239 lbs. (108 kg)
239 lbs. (108 kg)
239 lbs. (108 kg)
**UL® is a registered trademark of Underwriters Laboratories, Inc., Northbrook, IL.
13
†20 amp circuit breaker is required.
SteamScrubber® Laboratory Glassware Washers
FEATURES
&
BENEFITS
For washing and drying primarily beakers and other wide-mouth or specialized glassware.
Steam generator.
Produces hot vapor to
penetrate and soften
dried contaminants for
more effective cleaning.
Forced air drying
system. Hot air is blown
into the tank to dry glassware. No separate dryer
or oven is needed.
Dual pumps, one for
washing and one for
draining, reduce the
potential for cross
contamination.
User-set delayed start
(up to 8 hours) may be
programmed so that the
washer operates during
off-peak hours when
electricity may be less
expensive and more
plentiful.
Up to 6 pure water rinses
may be programmed.
A built-in purified water
pump draws from a
storage tank or pressurized source for final rinses.
360° rotating upper,
middle and lower wash
arms distribute water
and detergent.
Powerful pump recirculates water at a high
rate to dislodge dried
contaminants for thorough cleaning. Rated at
96 gal/min (363 liters/
min) on 115 Volt, 60
Hz and 230 Volt, 50 Hz
models and 112 gal/min
(424 liters/min) on 230
Volt, 60 Hz models.
Detergent dispenser
for powder or liquid
detergent. Releases a
manually premeasured
amount ensuring clean
labware.
Low profile SteamScrubber
33 undercounter models
available. Minimum
height of 32.9" allows
installation under ADA*height cabinetry.
Made in U.S.A.
Full two year warranty.
Is provided against
defects in materials and
workmanship.
INCLUDES Upper and
lower stainless steel
standard open racks.
Accommodate a variety
of accessory inserts holding the broadest range of
glassware. Inserts are sold
separately. See pages 18
and 19.
Attractive and durable
Type 304 stainless steel
door and tank. Freestanding models also
have stainless steel sides
and top.
Quiet, energy-efficient
operation at 58 decibels. Aluminum-backed,
sound-deadening
insulation and fiberglass
blanket absorb noise
and optimize internal
tank temperature to
conserve energy.
Versatile rack options.
The standard open racks
are interchangeable with
optional upper and lower
spindle racks. Additional
racks are sold separately.
See page 18.
Sanitizing high heat.
Water temperature
reaches 93° C (199° F)
on 230 Volt models to
sanitize glassware and for
enhanced washing, rinsing and faster drying.
Rinse solution dispenser. Allows manual addition of mildly acidic rinse
to alter pH and eliminate
alkaline detergent carryover. The dispenser holds
approximately 170 milliliters, enough for 40 or
more cycles.
Exclusive Labconco feature
Alarms sound and/or
display on the LCD to
alert the user to abnormal or unsafe events such
as HOT GLASS and
OVERFLOW.
*Contact Labconco for
compatibility with petroleumbased compounds.
* *Americans with Disabilities Act
14
Optional clear tempered
safety glass viewing
window with LED interior light allows observation of the cycle in progress. Available standard
on some models.
†UL® is a registered trademark of
Underwriters Laboratories, Inc.,
Northbrook, IL.
ETL-listed.
Washers carry
the ETL mark signifying
they are certified to UL†
Standard 61010-1 and
CAN/CSA C22.2 No.
61010.1.
CE Mark. Washers
conform to the CE
(European Community)
requirements for electrical safety and electromagnetic compatibility.
SteamScrubber® Laboratory Glassware Washers
SPECIFICATIONS
&
ORDERING
INFORMATION
arms. Freestanding models also have stainless steel exterior sides and top.
• One-piece, stainless steel, fine mesh particle drain filter
• Four leveling feet
• 3/8" Female NPT inlet fitting for hot tap water connection
• Factory-installed drain hose and band clamp
• Two year warranty on parts and labor
• Made in the U.S.A.
• IQ/OQ available. Visit www.labconco.com or call 800-821-5525.
All models conform to:
• UL* 61010-1
• CAN/CSA C22.2 No. 6 1010.1
• CE Conformity Marking (208/230 Volt models only)
All models require:
•20 amp circuit breaker
• Recommended inlet water temperature 60° C (140° F)
• Minimum optional purified water pressure 0 psi
• Water consumption per fill 3.4 gallons (13 liters)
• Hot tap water pressure at the washer 20-120 psi (138-827 KPa)
• Hot tap water flow rate 1.25 gallons (4.7 liters) per minute
• 3/8" OD copper tubing for connection to the water inlet valve
• Purified water with supply piping minimum 3/8" ID to permit at least
SteamScrubber Laboratory
Glassware Washer 10-359-102
is shown with 48-Pin Insert
10-359-122, Petri Dish Insert
10-359-120, Bulk Tube Insert
15-352-827, Utensil Holder
15-352-826 and BOD Bottle
Insert 10-359-121.
All models feature:
• Upper and lower standard open racks of Type 304 stainless steel
• LCD information center, Display button, Run/Cancel button, scroll
buttons and selection buttons to program and monitor cycles
• Pump rated at 96 gal/min (363 liters/min) when operated on 115
Volts, 60 Hz and 230 Volts, 50 Hz and 112 gal/min (424 liters/min) on
230 Volts, 60 Hz
• Drain pump to evacuate over 7 gal/min (26 liters/min)
• Purified water pump to bring non-pressurized or pressurized
purified water into the tank for up to six pure water rinses
• Steam generator that produces hot vapor before the WASH 2 cycle
(RINSE ONLY and PLASTIC programs excluded)
• Aluminum-backed insulation and fiberglass blanket for thermal
and sound insulation
• Operation at 58 decibels
• Manual-fill detergent dispenser for powder or liquid detergent
• Manual-fill rinse aid solution dispenser
• Forced air drying programmable up to 250 minutes and from
38-70° C (100-158° F)
• Seven factory-set cycle programs: RINSE ONLY, PLASTIC, GLASS,
GLASS PLUS, SCIENCE, SCIENCE PLUS, and DRY ONLY. All
208/230 Volt models have three additional programs for a total of ten:
INTENSE, INTENSE PLUS and EXTREME.
• Two user-set cycle programs
• Programs may be locked to prevent unauthorized changes
• Alarms with display for HOT GLASS, PLEASE WAIT, WATER LOW,
WATER HIGH, OVERFLOW, LIQ DETER, RINSE AID DRAIN FAIL
and LOW TEMP. Audible alarms self cancel after one minute.
• User-set delayed start (up to 8 hours)
• Type 304, stainless steel top, door, tank, upper, middle and lower wash
Catalog #
Style 10-359-100 Std. Undercounter
10-359-101 Std. Undercounter
10-359-102 Std. Undercounter
10-359-103 Std. Undercounter
10-359-181 33 Undercounter
10-359-182 33 Undercounter
10-359-183 33 Undercounter
10-359-184 33 Undercounter
10-359-104 Std. Freestanding
10-359-105 Std. Freestanding
10-359-106 Std. Freestanding
10-359-107 Std. Freestanding
Exclusive Labconco feature
0.9 gallon (3.4 liters) per minute flow
SteamScrubber 33 models also feature:
• Minimum 32.9" height to fit under ADA*-height cabinetry
Options include:
• Standard freestanding and undercounter styles, SteamScrubber 33
undercounter styles
• Water temperature to 82° C (180° F) on 115 Volt models and 93° C
(199° F) on 230 Volt models
• Clear tempered safety glass viewing window and 25-watt interior light
that illuminates when door is latched
Optional accessories and companion products on pages 18 - 22 include:
• Base Stand
• Upper and Lower Spindle Racks
• Lower Test Tube Spindle Rack
• Baskets and Inserts
• Freestanding-to-Mobile Conversion Kits
• Drain Water Cooling Kit
• LabSolutions Detergents and Rinse
• ScrubberMate Cart, Glassware Carts and Carboy Caddy
• WaterPro RO Stations and accessories
Electrical
Requirements†
Max. Water Temperature
Viewing Window
and Light
Overall Dimensions
with Door Closed
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
115 Volts, 60 Hz, 16 Amps
208/230 Volts, 50/60 Hz, 11 Amps
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
82° C (180° F)
93° C (199° F)
No
No
Yes
Yes
No
No
Yes
Yes
No
No
Yes
Yes
24.1" w x 27.4" d x 34.1-36.1" h
24.1" w x 27.4" d x 34.1-36.1" h
24.1" w x 27.4" d x 34.1-36.1" h
24.1" w x 27.4" d x 34.1-36.1" h
24.1" w x 27.4" d x 32.9-34.9" h
24.1" w x 27.4" d x 32.9-34.9" h
24.1" w x 27.4" d x 32.9-34.9" h
24.1" w x 27.4" d x 32.9-34.9" h
24.2" w x 27.5" d x 34.2-36.2" h
24.2" w x 27.5" d x 34.2-36.2" h
24.2" w x 27.5" d x 34.2-36.2" h
24.2" w x 27.5" d x 34.2-36.2" h
†20 amp circuit breaker is required.
Shipping Weight
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
206 lbs. (93 kg)
235 lbs. (107 kg)
235 lbs. (107 kg)
235 lbs. (107 kg)
235 lbs. (107 kg)
*UL® is a registered trademark of Underwriters Laboratories, Inc., Northbrook, IL.
15
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
DIMENSIONAL
DATA
Undercounter
FlaskScrubber &
SteamScrubber
Min.Max.
StyleA
25.5"(64.8
cm) cm)
25.5"(64.8
(without
trim) trim)
(without
Std. 34.2"36.2"
(86.6 cm) (91.7 cm)
A
33 32.9"34.9"
(83.6 cm) (88.6 cm)
A
B
Std. 11.9"13.9"
(30.3 cm) (35.4 cm)
B
B
33 10.9"12.9"
(27.8 cm) (32.8 cm)
Freestanding
FlaskScrubber &
SteamScrubber
13.9" MAX
MAX (35.4
(35.4 cm)
cm)
13.9"
11.9" MIN
MIN (30.3
(30.3 cm)
cm)
11.9"
FlaskScrubber
Vantage Series*
*Freestanding model
may be converted
to undercounter
13.9" MAX (35.4 cm)
11.9" MIN (30.3 cm)
SIDE
FRONT
16
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
DIMENSIONAL
DATA
Inside Dimensions with Lower and Upper Spindle Racks (all models)
FRONT
SIDE
Inside Dimensions with Lower and Upper Standard Racks (all models)
FRONT
SIDE
17
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
ACCESSORIES
V Accessories
Guide to
Use the icon key below to select accessories that fit your washer. Racks
can accommodate a maximum of two inserts except Utensil Holders
and
V Utensil Baskets; racks can hold a maximum of five Utensil
Holders* or four Utensil Baskets.
For use in SteamScrubber
V
V
V
For use in FlaskScrubber VV
For use in FlaskScrubber Vantage Series
V
V
s
Fits in Upper Standard Rack
V
t
Fits in Lower Standard Rack
tV Fits in Lower Spindle Rack with spindles removed and plugged
V
s
Lower Test Tube Spindle Racks
V
May be used in place of the Lower Standard Rack in any SteamV V or the Lower Spindle Rack in any FlaskScrubber or FlaskScrubber
Scrubber Vantage Series Washer. Hold test tubes, vials and other
V glassware containers up to 10 mm in diameter. Water and
laboratory
detergent are injected through the spindles to clean and rinse the inside
of the tubes. In addition, when used in a FlaskScrubber or FlaskScrubber Vantage Series Washer, hot air is forced through the spindles
to dry the inside of the test tubes. Constructed of Type 304 stainless
steel. Include 150 each spindles, 2.0" h x 1/8" OD (5 cm x 3 mm) with
nylon fasteners and riser. The riser, when placed on top of the spindles,
elevates tubes 3/4" (19 mm) from the bottom of the spindles to allow
for proper drainage.
Fits in Upper Spindle Rack with spindles removed and plugged
Upper Spindle Racks
V
Constructed of Type 304 stainless
steel. Include side release latches,
30 removable spindles, 30 adjustable height clips, 10 small spindles,
VV
15 plastic glassware holders, tool
to remove spindles, 30 nylon
V
plugs, and wash arm. Spindles
may be removed and plugged to accommodate accessory inserts (sold
separately). Spindle dimensions: 5.2" high x 1/4" OD (13.2 x 0.6 cm).
V dimensions: 20.0" w x 20.9" d x 7.2" high (51 x 53 x 18 cm).
Overall
VV
Accommodate glassware up to 8.9" high (22.6 cm).
V
Catalog #V
Description 10-359-125
V
V
10-359-201
V
Upper Spindle Rack for FlaskScrubber and FlaskScrubber
Vantage Series Glassware Washers. Includes side rails for tank side wall installation. Provides direct injection
cleaning and forced air drying through the spindles.
Upper Spindle Rack for SteamScrubber Glassware
Washers. Provides direct injection cleaning through
the spindles.
V
Catalog# Description
Shipping Wt.
20 lbs.
(9 kg)
Shipping Wt.
10-359-151
Test Tube Spindle Rack. Includes rack, 150 spindles
20 lbs. (9 kg)
and riser. Dimensions: 21.0" w x 21.5" d x 5.0" h (53.3 x 54.6 x 12.7 cm)
10-359-152
Test Tube Spindle Rack Conversion Kit.
15 lbs. (7 kg)
Includes 150 spindles and riser. Requires Lower
Standard Rack 10-359-118 (not included). Dimensions: 17.5" w x 12.7" d x 4.2" h (44.5 x 32.3 x 10.7 cm)
Test Tube Holders
For use with Test Tube Spindle Racks. Keep tubes upright. Constructed of
Type 304 stainless steel. Holders 10-359-154 and 10-359-155 are
stackable so that two Holders in any combination may be installed in a
Test Tube Spindle Rack at the same time for double capacity. Washers
using stacked Holders can not accommodate an upper rack.
16 lbs.
(7 kg)
Lower Spindle Rack 10-359-202
One is included with every
FlaskScrubber and FlaskScrubber
Vantage Series Glassware Washer.
May be used in place of the Lower
Standard Rack in any SteamVV
Scrubber. Constructed of Type 304
stainless steel. Includes 36 removable
V
spindles, 36 adjustable height clips,
10 small spindles, 18 plastic glassware holders, tool to remove spindles
and 36 nylon plugs. Spindles may be removed and plugged to accommodate
accessory inserts (sold separately). Spindle dimensions: 7.3"
VV
high x 1/4" OD (18.5 x 0.6 cm). Overall dimensions: 21.1" w x 21.0" d
x 8.6" high
V (54 x 53 x 22 cm). Accommodate glassware up to 18.7" (47cm)
high without upper rack in place. Accommodate glassware up to 10.6"
(27 cm) high with upper rack in place. Shipping weight 20 lbs. (9 kg).
VV
V
Test Tube Holder 10-359-154 is stacked atop Test Tube Holder 10-359-155
(sold separately). See page 19.
* Four Utensil Holders maximum in FlaskScrubber and FlaskScrubber Vantage Series Washers.
VV
V
18
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
ACCESSORIES
Utensil Holder 15-352-826
For spatulas, spoons, scoops
and other miscellaneous utensils. Utensils fit vertically in four
compartments, 2.75" w x 3.5" d x
4.9" h (7 x 9 x 12 cm). Type 304
stainless steel. Dimensions: 10.8" w
x 4.1" d x 6.6" h (27 x 11 x 17 cm).
Shipping weight 4 lbs. (2 kg).
V V
st
Above left: Test Tube Holder
10-359-153
Above right: Test Tube Holder
10-359-154
Left: Test Tube Holder 10-359-155
Catalog# Description
Test Tube Holder accommodates 150 each
10 lbs. (5 kg)
10-13 mm OD tubes. Dimensions: 14.3" w x 10.6" d x 6.0" h (36.2 x 27.0 x 15.2 cm).
10-359-154
VV
V
V V
Test Tube Holder accommodates 75 each (7 kg)
15 lbs. (7 kg)
14-20 mm OD tubes. Dimensions: 14.3" w x 10.6" d x 5.5" h (36.2 x 27.0 x 14.0 cm). When tubes are 125 mm or shorter, Holder may be stacked with either 10-359-154 or 10-359-155 (sold separately).
For miscellaneous labware such
as stoppers, spatulas and other
small lightweight items that will
not pass through No. 4 mesh
sides and bottom. Retainer top is
required and included. Type 304
stainless steel. Dimensions: 8.0" w
x 8.0" d x 4.0" h (20 x 20 x 10 cm). Shipping weight 2 lbs. (1 kg).
V V
st
ts
V V
10-359-155
Test Tube Holder accommodates 75 each 15 lbs. (7 kg)
VV V
20-25 mm OD tubes. Dimensions: 14.3" w x V
V
10.6" d x 7.3" h (36.2 x 27.0 x 18.4 cm). When tubes are V
150 mm or shorter, Holder may be stacked with either
10-359-155 or 10-359-154 (sold separately). V
VV
Utensil Basket 15-352-813
V V
Shipping Wt.
VV
10-359-153
V
t
Bulk Tube Insert 15-352-827
Quick loading. For verticallypositioned test tubes. Holds up to
600 each 13 mm tubes or 244 each
20 mm tubes. Bottom, grate size
0.38" (9.5 mm), allows water to
V V
drain from inverted tubes. When
insert is less than fully loaded, the
st ts
divider may be adjusted to keep
tubes upright. Type 304 stainless steel. Smallest divided compartment
size: 1.8" w x 8.1" d x 4.2" h (4 x 21 x 11 cm). Overall interior dimenV V
sions (without
divider): 18.7" w x 8.1" d x 4.2" h (48 x 21 x 11 cm)
Dimensions: 21.0" w x 8.3" d x 4.4" h (53 x 21 x 11 cm). Shipping weight
5 lbs. (2 kg).
Upper Standard Racks
One rack is included with
every SteamScrubber. May be
used in any FlaskScrubber or
FlaskScrubber Vantage Series.
VV
Constructed of Type 304 stainless
steel. Include side release latches
V
and wash arm. Add accessory
inserts suit your glassware mix (sold separately). Dimensions: 20.2" w x
20.9" dV x 6.0" h (51 x 53 x 15 cm).
V
Culture Tube Inserts
Choose from three inserts
designed to hold tubes from
10 to 24 mm OD. Type 304
stainless steel.
V VV
Catalog #
Description 10-359-117
V
Upper Standard Rack for FlaskScrubber and FlaskScrubber Vantage Series Glassware Washers.
Includes side rails for tank side wall installation.
Upper Standard Rack for SteamScrubber
Glassware Washers.
V
10-359-200V
V
Shipping Wt.
16 lbs.
(7 kg)
12 lbs.
(5 kg)
V V
V
Lower Standard Rack
10-359-118
Catalog #
Description Dimensions
1 0-359-119*
VV
240 tubes,
10 mm to 12 mm
18.0" w x 8.6" d x 4.5" h
(46 x 22 x 11 cm)
16.8 mm x
16.8 mm
4 lbs.
(2 kg)
15-352-815
V V
VV
144 tubes,
15 mm to 18 mm
18.0" w x 7.8" d x 6.4" h
(46 x 20 x 16 cm)
23.8 mm x
23.8 mm
3 lbs.
(1 kg)
15-352-816
VV
V V
105 tubes,
20 mm to 24 mm
18.0" w x 8.3" d x 9.9" h
(46 x 21 x 25 cm)
26.5 mm x
26.5 mm
3 lbs.
(1 kg)
st
One is included with every
SteamScrubber. May be used in any
FlaskScrubber or FlaskScrubber
VV
Vantage Series. Constructed of Type
304 stainless steel. Add accessory
V
inserts to suit your glassware mix
(sold separately). Dimensions: 21.1"w x 21.0" d x 3.5" h (54 x 53 x 9 cm).
Shipping weight 10 lbs. (5 kg).
t
t
st
t
t
15-352-817
VV
st
st
Retainer
Top
V 15-352-817
V
* Includes
Retainer Top
VV
V
19
Grid Size Shipping Wt.
18.5" w x 8.3" d x 0.3" h
—
(47 x 21 x 1 cm)
2 lbs.
(1 kg)
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
ACCESSORIES
48-Pin Insert 10-359-122
Forty-eight pins accommodate a
variety of labware. Type 304 stainless steel. Stainless steel pins have
plastic tips to protect glassware
from scratching. Dimensions: 7.8" w
x 19.3" d x 5.2" h (20 x 49 x 13 cm).
Shipping weight 2 lbs. (1 kg).
V V
st
ts
Labware Inserts
V
V
Pins hold a variety of widermouth flasks, beakers and other
labware in inverted position.
Retainer Top is recommended for
V V
use with plastic and lightweight
glassware. Inserts and Retainer
st ts
Top of Type 304 stainless steel.
Stainless steel pins have plastic tips to protect glassware from scratching.
Pipet Inserts
Catalog #
Catalog #
V V
Description V V
1 5-352-808A
10-Pin Insert
16-080-33
32-Pin Insert
16-080-34
Retainer Top
V V
st
Dimensions
Shipping Wt.
19.3" w x 8.8" d x 8.0" h
(49 x 22 x 20 cm)
19.3" w x 8.8" d x 6.0" h
(49 x 22 x 20 cm)
18.5" w x 8.0" d x 0.3" h
(47 x 20 x 1 cm)
3 lbs. (1 kg)
t
Permit
direct injection cleaning
of pipets. Self-sealing silicone check
V
V
valves allow washing of partial or full loads. Type 304 stainless steel.
FlaskScrubber and FlaskScrubber Vantage Series Washers hold up to
four 15-352-808F or two 10-359-123 Inserts.
3 lbs. (1 kg)
2 lbs. (1 kg)
3 lbs.
(1 kg)
Holds 16 pipets, 1 ml to 50 ml. Includes two 1.25"
mounting spindles and PVC-coated holder.
Glassware Holders
Grip glassware over spindles.
Catalog #
V
ts
V V
st
ts
V V
VV
t
Shipping Wt.
0.4 lb.
(0.2 kg)
15-352-808E 6.0" h (15 cm) vinyl-coated
Type 304 stainless steel wire
with height adjustment screw
0.4 lb.
(0.2 kg)
10-359-090*
3.9" h (10 cm) plastic
with Type 304 stainless steel height adjustment clip
0.4 lb. (0.2 kg)
Small Spindles with Clips 10-359-204
Included with every FlaskScrubber and FlaskScrubber Vantage Series
Glassware Washer. Type 304 stainless steel. Spindles may be used in
any spindle location on any Upper or Lower Spindle Rack to provide
direct injection cleaning of small narrowneck
V glassware. Each spindle is
4.3" h x .12.0" OD. Package of 10 small spindles with 10 height adjustment clips, tool to remove large spindles,
VV 36 nylon plugs and 18 height
adjustment clips for large spindles. Shipping weight 3 lbs. (1 kg).
Petri Dish Insert 10-359-120
VV
Description 15-352-808D 4.0" h (10 cm) vinyl-coated
Type 304 stainless steel wire
with height adjustment screw
*Eighteen 10-359-090 Glassware
Holders are included with every
FlaskScrubber and FlaskScrubber
Vantage Series Glassware Washer.
V
t
VV
10-359-123
Type 304 stainless steel. Capacity:
18 bottles. Grid size: 70 mm x 70
mm. Dimensions: 19.5" w x 8.8"
d x 6.0" h (49.5 x 22.2 x 15.2 cm).
Shipping weight 2 lbs. (1 kg).
For pans, instrument trays,
multi-purpose trays and other
shallow containers. Capacity:
5 trays. Type 304 stainless steel.
Dimensions: 18.2" w x 12.2" d x
9.1" h (46 x 31 x 23 cm).
Shipping weight 2 lbs. (1 kg).
VV
Shipping Wt.
2 lbs.
(1 kg)
ts
V V
t
Description 1 5-352-808F Holds 8 pipets, 1 ml to 10 ml. Includes one 1.25" mounting spindle. BOD Bottle Insert 10-359-121
Tray Insert 10-359-203
t
t
For Petri dishes, watch glasses
and microtiter plates. Capacity:
24 plates. Grid size: 22 mm x
140 mm. Type 304 stainless steel.
Dimensions: 19.2" w x 8.6" d x
5.9" h (49 x 22 x 15 cm). Shipping
weight 2 lbs. (1 kg).
Drain Water Cooling Kits
V
Provide plumbing components, solenoid valve and electrical conVV
nections necessary to mix cold tap water
with hot drain water so that
water <60° C (<140° F) is directed to the house drain system. When
the washer’s drainage pump is activated, the solenoid valve opens
releasing the flow of cold tap water to the drain.
DNA Sequencing
Plate Insert 10-359-124
For electrophoresis plates, 10" x
16.6". Capacity: 6 plates. Type 304
stainless steel with plastic glides.
Dimensions: 17.1" w x 8.5" d x
9.9" h (43 x 22 x 25 cm). Shipping
weight 6 lbs. (3 kg).
20
Catalog #
Description Shipping Wt.
10-359-208
Cold Water Drain Kit, 115 volt, 60 Hz operation 8 lbs. (4 kg)
10-359-209
Cold Water Drain Kit, 230 volt, 50/60 Hz operation 8 lbs. (4 kg)
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
ACCESSORIES
&
Detergent
Freestanding-to-Mobile
Conversion Kits
Add mobility to freestanding
SteamScrubber and FlaskScrubber
Glassware Washers. Allow washers
to be plugged into a 20 amp electrical wall outlet and connected to
a standard laboratory sink faucet.
Include four 2-inch diameter rubber
VV
casters, two aerator adapters for connection to standard 55/64"-27 male
and 15/16"-27 female laboratory
faucets, drain hose and installation instructions. Not for use with undercounter washers or FlaskScrubber Vantage Series Glassware Washers.
VV #
Catalog
Description 10-359-206
Mobile Conversion Kit, for 115 volt operation. Includes 10' power cord with NEMA 5/20 plug. 60 lbs.
(27 kg)
LabSolutions Liquid Detergent 04-334-1, Neutralizing Acid Rinse 04-334-2,
and Powder Detergent 04-335 and 04-334
10-359-207
Mobile Conversion Kit, for 230 volt operation.
Includes 8.2' power cord with NEMA 6/20 plug.
60 lbs.
(27 kg)
LabSolutions ™ Non-Foaming Powder Detergent
Shipping Wt.
Specially formulated for Labconco glassware washers. Removes lab
contaminants such as grease, agar, blood and protein digestates.
Rinses completely. Non-foaming formula does not promote leaks.
A 1% solution has a pH of approximately 12.5. Contains phosphates.
Non-hazardous formula may be shipped anywhere.
Description 04-334
Powder Detergent, small pail for approximately 140 loads 10 lbs. (5 kg)
Shipping Wt.
04-335
Powder Detergent, large pail for approximately 400 loads 28 lbs. (13 kg)
LabSolutions ™ Low-Foaming Liquid Detergent
VV
Specially formulated for Labconco glassware washers. Removes a
wide range of laboratory contaminants. Rinses completely. Noncorrosive formula won’t degrade stainless steel, glass or plastic.
Phosphate-free for environmentally-safe disposal. Chlorine-free
and tissue culture-safe. May be used in hot or cold water. For ground
shipment to U.S. or Canada only.
V
Base Stands
Elevate washers 17" (43.2 cm) for washer loading convenience and storage ofVVsupplies. Type 304 stainless steel stationary stand, fully assembled
with
V feet and instructions.
V leveling
V
V #
Catalog
Description 10-359-127
10-359-126
V
V
V
Stand for Freestanding FlaskScrubbers or Steam-
Scrubbers, 24.2" w x 27.5" d x 17.0" h (61 x 70 x 43 cm),
includes one storage compartment with hinged door
Stand for FlaskScrubber Vantage Series,
32.2" w x 27.5" d x 17.0" h (82 x 70 x 43 cm),
includes two storage compartments with hinged doors
Shipping Wt.
80 lbs.
(36 kg)
Catalog #
Description 04-334-1
Low-Foaming Liquid Detergent for approximately
180 loads. 1 gallon (3.8 liters)
Shipping Wt.
12 lbs. (5 kg)
LabSolutions ™ Neutralizing Acid Rinse
105 lbs.
(48 kg)
Specially formulated for rinse aid reservoir in Labconco glassware
washers. Mild acid corrects pH reducing alkaline detergent residue.
Removes hard water deposits, mineral deposits, accumulated lime
scale that can cloud glassware. Rinses completely.
Liquid Detergent Dispenser
Kit 10-359-205
VV
Catalog #
Connects to any SteamScrubber or
FlaskScrubber Glassware Washer
during installation to automate
liquid detergent dispensing.
Includes peristaltic pump, float
switch, tubing, one gallon plastic
container and installation instructions. Detergent is not included.
Not for use with FlaskScrubber
Vantage Series Glassware Washers.
Shipping weight 10 lbs. (5 kg).
For MSDS information, visit our website at www.labconco.com or call
customer service at 800-821-5525 or 816-333-8811.
VV
21
Catalog #
Description 04-334-2
Neutralizing Acid Rinse, fills reservoir approximately
6 times. 34 ounces (1 liter)
Shipping Wt.
3 lbs. (1 kg)
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
COMPANION
PRODUCTS
Glassware Cart 11-928
Glassware Cart 11-925-21
Glassware Carts
Safely transport clean and dirty labware. Come with two large or
four small interchangeable vinyl-coated wire baskets and removable
drip pan below the baskets to catch spills. Include 4" diameter casters
(two with toe locks). Constructed of welded 1-inch square tubular
steel coated with mar-resistant epoxy. Dimensions: 34.9" w x 19.0" d x
36.4" h (88.6 x 48.3 x 92.4 cm). Fully assembled. Lifetime warranty.
ScrubberMate Glassware & Rack Cart 09-682-737
Sixteen combs, each with three pins,
may be placed in sixteen postitions in the
upper drawer and sixteen positions in the
lower drawer.
Upper and lower drawers hold
two inserts each and pull out for
easy access. An upper rack may
be stored on the top; a lower
rack below.
Catalog #
Description 11-928
11-925-21
11-928-3
22-325-142
2-Basket Glassware Cart 43 lbs. (20 kg)
4-Basket Glassware Cart 43 lbs. (20 kg)
Large Basket,
32.0" w x 18.0" d x 4.0" h (81.3 x 45.7 x 10.2 cm)
5 lbs. (2 kg)
Small Basket,
16.0" w x 18.0" d x 4.0" h (40.6 x 45.7 x 10.2 cm)
2 lbs. (1 kg)
Shipping Wt.
Carboy Caddy 04-680
Provides safe way to move a
large container of purified water
without heavy lifting. Includes 3"
diameter casters that elevate the
support shelf only 4.25" above
the floor. Shelf constructed of
phenolic board with a melamine
high-pressure laminate surface.
Frame constructed of welded
1-inch square tubular steel coated
with mar-resistant epoxy. Handle
dimensions: 38.5" high x 19.0"
wide (97.8 x 48.3 cm). Shelf
dimensions: 20.0" x 23.6" (50.8 x 60.0 cm). Supports loads up to 360
pounds (163 kg). Fully assembled. Lifetime warranty. Shipping weight
35 lbs. (16 kg).
ScrubberMate™ Glassware & Rack Cart 09-682-737
Designed for Labconco glassware washers. Provides convenient storage
and transport of extra Labconco washer racks, inserts or miscellaneous
glassware. Accommodates up to two Labconco washer racks or four
wire inserts. Alternatively, 48 adjustable and removable pins, 0.5" wide
x 4.75" high (1.3 cm x 12.1 cm), may be arranged in the drawers to
hold inverted flasks, beakers and other glassware. Rails are provided to
allow a lower washer rack to slide directly onto the cart from the washer. In addition, the lower drawer pulls out for simple loading of inserts
or individual glassware. An upper washer rack may be docked above
the upper drawer. The upper drawer accommodates two wire inserts
and is removable so that tall glassware may be loaded in the lower
drawer. Durable and chemical-resistant, high density polyethylene construction. Includes 2.5" diameter casters with toe locks. Dimensions:
23.3" w x 22.6" d x 31.6" h (59.2 x 57.4 x 80.3 cm). Fully assembled.
Shipping weight 70 lbs. (32 kg).
22
FlaskScrubber® & SteamScrubber® Laboratory Glassware Washers
COMPANION
PRODUCTS
70 Liter Storage Tanks
WaterPro RO Systems
Connect to the WaterPro RO Station to provide
additional storage capacity for RO-purified
water and means to deliver it from three outlets
to destinations such as a polishing station and
glassware washer. Use a gravity feed system for
water delivery. The 70 liter polyethylene tank
has one 3/4 NPT female port and two 3/8" ball
valves with 3/8" female fittings. The tank
includes 6 feet of polyurethane tubing for
connection to the WaterPro RO Station, a 0.3 micron vent filter to help
prevent airborne bacterial contamination of the tank, a float switch to
prevent the WaterPro RO Station from overfilling the tank, a fill valve
wired in series with the float switch that activates when a drop in water
level is detected, and two check valves that direct water to drain if the
water level exceeds normal level. The tank has a powder-coated steel support stand so that it may stand alone up to 6 feet away from the WaterPro
RO Station. Dimensions: 32.8" w x 14.4" d x 26.0" h (83.5 x 36.5 x 66.0 cm).
Connect to Labconco glassware washers to provide purified water for the rinse cycles.
Deliver 1 liter/minute of
reverse osmosis purified,
Type III water when feedwater purity is 100 µs or better.
For wall mounting. Powdercoated steel cabinet with Type
304 stainless steel front panel.
Three bowls made of white
polypropylene. Includes integral 17 liter polyethylene storage tank with outlet port for connection to
washer; ON/OFF switch; µS, TEMP ° C, TIME DISP. and TANK FULL
indicator lights; and DISPENSE switch. If TIME DISP. is activated, water
dispensing from the valve automatically shuts off once user-set time has
elapsed. LED display shows actual water quality from 1 to 999 microsiemens (µS), actual water temperature in ° C or dispense time in minutes.
Requires Prefilter/Carbon Filter Kit 16-307-130 and Reverse Osmosis
Membrane 16-307-102 for operation. Dimensions: 31.1" w x 7.6" d x
30.8" h (79 x 19 x 78 cm).
Catalog #
Electrical Requirements Shipping Wt.
16-307-134
For 115 volts, 60 Hz, 1 amp AC operation. Includes 8-foot, 3-wire cord and plug.
80 lbs. (36 kg)
Catalog #
Electrical Requirements Shipping Wt.
16-307-135* For 230 volts, 50 Hz, 6 amp AC operation. Includes 8-foot, 3-wire cord. An electrical plug is required.
80 lbs. (36 kg)
90-750-20
For 115 volts, 60 Hz, 15 amp AC operation. Includes 115 volt, 60 Hz, 15 amp plug.
90 lbs. (41 kg)
90-750-30*
For 230 volts, 50/60 Hz, 6 amp AC operation. Includes Schuko plug.
90 lbs. (41 kg)
90-750-40
For 230 volts, 50/60 Hz, 6 amp AC operation. Includes North America 230 volt plug.
90 lbs. (41 kg)
90-750-60*
For 230 volts, 50/60 Hz, 6 amp AC operation. Includes British (UK) plug.
90 lbs. (41 kg)
90-750-70*
For 230 volts, 50/60 Hz, 6 amp AC operation. Includes China/Australia plug.
90 lbs. (41 kg)
90-750-80*
For 230 volts, 50/60 Hz, 6 amp AC operation. Includes India plug.
90 lbs. (41 kg)
* International electrical configuration
Support Stand 16-101-6
For converting wall-mounted WaterPro RO
Station to bench mounted. Rests on countertop or other horizontal surface. Powder-coated
steel. Dimensions (with WaterPro RO Station
attached): 31.1" w x 16.1" d x 35.3" h (79 x 41 x
90 cm). Shipping weight 20 lbs. (9 kg).
Prefilter/Carbon Filter Kit 16-307-130 Required for operation.
Includes Prefilters (3) and Carbon Filters (3), for initial start-up and
two filter changes. Shipping weight 10 lbs. (5 kg).
Reverse Osmosis Membrane 16-307-102 Required for opera-
tion. Shipping weight 6 lbs. (3 kg).
23
Contact Labconco for more information about these
quality products for your laboratory.
Water Purification
Systems
Fume Hoods &
Carbon-Filtered
Enclosures
Biological
Safety Cabinets
Safety Enclosures &
Clean Benches
Laboratory Animal
Research Stations
Balance & Bulk Powder
Enclosures
Glove Boxes
Forensic Enclosures
Freeze Dry
Systems
Vacuum Concentrators
& Cold Traps
Multiple Sample
Evaporation Systems
Agricultural Chemistry
Products
Laboratory
Carts & Benches
Blood Drawing
Chairs
Vacuum Desiccator
© 2015 Thermo Fisher Scientific Inc. All rights reserved.
© 2015 by Labconco Corporation
Printed in the U.S.A.
Product design subject to change without notice
Rev 050515
BN0421121